Dell PowerVault MD3000i Hızlı başlangıç Kılavuzu

FILE LOCATION: J:\DL\DL102196\DTP\UW791fc1.fm

DELL CONFIDENTIAL – PRELIMINARY 4/30/10 – FOR PROOF ONLY

Current template as of 4/26/2007

Model AMP01

Getting Started

With Your System

Začínáme se systémem

Guide de mise en route

Erste Schritte mit dem System

Τα πρώτα βήματα με το σύστημά σας

Rozpoczęcie pracy z systemem

Начало работы с системой

Procedimientos iniciales con el sistema

Sistem Başlangıç Kılavuzu

תכרעמה םע הדובעה תליחת

FILE LOCATION: J:\DL\DL102196\DTP\UW791et1.fm

DELL CONFIDENTIAL – PRELIMINARY 4/23/10 – FOR PROOF ONLY

Model AMP01

Getting Started

With Your System

FILE LOCATION: J:\DL\DL102196\DTP\UW791et1.fm

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use

of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data

and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury,

or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly

forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerVault, and Dell OpenManage are trademarks

of Dell Inc.; Microsoft, Windows, and Windows Server are either registered trademarks or trademarks

of Microsoft Corporation in the United States and/or other countries; SUSE and NetWare are registered

trademarks of Novell, Inc., in the United States and other countries; Red Hat and Enterprise Linux are

registered trademarks of Red Hat, Inc.; Intel and Intel XScale are registered trademarks of Intel

Corporation in the U.S. and other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Model AMP01

April 2010 P/N UW791 Rev. A01

Getting Started With Your System 3

System Features

This section describes the major hardware and software features of your

system. It also provides information about other documents you may need

when setting up your system and how to obtain technical assistance.

Performance Features

• 667-MHz Intel

®

XScale

®

processor

• 512-MB high-speed data cache memory

Scalability Features

• Capacity for 15 1-inch, hot-plug, 3.0-Gbps, serial-attached SCSI (SAS)

physical disks.

• Support for up to two daisy-chained storage enclosures for a total

of 45 physical disks.

• Controller capable of supporting sessions from 32 iSCSI initiators

(16 hosts with redundant connections) simultaneously with multiple

connections per session. For more information, refer to the

Dell

PowerVault MD Systems Support Matrix

at

support.dell.com

.

• Support for a wide range of servers. (For additional support information,

refer to the

Dell PowerVault MD Systems Support Matrix

at

support.dell.com

).

• Support for both simplex (single controller) and duplex (dual controller)

array configurations.

Availability Features

• Up to two active/active RAID controller modules (duplex configuration)

for redundant data and system management capability; simplex

configuration also available

• Battery backup unit (BBU) to power the RAID controller system memory

(cache) for a minimum of 72 hours in case of a power outage

• Redundant hot-plug power supply and cooling modules that are combined

for easy serviceability

4 Getting Started With Your System

Manageability and Serviceability Features

• Efficient rack-mount designed storage system

• Hot-pluggable drives

• Four sensors for monitoring ambient temperatures

• Over-temperature shutdown protection capability

• Configuration and monitoring via the MD Storage Manager software

Supported Operating Systems

Your system supports the following operating systems:

• Microsoft

®

Windows

®

Storage Server 2003 R2

• Microsoft Windows Server

®

2003 R2 Standard and Enterprise Editions

• Microsoft Windows Server 2003 Service Pack 1(SP1) with patches

• Microsoft Windows Server 2003 Service Pack 2 (SP2)

• Microsoft Windows Server XP Professional SP2 (management station only,

no I/0 attach)

•Red Hat

®

Enterprise Linux

®

V4.0 with Update 4 (AS, ES, WS), 32 bit

and 64 bit (2.6 kernel)

•SUSE

®

Linux Enterprise Server V9.0 service pack 3 with Intel

EM64T(2.6 kernel)

For more information, refer to the

Dell PowerVault MD Systems Support Matrix

at

support.dell.com

.

Other Information You May Need

CAUTION: The Product Information Guide provides important safety and

regulatory information. Warranty information may be included within this

document or as a separate document.

•The

Rack Installation Instructions

included with your rack solution

describes how to install your system into a rack.

•The

Hardware Owner’s Manual

provides information about system

features and describes how to troubleshoot the system and install or

replace system components. This document can be found on the CDs

that came with your system or at

support.dell.com

.

Getting Started With Your System 5

• CDs included with your system provide documentation and tools for

installing, configuring, and managing your system.

• The

Dell PowerVault MD Systems Support Matrix

at

support.dell.com

provides compatibility information, including servers, operating systems,

controllers, software, and hardware configurations.

• Updates are sometimes included with the system to describe changes

to the system, software, and/or documentation.

NOTE: Always check for updates on support.dell.com and read the updates

first because they often supersede information in other documents.

• Release notes or readme files may be included to provide current updates

to the system or documentation or advanced technical reference material

intended for experienced users or technicians.

Obtaining Technical Assistance

If you do not understand a procedure in this guide or if the system does

not perform as expected, see your Hardware Owner’s Manual.

Dell Enterprise Training and Certification is available; see

www.dell.com/training for more information. This service may not be offered

in all locations.

Installation

CAUTION: Before performing the following procedure, read and follow the safety

instructions and important regulatory information in your Product Information

Guide.

This section describes the steps to set up your system for the first time.

For more detailed information, refer to the Installation Guide provided

on the CDs that came with your system.

Unpack the System

Unpack your system and identify each item. Keep all shipping materials

in case you need them later.

6 Getting Started With Your System

Install the Rails and System in a Rack

Install the rails and system in the rack once you have read the "Safety

Instructions" located in the rack installation documentation for your system.

See your rack installation documentation for instructions on installing your

system in a rack.

Getting Started With Your System 7

Connect the Power Cables and Power Cord Retention Bracket

Connect both power cables to the power supply/cooling fan modules.

Attach the power cord retention bracket to the power supply loop by affixing

the back clasp of the bracket to the top of the loop and the middle clasp to

the vertical middle of the loop. Attach the system power cable to the bracket’s

cable clasp. Repeat the procedure for the second power supply.

8 Getting Started With Your System

Plug the other end of the power cables into a grounded electrical outlet

or a separate power source such as

an uninterruptible po

wer supply (UPS)

or a power distribution unit (PDU).

Cable the RAID controller modules according to the instructions provided

in the

Hardware Owner’s Manual

.

Getting Started With Your System 9

Turn on the System

Turn on the system by turning on both power supply/cooling fan modules.

If you have purchased the optional system bezel, install it after turning on

the system. Insert the right edge of the bezel into the right front loop on the

system, and then press the left edge of the bezel to the system until the bezel

snaps into place.

10 Getting Started With Your System

Specifications

Disks

Physical disks Up to 15 1-inch-by-3.5-inch SAS hot-plug

physical disks (3.0 Gbps). (See your

system readme file for supported disk

capacities.)

RAID Controller Modules

iSCSI RAID controllers

• Two hot-pluggable active/active

controllers (or one controller in simplex

mode)

• 512 MB of cache per controller

• Simplex or duplex configurations

• One temperature sensor per controller

RAID Controller Back-Panel Connectors

iSCSI ports (per RAID controller)

• One 100/1000 BASE-T iSCSI Port 0 "In"

connector for connecting hosts

• One 100/1000 BASE-T iSCSI Port 1 "In"

connector for connecting additional

hosts

SAS expansion port

(per RAID controller)

One 3.0 Gbps SAS Port "Out" connector

for expansion to an additional enclosure

Debug connector

(per RAID controller)

One 6-pin mini-DIN connector

Management port

(per RAID controller)

One 10/100 BASE-T connection for out-

of-band management of the enclosure

Getting Started With Your System 11

Backplane Board

Connectors

• 15 SAS physical-disk connectors

• Two power supply/cooling fan module

connectors

• Two sets of RAID controller connectors

(six connectors each controller)

• One control panel connector for front

LEDs

Sensors Two temperature sensors

LED Indicators

Front panel

• One two-color LED indicator for system

status

• Two single-color LED indicators

(one for power; one nonfunctional)

Physical disk carrier

• One single-color activity LED

• One two-color LED status indicator

per disk

RAID controller The following single-color LEDs:

• Battery fault

• Cache active

• Controller fault

• Controller power

• Ethernet link

• Ethernet activity

• SAS Out fault/active

• iSCSI In fault (2)

• iSCSI In active (2)

Power supply/cooling fan module Three LED status indicators for power

supply status, power supply/fan fault,

and AC status

12 Getting Started With Your System

Power Supplies

Wattage 488 W maximum continuous; 550 W

peak

Voltage 100–240 V rated (actual 90–264 V)

Frequency 47–63 Hz

Amperage 7.2 A at 100 V, 3.6 A at 200 V

Available Physical Disk Power (Per Slot)

Supported physical-disk power

consumption

up to 1.3 A at +12 V

up to 1.5 A at +5 V

Physical

Height 13.11 cm (5.16 in)

Width 44.63 cm (17.57 in)

Depth 48.01 cm (18.9 in)

Weight (maximum configuration) 35.37 kg (78 lb)

Environmental (Enclosure)

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets

Temperature

Operating

10° to 35°C (50° to 95°F)

Storage

–40° to 65°C (–40° to 149°F)

Relative humidity

Operating

5% to 80% (noncondensing)

Storage

5% to 95% (noncondensing)

Altitude

Operating

–16 to 3048 m (–50 to 10,000 ft)

Storage

–16 to 10,600 m (–50 to 35,000 ft)

BTU per hour 1430 (maximum)

Getting Started With Your System 13

Environmental (Battery Backup Unit [BBU])

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets

Maximum input power

• +12 VDC +/–5% at 1 A

• +3.3 VDC +/–5% at 150 mA

• Operating temperature range: 5° to

35°C (41° to 95°F)

Regulated output voltage from BBU

• +2.5 VDC +/–3% at 20 mA to 120 mA

• Operating temperature range: 5° to

45°C (41° to 113°F)

Minimum retention time (life

expectancy)

72 hours for 512-MB DDR-I DIMM,

2.5 V at 120 mA

Working temperature range (dry bulb)

• 5° to 35°C (41° to 95°F)

• Maximum dry bulb temperature

derated by 3.3°C (37.9°F) per 1000 m

(3281 ft) above 500 m (1640 ft)

Working relative humidity range 5% to 90% noncondensing

Storage temperature range (dry bulb)

• –10° to 45°C (14° to 113°F) for

3 months maximum

• Maximum dry bulb temperature

derated by 3.3°C (37.9°F, guaranteed)

per 1000 m (3281 ft) above 500 m

(1640 ft)

Transit temperature range (dry bulb) –20° to 60°C (–4° to 140°F) for 1 week

maximum

Storage and transit humidity range 5% to 95% relative humidity

Storage and transit maximum

temperature gradient

1°C (33.8°F) per minute to a maximum

of 20°C (68°F) per hour

Storage and transit maximum humidity

gradient

30% relative humidity per hour

14 Getting Started With Your System

FILE LOCATION: J:\DL\DL102196\DTP\UW791zt1.fm

DELL CONFIDENTIAL – PRELIMINARY 4/23/10 – FOR PROOF ONLY

Model AMP01

Začínáme

se systémem

FILE LOCATION: J:\DL\DL102196\DTP\UW791zt1.fm

Poznámky a upozornění

POZNÁMKA: POZNÁMKA označuje důležitou informaci, s jejíž pomocí

lépe využijete svůj počítač.

UPOZORNĚNÍ: UPOZORNĚNÍ poukazuje na možnost poškození

hardwaru nebo ztráty dat a poskytuje návod, jak se danému problému

vyhnout.

POZOR: Výstraha („POZOR“) poukazuje na riziko poškození

majetku, poranění nebo smrtelného úrazu.

____________________

Informace obsažené v tomto dokumentu podléhají změnám bez předchozího upozornění.

Reprodukce jakýmkoli způsobem bez písemného povolení společnosti Dell Inc. je přísně zakázána.

Obchodní známky použité v tomto textu: Dell, logo DELL, PowerVault a Dell OpenManage jsou

obchodní známky společnosti Dell Inc.; Microsoft, Windows a Windows Server jsou registrované

obchodní známky nebo obchodní známky společnosti Microsoft Corporation ve Spojených státech

amerických a/nebo dalších zemích; SUSE a NetWare jsou registrované obchodní známky společnosti

Novell, Inc. ve Spojených státech amerických a dalších zemích; Red Hat a Enterprise Linux jsou

registrované obchodní známky společnosti Red Hat, Inc.; Intel a Intel XScale jsou registrované

obchodní známky společnosti Intel Corporation ve Spojených státech amerických a dalších zemích.

V tomto dokumentu mohou být použity další obchodní známky a názvy odkazující na subjekty,

kterým tyto známky či názvy patří, nebo na jejich výrobky. Společnost Dell Inc. se zříká jakýchkoli

vlastnických zájmů o jiné než vlastní ochranné známky a obchodní názvy.

Model AMP01

Duben 2010 Č. dílu UW791 Rev. A01

Začínáme se systémem 17

Systémové funkce

V této části jsou popsány hlavní hardwarové a softwarové funkce vašeho systému.

Jsou v ní obsaženy i informace o doplňujících dokumentech, které příp.

potřebujete při instalaci systému, a informace k odborné pomoci.

Výkon

•

667 MHz Intel

®

XScale

®

procesor

•

512 MB vysokorychlostní datové cache paměti

Rozšiřitelnost

•

Kapacita pro 15 sériově propojených SCSI (SAS) pevných disků,

1x3,5 palce, hot-plug, 3,0 Gb/s.

•

Podpora až dvou zřetězených ukládacích svazků pro celkem 45 pevných disků.

•

Řadič podporující až 32 relací iSCSI iniciátorů (16 hostitelů s redundantními

spojeními) současně s násobnými spojeními na jednu relaci. Pro více

informací nahlédněte do

Dell PowerVault MD Systems Support Matrix

na adrese

support.dell.com

.

•

Podpora širokého spektra serverů. (Pro více informací o podporovaných

systémech nahlédněte do

Dell PowerVault MD Systems Support Matrix

na adrese

support.dell.com

).

•

Podpora simplexní (jeden řadič) i duplexní (duální řadič) konfigurace polí.

Dostupnost

•

Až dva aktivní/aktivní moduly RAID řadičů (duplexní konfigurace)

umožňující správu záložních dat a systému; simplexní konfigurace rovněž

k dispozici.

•

Záložní napájecí zdroj pro zajištění napájení paměti systému RAID řadiče

(cache) v případě výpadku napětí po dobu min. 72 hodin.

•

Záložní hot-plug napájecí zdroj a kombinované chladicí moduly pro snadnou

údržbu.

18 Začínáme se systémem

Správa a servis

•

Úložný systém v účelně řešené konzolové konstrukci

•

Disky vyměnitelné za provozu

•

Čtyři senzory pro sledování okolní provozní teploty

•

Ochranná funkce vypnutí při přehřátí

•

Konfigurace a monitorování prostřednictvím softwaru MD Storage Manager

Podporované operační systémy

Váš systém podporuje následující operační systémy:

•

Microsoft

®

Windows

®

Storage Server 2003 R2

•

Microsoft Windows Server

®

2003 R2 Standard a Enterprise Editions

•

Microsoft Windows Server 2003 Service Pack 1 (SP1) se záplatami (patches)

•

Microsoft Windows Server 2003 Service Pack 2 (SP2)

•

Microsoft Windows Server XP Professional SP2 (pouze správc. stanice,

bez připojených I/0)

•

Red Hat

®

Enterprise Linux

®

V4.0 s aktualizací 4 (AS, ES, WS), 32 bit

a 64 bit (2.6 kernel)

•

SUSE

®

Linux Enterprise Server V9.0 service pack 3 s Intel

EM64T(2.6 kernel)

Pro více informací nahlédněte do

Dell PowerVault MD Systems Support Matrix

na adrese

support.dell.com

.

Sayfa yükleniyor ...

Dell PowerVault MD3000i Hızlı başlangıç Kılavuzu

Dell PowerVault MD3000i Hızlı başlangıç Kılavuzu

Diğer dillerde

İlgili Makaleler

Dell PowerVault MD3000i Hızlı başlangıç ​​Kılavuzu

Dell PowerVault MD3000i Hızlı başlangıç ​​Kılavuzu

Diğer dillerde

İlgili Makaleler

Dell PowerVault MD3000i Hızlı başlangıç Kılavuzu

Dell PowerVault MD3000i Hızlı başlangıç Kılavuzu