Please read this manual carefully before operating your set and
retain it for future reference.
*MFL69361119*
www.lg.com
P/NO : MFL69361119(1602-REV00)
Printed in Korea
Safety and Reference
OWNER’S MANUAL
LED TV*
* LG LED TV applies LCD screen with LED
backlights.
2
ENGLISH
Safety instructions
Please read these safety precautions
carefully before using the product.
WARNING
Do not place the TV and/or remote control in
the following environments:
t A location exposed to direct sunlight
t An area with high humidity such as a
bathroom
t Near any heat source such as stoves and
other devices that produce heat
t Near kitchen counters or humidiers where
they can easily be exposed to steam or oil
t An area exposed to rain or wind
t Near containers of water such as vases
Otherwise, this may result in re, electric
shock, malfunction or product deformation.
Do not place the product where it might be
exposed to dust. This may cause a re hazard.
Mains Plug is the TV connecting/disconnecting
device to AC mains electric supply. This plug
must remain readily attached and operable
when TV is in use.
Do not touch the power plug with wet hands.
Additionally, if the cord pin is wet or covered
with dust, dry the power plug completely or
wipe dust o. You may be electrocuted due to
excess moisture.
Make sure to connect Mains cable to compliant
AC mains socket with Grounded earth pin.
(Except for devices which are not grounded
on earth.) Otherwise possibility you may be
electrocuted or injured.
Insert power cable plug completely into wall
socket otherwise if not secured completely into
socket, re ignition may break out.
Ensure the power cord does not come into
contact with hot objects such as a heater. This
may cause a re or an electric shock hazard.
Do not place a heavy object, or the product
itself, on power cables.
Otherwise, this may result in re or electric
shock.
ENGLISH
3
Bend antenna cable between inside and
outside building to prevent rain from owing
in. This may cause water damaged inside the
Product and could give an electric shock.
When mounting TV onto wall make sure to
neatly install and isolate cabling from rear of
TV as to not create possibility of electric shock /
re hazard.
Do not plug too many electrical devices into a
single multiple electrical outlet. Otherwise, this
may result in re due to over-heating.
Do not drop the product or let it fall over when
connecting external devices. Otherwise, this
may result in injury or damage to the product.
Keep the anti-moisture packing material or
vinyl packing out of the reach of children.
Anti-moisture material is harmful if
swallowed. If swallowed by mistake, force
the patient to vomit and visit the nearest
hospital. Additionally, vinyl packing can cause
suocation. Keep it out of the reach of children.
Do not let your children climb or cling onto the
TV.
Otherwise, the TV may fall over, which may
cause serious injury.
Dispose of used batteries carefully to ensure
that a small child does not consume them.
Please seek Doctor- Medical Attention
immediately if child consumes batteries.
Do not insert any metal objects/conductors
(like a metal chopstick/cutlery/screwdriver)
between power cable plug and input Wall
Socket while it is connected to the input
terminal on the wall. Additionally, do not touch
the power cable right after plugging into the
wall input terminal. You may be electrocuted.
(Depending on model)
Do not put or store inammable substances
near the product. There is a danger of
combustion/explosion or re due to careless
handling of the inammable substances.
4
ENGLISH
Do not drop metallic objects such as coins,
hair pins, chopsticks or wire into the product,
or inammable objects such as paper and
matches. Children must pay particular
attention. Electrical shock, re or injury can
occur. If a foreign object is dropped into the
product, unplug the power cord and contact the
service centre.
Do not spray water on the product or scrub
with an inammable substance (thinner or
benzene). Fire or electric shock accident can
occur.
Do not allow any impact, shock or any objects
to fall into the unit, and do not drop anything
onto the screen. You may be injured or the
product can be damaged.
Never touch this product or antenna during a
thunder or lighting storm.
You may be electrocuted.
Never touch the wall outlet when there
is leakage of gas, open the windows and
ventilate. It may cause a re or a burn by a
spark.
Do not disassemble, repair or modify the
product at your own discretion. Fire or electric
shock accident can occur.
Contact the service centre for check, calibration
or repair.
If any of the following occur, unplug the
product immediately and contact your local
service centre.
t The product has been impacted by shock
t The product has been damaged
t Foreign objects have entered the product
t The product produced smoke or a strange
smell
This may result in re or electric shock.
Unplug the TV from AC mains wall socket if you
do not intend to use the TV for a long period of
time. Accumulated dust can cause re hazard
and insulation deterioration can cause electric
leakage/shock/re.
ENGLISH
5
Apparatus shall not be exposed to dripping or
splashing and no objects lled with liquids,
such as vases, shall be placed on the apparatus.
Do not install this product on a wall if it could
be exposed to oil or oil mist. This may damage
the product and cause it to fall.
If water enters or comes into contact with TV,
AC adapter or power cord please disconnect
the power cord and contact service centre
immediately. Otherwise, this may result in
electric shock or re.
Only use an authorized AC adapter and power
cord approved by LG Electronics. Otherwise, this
may result in re, electric shock, malfunction or
product deformation.
Never Disassemble the AC adapter or power
cord. This may result in re or electric shock.
Be careful in handling the adapter to prevent
any external shocks to it. An external shock may
cause damage to the adapter.
CAUTION
Install the product where no radio wave occurs.
There should be enough distance between an
outside antenna and power lines to keep the
former from touching the latter even when the
antenna falls. This may cause an electric shock.
Do not install the product on places such as
unstable shelves or inclined surfaces. Also avoid
places where there is vibration or where the
product cannot be fully supported. Otherwise,
the product may fall or ip over, which may
cause injury or damage to the product.
6
ENGLISH
If you install the TV on a stand, you need to
take actions to prevent the product from
overturning. Otherwise, the product may fall
over, which may cause injury.
If you intend to mount the product to a wall,
attach VESA standard mounting interface
(optional parts) to the back of the product.
When you install the set to use the wall
mounting bracket (optional parts), x it
carefully so as not to drop.
Only use the attachments / accessories specied
by the manufacturer.
When installing the antenna, consult with a
qualied service technician. If not installed by
a qualied technician, this may create a re
hazard or an electric shock hazard.
We recommend that you maintain a distance
of at least 2 to 7 times the diagonal screen size
when watching TV. If you watch TV for a long
period of time, this may cause blurred vision.
Only use the specied type of battery. This could
cause damage to the remote control.
Do not mix new batteries with old batteries.
This may cause the batteries to overheat and
leak.
Batteries should not be exposed to excessive
heat. For example, keep away from direct
Sunlight, open replace and electric heaters.
Do not place non-rechargeable batteries in
charging device.
Make sure there are no objects between the
remote control and its sensor.
Signal from Remote Control can be interrupted
due to external/internal lighting eg Sunlight,
uorescent lighting. If this occurs turn o
lighting or darken viewing area.
ENGLISH
7
When connecting external devices such as
video game consoles, make sure the connecting
cables are long enough. Otherwise, the product
may fall over, which may cause injury or
damage the product.
Do not turn the product On/O by plugging-
in or unplugging the power plug to the wall
outlet. (Do not use the power plug for switch.)
It may cause mechanical failure or could give an
electric shock.
Please follow the installation instructions
below to prevent the product from overheating.
t The distance between the product and the
wall should be more than 10cm.
t Do not install the product in a place with
no ventilation (e.g., on a bookshelf or in a
cupboard).
t Do not install the product on a carpet or
cushion.
t Make sure the air vent is not blocked by a
tablecloth or curtain.
Otherwise, this may result in re.
Take care not to touch the ventilation openings
when watching the TV for long periods as the
ventilation openings may become hot. This
does not aect the operation or performance of
the product.
Periodically examine the cord of your appliance,
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with
an exact replacement part by an authorized
servicer.
Prevent dust collecting on the power plug pins
or outlet. This may cause a re hazard.
Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.
Do not press strongly upon the panel with a
hand or sharp object such as nail, pencil or pen,
or make a scratch on it, as it may causedamage
to screen.
8
ENGLISH
Avoid touching the screen or holding your
nger(s) against it for long periods of time.
Doing so may produce some temporary or
permanent distortion/damage to screen.
When cleaning the product and its components,
unplug the power rst and wipe it with a soft
cloth. Applying excessive force may cause
scratches or discolouration. Do not spray with
water or wipe with a wet cloth. Never use glass
cleaner, car or industrial shiner, abrasives or
wax, benzene, alcohol etc., which can damage
the product and its panel. Otherwise, this may
result in re, electric shock or product damage
(deformation, corrosion or breakage).
As long as this unit is connected to the AC wall
outlet, it is not disconnected from the AC power
source even if you turn o this unit by SWITCH.
When unplugging the cable, grab the plug and
unplug it, by pulling at the plug.
Don’t pull at the cord to unplug the power
cord from the power board, as this could be
hazardous.
When moving the product, make sure you turn
the power o rst. Then, unplug the power
cables, antenna cables and all connecting
cables.
The TV set or power cord may be damaged,
which may create a re hazard or cause electric
shock.
When moving or unpacking the product,
work in pairs because the product is heavy.
Otherwise, this may result in injury.
Refer all servicing to qualied service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
If the product feels cold to the touch, there may
be a small “icker” when it is turned on. This is
normal, there is nothing wrong with product.
ENGLISH
9
The panel is a high technology display product
with resolution of two million to six million
pixels. You may see tiny black dots and/or
brightly coloured dots (red, blue or green) at
a size of 1ppm on the panel. This does not
indicate a malfunction and does not aect the
performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
You may nd dierent brightness and color
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
Displaying a still image for a prolonged period
of time may cause image sticking. Avoid
displaying a xed image on the TV screen for a
long period of time.
Generated Sound
“Cracking” noise: A cracking noise that
occurs when watching or turning o the TV
is generated by plastic thermal contraction
due to tempera-ture and humidity. This
noise is common for products where thermal
deformation is required. Electrical circuit
humming/panel buzzing: A low level noise is
generated from a high-speed switching circuit,
which supplies a large amount of current to
operate a product. It varies depending on the
product.
This generated sound does not aect the
performance and reliability of the product.
Do not use high voltage electrical goods near
the TV (e.g. electric mosquito-swatter). This
may result in product malfunction.
10
ENGLISH
Viewing 3D imaging (Only
3D models)
WARNING
Viewing Environment
t Viewing Time
- When watching 3D contents, take 5 to
15 minute breaks every hour. Viewing 3D
contents for a long period of time may
cause headache, dizziness, fatigue or eye
strain.
Those that have a
photosensitive seizure or
chronic illness
t Some users may experience a seizure or
other abnormal symptoms when they are
exposed to a ashing light or particular
pattern from 3D contents.
t Do not watch 3D videos if you feel nausea,
are pregnant and/ or have a chronic illness
such as epilepsy, cardiac disorder, or blood
pressure disease, etc.
t 3D Contents are not recommended to those
who suer from stereo blindness or stereo
anomaly. Double images or discomfort in
viewing may be experienced.
t If you have strabismus (cross-eyed),
amblyopia (weak eyesight) or astigmatism,
you may have trouble sensing depth and
easily feel fatigue due to double images. It
is advised to take frequent breaks than the
average adult.
t If your eyesight varies between your right
and left eye, correct your eyesight prior to
watching 3D contents.
Symptoms which require
discontinuation or
refraining from watching 3D
contents
t Do not watch 3D contents when you feel
fatigue from lack of sleep, overwork or
drinking.
t When these symptoms are experienced,
stop using/watching 3D contents and get
enough rest until the symptom subsides.
- Consult your doctor when the symptoms
persist. Symptoms may include headache,
eyeball pain, dizziness, nausea, palpitation,
blurriness, discomfort, double image,
visual inconvenience or fatigue.
CAUTION
Viewing Environment
t Viewing Distance
- Maintain a distance of at least twice the
screen diagonal length when watching 3D
contents. If you feel discomfort in viewing
3D contents, move further away from the
TV.
Viewing Age
t Infants/Children
- Usage/ Viewing 3D contents for children
under the age of 6 are prohibited.
- Children under the age of 10 may
overreact and become overly excited
because their vision is in development
(for example: trying to touch the screen or
trying to jump into it). Special monitoring
and extra attention is required for children
watching 3D contents.
ENGLISH
11
- Children have greater binocular disparity
of 3D presentations than adults because
the distance between the eyes is shorter
than that of adults. Therefore they
will perceive more stereoscopic depth
compared to adults for the same 3D image.
t Teenagers
- Teenagers under the age of 19 may react
with sensitivity due to stimulation from
light in 3D contents. Advise them to refrain
from watching 3D contents for a long time
when they are tired.
t Elderly
- The elderly may perceive less 3D eect
compared to the young. Do not sit closer to
the TV than the recommended distance.
Cautions when using the 3D
glasses
t Make sure to use LG 3D glasses. Otherwise,
you may not be able to view 3D videos
properly.
t Do not use 3D glasses instead of your
normal glasses, sunglasses or protective
goggles.
t Using modied 3D glasses may cause eye
strain or image distortion.
t Do not keep your 3D glasses in extremely
high or low temperatures. It will cause
deformation.
t The 3D glasses are fragile and are easily
scratched. Always use a soft, clean piece
of cloth when wiping the lenses. Do not
scratch the lenses of the 3D glasses with
sharp objects or clean/wipe them with
chemicals.
Preparing
NOTE
t If the TV is turned on for the rst time
after it was shipped from the factory,
initialization of the TV may take a few
minutes.
t Image shown may dier from your TV.
t Your TV’s OSD (On Screen Display) may dier
slightly from that shown in this manual.
t The available menus and options may dier
from the input source or product model that
you are using.
t New features may be added to this TV in the
future.
t The items supplied with your product may
vary depending on the model.
t Product specications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
t For an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports USB 2.0 if the
USB cable or USB memory stick does not t
into your TV’s USB port.
A
B
A
B
*A
<
=
10 mm
*B
<
=
18 mm
t Use a certied cable with the HDMI logo
attached.
12
ENGLISH
t If you do not use a certied HDMI cable, the
screen may not display or a connection error
may occur. (Recommended HDMI Cable
Types)
- High-Speed HDMI
®
/
TM
cable (3 m or less)
- High-Speed HDMI
®
/
TM
cable with Ethernet
(3 m or less)
t How to use the ferrite core (Depending on
model)
- Use the ferrite core to reduce the
electromagnetic interference in the power
cord. Wind the power cord on the ferrite
core once.
[Wall side]
[TV side]
10 cm (+ / -2 cm)
t Antenna Isolator Installation Guide
(Depending on model)
- Use this to install TV in a place where there
is a voltage dierence between TV Set and
GND of antenna signal.
»If there is a voltage difference between
TV Set and GND of antenna signal, the
antenna contact might be heated and
excessive heat might cause an accident.
- You can improve the safety when watching
TV by eciently removing power voltage
from TV antenna. It is recommended to
mount the isolator to the wall. If it cannot
be mounted to the wall, mount it on the
TV. Avoid disconnecting the antenna
Isolator after installation.
- Before starting, be sure that the TV
antenna is connected.
ANTENNA/
CABLE IN
Wall
Cable /
Antenna
or
Isolator
1. Connect to TV.
2. Connect to Set-Top box.
- Connect one end of the isolator to cable/
antenna jack and the other to TV set or
set-top box.
- “Equipment connected to the protective
earthing of the building installation
through the mains connection or through
other equipment with a connection
to protective earthing - and to a cable
distribution system using coaxial cable,
may in some circumstances create a re
hazard. Connection to a cable distribution
system has therefore to be provided
through a device providing electrical
isolation below a certain frequency range
(galvanic isolator, see EN 60728-11)”
- When applying the RF Isolator, a slight loss
of signal sensitivity can occur.
ENGLISH
13
CAUTION
t Do not use any unapproved items to ensure
the safety and product life span.
t Any damage or injuries caused by using
unapproved items are not covered by the
warranty.
t Some models have a thin lm attached on
to the screen and this must not be removed.
t When attaching the stand to the TV
set, place the screen facing down on a
cushioned table or at surface to protect
the screen from scratches.
t Make sure that the screws are inserted
correctly and fastened securely. (If they are
not fastened securely enough, the TV may
tilt forward after being installed.) Do not
use too much force and over tighten the
screws; otherwise screw may be damaged
and not tighten correctly.
t Make sure to wring any excess water or
cleaner from the cloth.
t Do not spray water or cleaner directly onto
the TV screen.
t Make sure to spray just enough of water or
cleaner onto a dry cloth to wipe the screen.
t When cleaning the product, be careful not
to allow any liquid or foreign objects to
enter the gap between the upper, left or
right side of the panel and the guide panel.
(Depending on model)
Separate purchase
Separate purchase items can be changed or
modied for quality improvement without any
notication. Contact your dealer to buy these
items. These devices only work with certain
models.
The model name or design may be changed
depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
(Depending on model)
AG-F***
Cinema 3D Glasses
AN-MR650
Magic Remote
AN-VC550
Smart camera
AG-F***DP
Dual Play Glasses
Lifting and moving
the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
t It is recommended to move the TV in
the box or packing material that the TV
originally came in.
t Before moving or lifting the TV, disconnect
the power cord and all cables.
t When holding the TV, the screen should
face away from you to avoid damage.
14
ENGLISH
t Hold the top and bottom of the TV
frame rmly. Make sure not to hold the
transparent part, speaker, or speaker grill
area.
t When transporting a large TV, there should
be at least 2 people.
t When transporting the TV by hand, hold the
TV as shown in the following illustration.
t When transporting the TV, do not expose
the TV to jolts or excessive vibration.
t When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
t Do not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
t When handling the TV, be careful not to
damage the protruding buttons.
CAUTION
t Avoid touching the screen at all times, as
this may result in damage to the screen.
t Do not move the TV by holding the cable
holders, as the cable holders may break,
and injuries and damage to the TV may
occur.
Using the button
(Depending on model)
You can simply operate the TV functions,
pressing or moving the button.
NOTE
t 43/49UH61, 43/49UH62 series does not
have a Joystick button but has only a power
On/O button.
<A type>
Joystick Button
Dome Button
or
<B type>
Joystick Button
ENGLISH
15
Basic functions
Power On (Press)
Power O (Press
and hold)
1
Volume Control
Programmes
Control
1 All running apps will close, and any
recording in progress will stop.
Adjusting the menu
When the TV is turned on, press the button
one time. You can adjust the Menu items
pressing or moving the buttons.
Turns the power o.
Clears on-screen displays and returns
to TV viewing.
Changes the input source.
Accesses the settings menu.
Mounting on a
table
1 Lift and tilt the TV into its upright position on
a table.
t Leave a 10 cm (minimum) space from the
wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
10 cm
2 Connect the power cord to a wall outlet.
CAUTION
t Do not place the TV near or on sources
of heat, as this may result in re or other
damage.
Securing the TV to a wall
(This feature is not available for all models.)
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
t If there are bolts inserted at the eye-bolts
position, remove the bolts rst.
2 Mount the wall brackets with the bolts to
the wall.
Match the location of the wall bracket and
the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the at surface.
CAUTION
t Make sure that children do not climb on or
hang on the TV.
NOTE
t Use a platform or cabinet that is strong and
large enough to support the TV securely.
t Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
16
ENGLISH
Mounting on a wall
Attach an optional wall mount bracket at the
rear of the TV carefully and install the wall
mount bracket on a solid wall perpendicular
to the oor. When you attach the TV to other
building materials, please contact qualied
personnel. LG recommends that wall mounting
be performed by a qualied professional
installer. We recommend the use of LG’s wall
mount bracket. LG’s wall mount bracket is
easy to move with cables connected. When
you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is
adequately secured to the wall with enough
space to allow connectivity to external devices.
It is advised to connect all the cables before
installing xed wall mounts.
10 cm
10 cm
10 cm
10 cm
Make sure to use screws and wall mount
bracket that meet the VESA standard. Standard
dimensions for the wall mount kits are
described in the following table.
Separate purchase(Wall
mounting bracket)
Model
43UH61**
40/43UH62**
40UH63**
43UH65**
43UH66**
40/43UH67**
43UH74**
43UH75**
49/55UH61**
49/55UH62**
50UH63**
49/55UH65**
49/55UH66**
49/50/55UH67**
49/55UH74**
49/55UH75**
49/55UH77**
49/55UH79**
49/55UH80**
49/55UH84**
49/55UH85**
VESA (A x
B) (mm)
200 x 200 300 x 300
Standard
screw
M6 M6
Number
of screws
4 4
Wall
mount
bracket
LSW240B
MSW240
LSW350B
MSW240
ENGLISH
17
Model
60/65UH61**
60/65UH62**
58UH63**
60/65UH65**
60/65UH66**
58/60/65UH67**
60UH74**
60/65UH75**
60/65UH77**
60/65UH80**
60UH84**
60/65UH85**
70UH63**
75UH65**
70UH67**
70UH70**
75UH77**
75UH78**
75UH80**
75UH85**
79/86UH95**
VESA (A x
B) (mm)
300 x 300 600 x 400
Standard
screw
M6 M8
Number
of screws
4 4
Wall
mount
bracket
LSW350B LSW640B
Model 55/65UH95**
VESA (A x
B) (mm)
300 x 200
Standard
screw
M6
Number
of screws
4
Wall
mount
bracket
OTW420B
A
B
CAUTION
t Remove the stand before installing the TV
on a wall mount by performing the stand
attachment in reverse.
NOTE
t When installing the wall mounting bracket,
use the adhesive label or protective cover
provided. The adhesive label or protective
cover will protect the opening from
accumulating dust and dirt. (Only when the
label or cover is provided)
Provided item
Adhesive label
Provided item
Adhesive label
Provided item
Protective cover
18
ENGLISH
t When installing the wall mounting bracket,
it is recommended to cover the stand hole
using tape, in order to prevent the inux of
dust and insects. (Depending on model)
Stand hole
t When attaching a wall mounting bracket
to the TV, insert the wall mount spacers
into the TV wall mount holes to adjust the
vertical angle of the TV. (Only when the
item of the following form is provided)
Provided
Item
Wall Mount
Spacer
t Depending on the shape of the stand, use
a at tool to remove the stand cover as
illustrated below. (e.g., a at screwdriver)
(Only when the item of the following form
is provided)
Flat tool
Connections
(notications)
Connect various external devices to the TV and
switch input modes to select an external device.
For more information of external device’s
connection, refer to the manual provided with
each device.
Available external devices are: HD receivers, DVD
players, VCRs, audio systems, USB storage devices,
PC, gaming devices, and other external devices.
NOTE
t The external device connection may dier
from the model.
t Connect external devices to the TV
regardless of the order of the TV port.
t If you record a TV program on a DVD
recorder or VCR, make sure to connect the
TV signal input cable to the TV through a
DVD recorder or VCR. For more information
of recording, refer to the manual provided
with the connected device.
t Refer to the external equipment’s manual
for operating instructions.
t If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
t In PC mode, there may be noise associated
with the resolution, vertical pattern,
contrast or brightness. If noise is present,
change the PC output to another resolution,
change the refresh rate to another rate or
adjust the brightness and contrast on the
PICTURE menu until the picture is clear.
ENGLISH
19
t In PC mode, some resolution settings
may not work properly depending on the
graphics card.
t If ULTRA HD content is played on your PC,
video or audio may become disrupted
intermittently depending on your PC’s
performance. (Depending on model)
Antenna connection
Connect the TV to a wall antenna socket with
an RF cable (75 Ω).
t Use a signal splitter to use more than 2 TVs.
t If the image quality is poor, install a signal
amplier properly to improve the image
quality.
t If the image quality is poor with an
antenna connected, try to realign the
antenna in the correct direction.
t An antenna cable and converter are not
supplied.
t Supported DTV Audio: MPEG, Dolby Digital,
Dolby Digital Plus, HE-AAC
t For a location that is not supported with
ULTRA HD broadcasting, this TV cannot
receive ULTRA HD broadcasts directly.
(Depending on model)
Satellite dish connection
(Only satellite models)
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
CI module connection
(Depending on model)
View the encrypted (pay) services in digital TV mode.
t Check if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
t If the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
USB connection
Some USB Hubs may not work. If a USB device
connected using a USB Hub is not detected,
connect it to the USB port on the TV directly.
Other connections
Connect your TV to external devices. For the
best picture and audio quality, connect the
external device and the TV with the HDMI cable.
Some separate cable is not provided.
t
General HDMI
ULTRA HD Deep Colour
- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2,
4:2:0)
- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also
supports ULTRA HD Deep Colour, your picture
may be clearer. However, if the device doesn’t
support it, it may not work properly. In that
case, connect the device to a dierent HDMI
port or change the TV’s HDMI ULTRA HD
Deep Colour setting to Off.
(This feature is available on certain models which
are supported ULTRA HD Deep Colour only.)
20
ENGLISH
NOTE
t Supported HDMI Audio format :
Dolby Digital (32 kHz, 44.1 kHz, 48 kHz),
DTS (44.1 kHz, 48 kHz),
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)
(Depending on model)
Remote control
The descriptions in this manual are based on the
buttons on the remote control. Please read this
manual carefully and use the TV correctly.
To replace batteries, open the battery cover,
replace batteries (1.5 V AAA) matching the and
ends to the label inside the compartment, and
close the battery cover. To remove the batteries,
perform the installation actions in reverse.
Make sure to point the remote control toward
the remote control sensor on the TV.
(Depending on model)
A
B
2
1
3
4
5
A
(POWER) Turns the TV on or o.
Selects Radio, TV and DTV
programme.
(INPUT) Changes the input source.
(Q. Settings) Accesses the Quick Settings.
1
,
2
By zooming in on the
selected area, you can view it in full screen.
(Depending on model)
1
,
2
Views the information of the
current programme and screen. (Depending
on model)
1
(SEARCH) Search for content such as
TV programmes, movies and other videos, or
perform a web search by entering text in the
search bar. (Depending on model)
2
Recalls your preferred subtitle in
digital mode. (Depending on model)
Number buttons Enters numbers.
Accesses the saved programmes list.
(Space) Opens an empty space on the
screen keyboard.
3
Shows programme guide.
(Depending on model)
3
Returns to the previously viewed
programme. (Depending on model)
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
