Indesit DFG 26B10 NX EU Kullanici rehberi

Kategori
Bulaşık makineleri
Tip
Kullanici rehberi
Operating instructions
Contents
Product Fiche, 2
Precautions and advice, 3
General safety
Disposal
Saving energy and respecting the environment
Installation and Assistance, 4-5
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Assistance
Description of the appliance, 6
Overall view
Control panel
Loading the racks, 7-8
Lower rack
Cutlery basket
Upper rack
Adjusting the upper rack
Start-up and use, 9
Starting the dishwasher
Measuring out the detergent
Wash cycles, 10
Table of wash cycles
Special wash cycles and Options, 11
Rinse aid and refined salt, 12
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 13
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Troubleshooting, 14
English,1
EN
DFG 26B10
DISHWASHER
TR
Türkçe, 15
EN
2
Product Fiche
Brand
INDESIT
Model
DFG 26B10
Rated capacity in standard place settings (1)
13
Energy efciency class on a scale from A+++ (low consumption) to D (high consumption)
A+
Energy consumption per year in kWh (2)
295.0
Energy consumption of the standard cleaning cycle in kWh
1.04
Power consumption of the off-mode in W
0.5
Power consumption of the left-on mode in W
5.0
Water consumption per year in litres (3)
3080.0
Drying efcacy class on a scale from G (low efcacy) to A (high efcacy)
A
Programme time for standard cleaning cycle in minutes
190
The duration of the left-on mode in minutes
10
Noise in dB(A) Re 1pW
51
Built-in model
NO
NOTES
1) The information on the label and che relates to the standard cleaning cycle, this programme is suitable to clean normally
soiled tableware and it is the most efcient programme in terms of combined energy and water consumption. The standard
cleaning cycle corresponds to the Eco cycle.
2) Based on 280 standard cleaning cycles using cold water ll and the consumption of the low power modes. Actual energy
consumption depends on how the appliance is used.
3) Based on 280 standard cleaning cycles. Actual water consumption depends on how the appliance is used.
Product fiche
EN
3
* Only available in selected models.
This appliance was designed and manufactured
in compliance with international safety standards
The following information has been provided for
safety reasons and should therefore be read
carefully.
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or
moved, please ensure the manual is kept with the
machine.
Please read these instructions carefully: they contain
important information on installation, use and safety.
This appliance is designed for domestic use or
similar applications, for example:
- staff kitchen areas in shops, offices and other work
environments;
- farmhouses;
- use by guests in hotels, motels and other residential
settings;
- bed & breakfasts.
General safety
• Theapplianceshouldnotbeoperatedbypeople
(including children) with reduced physical,
sensory or mental capacities, or by inexperienced
people who are not familiar with the product,
unless supervision or instructions on how to
use it are provided by someone who assumes
responsibility for their safety.
• Anadultmustsupervisechildrenatalltimesto
prevent them from playing with the appliance.
The appliance was designed for domestic
use inside the home and is not intended for
commercial or industrial use.
• The appliance must be used by adults onlyto
wash domestic crockery in accordance with the
instructions in this manual.
• The appliance must not be installed outdoors,
even in covered areas. It is extremely dangerous
to leave the machine exposed to rain and storms.
• Donottouchtheappliancewhenbarefoot.
• Whenunpluggingtheappliancealwayspullthe
plug from the mains socket. Do not pull on the
cable.
• Thewatersupplytapmustbeshutoffandthe
plug should be removed from the electrical socket
before cleaning or maintaining the appliance.
• Iftheappliancebreaksdown,donotunderany
circumstances touch the internal parts in an
attempt to perform the repair work yourself.
Do not lean or sit on the open door of the
appliance: this may cause the appliance to
overturn.
•Thedoorshouldnotbeleftopenasitmaycreate
a dangerous obstacle.
• Keep detergent and rinse aid out of reach of
children.
• Thepackagingmaterialshouldnotbeusedasa
toy for children.
Disposal
• Disposal of packaging material: observe local
legislation so that the packaging may be reused.
The European Directive 2012/19/EU relating
to Waste Electrical and Electronic Equipment
(WEEE) states that household appliances should
not be disposed of using the normal solid urban
waste cycle. Exhausted appliances should be
collected separately in order to optimise the re-
using and recycling rate of the materials inside the
machine, while preventing potential damage to
the environment and public health. The crossed-
out dustbin symbol is marked on all products to
remind the owners of their obligations regarding
separated waste collection.
For further information relating to the correct
disposal of household appliances, owners may
contact the relevant public authority or the local
appliance dealer.
Saving energy and respecting the
environment
Saving water and energy
• Onlybeginawashcyclewhenthedishwasheris
full.Whilewaitingforthedishwashertobefilled,
prevent unpleasant odours using the Soak cycle
(seeWashcycles)
.
• Selectawashcyclethatissuitedtothetypeof
crockery and to the soil level of the crockery using
the Table of wash cycles:
-fordisheswithanormalsoillevelusetheEco
wash cycle, which ensures low energy/water
consumption levels.
- If the load is smaller than usual activate the Half
Load option*
(see Start-up and use).
• Ifyourelectricitysupplycontractgivesdetailsof
electricity-saving time bands, run wash cycles
when electricity prices are lower. The Delayed
Start button *
(see Start-up and use)
helps you
organise the wash cycles accordingly.
Phosphate-free and chlorine-free detergents
containing enzymes
• Westronglyrecommendthatyouusedetergents
that do not contain phosphates or chlorine, as
these products are harmful to the environment.
• Enzymesprovideaparticularlyeffectiveactionat
temperaturesaround50°C.Asaresultdetergents
containingenzymescanbeusedinconjunction
with low-temperature wash cycles in order to
achievethesameresultsasanormal65°Cwash
cycle.
•Toavoidwastingdetergent,usetheproductin
appropriatequantitiesbasedonthemanufacturer’s
recommendations, the hardness of the water,
the soil level and the quantity of crockery to
be washed. Even if they are biodegradable,
detergents contain substances which may alter
the balance of nature.
Precautions and advice
EN
4
Installation and Assistance
* Only available in selected models.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
Positioning and levelling
1.Remove the appliancefrom all packagingand check that
it has not been damaged during transportation. If it has been
damaged, contact the retailer and do not proceed any further
with the installation process.
2.Arrangethedishwashersothatitssidesorbackpanelarein
contact with the adjacent cabinets or the wall. This appliance
can also be recessed under a single worktop
*
(see the Assembly
Instruction sheet.)
3. Position the dishwasher on a level sturdy floor. If the floor
is uneven, the front feet of the appliance should be adjusted
untilitreachesahorizontalposition.Iftheapplianceislevelled
correctly, it will be more stable and much less likely to move or
cause vibrations and noise while it is operating.
4
*. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in a clockwise direction to increase the height and in an
anticlockwise direction to decrease it
(see Building-in Instruction
sheet attached to the documentation.)
Connecting the water and electricity supplies
Connection to the water and electricity supplies should only
beperformedbyaqualifiedtechnician.
The dishwasher should not stand on the water hoses or
electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Never use old or second hand hose sets. Do not reuse hose
sets from any previously installed dishwasher.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
Connecting the water inlet hose
• Toasuitablecoldwaterconnectionpoint:beforeattaching
the hose, run the water until it is perfectly clear so that any
impurities that may be present in the water do not clog the
appliance; after performing this operation, screw the inlet
hose tightly onto a tap with a ¾ gas threaded connection.
• Toasuitablehotwaterconnectionpoint:yourdishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
doesnotexceedatemperatureof60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician
(see Assistance.)
The water pressure must be within the values indicated in
the Technical Data table
(see adjacent information.)
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct with
a minimum diameter of 4 cm.
Theoutlethosemustbeataheightrangingfrom40to80cm
fromthefloor/surfacewherethedishwasherrests(A).
Before connecting the water outlet hose to the sink drain, remove
the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Somemodelsarealsoequippedwiththesupplementarysafety
device New Acqua Stop*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstances should the water inlet hose be cut, as
it contains live electrical parts.
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
• Thesocketisearthedandcomplieswithcurrentregulations.
• thesocketcanwithstandthemaximumloadoftheappliance,
which is indicated on the data plate located on the inside of
the door
(see Description of the appliance);
• Thepowersupplyvoltagefallswithinthevaluesindicatedon
the data plate on the inside of the door.
• Thesocketiscompatiblewiththeplugoftheappliance.If
this is not the case, ask an authorised technician to replace
the plug (
see Assistance
); do not use extension cables or
multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order
topreventallpotentialhazards
(see Assistance.)
EN
5
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.
Advice regarding the first wash cycle
After the installation, remove the stoppers from the racks and the
retaining elastic elements from the upper rack, if any.
Immediately before the fist washing,
completely fill the salt
dispenser with water and add only then approximately 1
kg of salt
(seechapterentitledRinseaidandrefinedsalt)
.
The water may overflow: this is normal and is not a cause
for concern. Select the water hardness value
(see chapter
entitledRinseaidandrefinedsalt).
- After the salt has been
poured into the machine, the LOW SALT indicator light*
switches off.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 13 standard place-settings
Water supply pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply voltage See appliance data plate
Total absorbed power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC (Labelling)
-2012/19/EU Waste Electrical
and Electronic Equipment
(WEEE)
The machine has a buzzer/set of tones
(depending on the
dishwasher model
) to inform the user that a command has
been implemented: power on, cycle end etc. *
The symbols/indicator lights/LEDs on the control panel/
display may vary in colour and may have a flashing or fixed
light
(depending on the dishwasher model)
.
The display* provides useful information concerning the
type of wash cycle, drying/wash-cycle phase, remaining
time, temperature etc etc.
* Only available in selected models.
Assistance
Before contacting Assistance:
• Checkwhethertheproblemcanberesolvedusingthe
Troubleshooting guide
(see Troubleshooting).
• Restarttheprogrammetocheckwhethertheproblem
has ceased to exist.
If the problem persists, contact the Authorised
Technical Assistance Service.
Never use the services of unauthorised technicians.
Please have the following information to hand:
• Thetypeofmalfunction.
• Theappliancemodel(Mod.).
• Theserialnumber(S/N).
This information can be found on the appliance data plate
(see Description of the appliance)
.
EN
6
Overall view
Description of the
appliance
***Only in completely built-in models.
* Only available in selected models.
The number and type of wash cycles and options may vary depending on the dishwasher model.
1. Upper rack
2. Upper sprayer arm
3. Tip-up dispensers
4. Rackheightadjuster
5. Lower rack
6. Lower sprayer arm
7. Washingfilter
8. Salt dispenser
9. Detergent dispenser, rinse-aid dispenser and
Active Oxygen device*
10. Data plate
11. Control panel***
Control panel
Start/Pause button and
indicator light
ON/OFF/Reset button
Cycle select knob
Indicator light Low Salt
Delayed Start button
and indicator light
Indicator light
Low Rinse Aid
Half load button and indicator light
Indicator light Washing and Delayed Start 3h.
Indicator light Drying and Delayed Start 6h.
Indicator light Wash Cycle End and Delayed Start 9h.
EN
7
Loading the racks
Tips
Before loading the racks, remove all food residues from the
crockeryandemptyliquidsfromglassesand containers. No
preventive rinsing is needed under running water.
Arrange the crockery so that it is held in place firmly and does
not tip over; and arrange the containers with the openings facing
downwards and the concave/convex parts placed obliquely,
thus allowing the water to reach every surface and flow freely.
Make sure that the lids, handles, trays and frying pans do not
prevent the sprayer arms from rotating. Place any small items
in the cutlery basket.
Since plastic dishes and non-stick frying pans usually retain more
water drops, their drying will be not so good as that of ceramic
or stainless-steel dishes.
Lightweight items such as plastic containers should be placed
in the upper rack and arranged so that they cannot move.
After loading the appliance, make sure that the sprayer arms
can rotate freely.
Lower rack
The lower rack can hold pans, lids, dishes, salad bowls, cutlery
etc. Large plates and lids should ideally be placed at the sides.
Very soiled dishes and pans should be placed in the lower rack
because in this sector the water sprays are stronger and allow
a higher washing performance.
Several dishwasher models are fitted with tip-up sectors
*.
They can be used in a vertical position when arranging dishes
orinahorizontalposition(lower)toloadpansandsaladbowls
easily.
Cutlery basket
The basket is equipped with top grilles for improved cutlery
arrangement. The cutlery basket should be positioned only at
the front of the lower rack
Knives and other utensils with sharp edges must be placed
in the cutlery basket with the points facing downwards or they
mustbepositionedhorizontallyinthetip-upcompartmentson
the upper rack
Upper rack
Load this rack with delicate and lightweight crockery such as
glasses, cups, saucers and shallow salad bowls.
Several dishwasher models are fitted with tip-up sectors
*.
They can be used in a vertical position when arranging tea/
dessert saucers or in a lower position to load bowls and food
containers.
*Only available in selected models with different numbers and
positions.
EN
8
* Only available in selected models.
Adjusting the height of the upper rack
In order to make it easier to arrange the crockery, the upper rack
may be moved to a higher or lower position.
The height of the upper rack should be adjusted WHEN THE
RACK IS EMPTY.
NEVER raise or lower the rack on one side only.
IftherackisequippedwithaLift-Up device*
(see figure)
, lift
it up by holding its sides. To restore the lower position, press
the levers (A) at the sides of the rack and follow the rack down.
Unsuitable crockery
• Woodencrockeryandcutlery.
• Delicatedecoratedglasses,artistichandicraftandantique
crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high
temperatures.
• Copperandtincrockery.
• Crockerysoiledwithash,wax,lubricatinggreaseorink.
Thecoloursofglassdecorationsandaluminium/silverpiecescan
change and fade during the washing process. Some types of
glass(e.g.crystalobjects)canbecomeopaqueafteranumber
of wash cycles too.
Damage to glass and crockery
Caused by:
• Typeofglassandglassproductionprocess.
• Chemicalcompositionofdetergent.
• Watertemperatureofrinsecycle.
Tips:
Only use glasses and porcelain guaranteed by the
manufacturer as dishwasher safe.
• Useadelicatedetergentsuitableforcrockery.
• Collectglassesandcutleryfromthedishwasherassoonas
the wash cycle is over.
Theupperrackcanbeadjustedforheightbasedonrequirements:
high position to place bulky crockery in the lower rack and low
positiontomakethemostofthetip-upcompartments/sectors
by creating more space upwards.
Tip-up compartments with adjustable position
The side tip-up compartments can be positioned at three
differentheightstooptimizethearrangementofcrockeryinside
the rack.
Wineglassescanbeplacedsafelyinthetip-upcompartments
by inserting the stem of each glass into the corresponding slots.
Cutlery tray*
Some dishwasher models are fitted with a sliding tray which
can be used to hold serving utensils or small cups. For
optimum washing performance, avoid positioning bulky
crockery directly below the tray.
The cutlery tray can be removed
(see Figure).
Before loading the tray, make
sure the supports are prop-
erly coupled to the upper rack
(see Figure).
EN
9
Start-up and use
* Only available in selected models.
Measuring out the detergent
A good wash result also depends on the correct
amount of detergent being used. Exceeding the stated
amount does not result in a more effective wash and
increases environmental pollution.
Based on how soiled the items are, the amount can be
adjusted to individual cases using powder or liquid
detergent.
In the case of normally soiled items, use approximately
either 35 gr (powder detergent) or 35 ml (liquid detergent).
If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce
the amount of detergent used accordingly.
For good washing results also follow the instructions shown
on the detergent box.
For further questions please ask the detergent producers'
Advice Offices.
To open the detergent dispenser use the opening device “A”.
Introduce the detergent into the dry dispenser “B” only.
Place the amount of detergent for pre-washing directly
inside the tub.
1.
WhenmeasuringoutthedetergentrefertotheTableofwash
cyclestoaddtheproperquantity.CompartmentB comprises
a level showing the maximum quantity of liquid or powder
detergent that can be added to each cycle.
2.
Removedetergentresiduesfromtheedgesofthedispenser
and close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the wash cycle.
If all-in-one detergents are used, we recommend using the TABS
option, because it adjusts the cycle so that the best washing
and drying results are always achieved.
Only use detergent which has been specifically designed
for dishwashers.
DO NOT USE washing-up liquid.
Using excessive detergent may result in foam residue
remaining in the machine after the cycle has ended.
The use of tablets is only recommended for models which
offer the MULTI-FUNCTIONAL TABLETS option.
To achieve the best results from each washing and drying
cycle, powder detergent, liquid rinse aid and salt should
be used.
Starting the dishwasher
1.Turnthewatertapon.
2.SwitchontheappliancebypressingtheON/OFFbutton.
3. Open the door and pour in a suitable amount of detergent
(see Measuring out the detergent).
4. Load the racks
(see Loading the racks)
and shut the door.
5.SelectthewashcyclebyturningtheSELECTWASHCYCLE
knob: align the notch on the knob with the number or symbol
representing the desired wash cycle. The START/PAUSE
indicator light will go on.
6. Select the wash options
*
(see Options and Special Wash
Cycles).
7.StartthecyclebypressingtheSTARTbutton;theindicator
light will stop flashing and stay lit (fixed light). The indicator light
corresponding to the wash phase will go on, signalling that the
wash cycle has begun.
8.AttheendofthewashcycletheENDindicatorlightwillgoon
(fixedlight).SwitchofftheappliancebypressingtheON/OFF
button, shut off the water tap and unplug the appliance from
the electricity socket.
9.Waitafewminutes before removing thecrockerytoavoid
getting burnt. Unload the racks, beginning with the lower level.
- The machine will switch off automatically during long
periods of inactivity in order to minimise electricity
consumption.
Changing a wash cycle in progress
If a mistake was made in the wash-cycle selection process, it is
possible to change the cycle provided that it has only just begun:
once the wash cycle has started, in order to change the wash
cycleswitchoffthemachinebypressingandholdingtheON/
OFF/Resetbutton.Switchitbackonusingthesamebuttonand
select the desired wash cycle and options.
Adding extra crockery
PresstheStart/Pausebuttonandopenthedoor,takingcareto
avoid the escaping steam, and place the crockery inside the
dishwasher.PresstheStart/Pausebutton:Thecyclewillstart
again after a long beep has been emitted.
If the delayed start has been set, at the end of the countdown
the wash cycle will not start. It will stay in Pause mode.
PresstheStart/Pausebuttontopausethemachine;thewash
cycle is stopped.
At this stage the wash cycle cannot be changed.
Accidental interruptions
If the door is opened during the wash cycle or there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply restored.
EN
10
Wash cycles
The number and type of wash cycles and options may vary depending on the dishwasher model.
Wash-cycledataismeasuredunderlaboratoryconditionsaccordingtoEuropeanStandardEN50242.
Based on the different conditions of use, the wash-cycle duration and data can change.
Wash Cycle Drying Options
Wash Cycle
Duration
Water
Consumption (l/
cycle)
Energy
Consumption
(kWh/cycle)
1. Eco Yes
Half Load - Delayed Start
03:10’
11,0 1,04
2. Intensive Yes
Half Load - Delayed Start
02:30’
16,5 1,70
3. Normal Yes
Half Load - Delayed Start
02:00’
16,0 1,35
4. Delicates Yes
Half Load - Delayed Start
01:30’
12,0 1,10
5. Rapid 40’ No
Delayed Start
00:40’
9,0 0,95
6. Prewash No
Half Load - Delayed Start
00:10’
4,0 0,01
Instructions on wash-cycle selection and detergent dosage
1. TheECOwashcycleisthestandardcycletowhichtheenergylabeldatarefers.Itcanbeusedtowashcrockerywithanormal
soil level and is the most efficient cycle in terms of energy and water consumption for this type of crockery.
27gr/ml+6gr/ml**–1Tab
(**Quantity of pre-washing detergent)
2. Heavilysoileddishesandpans(nottobeusedfordelicateitems).30gr/ml–1Tab
3.Normallysoiledpansanddishes.27gr/ml+6gr/ml**–1Tab
4. Economicandfastwashfordelicateitemswhicharesensitivetohightemperatures.30gr/ml–1Tab
5.Fastcycletobeusedforslightlydirtydishes(idealfor2placesettings)25gr/ml–1Tab
6. Pre-wash while awaiting completion of the load with the dishes from the next meal. No detergent.
Standbyconsumption:Left-onmodeconsumption:5,0W-Offmodeconsumption:0.5W
EN
11
Delayed start
It is possible to delay the start time of the wash cycle
by 3, 6 or 9 hours:
1:After selecting the desired wash cycle and any other
options, press the DELAYED START button. the indicator
light will go on.
2:Selectthe desireddelaytime bypressingthe Delayed
Start button repeatedly. The wash phase (3 hours), drying
phase(6hours)andend(9hours)indicatorlightswillgoon
in succession.
If the Delayed Start button is pressed again, the option is
deselected and the indicator light goes off.
3. After the selection process, the countdown will begin if
theStart/Pausebuttonispressed.Theselecteddelay-period
indicator light flashes and the Start/Pause button stops
flashing (fixed light).
3.Oncethistimehaselapsed,theDELAYEDSTARTindicator
light goes off and the wash cycle begins.
The Delayed Start function cannot be set once a wash
cycle has started.
Wash options*
The OPTIONS may only be set, changed or reset after
the wash cycle has been selected and before the Start/
Pause button has been pressed.
Only the options which are compatible with the type of wash
cycle set may be selected. If an option is not compatible
with the selected wash cycle
(see Table of wash cycles)
, the
correspondingsymbol/LEDflashesrapidly3times.
If an option is selected which is not compatible with another
previously-selected option, it will flash 3 times and go off,
while the most recently selected option will remain active.
To deselect an option which has been set by mistake, press
the corresponding button again.
Notes:
Optimum performance levels when using the “"Rapid” cycle
can be achieved by respecting the specified number of place
settings.
To reduce consumption even further, only run the dishwasher
when it is full.
Note for Test Laboratories:
forinformationoncomparativeEN
testing conditions, please send an email to the following address:
Half load
If there are not many dishes to be washed, a half
load cycle may be used in order to save water, electricity
and detergent. Select the wash cycle and press the HALF
LOAD button; the indicator light will go on.
Press the HALF LOAD button again to deselect this option.
Remember to halve the amount of detergent.
Special wash cycles
and Options
EN
12
Rinse aid and refined salt
Only use products which have been specifically designed
for dishwashers.
Do not use table/industrial salt or washing-up liquid.
Follow the instructions given on the packaging.
If using a multi-functional product it is not necessary to add
any rinse aid. However, we recommend that you add salt,
especially if you live in an area where the water is hard or
very hard.
(Follow the instructions given on the packaging).
If you do not add salt or rinse aid, the LOW SALT* and
LOW RINSE AID indicator lights will stay lit.
Measuring out the rinse aid
Rinseaidmakesiteasierforthecrockerytodry,aswaterrunsoff
the surfaces more readily and therefore does not leave streaks
or marks. The rinse aid dispenser should be filled:
• WhentheLOWRINSEAIDindicatorlight* on the control panel
is illuminated, a reserve supply of rinse aid is still available
for1-2cycles;
1.Openthedispenser“D” by pressing and pulling up the tab
on the lid;
2. Carefully introduce the rinse aid as far as the maximum
reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
Adjusting the amount of rinse aid
If you are not completely satisfied with the drying results, you
canadjustthequantityofrinseaid.Switchonthedishwasher
usingtheON/OFFbutton,waitafewsecondsandswitchitoff
usingtheON/OFFbutton.PresstheStart/Pausebutton3times;
switchonthemachineusingtheON/OFFbuttonand access
the adjustment menu - the rinse-aid indicator light is lit
(set to
factory level).
Adjust the level of rinse aid supply using the WASH CYCLE
SELECTknob.Thereisarinseaidlevelforeachwashcycle
(0to4max).
Press the ON/OFF button to save the setting.
IftherinseaidlevelissettoZERO(ECO),norinseaidwillbe
supplied.TheLOWRINSEAIDindicatorlightwillnotbelitifyou
run out of rinse aid.
• Iftherearestreaksonthecrockery,setalownumber(1-2).
• If there are drops of water or limescalemarks, set a high
number (3-4).
Setting the water hardness
Everydishwasherisequippedwithawatersoftenerwhich,by
using refined salt designed specially for this type of appliance,
supplies water without limescale which is then used to wash
the crockery.
This dishwasher has a setting that helps reduce pollution and
optimises washing performance in accordance with the water
hardness level in your area. Ask your local water supplier for
this information.
-Switch on thedishwasher using the ON/OFF button, wait a
fewsecondsandswitchitoffusingtheON/OFFbutton.Hold
downtheStart/Pausebuttonformin.3seconds;switchonthe
machineusingtheON/OFFbuttonandaccesstheadjustment
menu - the salt indicator light is lit.
-SelectthedesiredlevelusingtheSELECTWASHCYCLEknob
(1to5* Max.)
(water softener set to medium level).
Press the ON/OFF button to save the setting.
Evenifusingmulti-functionaltablets,fillthesaltdispenser.
(°dH=hardnessmeasuredinGermandegrees-°f=hardness
measuredinFrenchdegrees–mmol/l=millimolesperlitre)
Measuring out the refined salt
In order to obtain the best possible results from a wash cycle,
make sure that the salt dispenser is never empty.
Refinedsaltremoveslimescalefromthewater,thusavoiding
the formation of deposits on crockery.
The salt dispenser is located in the lower part of the dishwasher
(see Description)
and should be filled:
• Whenthegreenfloat* cannot be seen by simply looking at
the cap of the salt dispenser;
• WhentheLOWRINSEAIDindicatorlightonthecontrolpanel
is illuminated *;
1.Removethelowerrackandunscrew
the cap (anticlockwise).
2.Thefirsttimeyoudothis:fillthewater
tank right up to its edge.
3. Position the funnel
*
(see figure)
and
fill the salt dispenser up to the edge
(approximately 1 kg). It is normal for a
little water to leak out.
4.Removethefunnel*andwipeanysaltresiduesawayfrom
the opening; rinse the cap under running water and then screw
it on, the head facing downwards so as to let the water flow out
of the four slots (star-shaped arrangement) in the lower part of
the cap (cap with green float
*).
It is advisable to perform this procedure every time you add
salt to the dispenser.
Make sure the cap is screwed on tightly so that no detergent can
get into the container during the wash cycle (this could damage
the water softener beyond repair).
Whennecessary,measureoutthesaltbeforeawashcycle
so that any saline solution which has leaked out of the salt
dispenser is removed.
* Only available in selected models.
M
A
X
Water Hardness Table
Average salt dispenser
capacity duration
**
level °dH °fH mmol/l months
1 0 - 6 0 - 10 0 - 1 7 months
2 6 - 11 11 - 20 1,1 - 2 5 months
3 12 - 17 21 - 30 2,1 - 3 3 months
4 17 - 34 31 - 60 3,1 - 6 2 months
5
*
34 - 50 61 - 90 6,1 - 9 2/3 weeks
For values between 0°f and 10°f, we do not recommend the use of salt.
* a setting of 5 may increase cycle duration.
** 1 wash cycle per day.
EN
13
Care and maintenance
* Only available in selected models.
Shutting off the water and electricity
supplies
• Turn
off
the
water
tap
after
every
wash
cycle
to
avoid
leaks.
• Always
unplug
the
appliance
when
cleaning
it
and
when
performing maintenance work.
Cleaning the dishwasher
• The
external
surfaces
of
the
machine
and
the
control
panel
can be cleaned using a non-abrasive cloth which has been
dampened with water. Do not use solvents or abrasive
products.
• Any
marks
on
the
insideof
the
appliance
may
be
removed
using a cloth dampened with water and a little vinegar.
Preventing unpleasant odours
• Always
keep
the
door
of
the
appliance
ajar
in
order
to
avoid
moisture from forming and being trapped inside the machine.
• Clean
the
seals
around
the
door
and
detergent
dispensers
regularly using a damp sponge. This will avoid food becoming
trapped in the seals, which is the main cause behind the
formation of unpleasant odours.
Cleaning the sprayer arms
Food residue may become encrusted onto the sprayer arms
and block the holes used to spray the water. It is therefore
recommended that you check the arms from time to time and
clean them with a small non-metallic brush.
The two sprayer arms may both be removed.
To remove the upper sprayer arm,
turn the plastic locking ring in an
anti-clockwise direction. The upper
sprayer arm should be replaced
so that the side with the greater
number of holes is facing upwards.
The lower sprayer arm can be
removed by pressing on the side
tabs and pulling it upwards.
Cleaning the water inlet filter*
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free
of impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked
and damage the dishwasher.
Clean the water inlet filter at the tap outlet regularly.
- Turn off the water tap.
- Unscrew the end of the water inlet hose, remove the filter and
clean it carefully under running water.
-
Re-place
the
filter
and
screw
the
water
hose
back
into
position.
Cleaning the filters
The filter assembly consists of three filters which remove food
residues from the washing water and then recirculate the water.
They should be cleaned if you wish to achieve the best results
in every wash.
Clean the filters regularly.
The dishwasher should not be used without filters or if the
filter is loose.
•Afterseveralwashes,checkthefilterassemblyandifnecessary
clean it thoroughly under running water, using a non-metallic
brush and following the instructions below:
1. Turn the cylindrical filter C in an anti-clockwise direction and
pull it out
(fig.1).
2.RemovethecupfilterB by exerting a slight pressure on the
side flaps
(fig.2);
3. Slide out the stainless-steel plate filter A.
(fig. 3).
4. Inspect the trap and remove any food residues. NEVER
REMOVE the wash-cycle pump protection
(black detail) (fig.4).
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
Leaving the machine unused for extended
periods
• Disconnecttheappliancefromtheelectricitysupplyandshut
off the water tap.
• Leavethedooroftheapplianceajar.
• Whenyoureturn,runawashcyclewhenthedishwasheris
empty.
EN
14
Troubleshooting
Whenevertheappliancefailstowork,checkforasolutionfromthefollowinglistbeforecallingforAssistance.
* Only available in selected models.
Problem: Possible causes / solutions:
The dishwasher cannot be started or
controlled.
Switch off the appliance by pressing the ON/OFF button. Switch it back on
after approximately one minute and reset the program.
The appliance has not been plugged in properly.
The dishwasher door has not been shut properly.
The door won’t close.
The lock was released. Strongly push the door until a “clacking” noise is
heard.
No water drains from the
dishwasher.
The dishwasher cycle has not finished yet.
The water drain hose is bent (see Installation).
The drain duct is blocked.
The filter is clogged up with food residues.
The dishwasher is too noisy. The dishes are rattling against each other or against the sprayer arms.
An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-
up and use).
The dishes and glasses are
covered in a white film or
limescale deposits.
The level of refined salt is low or the dosage setting is not suited to the
hardness of the water (see Rinse aid and salt).
The lid on the salt dispenser was not closed properly.
The rinse aid has been used up or the dosage is too low.
The dishes and glasses are
streaked or have a bluish
tinge.
The rinse aid dosage is too high.
The crockery has not been
dried properly.
A wash cycle without a drying cycle has been selected.
The rinse aid has been used up or the dosage is too low (see Rinse aid and
salt).
The rinse aid setting is not suitable.
The crockery is made from non-stick material or plastic.
The crockery is not clean. The racks are overloaded (see Loading the racks.)
The crockery has not been arranged properly.
The sprayer arms cannot move freely.
The wash cycle is too gentle (see Wash cycles).
An excessive amount of foam has been produced: the detergent has not been
measured out correctly or it is not suitable for use in dishwashers (see Start-
up and use).
The lid on the rinse aid compartment was not shut correctly.
The filter is dirty or blocked (see Care and maintenance).
The refined salt level is low (see Rinse aid and salt).
The dishwasher does not take
any water in - Tap shut-off
alarm.
(The Drying and End indicator lights
ash quickly.)
There is no water in the mains supply.
The water inlet hose is bent (see Installation).
Turn on the tap and the appliance will start after a few minutes.
The appliance stopped because no action was taken when the beep
sounded*.
(*Only available on selected models.)
Switch off the machine using the ON/OFF button, turn on the tap and switch
the machine back on after 20 seconds by pressing the same button. Reset the
appliance and restart the wash cycle.
Kullanım talimatları
TR
BULAŞIK MAKİNESİ
Türkçe, 15
DFG 26B10
İçindekiler
Ürün bilgilerine, 16
Önlemler ve tavsiyeler, 17
Genel güvenlik
İmha Etme
Enerji tasarrufu ve Çevreye saygı
Kurulum, destek ve Yardım, 18-19
Konumlandırma ve düzleştirme
Su ve elektrik bağlantılarının yapılması
İlk yıkama programı hakkında öneri
Teknik bilgiler
Yardım
Cihazın tanımı, 20
Genel Bakış
Kontrol Paneli
Raarın yüklenmesi, 21-22
Alt raf
Çatal-bıçak sepeti
Üst raf
Üst rafın yüksekliğinin ayarlanması
Uygun olmayan sofra takımları
Çalıştırma ve kullanım, 23
Bulaşık makinesinin çalıştırılması
Deterjanın ölçülmesi
Yıkama programları, 24
Yıkama programları tablosu
Özel yıkama programları ve Seçenekler, 25
Parlatıcı ve rane tuz, 26
Durulama maddesinin ölçülmesi
İşlenmiş tuzun ölçülmesi
Temizlik ve bakım, 27
Su ve elektrik bağlantısının kapatılması
Bulaşık makinesinin temizlenmesi
İstenmeyen kokuların önlenmesi
Püskürtücü kollarının temizlenmesi
Su Giriş Filtresinin Temizlenmesi
Filtrelerin temizlenmesi
Makinenin uzun süre kullanılmaması
Sorun giderme, 28
TR
16
ürün bilgilerine
Marka
INDESIT
Model
DFG 26B10
Standart yer yerleşimlerinde nominal kapasite (1)
13
A+++ (düşük tüketim)’’dan D (yüksek tüketim)’’e Enerji verimlilik sınıfı
A+
kWh cinsinden yıllık enerji tüketimi (2)
295.0
kWh cinsinden standart temizleme programının enerji tüketimi
1.04
W’’de off-modun güç tüketimi
0.5
W’’de left-on modun güç tüketimi
5.0
Litre olarak yıllık su tüketimi (3)
3080.0
A (yüksek verim)’’dan G (düşük verim)’’e kurutma verimlilik sınıfı
A
Dakika cinsinden standart temizleme programı için program süresi
190
Left-on modun dakika cinsinden süresi
10
Yıkamada dB(A) re 1 pW cinsinden gürültü
51
Ankastre Model
Hayır
Notlar
1) Etiket ve ş üzerinde yer alan bilgi, standart yıkama programı ile ilişkilidir, bu programın normal olarak kirlenmiş sofra takımlarını
yıkamak için uygundur ve kombine enerji ve su tüketimi açısından en etkili programlardır. Standart yıkama programı, Eco program’’dır.
2) Soğuk su kullanılan 280 adet standart yıkama programına ve ve düşük güç modlarının tüketimine dayanmaktadır. Gerçek enerji
tüketimi cihazın nasıl kullanıldığına göre değişecektir.
3) 280 adet standart yıkama programına dayanmaktadır. Gerçel su tüketimi, cihazın nasıl kullanıldığına bağlıdır.
Ürün bilgilerine
TR
17
* Yalnızca belirli modellerde bulunmaktadır.
Önlemler ve öneriler
Bu cihaz, uluslararası güvenlik standartlarına
uygun olarak tasarlanıp üretilmiştir. Aşağıdaki bilgiler
güvenlik amacıyla verilmiştir ve bu nedenle dikkatle
okunmalıdır.
Bu kullanım kılavuzunu, gelecekte referans olarak
kullanmak üzere saklayın. Cihazı satarsanız, birine
hediye ederseniz veya başka bir yere taşırsanız, kullanım
kılavuzunu da vermeyi/götürmeyi ihmal etmeyin.
Lütfen bu talimatları dikkatle okuyun: talimatlar,
kurulum, kullanım ve güvenlik hakkında önemli
bilgiler içermektedir.
Bu cihaz, evde kullanmanın yanı sıra benzeri
uygulamalarda da kullanılmak üzere tasarlanmıştır;
örneğin:
- mağazalar, osler ve diğer çalışma ortamlarındaki
personel mutfağı alanları;
- çiftlik evleri;
- oteller, moteller ve diğer yerleşim türü ortamlarında
müşteriler tarafından;
- oda-kahvaltı sistemiyle hizmet veren turistik tesisler.
Genel güvenlik
Bu cihaz, güvenliklerinden sorumlu bir kişi tarafından
cihazın kullanımıyla ilgili talimatlar kendilerine
öğretilmeden veya bu kişinin gözetimi altında olmadan
ziksel, ruhsal veya akli durumları yeterli olmayan
kişiler (çocuklar dahil) ya da gerekli bilgi ve tecrübeye
sahip olmayan kişiler tarafından kullanılmamalıdır.
Yetişkinler, cihazla oynamadıklarından emin olmak
için çocukları her zaman gözetim altında tutmalıdır.
Cihaz ev içi kullanım için tasarlanmıştır ve ticari
veya endüstriyel kullanım amaçlanmamıştır.
Ev bulaşıklarının bu kullanım kılavuzunda belirtilen
şekilde yıkanması için makine sadece yetişkinler
tarafından kullanılmalıdır.
Aygıt, üzeri kapatılarak olsa bile açık alanlara
kurulmamalıdır. Makinenin yağmur ve fırtınaya
maruz bırakılması son derece tehlikelidir.
Ayaklarınız çıplakken cihaza dokunmayın.
Cihazı fişten çekerken, daima fişi duvardaki
elektrik prizinden çekin, kablodan çekmeyin.
Kablosunu çekmeyin.
Cihaz temizlenmeden veya bakım yapılmadan
önce su besleme musluğu kapatılmalı ve cihazın
şi mutlaka prizden çıkarılmalıdır.
Makine arızalanırsa, hiçbir koşulda makineyi
kendiniz tamir etmeye çalışmayın ve makinenin
iç kısımlarına dokunmayın.
Cihaza yaslanmayın, üzerine oturmayın: cihaz
devrilebilir.
Kapak, tehlikeli bir engel yaratabileceği için açık
bırakılmamalıdır.
Deterjan ve parlatıcıyı çocukların erişemeyeceği
bir yerde muhafaza edin.
Ambalaj malzemeleri çocuklar tarafından oyuncak
gibi kullanılmamalıdır:
Elden Çıkarma
Ambalaj malzemesinin elden çıkarılması:
paketlerin/ambalaj malzemelerinin yeniden
kullanılabilir olup olmadığına dair yerel yasaları
inceleyin.
Atık Elektrikli ve Elektronik Ekipmanların (AEEE)
elden çıkarılması hakkında Avrupa birliği Direkti
2012/19/EU, elektrikli ev aletlerinin normal
evsel atıklar gibi elden çıkarılmaması gerektiğini
belirtmektedir. Hizmet ömrünü tamamlayan
cihazlar, makinenin içindeki malzemelerin yeniden
kullanılma ve geri dönüştürülme maliyetlerinin
optimize edilmesini sağlamak ve doğaya ya da halk
sağlığına zararlı etkileri önlemek amacıyla ayrı bir
şekilde toplanmalıdır. Üzeri çarpı işaretli çöp kovası
simgesi, bu atıkların ayrı bir şekilde toplanması
gerektiği konusunda o ürünün kullanıcılarını
uyarmak amacıyla tüm ürünlere konmaktadır.
Konutlarda kullanılan elektrikli cihazların doğru bir
şekilde elden çıkarılması konusunda ayrıntılı bilgi
edinmek için ilgili kamu kuruluşuna ya da yerel
bayinize başvurabilirsiniz.
Enerji tasarrufu ve Çevreye saygı
Su ve enerji tasarrufu
Sadece bulaşık makinesi dolu olduğu zaman
yıkama devrini başlatın. Bulaşık makinesinin
dolmasını beklerken, sudan geçirme devrini
kullanarak istenmeyen kokuların oluşmasını
önleyin (
Yıkama Devirleri’ne
bakın).
Yıkama devirleri tablosunu kullanarak bulaşıkların
kirlilik seviyesine ve bulaşık tipine uygun olan
yıkama devrini seçin:
- normal bulaşık seviyesindeki tabaklar için, düşük
enerji ve su tüketimi seviyelerini temin eden
Ekonomik yıkama devrini kullanın.
- Bulaşıklar normalden daha azsa, Yarım Bulaşık
seçeneğini etkinleştirin*
(bkz. Çalıştırma ve Kullanım).
Elektrik tedarikçiniz indirimli elektrik tarifeleri
hakkında bilgi vermişse, yıkama devirlerini
elektrik fiyatlarının düşük olduğu zamanlarda
gerçekleştirin. Gecikmeli Çalıştırma düğmesi *
(bkz. Çalıştırma ve Kullanım)
yıkama devirlerinizi
buna göre düzenlemenize yardımcı olur.
Enzim içeren fosfatsız ve klorsuz deterjanlar
Bu ürünler çevreye zararlı olduğu için fosfat veya
klor içeren deterjanları kullanmamanızı kesinlikle
tavsiye ederiz.
Enzimler 50°C civarındaki sıcaklıklarda özel bir
etki sağlar ve bunun sonucunda enzim içeren
deterjanlar normal 65°C'lik yıkama devriyle aynı
sonucu elde etmek için düşük sıcaklıktaki yıkama
devirlerinde kullanılabilirler.
Deterjanın boşa kullanılmasını önlemek için,
ürünü üretici önerilerine dayanan miktar, su
sertliği, bulaşık seviyesi ve çanak çömlek
miktarında kullanın. Toprakta çözünebilir olsalar
bile, deterjanlar doğanın dengesinde değişiklik
yapabilecek maddeler içerir.
TR
18
* Yalnızca belirli modellerde bulunmaktadır.
Taşıma halinde cihazı dik tutunuz ya da gerekli olduğu
takdirde arka tarafa doğru yatırınız.
Yerleştirme ve seviye ayarlama
1. Cihazın ambalajını çıkartınız ve cihazda nakliyat sırasında
hasar meydana gelip gelmediğini kontrol ediniz. Hasarlı ise, cihazı
bağlamadan hemen Teknik Servise başvurunuz.
2. Bulaşık makinesini, makinenin arka tarafı yada yanları duvara
yada yanındaki mobilyalara dayanacak şekilde yerleştiriniz.
Cihaz, mutfak tezgahının altına ankastre edilebilir
*
(Montaj
bölümüne bakınız)
.
3. Bulaşık makinesini düz ve sert bir zemine yerleştiriniz. Cihaz
yatay oluncaya kadar, ön ayakları sökerek veya vidalayarak
eğrilikleri dengeleyiniz. Cihazın seviyesinin dikkatlice ayarlanması
makinenin titremesini, ses çıkarmasını ve yerinden oynamasını
engeller.
4
*. Arka ayağın yüksekliğini ayarlamak için, bulaşık makinesinin
alt, ön, orta kısmında mevcut olan kırmızı renkteki altıgen kılavuz
üzerinde işlem yapınız. 8 mm'lik açıklığa sahip altıgen ağızlı
bir anahtar ile, yüksekliği arttırmak için saat yönünde çeviriniz
ve yüksekliği azaltmak için ise saat yönünün tersinde çeviriniz.
(belgelere ek ankastre talimatları bölümüne bakınız)
Elektrik ve su bağlantıları
Bu cihazın montajı sırasındaki elektrik ve su tesisatlarının
sadece vasıı personel tarafından yapılması gerekir.
Bulaşık makinesi, elektrik kabloları veya boruları üzerine
yaslanmamalıdır.
Cihaz, su dağıtma şebekesine yeni borular kullanılarak
bağlanmalıdır.
Eski boruları yeniden kullanmayınız.
Montajı kolaylaştırmak için, su doldurma ve boşaltma hortumları
ve elektrik besleme kablosu sağa veya sola döndürülebilir.
Su besleme hortumunun bağlantısı
Soğuk su girişine: doldurma hortumunu 3/4 inç yivli musluğa
iyice vidalayınız, hortumu musluğa vidalamadan önce suyun
içindeki atıkların cihazı tıkamaması için suyu temiz oluncaya
kadar akıtınız.
Sıcak su girişine: merkezi ısıtma sistemi söz konusu ise;
bulaşık makinesi sıcak suya bağlı olarak çalışabilir, ancak
suyun sıcaklığı 60°C’yi geçmemelidir.
Hortumu, soğuk su girişine bağlanması bölümünde
açıklandığı gibi musluğa vidalayınız.
Su doldurma hortumunun uzunluğu montaj için yeterli değil
ise, konusunda uzman bir mağazaya ya da yetkili bir teknisyene
başvurunuz
(bakınız Teknik Destek)
.
Suyun basıncı, Teknik veriler tablosunda aktarılan değerler
dahilinde olmalıdır
(yan tarafa bakınız)
.
Hortumun kıvrılmamasına, bükülmemesine veya sıkışmamasına
dikkat ediniz.
Atık su boşaltma hortumunun bağlantısı
Atık su boşaltma hortumunu, kıvırmadan iç çapı en az 4 cm olan
bir boşaltma kanalına bağlayınız
Boşaltma hortumu, zeminden veya bulaşık makinesinin destek
zemininden (A) 40 ila 80 cm. arasında bir yükseklikte olmalıdır.
Atık su boşaltma hortumunu lavabonun akış borusuna
bağlamadan önce, plastik tapayı (B) kaldırınız.
Su basmalarına karşı emniyet sistemi
Bulaşık makinesi, su basmasını önlemek için:
- herhangi bir arıza ya da içeriden su kaybı olması durumunda
su girişini durdurma sistemine sahiptir.
Bazı modeller, besleme hortumunun kopması halinde de su
basmalarını önleyen, New Acqua Stop
*adı verilen ilave bir
emniyet sistemine sahiptir.
DİKKAT: TEHLİKELİ GERİLİM!
Su doldurma hortumu, her ne olursa olsun asla kesilmemelidir:
çünkü içerdiği bazı parçalar gerilim altındadır.
Elektrik bağlantısı
Cihazın şini bir elektrik prizine takmadan önce, aşağıdakileri
kontrol ediniz:
prizin topraklı tesisata sahip ve yasal kurallara uygun
olduğunu;
elektrik prizinin kapağın karşısındaki özellikler plakasında
belirtilen, makinenin maksimum güç yükünü taşıyabildiğini
(Cihazın tanımı bölümüne bakınız);
besleme geriliminin kapağın karşısındaki özellik plakasında
belirtilen değerler dahilinde olduğunu;
prizin cihazın şi ile uyumlu olduğunu. Aksi takdirde cihazın
şinin değiştirilmesi için yetkili bir teknisyene
(Teknik Destek
bölümüne bakınız) başvurunuz
; uzatma kablosu ya da çoklu
priz kullanmayınız.
Cihaz monte edildikten sonra, besleme kablosuna ve elektrik
prizine kolayca ulaşılabilmelidir.
Kablonun ezilmemesi ve katlanmaması gerekir.
Besleme kablosu zarar görmüş ise, herhangi bir riski önlemek
için derhal Teknik Destek Servisi veya üretici rma tarafından
yenisi ile değiştirilmelidir.
(Bakınız Teknik Destek)
Kurulum - Yardım
TR
19
Makine, kumandanın gerçekleştiğini bildiren sesli/tonlu
sinyaller
(bulaşık makinesinin modeline göre
) ile donatılmıştır:
açma, devre sonu, vb.
Kumanda paneli/ekran üzerinde mevcut olan ışıklı semboller/
uyarı lambaları/ledler, renk, basış ya da sabit ışıklı olma
değişikliği gösterebilir.
(bulaşık makinesinin modeline göre)
.
* Yalnızca belirli modellerde bulunmaktadır.
Desteğe başvurmadan önce
Problemin Sorun Giderme rehberi kullanılarak çözülüp
çözülmeyeceğini kontrol edin
(bkz. Sorun Giderme)
.
Karşılaştığınız problemin devam edip etmediğini görmek
için programı baştan başlatın.
Sorun devam ediyorsa, Yetkili Teknik Servis ile temas
kurun.
Yetkisiz teknisyenlerin verdiği hizmetleri kullanmayın.
Lütfen aşağıda belirtilen bilgileri hazır edin:
Arıza tipi.
Cihaz Modeli (Mod).
Seri Numarası (S/N).
Bu bilgiler, cihazın bilgi plakası üzerinde bulunur
(bkz. Cihazın
tanımı)
.
INDESIT COMPANY BEYAZ EŞYA PAZARLAMA A.Ş.
Karahasan Sok. No:11 Balmumcu 34349 Beşiktaş/İstanbul
TEL: (+90) 212 355 53 00
FAKS: (+90) 212 212 95 59
WEB: www.hotpoint-ariston.com.tr
“Cihazýn ömrü 10 yýldýr”
Servis
Yoğunlaşma önleyici şerit*
Bulaşık makinesini kurduktan sonra kapağı açın ve bulaşık
makinenizi yoğuşma nedeniyle oluşan muhtemel sorunlardan
korumak için yapışkanlı bandı ahşap rafın altına yapıştırın.
İlk yıkama programı hakkında öneri
Kurulumdan sonra stoperleri raardan çıkarın ve varsa üst
raftaki elastik sabitleme elemanlarını da sökün.
Cihazın kurulumu tamamlandıktan sonra ve ilk yıkama
programını başlatmadan hemen önce tuz dağıtıcısını
tamamıyla su ile doldurun ve ancak bundan sonra yaklaşık
1 kg kadar tuz ekleyin
(Durulama maddesi ve işlenmiş
tuz başlıklı bölümü inceleyin)
. Su taşabilir: bu normal
bir durumdur, endişe etmeyin. Su sertliği değerini seçin
(Durulama maddesi ve işlenmiş tuz bağlıklı bölümü inceleyin)
.
- Tuz, makinenin içine döküldükten sonra, YETERSİZ TUZ
(LOW SALT) göstergesi*
sönecektir.
Tuz kabı dolu değilse, su yumuşatıcı ve ısıtma elemanı
bunun sonucunda hasar görebilir.
Yardım
Teknik bilgiler
Boyutlar
Genişlik 60 cm.
Yükseklik 85 cm.
Derinlik 60 cm.
Kapasite 13 standart yer ayarı
Su şebeke basıncı
0.05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 - 145 psi
Güç kaynağı voltajı Bilgi levhasına bakınız
Toplam absorbe
edilen güç
Bilgi levhasına bakınız
Sigorta Bilgi levhasına bakınız
Bu bulaşık makinesi aşağıdaki
Avrupa Birliği Yönergelerine uy
gundur:
- 2006/95/EC (Düşük Voltaj)
-2004/108/EC (Elektromanyetik
Uygunluk)
-2009/125/EC (Comm. Reg.
1016/2010) (Ecodesign)
-97/17/EC(etiket ket Yönergesi)
-2012/19/EU “AEEE Yönetmeliğ
ine uygundur”
TR
20
Genel Bakış
Cihazın açıklaması
*** Yalnızca tamamen gömme olan modellerde.
* Yalnızca belirli modellerde bulunmaktadır.
Kontrol Paneli
Yıkama programı ve seçeneklerinin sayısı ve türü bulaşık makinesi modeline bağlı olarak farklılık gösterebilir.
1. Üst raf
2. Üst püskürtücü kolu
3. Açılır/kapanır dağıtıcılar
4. Raf yüksekliği ayarlayıcı
5. Alt raf
6. Alt püskürtücü kolu
7. Yıkama ltresi
8. Tuz dağıtım bölmesi
9. Deterjan dağıtıcı, durulama katkı maddesi
dağıtıcı ve Active Oxygen cihazı*
10.
Bilgi levhası
11. Kontrol paneli***
Başlat/Duraklat düğmesi
ve gösterge ışığı
AÇMA/KAPATMA/Sıfırlama
düğmesi ve gösterge ışığı
Devir seçim düğmesi
Gösterge ışığı
Düşük Tuz
Düğme ve gösterge ışığı
Yarım Yükleme seçeneği
Gösterge ışığı Yıkama ve
Gecikmeli Başlatma (3 saat)
Gösterge ışığı Kurutma ve
Gecikmeli Başlatma (6 saat)
Gösterge ışığı Yıkama Çevrimi Sonu
ve Gecikmeli Başlatma (9 saat)
Düğme ve gösterge ışığı
Gecikmeli başlatma
Parlatıcı
gösterge ışığı
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Indesit DFG 26B10 NX EU Kullanici rehberi

Kategori
Bulaşık makineleri
Tip
Kullanici rehberi

Diğer dillerde