Yamaha PDS-150 El kitabı

Yamaha
Marka
Yamaha
Modeli
PDS-150
Tip
El kitabı
–
PEDESTAL
Manuel d’installation
Avant d'essayer d'essembler ces accessoires, veuillez lire
ces instructions complètement.
Veuillez garder ce manuel pour une rèfèrence future.
Instrucciones de instalación
Antes de instalar estos accesorios, lea cuidadosamente
estas instrucciones.
Guarde estas instrucciones para futuras referencias.
Installation Instructions
Before attempting to assemble these accessories, please
read these instructions completely.
Please retain this book for future reference.
TQZW260
2
Precautions with regard to setting up
WARNING
Installation work should only be carried out by a qualified technician.
• If the pedestal is not installed correctly, the wide plasma display may fall over and personal injury may result.
CAUTION
Do not use any displays other than those given in the catalogue.
Do not climb up onto the pedestal or use it as a step. (Young children should be made
particularly aware of this caution.)
• If the unit falls over or becomes damaged through misuse, injury may result.
Do not use the pedestal if it becomes warped or physically damaged.
• If you use the pedestal whilst it is physically damaged, personal injury may result. Contact your
nearest YAMAHA Dealer immediately.
Set up on a stable, level surface.
• If this is not done, the unit may fall over and become damaged, and personal injury may result.
Do not use in places with high humidity.
• Long-term usage in such conditions can cause warping or deformation. This can lead to loss of
strength, and the unit may fall over and become damaged, and personal injury may result.
During setting-up, make sure that all screws are securely tightened.
• If sufficient care is not taken to ensure screws are properly tightened during assembly, the
pedestal will not be strong enough to support the wide plasma display, and it might fall over and
become damaged, and personal injury may result.
Use the accessory fall-prevention brackets to secure the wide plasma display.
• If the unit is knocked or children climb onto the pedestal with the wide plasma display installed,
the wide plasma display may fall over and personal injury may result.
Two people are required to install and remove the display.
• If two people are not present, the display may be dropped, and personal injury may result.
Notes on handling
1) If the unit is placed in direct sunlight or next to a stove, the light and heat may cause discoloration or deformation.
2) Cleaning
Wipe the unit with a dry cloth. If the unit is particularly dirty, clean it using a cloth soaked with water to which a
small amount of neutral detergent has been added, and then wipe with a dry cloth.
Do not use products such as solvents, thinner or household wax for cleaning, as they can damage the surface
coating.
(If using a chemically-treated cloth, follow the instructions supplied with the cloth.)
3) Do not attach sticky tape or labels, as they can make the surface of the pedestal dirty.
3
Assembling the pedestal / Setting-up
Assembly screw
...........................4
Assembly screw
(Black screw)....4
Pole ...................2 Base ..................1
Base
PolePole
For 50˝ display(Outside)
Insert the poles into the left and right holes in the
underside of the base so that they fit securely as
shown in the illustration above.
2. Securing the poles
Base
Pole
Pole
Front
Use the assembly screws to secure the poles
firmly to the bottom of the base.
Accessories for pedestal assembly
Assembling the pedestal
The numbers (such as ) in the explanatory text indicate part numbers in the table of accessories.
Setting-up
1. Installing the poles
1. Setting up the display unit
Display unit
Cloth or similar
Spread a clean cloth or similar material over a level
floor or base, and place the display unit on it face
down.
2. Securing the display unit
* Carry out work on a
horizontal and level
surface.
Display unit
Pole
Rear
Pedestal
Front
Nameplate
Use the assembly screws (Black screw) to
fasten securely.
Lift the display unit above the pedestal base, with
the back of the display unit on the same side as
the Nameplate. Then align the holes in the display
unit with the poles of the pedestal and lower the
display unit into place.
Assemble the poles correctly by referring to the illustrations below.
4
If securing to the base If securing to a wall
Front
Front
Black
screw
Black
screw
Band
Base
Wood Worktop
Band
Wood screw
Wood screw
Screw into the
middle of the
back edge of a
wood worktop.
Clamp
• Preparation
• Securing method
Black screw
Clamp
Band .................2
Wood screw......2 Clamp ...............4Black screw ......4
Fall-prevention brackets
* Use strong wire or chain which
is commercially available to
secure the wide plasma
display to a solid area of the
wall or a pillar.
Preventing the wide plasma display from falling over
Dimensions
685 (26
31
/32)
270 (10
5
/8)
105.4
(4
5
/32)
164.6
(6
15
/32)
727 (28
5
/8) 62.5 (2
29
/64)
21 (
53
/64)
16 (
5
/8)
184.5 (7
17
/64)
151 (5
15
/16)
106 (4
11
/64)
Units : mm (inches)
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Japan M0602-0
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Yamaha PDS-150 El kitabı

Yamaha
Marka
Yamaha
Modeli
PDS-150
Tip
El kitabı
PDF''yi indir
rapor

diğer dillerde

İlgili makaleler

Diğer belgeler