Yamaha N-803D Kullanım kılavuzu

Yamaha
Marka
Yamaha
Modeli
N-803D
Tip
Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

EN
AV17-0052
There are two ways to update the firmware on the R-N803 and R-N803D: connect to the Internet to update directly, or
use a USB storage device. Please see the Owner’s Manual for more information on updating via the Internet. This guide
explains how to update using a USB storage device.
See the R-N803 page on the Yamaha website for more information on issues that have been resolved in the firmware
update and new functions that have been added.
Preparing the firmware
1 Have a USB storage device ready for use.
The USB storage device must fulfill the following
conditions.
• Required conditions for USB storage
device
- Supports mass storage
- Formatted as FAT16 or FAT32
- Does not feature encryption
- Blank (no data stored on the device)
2 Download the latest firmware from the
Yamaha website.
See the R-N803 page on the Yamaha website.
3 Decompress the downloaded file.
The firmware you downloaded is a compressed file.
The decompressed file (R0445-****.bin) is the
firmware data file for update (the “****” will vary,
depending on the version).
4 Save the decompressed file (R0445-****.bin)
to the root folder (topmost folder) in the USB
storage device.
Now you’re ready to update.
Updating the firmware
NOTICE
Be absolutely sure not to turn off the power while the firmware is
updating. If the power is turned off during updating, the unit may
fail to start up again.
1 Press A (POWER) on the unit to switch off
the power.
2 Insert the USB storage device that you have
prepared into the USB jack.
3 Press A (POWER) while holding down
RETURN.
“ADVANCED SETUP” will appear in the display.
4 Turn the SELECT/ENTER knob until
“UPDATE · · · USB” is shown on the display.
Note
When “UPDATE · NETWORK” is shown on the display, press
SELECT/ENTER to display “UPDATE · · · USB”.
5 Press DISPLAY.
The firmware will start updating. Once the update
has completed, “UPDATE SUCCESS” will be shown
on the display.
6 Press A (POWER) to turn off the power.
7 Pull out the USB storage device.
This completes the firmware update. Wait for at least
5 seconds after the firmware update has finished,
before turning on the power. The next time you turn
on the power, the unit will operate with the updated
firmware.
R-N803 R-N803D Update Guide
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
A (POWER)
SELECT/ENTER
RETURN
DISPLAY
DISPLAY
USB jack
Checking the firmware version
Follow the steps below to check the firmware version.
1 Press A (POWER) while holding down
RETURN.
“ADVANCED SETUP” will appear in the display,
after which the firmware version will be displayed.
2 Press A (POWER) to turn off the power.
What to do if the update is
unsuccessful
Take the actions below and then try reapplying the update,
if the update is unsuccessful.
Cause Action
The USB storage device may
not be properly connected to
the USB jack.
Check whether the USB
storage device is properly
inserted into the USB jack.
The firmware data file was
not properly saved to the USB
storage device.
Make sure that the firmware
file is saved to the root folder
(the topmost folder) of the
USB storage device.
The USB storage device is
password-protected.
Use a USB storage device that
is not password-protected.
If the firmware cannot be updated to the target version,
or the power to this device might be cut off while
updating, use the following method to update instead.
NOTICE
Be absolutely sure not to turn off the power while the
firmware is updating. If the power is turned off during
updating, the unit may fail to start up again.
1 Unplug the unit from the power outlet.
2 Make sure that A (POWER) is pushed in,
and that the USB storage device for
updating the firmware has been inserted.
3 Insert the AC plug into the power outlet
while holding down CLEAR on the unit.
The message “BaseUpdate:USB” will be shown
on the display, and the update will begin.
Once the update has completed, “UPDATE
SUCCESS” will be shown on the display.
4 Press A (POWER) to turn off the power.
5 Pull out the USB storage device.
VOLUME
PURE DIRECT
RETURN
CONNECT
PUSH - ENTER
TUNINGPRESET
BAND
MEMORY CLEAR
BASSINPUT
5V
1A
BALANCE
LR
TREBLE
LOUDNESS
FLAT
-30dB
DIMMER MODE
DISPLAY
SELECT
PHONES
YPAO MIC
SPEAKERS USB
AB
A (POWER)
CREAR
DISPLAY
USB jack
Published 12/2017 IP-B0
© 2017 Yamaha Corporation
Manual Development Group
  • Page 1 1
  • Page 2 2
  • Page 3 3

Yamaha N-803D Kullanım kılavuzu

Yamaha
Marka
Yamaha
Modeli
N-803D
Tip
Kullanım kılavuzu
Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
PDF''yi indir
rapor

diğer dillerde

İlgili makaleler