Yamaha S90 El kitabı

Marka: Yamaha

Model: S90

Kategori: Sentezleyici

Tip: El kitabı

Bu kılavuz için de uygundur

Owner’s Manual

S90 XS/S70 XS Owner’s Manual

SPECIAL MESSAGE SECTION

PRODUCT SAFETY MARKINGS: Yamaha electronic

products may have either labels similar to the graphics

shown below or molded/stamped facsimiles of these graph-

ics on the enclosure. The explanation of these graphics

appears on this page. Please observe all cautions indicated

on this page and those indicated in the safety instruction sec-

tion.

The exclamation point within the equi-

lateral triangle is intended to alert the

user to the presence of important operat-

ing and maintenance (servicing) instruc-

tions in the literature accompanying the

product.

The lightning flash with arrowhead sym-

bol, within the equilateral triangle, is

intended to alert the user to the presence

of uninsulated “dangerous voltage”

within the product’s enclosure that may

be of sufficient magnitude to constitute a

risk of electrical shock.

IMPORTANT NOTICE: All Yamaha electronic products

are tested and approved by an independent safety testing

laboratory in order that you may be sure that when it is prop-

erly installed and used in its normal and customary manner,

all foreseeable risks have been eliminated. DO NOT modify

this unit or commission others to do so unless specifically

authorized by Yamaha. Product performance and/or safety

standards may be diminished. Claims filed under the

expressed warranty may be denied if the unit is/has been

modified. Implied warranties may also be affected.

SPECIFICATIONS SUBJECT TO CHANGE: The infor-

mation contained in this manual is believed to be correct at

the time of printing. However, Yamaha reserves the right to

change or modify any of the specifications without notice or

obligation to update existing units.

ENVIRONMENTAL ISSUES: Yamaha strives to produce

products that are both user safe and environmentally

friendly. We sincerely believe that our products and the pro-

duction methods used to produce them, meet these goals. In

keeping with both the letter and the spirit of the law, we

want you to be aware of the following:

Battery Notice: This product MAY contain a small non-

rechargeable battery which (if applicable) is soldered in

place. The average life span of this type of battery is approx-

imately five years. When replacement becomes necessary,

contact a qualified service representative to perform the

replacement.

Warning: Do not attempt to recharge, disassemble, or

incinerate this type of battery. Keep all batteries away from

children. Dispose of used batteries promptly and as regu-

lated by applicable laws. Note: In some areas, the servicer is

required by law to return the defective parts. However, you

do have the option of having the servicer dispose of these

parts for you.

Disposal Notice: Should this product become damaged

beyond repair, or for some reason its useful life is consid-

ered to be at an end, please observe all local, state, and fed-

eral regulations that relate to the disposal of products that

contain lead, batteries, plastics, etc.

NOTICE: Service charges incurred due to lack of knowl-

edge relating to how a function or effect works (when the

unit is operating as designed) are not covered by the manu-

facturer’s warranty, and are therefore the owners responsi-

bility. Please study this manual carefully and consult your

dealer before requesting service.

NAME PLATE LOCATION: The graphic below indicates

the location of the name plate. The model number, serial

number, power requirements, etc., are located on this plate.

You should record the model number, serial number, and the

date of purchase in the spaces provided below and retain this

manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

92-469- 1 (rear)

S90 XS/S70 XS Owner’s Manual

Information for Users on Collection and Disposal of Old Equipment

This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic

products should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in

accordance with your national legislation and the Directives 2002/96/EC.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative

effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste

disposal service or the point of sale where you purchased the items.

[For business users in the European Union]

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

[Information on Disposal in other Countries outside the European Union]

This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and

ask for the correct method of disposal.

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not fit into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table specified

by the manufacturer, or sold with

the apparatus. When a cart is

used, use caution when moving

the cart/apparatus combination

to avoid injury from tip-over.

13 Unplug this apparatus during

lightning storms or when unused for long periods of

time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(UL60065_03)

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

S90 XS/S70 XS Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical

shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

• Only use the voltage specified as correct for the instrument. The required voltage

is printed on the name plate of the instrument.

• Check the electric plug periodically and remove any dirt or dust which may have

accumulated on it.

• Use only the supplied power cord/plug.

• Do not place the power cord near heat sources such as heaters or radiators, and

do not excessively bend or otherwise damage the cord, place heavy objects on

it, or place it in a position where anyone could walk on, trip over, or roll anything

over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the instrument or attempt to disassemble the internal parts or

modify them in any way. The instrument contains no user-serviceable parts. If it

should appear to be malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill into

any openings. If any liquid such as water seeps into the instrument, turn off the

power immediately and unplug the power cord from the AC outlet. Then have the

instrument inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• If the power cord or plug becomes frayed or damaged, or if there is a sudden

loss of sound during use of the instrument, or if any unusual smells or smoke

should appear to be caused by it, immediately turn off the power switch,

disconnect the electric plug from the outlet, and have the instrument inspected

by qualified Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage

to the instrument or other property. These precautions include, but are not limited to, the following:

• Always connect the three-pin attachment plug to a properly grounded power

source. (For more information about the main power supply, see page 16.)

• When removing the electric plug from the instrument or an outlet, always hold

the plug itself and not the cord. Pulling by the cord can damage it.

• Remove the electric plug from the outlet when the instrument is not to be used

for extended periods of time, or during electrical storms.

• Do not connect the instrument to an electrical outlet using a multiple-connector.

Doing so can result in lower sound quality, or possibly cause overheating in the

outlet.

• Do not expose the instrument to excessive dust or vibrations, or extreme cold or

heat (such as in direct sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration or damage to the internal

components.

• Do not use the instrument in the vicinity of a TV, radio, stereo equipment, mobile

phone, or other electric devices. Otherwise, the instrument, TV, or radio may

generate noise.

• Do not place the instrument in an unstable position where it might accidentally

fall over.

• Before moving the instrument, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using is

easily accessible. If some trouble or malfunction occurs, immediately turn off

the power switch and disconnect the plug from the outlet. Even when the power

switch is turned off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time, make sure to unplug

the power cord from the wall AC outlet.

Power supply/Power cord

Do not open

Water warning

Fire warning

If you notice any abnormality

Power supply/Power cord

Location

(1)-12 1/2

S90 XS/S70 XS Owner’s Manual

• Before connecting the instrument to other electronic components, turn off the

power for all components. Before turning the power on or off for all components,

set all volume levels to minimum. Also, be sure to set the volumes of all

components at their minimum levels and gradually raise the volume controls

while playing the instrument to set the desired listening level.

• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,

solvents, cleaning fluids, or chemical-impregnated wiping cloths.

• Never insert or drop paper, metallic, or other objects into the gaps on the panel

or keyboard. If this happens, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument inspected by qualified

Yamaha service personnel.

• Do not place vinyl, plastic or rubber objects on the instrument, since this might

discolor the panel or keyboard.

• Do not rest your weight on, or place heavy objects on the instrument, and do not

use excessive force on the buttons, switches or connectors.

• Do not use the instrument/device or headphones for a long period of time at a

high or uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

Saving and backing up your data

• DRAM data (refer to the Reference Manual <separate PDF documentation>) is

lost when you turn off the power to the instrument. Save the data to the flash

ROM/the internal flash memory (see page 47)/a USB storage device/external

device such as a computer.

Data stored to the flash ROM may be lost due to malfunction or incorrect

operation. Save important data to a USB storage device/external device such as

a computer.

• Never attempt to turn off the power while data is being written to Flash ROM

(while an “Executing...” or “Please keep power on” message is shown). Turning

the power off in this state results in loss of all user data and may cause the

system to freeze (due to corruption of data in the Flash ROM). This means that

this synthesizer may not be able to start up properly, even when turning the

power on next time.

Backing up the USB storage device/external media

• To protect against data loss through media damage, we recommend that you

save your important data onto two USB storage devices/external media.

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

Always turn the power off when the instrument is not in use.

Connections

Maintenance

Handling caution

Saving data

(1)-12 2/2

S90 XS/S70 XS Owner’s Manual

Welcome

A message from the S90 XS/S70 XS Development Team

Thank you for purchasing the Yamaha S90 XS/S70 XS Music Synthesizer.

We’re extremely proud to introduce the new S90 XS/S70 XS as the successor to the original S90 ES. Equipped with

exceptionally high-quality musical instrument sounds and a real piano-feel response, this is truly the instrument of choice

for musicians and players worldwide, whatever the genre. Drawing on our long experience cultivated through years of

synthesizer development, we designed this model not only for top professional musicians, but also for casual players

and hobby musicians who want to have a greater level of high-quality sound, playability and advanced features—

especially in live performance applications. To complete this lineup, we've added the S70 XS, a 76-key model which

maintains the same keyboard touch as the 88-key model, yet provides the added value of portability.

The advanced and convenient features of the S90 XS/S70 XS do not stop there. The Remote Control functions and the

Master Keyboard features have been enhanced and made more powerful to meet the demands of professional music

production. We are proud and confident that the S90 XS/S70 XS can aid in your music making, and we're sure that it will

be your first ‘go-to’ instrument in music situation, live performance, recording and so on.

In order to take full advantage of the S90 XS/S70 XS’s functionality, please read this manual carefully. We also

recommend that you keep this manual in a safe and handy place for future reference.

We really hope that the S90 XS/S70 XS will help your creativity and musical work grow by leaps and bounds.

Enjoy!

Sincerely,

The Yamaha S90 XS/S70 XS Development Team

Accessories

• AC Power cord

• Owner’s Manual (this book)

• Owner’s Manuals CD-ROM x 1 (Reference Manual, Data List)

• Disk x 1 (containing DAW software)

About the accessory disk

Special Notice

• The software included in the accessory disk and the

copyrights thereof are under exclusive ownership by

Steinberg Media Technologies GmbH.

• Use of the software and this manual is governed by the

license agreement which the purchaser fully agrees to upon

breaking the seal of the software packaging. (Please read

carefully the Software Licensing Agreement before installing

the application.)

• Copying of the software or reproduction of this manual in

whole or in part by any means is expressly forbidden without

the written consent of the manufacturer.

• Yamaha makes no representations or warranties with regard to

the use of the software and documentation and cannot be

held responsible for the results of the use of this manual and

the software.

• This disk is NOT for audio/visual purposes. Do not attempt to

play the disk on an audio/visual CD/DVD player. Doing so may

result in irreparable damage to your player.

• Note that Yamaha does not offer technical support for the

DAW software in the accessory disk.

About the DAW software in the

accessory disk

The accessory disk contains DAW software both for Windows

and Macintosh.

NOTE

• Make sure to install DAW software under the “Administrator” account.

• In order to have continuous use of Cubase AI 4, including support and

other benefits, you will need to register the software and activate your

software license by starting it while the computer is connected to the

Internet. Click the “Register Now” button shown when the software is

started, then fill in all required fields for registration. If you do not

limited period of time expires.

• If you are using a Macintosh computer, double-click the “***.pkg” file to

start installation.

For information about the minimum system requirements and

latest information on the software in the disk, check the web site

below.

http://www.yamahasynth.com/download/

About software support

Support for the DAW software in the accessory disk is provided

by Steinberg on its website at the following address.

http://www.steinberg.net

You can visit the Steinberg site also via the Help menu of the

included DAW software. (The Help menu also includes the PDF

manual and other information on the software.)

S90 XS/S70 XS Owner’s Manual

S90 XS/S70 XS Main Features

 Huge amount of waveforms and vast sound selection, including top-quality piano sounds

The S90 XS/S70 XS features a whopping 142 MB of exceptionally high-quality piano waveforms, including many

newly sampled sounds, and a vast variety of Voices directly derived from the flagship MOTIF XS Music Production

Synthesizer-giving you a total of 456 MB of available waveforms.

 Balanced Hammer Keyboard—with both 88 and 76 keys—provides natural touch and

response

The S90 XS/S70 XS features a sophisticated Balanced Hammer Keyboard (with Initial Touch/Aftertouch) which utilizes

Yamaha’s long-standing know-how cultivated in its acoustic piano and synthesizer development. The 88-key model

gives you full-scale piano performance, while the smaller 76-key model offers greater portability and ease in

transporting.

 Performance Creator

The S90 XS/S70 XS features a Performance Creator function which provides quick and easy Layer/Split /Drum Assign

assignments of your original Performances based on your favorite Voices. You can utilize the current effects and

settings of the Voices, allowing you to come up with your own original Voices very quickly.

 Intuitive Panel Composition

The buttons, Knobs and Sliders are well designed and logically placed for optimum, intuitive operation, especially in

live performance. For example, you can quickly select a Part, use the Part switch to turn it on/off, set the Arpeggio

switch on/off, switch Arpeggio Hold on/off—all with the top panel controls—and edit important parameters via the

Knobs and Sliders. A convenient Panel Lock function, which prevents unintended changes during performance, and

a Tap Tempo function for the Arpeggio are also available on the top panel.

 Audio Rec/Play Function

You can record your performance to a USB storage device or internal flash memory as a wave file, or you can play

back audio files which have been created on DAW software. You can also play the keyboard along with audio file

playback via the Audio Rec/Play function.

 DAW Remote Function

The S90 XS/S70 XS features a DAW Remote function for music production convenience. This allows you to store 50

different control templates and have easy, intuitive control over your main DAW software and VST instruments directly

from the panel controls of the S90 XS/S70 XS.

 Voice Editor and Remote Editor for Detailed Editing

When using Cubase series software compatible with VST3 technology, the S90 XS/S70 XS Editor VST can be

conveniently used in the same manner as software VST instruments for editing the detailed parameters. When using

in stand-alone mode, the S90 XS/S70 XS Editor for Studio Manager V2 is also available to edit the detailed

parameters. For setting of the Remote Control function and the Remote Template, the S90 XS/S70 XS Remote Editor

allows you to manage them. You can download them on our web site.

http://www.yamahasynth.com/download/

S90 XS/S70 XS Owner’s Manual

About this Manual

Owner’s Manual (this book)

Explains operations of the top panel controls.

PDF documentation (includes the Owner’s Manual CD-ROM)

 Reference Manual

Explains in detail about the sound-related parameters and effect parameters.

 Data List

This contains various important lists such as the Voice List, Wave List, Multi List, MIDI Implementation Chart,

Performance List, Master Program List, Mixing Template List, Arpeggio Type List and Remote Control Function List.

Special Notice

• The contents of this Owner’s Manual and the copyrights thereof are under exclusive ownership by Yamaha Corporation.

• The illustrations and LCD screens as shown in this Owner’s Manual are for instructional purposes only, and may appear somewhat

different from those on your instrument.

• This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect to which

it has license to use others’ copyrights.

Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and

sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws.

Any violation of copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

• This device is capable of using various types/formats of music data by optimizing them beforehand to the proper format music data

for use with the device. As a result, this device may not play them back precisely as their producers or composers originally intended.

Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited

except for your personal use.

• Such copyrighted materials include, without limitation, all computer software, style files, MIDI files, WAVE data, musical scores and

sound recordings. Any unauthorized use of such programs and contents outside of personal use is not permitted under relevant laws.

Consult a legal advisor before using such data.

• Windows is the registered trademark of Microsoft

Corporation.

• Apple and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries.

• Steinberg and Cubase are the registered trademarks of Steinberg Media Technologies GmbH.

• The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their respective

companies.

• All other trademarks are the property of their respective holders.

How to use the PDF manuals

The Reference Manual and the Data List are provided as data documents in PDF format. These PDF files can be

viewed and read on a computer. When using Adobe

Reader

to view a PDF file, you can search for specific

words, print a specific page or link to open a desired section in the manual. The term search and link functions are

especially convenient methods of navigating through a PDF file, and we recommend that you use them.

The latest version of Adobe Reader can be downloaded from the following URL.

http://www.adobe.com/products/reader/

S90 XS/S70 XS Owner’s Manual

Welcome............................................................................... 6

Accessories.......................................................................... 6

About the accessory disk..................................................... 6

S90 XS/S70 XS Main Features.............................................. 7

About this Manual................................................................. 8

Controls and Functions 10

Top panel ........................................................................... 10

Rear Panel .......................................................................... 15

Setting Up 16

Power Supply ..................................................................... 16

Connecting speakers or headphones................................ 16

Powering Up the System .................................................... 16

Adjusting the volume and the brightness of the display .... 17

Starting Up ......................................................................... 17

Selecting Voices................................................................. 17

Playing demo songs........................................................... 17

Resetting the User Memory to the Initial Factory Settings . 18

Start Guide 19

Modes ........................................................................... 19

Basic Instructions........................................................ 20

Playing the Keyboard in the Voice mode .................. 21

Selecting a preset Voice .................................................... 21

Using the Category Search function .................................. 22

Grouping your most-used Voices together—Favorite

Category............................................................................. 22

Changing the tonal qualities of the Voice........................... 23

Voice Editing ...................................................................... 24

Enhancing the sound with Effects ...................................... 24

Using the Arpeggio function .............................................. 26

Creating a New Performance by Using Your Favorite

Voice (Performance Creator) ...................................... 28

Layer—Playing different Voices together........................... 28

Split—Playing two different Voices with your left and right

hands.................................................................................. 29

Drum Assign—Layering a drum Part with the current Voice

............................................................................................ 30

Changing the drum pattern (Arpeggio Type)..................... 30

Assigning a name to the Performance ............................... 31

Playing the Keyboard in the Performance Mode ...... 32

Selecting a Performance .................................................... 32

Changing the timbre of the Voice....................................... 32

Singing with a Connected Microphone ..................... 33

Recording/Playing Back with a USB Storage Device

(Audio Record/Play Mode) .......................................... 34

Recording........................................................................... 34

Playing back the recording ................................................ 35

Using a Connected Computer .................................... 36

Connecting to a computer ..................................................36

Using as a multi-timbral tone generator (Multi mode) ........38

Remote-controlling the software (Remote mode) ...............38

Editing more detailed parameters of the Voice ..................40

Playing the Keyboard Along with Playback of the MIDI

File................................................................................. 41

Using as a Master Keyboard (Master Mode) ............. 43

Storing the Edited Voice/Performance/Multi .......................43

Making settings for use as a master keyboard...................43

Making Global System Settings (Utility Mode) ......... 45

Saving/Loading Data (File Mode) ............................... 47

Saving the settings to a USB storage device .....................47

Loading the settings from a USB storage device ...............48

USB storage devices ..........................................................49

Appendix 50

Display Messages........................................................ 50

Troubleshooting .......................................................... 52

Specifications .............................................................. 58

Index ............................................................................. 59

Contents

S90 XS/S70 XS Owner’s Manual

Controls and Functions

Top panel

Keyboard

The S90 XS features a 88-key keyboard, while the S70 XS has 76

keys. All are equipped with a touch response feature (both initial

touch and after touch). With initial touch, the instrument senses

how strongly or softly you play the keys, and uses that playing

strength to affect the sound in various ways, depending on the

selected Voice. With after touch, the instrument senses how

much pressure you apply to the keys while playing, and uses

that pressure to affect the sound in various ways, depending on

the selected Voice.

NOTE

The keyboard range of the S90 XS is A -1 to C7; the range of the

S70 XS is E0 to G6.

Pitch Bend wheel

Controls the pitch bend effect. You can also assign other

functions to this controller.

Modulation wheel

Controls the modulation effect. You can also assign other

functions to this controller.

MASTER VOLUME slider

Adjusts the volume of the overall sound. Move the slider

upwards to raise the output level from the OUTPUT L/R jacks

and the PHONES jack.

[MIC ON/OFF] button

Press the [MIC ON/OFF] button to switch the on/off status of the

MIC INPUT jack.

INPUT GAIN knob

Use this to adjust the input gain of the audio signals at the MIC

INPUT jack. Depending on the connected microphone, you may

need to adjust this for optimum level. The volume level is

increased as the knob is rotated to the right and decreased as it

is rotated to the left.

PEAK indicator

This indicator lights up when the input signal level is 3dB below

clipping. Adjust the INPUT GAIN so that the indicator rarely

lights up at signal peak.

Performance Control buttons

These buttons let you control the functions that affect

Performances and Multis. You can select the part to be

controlled by the knobs and set the Arpeggio-related

parameters for each Part. In the Multi mode, the four parts to be

edited will correspond to 1 – 4, 5 – 8, 9 – 12 or 13 – 16

(depending on the currently selected Part).

[COMMON] button

In the Performance mode, pressing this button lets you use

the knobs to control the Common parameters.

In the Performance Edit mode, pressing this button will call

up the Common Edit Select display.

[PART SELECT] 1 – 4 buttons

In the Performance mode and Multi mode, pressing one of

these buttons will select the Part to be controlled by the

knob.

In the Voice Edit mode, pressing one of these buttons will

select the Element to be edited via the Quick Edit function.

C1E0 F0 G0 A0 B0C0 D0A-1 B-1 C2

S90 XS/S70 XS Owner’s Manual

Controls and Functions

[PART ON/OFF] 1 – 4 buttons

These buttons turn each Part on and off. In the Voice mode,

only Part 1 is available and is always turned on.

[ARP ON/OFF] button

Turns the “Arp Switch” (a common parameter) on/off. When

this button is turned on, the Arpeggio function is available.

[PART ARP] 1 – 4 buttons

Turn Arpeggio playback on or off for each Part in the

Performance/Multi Mode.

In the Voice mode, pressing either of the [ARP ON/OFF] and

[PART ARP] 1 buttons will turn the Arpeggio playback on or

off for Part 1, since only Part 1 is available.

[HOLD] 1 – 4 buttons

When some of these buttons are turned on, the Arpeggio

playback of the corresponding Parts cycles automatically

even if you release your fingers from the keys, and continues

to cycle until the next key is pressed. In other words, these

buttons turn the “Arp Hold” (a part parameter) on or off. In

the Voice mode, only Part 1 is available.

Slider Function button

Pressing this button changes the functions assigned to the four

Sliders. The lamp next to the currently active parameters will

light.

In the Voice Edit mode, pressing this button a few times will turn

all the lamps off, indicating that the Sliders can be used to

control the Element levels of the currently edited Voice.

Sliders

These control the parameter selected via the Slider Function

button.

In the Voice mode, only the leftmost Slider is available.

In the Performance mode and Multi mode, these Sliders control

the parameter of the corresponding Parts.

In the Master mode, when “Zone Switch” and “Knob Slider Zone

Switch” are on, the Sliders will control the MIDI Control Change

message that is specified for each zone. Otherwise, the function

is the same as that in the Voice/Performance/Multi mode.

NOTE

If all of the Sliders are set to the minimum, you may not hear any

sound from the instrument, even when playing the keyboard. If

this is the case, raise all the Sliders to a suitable level.

NOTE The MASTER VOLUME slider adjusts the audio output level from

this instrument. On the other hand, these Sliders adjust the

volume for the Part of the Performance/Multi as a parameter.

Accordingly, the values set via the Sliders can be stored as the

Voice, Performance, Song, or Pattern data.

C3 C4 C5 C6 C7

S90 XS/S70 XS Owner’s Manual

Controls and Functions

Knob Function buttons

Pressing these buttons change the functions assigned to the

four Knobs. The lamp next to the currently active parameters will

light. In the Voice mode, the function of each Knob is applied to

the current Voice; in the Performance/Multi mode, the function of

each Knob is applied only to the currently selected Part (or to all

Parts depending on the setting).

NOTE

Controlling the Knobs of the “EFFECT” function will always affect

the sound of all Parts. Controlling the Knobs of the “MIC”

function will work independently.

Knobs

These four highly versatile Knobs let you adjust various aspects

or parameters of the current Voice. Use the Knob Function

buttons to change the parameter set for the Knobs.

Arpeggio/Effect Function button

Pressing this button changes the functions assigned to the five

Function buttons. You can select one of two different functions:

selecting the Arpeggio from 1 – 5 and turning each effect on/off.

[DAW REMOTE] button

The Remote mode lets you control sequencer software on your

computer from the panel controls of the instrument. Turn the

[DAW REMOTE] button on to enter the Remote mode.

Function buttons

In the Remote mode, “Top,” “Repeat On/Off,” “Stop,” “Play” and

“Record” are assigned to each of these buttons.

In other modes, the functions specified via the Arpeggio/Effect

Function button are assigned to these buttons.

ASSIGNABLE FUNCTION [1]/[2] buttons

You can call up a specific Element of the selected Voice by

pressing each of these buttons during your keyboard

performance. In addition, you can assign other functions to

these buttons.

OCTAVE [-]/[+] buttons

Use these buttons to change the note range of the keyboard. To

restore the normal octave setting, press both buttons

simultaneously.

TRANSPOSE [

-]/[+

]

buttons

Use these buttons to raise or lower the pitch of the note by one

semitone. To restore the normal octave setting, press both

buttons simultaneously.

LCD (Liquid Crystal Display)

The backlit LCD displays the parameters and values related to

the currently selected operation or mode.

[SHIFT] button

Pressing this button along with another button enables you to

execute various commands. The main functions are as follows.

NOTE

All the functions are listed in the Data List (PDF file).

Data dial

For editing the currently selected parameter. To increase the

value, turn the dial right (clockwise); to decrease the value, turn

the dial left (counter-clockwise). If a parameter with a wide value

range is selected, you can change the value in broader strokes

by quickly turning the dial.

[INC] button

For increasing the value of the currently selected parameter.

[DEC] button

For decreasing the value of the currently selected parameter.

[SHIFT] + Functions

START/STOP CLICK ON/OFF

AUDIO REC/PLAY Move to Rec Standby display in the Audio Rec/

Play mode

VOICE Bulk dump the edited Voice

PERFORM Bulk dump the edited Performance

MULTI/SEQ PLAY Bulk dump the edited Multi

ENTER Tap tempo for the Arpeggio

INC/DEC, Data dial Change the program number ±10.

Change the selected parameter ±10 on Edit

display

Cursor [ ]/[ ] Select the display mode in the LCD

Knobs 1 – 4 Change the parameter value continuously

FAVORITE Add/remove the current Voice/Performance/

Multi to/from the favorite category

PANEL LOCK Move to Utility Panel Lock display

S90 XS/S70 XS Owner’s Manual

Controls and Functions

Cursor buttons

The cursor buttons move the “cursor” around the LCD display

screen, highlighting and selecting the various parameters.

[EXIT] button

The menus and displays of the S90 XS/S70 XS are organized

according to a hierarchical structure. Press this button to exit

from the current display and return to the previous level in the

hierarchy. Also use it to cancel a Job or a Store operation.

[ENTER] button

Use this button to call up the display of the selected menu. Also

use this button to execute a Job or a Store operation.

Mode buttons

These buttons select the S90 XS/S70 XS operating modes (e.g.,

Voice mode).

PERFORMANCE CREATOR

This function is for quickly editing/creating a new Performance

based on the current Voice. This would come in handy when a

certain Voice has effect settings that you want to use in your

Performance program.

[LAYER] button

This function is for editing a layer Performance based on the

current Voice. When pressing this button, the Category

Search display appears on the display and you can select

the Voices for use in a layer.

[SPLIT] button

This function is for editing a split Performance based on the

current Voice. When pressing this button, the Category

Search display appears on the display and you can select

the Voices for use in a split.

[DRUM ASSIGN] button

This function is for editing a Performance with a Drum Voice

based on the current Voice. When pressing this button, the

Category Search display appears on the display and you

can select the desired Drum Voice. Also, Arpeggio will be

set to on automatically.

BANK [DEC]/[INC] buttons

Each button selects a Voice or Performance Bank.

[CATEGORY SEARCH] button

When this button is turned on in the Voice/Multi/Performance

Part Edit mode, the [A] – [H] buttons can be used to select the

main category of the Voice. When this button is turned on in the

Performance mode, the [A] – [H] buttons can be used to select

the main category of the Performance.

[FAVORITE] button

Use this convenient function to store all your favorite, often-used

Voices in a single, easy-to-access location and call them up by

pressing the [FAVORITE] button. You can add the current

program to a favorite category by simultaneously holding down

the [SHIFT] button and pressing this button. This is one more

useful way you can quickly select the Voices you need from the

huge number available on the instrument.

[A] – [H] buttons

Each button selects a Program.

When the [CATEGORY SEARCH] button is turned on, these

buttons can be used to select the Main category (printed below

each button).

[PART] button

[MUTE] button

[SOLO] button

Changes the function of the Number [1] – [16] button. (Refer to

“Number [1] – [16] buttons” section.)

[PANEL LOCK] button

Turning on this button disables the panel operations. The Panel

Lock function can temporarily disable panel operations and

prevent unintended operation during live performance. The

Panel Lock function affects all controls, with the exception of the

Modulation wheel, the Pitch Bend wheel, Footswitch, INPUT

GAIN and the MASTER VOLUME. The target buttons for the

Panel Lock function can be set up in the Utility Panel Lock

display.

S90 XS/S70 XS Owner’s Manual

Controls and Functions

Number [1] – [16] buttons

Use of these buttons differs depending on the on/off status of the

[PART], [MUTE] and [SOLO] buttons. The indicator lights if each

button is turned on

Mode [PART] [MUTE] [SOLO]

Voice Play Keyboard transmit channel setting — —

Normal Voice Edit — Element selection ([1] – [8])

Element Mute setting ([9] – [16])

Element selection ([1] – [8] or [9] – [16])

Performance Play Keyboard transmit channel setting Part Mute setting ([1] – [4]) Solo part selection ([1] – [4])

Performance Edit Part selection ([1] – [4]) Part Mute setting ([1] – [4]) Solo Part selection ([1] – [4])

Multi Play Part selection ([1] – [16]) Part Mute setting ([1] – [16]) Solo part selection ([1] – [16])

Multi Edit Part selection ([1] – [16]) Part Mute setting ([1] – [16]) Solo part selection ([1] – [16])

Master Play Keyboard transmit channel setting (when

memorizing the Voice mode or

Performance mode to the current Master)

or Part selection (when memorizing the

Multi mode to the current Master)

Part Mute setting ([1] – [4]) (Performance)

Part Mute setting ([1] – [16]) (Multi)

Solo Part selection ([1] – [4])

(Performance)

Solo Part selection ([1] – [16]) (Multi)

Master Edit Changes the Edit mode from Common

Edit to Zone Edit and Zone selection ([1] –

[4])

——

S90 XS/S70 XS Owner’s Manual

Controls and Functions

Rear Panel

(Power switch)

Press to turn power ON ( ) or OFF ().

AC IN socket

Connects to the included power cord.

Use only the AC power cord supplied with the S90 XS/S70 XS.

MIDI IN, OUT, and THRU terminals

MIDI IN is for receiving control or performance data from another

MIDI device, such as an external sequencer. Use this connector

to control the synthesizer from an external MIDI device. MIDI

OUT is for transmitting all control, performance and playback

data from the S90 XS/S70 XS to another MIDI device, such as an

external sequencer.

Likewise, you can use the S90 XS/S70 XS to control external

MIDI instruments. MIDI THRU is simply for redirecting any

received MIDI data (via MIDI IN) to connected devices, allowing

convenient chaining of additional MIDI instruments.

FOOT SWITCH jacks

For connection of an optional FC3/FC4/FC5 Footswitch to the

SUSTAIN jack and a FC4/FC5 Footswitch to the ASSIGNABLE

jack. When connected to the SUSTAIN jack, the Footswitch

controls sustain. When connected to ASSIGNABLE, it can

control one of various different assignable functions.

FOOT CONTROLLER 1 and 2 jacks

An optional foot controller (FC7, etc.) can be connected here.

Each jack lets you continuously control one of various different

assignable functions--such as volume, tone, pitch, or other

aspects of the sound.

LCD Contrast control

Use this control to set the LCD display for optimum legibility.

USB connectors

There are two different types of USB connectors, and the rear

panel of the instrument features both. The USB TO HOST

connector is used to connect this instrument to the computer via

the USB cable. The USB connection between the instrument and

the computer can only be used for transfer of MIDI data. Unlike

MIDI, USB can handle multiple ports via a single cable. The USB

connection between the instrument and the computer can only

be used for transfer of MIDI data. No audio data can be

transferred via USB.

The USB TO DEVICE connector is used to connect this

instrument to a USB storage device (hard disk drive, CD-ROM

drive, flash disk, etc.) via USB. This lets you save the data

created on this instrument to an external USB storage device as

well as load data from the device to the instrument. Save/Load

operations can be performed in the File mode.

ASSIGNABLE OUT L and R jacks

These outputs are independent of the main output (at the L/

MONO and R jacks below), and can be freely assigned to any of

the Drum Voice keys or the Parts. This lets you route specific

Voices or sounds for processing with a favorite outboard effect

unit.

The Parts which can be assigned to these jacks are as follows:

• Drum Voice key to which the drum/percussion instrument is

assigned

• Each part of the Performance*

• Each part of the Multi*

• Click (metronome)

*Includes the Audio Input Part (A/D IN Part)

OUTPUT L/MONO and R jacks

Line level audio signals are output via these phone jacks. For

monophonic output, use just the L/MONO jack.

PHONES jack

A pair of headphones can be plugged in here. (Standard stereo

phone jack)

MIC INPUT jack

External audio signals can be input via this combo jack. A

microphone can be connected to the MIC INPUT jacks. This

audio can be used as input for the A/D Input Part in the

Performance/Multi mode. Use an XLR plug or 1/4" mono phone

plug.

S90 XS/S70 XS Owner’s Manual

Setting Up

Power Supply

Connect the supplied AC power cord in the following

order. Make sure the Power switch on the S90 XS/S70 XS

is set to OFF.

1 Connect the supplied power cord to the AC IN

on the instrument’s rear panel.

2 Connect the other end of the power cord to

an AC outlet.

NOTE Follow this procedure in reverse order when disconnecting the

power cord.

CAUTION

Make sure your S90 XS/S70 XS meets the voltage requirement for the

country or region in which it is being used. The power cord includes a

grounding pin to prevent electrical shock and damage to equipment.

When connecting to an outlet, connect the adaptor’s ground lead to

the ground screw. If you’re unsure how to connect, then contact your

Yamaha dealer or service center (page 63).

WARNING

Use only the AC power cord supplied with the S90 XS/S70 XS. The

use of an inappropriate replacement can pose a fire and shock

hazard!

CAUTION

Even when the switch is in the OFF position, a small amount of

electricity is still flowing to the unit. When you are not using the S90

XS/S70 XS for a long time, make sure to unplug the AC power adaptor

from the wall AC outlet.

Connecting speakers or

headphones

Since the S90 XS/S70 XS has no built-in speakers, you

will need to monitor the sound of the instrument by using

external equipment. Connect a set of headphones,

powered speakers, or other playback equipment as

illustrated below. When making connections, be sure that

your cables have the appropriate ratings.

Powering Up the System

Make sure the volume settings of the S90 XS/S70 XS and

external devices such as powered speakers are turned

down to the minimum before turning the power on.

When connecting the S90 XS/S70 XS to the powered

speakers, turn on the power switch of each device in the

following order.

When turning the power on:

First, the S90 XS/S70 XS, then the connected powered

speakers.

When turning the power off:

First, the connected powered speakers, then the S90 XS/

S70 XS.

Please keep in mind that the Power switch is located at

the right side (from the view of the keyboard) of the AC IN

socket on the rear panel of the S90 XS/S70 XS.

AC IN

Power switch

S90 XS/S70 XS

Powered speaker (Left) Powered speaker (Right)

Headphones

OUTPUT L/MONO OUTPUT R

PHONES

S90 XS/S70 XS Owner’s Manual

Setting Up

Adjusting the volume and

the brightness of the

display

Adjust the volume levels of the S90 XS/S70 XS and the

connected amplifier/speaker system.

NOTE When connecting to a set of powered speakers or PA

equipment, set the MASTER VOLUME to about 70%, then raise

the volume of the powered speakers or PA equipment to the

appropriate level.

If the display is not easily visible, use the LCD

CONTRAST knob on the rear panel to adjust for optimum

visibility.

CAUTION

Do not listen with the headphones at high volume for long periods of

time. Doing so may cause hearing loss.

Starting Up

Try playing some of the realistic and dynamic S90 XS/S70

XS sounds from the keyboard now. When you turn the

power on, the display below appears.

NOTE In the default settings, the Master mode is selected. See

page 19 for details about the modes.

NOTE Keep in mind that the example displays shown in this manual are

for instruction purposes only, and may appear somewhat

different from those on your instrument.

In this condition you can play the keyboard and hear the

sounds of the selected program.

In the default setting, the Master mode provides a total of

128 programs each of which includes the mode (Voice,

Performance, Multi) and its program number.

The top of the Master Play display indicates the Master

program number and the status (Mode, Bank, Program

Number and its name) registered to the current Master

program.

NOTE For details about Banks, see pages 21 and 32.

Selecting Voices

In the default setting, the Master mode provides a total of

128 programs each of which includes the mode (Voice,

Performance, Song and Multi) and its program number.

Try out the different Master programs to play various

Voices and Performances. You can change the Master

program number by using the [INC] button, [DEC] button,

or the data dial.

Playing demo songs

The S90 XS/S70 XS features a variety of demo songs,

showcasing its dynamic sound and sophisticated

functions. Here’s how to play them back.

NOTE Make sure the S90 XS/S70 XS is ready for playback. Details are

given in the section “Setting Up” on page 16.

1 Simultaneously hold the [FILE] button and

press the [UTILITY] button.

2 The DEMO screen is shown in the display.

Select the song with the data dial or cursor

[ ]/[ ] buttons.

3 Press the [ENTER] button to start playback of

the DEMO song.

Pressing the [ENTER] button during playback stops

playback at the current point in the Song then

pressing this again starts playback from that point.

4 To stop playback, press the [EXIT] button.

5 To close the Demo Song display, press any of

the [EXIT], [VOICE], [PERFORM], [MASTER]

and [MULTI/SEQ PLAY] buttons.

S90 XS/S70 XS

Max.

Min.

Dark Light

Adjust the display

contrast with the LCD

CONTRAST knob.

Adjust the volume with

the MASTER VOLUME

slider.

Mode Bank Program number

Program name Master program number

Increases numberDecreases number

Increases

number

Decreases

number

S90 XS/S70 XS Owner’s Manual

Setting Up

Resetting the User

Memory to the Initial

Factory Settings

The S90 XS/S70 XS has a Factory Set function for

restoring your S90 XS/S70 XS’s memory to the factory

default settings.

This lets you restore the S90 XS/S70 XS’s default

program, as well as its System and other settings.

CAUTION

When the factory settings are restored, all the data that you created in

each mode or saved to internal flash memory will be erased. Take

care so as not to lose important data. Be sure to save all important

data to a computer before executing this procedure (page 47).

1 Press the [UTILITY] button.

The Utility Select display appears.

2 Select “Fctry Set” by using the Cursor [ ]/

[ ]/[ ]/[ ] buttons, then press the [ENTER]

button.

The Factory Set display appears.

CAUTION

When setting the Auto Factory Set parameter to on and pressing the

[ ENTER] button, the Factory Set will automatically be executed each

time the power is turned on.

Keep in mind that this also means that your original data in Flash

ROM will be erased each time you turn on the power. Therefore, the

Auto Factory Set parameter should normally be set to off. When

setting the Auto Factory Set parameter to off and pressing the

[ ENTER] button, the Factory Set will not be executed when turning the

power on next time.

Please note that the setting of the Power On Auto Factory Set on this

display will be stored automatically by executing Factory Set.

3 Press the [ENTER] button to execute the

Factory Set operation.

The display prompts you for confirmation. Press the

[ENTER] button again to execute Factory Set.

After Factory Set has been completed, operation

returns to the Master Play display.

Press the [EXIT] button to cancel the Factory Set

operation.

CAUTION

For Factory Set operations that take longer to process, you will see

the message “Now executing Factory Set…” during processing.

While such a message is shown (while data is being written to Flash

ROM), never attempt to turn off the power. This means that this tone

generator may not be able to start up properly, even when turning the

power on next time.

S90 XS/S70 XS Owner’s Manual

Start Guide

There are several operation modes in the S90 XS/S70 XS, and they can be selected by using the seven mode buttons.

These modes include: Voice, Performance, Multi, Master and Sequence Play. Depending on the selected mode, you can

play and perform on the keyboard and create your own original music.

If you want to play the keyboard conventionally, use the Voice or Performance mode. If you’re creating music, particularly

multi-part arrangements, use the Multi mode.

In addition, the following modes are available: the Audio Record/Play mode for recording your keyboard performance as

audio data and playing back audio files, the File mode for managing files for saving the data you created on this

synthesizer, and the Utility mode for making overall settings.

Modes

Voice mode

[VOICE] button

This synthesizer has a wealth of high-

quality, dynamic sounds—also referred to

as “Voices.” You can play these Voices—

one Voice at a time—from the keyboard in

the Voice mode. This mode also lets you

create your own original Voices.

Playing Voices from the

keyboard

Performance mode

[PERFORM] button

This mode lets you play and create

Performances. A Performance lets you put

several different Voices together in layers or

play different two Voices in a keyboard

split.

Playing multiple Voices from

the keyboard

Master mode

[MASTER] button

This special mode lets you register and use

the programs you created in each of the

Voice, Performance, and Multi modes. The

Master mode can be used in two ways:

Storing your favorite programs

This lets you register settings that you often

use in the Voice, Performance, or Multi

mode, and instantly recall the relevant

mode and custom settings together in a

single button press—without having to first

select a mode.

Playing as a master keyboard

This lets you divide the keyboard into four

separate sections—just as if you were

playing four different MIDI keyboards.

Creating original program sets

Multi mode

[MULTI/SEQ PLAY] button

The Multi mode lets you use this instrument

as a multi-timbral tone generator for

sequencer song playback. By assigning a

different Voice to each track in a song file

on your external sequencer, you can play

back complex multi-part ensemble

recordings.

Creating an original Song via

an external sequence recorder

Sequence Play mode

[MULTI/SEQ PLAY] button

This mode lets you play back SMF files

created via an external sequencer or other

device and 44.1kHz/16-bit stereo audio

files sequentially. You can directly play

back the files stored to the internal flash

memory and saved to an external USB

storage device.

Playing back audio/MIDI files

Audio Record/Play mode

[AUDIO REC/PLAY] button

This mode lets you record your keyboard

performance to the root directory of an

external USB storage device or internal

flash memory and play back audio files

from the specified device.

Recording your performance/

playing back audio data

File mode

[FILE] button

The File mode lets you save data you've

created on this instrument to a USB storage

device or the internal flash memory, and

allows you to load data from the USB

device to the instrument. Of course, you

can store your important data to the

instrument; however, for best safe-keeping,

Yamaha recommends that you back up all

important data to a USB storage device.

Backing up data

Utility mode

[UTILITY] button

The Utility mode lets you set parameters

that apply to the entire system of this

instrument. These parameter settings are

applied to all Voices, Performances, and

Multis.

Setting the system parameters

NOTE Pressing the [MULTI/SEQ PLAY]

button toggles between the Multi

mode and Sequence Play mode.

S90 XS/S70 XS Owner’s Manual

Voices—the basic building blocks of the S90 XS/S70 XS

Voices—created in the Voice mode—are the basic sonic building blocks for the other modes of this instrument. The

Performance and Multi programs are made up of different Voices.

This instrument features an exceptionally wide variety of preset Voices for playing in virtually any musical style. Try searching

through the Voices to find your favorites. Once you’ve explored them and feel comfortable with them, try branching out

creatively and use the editing features to make your own original Voices.

Combining several Voices to create a Performance or Multi

If you want to play several different Voices together simultaneously, select a Performance. The 384 Performances are

preprogrammed and be used as such, but can also be changed and customized to suit your own needs. By using the

Performance Creator feature, you can create your own original Performance based on the Voice currently selected in the Voice

mode.

To use this instrument as a multi-timbral tone generator with computer DAW software, select a Multi. With the help of the Multis,

this instrument can be used to play back MIDI song files from a connected USB or internal flash memory device.

Master mode—create a master keyboard setup or instantly call up your desired programs

The Master mode lets you register your favorite Voices, Performances, and Multis together into easy-to-select Master programs. No

matter what mode is used—Voice, Performance or Multi—you can have it instantly and automatically selected when you call up the

appropriate Master. The Master mode can also be used to divide the keyboard into four sections—each with its own Voice—just as if

you were playing four different MIDI keyboards.

Convenient remote control of your computer DAW software

The panel of this instrument also serves as a convenient control surface for your computer music system. Use the buttons and

controllers to control the audio mixer, pan adjustment, song start/stop and the VST instrument’s parameters in your DAW

software. This highly intuitive approach gives you hands-on control over your virtual studio—a level of control that a keyboard

and mouse cannot match.

Global settings and data backup

While the Voice, Performance, and Multi modes provide controls for using and editing the programs of this instrument, the Utility

mode is the place where you make overall settings for this instrument—for example, adjusting the transpose and fine tuning

controls, or switching between MIDI and USB operation. You can also archive your important data created on this instrument to

a USB storage device for safe-keeping.

Basic Instructions

Selecting a preset Voice

page 21

Changing the tonal qualities of the Voice

page 23

Creating a new Performance in the Voice

mode by using your favorite Voices

(Performance Creator)

page 28

Selecting a Performance

page 32

Creating music using a Multi and your

computer

page 38

Playing back a MIDI file

page 41

Making Master mode settings

page 43

Remote-controlling the software

page 38

Making global system settings

page 45

Backing up important data

page 47

Sayfa yükleniyor ...

Yamaha S90 El kitabı

Marka: Yamaha

Model: S90

Kategori: Sentezleyici

Tip: El kitabı

Bu kılavuz için de uygundur

PDF İndir

rapor

Diğer dillerde

español: Yamaha S90 El manual del propietario
français: Yamaha S90 Le manuel du propriétaire
italiano: Yamaha S90 Manuale del proprietario
svenska: Yamaha S90 Bruksanvisning
čeština: Yamaha S90 Návod k obsluze
polski: Yamaha S90 Instrukcja obsługi
Deutsch: Yamaha S90 Bedienungsanleitung
português: Yamaha S90 Manual do proprietário
English: Yamaha S90 Owner's manual
dansk: Yamaha S90 Brugervejledning
русский: Yamaha S90 Инструкция по применению
suomi: Yamaha S90 Omistajan opas
Nederlands: Yamaha S90 de handleiding
română: Yamaha S90 Manualul proprietarului

Yamaha S90 El kitabı

Bu kılavuz için de uygundur

Yamaha S90 El kitabı

Diğer dillerde

İlgili Makaleler