Whirlpool ADS93D 69 EU/B Kullanici rehberi

Marka: Whirlpool

Model: ADS93D 69 EU/B

Kategori: Çamaşır makineleri

Tip: Kullanici rehberi

English,1

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Description of the machine, 4-5

Touch control panel

Auto Dose System, 6-7

Running a wash cycle, 8

Wash cycles and options, 9

Table of wash cycles

Wash options

Detergents and laundry, 10

Detergent

Preparing the laundry

Washing recommendations

Precautions and advice, 11

General safety

Load balancing system

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 13-14

Assistance, 15

WASHING MACHINE

AQUALTIS

ADS93D 69

Instructions for

installation and use

Türkçe,33

TRGR

ΕΛΛΗΝΙΚΑ, 17

Українська,49

Installation

! This instruction manual should be kept in a safe place for future

reference. If the washing machine is sold, given away or moved,

please ensure the manual is kept with the machine, so that the

new owner may benefit from the advice contained within it.

! Read these instructions carefully: they contain vital information

relating to the safe installation and operation of the appliance.

! Inside the pack containing this manual, you will also find

the guarantee and all the details necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging from the

washing machine, make sure it has not been damaged during

transportation.

If it has been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4 protective

screws (used during

transportation) and the

corresponding spacer,

located on the rear part of

the appliance (see figure).

3. Close off the holes using the plastic plugs supplied in the pack.

4. Keep all the parts in a safe place; they will be needed

again if the washing machine is moved to another

location, to prevent the inside of the appliance being

damaged.

! Packaging materials should not be used as toys for

children.

Levelling

1. Place the washing machine on a flat sturdy floor, without

resting it up against walls or cabinets.

2. If the floor is uneven, the

front feet of the machine

may be adjusted until

it reaches a horizontal

position (the angle of

inclination must not exceed

2 degrees).

! If the appliance is levelled correctly, it will be more stable

and much less likely to cause vibrations and noise while it is

operating, particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space underneath

the washing machine.

Connecting the electricity and water

supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water supply, run

the water until it is perfectly clear.

1. Connect the inlet hose

to the machine by screwing

it onto the cold water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part of

the appliance (see figure).

2. Connect the inlet hose by

screwing it to a cold water

tab using a 3/4 gas threaded

connection (see figure).

3. Make sure that the hose is not folded over or bent.

! The water pressure at the tap must fall within the values

indicated in the Technical data table (see next page).

! If the inlet hose is not long enough, contact a specialised

shop or an authorised technician.

! Never use second-hand or old inlet hoses; use the

products supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain hose to

drain duct piping or a wall

drain located between 65

and 100 cm above the floor,

making sure it is not bent at all.

Alternatively, rest the

drain hose on the side of

a washbasin or bathtub,

fastening the duct supplied

to the tap (see figure).

The free end of the hose

should not be underwater.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the same

diameter as the original hose and must not exceed 150 cm

in length.

Electrical connections

Before plugging the appliance into the electricity socket,

make sure that:

• thesocketisearthedandcomplieswithallapplicable

laws;

• thesocketisabletowithstandthemaximumpowerload

of the appliance as indicated in the Technical data table

(see opposite);

• thepowersupplyvoltagefallswithinthevaluesindicated

in the Technical data table (see opposite);

• thesocketiscompatiblewiththeplugoftheappliance.

If this is not the case, have the socket or the plug

replaced.

! The machine must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain, storms and other weather

conditions.

! The mains socket must remain within easy reach after the

washing machine has been installed.

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

! The power supply cable and plug must only be replaced

by authorised technicians.

Warning! The company shall not be held responsible in the

event that these regulations are not respected.

Technical data

Model

ADS93D 69

Dimensions

width 59.5 cm

height 85 cm

depth 64,5 cm

Capacity

from 1 to 9 kg

Electrical

connections

please refer to the technical data plate

fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1600 rotations per minute

Test wash cycles

in accordance

with directives

1061/2010 and

1015/2010

programme

; temperature 60°C;

programme

; temperature 40°C;

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compa-

tibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside

the machine and can be

accessed by opening the

door.

Refer to the chapter “Auto

Dose System” for information

on operation.

TOUCH CONTROL PANEL

To adjust the settings, gently

press the icon inside the

sensitive (touch control) area

as illustrated in the figure.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly and

wait for the machine to start up again.

Consumption in off-mode: 1 W

Consumption in Left-on: 1 W

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

WASH CYCLE

SELECTOR knob

Button with ON/OFF

indicator light

Touch control panel

TEMPERATURE

button

OPTION

buttons

DISPLAY

ECO

indicator light

START/PAUSE button

with indicator light

LOCK

indicator light

WASH CYCLE

PHASE icons

SPIN SPEED

button

DELAY

TIMER button

CHILD LOCK button

with indicator light

Button with ON/OFF indicator light: press this briefly to switch

the machine on or off. The green indicator light indicates that the

machine is switched on. To switch off the washing machine during

the wash cycle, press and hold the button for approximately

3 seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off during

a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in either

direction. To select the most suitable wash cycle, please refer

to the “Table of wash cycles”.

The knob will not move during the wash cycle.

TEMPERATURE button: press to modify or exclude the

temperature setting; the value selected will appear on the display

above (see “Running a wash cycle”).

SPIN SPEED CYCLE button: press to modify or exclude the

spin cycle; the value selected will appear on the display above

(see “Running a wash cycle”).

DELAY TIMER button: press to set a delayed start for the

selected wash cycle; the set delay time will appear on the display

above (see “Running a wash cycle”).

OPTION buttons with indicator lights: press to select the available

options. The indicator light corresponding to the selected option

will remain lit (see “Running a wash cycle”).

DETERGENT and SOFTENER buttons : refer to

“Modifying pre-set parameters” in the chapter “Auto Dose System”.

DETERGENT DILUTION button: refer to “Filling the tanks”

in the chapter “Auto Dose System”.

WASH CYCLE PHASE icons: these illuminate to indicate the

progress of the wash cycle (Wash – Rinse – Spin –

Drain ). The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a wash

cycle. Once the cycle has begun the indicator light will remain

lit in a fixed manner. To pause the wash cycle, press the button

again; the indicator light will flash in an orange colour.

If the “LOCK” indicator light is switched off, the door may be

opened. To start the wash cycle from the point at which it was

interrupted, press the button again.

LOCK indicator light: indicates that the porthole door is

locked. To open the door, pause the wash cycle (see “Running

a wash cycle”).

CHILD LOCK button with indicator light: to activate or

deactivate the control panel lock, press and hold the button for

approximately 2 seconds. when the indicator light is illuminated,

the control panel is locked. This means it is possible to prevent

wash cycles from being modified accidentally, especially where

there are children in the home.

ECO indicator light: the icon lights up when, after altering the

washing parameters, an energy saving of at least 10% is made.

Furthermore, before the machine enters “Standby” mode, the

icon will light up for a few seconds; when the machine is switched

off the estimated energy saving will be around the 80% mark.

CHANGE LANGUAGE

The first time the machine is switched on, the first language

will flash on the display. The

“ “, “OK” and “V” symbols will appear on the display, in line

with the 3 buttons on the right-hand side. The languages

change automatically every 3”; alternatively, they can be

changed by pressing the buttons next to the “ “ and “V”

symbols. Use the “OK” button to confirm the language, which

will be set after 2”. If no buttons are pressed, the automatic

language change will begin again after 30”.

To change the language, switch the machine on and off

again; in the 30” time period after it has been switched

off, press and hold the temperature +spin

+delayed start buttons simultaneously for 5’’. A short

sound alert will be emitted and the set language will flash

on the display. Press the buttons next to the “ “ and “V”

symbols to change the language. Use the button next to the

“OK” symbol to confirm the language, which will be set after

2”. If no buttons are pressed, the language set previously will

be displayed after 30”. Switch on the machine.

DETERGENT

button

SOFTENER

button

DETERGENT

DILUTION

button

Auto Dose System

Introduction

This washing machine is

equipped with two tanks: one

for liquid detergent (either

concentrated or diluted) with

a capacity of approx. 5.5 l

and another for liquid fabric

softener (either concentrated

or diluted) with a capacity of

approx. 3.5 l (see picture).

! Check the detergent/fabric

softener box to verify whether

it is diluted or concentrated

detergent. The automatic

dosing system intakes the

correct amount of detergent and fabric softener from the

tanks for each type of load and at the right time, guaranteeing

optimal washing results without wastage. The amount of

detergent/fabric softener can be modified manually by

pressing the DETERGENT and FABRIC SOFTENER buttons

(refer to “Modifying pre-set parameters”). If you prefer, the

washing machine can also be used in the “traditional” mode,

i.e. by adding the detergent in the dispenser; the machine will

automatically detect the detergent and will not use the tanks.

Detergent dispenser

“Traditional” mode.

Pull out the detergent dispenser drawer up to the first stop

point to add the detergent (either liquid or powder detergent),

bleach or other additives (e.g. whiteners) and the pre-wash

detergent for washing in the “traditional” mode (refer to

“Traditional” mode).

“Auto Dose System” mode.

In order to fill the detergent

and fabric softener tanks, the

detergent dispenser drawer

must be fully extracted:

open the dispenser drawer

up to the first stop point then

press the lever (A) and open

up to the second stop point,

making sure that it is fully

extracted. Avoid moving

the dispenser drawer during

filling operations. Once the tanks have been filled (refer to

“Filling the tanks”), the machine can run up to 40 cycles before

the detergent finishes (*).

First-time use

Turn the washing machine on by pressing the ON/OFF button.

The first wash cycle must be carried out without laundry

and by adding detergent in the detergent dispenser (refer

to “Traditional” mode); set the programme “ “ (Cotton 90°)

without pre-wash and without filling the tanks.

Filling the tanks:

Open the detergent dispenser drawer in the “Auto Dose

System” mode (refer to “Detergent dispenser”).

Slowly pour the detergent (B) and fabric softener (C)

until the tanks are completely filled (see picture).

To avoid exceeding the maximum capacity, a buzzer (beep)

will sound with growing intensity to signal the level and 3 long

beeps will sound once the tank is completely full.

Start the wash cycle immediately after filling the tanks to

ensure that the dispenser is properly cleaned.The respective

icons (for the detergent) and (for the fabric softener) will

light up gradually to signal the level.

The filling time depends on the density of the product. Very

dense products will take longer to fill.

Close the detergent dispenser drawer only once the

compartments are completely empty.

Select the density of the detergent added (either concentrated

or liquid) by pressing the appropriate button .

Concentrated

Diluted

The machine will store the selection.

If no option is selected, the detergent intake option will be

pre-set to “diluted”.

Use button to set the amount of fabric softener that will

be automatically extracted by the machine:

1) If concentrated softener is used, we recommend selecting

the first level ( with one bar) and, if necessary, stepping up

by a single position ( with 2 bars) to increase detergent

intake.

2) If diluted softener is used, we recommend setting level

3 ( with 3 bars) and to then either increase/decrease the

amount of fabric softener to be extracted.

3) To exclude the use of fabric softener, press until the

bars disappear (also refer to “Modifying pre-set parameters”).

(*) with an average load of 4 kg, 40°C Cotton programme, “medium” water hardness

level and dirt level set to 3.

Signals for successive refilling:

Once, at the end of a cycle, the level of detergent/fabric

softener falls below the level required for a successive

wash cycle, the display will visualise the relative messages

“At end of cycle refill detergent” or “At end of cycle refill

softener” or “At end of cycle refill tanks”. If the tanks are

not filled, the successive wash cycles in Auto Dose System

will be carried out without any intake of detergent.

! We suggest adding detergent and fabric softener ONLY

after the machine’s signal.

! NEVER mix two different detergents; always clean out

the tank before adding a new type of detergent (refer to

“Cleaning cycle set by the user”).

Using the “Auto Dose System”

If the compartments have been filled with detergent and

fabric softener, you may start using the machine (refer to

“Running a wash cycle”).

Powder detergents for pre-washing and powder

additives may only be used in the traditional mode or

using the “Auto Dose System”, by placing the additives

directly inside the drum, preferably in conjunction with the

“laundry ball”.

Whenever bleaching is required, pour the bleach in the

relative compartment (refer to the option “Super Wash”).

Modifying pre-set parameters:

The machine automatically intakes detergent on the

basis of the selected programme, wash load and water

hardness. However, the amount of detergent/fabric

softener used may be modified.

button: press to increase, decrease and to exclude

detergent intake.

button: press to increase, decrease and to exclude

fabric softener intake.

The level of detergent/fabric softener suggested by the

machine is indicated by 3 bars.

Less than 3 bars indicates a lower level of detergent/

fabric softener compared to that suggested by the

machine, while more than 3 bars indicates a higher level of

detergent/fabric softener.

Cleaning the tanks:

Tank cleaning cycles can either be automatic or pre-set by

the user.

Automatic cleaning:

The washing machine carries out an automatic cleaning

cycle during the rinse cycle if the level of detergent that

remains is insufficient for carrying out a

successive wash cycle.

Cleaning cycle set by the user:

Run the cleaning cycle (with empty drum) if you require

adding a different product to the previous one or if the tanks

have been incorrectly filled (e.g. fabric softener has been

erroneously poured into the detergent tank or vice-versa).

Press button and hold for 5 sec. to activate cleaning of

the detergent tank, button for cleaning the fabric softener

tank or button for cleaning both tanks. Keep pressing for

a further 3 sec. (the countdown “4-3-2-1” will appear in the

top right corner) until “CLEAN-GO” pops up.

The cleaning cycle lasts about 40’ if the tanks are initially

empty; if not, the cycle will last longer. The icons indicating

that the tanks are empty will appear on the display.

“Traditional” mode

Pull out the detergent dispenser drawer up to the first stop

point (see picture) then pour the amount of detergent and

other additives (e.g. bleach) required for a single wash cycle

directly into the dispenser.

1. pre-wash compartment: use

powder detergent only.

2. main wash compartment:

use powder or liquid detergent.

If the lat ter is used, we

recommend pouring it into the

dispenser immediately before

starting the washing machine

and without running a pre-

wash cycle.

3. bleach compartment: to be used whenever bleaching is

required (refer to “Super Wash” option).

Tablet detergent or the relative “laundry ball” must be added

directly inside the drum. In this event, deactivate the “Auto

Dose System” (by pressing the button until the relative

vertical bars disappear from the display).

Do not pour any fabric softener as the appropriate quantity

required for each wash cycle will be automatically extracted.

To deactivate fabric softener intake, press the button until

the vertical bars disappear from the display.

For wool and silk garments, we recommend using a special

detergent which must be poured directly into the detergent

dispenser (compartment 2).

Running the wash cycle:

Select the programme and the compatible options on the

basis of the required need and type of load.

Running a wash cycle

WARNING: before you use the washing machine for the first

time, run a wash cycle with detergent and no laundry, using

the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the button. All

the indicator lights will illuminate for 1 second and the text

AQUALTIS will appear on the display; the indicator light

corresponding to the button will then remain lit in a constant

manner and the START/PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has been

selected; the name of the programme will appear on the

display. A temperature and spin speed is set for each

programme; these may be adjusted. The cycle duration

will also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door. Load the

laundry, making sure you do not exceed the maximum load

value indicated in the table of wash cycles on the following

page.

4. MEASURE OUT THE DETERGENT. There is no need

to add detergent when the “Auto Dose System” mode is

used, as the machine automatically intakes detergent on the

basis of the selected programme, type of load and water

hardness. Refer to the paragraph “Traditional” mode for

implementing the traditional operation mode.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum

temperature and spin speed values set for the selected

cycle, or the most recently-used settings if they are

compatible with the selected cycle. The temperature

can be decreased by pressing the button, until the

cold wash “OFF” setting is reached. The spin speed may

be progressively reduced by pressing the button,

until it is completely excluded “OFF”. If these buttons

are pressed again, the maximum values are restored.

! Exception: if the programme is selected, the temperature

can be increased up to a value of 90°C.

Set a DELAY TIMER.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. During the setting procedure, the

delay period and the text “Starts in:” will be displayed, along

with the flashing symbol. After the delayed start has been

set, the symbol will remain fixed on the display, which will

also indicate the duration of the selected cycle with the text

“Ends in:” and the cycle duration. Press the DELAY TIMER

button just once to display the delay time set previously. After

the countdown has begun, the display will show the text

“Starts in:” and the delay period.

Once the set delay time has elapsed, the machine will begin

its cycle and the display will show “Ends in:” and the time

remaining until the end of the cycle. To remove the delayed

start option, press the button until the display shows the text

OFF; the symbol will disappear.

Modify the cycle settings.

•Press the button to activate the option; the name of the

option will then appear on the display and the corresponding

indicator light will illuminate.

•Press the button again to deactivate the option; the name

of the option will then appear on the display followed by

the text OFF, and the corresponding indicator light will

switch off.

! If the selected option is not compatible with the selected

wash cycle, this incompatibility will be signalled by the

flashing of the indicator light and a sound alert (3 beeps);

the option will not be activated.

! If the selected option is not compatible with another option

that has been selected previously, the indicator light

corresponding to the first option selected will flash and

only the second option will be activated; the indicator light

corresponding to the button will remain lit in a constant

manner.

! The options may affect the recommended load value and/or

the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in a

fixed manner and the porthole door locks (the LOCK

indicator light illuminates). The icons corresponding to

the wash cycle phases will light up during the cycle to

indicate which phase is currently in progress. To change a

wash cycle once it has already started, pause the washing

machine by pressing the START/PAUSE button; then select

the desired cycle and press the START/PAUSE button

again. To open the door during a wash cycle, press the

START/PAUSE button; if the LOCK indicator light is

switched off you may open the door. Press the START/

PAUSE button again to restart the wash cycle from the

point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated by

the illuminated text END. The porthole door may be opened

immediately. If the START/PAUSE indicator light is flashing,

press the button to end the cycle. Open the door, unload

the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the button until the cycle stops and the machine

switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to wash

even the most valuable and delicate garments in complete

confidence thanks to the special bag which protects the

laundry (this is supplied with the machine). We recommend

that the bag is used every time you wash quilts and

padded items with an outer layer made using synthetic

material.

Wash cycles and options

Wash options

Super Wash

This option offers a high-

performance wash due to

the greater quantity of water

used in the initial phase of

the cycle, and due to the

increased wash cycle duration,

is particularly useful for the

removal of stubborn stains. It

can be used with or without

bleach. If you desire bleaching,

use the compartment 3.

When dosing the bleach,

be careful not to exceed the “max” level (see figure).

To bleach laundry without carrying out a full wash cycle,

pour the bleach into the compartment 3, select the “Rinse”

cycle and activate the “Super Wash” option .

! It cannot be used in conjunction with , , , , , ,

, , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased

and optimal residual detergent removal is guaranteed. It is

particularly useful for skin which is sensitive to detergents. We

recommend this option is used with a full load of washing, or

when a large amount of detergent is required.

! It cannot be used in conjunction with , , , , .

Easy Iron

By selecting this option, the wash and spin cycles will

be modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will rotate

slowly; the “Easy Iron” and START/PAUSE indicator lights will flash.

To end the cycle press the START/PAUSE button or the “Easy

Iron” button.

! It cannot be used in conjunction with , , , , .

Time Saver

If you select this option, the wash cycle duration will be

reduced by up to 50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

! It cannot be used in conjunction with , , , ,

, , , , .

Table of wash cycles

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value will then be shown on the display.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary according to factors such as

water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

For all Test Institutes:

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for garments which can be

washed at 40°C. The actual washing temperature may differ from the indicated value.

3) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.

4) Short wash cycle for cottons: set wash cycle with a temperature of 40°C.

5) Long wash cycle for synthetics: set wash cycle with a temperature of 40°C.

Icon Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergent and addi-

tives

Max. load (kg)

Residual dam-

pness %

Energy con-

sumption kWh

Total water lt

Cycle duration

Prewash

Wash

Bleach

Fabric

softener

Cotton Coloureds (2-3): lightly soiled whites and delicate colours. 40° 1600 -

  

9 44 1,09 92 185’

Synthetics Resistant 60° 800 -

  

4 46 1,03 60 110’

Synthetics Resistant (5) 40° 800 -

  

4 46 0,56 60 95’

Whites

60° 1600 -



5 - - - 180’

Coloureds (4)

40° 1600 -

  

5 44 0,83 63 100’

Darks

30° 800 -



5 - - - 75’

Shirts

40° 600 -

  

2 - - - 69’

Duvets: for down-stuffed garments. 30° 1200 -



3,5 - - - 120’

Bed&Bath for bedlinen and towels. 60° 1600 -

  

9 - - - 140’

Rinse

- 1600 - -

 

9 - - - 36’

Spin and Pump out - 1600 - - - - 9 - - - 16’

Anti Allergy

60° 1600 -



5 - - - 195’

Ultradelicates

30° 0 -



1 - - - 80’

Wool: for wool, cashmere, etc. 40° 800 -



2 - - - 88’

Mix 30': to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800 -



3,5 71 0,20 38 30’

Cotton Hygiene Prewash

(Add detergent to the relevant compartment).

90° 1600

 



9 44 2,86 98 195’

Cotton Whites (1): heavily soiled whites and resistant colours. 60° 1600 -

  

9 44 1,54 76 188’

Cotton Whites: heavily soiled whites and resistant colours. 90° 1600 -

  

9 44 2,54 85 181’

Shirts: use the special wash cycle to wash shirts in

different fabrics and colours to guarantee they receive the

best possible care.

Duvets: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

special wash cycle. We recommend that duvets are

placed in the drum with their edges folded inwards (see

figure) and that no more than ¾ of the total volume of the

drum is used. To achieve the best results, we recommend

that a liquid detergent is used and placed inside the

detergent dispenser drawer.

Quilts: to wash quilts with a

synthetic outer layer, use the bag provided and set the

wash cycle to .

Bedlinen and towels: Use programme to wash bed

linen and towels in one single cycle: it optimises softener

performance and helps you save time and energy. We

recommend the use of powder detergent

Anti Allergy: use programme to remove major allergens

such as pollen, mites, cat’s and dog’s hair.

Ultradelicates: use programme to wash very delicate

garments having strasses or sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

To wash Silk garments and Curtains (these should be

folded and placed inside the bag provided), select cycle

and then option ; the machine will end the cycle while

the laundry is soaking and the indicator light will flash.

To drain the water so that the laundry may be removed,

press the START/PAUSE button or the button.

Wool: the wool wash cycle on this Hotpoint-Ariston

machine has been tested and approved by The

Woolmark Company for washing wool garments labelled

as hand washable provided that the garments are

washed according to the instructions on the garment

label and those issued by the manufacturer of this

washing machine. Hotpoint-Ariston is the first washing

machine brand to be approved by The Woolmark

Company for Apparel Care- Platinum for its washing

performance and consumption of energy and water.

(M1127)

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

Detergents and laundry

Detergent

The type and quantity of detergent required depend on the

type of fabric you are washing (cotton, wool, silk, etc.), as

well as its colour, the washing temperature, the level of soiling

and the hardness of the water in the area.

Whenever the detergent and fabric softener “Auto Dose

System” is activated, this washing machine helps to

prevent wastage and to protect the environment, besides

guaranteeing optimal washing performance.

We recommend the following:

• Usepowder detergentfor carrying out a pre-washand

pour in the “traditional” mode.

• Useliquiddetergentsfordelicatecottongarmentsandfor

all low-temperature wash cycles.

• Whenactivatingthe“Auto Dose System” mode, use liquid

detergent and fabric softeners only. Never add ultra-

concentrated detergents (e.g. “Gel” type detergents

or similar).

• Usegentleliquiddetergentsforwoolandsilk garments

and pour in the “traditional” mode.

! Never mix two different detergents; always clean out the

tank before adding a new type of detergent.

The detergent should be poured into the relevant compartment

- or the dispenser placed directly inside the drum - before the

wash cycle begins. In the latter case, it will not be possible

to select the Cottons with pre-wash cycle.

! Use powder detergent for white cotton garments, for

pre-washing, and for washing at temperatures over 60°C

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the

machine.

• Dividethelaundryaccordingfabrictype(symbolonthe

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Emptyallpocketsandcheckthebuttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Whites: use this cycle to wash white clothes. The

programme is designed to maintain the brightness of

white clothes over time.

Coloureds: use this cycle to wash bright coloured

clothes. The programme is designed to maintain bright

colours over time.

Darks: Use cycle to wash dark-coloured garments.

This programme is designed to maintain dark colours

over time. We recommend using a liquid detergent for the

best results when washing dark-coloured garments.

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water using

the drain hose, collecting it in

a bucket as indicated in the

figure.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is freed

from its stop position; pull

downwards until you hear a

“click”, which indicates that the

door is now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Precautions and tips

! The machine was designed and constructed in accordance

with international safety regulations. The following information

is provided for safety reasons and must therefore be read

carefully.

General safety

• Thisapplianceisnotintendedforusebypersons(including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not

play with the appliance.

• Thisappliancewasdesignedfordomesticuseonly.

• Donottouchthemachinewhenbarefootorwithwetor

damp hands or feet.

• Donotpullonthepowersupplycablewhenunplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Donottouchthedrainedwaterasitmayreachextremely

high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Alwayskeepchildrenwellawayfromtheappliancewhile

it is operating.

• Ifitmustbemoved,proceedwiththehelpoftwoorthree

people and handle it with the utmost care. Never try to do

this alone, because the appliance is very heavy.

• Beforeloadinglaundryintothewashingmachine,make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations before

every spin and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly greater

than the washing rotation speed. If, after several attempts, the

load is not balanced correctly, the machine spins at a reduced

spin speed. If the load is excessively unbalanced, the washing

machine performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using

the normal solid urban waste cycle. Exhausted appliances

Cutting off the water and electricity

supplies

• Turnoffthewatertapaftereverywashcycle.Thiswill

limit wear on the hydraulic system in the machine and

help to prevent leaks.

• Unplugtheappliancewhencleaningitandduringall

maintenance work.

Cleaning the machine

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

To pull out the dispenser drawer, open until the first stop point

then press lever A to open completely; finally, press one of the

levers D and pull the drawer outwards (see picture).

Wash it under running water; this procedure should be

effected regularly. Be careful to remove any detergent residues

from the dispenser drawer socket on the machine.

Keep the drawer to the left hand side when replacing it

to ensure that it centres the guides and to prevent it from

jamming.

Caring for your appliance drum

• Alwaysleavethedoorajartopreventunpleasantodours

from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and unplug the

appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the machine by

first pressing it in the centre and then pushing downwards

on both sides until you can remove it (see figures);

2. position a container so that

it will collect the water which

flows out (approximately 1.5 l)

(see figure);

3. unscrew the lid by rotating

it in an anti-clockwise

direction (see figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are any

cracks, it should be replaced immediately: during the wash

cycles, water pressure is very strong and a cracked hose

could easily split open.

Care and maintenance

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be not solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water.

The washing machine door

remains locked.

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The icons corresponding to the

“Phase in progress” flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washing machine door

remains locked.

“AutoDose disabled, use the

dispenser drawer” appears on the

display.

Possible causes / Solutions:

• Theapplianceisnotpluggedintothesocketfully,ornotenoughtomake

contact.

• Thereisnopowerinthehouse.

• Thedoorisnotclosedproperly.

• TheSTART/PAUSEbuttonhasnotbeenpressed.

• Thewatertaphasnotbeenopened.

• Adelayedstarthasbeenset.

• Thewaterinlethoseisnotconnectedtothetap.

• Thehoseisbent.

• Thewatertaphasnotbeenopened.

• Thereisnowatersupplyinthehouse.

• Thepressureistoolow.

• TheSTART/PAUSEbuttonhasnotbeenpressed.

• Ifyouhaveselectedthe function, at the end of the cycle the washing

machine drum will rotate slowly; to end the cycle press the START/PAUSE

button or the button.

• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor

(see “Installation”).

• Thefreeendofthehoseisunderwater(see “Installation”).

• Ifthedwellingisononeoftheupperfloorsofabuilding,theremaybe

problems relating to water drainage, causing the washing machine to fill with

water and drain continuously. Special anti-draining valves are available in shops

and help to prevent this inconvenience.

• Thewalldrainagesystemisnotfittedwithabreatherpipe.

• Thewashcycledoesnotincludedraining:Somewashcyclesrequirethedrain

phase to be started manually (see “Wash cycles and options”).

• The“Easyiron”optionisenabled:tocompletethewashcycle,pressthe

START/PAUSE button (“Wash cycles and options”).

• Thedrainhoseisbent(see Installation).

• Thedrainageductisclogged.

• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).

• Themachineisnotlevel(see “Installation” ).

• Themachineistrappedbetweencabinetsandwalls(see “Installation”).

• Theloadisunbalanced(see “Detergents and laundry”).

• Thewaterinlethoseisnotscrewedonproperly(see“Installation”).

• Thedetergentdispenserisblocked(tocleanit,see “Care and maintenance”).

• Thedrainhoseisnotfixedinplaceproperly(see“Installation”).

• Switchoffthemachineandunplugit,waitforapproximately1minuteand

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext

“for washing machines” or “hand and machine wash”, or the like).

• Toomuchdetergentwasused.

• Performthemanualunlockingprocedure(see “Precautions and tips”).

• IndicatesmalfunctioningoftheAutoDosesystem.Usethemachinetraditionally,

by pouring the detergent and fabric softener required for a wash cycle into

the drawer, and contact the Assistance service to establish the cause(s) of the

malfunction.

Troubleshooting:

The machine’s washing performance

is unsatisfactory.

What happens if the tanks are loaded

even if they are already full?

What happens if the dispenser is used

in the traditional mode while the tanks

are still full?

Can the tanks also be used for

powder detergent?

Can powder detergent fall into the

tanks?

What happens if the dispenser is

not opened properly when filling the

tanks?

What happens if detergent and fabric

softener are erroneously inverted?

What happens if different detergents

are mixed before the tanks are

empty?

Possible causes / Solutions:

•Thetankshavenotbeenloadedcorrectly(e.g.fabricsoftenerhasbeen

added instead of detergent or vice-versa)

•Twodifferenttypesofdetergent/fabricsoftenerhavemixed.

! NEVER mix two different detergents; always clean out the tanks before adding

a new type of detergent.

•The“Auto Dose System” is blocked due to prolonged lack of use: carry out

a tank cleaning cycle (refer to “Cleaning cycle set by the user”).

•Buzzers(Beep)andvisualsignals(iconsappearingonthedisplay)indicate

that the tank is full. If further detergent/fabric softener is added, the excess

quantity will fall into the drum and will be washed away with the next cycle.

•Themachinewillautomaticallytrackwhetherpowderorliquiddetergent

has been loaded in the traditional mode and will not intake any amount of

detergent from the tank. Fabric softener can only be used in the “Auto Dose

System” mode.

•No,powderdetergentcanonlybeusedinthetraditionalmode.

•No,thereisabarriertopreventpowderdetergentfromfallingintooneof

the tanks even if the dispenser is open in the “Auto Dose System” position

(i.e. completely open).

•Ifthedispenserisnotcompletelyopen,thedetergentorfabricsoftenerthat

has been added will fall into the drum and will be washed away with the

next cycle.

•Thewashingmachinewillwashwithunsatisfactoryresults,thetankswill

have to be emptied and subjected to a manual cleaning cycle.

•Themachinewillwashnormallyalthoughwerecommendonlyrefilling

the tanks after the signal emitted by the machine; do not mix different

detergents/fabric softeners.

! Note: to exit “Demo mode”, switch machine off, press and hold the two “START/PAUSE” and “ON/OFF” buttons

simultaneously for 3 seconds.

Assistance

Before calling for Assistance:

• Checkwhetheryoucansolvetheproblembyyourself(see“Trouble shooting”);

• Restartthewashcycletocheckwhethertheproblemhasbeensolved;

• Ifithasnot,contacttheAuthorisedTechnicalAssistanceService.

! If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.

! Always request the assistance of authorised technicians.

Please have the following information to hand:

• thetypeofproblem;

• theappliancemodel(Mod.);

• theserialnumber(S/N).

The above information can be found on the data plate located on the appliance itself.

Ελληνικά

Περιεχόμενα

Εγκατάσταση, 18-19

Αποσυσκευασία και οριζοντίωση

Υδραυλικές και ηλεκτρικές συνδέσεις

Τεχνικά στοιχεία

Περιγραφή της μηχανής, 20-21

Πίνακας χειριστηρίων touch control

Auto Dose System, 22-23

Πως διενεργείται ένας κύκλος πλυσίματος,24

Προγράμματα και δυνατότητες, 25

Πίνακας Προγραμμάτων

Οι δυνατότητες πλυσίματος

Απορρυπαντικά και μπουγάδα, 26

Απορρυπαντικό

Προετοιμασία της μπουγάδας

Συμβουλές πλυσίματος

Προφυλάξεις και συμβουλές, 27

Γενική ασφάλεια

Σύστημα ισοστάθμισης του φορτίου

Διάθεση

Χειρονακτικό άνοιγμα της πόρτας

Συντήρηση και φροντίδα, 28

Αποκλεισμός νερού και ηλεκτρικού ρεύματος

Καθαρισμός της μηχανής

Καθαρισμός του συρταριού απορρυπαντικών

Φροντίδα του κάδου

Καθαρισμός της αντλίας

Έλεγχος του σωλήνα τροφοδοσίας του νερού

Ανωμαλίες και λύσεις, 29-30

Υποστήριξη, 31

ΠΛΥΝΤΗΡΙΟ

AQUALTIS

ADS93D 69

Οδηγίες για την

εγκατάσταση και τη χρήση

! Είναι σημαντικό να διατηρήσετε το εγχειρίδιο αυτό για

να μπορείτε να το συμβουλεύεστε οποιαδήποτε στιγμή.

Σε περίπτωση πώλησης, παραχώρησης ή μετακόμισης,

βεβαιωθείτε ότι παραμένει μαζί με το πλυντήριο.

! Διαβάστε προσεκτικά τις οδηγίες: υπάρχουν σημαντικές

πληροφορίες για την εγκατάσταση, τη χρήση και την

ασφάλεια.

! Στη σακουλίτσα που περιέχει το εγχειρίδιο αυτό θα

βρείτε, εκτός της εγγύησης, υλικά που χρησιμεύουν για

την εγκατάσταση.

Αποσυσκευασία και οριζοντίωση

Αποσυσκευασία

1. Αφού αποσυσκευαστεί το πλυντήριο, ελέγξτε αν έχει

υποστεί ζημιές κατά τη μεταφορά.

Αν έχει υποστεί ζημιές μην το συνδέετε και επικοινωνήστε

με τον μεταπωλητή.

2. Αφαιρέστε τις 4

προστατευτικές βίδες για τη

μεταφορά και τον σχετικό

αποστάτη που βρίσκονται

στο πίσω μέρος (βλέπε

εικόνα).

3. Κλείστε τις οπές με τα πλαστικά πώματα που

περιέχονται στη σακουλίτσα.

4. Φυλάξτε όλα τα κομμάτια. Αν το πλυντήριο χρειαστεί

να μεταφερθεί, θα πρέπει να ξαναμονταριστούν για

την αποφυγή εσωτερικών βλαβών.

! Οι συσκευασίες δεν είναι παιχνίδια για μικρά παιδιά!

Αλφάδιασμα

1. Τοποθετήστε το πλυντήριο σε ένα δάπεδο επίπεδο και

ανθεκτικό, χωρίς να το ακουμπήσετε σε τοίχους ή έπιπλα.

2. Αντισταθμίστε τις

ανωμαλίες ξεβιδώνοντας ή

βιδώνοντας τα ποδαράκια

έως ότου η μηχανή

αλφαδιαστεί (δεν πρέπει να

κλίνει περισσότερο από 2

μοίρες).

! Ένα επιμελές αλφάδιασμα δίνει σταθερότητα και

αποσοβεί δονήσεις και θορυβότητα κυρίως στη φάση

στυψίματος.

! Σε περίπτωση μοκέτας ή τάπητα, ρυθμίστε τα

ποδαράκια έτσι ώστε να υφίσταται κάτω από το

πλυντήριο αρκετός χώρος για τον αερισμό.

Υδραυλικές και ηλεκτρικές συνδέσεις

Σύνδεση του σωλήνα τροφοδοσίας του νερού

! Πριν συνδέσετε το σωλήνα τροφοδοσίας στο δίκτυο

ύδρευσης, αφήστε να τρέξει το νερό μέχρι να βγει

διαυγές.

1. Συνδέστε το σωλήνα

τροφοδοσίας στο

πλυντήριο βιδώνοντάς τον

στην αντίστοιχη είσοδο

νερού, στο πίσω μέρος

επάνω δεξιά (βλέπε

εικόνα).

2. Συνδέστε το σωλήνα

τροφοδοσίας βιδώνοντάς

τον σε ένα κρουνό

κρύου νερού με στόμιο

σπειρώματος 3/4 gas

(βλέπε εικόνα).

3. Προσέξτε ώστε στο σωλήνα να μην υπάρχουν ούτε

πτυχώσεις, ούτε στενώσεις.

! Η πίεση νερού του κρουνού πρέπει να κυμαίνεται

μεταξύ των τιμών του πίνακα Τεχνικά στοιχεία (βλέπε

σελίδα δίπλα).

! Αν το μήκος του σωλήνα τροφοδοσίας δεν επαρκεί,

απευθυνθείτε σε ένα ειδικευμένο κατάστημα ή σε

εξουσιοδοτημένο τεχνικό.

! Μη χρησιμοποιείτε ποτέ χρησιμοποιημένους ή παλιούς

σωλήνες τροφοδοσίας, αλλά εκείνους που παρέχονται με

τη μηχανή.

Εγκατάσταση

Σύνδεση του σωλήνα αποστράγγισης

Συνδέστε το σωλήνα

αδειάσματος σε μια

σωλήνωση αδειάσματος

ή σε μια επιτοίχια

παροχέτευση σε ύψος από

το έδαφος μεταξύ 65 και

100 cm και αποφεύγοντας

ρητά να τον διπλώσετε.

Εναλλακτικά, στηρίξτε το

σωλήνα αδειάσματος στο

χείλος ενός νιπτήρα ή μιας

λεκάνης, δένοντας τον

οδηγό που σας παρέχεται

στον κρουνό (βλέπε

εικόνα).

Το ελεύθερο άκρο του

σωλήνα αδειάσματος

δεν πρέπει να παραμένει

βυθισμένο στο νερό.

! Δεν συνιστάται η χρήση προεκτάσεων σωλήνων. Αν

απαιτείται, η προέκταση πρέπει να έχει την ίδια διάμετρο

του αρχικού σωλήνα και να μην ξεπερνάει τα 150 cm.

Ηλεκτρική σύνδεση

Πριν εισάγετε το βύσμα στην ηλεκτρική πρίζα,

βεβαιωθείτε ότι:

• η πρίζα διαθέτει γείωση και τηρεί τις εκ του νόμου

προδιαγραφές.

• Η πρίζα να είναι σε θέση να υποφέρει το μέγιστο

φορτίο ισχύος της μηχανής, που αναφέρεται στον

πίνακα Τεχνικών στοιχείων (βλέπε δίπλα).

• Η τάση τροφοδοσίας να κυμαίνεται μεταξύ των τιμών

που αναφέρονται στον πίνακα Τεχνικών στοιχείων

(βλέπε δίπλα).

• Η πρίζα να είναι συμβατή με το βύσμα της μηχανής.

Σε αντίθετη περίπτωση, αντικαταστήστε την πρίζα ή το

βύσμα.

! Το πλυντήριο δεν εγκαθίσταται σε ανοιχτό χώρο,

ακόμη και αν ο χώρος είναι καλυμμένος, διότι είναι πολύ

επικίνδυνο να το αφήνετε εκτεθειμένο σε βροχή και

κακοκαιρία.

! Με την εγκατάσταση του πλυντηρίου, η πρίζα ρεύματος

πρέπει να είναι εύκολα προσβάσιμη.

! Μη χρησιμοποιείτε προεκτάσεις και πολύπριζα.

! Το καλώδιο δεν πρέπει να φέρει πτυχές ή να είναι

συμπιεσμένο.

! Το καλώδιο τροφοδοσίας και το βύσμα πρέπει να

αντικαθίστανται μόνο από εξουσιοδοτημένους τεχνικούς.

Προσοχή! Η επιχείρηση αποποιείται κάθε ευθύνης σε

περίπτωση που δεν τηρούνται αυτοί οι κανόνες.

65 - 100 cm

Ôå÷íéêÜ óôïé÷åßá

ÌïíôÝëï ADS93D 69

ÄéáóôÜóåéò

ðëÜôïò cm 59,5

ýøïò cm 85

âÜèïò cm 64,5

×ùñçôéêüôçôá áðü 1 Ýùò 9 kg

ÇëåêôñéêÝò

óõíäÝóåéò

ÂëÝðå ôçí ðéíáêßäá

÷áñáêôçñéóôéêþí åðß ôçò ìç÷áíÞò

ÓõíäÝóåéò íåñïý

ìÝãéóôç ðßåóç 1 MPa (10 bar)

ÅëÜ÷éóôç ðßåóç 0,05 MPa (0,5 bar)

÷ùñçôéêüôçôá ôïõ êÜäïõ 62 ëßôñá

Ôá÷ýôçôá

óôõøßìáôïò

ìÝ÷ñé 1600 óôñïöÝò ôï ëåðôü

Προγράμματα

ελέγχου σύμφωνα

με τις οδηγίες

1061/2010 και

1015/2010.

ðñüãñáììá

; èåñìïêñáóßá 60°C;

ðñüãñáììá

; èåñìïêñáóßá 40°C.

Ç óõóêåõÞ áõôÞ åßíáé óýìöùíç ìå

ôéò áêüëïõèåò ÊïéíïôéêÝò Ïäçãßåò:

- 2004/108/CE

(ÇëåêôñïìáãíçôéêÞ Óõìâáôüôçôá)

- 2002/96/CE

- 2006/95/CE (×áìçëÞ ÔÜóç)

Περιγραφή της μηχανής

ΠΟΡΤΑ

Για να ανοίξετε την πόρτα

χρησιμοποιείτε πάντα

τη σχετική λαβή (βλέπε

εικόνα).

Θήκη απορρυπαντικώí

Βρίσκεται στο εσωτερικό

της μηχανής και έχετε

πρόσβαση ανοίγοντας την

πόρτα.

Για τη χρήση βλέπε το

κεφάλαιο “Auto Dose Sy-

stem”.

ΠΊΝΑΚΑΣ ΧΕΙΡΙΣΤΗΡΊΩΝ TOUCH CONTROL

Για να αλλάξετε τις ρυθμίσεις

πιέστε ελαφρά στο

εικονίδιο στο εσωτερικό της

ευαίσθητης περιοχής (touch

control) όπως υποδεικνύεται

στην εικόνα.

Τρόπος stand by

Το πλυντήριο αυτό, σύμφωνα με τις νέες ρυθμίσεις

σχετικές με την εξοικονόμηση ενέργειας, διαθέτει

ένα σύστημα αυτόματου σβησίματος (stand by) που

τίθεται σε λειτουργία μετά από περίπου 30 λεπτά στην

περίπτωση μη χρήσης. Πατήστε σύντομα το κουμπί

ON-OFF και περιμένετε η μηχανή να ενεργοποιηθεί εκ

νέου.

Κατανάλωση σε off-mode: 1 W

Κατανάλωση σε Left-on: 1 W

ΠΊΝΑΚΑΣ ΧΕΙΡΙΣΤΗΡΊΩΝ

TOUCH CONTROL

ΠΟΡΤΑ

ΛΑΒΗ

ΠΟΡΤΑΣ

ΡΥΘΜΙΖΌΜΕΝΑ ΠΟΔΑΡΆΚΙΑ

ΒΑΣΗ

Sayfa yükleniyor ...

Whirlpool ADS93D 69 EU/B Kullanici rehberi

Marka: Whirlpool

Model: ADS93D 69 EU/B

Kategori: Çamaşır makineleri

Tip: Kullanici rehberi

PDF İndir

rapor

Whirlpool ADS93D 69 EU/B Kullanici rehberi

Whirlpool ADS93D 69 EU/B Kullanici rehberi

İlgili Makaleler

Diğer Belgeler