Electrolux ESL63010 Kullanım kılavuzu

user manual

instrukcja obsługi

kullanma kılavuzu

notice d'utilisation

Dishwasher

Zmywarka

Bulaşık makinesi

Lave-vaisselle

ESL63010

Electrolux. Thinking of you.

Share more of our thinking at www.electrolux.com

CONTENTS

Safety information 2

Product description 3

Control panel 4

Use of the appliance 5

Setting the water softener 5

Use of dishwasher salt 6

Use of rinse aid 7

Loading cutlery and dishes 8

Use of detergent 10

Setting and starting a washing programme

11

Washing programmes 12

Care and cleaning 13

What to do if… 14

Technical data 16

Installation 16

Water connection 16

Electrical connection 17

Environment concerns 17

Subject to change without notice

SAFETY INFORMATION

For your safety and correct operation

of the appliance, read this manual

carefully before installation and use. Al-

ways keep these instructions with the

appliance even if you move or sell it.

Users must fully know the operation

and safety features of the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean house-

hold utensils that are applicable for dish-

washers.

• Do not put solvents in the appliance. Risk

of explosion.

• Put the knives and all items with sharp

points in the cutlery basket with their

points down. If not, put in a horizontal

position in the upper basket.

• Use only branded products for dishwash-

ers (detergent, salt, rinse aid).

• If you open the door while the appliance

is in operation, hot steam can escape.

Risk of skin burns.

• Do not remove dishes from the dish-

washer before the end of the washing

programme.

• When the washing programme is com-

pleted, disconnect the mains plug from

the mains socket and close the water

tap.

• Only an authorised service engineer can

repair this appliance. Use only original

spare parts.

• Do not do repairs yourself to prevent in-

jury and damage to the appliance. Al-

ways contact your local Service Force

Centre.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have

supervision or instruction for the opera-

tion of the appliance by a person respon-

sible for their safety.

• Obey the safety instructions from the

manufacturer of the dishwasher deter-

gent to prevent burns to eyes, mouth and

throat.

• Do not drink the water from the dish-

washer. Detergent residues can stay in

your appliance.

• Always close the door when you do not

use the appliance to prevent injury and

not to stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Chil-

dren must get supervision to make sure

that they do not play with the appliance.

• Keep all the packaging away from chil-

dren. There is a risk of suffocation.

2 electrolux

• Keep all detergents in a safe area. Do not

let children touch the detergents.

• Keep children away from the appliance

when the door is open.

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not con-

nect a damaged appliance. If necessary,

contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must

do the electrical installation.

• A qualified and competent person must

do the plumbing installation.

• Do not change the specifications or mod-

ify this product. Risk of injury and dam-

age to the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth

area are damaged, that you can get

access to the inner side of the appli-

ance.

Contact your local Service Force Centre.

• Do not drill into the sides of the appliance

to prevent damage to hydraulic and elec-

trical components.

Warning! Carefully obey the

instructions for electrical and water

connections.

PRODUCT DESCRIPTION

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

9 Upper spray arm

electrolux 3

CONTROL PANEL

5 4

321

AB

1 On/off button

2 Delay start button

3 Programme selection/cancel button / (PROG. / CANCEL)

4 Indicator lights

5 Programme indicator lights

Indicator lights

Comes on when the washing programme is

completed. Auxiliary functions:

• Level of the water softener.

• Activation/deactivation the audible signals.

• An alarm if the appliance has a malfunction.

1)

Comes on when it is necessary to fill the rinse

aid container. Refer to 'Use of rinse aid'.

1)

Comes on when it is necessary to fill the salt

container. Refer to 'Use of dishwasher salt'.

After you fill the container, the salt indicator light

can continue to stay on for some hours. This

does not have an unwanted effect on the opera-

tion of the appliance.

1) When the salt and/or rinse aid containers are empty, the related indicator lights do not come on while a washing

programme operates.

Programme selection/cancel button

Use the programme selection/cancel button

for these operations:

• To set the washing programme. Refer to

the chapter 'Setting and starting a wash-

ing programme'.

• To set the water softener. Refer to the

chapter 'Setting the water softener'.

• To deactivate/activate the audible sig-

nals. Refer to the section 'Audible sig-

nals'.

• To cancel a washing programme in pro-

gress. Refer to the chapter 'Setting and

starting a washing programme'.

Delay start button

Use the delay start button to delay the start

of the washing programme with an interval

of 3 hours. Refer to the chapter 'Setting

and starting a washing programme'.

Setting mode

The appliance is in setting mode when all

the programme indicator lights are off and

the end indicator light flashes.

4 electrolux

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

– To deactivate/activate the audible sig-

nals.

If a programme indicator light is on, cancel

the programme to go back to the setting

mode. Refer to the chapter "Setting and

starting a washing programme".

Programme indicator lights A and B

Apart the selection of the corresponding

washing programme, these lights have an

auxiliary functions:

•The adjustment of the water softener lev-

el.

• Deactivation/activation of the audible sig-

nals.

Audible signals

You can hear an audible signal:

• At the end of the washing programme.

• When the appliance has a malfunction.

The activation of the audible signals is set at

the factory.

Do these steps to deactivate the audible

signals:

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press and hold the programme selec-

tion/cancel button until programme in-

dicator light A flashes and programme

indicator light B comes on.

4. Press the programme selection/cancel

button again.

– Programme indicator light A comes

on.

– Programme indicator light B starts to

flash.

5. Wait until programme indicator light A

goes off.

– Programme indicator light B contin-

ues to flash.

– The end indicator light comes on.

The audible signals are activated.

6. Press the programme selection/cancel

button again.

– The end indicator light goes off.

The audible signals are deactivated.

7. Switch off the appliance to save the op-

eration.

Do these steps to activate the audible sig-

nals:

1. Do the above procedure until the end

indicator light comes on.

USE OF THE APPLIANCE

Refer to the following instructions for each

step of procedure:

1. Make a check if the water softener level

is correct for the water hardness in your

area. If necessary set the water soften-

er.

2. Fill the salt container with dishwasher

salt.

3. Fill the rinse aid dispenser with rinse

aid.

4. Load cutlery and dishes into the dish-

washer.

5. Set the correct washing programme for

the type of load and soil.

6. Fill the detergent dispenser with the

correct quantity of detergent.

7. Start the washing programme.

If you use detergent tablets, refer to the

chapter 'Use of detergent'.

SETTING THE WATER SOFTENER

The water softener removes minerals and

salts from the water supply. Minerals and

salts can have bad effect on the operation

of the appliance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international

unit for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact

your local water authority.

electrolux 5

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10

43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9

37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8

29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7

23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6

19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5

15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4

11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2

< 4 < 7 < 0,7 < 5

1

1)

1

1)

1) No use of salt required.

You must set the water softener man-

ually and electronically.

Manual adjustment

The appliance is set at the factory at

position 2.

1. Open the door.

2. Remove the lower basket.

3. Turn the water hardness dial to position

1 or 2 (refer to the chart).

4. Install the lower basket.

5. Close the door.

Electronic adjustment

The water softener is set at the factory

at level 5.

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press and hold the programme selec-

tion/cancel button.

4. Release the programme selection/can-

cel button when programme indicator

light A starts to flash and programme

indicator light B comes on.

5. Wait until programme indicator light B

goes off.

– Programme indicator light A starts to

flash.

– The end indicator light starts to flash.

6. Press the programme selection/cancel

button one time.

– Programme indicator light A starts to

flash.

– The setting function of the water soft-

ener is activated.

– The end indicator light flashes to

show the level of the water softener.

Example: 5 flashes, pause, 5 flashes,

pause, etc... = level 5.

7. Press the programme selection/cancel

button one time to increase the water

softener level by one step.

8. Press the on/off button to save the op-

eration.

USE OF DISHWASHER SALT

Caution! Only use dishwashers salt.

Types of salt that are not applicable for

dishwashers cause damage to the

water softener.

Caution! Grains of salt and salty water

on the bottom of the appliance can

cause corrosion. Fill the appliance with

salt before you start a washing

programme to prevent corrosion.

6 electrolux

Do these steps to fill the salt container:

1. Turn the cap anticlockwise to open the

salt container.

2. Fill the salt container with 1 litre of wa-

ter (only the first operation).

3. Use the funnel to fill the salt container

with salt.

4. Remove the salt around the opening of

the salt container.

5. Turn the cap clockwise to close the salt

container.

It is normal that water overflows from

the salt container when you fill it with

salt.

When you set electronically the water soft-

ener to level 1, the salt indicator light does

not stay on.

USE OF RINSE AID

Caution! Only use branded rinse aid

for dishwashers.

Do not fill the rinse aid dispenser with

other products (e.g. dishwasher clean-

ing agent, liquid detergent). This can

cause damage to the appliance.

Rinse aid makes it possible to dry the

dishes without streaks and stains.

Rinse aid is automatically added during

the last rinsing phase.

Do these steps to fill the rinse aid dispens-

er:

1. Press the release button (A) to open the

rinse aid dispenser.

electrolux 7

2. Fill the rinse aid dispenser with rinse

aid. The mark 'max.' shows the maxi-

mum level.

3. Remove the spilled rinse aid with an

absorbent cloth to prevent too much

foam during the subsequent washing

programme.

4. Close the rinse aid dispenser.

Adjusting the rinse aid dosage

The rinse aid is set at the factory at position

4.

You can set the rinse aid dosage between

position 1 (lowest dosage) and position 6

(highest dosage).

1. Turn the rinse aid dial to increase or de-

crease the dosage.

– Increase the dosage if there are wa-

ter droplets or limescale on the

dishes.

– Decrease the dosage if there are

streaks, whitish stains or bluish layers

on the dishes.

LOADING CUTLERY AND DISHES

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable

for dishwashers.

Do not use the appliance to clean objects

that can absorb water (sponges, household

cloths, etc.).

• Before you load cutlery and dishes, do

these steps:

– Remove all food remainings and deb-

ris.

– Make burnt, remaining food in pans

soft.

• While you load cutlery and dishes, do

these steps:

– Load hollow items (e.g. cups, glasses

and pans) with the opening down.

– Make sure that water does not collect

in the container or in a deep base.

– Make sure that cutlery and dishes do

not lie inside one another.

– Make sure that cutlery and dishes do

not cover other cutlery and dishes.

– Make sure that glasses do not touch

other glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick

coatings can keep water droplets. Plastic

items do not dry as well as porcelain and

steel items.

• Put light items in the upper basket. Make

sure that the items do not move.

Caution! Make sure that the spray

arms can move freely before you start

a washing programme.

Warning! Always close the door after

you load or unload the appliance. An

open door can be dangerous.

Lower basket

Put saucepans, lids, plates, salad bowls

and cutlery in the lower basket. Arrange

service dishes and large lids around the

edge of the basket.

8 electrolux

Cutlery basket

Warning! Do not put long-bladed

knives in a vertical position. Arrange

long and sharp cutlery horizontally in

the upper basket. Be careful with sharp

items.

Put forks and spoons with the handles

down.

Put knives with the handles up.

Mix spoons with other cutlery to prevent

them to bond together.

Use the cutlery grid. If the dimensions of the

cutlery prevent the use of the cutlery grid,

you can remove it.

Upper basket

The upper basket is for plates (maximum

24 cm in diameter), saucers, salad bowls,

cups, glasses, pots and lids. Arrange the

items to let water touch all surfaces.

Prevent to put plates in the first three

sectors in the front part of the basket.

Make sure the plates tilt forward.

Put glasses with long stems in the cup

racks with the stems up. For longer items,

fold the cup racks up.

Adjustment of the height of the upper

basket

If you put large plates in the lower basket,

first move the upper basket to the upper

position.

Caution! Adjust the height before you

load the upper basket.

Maximum height of the dishes

upper bas-

ket

lower

basket

electrolux 9

Maximum height of the dishes

Upper position 20 cm 31 cm

Lower position 24 cm 27 cm

Do these steps to move the upper basket

to the upper position:

1. Move the front runner stops (A) out.

2. Pull the basket out.

3. Put the basket in the upper position.

4. Put back the front runner stops (A) in

their initial position.

Caution! If the basket is in the upper

position, do not put cups on the cup

racks.

USE OF DETERGENT

Only use detergents (powder, liquid or

tablet) that are applicable for dishwash-

ers.

Follow the data on the packaging:

• Dosage recommended by the manu-

facturer.

• Storage recommendations.

Do not use more than the correct

quantity of detergent to save an envi-

ronment.

Do these steps to fill the detergent dispens-

er:

1. Open the lid of the detergent dispenser.

2. Fill the detergent dispenser (A) with de-

tergent. The marking shows the dos-

age:

20 = approximately 20 g of detergent

30 = approximately 30 g of detergent.

3. If you use a washing programme with

prewash phase, put more detergent in

the prewash detergent compartment

(B).

A

B

10 electrolux

4. If you use detergent tablets, put the de-

tergent tablet in the detergent dispens-

er (A).

5. Close the lid of the detergent dispens-

er. Press the lid until it locks into posi-

tion.

Different brands of detergent dissolve

in different times. Some detergent tab-

lets do not have the best cleaning re-

sults during short washing pro-

grammes. Use long washing pro-

grammes when you use detergent tab-

lets to fully remove the detergent.

Use of combi detergent tablets

These tablets contain agents such as deter-

gent, rinse aid and dishwasher salt. Some

types of tablets can contain other agents

When you use tablets, that contain special

salt and rinse aid, it is not necessary to fill

the salt and rinse aid containers. In this

condition the rinse aid indicator light stays

on when the appliance is switched on.

1. Do a check if these tablets are applica-

ble for the local water hardness. Refer

to the instructions from the manufactur-

er.

2. Select the lowest setting for the water

hardness and rinse aid dosage.

Do these steps if the drying results are not

satisfactory

1. Fill the rinse aid dispenser with rinse

aid.

2. Set the rinse aid dosage to position 2.

To use normal detergent again

1. Fill the salt container and rinse aid dis-

penser.

2. Adjust the water hardness setting to

the highest level.

3. Do a washing programme without

dishes.

4. Adjust the water softener to the water

hardness in your area.

5. Adjust the rinse aid dosage.

SETTING AND STARTING A WASHING PROGRAMME

Set the washing programme with the

door ajar. The washing programme on-

ly starts after you close the door. Until

then it is possible to modify the set-

tings.

Do these steps to set and start a washing

programme:

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press the programme selection/cancel

button again and again to set the

washing programme. Refer to the

chapter 'Washing programmes'.

– The programme indicator light comes

on.

4. Close the door.

– The washing programme starts auto-

matically.

When the washing programme oper-

ates, you cannot change the pro-

gramme. Cancel the washing pro-

gramme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

electrolux 11

Cancelling a washing programme

1. Press and hold the programme selec-

tion/cancel button for approximately 3

seconds.

– The programme indicator light goes

off.

– The end indicator light starts to flash.

2. Release the programme selection/can-

cel button to cancel the washing pro-

gramme.

At this time you can do these steps:

1. Switch off the appliance.

2. Set a new washing programme.

Fill the detergent dispenser with detergent

before you set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point

of interruption.

Setting and starting a washing

programme with delay start

1. Press the on/off button.

2. Set a washing programme.

– The programme indicator light comes

on.

3. Press the delay start button.

– The delay start indicator light comes

on.

4. Close the door.

– The countdown of the delay start

starts.

– When the countdown is completed,

the washing programme starts auto-

matically.

Do not open the door during the count-

down to prevent interruption of the

countdown. When you close the door

again, the countdown continues from

the point of interruption.

Cancelling a delay start:

1. Open the door.

2. Press the delay start button.

– The delay start indicator light goes

off.

3. Close the door.

– The programme starts immediately.

End of the washing programme

Switch off the appliance in these condi-

tions:

• The appliance stops automatically.

• The audible signals for the end of the

programme operate.

1. Open the door.

– The end indicator light comes on.

– The programme indicator light stays

on.

2. Press the on/off button.

3. For better drying results, keep the door

ajar for some minutes before you re-

move the dishes.

Let the dishes cool down before you re-

move them from the appliance. Hot dishes

are easily damaged.

Removing the load

• First remove items from the lower basket,

then from the upper basket.

• There can be water on the sides and

door of the appliance. Stainless steel be-

comes cool more quickly than the dishes.

WASHING PROGRAMMES

Washing programmes

Programme

Degree of

soil

Type of

load

Programme description

Heavy soil

Crockery,

cutlery, pots

and pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Normal soil

Crockery,

cutlery, pots

and pans

Prewash

Main wash up to 65°C

2 intermediate rinses

Final rinse

Drying

12 electrolux

Programme

Degree of

soil

Type of

load

Programme description

1)

Normal or

light soil

Crockery

and cutlery

Main wash up to 60°C

Final rinse

2)

Normal soil

Crockery

and cutlery

Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

Any

Partial load

(to be com-

pleted later

in the day)

1 cold rinse (to prevent food scraps to

bond).

Detergent is not necessary with this pro-

gramme.

1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load

breakfast and dinner crockery and cutlery.

2) Test programme for test institutes. Please refer to separate leaflet supplied, for test data.

Consumption values

Programme Programme duration

(in minutes)

Energy consumption

(in kWh)

Water consumption

(in litres)

85-95 1,8-2,0 22-25

100-110 1,4-1,6 19-21

30 0,9 9

130-140 1,0-1,2 14-16

12 0,1 5

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change

these values.

CARE AND CLEANING

Warning! Switch the appliance off

before you clean the filters.

Cleaning the filters

Caution! Do not use the appliance

without the filters. Make sure that the

installation of the filters is correct.

Incorrect installation will cause

unsatisfactory washing results and

damage to the appliance.

If necessary, clean the filters. Dirty filters de-

crease the washing results.

The dishwasher has three filters:

1. coarse filter (A)

2. microfilter (B)

3. flat filter (C)

A

B

C

A

B

C

Do these steps to clean the filters:

1. Open the door.

2. Remove the lower basket.

electrolux 13

3. To unlock the filter system, turn the

handle on the microfilter (B) approxi-

mately 1/4 anticlockwise.

4. Remove the filter system.

5. Hold the coarse filter (A) by the handle

with the hole.

6. Remove the coarse filter (A) from the

microfilter (B).

7. Remove the flat filter (C) from the bot-

tom of the appliance.

D

8. Clean the filters below running water.

9. Put the flat filter (C) in the bottom of the

appliance. Install the flat filter correctly

under the two guide (D).

10. Put the coarse filter (A) in the microfilter

(B) and push the filters together.

11. Put the filter system in position.

12. To lock the filter system, turn the han-

dle on the microfilter (B) clockwise until

it lock in position.

13. Install the lower basket.

14. Close the door.

Do not remove the spray arms.

If the holes in the spray arms become clog-

ged, remove remaining parts of soil with a

cocktail stick.

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth.

Only use neutral detergents. Do not use

abrasive products, scouring pads or sol-

vents (acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C.

The manufacturer is not responsible for

damage because of frost.

If not possible, empty the appliance and

close the door. Disconnect the water inlet

hose and remove water from the water inlet

hose.

WHAT TO DO IF…

The appliance does not start or stops dur-

ing operation.

If there is a fault, first try to find a solution to

the problem yourself. If you cannot find a

solution to the problem yourself, contact

the Service Force Centre.

Caution! Switch off the appliance

before you do the below suggested

corrective actions.

14 electrolux

Fault code and malfunction Possible cause and solution

• continuous flash of the light of the

running programme

• intermittent audible signal

• 1 flash of the end indicator light

The appliance does not fill with wa-

ter

.

• The water tap is blocked or furred with limescale.

Clean the water tap.

• The water tap is closed.

Open the water tap.

• The filter in the water inlet hose is blocked.

Clean the filter.

• The connection of the water inlet hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• intermittent audible signal

• 2 flashes of the end indicator light

The appliance will not drain the wa-

ter.

• There is a blockage in the sink spigot.

Clean the sink spigot.

• The connection of the water drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is correct.

• continuous flash of the light of the

running programme

• intermittent audible signal

• 3 flashes of the end indicator light

Anti-flood device operates

• Close the water tap and contact your local Service Force

Centre.

The programme does not start • The appliance door is not closed.

Close the door.

• Mains plug is not connected in.

Put in the mains.

• The fuse has blown out in the household fuse box.

Replace the fuse.

• Delay start is set.

Cancel the delay start to start the programme immediately.

After the check, switch on the appliance.

The programme continues from the point of

interruption. If the malfunction shows again,

contact your Service Force Centre.

These data are necessary to help you

quickly and correctly:

•Model (Mod.)

• Product number (PNC)

• Serial number (S.N.)

For these data, refer to the rating plate.

Write the necessary data here:

Model description : ..........

Product number : ..........

Serial number : ..........

The cleaning results are not satisfactory

The dishes are not clean • The selected washing programme is not applicable for the type of

load and soil.

• The baskets are loaded incorrectly so that water cannot reach all

surfaces.

• Spray arms do not turn freely because of incorrect arrangement of

the load.

• The filters are dirty or not correctly installed.

• The quantity of detergent is too little or missing.

Limescales particles on the

dishes

• The salt container is empty.

• The water softener is adjusted on a wrong level.

• The salt container cap is not closed correctly.

The dishes are wet and dull • No rinse aid has been used.

• The rinse aid dispenser is empty.

There are streaks, milky

spots or a bluish coating on

glasses and dishes

• Decrease the rinse aid dosage.

electrolux 15

The cleaning results are not satisfactory

Dry water drop signs on

glasses and dishes

• Increase rinse aid dosage.

• The detergent can be the cause.

TECHNICAL DATA

Dimensions Width cm 59,6

Height cm 81,8-87,8

Depth cm 55,5

Electrical connection - Voltage -

Overall power - Fuse

Information on the electrical connection is given on the rating

plate on the inner edge of the dishwasher door.

Water supply pressure Minimum 0,5 bar (0,05 MPa)

Maximum 8 bar (0,8 MPa)

Capacity Place settings 12

INSTALLATION

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Important! Obey the instructions in the

enclosed template to:

• Build-in the appliance.

• Install the furniture panel.

• Connect to the water supply and drain.

Install the appliance under a counter (kitch-

en worktop or sink).

If a repair is necessary, the appliance must

be easily accessible for the engineer.

Put the appliance adjacent to a water tap

and a drain.

For the venting of the dishwasher only wa-

ter fill, water drain and power supply cable

openings are necessary.

The dishwasher has adjustable feet to allow

the adjustment of the height.

Make sure that the water inlet hose, the

drain hose and the supply cable are not

kinked or squashed, when you insert the

machine.

Attaching the appliance to the adjacent

units

Make sure that the counter below which

you attach the appliance is a safe structure

(adjacent kitchen units, cabinets, wall).

Adjusting the level of the appliance

Make sure that the appliance is level to

close and seal the door correctly. If the level

of the appliance is correct, the door does

not catch on the sides of the cabinet. If the

door does not close correctly, loosen or

tighten the adjustable feet until the appli-

ance is level.

WATER CONNECTION

Water inlet hose

Connected the appliance to a hot (max.

60°) or cold water supply.

If the hot water comes from alternative

sources of energy that are more environ-

mentally friendly (e.g. solar or photovoltaic

panels and aeolian), use a hot water supply

to decrease energy consumption.

Connect the inlet hose to a water tap with

an external thread of 3/4”.

Caution! Do not use connection hoses

from an old appliance.

The water pressure must be in the limits (re-

fer to 'Technical data'). Make sure that the

local water authority gives you the average

mains pressure in your area.

Make sure that there are no kinks in the

water inlet hose and that the water inlet

hose is not squashed or entangled.

Fit the locknut correctly to prevent water

leaks.

16 electrolux

Caution! Do not connect the appliance

to new pipes or pipes that are not used

for a long time. Let the water run for

some minutes, then connect the inlet

hose.

Water drain hose

1. Connect the water drain hose to the

sink spigot and attach it under the work

surface. This prevents that the waste

water from the sink goes back into the

appliance.

2. Connect the water drain hose to a

stand pipe with vent-hole (minimum in-

ternal diameter 4 cm).

max 85 cm

min 40 cm

max 400 cm

Make sure that the drain hose is not bent or

squashed to prevent that the water drains

does not drain correctly.

Remove the sink plug when the appliance

drains the water to prevent that the water

goes back into the appliance.

A drain hose extension must not be longer

than 2 m. The internal diameter must not be

smaller than the diameter of the hose.

If you connect the water drain hose to a

trap spigot under the sink, remove the plas-

tic membrane (A). If you do not remove the

membrane, remaining food can cause a

blockage in the drain hose spigot

The appliance has a security feature to

prevent that dirty water goes back into

the appliance. If, the spigot of the sink

has a 'non-return valve', this valve can

cause the appliance to drain incorrect-

ly. Remove the non-return valve.

Caution! Make sure that the water

couplings are tight to prevent water

leakage.

ELECTRICAL CONNECTION

Warning! The manufacturer is not

responsible if you do not follow these

safety precautions.

This appliance needs to be earthed ac-

cording to safety precautions.

Make sure that the rated voltage and

type of power on the rating plate agree

with the voltage and the power of the

local power supply.

Always use a correctly installed shock-

proof socket.

Do not use multi-way plugs, connec-

tors and extension cables. There is a

risk of fire.

Do not replace the mains cable your-

self. Contact the Service Force Centre.

Make sure that the mains plug is ac-

cessible after installation.

Do not pull the mains cable to discon-

nect the appliance. Always pull the

mains plug.

ENVIRONMENT CONCERNS

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will

help prevent potential negative

electrolux 17

consequences for the environment and

human health, which could otherwise be

caused by inappropriate waste handling of

this product. For more detailed information

about recycling of this product, please

contact your local council, your household

waste disposal service or the shop where

you purchased the product.

The packaging materials are environmental-

ly friendly and can be recycled. The plastic

components are identified by markings, e.g.

>PE<, >PS<, etc. Discard the packaging

materials in the applicable container at the

community waste disposal facilities.

Warning! To discard the appliance,

follow the procedure:

• Pull the mains plug out of the socket.

• Cut off the mains cable and mains

plug and discard them.

• Discard the door catch. This pre-

vents the children to close them-

selves inside the appliance and en-

danger their lives.

18 electrolux

Electrolux. Thinking of you.

Aby dowiedzieć się więcej o naszej filozofii, odwiedź naszą

stronę internetową www.electrolux.com

SPIS TREŚCI

Informacje dotyczące bezpieczeństwa 19

Opis urządzenia 20

Panel sterowania 21

Eksploatacja urządzenia 22

Ustawianie zmiękczacza wody 23

Wsypywanie soli do zmywarki 24

Wlewanie płynu nabłyszczającego 24

Wkładanie sztućców i naczyń 25

Stosowanie detergentu 27

Wybór i uruchamianie programu zmywania

29

Programy zmywania 30

Konserwacja i czyszczenie 31

Co zrobić, gdy… 32

Dane techniczne 34

Instalacja 34

Podłączenie do sieci wodociągowej 34

Podłączenie do sieci elektrycznej 35

Ochrona środowiska 36

Producent zastrzega sobie możliwość wprowadzenia zmian bez wcześniejszego

powiadomienia

INFORMACJE DOTYCZĄCE BEZPIECZEŃSTWA

Aby zapewnić bezpieczeństwo użytko-

wania i prawidłowe działanie urządze-

nia, przed przystąpieniem do instalacji i

obsługi należy dokładnie przeczytać ni-

niejszą instrukcję. Instrukcję przecho-

wywać zawsze razem z urządzeniem,

również w razie jego przeniesienia lub

odsprzedaży. Użytkownicy muszą w

pełni poznać działanie i funkcje ochron-

ne urządzenia.

Prawidłowe użytkowanie

•Urządzenie jest przeznaczone wyłącznie

do użytku domowego.

•Urządzenie służy wyłącznie do czyszcze-

nia naczyń i sprzętów domowych nadają-

cych się do mycia w zmywarce.

•Nie używać rozpuszczalników w urządze-

niu. Zagrożenie wybuchem.

•No

że i wszystkie przedmioty z ostrymi

końcówkami umieszczać w koszyku na

sztućce, ostrym końcem skierowanym w

dół. Można też układać je w pozycji po-

ziomej w koszu górnym.

•Używać wyłącznie markowych produk-

tów do zmywarek do naczyń (detergent,

sól, płyn nabłyszczający).

• Po otwarciu drzwi podczas pracy urzą-

dzenia może dojść do uwolnienia gorącej

pary. Ryzyko poparzenia skóry.

•Nie wyjmować naczyń ze zmywarki przed

zakończeniem programu mycia.

•Po zakończeniu zmywania wyjąć wtyczkę

z gniazdka i zamknąć zawór dopływu

wody.

•Urządzenie może być naprawiane wy-

łącznie przez montera z autoryzowanego

serwisu. Używać wyłącznie oryginalnych

części zamiennych.

• Nie wymieniać ich samodzielnie, aby

uniknąć obrażeń i uszkodzenia urz

ądze-

nia. Zawsze kontaktować się z lokalnym

autoryzowanym serwisem.

Ogólne zasady bezpieczeństwa

•Urządzenie nie jest przeznaczone do

użytku przez osoby (w tym dzieci) o ogra-

niczonych zdolnościach fizycznych, sen-

sorycznych czy umysłowych, a także nie-

posiadające doświadczenia ani odpo-

wiedniej wiedzy. Osoby te mogą obsługi-

wać urządzenie wyłącznie pod nadzorem

i po uzyskaniu instrukcji od osoby odpo-

wiedzialnej za ich bezpieczeństwo.

•Przestrzegać instrukcji dotyczących bez-

pieczeństwa, dostarczonych przez pro-

ducentów detergentów, aby uniknąć po-

parzeń oczu, ust i gardła.

electrolux 19

•Nie pić wody ze zmywarki. W zmywarce

mogą być obecne pozostałości deter-

gentów.

• Zawsze zamykać drzwi urządzenia, gdy

nie jest ono używane, aby uniknąć obra-

żeń i nie potknąć się o otwarte drzwi.

•Nie siadać ani nie stawać na otwartych

drzwiach.

Bezpieczeństwo dzieci

•Urządzenie może być użytkowane wy-

łącznie przez osoby dorosłe. Dzieci nale-

ży pilnować, aby mieć pewność, że nie

bawią się urządzeniem.

• Opakowanie przechowywać w miejscu

niedostępnym dla dzieci. Istnieje ryzyko

uduszenia.

• Wszystkie detergenty należy przechowy-

wać w bezpiecznym miejscu. Nie dopuś-

cić do kontaktu dzieci z detergentami.

• Dzieci nie powinny znajdować się w po-

bliżu urządzenia, gdy jego drzwi są ot-

warte.

Instalacja

•Upewnić się, że urządzenie nie uległo

uszkodzeniu w czasie transportu. Nie

podłączać uszkodzonego urządzenia. W

razie potrzeby skontaktować się z do-

stawcą.

• Przed pierwszym użyciem usunąć

wszystkie materiały opakowaniowe.

• Instalację elektryczną powierzyć wykwali-

fikowanemu i kompetentnemu specjaliś-

cie.

•Podłączenie wodociągowe i kanalizacyjne

powierzyć wykwalifikowanemu i kompe-

tentnemu specjaliście.

• Nie zmieniać specyfikacji ani nie modyfi-

kować produktu. Ryzyko odniesienia ob-

rażeń i uszkodzenia urządzenia.

•Nie używać urządzenia:

–jeżeli przewód zasilający lub węże

wodne są uszkodzone,

–jeżeli panel sterowania, blat roboczy

lub cokół są uszkodzone w sposób da-

jący dostęp do wnętrza urz

ądzenia.

Skontaktować się z lokalnym autoryzo-

wanym serwisem.

• Nie wolno nawiercać ścian bocznych

urządzenia, aby uniknąć uszkodzenia

części hydraulicznych lub elektrycznych.

Ostrzeżenie! Dokładnie przestrzegać

instrukcji dotyczących połączeń

elektryczności oraz wody.

OPIS URZĄDZENIA

1 Kosz górny 2 Pokrętło regulacji zmiękczania wody

20 electrolux

Sayfa yükleniyor ...

Electrolux ESL63010 Kullanım kılavuzu

Electrolux ESL63010 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler