Indesit L 60 T3C TK Kullanici rehberi

Marka: Indesit

Modeli: L 60 T3C TK

Kategori: Bulaşık makineleri

Tip: Kullanici rehberi

DISHWASHER

Contents

Installation, 2-3

Positioning and levelling

Connecting the water and electricity supplies

Technical data

Description of the appliance, 4

Overall view

Control panel

Loading the racks, 5

Lower rack

Cutlery basket

Upper rack

Start-up and use, 6

Starting the dishwasher

Loading the detergent

Washing options

Wash cycles, 7

Wash cycle table

Rinse aid and refined salt, 8

Loading the rinse aid

Loading the refined salt

Care and maintenance, 9

Shutting off the water and electricity supplies

Cleaning the dishwasher

Preventing unpleasant odours

Cleaning the sprayer arms

Cleaning the filters

Leaving the machine unused for extended periods

Precautions and advice, 10

General safety

Disposal

Saving energy and respecting the environment

Troubleshooting, 11

Assistance, 12

Before calling for Assistance

English, 1

Instruction booklet

L 60 T 3 C

T R

Türkçe, 13

 Keep this instruction manual in a safe place for

future reference. If the appliance is sold, given away

or moved, please ensure the manual is kept with the

machine, so that the new owner may benefit from the

advice contained within it.

 Please read this instruction manual carefully: it

contains important information regarding the safe

installation, use and maintenance of the appliance.

 If the appliance must be moved at any time, keep

it in an upright position; if absolutely necessary, it

may be tilted onto its back.

Positioning and levelling

1. Remove the appliance from all packaging and

check that it has not been damaged during

transportation.

If it has been damaged, contact the retailer and do

not proceed any further with the installation process.

2. Check the dishwasher by placing it so that its

sides or back panel are in contact with the adjacent

cabinets or even with the wall. This appliance can

also be recessed under a single worktop* (

see the

Assembly instruction sheet

3. Position the dishwasher on a level and sturdy floor.

If the floor is uneven, the front feet of the appliance

may be adjusted until it reaches a horizontal position

(the angle of inclination must not exceed 2 degrees).

If the appliance is levelled correctly, it will be more

stable and much less likely to move or cause

vibrations and noise while it is operating.

Connecting the water and electricity

supplies

 Connection to the water and electricity supplies

should only be performed by a qualified technician.

 The dishwasher should not stand on top of the

water hoses or the electricity supply cable.

The water inlet (A) and outlet (B) hoses and the

electricity supply cable may be positioned towards

the right or the left in order to achieve the best

possible installation (

see figure

Connecting the water inlet hose

• To a suitable cold water connection point: before

attaching the hose, run the water until it is

perfectly clear so that any impurities that may be

present in the water do not clog the appliance;

after performing this operation, screw the inlet

hose tightly onto a tap with a ¾ gas threaded

connection.

• To a suitable hot water connection point: your

dishwasher may be provided with hot water from

the mains supply (if you have a central heating

system with radiators) provided that it does not

exceed a temperature of 60°C.

Screw the hose to the tap as described for

connection to a cold water supply.

 If the inlet hose is not long enough, contact a

specialist store or an authorised technician (

see

Assistance

 The water pressure must be within the values

indicated in the Technical data table (

see below

 The hose should not be bent or compressed.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the

water supply in the event of anomalies or leaks from

inside the appliance.

- is provided with a

Water Stop

* safety device, in

other words it has a water inlet hose that consists of

a transparent hose on the outside and a red hose on

the inside: both the hoses can withstand extremely

high pressure. If the internal hose breaks, the

external hose becomes a bright red colour and

carries the water instead, thus avoiding any leakage.

 It is very important to check the external hose

regularly: if it is a bright red colour, it must be

replaced by an authorised technician as soon as

possible (

see Assistance

Installation

Connecting the water outlet hose

Connect the outlet hose (without bending it) to a

drain duct with a minimum diameter of 4 cm.

Alternatively, rest it over a sink or tub; the free end

of the hose should not remain immersed in water.

The special plastic

elbow* makes it easier to

find the best layout: fix

the elbow to the wall

securely in order to

prevent the outlet hose

from moving and spilling

the dirty water.

The part of the hose

marked with the letter A

should be between 40 and 100 cm above the ground

(

see figure

 We advise against the use of hose extensions.

Electrical connection

Before inserting the plug into the electrical socket,

make sure that:

• the socket is earthed and complies with current

regulations;

• the socket can withstand the maximum load of

the appliance, which is indicated on the data

plate located on the inside of the door (

see

Description of the appliance

);

• the power supply voltage falls within the values

indicated on the data plate on the inside of the

door;

• the socket is compatible with the plug of the

appliance. If this is not the case, ask an

authorised technician to replace the plug (

see

Assistance

); do not use extension cables or

multiple sockets.

 Once the appliance has been installed, the power

supply cable and the electrical socket should be

easily accessible.

 The cable should not be bent or compressed.

 The cable should be checked regularly and

replaced by authorised technicians only (

see

Assistance

 The Company shall not be held responsible for any

incidents that occur if these regulations are not

observed.

Advice regarding the first wash cycle

After the appliance has been installed, immediately

before running the first wash cycle, completely fill

the salt dispenser with water and add approximately

2 kg of salt (

see Rinse aid and refined salt

). The

water may overflow: this is normal and is not a

cause for concern. It is also normal that the LOW

SALT* indicator light continues to flash for a few

cycles after the salt has been loaded.

* Only available in selected models.

Technical data

Dimensions

width 60 cm

height 85 cm

depth 60 cm

Capacity

12 standard place-settings

Water supply

pressure

30 Kpa ÷ 1Mpa (0.3 ÷ 10 bar)

4.3 psi – 145 psi

Power supply

voltage

See appliance data plate

Total absorbed

power

See appliance data plate

Fuse

See appliance data plate

This dishwasher conforms to

the following European

Community Directives:

-73/23/EEC dated 19/02/73

(Low Voltage) and subsequent

modifications

-89/336/EEC dated 03/05/89

(Electromagnetic Compatibility)

and subsequent modifications

-97/17/EC (Labelling)

-2002/96/ CE

Waste

Electrical and Electronic

Equipment (WEEE)

Overall view

1. Upper rack

2. Upper sprayer arm

3. Tip-up compartments

4. Rack height adjuster

5. Lower rack

6. Lower sprayer arm

7. Cutlery basket

8. Washing filter

9. Salt dispenser

10. Detergent and rinse aid dispensers

11. Data plate

* Only available in selected models.

Description of the appliance

Control panel

WASH CYCLE

SELECT

knob

LOW SALT

indicator light*

WASH CYCLE PHASE

indicator lights

PRE-WASH

WASH

DRYING

RINSE

ON-OFF

button

ON-OFF

indicator light

If the rack is equipped with the click

clack handles* (

see figure

), pull

them upwards or downwards to

adjust the height.

Loading examples for the upper rack

Loading examples for the lower rack

Baby Tip-up compartments

For dishwasher models with a

Baby Cycle, tip-up

compartments suitable for

washing bottles, rings and

teats are provided.

Items that should not be washed in the dishwasher

• Wooden items, objects with wooden or horn

handles or glued-on parts.

• Items made from aluminium, copper, brass,

pewter or tin.

• Items made from plastic that is not heat-

resistant.

• Antique or hand-painted porcelain.

• Antique silver. Silver that is not antique may,

however, be washed in the dishwasher using a

delicate wash cycle, provided that it does not

come into contact with other metals.

 When buying crockery and cutlery we recommend that you

check whether it can be washed using the dishwasher.

Washing the handles*

To wash the upper and lower rack handles: remove the two

fastening plugs, lift out the handles and rinse them under

running water, then fasten them to the rack using the same

plugs.

* Only available in selected models.

** The number and position may vary.

 Before loading the rack, remove all food residue from the

crockery, leave saucepans and frying pans with burnt-on

residue to soak

in water only and empty all remaining liquid

from cups and glasses. After loading the appliance, check

that the sprayer arms can rotate freely.

Lower rack

Arrange the more difficult items to wash using the

examples

as a guide and use the collapsible supports* where

needed.

• Serving dishes and lids: place these at the sides

of the rack.

• Saucepans and salad bowls: always turn these

upside down.

• Very deep dishes: position these at an angle.

In order to guarantee the best washing and drying

performance, the surface of the lower rack is more uneven

than that of the upper rack.

Cutlery basket

The type of cutlery basket may vary according to the

dishwasher model.

 Knives and other sharp utensils should be placed in the

cutlery basket with the point facing downwards.

To divide the central basket* into two separate pieces: pull out

the handle. The two detachable side compartments* may be

hooked onto the upper or lower rack.

The two grids* may be positioned in the basket to separate

the cutlery: place the pieces of cutlery into the appropriate

compartments with the handles at the bottom.

Upper rack

Load this rack with delicate and lightweight crockery: glasses,

tea and coffee cups, saucers, small salad bowls, saucepans

and small saucepans that are not too soiled, using the

examples

as a guide.

• Lightweight crockery: position these dishes so

that they will not be moved by the jets of water.

• Mugs and cups: place these on the tip-up

compartments**.

• Long sharp knives and serving utensils: place

these on the tip-up compartments**.

Adjusting the height of the upper rack

In order to make it easier to arrange

the crockery, the upper rack may be

moved to a higher or lower level.

Open the left and right guide rail

stops and pull out the rack; position

it higher or lower as required, slide it

along the guide rails until the front

wheels are in place and close the

stops (

see figure

Loading the racks

Starting the dishwasher

1. Turn the water tap on.

2. Press the ON/OFF button: the indicator light will

illuminate.

3. Open the door and pour in a suitable amount of

detergent (

see below

4. Load the racks (

see Loading the racks

) and shut

the door.

5. Select the desired wash cycle depending on the

dishes and how dirty they are (

see table of wash

cycles

), by turning the knob clockwise.

6. Select the wash options (

see below

Only

available in selected models).

7. After a few minutes the cycle start and the WASH

CYCLE PHASE indicator lights display the status

of the cycle:

Pre-wash, Wash, Rinse, Drying.

8. At the end of the cycle the DRYING indicator

light will flash.

9. Turn the knob anti-clokwise to RESET in order to

reset all the settings.

10.Switch off the appliance by pressing the ON/OFF

button, shut off the water tap and unplug the

appliance from the electricity socket.

11.Open the door and wait for a few minutes before

removing the crockery, in order to avoid burns.

Unload the racks, beginning with the lower level.

Modifying the duration of a wash cycle already in

progress

If a mistake was made during the wash cycle

selection process it is possible to change the cycle,

provided that it has only just begun: turn the knob

anti-clockwise until it reaches the RESET position.

After a few seconds the WASH CYCLE PHASE

indicator light will switch off: select the new cycle.

Adding extra crockery

Press the ON/OFF button and open the door, taking

care to avoid the escaping steam, and place the

crockery inside the dishwasher. Press the ON/OFF

button again: the cycle starts from the point at which

it was interrupted.

Accidental interruptions

If the door is opened during the wash cycle, or if

there is a power cut, the cycle stops. It starts again

from the point at which it was interrupted once the

door has been shut or the electricity supply is

restored.

Loading the detergent

A successful wash also depends on the correct

amount of detergent being used, as recommended

by the manufacturer. Exceeding the recommended

amount does not result in a more effective wash and

pollutes the environment.



To obtain the best results from each washing and

drying cycle, powder detergent, rinse aid liquid and

salt should be used.

comparcompar

compar

tment Atment A

tment A: Washing detergent

comparcompar

compar

tment Btment B

tment B: Pre-wash detergent

1. Open cover C by

pressing button D.

2. Pour in the detergent

after consulting the

Wash

cycle table

• for powder detergent

use compartments A and

• for tablets, use

compartment A and the

bottom of the appliance,

i.e. when the cycle

requires 1 tablet, place it in compartment A and

close the cover; when it requires 2, place the second

tablet at the bottom of the appliance.

3. Remove detergent residues from the edges of the

compartment and close the cover until it clicks.

Start-up and use

* Only available in selected models.

Wash cycle table

Note

To make it easier to measure out the detergent, it is worth remembering that:

1 tablespoon = 15 grams of powder = approximately 15 ml of liquid

1 teaspoon = 5 grams of powder = approximately 5 ml of liquid

 Ariston dishwashers are fitted with an automatic filter cleaning system that may increase the cycle duration.

Wash cycles

 The number and type of wash cycles varies according to the model of dishwasher.

 If the crockery is only lightly soiled or if it has been rinsed with water before being placed in the dishwasher,

reduce the amount of detergent used accordingly.

Detergent

(A) = compartment A

(B) = compartment B

Wash cycle

selection

instructions

Wash cycle

Powder Liquid Tablets

Pre-wash Drying

Wash cycle

duration

(tolerance

±10%)

Extremely soiled

dishes and pans (not

to be used for

delicate items).

Intensive

30 g (A)

5 g (B)

30 ml (A)

5 ml (B)

1 (A)

1 (bottom of

the

appliance)

•

2:00’

Normally soiled pans

and dishes.

Standard daily wash

cycle.

Normal

30 g (A) 30 ml (A) 1 (A)

•

1:12’

Environmentally-

friendly wash cycle

with low energy

consumption levels,

suitable for pans and

dishes.

Eco

25 g (A)

5 g (B)

25 ml (A)

5 ml (B)

1 (A)

•

2:10’

 Only use products that have been specifically

designed for dishwashers.

Do not use table salt or industrial salt.

 If using a multi-functional product (2-in-1, 3-in-1, 4-in-

1,etc.) it is not necessary to add rinse aid; however,

we recommend that you add salt, especially if you

live in an area where the water is hard or very hard. If

you do not add salt or rinse aid, the LOW SALT* and

LOW RINSE AID* indicator lights will flash

continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry, as

water runs off surfaces more readily and therefore

does not leave streaks or marks.

The rinse aid dispenser should be filled:

• whenever the indicator light (H) signals that it is

empty. Illuminated light: add rinse aid; unlit light:

there is no shortage of rinse aid in the dispenser.

• when the LOW RINSE AID* indicator light on the

panel flashes;

1. Open the dispenser by

turning the lid (G) in an

anticlockwise direction.

2. Pour in the rinse aid,

making sure it does not

overflow from the

dispenser. If this happens,

clean the spill immediately

with a sponge.

3. Screw the lid back on.

NEVER pour the rinse aid directly into the appliance

tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the washing

or drying results, you may adjust the quantity of

rinse aid used. Use a screwdriver to turn the dosage

adjuster to one of the 6 pre-set positions (the default

position is set to 4):

• if there are bluish streaks on the crockery, set the

adjuster to a lower number (1-3).

• if drops of water remain on the crockery or there

are limescale marks present after the cycle has

finished, set the adjuster to a higher number (4-6).

 If you are using multi-functional tablets (2-in-1, 3-in-1,

4-in-1, etc.) and you wish to further improve the

drying performance of the appliance, fill the

dispenser and set the dosage adjuster to 2.

Loading the refined salt

In order to obtain the best possible results from a

wash cycle, make sure that the dispenser is never

empty. Refined salt removes limescale from the

water, thus avoiding the formation of deposits on

crockery. The salt dispenser is located in the lower

part of the dishwasher (

see Description

) and should

be filled:

• when the green float* cannot be seen by simply

looking at the cap of the salt dispenser;

• when the LOW SALT* indicator light on the panel

flashes;

• if your machine is not equipped with an indicator

light or a green float:

approximately every 30 wash cycles;

1. Remove the lower rack and

unscrew the cap of the

dispenser (in an anti-

clockwise direction).

2. For the first wash cycle

only: fill the dispenser up to

the edges with water.

3. Position the funnel provided

correctly (

see figure

) and fill the salt dispenser up to

the edges (approximately 2 kg); it is normal for a

little water to leak out.

4. Remove the funnel, wipe away any salt residue

from the thread and screw the cap on tightly, so that

detergent does not leak into the dispenser during

the wash cycle (this could damage the water

softening system beyond repair).

 When salt has been added, run a wash cycle

immediately, without crockery, in order to remove

any salt solution that has leaked out and to avoid

corrosion.

Adjusting the amount of salt*

It is possible to adjust the amount of salt used

according to the hardness of the water in your area

(this information is available from your local water

board).

1. Unscrew the dispenser cap.

2. Turn the arrow on the neck of the

dispenser (

see figure

) towards the

+ or - symbols, using the table

below as a guide.

The default setting of the water softening system is +.

- If using multi-functional tablets (2-in-1, 3-in-1, 4-in-

1,etc.) fill the salt dispenser and set the adjuster to -; if

the hardness of the water is greater than 60°fH, set it

to +.

* Only available in selected models.

Rinse aid and refined salt

Shutting off the water and electricity

supplies

• Turn off the water tap after every wash cycle to

avoid leaks.

• Remove the plug from the socket when cleaning

the machine and when carrying out maintenance

work.

Cleaning the dishwasher

• The external surfaces of the machine and the

control panel may be cleaned using a non-

abrasive cloth which has been dampened with

water. Do not use solvents or abrasive products.

• Any marks on the appliance interior may be

removed using a cloth dampened with water and

a little vinegar.

Preventing unpleasant odours

• Always keep the door of the appliance ajar in

order to avoid moisture from forming and being

trapped inside the machine.

• Clean the seals around the door and detergent

dispensers regularly using a damp sponge. This

will avoid food becoming trapped in the seals,

which is the main cause of the formation of

unpleasant odours.

Cleaning the sprayer arms

Food residue may

become encrusted onto

the sprayer arms and

block the holes used to

spray the water. It is

therefore recommended

that the arms are

checked from time to

time and cleaned with a

small non-metallic

brush.

Cleaning the filters

The filters remove food residue from the water used

in the wash cycle: to obtain the best results from

each wash, they should be cleaned.

 Clean the filters regularly.

 After cleaning check that the filter assembly has

been replaced correctly.

 The dishwasher should not be used without filters

or when the filter is loose.

1. Remove the filters by pulling the handle upwards.

2. Clean the filters:

• after every wash

cycle, remove the

largest pieces of

residue from

semicircular plate A

and glass B (these

may be removed by

pulling the handle) by

rinsing them under

running water.

• The entire filter

assembly should be

cleaned thoroughly

once a month: this

includes the

semicircular plate A,

the glass B and the

cylinder C (this may be

removed by turning it in

an anti-clockwise

direction). Use a small

non-metallic brush to clean these parts.

3. Reconstruct the filter assembly and replace it in

the correct position, following movements 1 and 2 as

shown in the figure, until it clicks into place.

Leaving the machine unused for

extended periods

• Run a wash cycle when the dishwasher is empty.

• Unplug the appliance and disconnect the water

supply.

• Leave the door of the appliance ajar.

Care and maintenance

 The appliance was designed and manufactured in

compliance with current international safety

standards. The following information has been

provided for safety reasons and should therefore be

read carefully.

General safety

• The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

• The appliance must be used by adults only, to

wash domestic crockery according to the

instructions in this manual.

• The appliance must not be installed outdoors,

even in covered areas. It is extremely dangerous

to leave the machine exposed to rain and storms.

• Do not touch the appliance when barefoot.

• When unplugging the appliance always pull the

plug from the mains socket, do not pull on the

cable.

• The water supply tap must be shut off and the

plug should be removed from the electrical

socket before cleaning the appliance or carrying

out any maintenance work.

• If the appliance breaks down, do not under any

circumstances touch the internal parts in an

attempt to carry out the repair work yourself.

• Never touch the heating element.

• Do not lean or sit on the open door of the

appliance: this may cause the appliance to

overturn.

• Keep detergent and rinse aid out of reach of

children.

• The packaging material should not be used as a

toy: it can become a choking or suffocation

hazard.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE),

requires that old household electrical appliances

must not be disposed of in the normal unsorted

municipal waste stream. Old appliances must be

collected separately in order to optimise the

recovery and recycling of the materials they contain

and reduce the impact on human health and the

environment. The crossed out "wheeled bin" symbol

on the product reminds you of your obligation, that

when you dispose of the appliance it must be

separately collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Saving energy and respecting the

environment

Saving water and energy

• Only start a wash cycle when the dishwasher is

full. While waiting for the dishwasher to be filled,

prevent unpleasant odours with the Soak cycle

(

see Wash Cycles

• Select a wash cycle that is suited to the type of

crockery and to the soil level of the crockery

using the

Wash cycle table

- for dishes with a normal soil level, use the Eco

wash cycle, which guarantees low energy and

water consumption levels.

- if the load is smaller than usual activate the Half

load option (

see Start-up and use

• If your electricity supply contract gives details of

electricity saving time bands, run wash cycles

during the periods when a lower tariff is applied.

The Delayed start* button (

see Start-up and use

)

helps you organise the wash cycles accordingly.

Phosphate-free and chlorine-free detergents

containing enzymes

• We strongly recommend that you use detergents

that do not contain phosphates or chlorine, as

these products are harmful to the environment.

• Enzymes provide a particularly effective action at

temperatures around 50°C, and as a result

detergents containing enzymes can be used in

conjunction with low-temperature wash cycles in

order to achieve the same results as a normal

65°C wash cycle.

• To avoid wasting detergent, use the product in

appropriate quantities based on the

manufacturer’s recommendations, the hardness

of the water and the soil level and quantity of the

crockery. Even if they are biodegradable,

detergents contain substances that may alter the

balance of nature.

* Only available in selected models.

Precautions and advice

Whenever the appliance fails to work, check for a solution from the following list before calling for Technical

Assistance Centre.

Troubleshooting

Malfunction: Possible causes / Solutions:

The dishwasher does not start.

 The plug has not been inserted into the electrical socket

properly, or there is no power in the house.

 The dishwasher door has not been shut properly.

 A delayed start has been programmed (see Start-up and use).

No water enters the dishwasher.

 There is no water in the mains supply.

 The water inlet hose is bent (see Installation).

No water drains out from the

dishwasher.

 The dishwasher cycle has not yet finished.

 The water outlet hose is bent (see Installation).

 The drain duct is blocked.

 The filter is clogged up with food residues.

The dishwasher makes

excessive noise.

 The dishes are rattling against each other or against the

sprayer arms.

The dishes and glasses are

covered in a white film or

limescale deposits.

 The level of the refined salt is low or the dosage setting is not

suited to the hardness of the water (see Rinse aid and salt).

 The lid on the salt dispenser is not closed properly.

 The rinse aid has been used up or the dosage is too low.

 The crockery is made from non-stick material.

The dishes and glasses are

streaked or have a bluish

tinge.

 The rinse aid dosage is too high.

The crockery has not been dried

properly.

 The rinse aid has been used up or the dosage is too low (see

Rinse aid and salt).

 The rinse aid dispenser setting is not high enough.

 A wash cycle without a drying programme has been selected.

The dishes are not clean.

 The racks are overloaded (see Loading the racks).

 The crockery has not been arranged well.

 The sprayer arms cannot move freely.

 The wash cycle is too gentle (see Wash cycles).

 The detergent has not been measured out correctly or it is not

suited to the type of wash cycle (see Start-up and use).

 The filter is dirty or blocked (see Care and maintenance).

 The refined salt level is low (see Rinse aid and salt).

Tap shut-off alarm.

(several short beeps are emitted)

* Only available in selected models.

(the second and third WASH

CYCLE PHASE indicator lights

flash, beginning from the right).

 Turn on the tap and the appliance will start after a few

minutes.

 The appliance lock has been activated because no action was

taken when the beeps* sounded. Switch off the machine using

the ON/OFF button, turn on the tap and switch the machine

back on after 20 seconds by pressing the same button. Re-

programme the machine and restart the wash cycle.

Clogged filter alarm

(the second and fourth WASH

CYCLE PHASE indicator lights

flash, beginning from the right).

 Switch off the machine by pressing the ON/OFF button and

clean the filters (see Maintenance), then switch the

dishwasher back on by pressing the same button. Re-

programme the machine and restart the wash cycle.

Water loading solenoid

valve malfunction alarm

(the third WASH CYCLE PHASE

indicator light flashes, beginning

from the right).

 Switch off the appliance by pressing the ON/OFF button and

switch it back on after a minute. If the alarm continues, shut

off the water tap to eliminate the risk of flooding, remove the

plug from the electrical socket and call Assistance.

Assistance

Before calling for Assistance:

• Check whether you can solve the problem on

your own (

see Troubleshooting

);

• Restart the programme to check whether the

problem has been solved;

• If this is not the case, contact an authorised

Technical Assistance Centre on the telephone

number provided on the guarantee certificate.

 Always request the assistance of authorised

servicemen.

Notify the operator of:

• the type of problem.

• the appliance model (Mod.).

• the serial number (S/N).

This information can be found on the data plate

situated on the internal edge of the stainless steel

door (see Description of the appliance).

BULAÞIK MAKÝNESÝ

L 60 T 3C

Türkçe, 13

Kullaným kýlavuzu

Içindekiler

Montaj, 14-15

Yerleþtirme ve seviye ayarlama

Elektrik ve su baðlantýlarý

Teknik veriler

Cihazýn tanýtýmý, 16

Genel görünüm

Kontrol paneli

Sepetlerin doldurulmasý, 17

Alt sepet

Çatal Kaþýk Sepeti

Üst sepet

Çalýþtýrma ve kullanma, 18

Bulaþýk makinesinin çalýþtýrýlmasý

Deterjan doldurulmasý

Yýkama seçenekleri*

Programlar, 19

Program çizelgesi

Parlatýcý ve yenileyici tuz, 20

Parlatýcý doldurulmasý

Yenileyici tuz doldurulmasý

Bakým ve temizlik, 21

Elektrik þebekesinin ve su tesisatýnýn devre

dýþý býrakýlmasý

Bulaþýk makinesinin temizlenmesi

Ýstenmeyen kokularýn önlenmesi

Püskürtme kollarýnýn temizlenmesi

Filtrelerin temizlenmesi

Makinenin uzun süre kullanýlmamasý

Önlemler ve öneriler, 22

Genel güvenlik uyarýlarý

Tasarruf ve çevreye saygý

Ariza ve onarým, 23

Teknik Servis, 24

Servis aramadan önce

 Bu kitapçýðý gerektiði her an danýþabilmeniz için

özenle saklayýnýz. Satýþ, devir yada taþýnma

halinde, çalýþma sistemi ve bununla ilgili uyarýlar

konusunda yeni sahibinin bilgilenmesi için bu

kitapçýðýn cihazla birlikte kalmasýný saðlayýnýz.

 Talimatlarý dikkatlice okuyunuz: montaj, kullaným

ve güvenliðe iliþkin önemli bilgiler içermektedir.

 Taþýma halinde cihazýn dik tutulmasý, ya da

gerekli olduðu takdirde arka tarafa doðru

yatýrýlmasý gerekmektedir.

Yerleþtirme ve seviye ayarlama

1. Cýhazýn ambalajýný çýkarýn ve cihazda nakliyat

sýrasýnda hasar meydana gelip gelmediðini kontrol

edin.

Hasarlý ise, cihazý baðlamadan hemen Teknik

Servise baþvurunuz.

2. Makinenin arka tarafý yada yanlarý duvara yada

yanýndaki mobilyalara dayanacak þekilde

yerleþtiriniz. Cihaz mutfak tezgahýnýn altýna

ankastre edilebilir (Montaj bölümüne bakýnýz* ).

3. Bulaþýk makinesini düz ve sert bir zemine

yerleþtiriniz. Ayarlanabilir ayaklarý gevþeterek ya

da sýkarak cihazýn zemine tamamen oturmasýný

saðlayýnýz (en fazla 2 derece eðilebilir). Cihazýn

seviyesinin dikkatlice ayarlanmasý makinenin

titremesini, ses çýkarmasýný ve yerinden

oynamasýný engeller.

Elektrik ve su baðlantýlarý

 Bu cihazýn montajý sýrasýnda her tür elektrik ve su

baðlantý iþleminin sadece vasýflý personel

tarafýndan yapýlmasý gerekir.

 Bulaþýk makinesi elektrik kablolarý veya borularý

üzerine yerleþtirimemelidir.

Montajý kolaylaþtýrmak için, su besleme hortumu

(A), atýk su boþaltma hortumu (B) ve elektrik

besleme kablosu saða veya sola döndürülebilir

(aþaðdaki þekile bakýnýz ).

Su besleme hortumunun baðlantýsý

 Soðuk su giriþine baðlanmasý: Su besleme

hortumunu 3/4 inç yivli musluða iyice

baðlayýnýz. Hortumu musluða vidalamadan önce

suyun içindeki atýklarýn muluðu týkamamasý için

suyu temiz oluncaya kadar akýtmanýz gerekir.

 Sýcak su giriþine baðlanmasý: merkezi ýsýtma

sistemi söz konusu ise; bulaþýk makinesi sýcak

suya baðlý olarak çalýþabilir, ancak suyun

sýcaklýðý 60°Cyi geçmemelidir.

Hortumu, soðuk su giriþine baðlanmasý

bölümünde açýklandýðý gibi musluða

vidalayýnýz.

 Su besleme hortumunun uzunluðu montaj için

yeterli deðilse yetkili bir maðazaya ya da

teknisiyene baþvurmanýz gerekir (Teknik Servise

bakýnýz) .

 Suyun basýncý Teknik Veriler kýsmýnda belirtilen

sýnýr kapsamýnda olmalýdýr. (aþaðýya bakýnýz).

 Hortum kývrýlmamalý, bükülmemeli veya

sýkýþmamalýdýr.

Su kaçaklarýna karþý emniyet sistemi

Bulaþýk makinesi, su basmasýný önlemek için

- herhangi bir ariza ya da su kaybý olmasý

durumunda su giriþini durdurma sistemine sahiptir.

- ayrýca Water Stop* emniyetine sahiptir, yani su

besleme hortumu iki hortum cidarýndan oluþur; dýþ

hortum þeffaf, iç hortum ise kýrmýzýdýr, hortumun

ikisi de yüksek basýnca dayanýklýdýr. Ýç hortum

hasar gördüðünde dýþ hortum canlý kýrmýzý

renklenir ve suyu onun içine akýtýr. Böylece kaçak

engellenir.

 Dýþ hortumun periyodik olarak kontrol edilmesi

çok önemlidir: kýrmýzý renklendiði takdirde en yakýn

zamanda yetkili Teknik Servis tarafýndan hortumun

deðiþtirlimesi gerekir (Teknik Servis bölümüne

bakýnýz).

* Sadece bazý modellerde mevcuttur.

148

12083

121168

100

Montaj

Atýk su boþaltma hortumunun baðlantýsý

Atýk su boþaltma hortumunu, kývýrmadan iç çapý en

az 4 cm olan bir boþaltma kanalýna baðlayýnýz veya

bir küvvetin ya da lavabonun kenarýna yatýrýn. Atýk

su boþaltma hortumunun ucu suyun içinde

olmamalýdýr.

Özel kavisli plastik

kýlavuz* kullanýlarak

hortumun

yerleþtirilmesi

kolaylaþir: özel kavisli

plastik kýlavuzu duvara

sabitleyiniz: böylece

hortumun yerinden

oynamasý ve

dolayýsýyla suyu dýþarý

akýtamasý engellenir.

Hortumun A harfiyle belirtilen kýsmý 40 cm ile - 100

cm arasýndaki bir yükseklikte olmalýdýr (þekile

bakýnýz).

 Uzatma hortumlarýnýn kullanýlmamasý tavsiye

edilir.

Elektirik baðlantýsý.

Cihazýn fiþini bir elektrik prizine takmadan önce

aþaðýdaki noktalarý kontrol edin:

 priz topraklý tesisata sahip ve yürürlükteki

normlara uygun olmalýdýr;

 elektrik prizi özellik etikentinde belirtilen

maksimum yükü taþýyabilmelidir (Cihazýn tanýmý

bölümüne bakýnýz );

 besleme gerilimi özellik plakasýnda belirtilen

deðer sýnýrý kapsamýnda olmalýdýr;

 priz ve fiþ birbiriyle uyumlu olmalýdýr. Aksi

takdirde cihazýn fiþinin deðiþtirilmesi için yetkili

Servise (Teknik Servis bölümüne bakýnýz)

baþvurmanýz gerekir, uzatma kablosu ya da

çoklu priz kullanmayýnýz.

 Cihaz monte edildikten sonra besleme kablosuna

ve elektrik prizine kolayca ulaþýlabilmelidir.

 Kablo kývrýlmamalý ve sýkýþtýrýlmamalýdýr.

 Kablonun periyodik olarak kontrol edilmesi ve

sadece yetkili personel tafarýndan deðiþtirilmesi

gerekir (Teknik Servis bölümüne bakýnýz).

 Üretici firma yukarýdaki normlarýn dikkate

alýnmamasý durumunda hiçbir sorumluluk kabul

etmeyecektir.

Ýlk kullaným uyarýlarý

Bulaþýk makinesi monte edildikten sonra, ilk kez

kullanýlmadan önce tuz haznesini su ile doldurun

ve yaklaþýk 2 Kg. tuz ilave edin (Parlatýcý ve

yenileyici tuz bölümüne bakýnýz): suyun akmasý

normaldýr. Tuz doldurulduktan sonra da TUZ

EKSÝKLÝÐÝ* uyarý lambasýnýn birkaç devir için

yanýp sönmesi normaldýr.

* Sadece bazý modellerde mevcuttur.

Teknik veriler

Boyutlar

geniºlik cm 60

yükseklik cm 85

derinlik cm 60

Kapasite

12 yer ayarý

ªebeke suyu

basýncý

30 Kpa ÷ Mpa (0,3 ÷ 10 bar)

4,3 psi – 145 psi

Besleme gerilimi

Özellikler etiketine bak

Toplam güç:

Özellikler etiketine bak

Sigorta

Özellikler etiketine bak

Bu cihaz aþaðýdaki AB

Yönergeleri ile uyumludur:

19/02/73 tarihli EAT 73/23

(Düºük Voltaj Yönergesi) ve

sonraki deðiþiklikler;

03/05/89 tarihli EAT 89/336

(Elektromanyetik Uyum

Yönergesi) ve sonraki

deðiþiklikler;

- 97/17/AT (etiket ket Yönergesi)

- 2002/96/CE

Genel görünüm

1. Üst sepet

2. Üst püskürtme kolu

3. Raflar

4. Sepet yükseklik ayarý

5. Alt sepet

6. Alt püskürtme kolu

7. Çatal kaþýk sepeti

8. Yýkama filtresi

9. Tuz haznesi

10. Deterjan kutusu ve parlatýcý haznesi

11. Özellikler plakasý

* Sadece bazý modellerde mevcuttur.

Kontrol paneli

Cihazýn tanýtýmý

ON/OFF

Düðmesi

ON/OFF

Uyarý lambasý

Program

seçme

düðmesi

TUZ EKSÝKLÝÐÝ

Uyarý lambasý*

PROGRAM TAKÝP

uyarý lambasý

ÖN YIKAMA

YIKAMA

DURULAMA

KURUTMA

Sepet click clack* kulplu ise(þekile

bakýnýz), aþaðýya ya da yukarýya

doðru çekilerek sepetin yüksekliði

ayarlanabilir.

Üst sepet yerleþtirme örneði

Alt sepet yerleþtirme örneði

Bebek raflarý**

Bebek yýkama seçenekli

bulaþýk makinesi biberon

gövdesi, biberon mamasý ve

aksesuarlarý yýkamasýnda

kullanýlan emzik sepetine

sahiptir.

Aþaðýdaki bulaþýklar bu makinede yýkanmak

için uygun deðildir

 Ahþap, fildiþi ve boncuk saplý ahþap takýmlarý.

 Paslanabilir çelik, bakýr, pirinç, beyaz maden veya

alaþýmlý maddeler.

 Isý yalýtýmlý olmayan plastik maddeler.

 Antik ya da resmi elle yapýlmýþ porselen.

 Antik gümüþler. Antik olmayan gümüþler hafif bir

program kullanýlarak yýkanabilir. Önemli olan makinede

baþka madenlerle temasa geçmemesidir.

 Bulaþýk ve çatal býçak satýn alýndýðýnda bulaþýk

makinesinde yýkamaya uygun olup olmadýðýný kontrol edin.

Kulplarýn yýkanmasý

Üst ve alt sepetin kulplarýný yýkamak için: ufak babitleme

baþlýklarýný çýkarýnýz, kulplarý da çýkarýnýz çeþme suyu ile

yýkadýktan sonra yine ayný baþlýklarý sepete tekrar takýnýz.

* Sadece bazý modellerde mevcuttur.

** Sayýsý ve pozisyonu deðiþebilir.

 Sepetleri doldurmadan önce büyük yemek artýklarýný

dökünüz, tencerelerdeki yanmýþ yemek atýklarýný

yumuþatýnýz, dolu bardaklarý ve fýncanlarý boþaltýnýz.

Sepetleri doldurduktan sonra püskürtme kollarýnýn serbest

bir þekilde dönebilmesini saðlayýnýz.

Alt sepet

Kaldýrýlabilir raflarý* kullanarak ve Sepet Yerleþtirme

örneðini dikkate alarak çok kirli bulaþýklarý yerleþtiriniz*.

 Servis tabaklarý ve büyük kapaklar: sepet kenarýna

dayayýnýz.

 Tencereler, salata kaseleri: her zaman aðýzlarý aþaðýya

gelecek þekilde yerleþtiriniz.

 Derin kap-kaçak: çapraz duracak þekilde yerleþtiriniz.

Yýkama ve kurulama sonucunun iyi olmasýný saðlamak için

alt sepetin yüzeyi üstekinden daha pürüzlüdür.

Çatal-Kaþýk Sepeti

Çatal-kaþýk sepeti bulaþýk makinesinin modeline göre

deðiþebilir.

 Býçaklar ve keskin uçlu gereçler çatal-kaþýk sepetine

uçlarý aþaðýya gelecek þekilde yerleþtirilmelidir.

Sepetini ikiye ayýrmak için*: sapýný çýkarýnýz. Sepetin iki yan

mandalý çýkarýlabilir ve üst ya da alt sepete takýlabilir.

Ýki plastik ýzgara* çatal kaþýk takýmýlarýný birbirlerinden ayýrý

tutmak için sepetin üstüne konur: çatal-kaþýk saplarý aþaðýya

gelecek þekilde, birer birer sepetin yuvalarýna yerleþtirilir.

Üst sepet

Üst sepete hafif ve hassas bulaþýklarý yerleþtiriniz:

bardaklar, çay ve kahve fincanlarý, normal ve küçük

tabaklar, fazla çukur olmayan salata kaseleri, fazla çukur

ve çok kirli olmayan tavalar, tencereler, kaplar Sepet

Yerleþtirme örneði dikkate alýnarak yerleþtirilir.

 Hafif bulaþýk: hafif bulaþýklarý su püskürmesinde

savrulmayacak þekilde yerleþtiriniz.

 Bardak ve fincanlar: raflara yerleþtiriniz**.

 Uzun ve keskin býçaklar, kepçe gibi parçalar: raflara

yerleþtiriniz**.

Üst sepetin yükseklik ayarý.

Bulaþýklarý daha kolay yerleþtirebilmek için üst sepeti

yüksek yada alçak konuma

ayarlamak mümkündür.

üst sepetin ön kýlavuz tahditlerini

dýþ tarafa doðru çekiniz ve sepeti

dýþarý çýkarýnýz; sepeti daha alçak

ya da yüksek bir konuma takýn

tamamen girene kadar kýlavuz

üzerine kaydýrýnýz ve ön kýlavuz

tahditlerini iç tarafa doðru çekerek

kapatýnýz (þekile bakýnýz).

Sepetlerin doldurulmasý

Deterjan doldurulmasý

Yýkama sonucunun olumsuz etkilenmemesi için

deterjan kutusu üzerindeki üreticinin dozaj

tavsiyelerine uyunuz. Doðru miktardan fazla

deterjan kullanmak yýkama sonucunun olumsuz

etkilemesine ve çevre kirlenmesine neden olur.

A haznesi: Yýkama deterjaný

B haznesi: Ön yýkama deterjaný

1. D düðmesine

basarak C kapaðýný

açýnýz.

2. Program çizelgesine

bakarak deterjan

dozajýný ayarlayýnýz:

 toz þeklinde ise: A ve

B haznesine

yerleþtirilmelidir.

 tablet þeklinde ise: A

haznesine ve makinenin

dibine yerleþtirilmelidir.

Açýkçasý; programa göre 1 tablet gerekirse A

haznesine, 2 tablet gerekirse makinenin dibine

yerleþtirilecektir.

3. Deterjan kalýntýlarýný tamamen temizleyiniz,

kapaðý kapatýn ve yerine iyice oturuncaya kadar

bastýrýnýz.

Çalýþtýrma ve kullanma

* Sadece bazý modellerde mevcuttur.

Çamaþýr makinesinin çalýþtýrýlmasý

1. Su musluðunu açýnýz.

2. AÇMA-KAPAMA tuþuna basýnýz: uyarý lambasý

yanacaktýr.

3. Makinenin kapaðýný açýnýz ve deterjan haznesine

yeterli miktarda deterjan koyunuz (aþaðýya

bakýnýz).

4. Sepetleri doldurunuz (Sepetlerin doldurulmasý

bölümüne bakýnýz) ve kapaðý kapatýnýz.

5. Yýkanacak bulaþýk ve kir seviyesine göre

PROGRAM SEÇÝMÝ düðmesini saatin ters yönünde

çevirerek istenilen programý seçiniz (program

çizelgesine bakýnýz).

Birkaç saniye geçtikten sonra program devreye

girer, PROGRAM TAKÝP uyarý lambasý programýn

durumunu belirtir.

Ön yýkama, Yýkama, Durulama, Kurulama.

7. Program bitiminde Kurulama uyarý lambasý

yanacaktýr.

8. PROGRAM SEÇÝMÝ düðmesini, daha önce

seçilen ayarlarý sýfýrlamak amacýyla RESET

konumuna getiriniz.

9. AÇMA-KAPAMA tuþuna basarak cihazý

kapattýnýz, su musluðunu kapattýnýz ve elektrik

þebekesinden fiþi çekiniz.

10. Makinenin kapaðýný açýnýz ve sýcak buharla

yanmamak için bulaþýklarý çýkarmadan önce birkaç

dakika bekleyiniz. Alt septeten baþlayarak

sepetleri boþaltýnýz.

Çalýþmakta olan programýn deðiþtirilmesi

Yanlýþ programýn seçilmesi durumunda makine

çalýþtýrýldýktan sonra bir dakika içerisinde

deðiþtirilebilir. PROGRAM SEÇÝMÝ düðmesini

RESET konumuna getirdikten sonra PROGRAM

TAKÝP uyarý lambasýnýn yanýp sönmesi sona erir.

Þimdi istenilen program seçilebilir.

Baþka bulaþýklarýn yerleþtirilmesi

AÇMA-KAPAMA düðmesine basýnýz, makineden

fýþkýran sýcak buhardan kaçýnarak kapaðý dikkatlice

açýnýz ve bulaþýklarý yerleþtiriniz. AÇMA-KAPAMA

tuþuna basýnýz: program tekrar baþlayacaktýr.

Makinenin yanlýþlýkla durdurulmasý

Yýkama sýrasýnda kapak açýlmasý veya elektrik

akýmý kesilmesi durumunda program duracaktýr.

Kapak kapatýldýðý veya elektrik akýmý döndüðü

zaman durdurulduðu yerden çalýþmaya devam

edecektir.

Program çizelgesi

Not:

Deterjan dozunu ayarlamaya yardýmcý olmasý için aþaðýdakilerin dikkate alýnmasý gerekir:

1 yemek kaþýðý = 15 gram toz = yaklaþýk 15 ml deterjan

1 tatlý kaþýðý = 5 gram toz = yaklaþýk 5 ml deterjan

! Ariston bulaþýk makineleri programlarýn süresini uzatabilecek otomatik filtre sistemine sahiptir.

Programlar

Deterjan

(A) = A haznesi

(B) = B haznesi

Program seçmek

için gereken

bilgiler

Program

Toz

deterjan

Sývý

deterjan

Tablet

Ön

yýkama

Kurutma

Program

süresi

(tolerans

±10% )

Çok kirli bulaþýk ve

tencere (hassas

bulaþýk uygun

deðil).

Yoðun

30 gr (A)

5 gr (B)

30 ml (A)

5 ml (B)

1 (A)

1 makinenin

dibinde

• • 2:00’

Normal kirler.

Bulaºik ve tencere.

Standart günlük

programý.

Normal

30 gr (A) 30 ml (A) 1 (A) • 1:12’

Düsük enerji tükemli

ekonomik yýkama

programý. Bulasýk

ve tencere.

Eco

25 gr (A)

5 gr (B)

25 ml (A)

5 ml (B)

1 (A) • • 2:10’

! Program sayýsý ve tipi çamaþýr makinesinin modeline göre deðiþir.

! Sadece bulaþýk makinesi içinde kullanýma uygun

olarak imal edilmiþ deterjanlarý kullanýnýz.

Endüstriyel ya da yemek tuzu kullanmayýnýz.

! Kombi deterjanlarý (2si1, 3ü1, 4ü1, etc... arada)

kullanýldýðýnda parlatýcýnýn kullanýlmasýna gerek

kalmaz, ama özellikle su sertlik seviyesi yüksek ise

tuz doldurulmasý tavsiye edilir. Tuz ve parlatýcý

doldurulmadýðý sürece TUZ EKSÝKLÝÐÝ* ve PARLATICI

EKSÝKLÝÐÝ* uyarý lambalarýnýn yanýp sönmesi

normaldýr.

Parlatýcý doldurulmasý

Parlatýcý bulaþýk üzerinden suyun akmasýný

saðlayarak bulaþýklarýn kurumasýný kolaylaþtýrýr ve

böylece su lekesi kalmaz.

Parlatýcý haznesi aþaðýdaki durumlarda

doldurulmalýdýr:

 (H) uyarý lambasýndan parlatýcý haznesinin boþ

olduðunu görünce. Uyarý lambasý açýk renk ise:

parlatýcý ekleyiniz; uyarý lambasý koyu renk ise:

Parlatýcý yeterlidir;

 Panelde PARLATICI EKSÝKLÝÐÝ uyarý lambasý

yanýp söndüðü zaman:

1. (G) kapaðý saatin tersi

yönünde çevirerek parlatýcý

haznesini açýnýz.

2. Parlatýcýyý dýþarý

akýtmadan dökünüz. Dýsarý

akmasý durumunda hemen

bir süngerle temizleyiniz.

3. Kapaðý çevirerek

kapatýnýz.

Parlatýcý dozajýnýn ayarlanmasý

Elde edilen yýkama ve kurutma sonuçlarýna göre

parlatýcýnýn dozunu ayarlayýnýz. 6 konum seçici

düðmesini (F) tornavida vasýtasýyla çevirerek

ayarlayýnýz (dozaj, fabrikada 4. konuma

ayalanmýþtýr):

 Yýkanmýþ bulaþýklarda beyaz çizgiler oluþmasý

durumunda, dozaj alçak (1-3) konuma

ayarlanmalýdýr.

 Bulaþýklarýn üstünde su damlacýklarý yada kireç

lekesi oluþmasý durumunda, dozaj yüksek konuma

(4-6) ayarlanmalýdýr.

! Kombi deterjanlarý (2si1, 3ü1,4ü1, etc... arada)

kullanýrken daha iyi bir kurutma elde etmek

istendiðinde hazne doldurulmalý ve 2. konuma

ayarlanmalýdýr.

Yenileyici tuz doldurulmasý

Daima iyi yýkama sonuçlarý elde etmek için tuz

haznesi hiçbir zaman boþ olmamalýdýr. Yenileyici tuz

sudaki kireci çözerek bulaþýk üstünde kirecin

kalmasýný engeller. Tuz haznesi bulaþýk makinesinin

alt kýsmýnda bulunur ve (Cihazýn tanýmý bölümüne

bakýnýz)aþaðýdaki durumlarda doldurulmalýdýr:

 Tuz haznesinin kapaðýna bakýldýðýnda yeþil bir

þamandra görünmediði zaman;

 Panelde TUZ EKSÝKLÝÐÝ* uyarý lambasý yanýp

söndüðü zaman;

 uyarý lambasý veya yeþil þamandra görünmediði

zaman:

yaklaþýk 30 yýkamada bir;

1. Alt sepeti çýkarýnýz ve saatin

tersi yönünde çevirerek tuz

haznesinin kapaðýný açýnýz.

2. Sadece ilk yýkama için:

hazneyi kenara kadar su ile

doldurunuz.

3. Makine ile birlikte verilen

huni vasýtasýyla (þekile

bakýnýz) hazneyi tamamen dolduracak kadar tuzu

koyunuz. Suyun azcýk taþmasý normaldýr.

4. Huniyi çýkarýp diþli kýsmýndaki tuz kalýntýlarýný

temizleyiniz ve yýkama sýrasýnda deterjan girmeyecek

þekilde ( kireç çözücü ayarý tamamen bozulabilir)

kapaðý kapatýnýz.

! Tuz doldurulduðunda korozyon olmamasý amacýyla

taþmýþ olan tuzu gidermek için bulaþýk yerleþtirmeden

makineyi çalýþtýrýnýz.

Tuz dozajýnýn ayarlanmasý*

Bulunduðunuz yerdeki su sertliðine göre tuz

ayarlamasýný yapmak mümkündür. Sular idaresi su

sertlik seviyesi hakkýnda sizi bilgilendirebilir.

1. Tuz haznesinin kapaðýný çýkarýnýz.

2. Aþaðýdaki çizelgeyi (þekile

bakýnýz) dikkate alarak kapak iç

kýsmýndaki oku + veya  yöne

döldürünüz:

Kireç çözücü ayarý, fabrikada + olarak ayarlanmýþtýr.

Kombi deterjanlarý (2si1, 3ü1, 4ü1, etc... arada)

kullanýldýðýnda tuz haznesini doldurunuz ve  olarak

ayarlayýnýz. Su sertlik seviyesi 60°fHden yüksek ise

+ olarak ayarlayýnýz.

* Sadece bazý modellerde mevcuttur.

Parlatýcý ve yenileyici tuz

Sayfa yükleniyor...

Indesit L 60 T3C TK Kullanici rehberi

Marka: Indesit

Modeli: L 60 T3C TK

Kategori: Bulaşık makineleri

Tip: Kullanici rehberi

PDF''yi indir

rapor

diğer dillerde

English: Indesit L 60 T3C TK User guide

Indesit L 60 T3C TK Kullanici rehberi

Indesit L 60 T3C TK Kullanici rehberi

diğer dillerde

İlgili makaleler

Diğer belgeler