Yamaha TSX-132 Black Kullanım kılavuzu

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

16

May

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

TSX-132

G

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place -

away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a

lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the

wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the system to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the system off, then leave this unit alone for

cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

– Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or

her mouth.

– If the batteries grow old, the effective operation range of

the remote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

– Do not use old batteries together with new ones.

– Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have the

same shape and color.

– Exhausted batteries may leak. If the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

– If you plan not to use the unit for a long period of time,

remove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery

liquid that may damage the unit.

– Do not throw away batteries with general house waste.

Dispose of them correctly in accordance with your local

regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

based (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English

NAMES OF PARTS AND THEIR FUNCTIONS ........2

Top panel / Front panel..................................................2

Front panel display.........................................................3

Rear panel......................................................................3

Remote control...............................................................4

TURNING THE SYSTEM ON ....................................5

ADJUSTING THE CLOCK ........................................5

LISTENING TO YOUR iPod......................................6

Playing music from your iPod.........................................6

Using repeat/shuffle playback (remote control only)......6

LISTENING TO CD AND USB DEVICES .................7

Listening to a CD............................................................7

Listening to a USB device..............................................8

Using repeat/shuffle playback (remote control only)......8

LISTENING TO FM STATIONS ................................9

Selecting an FM station..................................................9

Presetting FM stations (remote control only) ...............10

Selecting preset FM stations........................................11

LISTENING TO EXTERNAL SOURCES ................11

USING THE ALARM FUNCTION............................12

Using “DTA Controller” to set the alarm .......................12

Setting the alarm ..........................................................13

Operations while the alarm sound is playing................14

USING THE SLEEP TIMER ....................................15

ADJUSTING THE TONE (remote control only)....15

ADJUSTING THE BRIGHTNESS OF THE FRONT

PANEL DISPLAY (remote control only) ...............15

TROUBLESHOOTING ............................................16

NOTES ON DISCS AND USB DEVICES................18

SPECIFICATIONS...................................................

19

CONTENTS

• Play back music from external devices such as your iPod/iPhone/iPad, audio/data CDs, USB devices, or external devices

via the AUX, and listen to the FM.

• Use your favorite music or a beep tone as an alarm. When the set time arrives, the music you select is played at the volume

that you specify, giving you the ideal start to your day (IntelliAlarm function).

• You can take advantage of more sophisticated alarm functionality by using the free “DTA Controller” application for the

iPod touch/iPhone/iPad (☞ P. 12).

• You can easily store and recall 30 of your favorite FM stations.

• Bass, middle, and treble can be adjusted to your taste.

 About this manual

• References to the iPod appearing in this manual also include the iPhone.

• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will

focus on operation using the main unit.

 How to use the remote control  Replacing the battery in the remote control

While pushing the release tab in direction , slide out the

battery holder in direction .

Features

Supplied accessories

Dock coverFM antenna

(uses a CR2032 type

Lithium Battery)

Remote control USB cap

Keep the USB cap out

of reach of children so

as to ensure that it is not

mistakenly swallowed.

Within 6 m (20')

Battery insulation sheet:

Remove before using.

CR2032 type

Lithium Battery

2 En

a VOLUME – / +

Adjust the volume.

b (Power)

Press to turn the system on/off (☞ P. 5).

c Source buttons

Switch the audio source to be played.

If you press one of these while the system is off, the

system will turn on and then switch the audio source.

d iPod dock

Connect your iPod here (refer to “Placing your iPod in

the iPod dock” below).

e Audio control buttons

Use these to operate the iPod/CD/USB device.

f SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(☞ P. 14, 15).

g USB port

Connect your USB device / iPod / iPhone / iPad here

(☞ P. 8).

When the USB device is not in use, put the USB cover in place

to protect the connector.

h PRESET /

Use these buttons to select a FM station (preset) that

you’ve stored (☞ P. 11).

i TUNING /

Tune the FM (☞ P. 9).

j Front panel display

The clock and other information is displayed here

(☞ P. 3).

k ENTER

Confirm a selected item or value.

l Disc slot

Insert a CD here (☞ P. 7).

m EJECT

Eject the CD.

n – / +

Select an item or value when setting the clock or the alarm.

o SET

Set the alarm (☞ P. 13).

p ALARM

Switch the alarm on/off (☞ P. 14).

q (Headphone jack)

Connect headphones here.

NAMES OF PARTS AND THEIR FUNCTIONS

Top panel / Front panel

q

3

4 7 8 95612

op kn lm j

:

Stop

:

Play/Pause

/:

Skip, Search backward/forward (press and

hold down)

 Placing your iPod in the iPod dock

Your iPod will be recharged while it is connected to the dock. However if USB is selected as the

source, the iPod will not be recharged.

• Be sure to use a dock adaptor that is compatible with your iPod. If you do not use the adaptor or the adaptor is

not compatible, the connection could be loose or poor, which could cause damage to the connector. For details

on dock adaptor information, please visit Apple’s official website.

• If an iPod in a protective case is forcibly connected, the connector may be damaged. Remove the protective

case before connection.

• When the iPod is not in use, put the iPod dock cover in place to protect the connector.

Dock

adaptor

3 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

a Illumination sensor

Detect ambient lighting. Do not cover this sensor.

b Alarm time

This indicates the alarm time.

c Repeat/shuffle indicator

Display the playback mode (☞ P. 6, 8).

d Multi-function indicator

Display various information, including the clock time,

information about the currently-playing track, and the

frequency of the FM station.

e Remote control signal receiver

Make sure that this sensor is not obstructed (☞ P. 1).

f Sleep indicator

Turn on if the sleep timer has been set (☞ P. 15).

g Alarm indicator

Turn on if the alarm has been set (☞ P. 14).

h Weekly alarm indicator

Shows alarm information specified using the free “DTA

Controller” application for the iPod touch/iPhone/iPad

(☞ P. 12)

a CLOCK switch

Sets the clock and specifies whether the clock will be

displayed (☞ P. 5).

b AUX

Use a commercially available 3.5 mm mini-plug cable

to connect your external device here (☞ P. 11).

c FM antenna connector

Connect the FM antenna here.

• If reception is poor, try changing the height or direction of the

antenna, or move the unit to find a location that has better

reception.

• If you use a commercially available outdoor antenna instead of

the supplied antenna, reception may be better.

Front panel display

~~~~~~

54

8

21

7 6

3

Rear panel

FM ANT

ON

CLOCK AUX

SET OFF

1 2 3

SET:

Set the clock.

ON:

Even when the system is off, the clock will be

displayed and the alarm function will be available.

OFF:

When the system is off, the clock will not be

displayed and the alarm function will not be

available.

FM ANT

Be sure to stretch out the antenna.

NAMES OF PARTS AND THEIR FUNCTIONS

4 En

a Remote control signal transmitter

b (Power)

Press to turn the system on/off (☞ P. 5).

c SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(☞ P. 14, 15).

d ALARM

Switch the alarm on/off (☞ P. 14).

e Source buttons

Switch the audio source to be played.

If you press one of these while the system is off, the

system will turn on and then switch the audio source.

f MENU

Switch the iPod menu item / Return to the previous

menu (☞ P. 6).

g FOLDER S / T

Switch the playback folder when playing music on data

CDs or USB devices (☞ P. 7, 8).

Select items or edit numerical values (☞ P. 6, 15).

h ENTER

Confirm a selected item or value.

i Audio control buttons

Use these to operate the iPod/CD/USB device.

j (Repeat)/ (Shuffle)

Play music on an iPod, CD or USB device in repeat/

shuffle mode (☞ P. 6, 8).

k EQ: LOW/MID/HIGH

Adjust the bass, middle or treble sound quality

(☞ P. 15).

l TUNING /

Tune the FM (☞ P. 9).

m PRESET /

Select a FM station (preset) that you’ve stored

(☞ P. 11).

n MEMORY

Store a FM station (☞ P. 10).

o MUTE

Mute or unmute the sound.

p VOLUME + / –

Adjust the volume.

q DISPLAY

Switch the information shown in the front panel display

(☞ P. 6, 7, 8, 9).

r DIMMER

Adjusts the brightness of the front panel display

(☞ P. 15).

Remote control

3

4

5

7

6

9

j

k

l

m

n

1

8

2

q

o

p

r

iPod control buttons

:Stop

: Play/Pause

/ : Skip, Search backward/forward (press and

hold down)

5 En

English

TURNING THE SYSTEM ON

Connect the power cable to an AC outlet, and

press .

The system will turn on, and will be ready to play audio

sources.

To turn the system off, press once again.

If you set the rear panel CLOCK switch to the OFF position

(☞ P. 3), the clock will not be displayed when the system is off,

reducing the power consumption.

ADJUSTING THE CLOCK

1 Set the rear panel CLOCK switch to the SET

position.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

2 Set the date and time.

Press the front panel – / + buttons to edit the values,

and press ENTER to confirm the settings.

Set the items in the order of year month day

hour minute.

When clock setting has finished, the display will

indicate “Completed!”

• On step , you can copy the time of iPod instead of

setting time manually by setting the iPod to the iPod dock.

The time will not be copied if the iPod is already connected.

• On step , by pressing SNOOZE/SLEEP you can select

the time format (12-hour / 24-hour).

3 When you’ve finished making settings, set

the CLOCK switch to the ON position.

The moment you set the switch to the ON position, the

clock will start from 0 second.

The time settings will be reset if the unit remains unpowered for

more than one week.

26

Apr

15:30

iPod

Display (24-hour) when the system is on

Display (24-hour) when the system is off (CLOCK switch: ON)

Clock display

when the

system is off

Alarm

Recharging

your iPod in

the iPod dock

CLOCK switch: ON

Yes Enabled Yes

CLOCK switch: OFF

(power-saving)

No Disabled Yes

ON

CLOCK AUX

SET OFF

26

Apr

Front panel

1

2

ON

CLOCK AUX

SET OFF

3

Rear panel

Jan Feb Mar Apr May Jun

January February March April May June

Jul Aug Sep Oct Nov Dec

July August September October November December

(24-hour)

2

6 En

󰃰

• For details on compatible iPod models, refer to “SPECIFICATIONS” (P. 19).

• Your iPod can also play back music and recharge while connected to the USB port (☞ P. 8).

 iPod menu operations (remote control only)

 Display information (remote control only)

The playback status is shown by the repeat/shuffle indicator (☞ P. 3) in the front panel display.

Repeat playback Shuffle playback

Repeat/shuffle may not operate or be displayed correctly as shown above depending on the type of iPod used.

LISTENING TO YOUR iPod

Playing music from your iPod

1 Press the iPod source button to switch the

audio source to iPod.

2 Set your iPod in the iPod dock (☞ P. 2 ) .

3 Play the iPod.

Playback can be controlled with either the remote

control, iPod or the unit (☞ P. 2, 4).

• If you’ve selected an audio source other than USB, performing

the following operations will automatically switch the audio

source to iPod and start playback even if this system is turned

off.

− Connect your iPod in the playback state to the iPod dock.

− Play back the connected iPod.

• If USB is selected as the audio source, the iPod will not be

charged.

• You can remove the iPod during playback.

• If iPod is selected as the audio source, the system will

automatically turn off when 60 minutes have elapsed without a

device being connected to the iPod dock nor any operation

performed.

You can use the remote control to operate your iPod.

If you press DISPLAY on the remote

control while a song is playing or paused,

the information shown on the front panel

display will be switched in the order shown

at right.

Using repeat/shuffle playback (remote control only)

FM

AUX USB

CD iPod

RADIO

21

Dock adaptor

(☞ P. 2)

MENU: Switch menu items / Return to the previous menu

▲/▼: Move between items in the menu

ENTER: Confirm

Elapsed song playback time

Song name

Album name

Artist name

Press (repeat) on the remote

control repeatedly to select one of

the following playback modes.

No display: Off

: One

: All

Press (shuffle) on the remote

control repeatedly to select one of

the following playback modes.

No display: Off

: Albums

: Songs

7 En

English

 Skipping folders (remote control only)

 Display information (remote control only)

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played back is stopped, the track that was being played back will start playing from the

beginning of the track the next time playback begins.

• If you press while playback is stopped, tracks will play as follows the next time playback begins:

− Audio CD: Play from the first track of the CD.

− Data CD (a CD containing MP3/WMA files) or USB: Play from the first track in the folder containing the song that you last stopped.

• This unit automatically turns off the system if no operation has been performed for 60 minutes after CD/USB device

playback is stopped.

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (P. 18).

Listening to a CD

1 Press the CD source button to switch the

audio source to CD.

If a CD is already inserted, playback will start.

2 Insert a CD into the disc slot.

Playback starts automatically.

Playback can be controlled with either the remote

control or the unit (☞ P. 2, 4)

.

Insert the CD with the label side facing upward.

Folders and files on a data CD are played in alphabetical order.

While a data CD is playing, you can use the remote control’s FOLDER ▲/▼

buttons to select the folder.

The folder number (only for a data CD) or the song/file number is shown for

several seconds when starting playback or skipping tracks.

If you press DISPLAY on the remote control while a song is playing or paused,

the information shown on the front panel display will be switched in the following

order.

FM

AUX USB

CD iPod

RADIO

1

2

Audio CD

Elapsed song playback time

Remaining song playback time

Song name*

Album name*

Artist name*

Data CD

Elapsed song playback time

Song name*

Album name*

Artist name*

File name

Folder name

* Shown only if this data is included in the song.

LISTENING TO CD AND USB DEVICES

8 En

 Skipping folders (remote control only)

 Display information (remote control only)

The playback status is shown by the repeat/shuffle indicator (☞ P. 3) in the front panel display.

Repeat playback Shuffle playback

Listening to a USB device

1 Press the USB source button to switch the

audio source to USB.

If a USB device is already connected, playback will

start.

2 Connect a USB device to the USB port.

Playback starts automatically. Playback can be

controlled using either the remote control, the unit, or

the USB device (☞ P. 2, 4).

Folders and files will play in the order in which they were

written.

Stop playback before disconnecting the USB device.

While a USB device is playing, you can use the remote control’s FOLDER ▲/▼

buttons to select the folder.

The folder/file number is shown for several seconds

when starting playback or skipping tracks.

If you press DISPLAY on the remote control while a

song is playing or paused, the information shown on the

front panel display will be switched in the order shown

at right.

* Shown only if this data is included in the song.

Using repeat/shuffle playback (remote control only)

FM

AUX USB

CD iPod

RADIO

1 2

Your iPod/iPhone/iPad can also

play back music and recharge

while connected to the USB port

(☞ P. 6).

Elapsed song

playback time

Song name*

Album name*

Artist name*

File name

Folder name

Press (repeat) on the remote

control repeatedly to select one of

the following playback modes.

No display: Repeat mode off

: 1 track

: All tracks within the

folder (data CD/

USB device only)

: All tracks

Press (shuffle) on the remote

control repeatedly to select one of

the following playback modes.

No display: Shuffle mode off

: All tracks within

the folder (data CD/

USB device only)

: All tracks

9 En

English

Connect the antenna if you want to listen to the FM (☞ P. 3).

 Display information

If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the

following order.

Displaying Radio Data System information

If you press DISPLAY on the remote control while Radio Data System information is

being received, the information shown on the front panel display will be switched in the

order shown at right.

If the signal transmission of the Radio Data System station is too weak, this unit may not be able to

receive Radio Data System information completely. In particular, RT (Radio Text) information uses a

lot of bandwidth, so it may be less available compared to other types of information.

LISTENING TO FM STATIONS

Selecting an FM station

1 Press the FM source button to switch the

audio source to FM.

2 Tuning FM stations.

Automatic tuning: Press and hold

TUNING /

.

Manual tuning: Press TUNING / repeatedly.

If you tune to a station manually while receiving FM, the

sound will be monaural.

AUX USB

CD iPod

FM

RADIO

1

2

Preset number and frequency Reception status*

* Examples of reception status indication.

TUNED/STEREO: A strong FM stereo broadcast is being received.

TUNED/MONO: Receiving an FM broadcast in monaural (even if the FM broadcast is stereo, reception will be

monaural if the signal is weak).

Not TUNED: No broadcast is being received.

PS (Program Service)

PTY (Program Type)

RT (Radio Text)

CT (Clock Time)

Reception status

Preset number and

frequency

LISTENING TO FM STATIONS

10 En

Use the preset function to store your favorite 30 stations.

 Auto preset

This method tunes automatically, and automatically presets only the stations that have good reception.

 Manual preset

 Deleting a stored preset

Presetting FM stations (remote control only)

1 Press and hold down MEMORY on the

remote control.

“AUTO PRESET” will appear and “Press MEMORY”

will blink.

2 Press MEMORY.

Auto preset will begin.

When presetting has finished, the display will indicate

“Completed!”

When you perform auto preset, all stored stations are cleared

and the new stations are stored.

If you want to stop auto preset before it is completed, press .

1 Select the station that you want to preset,

and press MEMORY.

The display will indicate “PRESET MEMORY.”

2 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already been

stored, it will be overwritten by the new station.

3 Press MEMORY to complete the operation.

The preset will be stored, and the display will indicate

“Completed!”.

1 Press MEMORY on the remote control.

The display will indicate “PRESET MEMORY,” and

the preset number will blink.

2 Press TUNING

/

to select the preset

delete operation.

The display will indicate “PRESET DELETE.”

3 Press PRESET / to select the preset

number that you want to delete.

If you want to cancel the deleting, press .

4 Press MEMORY to complete the operation.

The preset will be deleted, and the display will

indicate “Deleted!”

1 2

3

2

1

4

2

3

1

11 En

LISTENING TO EXTERNAL SOURCES

English

Selecting preset FM stations

1 Press the FM source button to switch the

audio source to FM.

You can also switch the audio source by pressing RADIO on

the remote control.

2 Press PRESET / to select the FM station

that you want to listen.

You can only select the presets that have been stored.

LISTENING TO EXTERNAL SOURCES

1 Using a commercially available 3.5 mm mini-

plug cable, connect your external device to

the AUX on the rear panel of this unit.

• Turn off the system before connecting the mini-plug cable.

• Turn down the volume of the unit and your external audio

device before connection.

2 Press to turn the system on.

3 Press the AUX source button to switch the

audio source to AUX.

4 Start playback on the connected external

audio device.

1

2

AUX USB

CD iPod

FM

RADIO

1

2

Remote control

Main unit

ON

CLOCK AUX

SET OFF

FM

AUX USB

CD iPod

RADIO

1

2

Rear panel

3

12 En

The unit includes an alarm function (IntelliAlarm) that plays back audio sources or a set of beep (internal alarm sound) at the

set time using a variety of different methods. The alarm function has the following features.

 3 types of alarms

Select from 3 alarm types, combining music and beep sounds.

 Various audio sources

The iPod, audio CD, data CD, USB device and radio can be selected. The following playback methods can also be selected

depending on the audio source:

* For information on creating a playlist, refer to the instructions for your iPod or iTunes.

 Snooze

The snooze function can be enabled to replay the alarm after 5 minutes (☞ P. 14).

By using the free “DTA Controller” application for the iPod touch/iPhone/iPad, you can make detailed alarm settings that

cannot be made using this unit by itself. For each day of the week, you can specify the alarm time (Weekly Alarm) and adjust

the IntelliAlarm as desired.

The front panel display shows information for the Weekly Alarm you’ve set.

For details of “DTA Controller”, refer to the product information in the Yamaha website.

USING THE ALARM FUNCTION

SOURCE+BEEP

The selected audio source and beep sound are played at the set time. This mode is recommended for the best

possible start to the day.

3 minutes before the set time:the source music begins to fade in and the volume gradually increases as the

alarm time approaches.

Alarm time: a beeping sound also begins playing.

SOURCE

The selected audio source is played at the set time. The volume fades in gradually and increases to the set

volume.

BEEP The beep sound is played at the set time.

Source Playback method Function

iPod

Playlist*

A specific playlist stored on the iPod is played back repeatedly. To play a playlist,

create a playlist with the name “ALARM Yamaha DTA” in advance.

When entering the playlist name, use single-byte spaces to separate words, and enter

single-byte characters, taking care that uppercase/lowercase letters are used correctly.

Resume

If the “ALARM Yamaha DTA” playlist cannot be found within the iPod, the unit

resumes play from the last track you played.

Audio CD

Selected track The selected track is played repeatedly.

Resume The track you listened to last time is played back.

Data CD/USB device

Folder The selected folder is played repeatedly.

Resume The track you listened to last time is played back.

FM

Preset station The selected preset station is played.

Resume The FM station you listened to last time is played back.

Using “DTA Controller” to set the alarm

MON TUE WED THU FRI SAT SUN

Monday Tuesday Wednesday Thursday Friday Saturday Sunday

13 En

USING THE ALARM FUNCTION

English

 Set the alarm time and alarm type

Alarm settings cannot be made when the unit is in power saving. If you want to use the alarm function, set the rear panel CLOCK switch to

the ON position.

Setting the alarm

1 Press SET.

The alarm indicator ( ) will blink.

2 Set the alarm.

Set items 1-5 described below.

Press – / + to select a numerical value, and press ENTER to confirm it.

3 Complete the settings.

When you set the VOLUME for item 5, the display will indicate

“Completed!” and your settings will be confirmed. This completes the alarm

setting.

The alarm will be turned on and the alarm indicator ( ) will light.

• By pressing SET during this procedure, you can confirm the alarm settings with the

currently-specified values and complete the procedure.

• If you decide to cancel alarm settings mid-way through the procedure, turn the system off.

1

2

9:12



Completed!

3

Alarm time

Alarm indicator

Items Setting or range

1

ALARM SELECT

*

This can be selected after you’ve used “DTA Controller”

to set the alarm (☞ P. 12). If you’re not using “DTA

Controller,” proceed to item

2

.

ONE DAY: An alarm that sounds only once at the

specified time.

WEEKLY: An alarm whose time can be specified for

each day of the week (settable only using

“DTA Controller”)

If you’ve chosen WEEKLY, this completes the alarm

setting.

2

ALARM TIME

Make settings in the order of hours minutes.

3

ALARM TYPE Select from SOURCE+BEEP, SOURCE or BEEP.

For details, refer to “3 types of alarms” (P. 12).

If you selected BEEP, proceed to item

5.

4

ALARM SOURCE

(If you selected

SOURCE+BEEP or

SOURCE as the

ALARM TYPE)

iPod: Play back music from your iPod (Refer to

“Various audio sources” (P. 12).)

CD: Play back music from a CD.

Specify the track number (data CD: folder

number) (RESUME, 1-99).

USB:

Play back music from a USB device.

Specify the folder number (RESUME, 1-999).

FM: Play a radio station.

Specify the preset number (RESUME, 1-30).

If the selected source cannot be played back at the time

set for the alarm (e.g., the iPod is not connected), the beep

sound is played back.

If you choose RESUME when specifying the track/

folder/preset number, the last-played track/folder/station

will be played (resume playback).

5

ALARM VOLUME

Specifies the volume (5-60) of the alarm.

USING THE ALARM FUNCTION

14 En

 Switching the alarm on/off

When the set time arrives, the selected alarm sound will play. During playback, the following operations are available.

 To pause the alarm (Snooze)

 To turn the alarm off

Press ALARM to turn the alarm on/off.

When the alarm is on, the alarm indicator ( ) will

light, and the alarm time will be shown.

If you press ALARM again, the alarm indicator ( )

and the alarm will turn off.

When the unit is in power saving, the alarm will not function

(☞ P. 5).

Operations while the alarm sound is playing

Press SNOOZE/SLEEP.

Snooze will stop the alarm and play it again 5 minutes

later.

If SOURCE + BEEP is set as the alarm type, you can press

SNOOZE/SLEEP once to stop the beep sound, and twice to

stop the audio source.

Five minutes after the audio source is stopped, it will start fading

in again and the beep sound will resume.

Press ALARM or .

• You can also stop the alarm by holding down SNOOZE/

SLEEP.

• If you don’t stop the alarm, it will stop automatically after 60

minutes and the system will turn off.

• The alarm setting will be saved even if the alarm is turned off.

If the alarm is turned on again by pressing ALARM, the alarm

will sound with the previous alarm settings.

15 En

English

When the specified time has elapsed, the system will turn off automatically.

USING THE SLEEP TIMER

Press SNOOZE/SLEEP repeatedly to specify

the time after which the system will turn off.

You can specify 30, 60, 90 or 120 minutes.

When you select a time, the sleep timer is turned on, and the

sleep indicator ( ) is shown in the front panel display.

If you press

SNOOZE/SLEEP

while the sleep timer is activated,

the sleep timer setting will be canceled.

ADJUSTING THE TONE (remote control only)

1 During playback, press the LOW, MID, or

HIGH EQ button on the remote control.

Select the tone to be adjusted (LOW, MID, HIGH).

2 Press S/T to adjust the tone.

3 Press ENTER on the remote control to

complete the operation.

You can also press the EQ button that you pressed in

Step to complete the settings.

If you want to adjust another frequency band, return to

step and press the EQ button for the frequency

band that you want to adjust.

ADJUSTING THE BRIGHTNESS OF THE FRONT PANEL

DISPLAY (remote control only)

Press DIMMER repeatedly on the remote

control.

The brightness of the front panel display will change in

the order shown below.

AUTO 1 (bright) 2 (medium) 3 (dim)

back to AUTO

When AUTO is set, the brightness of the front panel display is

adjusted automatically with the Illumination sensor (☞ P. 3).

Ensure that the sensor is not covered.

Press repeatedly

1

2

3

1

Press repeatedly

16 En

If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested

solutions or if the problem is not listed below, turn off and unplug the system, and consult the nearest authorized Yamaha

dealer or service center.

TROUBLESHOOTING

General

Problem Cause Solution

The speakers make no sound. The volume might be set to the minimum level,

or muted.

Adjust the volume level.

The source may be incorrect. Select the correct source.

The headphones are connected. Remove the headphones.

The volume of a connected external device is not

loud enough.

Raise the volume of the external device.

Sound suddenly turns off. The sleep timer (☞ P. 15) may be set. Turn the system on and play the source again.

Sound is cracked/distorted or

there is abnormal noise.

Input source volume is excessive, or volume of

this unit is excessive (especially Bass).

Adjust volume with VOLUME, or adjust Bass with EQ

(☞ P. 15). If an external device is playing back, lower the

volume of the external device.

The unit does not operate

properly.

The unit may have received a strong electrical

shock such as lightning or excessive static

electricity, or power supply may have dropped.

Turn the system off, and disconnect the power cable. Wait

about 30 seconds, reconnect the power cable, and turn on

the system.

The system turns on but

immediately shuts off.

A digital or high-frequency

equipment produces noises.

The unit may be placed too close to the digital or

high-frequency equipment.

Place the unit farther away from the equipment.

The clock setting has been

cleared.

The unit remained unpowered for more than one

week.

If the power supply is interrupted for about one week, the

time setting may be reset. If this occurs, please reset the

clock (☞ P. 5).

The iPod does not play back at

the alarm time even if the alarm

source is set to iPod.

The iPod is not set in the iPod dock. Set the iPod in the iPod dock (☞ P. 2) .

Clock flashes and the unit cannot

be operated.

The CLOCK switch is in the SET position, and

the clock settings are in progress.

Set the CLOCK switch to the ON or OFF position.

Alarm does not sound.

The CLOCK switch is in the OFF or SET position.

Set the CLOCK switch to the ON position.

The front panel display indicates

“ALARM not work” and can’t

set the alarm.

The unit turns the system off

unexpectedly.

The automatic system-off function may have

operated.

This unit will turn the system off when 60 minutes have

elapsed without any operation being performed after

stopping playback of the USB device or the CD, or if the

system has been on for 12 hours or more without any

operation being performed.

Front panel display becomes dim. The front panel display’s brightness setting is set

to AUTO.

Change the brightness setting to something other than

AUTO (☞ P. 15). Alternatively, ensure that the

illumination sensor (☞ P. 3) is not obscured.

iPod

Problem Cause Solution

No sound. The iPod is not set in the iPod dock firmly. Remove the iPod from the unit, and then set it in the iPod

dock again (☞ P. 2).

The headphones of the iPod are connected. Remove the headphones.

The iPod software version has not been updated. Download the latest iTunes software to update the iPod

software version to the latest.

The iPod does not charge up. The iPod is not set in the iPod dock firmly. Remove the iPod from the unit, and then set it in the iPod

dock again (☞ P. 2).

USB is selected as the audio source. Select something other than USB as the audio source.

The front panel display indicates

“iPod Unknown” when you

connect the iPod.

The iPod being used is not supported by the unit. Use a supported iPod (☞ P. 19).

17 En

TROUBLESHOOTING

English

CD playback

Problem Cause Solution

CD cannot be inserted. Another disc is already inserted. Unload the disc with EJECT.

You are attempting to insert a disc that cannot be

used by this unit.

Use a disc supported by the unit (☞ P. 18).

Some button operations do not

work.

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 18).

Playback does not start

immediately after pressing

(playback stops immediately.).

The disc may be dirty. Wipe the disc clean.

The disc loaded into the unit may not be compatible.

Use a disc supported by the unit (☞ P. 18).

If the unit was moved from a cold to warm place,

condensation may have formed on the disc

reading lens.

Wait for an hour or two until the unit adjusts to the room

temperature, and try again.

When you insert a disc, the front

panel display indicates “No Disc”

or “CD Unknown.”

The disc loaded into the unit may not be

compatible.

Use a disc supported by the unit (☞ P. 18).

The disc may be dirty, or a foreign object may

have adhered to it.

Wipe the disc clean. Alternatively, remove any foreign

object that has adhered to the disc.

The disc does not contain playable files. Use a disc containing playable files (☞ P. 18).

The disc was inserted upside down. Insert the disc with the label facing upward.

The front panel display indicates

“no operation”, and a disc cannot

be inserted or unloaded.

The clock/alarm/tone settings are in progress.

Alternatively, the alarm is playing.

Complete the clock/alarm/tone settings. Alternatively, stop

the alarm.

USB device playback

Problem Cause Solution

MP3/WMA file on the USB

device does not play.

The USB device is not recognized. Turn the system off and disconnect the USB device.

Then turn the system on and reconnect the USB device to

the unit.

If the solutions above do not resolve the problem, the USB

device is not playable on the unit (☞ P. 18).

The USB device does not contain playable files. Use a USB device contains playable files (☞ P. 18 ).

When you connect a USB device,

the front panel display indicates

“USB OverCurrent,” and then

the front panel display goes

blank.

An incompatible USB device is connected to the

unit. Alternatively, the USB device is not connect

firmly to the unit.

Turn the system off and disconnect the USB device.

Then turn the system on and reconnect the USB device to

the unit.

If the solutions above do not resolve the problem, the USB

device is not playable on the unit (☞ P. 18).

FM reception

Problem Cause Solution

Too much noise. The antenna may be connected improperly. Make sure the antenna is connected properly (☞ P. 3) or

use a commercially available outdoor antenna.

The antenna is too close to the unit or to an

electronic device.

Position the antenna as far away as possible from the unit

or the electronic device.

Too much noise during stereo

broadcast.

The radio station you selected may be far from

your area, or the radio wave reception is weak in

your area.

Try manual tuning to improve the signal quality (☞ P. 9) or

use a commercially available outdoor antenna.

Even with an outdoor antenna,

radio wave reception is weak.

(Sound is distorted.)

Multipath reflection or other radio interferences

may have occurred.

Change the height, direction, or placement of the antenna.

Remote control

Problem Cause Solution

The remote control does not work

properly.

The remote control may be operated outside its

operation range.

For information on the remote control operation range,

refer to “How to use the remote control” (P. 1).

The remote control signal receiver on the unit

(☞ P. 3) may be exposed to direct sunlight or

lighting (inverted fluorescent lamps).

Change the lighting or orientation of the unit.

The battery may be worn out. Replace the battery with new one (☞ P. 1 ).

There are obstacles between the remote control

signal receiver on the unit (☞ P. 3) and the

remote control.

Remove the obstacles.

18 En

This unit is designed for use with audio CD, CD-R*, and

CD-RW* with the logos followings.

* ISO 9660 format CD-R/RW

This unit can play back discs bearing any of the logo marks above.

A disc logo mark is printed on the disc and the disc jacket.

• Do not load any other type of disc into this unit. Doing so may

damage this

unit.

• CD-R/RW cannot be played back unless finalized.

• Some discs cannot be played back depending on the disc

characteristics or recording conditions.

• Do not use any non-standard shaped discs such as a heart-shaped

disc.

• Do not use discs with many scratches on their surface.

• Do not load a cracked, warped, or glued disc.

• Do not use 8-cm discs.

• Do not touch the surface of the

disc. Hold a disc by its edge (and

the center hole).

• Do not use a pencil or pointed

marker to write on the disc.

• Do not put a tape, seal, glue, etc., on a disc.

• Do not use a protective cover to prevent scratches.

• Do not load more than one disc into this unit at one time.

This can cause damage to both this unit and the discs.

• Do not insert any foreign objects into the disc slot.

• Do not expose a disc to direct

sunlight, high temperature,

high humidity, or a lot of dust.

• If a disc becomes dirty, wipe it

with a clean, dry cloth from the

center out to the edge. Do not

use record cleaner or paint

thinner.

• To avoid malfunction, do not

use a commercially available

lens cleaner.

This unit supports USB mass storage class

devices (e.g.,

flash memories or

portable audio pl

ayers) using FAT16 or

FAT32 format.

• Some devices may not work properly even if they meet the

requirements.

• Do not connect devices other than USB mass storage class

devices (such as USB chargers or USB hubs), PCs, card readers,

an external HDD, etc.

• Yamaha will not be held responsible for any damage to or data

loss on the USB device occurring while the device is connected

to this unit.

• Playability of and power supply to all kind of USB devices are

not guaranteed.

• USB devices with encryption cannot be used.

• The unit can play back:

** Both constant and variable bitrates are supported.

• T

he maximum numbers of files/folders that can be played on the

unit are as follows.

• Copyright-protected files cannot be played back.

NOTES ON DISCS AND USB DEVICES

CD information

Handling a disc

Caution

USB device information

About MP3 or WMA files

File Bitrate (kbps)

Sampling

frequency (kHz)

MP3 8-320** 16-48

WMA 16-320** 22.05-48

Data CD USB

Maximum total number of file 512 9999

Maximum folder number 255 999

Maximum file number per folder 511 255

Sayfa yükleniyor...

Yamaha TSX-132 Black Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha TSX-132 Black Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler