Yamaha YAS-106 El kitabı

Tip
El kitabı
G
Front Surround System
Système Surround Frontal
Owner’s Manual
Mode d’emploi
English
Français
FREN
2 En
To assure the finest performance, please read this manual carefully. Keep it in a safe
place for future reference.
Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight,
heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the
following minimum clearances.
Top: 10 cm (4 in), Rear: 10 cm (4 in), Sides: 10 cm (4 in)
Locate this unit away from other electrical appliances, motors, or transformers to
avoid humming sounds.
Do not expose this unit to sudden temperature changes from cold to hot, and do not
locate this unit in an environment with high humidity (i.e. a room with a humidifier)
to prevent condensation inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
Avoid installing this unit where foreign objects may fall onto this unit and/or this unit
may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
Other components, as they may cause damage and/or discoloration on the surface
of this unit.
Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or
personal injury.
Containers with liquid in them, as they may fall and liquid may cause electrical
shock to the user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc., in order not to
obstruct heat radiation. If the temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all connections are complete.
Do not operate this unit upside-down. It may overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp the plug; do not pull
the cable.
Do not clean this unit with chemical solvents; this might damage the finish. Use a
clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit with a higher voltage
than specified is dangerous and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any damage resulting from use of this
unit with a voltage other than specified.
To prevent damage by lightning, keep the power cable and outdoor antennas
disconnected from a wall outlet or the unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel
when any service is needed. The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e. vacation), disconnect
the AC power plug from the wall outlet.
Be sure to read the “Troubleshooting” section on common operating errors before
concluding that this unit is faulty.
Before moving this unit, press to set this unit in standby mode, and disconnect the
power supply cable from the wall outlet.
Condensation will form when the surrounding temperature changes suddenly.
Disconnect the power supply cable from the outlet, then leave the unit alone.
Install this unit near the wall outlet and where the AC power plug can be reached
easily.
Secure placement or installation is the owner’s responsibility. Yamaha shall not be
liable for any accident caused by improper placement or installation of speakers.
Keep the product out of reach of children to avoid them swallowing small parts.
Notes on remote controls and batteries
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following places:
places of high humidity, such as near a bath
places of high temperatures, such as near a heater or a stove
places of extremely low temperatures
dusty places
Do not expose the remote control sensor of this unit to direct sunlight or lighting such
as inverted fluorescent lamps.
If the batteries grow old, the effective operation range of the remote control decreases
considerably. If this happens, replace the batteries with two new ones as soon as
possible.
Exhausted batteries may leak. If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before installing new
batteries.
Do not carry batteries in a pocket or purse with metal objects like coins, etc.
Do not throw away batteries with general house waste. Dispose of them correctly in
accordance with your local regulations.
Keep batteries away from children. If a battery is accidentally swallowed, contact
your doctor immediately.
When not planning to use the remote control for long periods of time, remove the
batteries from the remote control.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
En 3
Do not charge or disassemble the supplied batteries.
The batteries shall not be exposed to excessive heat such as sunshine, fire or like.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
CAUTION
Replace only with the same type or equivalent type.
Risk of explosion if battery is incorrectly replaced.
The remote control supplied with this product contains a coin/button cell battery. If
the coin/button cell battery is swallowed, it can cause severe internal burns in just 2
hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment does
not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
Where the MAINS plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from
the AC power source even if you turn off this unit by . In this state, this unit is
designed to consume a very small quantity of power.
Do not use this unit within 22 cm (9 inches) of persons with a heart pacemaker
implant or defibrillator implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical facilities.
The name plate is located on the bottom of the unit.
OBSERVERA
Apparaten kopplas inte bort från växelströmskällan (nätet) så länge som den är
ansluten till vägguttaget, även om själva apparaten har stängts av.
ADVARSEL
Netspæendingen til dette apparat er IKKE afbrudt, sålæenge netledningen siddr i en
stikkontakt, som er t endt – også selvom der or slukket på apparatets afbryder.
VAROITUS
Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko laitetta verkosta.
Information for Users on Collection and Disposal of Old
Equipment and Used Batteries
These symbols on the products, packaging, and/or
accompanying documents mean that used electrical and
electronic products and batteries should not be mixed with
general household waste. For proper treatment, recovery and
recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national
legislation and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will
help to save valuable resources and prevent any potential
negative effects on human health and the environment which
could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old
products and batteries, please contact your local municipality,
your waste disposal service or the point of sale where you
purchased the items.
[Information on Disposal in other Countries outside
the European Union]
These symbols are only valid in the European Union. If you wish
to discard these items, please contact your local authorities or
dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol
examples):
This symbol might be used in combination with a chemical
symbol. In this case it complies with the requirement set by the
Directive for the chemical involved.
4 En
Contents
CAUTION: READ THIS BEFORE OPERATING
YOUR UNIT....................................................... 2
Supplied items ................................................ 5
Features........................................................... 8
Frequently asked questions........................... 9
Part names and functions ............................ 10
The unit (front panel/top panel)..................................10
The unit (rear panel).........................................................11
Installation .................................................... 12
Installing the unit on a TV stand, etc..........................12
Mounting the unit on a wall..........................................12
Connections .................................................. 14
Operations..................................................... 17
Operating the unit by TV’s remote control
(HDMI control)....................................................................20
Listening to the sound from a Bluetooth
device............................................................. 21
Settings ..........................................................24
Configuring the HDMI control function................... 24
Configuring HDMI audio output ................................ 24
Enabling/disabling the auto power standby
function ............................................................................... 25
Initializing the unit........................................................... 25
Troubleshooting............................................26
Specifications ................................................31
About this manual
NOTE
This indicates precautions for use of the product and its feature
limitations.
HINT
This indicates supplementary explanations for better use.
En 5
Supplied items
Make sure you have received all of the following items.
The unit
Remote control
A CR2025 Lithium battery has
already been inserted into the
remote control.
Optical digital audio cablePower cable
Mounting template
Use when mounting the unit on a wall
Spacers × 2
Use when mounting the unit on a wall
Owner’s Manual (this booklet)
6 En
Preparing the remote control
Remove the battery’s insulating strip before attempting to use the
remote control.
Operating range of the remote control
Operate the remote control within the range as shown below. When
the unit is mounted on a wall, point the remote control at the remote
control sensor on the top panel (p. 12).
Battery’s insulating strip
Remote control sensor
Within 6 m (20 ft)
En 7
Replacing the battery in the remote control
Press and hold the release tab in the direction indicated by ,
and slide the battery holder out in the direction indicated by .
Battery holder
Release tab
CR2025 Lithium
battery
8 En
Features
This front surround system is easily installed and has a built-in subwoofer for enjoying powerful and realistic sound
with connection to a TV or other devices.
Transmission of 4K high dynamic range (HDR) video supported
Enjoy high-resolution video from a cable or satellite set top box, or a BD/DVD player. When a TV that supports Audio Return Channel (ARC)
is used, this ARC-compatible unit can be connected to the TV via a single HDMI cable (p. 14).
•HDMI control function
Link TV and unit functions using the TV’s remote control (p. 20).
Bluetooth connection
Easily play content from a Bluetooth-compatible smartphone, tablet, or computer (p. 21).
Our exclusive Compressed Music Enhancer technology improves sound quality and characteristics, and can be used to enjoy realistic and
impressive sound.
HOME THEATER CONTROLLER app
HOME THEATER CONTROLLER, a free app for smartphones, allows you to easily operate the unit using a smartphone (p. 23).
Bass extension
Boost low bass levels to enjoy more powerful sound (p. 18).
•Clear voice
This feature makes speech, such as dialog and narration, clearer (p. 18).
En 9
Frequently asked questions
The following section covers popular functions and frequently asked questions about the unit.
Q1
Can I use the TV’s remote control to operate the unit?
A1
Yes. When the unit is connected to a TV via HDMI cable, the
TV’s remote control can be used to operate both the TV and
the unit (p. 20).
Q2
Can I improve the clarity of dialogue?
A2
Yes. Dialogue in movies, TV news, sports programs, etc.,
can be made clearer using the “clear voice” function (p. 18).
Q3
Can I use a smartphone to operate the unit? Can I use a
smartphone to turn the unit on or off?
A3
Yes. The unit can be operated with a smartphone using the
free app, HOME THEATER CONTROLLER, installed on the
smartphone (p. 23).
In addition, the Bluetooth standby function can be used to
turn on the unit when a Bluetooth connection between the
unit and the smartphone is established, and to turn off the
unit when that connection is terminated (p. 23).
Q4
Can the brightness of the indicators be adjusted?
A4
Yes. Use the DIMMER key on the remote control (p. 19).
Q5
How can surround playback be enabled?
A5
Press the SURROUND key on the remote control (p. 18).
Q6
Can the subwoofer’s volume be adjusted?
A6
Yes. Use the SUBWOOFER (+/–) keys on the remote
control (p. 19).
10 En
Part names and functions
The unit (front panel/top panel)
7
6
7
8
23451
6
3 (mute) key
Mute the audio output. Press the key
again to unmute (p. 19).
4 / (volume +/-) keys
Adjust the volume (p. 19).
5 (power) key
Turn on or off the unit (p. 17).
HINT
The unit may automatically turn off when the
auto power standby function is enabled (p. 25).
6 Speakers
7 Dual built-in subwoofers
The built-in subwoofers are located in
the top part of the unit.
8 Remote control sensors
Receive infrared signals from the
remote control of the unit (p. 6).
1 Indicators
The indicators on the top panel flash or glow, to show the operation and setting status.
In this manual, illustrations of the nine in-line indicators are used for explanation as
necessary.
Example: When the DPL and SURROUND indicators glow, and the HDMI indicator
flashes
2 (input) key
Select an input source to be played back (p. 17).
: Off : Glows : Flashes
En 11
9 SUBWOOFER OUT jack
For connecting to an external subwoofer with an RCA mono cable
(p. 16).
0 ANALOG input jack
For connecting to an external device with a 3.5 mm stereo mini
plug cable (p. 15).
a TV input jack
For connecting to a TV with an optical digital audio cable (p. 14).
b HDMI OUT (ARC) jack
For connecting to an HDMI-compatible TV (p. 14).
c HDMI IN jack
For connecting an HDMI-compatible playback device such as a
BD/DVD player, a satellite and cable TV tuner, and a game
console (p. 14).
d AC IN jack
Connect the power cable of this unit (p. 16).
The unit (rear panel)
ANALOG
TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI
AC IN
9 0 a b c d
12 En
Installation
The unit can be installed on a TV stand or mounted on a wall.
Position the unit so that the keys are on the far side of the unit.
Refer to “How to mount the unit on the wall” (p. 13) for
instructions on mounting the unit on a wall so that the keys face
upwards.
Installing the unit on a TV stand, etc.
Cautions
Do not stack the unit and a BD player or other device directly on each other.
Doing so may cause a malfunction due to vibrations.
Do not hold the speaker portion (fabric parts) on the front and the top of the unit.
The unit contains non-magnetic shielding speakers. Do not place magnetically
sensitive items (hard disk drive, etc.) near the unit.
Depending on your installation environment, it may be better to connect the unit
and external devices before installing the unit.
Keys
Mounting the unit on a wall
Keys
En 13
How to mount the unit on the wall
1 Attach the mounting template on a wall and mark for the
screw holes.
2 Remove the mounting template from the wall, then install
commercially available screws (as illustrated below) at the
points marked on the wall.
3 Peel off the backing paper from the spacers and attach the
adhesive face to the unit as illustrated below.
4 Hang the unit on the screws.
Cautions
When mounting the unit on a wall, all installation work must be performed by a
qualified contractor or dealer. The customer must never attempt to perform this
installation work. Improper or inadequate installation could cause the unit to fall,
resulting in personal injury.
To prevent the unit from falling, attach it to a wall constructed of drywall
(plasterboard).
Make sure you use commercially available screws that can support the weight of
the installation (specified in Step 2 on the right). Using clamps other than
specified screws, such as short screws, nails, and two-sided tape, may cause
the unit to fall.
Fix the cables in place where they will not become loose. If your foot or hand
accidentally gets caught on a loose cable, the unit may fall.
Do not lean on the unit or apply excessive force to the top of the unit. Doing so
may cause the unit to fall.
Check that the unit is fixed securely after the installation. Yamaha will bear no
responsibility for any accidents caused by improper installations.
Tapes or thumbtacks
Mounting template (supplied)
Screw
holes
7 to 9 mm
(1/4" to 3/8")
13 to 15 mm (1/2" to 5/8")
4 mm (#8)
20 mm (3/4")
or more
Spacers
Mounting holes
on bottom of the
unit
14 En
Connections
a Connecting a TV and set-top box
For the cable connection, follow the procedure below.
ANALOG TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI AC IN
ANALOG TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI
AC IN
HDMI INPUT
123
OPTICAL
OUTPUT
HDMI
OUTPUT
12
1 HDMI cable (optional)
The digital audio/video signals from the set-
top box or BD/DVD player are input to this
unit.
2 HDMI cable (optional)
Digital video from the set-top box or BD/DVD
player is displayed on the TV.
NOTE
Use a 19-pin HDMI cable with the HDMI logo printed on it.
A cable with a maximum length of 5 m (16 ft) is
recommended to prevent degradation of signal quality.
For playback of 3D and 4K video content, use a high-
speed HDMI cable.
This unit supports HDCP version 2.2, a copy protection
technology. For playback of 4K video, connect the unit to
the HDMI input jack (one compatible with HDCP 2.2) on an
HDCP 2.2-compliant TV, and to the HDMI output jack on a
HDCP 2.2-compliant BD/DVD player.
Cable, satellite or
network set-top box, or
BD/DVD player
TV
1. Remove
the cap
2. Check the
direction of the
plug
Video signals
Use the optical digital audio cable
(supplied) when connecting the
unit to a TV that does not support
Audio Return Channel.
Audio signals
En 15
HINT
Audio Return Channel (ARC) supported TV
Connect an HDMI cable to the audio return channel supported jack (the jack with
“ARC” indicated) on TV.
Once the HDMI control function has been activated, video and audio content from
playback devices can be output from the TV even when this unit is off (HDMI signal
pass-through).
Enable the HDMI control function of this unit to activate the Audio Return Channel
(ARC) (p. 24).
b Connecting a game consol via the
analog jack
Connect an external device, such as a game console or TV that does
not have an optical digital audio output, to the ANALOG input jack of
the unit.
NOTE
When the ANALOG key on the remote control is pressed, the input source switches
to ANALOG, and sound from the device is output via this unit.
If volume can be adjusted on the device connected to the unit’s ANALOG input
jack, set that device's volume to the same level as that of other devices connected
to the unit’s HDMI jacks to prevent volume from being louder than expected.
What is Audio Return Channel (ARC)?
In order for the unit to play audio from a TV, the TV must usually be
connected to the unit via an audio cable as well as an HDMI cable.
If, however, the TV supports Audio Return Channel (ARC), TV
audio signals can be input to the unit via the HDMI cable that
outputs video signals from the unit to the TV.
ANALOG TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI AC IN
ANALOG
3.5 mm stereo mini plug cable
(optional)
Game console
16 En
c Using an external subwoofer
The unit has dual built-in subwoofers; however you can connect an
external subwoofer when you want to enhance low frequency sound.
Connect a subwoofer to the SUBWOOFER OUT jack of the unit.
Sound is output from both the built-in subwoofers and external
subwoofer.
NOTE
Use an external subwoofer with built-in amplifier.
d Connecting the power cable
After all connections are complete, connect the supplied power cable
to the AC IN jack on the unit and plug the power cable into an AC wall
outlet.
ANALOG TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI AC IN
SUBWOOFER OUT
RCA mono cable
(optional)
Mono input
ANALOG TV
OUT (ARC)
SUBWOOFER OUT
IN
HDMI AC IN
AC IN
To an AC wall outlet
En 17
Operations
Remote control signal transmitter
Transmits infrared signals.
(power) key
Turns on or off the unit.
Turned on
Turned off (Bluetooth standby function enabled, p. 23)
The indicator for the last input source selected glows.
1
Input keys
Select an input source to be played back.
HDMI .................Sound from a device connected to the HDMI IN
jack
TV......................TV audio or sound from a device connected to
the unit’s TV input jack
ANALOG ...........Sound from a device connected to the ANALOG
input jack
BLUETOOTH ....Sound from a Bluetooth connected device
The indicator for the selected input source glows.
(Example: when TV is selected)
HINT
To play sound from the device connected to the TV or to watch video from
the device, set the TV’s input source to the device.
For playback from a Bluetooth device, refer to page 21.
HDMI TV ANALOG BLUETOOTH
2
18 En
SURROUND
and
STEREO
keys
Switch between surround and stereo (2 channel) playback.
When surround playback is selected, you can enjoy a realistic
sound effect.
SURROUND........ Glows (surround playback)
STEREO.............. Off (stereo playback)
HINT
The DPL indicator glows when 2-channel
stereo signal is played in surround.
The TV Program, Movie, Music, Sports, or
Game surround mode can be selected
using the HOME THEATER
CONTROLLER app (p. 23) installed on a smartphone that supports the
Bluetooth function.
SURROUND
SURROUND
3
CLEAR VOICE key
Enable/disable the clear voice function.
When this function is enabled, human voices such as lines in
movies and TV shows, or news and sport commentary, are
played clearly.
BASS EXTENSION key
Enable/disable the bass extension function. When this
function is enabled, you can enjoy more powerful sound.
CLEAR
VOICE
CLEAR
VOICE
Glows (enabled) Off (disabled)
BASS
EXTENSION
BASS
EXTENSION
Glows (enabled) Off (disabled)
4
En 19
Decoder indicator
The unit supports the following audio signals. The color of the
indicator identifies the type of audio input signal.
BLUETOOTH STANDBY key
Hold down the key for more than 3 seconds to enable/disable the
Bluetooth standby function (p. 23).
5
SUBWOOFER (+/–) keys
Adjust the volume of the subwoofer.
MUTE key
Mute the audio output. Press the key again to unmute.
VOLUME (+/–) keys
Adjust the volume of the unit.
Volume down (–) Volume up (+)
Flash (on mute)
Volume down (–) Volume up (+)
6
DIMMER key
Change the brightness of the indicators. Each time the key is
pressed, the brightness of the indicators changes as follows.
Dim (default setting)OffBright
Indicators glow brightly just after operation and change to the
specified brightness after a few seconds.
7
Green (Dolby Digital), Red (DTS)
Off (PCM/analog signal/no input signal)
20 En
The HDMI control function (link function) coordinates operation of a TV and the unit so that the unit can be operated using the TV’s remote
control.
When a TV is connected to the unit with an HDMI cable (p. 14), the TV’s remote control can be used to perform the following operations.
Coordinated functions via the TV remote control
NOTE
If you are unable to operate the unit with your TV’s remote control, see page 24 for
more information.
HINT
Even if your TV supports the HDMI control function, some functions may not be
available. For details, refer to documentation supplied with your TV.
We suggest using devices (TV, BD/DVD player, etc.) from the same manufacturer.
Operating the unit by TV’s remote control (HDMI control)
Remote control of TV (Example)
2. Switch input sources
The unit’s input source switches accordingly when
the TV’s input source is switched.
Examples
– When a TV program is selected on the TV, the
unit’s audio input source is switched to the HDMI
OUT (ARC) jack using the ARC function or TV
jack.
– When a BD/DVD player is connected to the
HDMI IN jack on the unit, the unit’s input source
switches to HDMI when the BD/DVD player is
selected with the TV’s remote control.
The input source can be switched while the unit is
off.
1. Turn on/off
Both the TV and this unit turn on/off at the same
time.
3. Switch the audio output device
(TV or this unit (amplifier))
4. Adjust volume
This unit's volume can be adjusted when the
TV’s audio output is set to this unit (amplifier).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Yamaha YAS-106 El kitabı

Tip
El kitabı