Yamaha CRW-3200UX El kitabı
- Kategori
- Optik disk sürücüleri
- Tip
- El kitabı
Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
(DECLARATION OF CONFORMITY PROCEDURE)
Responsible Party: Yamaha Electronics Corporation, USA.
Address: 6660 Orangethorpe Avenue
Buena Park, CA 90620
Telephone: 714-522-9105
Fax: 714-670-0108
Type of Equipment: CD Recordable/Rewritable Drive
Model Name: CRW3200UX
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.
Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.
Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class
“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product
in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses
radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause
interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product is found to be the source of interference, which can be determined
by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change
the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this
type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.
6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.
CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.
AVOID EXPOSURE TO BEAM.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.
VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI
NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.
VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG
WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL
EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.
COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.
CLASS 1 LASER PRODUCT
LASER KLASSE 1 PRODUKT
LUOKAN 1 LASERLAITE
KLASS 1 LASER APPARAT
PRODUIT LASER DE CLASSE 1
DANGER - VISIBLE AND / OR INVISIBLE LASER
RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE
TO BEAM.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
Laser Product Class: Class 1
Laser Diode Properties
Wavelength: 780 – 787 nm
Pulse Durations and Max. Output
at the lens of the Laser Pickup Unit
Read Mode: 0.85 mW (Continuous)
Write Mode: Max. 48 mW
(for 212 ns, Min. Cycle 57.9 ns)
ACHTUNG
Halten Sie sich beim Bedienen und Einstellen der
Bedienungselemente sowie bei der Bedienungsabfolge
an die Anleitung, da sonst gefährliche Strahlen austreten
können.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereuses.
PRECAUCION
El usar los controles o ajustar o realizar procedimientos
diferentes a los especificados aquí resultará en
peligrosas exposiciones a la radiación.
VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA
OLET ALTTINA NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.
Laserprodukt-Klasse: Klasse 1
Eigenschaften der Laserdiode
Wellenlänge: 780 – 787 nm
Impulsdauer und max. Ausgang an der Linse der
Laser-Abtasteinheit
Lesemodus: 0,85 mW (kontinuierlich)
Schreibmodus: Max. 48 mW
(für 212 ns, Zyklusmin. 57,9 ns)
Classe du produit laser: Classe 1
Caractéristiques de la diode laser
Longueur d’onde: 780 – 787 nm
Durée des impulsions et sortie maximum depuis
la lentille du bloc capteur optique
Mode de lecture: 0,85 mW (continue)
Mode de gravure: max. 48 mW
(pour 212 ns, cycle min. 57,9 ns)
Clase de producto láser: Clase 1
Propiedades del diodo láser
Longitud de onda: 780 – 787 nm
Duración del pulso y potencia de salida máxima
en el objetivo de la unidad captora láser
Modo de lectura: 0,85 mW (continua)
Modo de escritura: máx. 48 mW
(para 212 ns, ciclo mínimo 57,9 ns)
i
OWNER’S MANUAL
English
ii
SAFETY PRECAUTIONS
PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY
TO PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.
These precautions explain how to use the device properly and safely, thereby
preventing injury to yourself and others. This section has been sub-divided into a
WARNING section and a CAUTION section, according to the likelihood and nature
of any potential injuries or damage inflicted. They relate to your personal safety,
and also help you prevent the risk of damage to the device. Please read these
sections carefully prior to proceeding.
WARNING
Always follow these basic precautions to avoid short-circuit, damage, fire, or
other hazards, and to avoid serious injury or fatal accident from electrical shock.
● Do not attempt to open or disassemble the device to avoid the risk of electrical
shock, fire, or malfunction.
● Do not look directly at the laser source to avoid the risk of eye damage or
blindness.
● Do not insert fingers or foreign objects into the device to avoid the risk of
electrical shock, fire, malfunction, or personal injury.
● Do not expose the device to high humidity or place liquid containers such as a
flower vase on the device to avoid the risk of electrical shock, fire, or
malfunction.
● Do not expose the device to temperature outside the range 5 – 35 °C (41 – 95 °F)
to avoid the risk of fire, deformation of the device panel, or malfunction.
● Do not expose the device to dusty place to avoid the risk of fire or malfunction.
● Always follow the owner’s manual to set up or connect the devices properly to
avoid the risk of electrical shock, fire, malfunction, or personal injury.
● If unusual smells, sounds or smoke come from the device, or if foreign objects
such as liquid get into the device, turn off and unplug the computer immediately
to avoid the risk of electrical shock, fire, or malfunction. Contact the store of
purchase or your nearest Yamaha dealer (listed at the back of this manual).
iii
● Be sure that the computer is electrically grounded to avoid the risk of electrical
shock.
● Prior to cleaning the drive, always unplug the computer or do not handle the plug
with wet hands to avoid the risk of electrical shock.
● Use the included AC adapter to avoid the risk of fire or malfunction.
● Clean the AC power plug regularly to avoid the risk of fire due to insulation failure
such as humidity.
● Do not unplug the AC adapter by pulling the cable, and do not place objects on
the cable to avoid the risk of electrical shock, fire, or malfunction.
● Plug in the AC adapter fully to avoid the risk of electrical shock or fire.
● Do not connect many devices to an electrical outlet. Maintain the rated power of
the outlet to avoid the risk of fire due to overheating.
CAUTION
Always follow these basic precautions to avoid physical injury to yourself or
others, and damage to the device or other property.
● Always unplug the computer if it will not be used for a prolonged period or if
there is a possibility of lightning, to avoid the risk of electrical shock, fire, or
short-circuit.
● Do not use the device near other electrical appliances such as televisions, radios,
or speakers to avoid the risk of interferences between each other.
● Do not place the device unstably to avoid the risk of malfunction or personal
injury by its falling down.
● Do not place the device with a possibility of excessive vibration to avoid the risk
of damage to written data or malfunction.
● Place the device horizontally to avoid the risk of damage to written data.
● Prior to transporting the device, remove the disc from the disc tray to avoid the
risk of damage to written data.
iv
● Use soft, dry cloths to wipe the device. Do not use benzene, paint
thinner, detergents, or chemically treated wiped cloths, and do not place
vinyl, plastic, or rubber objects on the device to avoid the risk of
malfunction or damage to surface of the device.
● Do not rest your weight on or place heavy objects on the device, and do
not apply excessive force to the buttons, switches, or connectors to
avoid the risk of damage to the device or personal injury.
● Be careful not to short-circuit the AC power plug with metal objects to
avoid the risk of malfunction.
● Do not wrap the power cable around the AC adapter to avoid the risk of
breaking the wire or malfunction.
● Do not listen to audio with headphones at high volume for prolonged
period to avoid auditory disorder.
● Prior to turning on the computer, always minimize the volume to avoid
auditory disorder by a sudden burst of sound at high volume.
● Do not place the device near magnets or anything magnetized such as a
display to avoid the risk of interferences between each other.
● Have the device serviced regularly to avoid internal dust buildup that can
cause malfunction, damage or fire. For service information and service
charges, contact the store of purchase or your nearest Yamaha dealer
(listed at the back of this manual).
v
WARRANTY
YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR
AS A RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE
MANUAL THAT COMES WITH THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY
DATA CAUSED AS A RESULT OF USING THIS PRODUCT.
Precautions for Transportation
Transporting the device unfixed may damage its internal mechanism or circuits.
• Remove the disc from the disc tray of the device.
• Put the device in the original box.
Prior to use, check that the complete accessories are included. (Refer to the original box.)
• ©2001 YAMAHA CORPORATION. All Rights Reserved.
• This document may not, in whole or in part, be copied, photocopied, reproduced,
translated, transmitted, or reduced to any electronic medium of machine readable form
without prior consent in writing from Yamaha.
• Windows is a registered trademark of Microsoft Corporation.
• SafeBurn™ is a trademark of Yamaha Corporation.
• All other trademarks are the property of their respective companies.
™ and ® marks are not specified in context.
vi
Table of Contents
Features of the CRW3200UX Drive ............................................... 1
Names and Functions of Parts..................................................... 3
Front Panel.............................................................................................. 3
Rear Panel ............................................................................................... 4
Precautions on Use ................................................................. 5
Handling Discs........................................................................................ 5
Copyright ................................................................................................ 5
Disclaimer of Indemnity ......................................................................... 5
Compatible Discs.................................................................................... 6
System Requirements ............................................................................. 8
Preparing the CRW3200UX Drive................................................11
Serial Number ....................................................................................... 11
1 Connect the CRW3200UX Drive ..................................................... 12
2 Install the Device Drivers ................................................................. 16
3 Check Recognition of the CRW3200UX Drive ............................... 16
4 Install CD Writing Software............................................................. 18
Disconnecting the CRW3200UX Drive...........................................19
Loading/Ejecting a Disc ...........................................................20
Troubleshooting ....................................................................22
Firmware ............................................................................29
CRW3200UX Drive Specifications ...............................................30
Technical Notes ....................................................................34
Buffer Underrun Protection Function ................................................... 34
Writing Methods ................................................................................... 35
For details about how to install and use the CD writing software, refer to the
documentation that comes with it.
• The information contained in this manual is subject to change without prior notice.
• Reproduction of this manual, either in part or in full, is expressly forbidden.
1
Features of the CRW3200UX Drive
High speed writing/reading
The CRW3200UX drive supports up to 24X-speed writing for CD-R discs, and
up to 10X-speed writing/rewriting for CD-RW discs. In addition, the drive
supports data reading and digital audio data extraction at up to 40X speed.
Tip
• The Partial CAV method permits 24X-speed writing for CD-R discs.
• The CLV method and the 4X – 10X Full CAV method permit 10X-speed writing/
rewriting for CD-RW discs.
USB interface (USB 2.0)
The CRW3200UX drive uses USB 2.0 that provides high-speed data transfer
capability (max. speed 480 Mbps/sec.). The transfer speed is about 40 times
faster than the USB 1.1.
In addition, the CRW3200UX drive supports the hotplug function that enables
you to connect/disconnect the drive while computer is turned on.
SafeBurn™ (Enhanced stability writing technology)
The generous 8 MB buffer memory provides sufficient data storage to enable
stable disc writing at high speeds. Even if data transfer from the computer is
interrupted, the Buffer Underrun Protection function is activated to save CD-R
discs from a writing error. (P. 34)
“Optimum Write Speed Control” adjusts the writing speed to the optimum rate
for every CD-R disc automatically. You can set the maximum writing speed
with your CD writing software.
• Optimum Write Speed Control can be activated when the maximum writing
speed is set at 12X or more.
• The minimum writing speed to be automatically selected is 8X. Manually set the
optimum writing speed if a writing speed supported by a disc is less than 8X.
High fidelity digital audio
The CRW3200UX drive supports extraction of digital audio data at up to 40X
speed using CD writing software, as well as recording digital audio with high
fidelity even at 24X-speed writing.
Note
Features of the CRW3200UX Drive
2
Audio Master Quality Recording (High quality audio writing mode)
Audio Master Quality Recording enables you to create high quality audio CDs.
This mode is available for CD-R discs with a capacity of 650 MB and 700 MB.
(P. 36)
Audio CDs that are created with Audio Master Quality Recording may not be played
back on certain audio recorders and CD-R/RW drives.
CD-MRW (CD Mount Rainier ReWriting)
CD-MRW is a new standard of packet writing. Compared to the ordinary packet
writing, CD-MRW provides many useful functions such as background
formatting. (P. 36)
Note
3
Names and Functions of Parts
➀
Disc tray
Holds the disc. It is opened or closed by
pressing the eject button. (P. 20)
➁
Manual eject hole
Forcibly opens the disc tray when the
tray cannot be opened by pressing the
eject button. (P. 21)
➂
Eject button
Press to open or close the disc tray.
(P. 20)
➃
Headphone jack
Connects headphones or external
speakers to the drive; has stereo mini-
jack specifications.
➄
Headphone volume dial
Controls the volume of the headphones.
The volume increases as the dial is turned
to the right.
➅
LED
Indicates the operational status of the
CRW3200UX drive by its colors and
blinking patterns.
Lights or blinks blue
• Lights: Standby (with disc)
• Blinks: Opening/Closing disc tray, or
reading disc information (TOC)
• Blinks rapidly: Playback audio
• Blinks irregularly: Reading data
Lights or blinks purple
• Lights: Standby (no disc) or the disc
tray is open
• Blinks: Accessing for writing or test
writing
• Blinks rapidly: Writing
Blinks orange
• Malfunction
Front Panel
➅
➁
➃➄
➀
➂
5
Precautions on Use
To avoid trouble, such as writing errors, loss of recorded data, and malfunction
of the drive, take the following precautions when handling discs.
• Do not place discs in a hot or damp place or where they will be exposed to
direct sunlight.
• Do not touch the disc surface. Hold the disc by the edge when handling it.
• Remove dust and dirt from the disc surface. Use an air spray to remove dust.
The disc surface may be scratched if strongly wiped with a dry cloth.
• Do not stick labels to the disc surface or write anything on it except where
designated.
• Do not clean discs with chemicals or detergents.
• Do not bend or drop discs.
It is prohibited by law to duplicate copyright material for non-personal use
without the prior consent of the copyright holder. When copying material with
your CD-R/RW drive, take due care not to infringe the copyright.
• Yamaha assumes no liability for the loss of any profits incurred as a result of
the loss or corruption of data written on a CD-R or CD-RW, for any loss or
damage caused by or arising out of extraordinary circumstances (including
circumstances that Yamaha has foreseen or could foresee), nor for any
damages incurred or claimed by a third party.
• After handling important data, make a comparison between the original and
the copied data (to confirm that the data has been copied properly).
• In no event shall Yamaha be liable for any damage to discs due to a Buffer
Underrun Error (P. 34) or for any other reason, or the inability to use
distributed discs with your drive.
• Yamaha assumes no liability for the inability to write/playback discs because
of their format.
Handling Discs
Copyright
Disclaimer of Indemnity
Precautions on Use
6
Discs that can be written on
The CRW3200UX drive can write on the following discs.
For the latest information about discs previously checked for compatibility with
the drive, refer to the following website.
YAMAHA CD-R/RW Drive website
URL: http://www.yamaha.co.jp/english/product/computer/
Compatible Discs
CD-R discs
• The CRW3200UX drive can write at 1X, 2X, 4X, 8X, 12X, 16X or 24X speed.
• CD-R discs can be played back on a CD-ROM drive or a CD player.
• 24X-speed writing is enabled with Partial CAV method. (P. 7)
• Check the writing speeds your disc supports prior to writing.
CD-RW discs
• The CRW3200UX drive can write/rewrite at 2X or 4X speed.
• CD-RW discs can be read/played back on a device (e.g. CD-ROM drive)
that supports “CD-RW” discs.
Some discs support only 2X speed.
High Speed CD-RW discs
• The CRW3200UX drive can write/rewrite at 4X, 8X or 10X speed.
• High Speed CD-RW discs can be read/played back on a CD-RW drive
that bears the High Speed CD-RW logo or a device (e.g. CD-ROM drive)
that supports “CD-RW” discs.
• When using the packet writing method (P. 36) for writing/rewriting onto High
Speed CD-RW discs, you can select the 4X – 10X Full CAV method. For more
information refer to the documentation that comes with your CD writing
software. (Your CD writing software must support the Full CAV method, as
does the CD Writing software that comes with the CRW3200UX drive.)
• The Full CAV method is recommended when opening and editing a file on a
CD-RW disc with an application software.
• In order to write, erase, read or play back High Speed CD-RW discs, use a CD-
R/RW drive that bears the High Speed CD-RW logo. When using a CD-ROM
drive to read/play back High Speed CD-RW discs, use a drive that supports
CD-RW discs.
If these discs are used with a CD-R/RW drive not bearing the High Speed CD-
RW logo, the discs may not be recognized, resulting in a computer not
operating properly or other malfunctions occurring.
Refer to the YAMAHA website below prior to attempting to read/play back
these discs on a YAMAHA CD-R/RW drive not bearing the High Speed CD-
RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
Note
Note
Note
7
Partial CAV (Constant Angular Velocity)
The CLV (Constant Linear Velocity) method is generally used to write data on a
CD-R disc. In writing using the CLV method, the disc rotation speed is adjusted to
keep the data writing speed (data transfer rate) constant on all parts of the disc.
In contrast, the CAV (Constant Angular Velocity) method exercises control so as to
keep the disc rotation speed constant. Since the CAV method makes it possible to
substantially increase the maximum data transfer rate without straining of the drive,
it is adopted today for most CD-ROM drives.
CD formats define the constant linear density of written data so that the amount of
written data per disc rotation will increase as the writing point moves from the inner
track to the outer track.
With the CAV method, therefore, data is transferred at a higher rate when it is
written on the outer tracks of the disc. To achieve 24X-speed writing, the
CRW3200UX drive employs the Partial CAV method, which is a combination of the
CAV method for inner tracks and the CLV method for outer tracks.
The Partial CAV method controls the disc rotation speed so that the CRW3200UX
drive starts writing at 18X speed on inner tracks, increasing the speed to 24X as the
read/write head moves outward and holds the speed at 24X on outer tracks.
Tip
The CRW3200UX drive supports 8 cm discs.
Use only circular discs. Do not use any irregular shaped discs such as heart-shaped
or star-shaped discs to avoid the risk of malfunction.
Note
Precautions on Use
8
The CRW3200UX drive is designed to operate in the following computer
environment. If your computer does not meet these requirements, the
CRW3200UX drive may not operate or write at the maximum speed.
Computer (PC/AT compatible)
• CPU: Pentium II-class or higher, 300 MHz or faster
•RAM: 64 MB or more
64 MB or more is required (128 MB is recommended) for Windows 2000
Professional, while 128 MB or more is required (256 MB is recommended)
for Windows XP.
•CD-ROM drive
• A CD-ROM drive other than the CRW3200UX drive is required to install the
device drivers.
• The CRW3200UX drive cannot be used to boot the computer or to set up an
operating system.
• Hard drive space
Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as
a working area on the hard drive. When writing data on a CD-R/RW disc after
creating an image file, there must be enough free space on the hard drive to
store the image file in addition to the working area (a total of up to 900 MB).
However, hard drive space for image files is not required when directly
writing onto a CD-R/RW disc from a hard drive or CD-ROM using the
CRW3200UX drive (on-the-fly writing).
Image file
You can collect the data files to be written on a CD-R/RW disc into a single image
file.
The image file is useful for writing the same data onto multiple discs. For details,
refer to the documentation that comes with the CD writing software.
System Requirements
Note
9
• USB port (USB 2.0 compatible)
A USB port is required to connect the CRW3200UX drive to the computer.
The CRW3200UX drive needs to be connected to the USB port on the
computer. The drive connected to the computer via a USB hub may not
operate properly.
To fully utilize the CRW3200UX drive, a USB 2.0 compatible interface card
and EHCI (Enhanced Host Controller Interface) compliant driver are also
required.
If a computer has a USB port with USB 1.1 specifications, Yamaha
recommends that a USB 2.0 compatible interface card be installed in the
computer.
For the latest information about USB 2.0 interface cards supporting the
CRW3200UX drive, refer to the following websites.
YAMAHA CD-R/RW Drive website
URL: http://www.yamaha.co.jp/english/product/computer/
Europe
URL: http://www.yamaha-it.de/
For information about where to find an EHCI compliant driver for the USB
interface card or information about operating systems supporting the card, refer to
the card manufacturer’s website or contact the manufacturer.
Connecting the drive to a USB port with USB 1.1 specifications
When the CRW3200UX drive is connected to a USB 1.1-compliant port on the
computer, the drive operates with USB 1.1 specifications.
For secure data writing, activate the Buffer Underrun protection and set the
writing speed with the writing software to 8X.
The data reading speed is up to 6X.
Note
Continued on next page
Precautions on Use
10
USB cable
The USB standard for maximum length of cable between devices is five meters.
Operating system
Windows 98 Second Edition, Windows Me, Windows 2000 Professional, or
Windows XP.
CD writing software
The CRW3200UX drive requires CD writing software to write onto a CD-R/
RW disc. Use the CD writing software that supports the CRW3200UX drive.
For details about installing and using the CD writing software, refer to the
documentation that comes with the CD writing software.
CRW3200UX
Maximum length of cable
between devices : 5.0 m
11
Preparing the CRW3200UX Drive
The serial number is printed on the label on the bottom of your CRW3200UX
drive. When you have a question about the drive or need user support services,
the serial number is required.
Please write the serial number down in the space below. It may be difficult to
check the serial number after setting up the drive or for any other reason.
Serial Number
Serial Number
Serial number
(10 characters: 3 letters +
7 numbers)
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
Sayfa yükleniyor...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
Yamaha CRW-3200UX El kitabı
- Kategori
- Optik disk sürücüleri
- Tip
- El kitabı
- Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
diğer dillerde
- français: Yamaha CRW-3200UX Le manuel du propriétaire
- italiano: Yamaha CRW-3200UX Manuale del proprietario
- svenska: Yamaha CRW-3200UX Bruksanvisning
- Deutsch: Yamaha CRW-3200UX Bedienungsanleitung
- English: Yamaha CRW-3200UX Owner's manual
- dansk: Yamaha CRW-3200UX Brugervejledning
- suomi: Yamaha CRW-3200UX Omistajan opas
- Nederlands: Yamaha CRW-3200UX de handleiding
- română: Yamaha CRW-3200UX Manualul proprietarului
İlgili makaleler
-
Yamaha CRW3200IX Series Kullanım kılavuzu
-
-
-
-
-
-
-
-
-