Dolmar AS4030 El kitabı

Marka: Dolmar

Model: AS4030

Kategori: Motorlu testereler

Tip: El kitabı

AS4030

AS4035

Cordless Chain Saw INSTRUCTION MANUAL 8

Tronçonneuse sans Fil MANUEL D’INSTRUCTIONS 20

Akku-Kettensäge BETRIEBSANLEITUNG 33

Motosega a batteria ISTRUZIONI PER L’USO 46

Accukettingzaag GEBRUIKSAANWIJZING 60

Electrosierra Inalámbrica

MANUAL DE

INSTRUCCIONES

Motosserra a Bateria MANUAL DE INSTRUÇÕES 87

Akku-kædesav BRUGSANVISNING 100

Φορητό αλυσοπρίονο ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ 112

Akülü Ağaç Kesme KULLANMA KILAVUZU 127

Fig.1

345

1011

1920

Fig.2

Fig.3

Fig.4

Fig.5

Fig.6

Fig.7

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

Fig.14

Fig.15

Fig.16

Fig.17

Fig.18

Fig.19

Fig.20

Fig.21

Fig.22

Fig.23

Fig.24

Fig.25

Fig.26

Fig.27

Fig.28

Fig.29

1/5

Fig.30

Fig.31

Fig.32

Fig.33

Fig.34

Fig.35

Fig.36

8 ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: AS4030 AS4035

Overall length (without guide bar) 270 mm

Rated voltage D.C. 36 V

Net weight *1 4.2 kg

*2 4.7 - 4.9 kg 4.8 - 5.0 kg

Standard guide bar length 300 mm 350 mm

Recommended guide bar

length

with 90PX 250 - 400 mm

with 91PX 250 - 400 mm

Applicable saw chain type

(refer to the table below)

90PX

91PX

Standard sprocket Number of teeth 6

Pitch 3/8″

Chain speed 0 - 20 m/s

(0 - 1,200 m/min)

Chain oil tank volume 200 cm

•

Due to our continuing program of research and development, the specications herein are subject to change without notice.

• Specications may differ from country to country.

*1:

Weight, with largest battery cartridge and empty oil tank, and without guide bar and chain, according to EN ISO 11681-2.

*2: The lightest and heaviest combination of weight, according to EPTA-Procedure 01/2014. The weight may differ

depending on the attachment(s), including the battery cartridge.

Applicable battery cartridge

BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B

• Some of the battery cartridges listed above may not be available depending on your region of residence.

WARNING:

Only use the battery cartridges listed above. Use of any other battery cartridges may cause injury and/or re.

Saw chain, guide bar, and sprocket combination

Saw chain type 90PX

Number of drive links 46 52

Guide bar Guide bar length 300 mm 350 mm

Cutting length 294 mm 350 mm

Pitch 3/8″

Gauge 1.1 mm

Type Sprocket nose bar

Sprocket Number of teeth 6

Pitch 3/8″

Saw chain type 91PX

Number of drive links 46 52

Guide bar Guide bar length 300 mm 350 mm

Cutting length 294 mm 350 mm

Pitch 3/8″

Gauge 1.3 mm

Type Sprocket nose bar

Sprocket Number of teeth 6

Pitch 3/8″

WARNING: Use appropriate combination of the guide bar and saw chain. Otherwise personal injury may

result.

9 ENGLISH

Symbols

The followings show the symbols used for the equip-

ment. Be sure that you understand their meaning before

use.

Read instruction manual.

Wear safety glasses.

Wear ear protection.

Wear a helmet, goggles and ear protection.

Use appropriate protection for foot-leg and

hand-arm.

This saw is to be used by properly trained

operators only.

Do not expose to moisture.

Maximum permissible cut length

Always use two hands when operating the

chain saw.

Beware of chain saw kickback and avoid

contact with bar tip.

Direction of chain travel

Saw chain oil adjustment

Ni-MH

Li-ion

Only for EU countries

Do not dispose of electric equipment or

battery pack together with household waste

material!

In observance of the European Directives,

on Waste Electric and Electronic

Equipment and Batteries and Accumulators

and Waste Batteries and Accumulators

and their implementation in accordance

with national laws, electric equipment and

batteries and battery pack(s) that have

reached the end of their life must be col-

lected separately and returned to an envi-

ronmentally compatible recycling facility.

Intended use

The tool is intended for cutting branches and pruning

trees. It is also suitable for tree service.

Noise

The typical A-weighted noise level determined accord-

ing to EN ISO 11681-2:

Model AS4030

Sound pressure level (L

) : 89 dB(A)

Sound power level (L

) : 103 dB (A)

Uncertainty (K) : 3 dB(A)

Model AS4035

Sound pressure level (L

) : 89 dB(A)

Sound power level (L

) : 103 dB (A)

Uncertainty (K) : 3 dB(A)

NOTE:

The declared noise emission value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE:

The declared noise emission value(s) may also

be used in a preliminary assessment of exposure.

WARNING: Wear ear protection.

WARNING: The noise emission during actual

use of the power tool can differ from the declared

value(s) depending on the ways in which the

tool is used especially what kind of workpiece is

processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

off and when it is running idle in addition to the

trigger time).

Vibration

The vibration total value (tri-axial vector sum) deter-

mined according to EN ISO 11681-2:

Model AS4030

Work mode: cutting wood

Vibration emission (a

h,W

) : 3.2 m/s

Uncertainty (K) : 1.5 m/s

Model AS4035

Work mode: cutting wood

Vibration emission (a

h,W

) : 3.2 m/s

Uncertainty (K) : 1.5 m/s

NOTE: The declared vibration total value(s) has been

measured in accordance with a standard test method

and may be used for comparing one tool with another.

NOTE: The declared vibration total value(s) may also

be used in a preliminary assessment of exposure.

WARNING: The vibration emission during

actual use of the power tool can differ from the

declared value(s) depending on the ways in which

the tool is used especially what kind of workpiece

is processed.

WARNING: Be sure to identify safety mea-

sures to protect the operator that are based on an

estimation of exposure in the actual conditions of

use (taking account of all parts of the operating

cycle such as the times when the tool is switched

off and when it is running idle in addition to the

trigger time).

10 ENGLISH

EC Declaration of Conformity

For European countries only

The EC declaration of conformity is included as Annex A

to this instruction manual.

SAFETY WARNINGS

General power tool safety warnings

WARNING: Read all safety warnings, instruc-

tions, illustrations and specications provided

with this power tool. Failure to follow all instructions

listed below may result in electric shock, re and/or

serious injury.

Save all warnings and instruc-

tions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Cordless Chain saw safety warnings

1. Keep all parts of the body away from the saw

chain when the chain saw is operating. Before

you start the chain saw, make sure the saw

chain is not contacting anything. A moment of

inattention while operating chain saws may cause

entanglement of your clothing or body with the

saw chain.

2. Always hold the chain saw with your right

hand on the top handle and your left hand on

the front handle. Holding the chain saw with a

reversed hand conguration increases the risk of

personal injury and should never be done.

Hold the power tool by insulated gripping sur-

faces only, because the saw chain may contact

hidden wiring. Saw chains contacting a "live" wire

may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

4. Wear safety glasses and hearing protection.

Further protective equipment for head, hands,

legs and feet is recommended. Adequate protec-

tive clothing will reduce personal injury by ying

debris or accidental contact with the saw chain.

5. Always keep proper footing.

When cutting a limb that is under tension be alert

for spring back. When the tension in the wood bres

is released the spring loaded limb may strike the

operator and/or throw the chain saw out of control.

7. Use extreme caution when cutting brush and

saplings. The slender material may catch the saw

chain and be whipped toward you or pull you off

balance.

8. Carry the chain saw by the front handle with

the chain saw switched off and away from your

body. When transporting or storing the chain

saw always t the guide bar cover. Proper

handling of the chain saw will reduce the likelihood

of accidental contact with the moving saw chain.

9. Follow instructions for lubricating, chain ten-

sioning and changing accessories. Improperly

tensioned or lubricated chain may either break or

increase the chance for kickback.

10. Keep handles dry, clean, and free from oil and

grease. Greasy, oily handles are slippery causing

loss of control.

11. Cut wood only. Do not use chain saw for pur-

poses not intended. For example: do not use

chain saw for cutting plastic, masonry or non-

wood building materials. Use of the chain saw for

operations different than intended could result in a

hazardous situation.

12. Causes and operator prevention of kickback:

Kickback may occur when the nose or tip of the guide

bar touches an object, or when the wood closes in

and pinches the saw chain in the cut. Tip contact in

some cases may cause a sudden reverse reaction,

kicking the guide bar up and back towards the opera-

tor. Pinching the saw chain along the top of the guide

bar may push the guide bar rapidly back towards

the operator. Either of these reactions may cause

you to lose control of the saw which could result in

serious personal injury. Do not rely exclusively upon

the safety devices built into your saw. As a chain saw

user, you should take several steps to keep your

cutting jobs free from accident or injury.

Kickback is the result of tool misuse and/or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below:

• Maintain a rm grip, with thumbs and ngers

encircling the chain saw handles, with both

hands on the saw and position your body

and arm to allow you to resist kickback

forces. Kickback forces can be controlled by

the operator, if proper precautions are taken.

Do not let go of the chain saw.

► Fig.1

• Do not overreach and do not cut above

shoulder height. This helps prevent unin-

tended tip contact and enables better control

of the chain saw in unexpected situations.

• Only use replacement bars and chains spec-

ied by the manufacturer. Incorrect replace-

ment bars and chains may cause chain

breakage and/or kickback.

• Follow the manufacturer’s sharpening and

maintenance instructions for the saw chain.

Decreasing the depth gauge height can lead

to increased kickback.

13. Before starting work, check that the chain

saw is in proper working order and that its

condition complies with the safety regulations.

Check in particular that:

• The chain brake is working properly;

• The run-down brake is working properly;

•

The bar and the sprocket cover are tted correctly;

• The chain has been sharpened and ten-

sioned in accordance with the regulations.

14. Do not start the chain saw with the chain cover

being installed on it. Starting the chain saw with

the chain cover being installed on it may cause

the chain cover to thrown out forward resulting in

personal injury and damage to objects around the

operator.

11 ENGLISH

Additional Safety Warnings:

When using the tool with battery adapter, be care-

ful not to trip over the cord during operation.

2. When using the tool with battery adapter, keep

the cord away from obstacles such as a work-

piece and branches during operation. The cord

caught by obstacles may cause serious injury.

Top handle chainsaw specic safety

warnings

1. This chain saw is designed especially for tree

care and surgery. The chain saw is intended

to be used by properly trained persons only.

Observe all instructions, procedures and rec-

ommendations from the relevant professional

organization. Otherwise fatal accidents may

occur. It is recommend that always using a

rising platform (cherry picker, lift) for sawing

in trees. Rappelling techniques are extremely

dangerous and require special training. The

operators must be trained to become familiar

with safety equipment usage and climbing

techniques. Always use the appropriate belts,

ropes and carabiners when working in trees.

Always use restraining equipment for both the

operator and the saw.

2. Perform cleaning and maintenance before

storage in accordance with the instruction

manual.

Ensure safe positioning of the chain saw during

car transportation to avoid fuel or chain oil leak-

age, damage to the tool and personal injury.

4. Regularly check the functionality of chain

brake.

5. Do not ll the chain oil near re. Never smoke

when you ll the chain oil.

6. National regulation may restrict the use of the

chain saw.

7. If the equipment gets heavy impact or fall,

check the condition before continuing work.

Check the controls and safety devices for mal-

function. If there is any damage or doubt, ask

our authorized service center for the inspec-

tion and repair.

8. Always activate the chain brake before starting

the chain saw.

9. Hold the saw rmly in place to avoid skating

(skid movement) or bouncing of the saw when

starting a cut.

10. At the end of the cut, be careful to keep your

balance due to the “drop”.

11. Take into account the direction and speed of

the wind. Avoid sawdust and chain oil mist.

Protective equipment

1. In order to avoid head, eye, hand or foot

injuries as well as to protect your hearing the

following protective equipment must be used

during operation of the chain saw:

— The kind of clothing should be appropriate,

i. e. it should be tight-tting but not be a

hindrance. Do not wear jewelry or clothing

which could become entangled with bushes

or shrubs. If you have long hair, always wear

a hairnet!

— It is necessary to wear a protective helmet

whenever working with the chain saw. The

protective helmet is to be checked in regu-

lar intervals for damage and is to be replaced

after 5 years at the latest. Use only approved

protective helmets.

— The face shield of the protective helmet (or

the goggles) protects against sawdust and

wood chips. During operation of the chain

saw always wear a goggle or a face shield to

prevent eye injuries.

— Wear adequate noise protection equip-

ment (ear muffs, ear plugs, etc.)

— The protective jacket consists of 22 layers

of nylon and protects the operator against

cuts. It is always to be worn when working

from elevated platforms (cherry pickers,

lifts), from platforms mounted on ladders or

when climbing with ropes.

— The protective brace and bib overall is

made of a nylon fabric with 22 layers and

protects against cuts. We strongly recom-

mend its use.

— Protective gloves made of thick leather are

part of the prescribed equipment and must

always be worn during operation of the chain

saw.

— During operation of the chain saw safety

shoes or safety boots tted with anti skid

sole, steel toe caps and protection for the

leg must always to be worn. Safety shoes

equipped with a protective layer provide

protection against cuts and ensure a secure

footing. For working in trees the safety boots

must be suitable for climbing techniques.

Vibration

1. Individuals with poor circulation who are exposed

to excessive vibration may experience injury to

blood vessels or the nervous system. Vibration

may cause the following symptoms to occur in the

ngers, hands or wrists: “Falling asleep” (numb-

ness), tingling, pain, stabbing sensation, alteration

of skin colour or of the skin. If any of these symp-

toms occur, see a physician! To reduce the risk

of “white nger disease”, keep your hands warm

during operation and well maintain the equipment

and accessories.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity

with product (gained from repeated use) replace

strict adherence to safety rules for the subject

product. MISUSE or failure to follow the safety

rules stated in this instruction manual may cause

serious personal injury.

12 ENGLISH

Important safety instructions for

battery cartridge

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them

out with clear water and seek medical atten-

tion right away. It may result in loss of your

eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any con-

ductive material.

(2) Avoid storing battery cartridge in a con-

tainer with other metal objects such as

nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.

A battery short can cause a large current

ow, overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a re.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries are subject

to the Dangerous Goods Legislation require-

ments.

For commercial transports e.g. by third parties,

forwarding agents, special requirement on pack-

aging and labeling must be observed.

For preparation of the item being shipped, consult-

ing an expert for hazardous material is required.

Please also observe possibly more detailed

national regulations.

Tape or mask off open contacts and pack up the

battery in such a manner that it cannot move

around in the packaging.

11. Follow your local regulations relating to dis-

posal of battery.

12. Use the batteries only with the products spec-

ied by Makita/Dolmar. Installing the batteries to

non-compliant products may result in a re, exces-

sive heat, explosion, or leak of electrolyte.

SAVE THESE INSTRUCTIONS.

CAUTION: Only use genuine Makita/Dolmar

batteries. Use of non-genuine Makita/Dolmar batter-

ies, or batteries that have been altered, may result in

the battery bursting causing res, personal injury and

damage. It will also void the Makita/Dolmar warranty

for the Makita/Dolmar tool and charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. Charge the battery cartridge if you do not use

it for a long period (more than six months).

PARTS DESCRIPTION

► Fig.2

1 Battery indicator 2 Check button 3 Switch trigger

4 Top handle 5 Lock-off lever 6 Front hand guard

7 Guide bar 8 Saw chain 9 Chain catcher

10 Retaining nut 11 Chain adjusting screw 12 Battery cartridge

13 Main power lamp 14 Mode indicator 15 Main power switch

16 Cap 17 Adjusting screw (for oil pump) 18 Carabiner

19 Front handle 20 Oil tank cap 21 Spike bumper

22 Guide bar cover - - - -

13 ENGLISH

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before adjusting or checking function on the tool.

Installing or removing battery

cartridge

CAUTION: Always switch off the tool before

installing or removing of the battery cartridge.

CAUTION: Hold the tool and the battery car-

tridge rmly when installing or removing battery

cartridge. Failure to hold the tool and the battery

cartridge rmly may cause them to slip off your hands

and result in damage to the tool and battery cartridge

and a personal injury.

► Fig.3: 1. Red indicator 2. Button 3. Battery cartridge

To remove the battery cartridge, slide it from the tool

while sliding the button on the front of the cartridge.

To install the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Insert it all the way until it locks in place

with a little click. If you can see the red indicator on the

upper side of the button, it is not locked completely.

CAUTION: Always install the battery cartridge

fully until the red indicator cannot be seen. If not,

it may accidentally fall out of the tool, causing injury to

you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

Indicating the remaining battery capacity

► Fig.4: 1. Battery indicator 2. Check button

Press the check button to indicate the remaining battery

capacities. The battery indicators correspond to each

battery.

Battery indicator status Remaining

battery

capacity

Off

Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

► Fig.5: 1. Indicator lamps 2. Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may differ slightly

from the actual capacity.

Tool / battery protection system

The tool is equipped with a tool/battery protection sys-

tem. This system automatically cuts off power to the

motor to extend tool and battery life. The tool will auto-

matically stop during operation if the tool or battery is

placed under one of the following conditions:

Overload protection

When the battery is operated in a manner that causes

it to draw an abnormally high current, the tool automati-

cally stops and the main power lamp blinks in green. In

this situation, turn the tool off and stop the application

that caused the tool to become overloaded. Then turn

the tool on to restart.

Overheat protection

When the tool or battery is overheated, the tool stops

automatically and the main power lamp lights up in red.

In this case, let the tool and battery cool before turning

the tool on again.

NOTE: In high temperature environment, the over-

heat protection likely to work and the tool stops

automatically.

Overdischarge protection

When the battery capacity is not enough, the tool stops

automatically and the main power lamp blinks in red. In

this case, remove the battery from the tool and charge

the battery.

14 ENGLISH

Main power switch

WARNING: Always turn off the main power

switch when not in use.

To turn on the tool, press the main power switch until

the main power lamp lights up in green. To turn off,

press the main power switch again.

► Fig.6: 1. Main power lamp 2. Mode indicator

3. Main power switch

NOTE: The main power lamp blinks in green if the

switch trigger is pulled under unoperatable conditions.

The lamp blinks in one of the following conditions.

• When you turn on the main power switch while

holding down the lock-off lever and the switch

trigger.

• When you pull the switch trigger while the chain

brake is applied.

• When you release the chain brake while holding

down the lock-off lever and pulling the switch

trigger.

NOTE: This tool employs the auto power-off function.

To avoid unintentional start up, the main power switch

will automatically shut down when the switch trigger

is not pulled for a certain period after the main power

switch is turned on.

You can use the tool in the Torque Boost mode for

cutting thick branches or hard branches. To use the tool

in the Torque Boost mode, when the tool is turned off,

press the main power switch for a few seconds until the

mode indicator lights up in green.

NOTE: You can use the tool in the Torque Boost

mode up to 60 seconds. Depending on the usage

conditions, this mode shifts to the normal mode in

less than 60 seconds.

NOTE: If the mode indicator blinks in green when

you press the main power switch for a few seconds,

the Torque Boost mode is not available. In this case,

follow the steps below.

• The Torque Boost mode is not available right

after the cutting operation. Wait for more than 10

seconds, and then press the main power switch

for a few seconds again.

• If you use the Torque Boost mode several times,

the use of the Torque Boost mode is restricted to

protect the battery. If the Torque Boost mode is

not available after waiting for more than 10 sec-

onds, replace the battery cartridge with a fully

charged one, or recharge the battery cartridge.

NOTE: If the main power lamp lights up in red or

blinks in red or green, refer to the instructions for tool/

battery protection system.

Switch action

WARNING: For your safety, this tool is

equipped with lock-off lever which prevents the

tool from unintended starting. NEVER use the tool

if it runs when you simply pull the switch trigger

without pressing the lock-off lever. Return the

tool to our authorized service center for proper

repairs BEFORE further usage.

WARNING: NEVER tape down or defeat pur-

pose and function of lock-off lever.

CAUTION: Before installing the battery car-

tridge into the tool, always check to see that the

switch trigger actuates properly and returns to

the "OFF" position when released.

NOTICE: Do not pull the switch trigger hard with-

out pressing the lock-off lever. This can cause

switch breakage.

To prevent the switch trigger from being accidentally

pulled, a lock-off lever is provided. To start the tool,

depress the lock-off lever and pull the switch trigger.

The tool speed increases by increasing pressure on the

switch trigger. Release the switch trigger to stop.

► Fig.7: 1. Switch trigger 2. Lock-off lever

Checking the chain brake

CAUTION: Hold the chain saw with both

hands when switching it on. Hold the top handle

with your right hand, the front handle with your

left. The bar and the chain must not be in contact

with any object.

CAUTION: Should the saw chain not stop

immediately when this test is performed, the

saw may not be used under any circumstances.

Consult our authorized service center.

1. Press the lock-off lever, then pull the switch trig-

ger. The saw chain starts immediately.

2. Push the front hand guard forwards with the back

of your hand. Make sure that the chain saw comes to an

immediate standstill.

► Fig.8: 1. Front hand guard 2. Unlocked position

3. Locked position

Checking the run-down brake

CAUTION: If the saw chain does not stop

within two seconds in this test, stop using the

chain saw and consult our authorized service

center.

Run the chain saw then release the switch trigger completely.

The saw chain must come to a standstill within two seconds.

Adjusting the chain lubrication

You can adjust the oil pump feed rate with the adjusting screw

using the universal wrench. The amount of oil can be adjusted

in 3 steps. Open the cap to adjust the adjusting screw.

► Fig.9: 1. Cap 2. Adjusting screw

15 ENGLISH

Carabiner (rope attachment point)

You can hang the tool by attaching the rope to the cara-

biner. Pull up the carabiner, and then tie it with the rope.

► Fig.10: 1. Carabiner

Spike bumper

The tool is equipped with the spike bumper as stan-

dard. For replacement of the spike bumper, ask Makita/

Dolmar Authorized Service Centers.

When you perform the cutting operation, engage the

spike bumper with the trunk and use it as a lever.

Electronic function

The tool is equipped with the electronic functions for

easy operation.

• Constant speed control

The speed control function provides the constant

rotation speed regardless of load conditions.

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: Do not touch the saw chain with

bare hands. Always wear gloves when handling

the saw chain.

Removing or installing saw chain

CAUTION: The saw chain and the guide bar

are still hot just after the operation. Let them cool

down enough before carrying out any work on

the tool.

CAUTION: Carry out the procedure of install-

ing or removing saw chain in a clean place free

from sawdust and the like.

To remove the saw chain, perform the following steps:

Release the chain brake by pulling the front hand guard.

2. Loosen the chain adjusting screw, then the retain-

ing nut.

► Fig.11: 1. Chain adjusting screw 2. Retaining nut

3. Remove the sprocket cover then remove the saw

chain and guide bar from the chain saw body.

To install the saw chain, perform the following steps:

1. Check the direction of the saw chain. Match the

direction of the saw chain with that of the mark on the

chain saw body.

2. Fit one end of the saw chain on the top of the

guide bar.

3. Fit the other end of the saw chain around the

sprocket, then attach the guide bar to the chain saw

body, aligning the hole on the guide bar with the pin on

the chain saw body.

► Fig.12: 1. Sprocket 2. Hole

4. Insert the protrusion and the pin on the sprocket

cover to the chain saw body, and then close the cover

so that the bolt and pin on the chain saw body meet

their counterparts on the cover.

► Fig.13: 1. Protrusion 2. Sprocket cover 3. Bolt

4. Pin

5. Tighten the retaining nut to secure the sprocket

cover, then loosen it a bit for tension adjustment.

► Fig.14: 1. Retaining nut

Adjusting saw chain tension

CAUTION: Do not tighten the saw chain too

much. Excessively high tension of saw chain may

cause breakage of saw chain and wear of the guide

bar.

CAUTION: A chain which is too loose can

jump off the bar and it may cause an injury

accident.

The saw chain may become loose after many hours

of use. From time to time check the saw chain tension

before use.

Release the chain brake by pulling the front hand guard.

2. Loosen the retaining nut a bit to loosen the

sprocket cover lightly.

► Fig.15: 1. Retaining nut

3. Lift up the guide bar tip slightly and adjust the

chain tension. Turn the chain adjusting screw clockwise

to tighten, turn it counterclockwise to loosen.

Tighten the saw chain until the lower side of the saw

chain ts in the guide bar rail as illustrated.

► Fig.16: 1. Guide bar 2. Saw chain 3. Chain adjust-

ing screw

4. Keep holding the guide bar lightly and tighten the

sprocket cover.

Make sure that the saw chain does not loose at the

lower side.

Tighten the retaining nut to secure the sprocket cover.

► Fig.17: 1. Retaining nut

OPERATION

Lubrication

Saw chain is automatically lubricated when the tool is in

operation. Check the amount of remaining oil in the oil

tank periodically through the oil inspection window.

To rell the tank, lay the chain saw on its side, then

push the oil tank cap, and then remove the oil tank

cap. The proper amount of oil is 200 ml. After relling

the tank, make sure that the oil tank cap is tightened

securely.

► Fig.18: 1. Oil tank cap 2. Oil inspection window

After relling, hold the chain saw away from the

tree. Start it and wait until lubrication on saw chain is

adequate.

► Fig.19

16 ENGLISH

NOTICE: When lling the chain oil for the rst

time, or relling the tank after it has been com-

pletely emptied, add oil up to the bottom edge of

the ller neck. The oil delivery may otherwise be

impaired.

NOTICE: Use the saw chain oil exclusively for

Makita/Dolmar chain saws or equivalent oil avail-

able in the market.

NOTICE: Never use oil including dust and parti-

cles or volatile oil.

NOTICE: When pruning trees, use botanical oil.

Mineral oil may harm trees.

NOTICE: Before the cutting operation, make sure

that the provided oil tank cap is screwed in place.

WORKING WITH THE CHAIN SAW

CAUTION: The rst time user should, as a

minimum practice, do cutting logs on a saw-horse

or cradle.

CAUTION: When sawing precut timber, use a

safe support (saw horse or cradle). Do not steady

the workpiece with your foot, and do not allow

anyone else to hold or steady it.

CAUTION: Secure round pieces against

rotation.

CAUTION: Keep all parts of the body away

from the saw chain when the motor is operating.

CAUTION: Hold the chain saw rmly with

both hands when the motor is running.

CAUTION: Do not overreach. Keep proper

footing and balance at all times.

NOTICE: Never toss or drop the tool.

NOTICE: Do not cover the vents of the tool.

Pruning trees

Bring the chain saw body into contact with the branch to

be cut before switching on. Otherwise it may cause the

guide bar to wobble, resulting in injury to operator. Saw

the wood to be cut by just moving it down by using the

weight of the chain saw.

► Fig.20

If you cannot cut the timber right through with a single

stroke:

Apply light pressure to the handle and continue sawing

and draw the chain saw back a little.

► Fig.21

When cutting thick branches, rst make a shallow

undercut and then make the nish cut from the top.

► Fig.22

If you try to cut off thick branches from the bottom, the

branch may close in and pinch the saw chain in the cut.

If you try to cut off thick branches from the top without a

shallow undercut, the branch may splinter.

► Fig.23

Bucking

1. Rest the chain saw body on the wood to be cut.

► Fig.24

2. With the saw chain running, saw into the wood

while using the top handle to raise the saw and the front

one to guide it.

3. Continue the cut by applying slight pressure to the

top handle, easing the saw back slightly.

NOTICE: When making several cuts, switch the

chain saw off between cuts.

CAUTION: If the upper edge of the bar is used

for cutting, the chain saw may be deected in

your direction if the chain becomes trapped. For

this reason, cut with the lower edge, so that the

saw will be deected away from your body.

► Fig.25

Carrying tool

Before carrying the tool, always apply the chain brake

and remove the battery cartridges from the tool. Then

attach the guide bar cover. Also cover the battery car-

tridge with the battery cover.

► Fig.26: 1. Guide bar cover 2. Battery cover

MAINTENANCE

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before attempting to perform inspection or

maintenance.

CAUTION: Always wear gloves when perform-

ing any inspection or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita/Dolmar Authorized or Factory Service

Centers, always using Makita/Dolmar replacement parts.

Sharpening the saw chain

Sharpen the saw chain when:

•

Mealy sawdust is produced when damp wood is cut;

• The chain penetrates the wood with difculty, even

when heavy pressure is applied;

• The cutting edge is obviously damaged;

• The saw pulls to the left or right in the wood.

(caused by uneven sharpening of the saw chain or

damage to one side only)

Sharpen the saw chain frequently but a little each time.

Two or three strokes with a le are usually sufcient for

routine resharpening. When the saw chain has been

resharpened several times, have it sharpened in our

authorized service center.

17 ENGLISH

Sharpening criteria:

WARNING: An excessive distance between

the cutting edge and depth gauge increases the

risk of kickback.

► Fig.27: 1. Cutter length 2. Distance between cutting

edge and depth gauge 3. Minimum cutter

length (3 mm)

— All cutter length must be equal. Different cutter

lengths prevent the saw chain from running

smoothly and may cause the saw chain to break.

— Do not sharpen the chain when the cutter length

has reached 3 mm or shorter. The chain must be

replaced with new one.

— The chip thickness is determined by the distance

between the depth gauge (round nose) and the

cutting edge.

— The best cutting results are obtained with following

distance between cutting edge and depth gauge.

• Chain blade 90PX : 0.65 mm

• Chain blade 91PX : 0.65 mm

► Fig.28

— The sharpening angle of 30° must be the same on

all cutters. Different cutter angles cause the chain

to run roughly and unevenly, accelerate wear, and

lead to chain breaks.

— Use a suitable round le so that the proper sharp-

ening angle is kept against the teeth.

• Chain blade 90PX : 55°

• Chain blade 91PX : 55°

File and le guiding

— Use a special round le (optional accessory) for

saw chains to sharpen the chain. Normal round

les are not suitable.

— Diameter of the round le for each saw chain is as

follows:

• Chain blade 90PX : 4.5 mm

• Chain blade 91PX : 4.0 mm

— The le should only engage the cutter on the for-

ward stroke. Lift the le off the cutter on the return

stroke.

— Sharpen the shortest cutter rst. Then the length

of this shortest cutter becomes the standard for all

other cutters on the saw chain.

— Guide the le as shown in the gure.

► Fig.29: 1. File 2. Saw chain

— The le can be guided more easily if a le holder

(optional accessory) is employed. The le holder

has markings for the correct sharpening angle of

30° (align the markings parallel to the saw chain)

and limits the depth of penetration (to 4/5 of the

le diameter).

► Fig.30: 1. File holder

— After sharpening the chain, check the height of the

depth gauge using the chain gauge tool (optional

accessory).

► Fig.31

— Remove any projecting material, however small,

with a special at le (optional accessory).

— Round off the front of the depth gauge again.

Cleaning the guide bar

Chips and sawdust will build up in the guide bar groove.

They may clog the bar groove and impair the oil ow.

Clean out the chips and sawdust every time when you

sharpen or replace the saw chain.

► Fig.32

Cleaning the sprocket cover

Chips and saw dust will accumulate inside of the

sprocket cover. Remove the sprocket cover and saw

chain from the tool then clean the chips and saw dust.

► Fig.33

Cleaning the oil discharge hole

Small dust or particles may be built up in the oil dis-

charge hole during operation. These dust or particles

may impair the oil to ow and cause an insufcient

lubrication on the whole saw chain. When a poor chain

oil delivery occurs at the top of guide bar, clean the oil

discharge hole as follows.

1. Remove the sprocket cover and saw chain from

the tool.

2. Remove the small dust or particles using a slotted

screwdriver or the like.

► Fig.34: 1. Slotted screwdriver 2. Oil discharge hole

3. Insert the battery cartridge into the tool. Pull the

switch trigger to ow built-up dust or particles off the oil

discharge hole by discharging chain oil.

4. Remove the battery cartridge from the tool.

Reinstall the sprocket cover and saw chain on the tool.

Replacing the sprocket

CAUTION: A worn sprocket will damage a

new saw chain. Have the sprocket replaced in this

case.

Before tting a new saw chain, check the condition of

the sprocket.

► Fig.35: 1. Sprocket 2. Areas to be worn out

Always t a new locking ring when replacing the

sprocket.

► Fig.36: 1. Locking ring 2. Sprocket

NOTICE: Make sure that the sprocket is installed

as shown in the gure.

Storing the tool

1. Clean the tool before storing. Remove any chips

and sawdust from the tool after removing the sprocket

cover.

2. After cleaning the tool, run it under no load to lubri-

cate the saw chain and guide bar.

3. Cover the guide bar with the guide bar cover.

4. Empty the oil tank.

18 ENGLISH

Instructions for periodic maintenance

To ensure long life, prevent damage and ensure the full functioning of the safety features, the following maintenance

must be performed regularly. Warranty claims can be recognized only if this work is performed regularly and prop-

erly. Failure to perform the prescribed maintenance work can lead to accidents! The user of the chain saw must not

perform maintenance work which is not described in the instruction manual. All such work must be carried out by our

authorized service center.

Check item / Operating time Before

operation

Everyday Every week Every 3

month

Annually Before

storage

Chain saw Inspection.

- - - - -

Cleaning. -

- - - -

Check at

authorized

service center.

- - - -

Saw chain Inspection. - - - - -

Sharpening if

necessary.

- - - - -

Guide bar Inspection. - - - -

Remove from

the chain saw.

- - - - -

Chain brake Check the

function.

- - - - -

Have it

inspected

regularly at

authorized

service center.

- - -

- -

Chain

lubrication

Check the oil

feed rate.

- - - - -

Switch trigger Inspection.

- - - - -

Lock-off lever Inspection.

- - - - -

Oil tank cap Check

tightness.

- - - - -

Chain catcher Inspection. - -

- - -

Screws and

nuts

Inspection. - -

- - -

19 ENGLISH

TROUBLESHOOTING

Before asking for repairs, conduct your own inspection rst. If you nd a problem that is not explained in the manual,

do not attempt to dismantle the tool. Instead, ask Makita/Dolmar Authorized Service Centers, always using Makita/

Dolmar replacement parts for repairs.

Malfunction status Cause Action

The chain saw does not start. Battery cartridge is not installed. Install a charged battery cartridge.

Battery problem (low voltage).

Recharge the battery cartridges. If recharging

is not effective, replace the battery cartridge.

Main power switch is off. The chain saw is automatically turned off if

it is un-operated for a certain period. Turn

on the main power switch again.

The saw chain does not run. Chain brake activated. Release chain brake.

The motor stops running after a little use. Battery's charge level is low.

Recharge the battery cartridges. If recharging

is not effective, replace the battery cartridge.

No oil on the chain. Oil tank is empty. Fill the oil tank.

Oil guide groove is dirty. Clean the groove.

Poor oil delivery. Adjust the amount of oil delivery with the

adjusting screw.

The chain saw does not reach maximum

RPM.

Battery cartridge is installed improperly. Install the battery cartridges as described

in this manual.

Battery power is dropping. Recharge the battery cartridge. If recharg-

ing is not effective, replace the battery

cartridge.

The drive system does not work correctly. Ask the authorized service center in your

region for repair.

The main power lamp is blinking in green. Switch trigger is pulled under an unoperat-

able condition.

Pull the switch trigger after the main power switch

is turned on and the chain brake is released.

Chain does not stop even the chain brake

is activated:

Stop the machine immediately!

The brake band is worn down. Ask the authorized service center in your

region for repair.

Abnormal vibration:

Stop the machine immediately!

Loose guide bar or saw chain. Adjust the guide bar and saw chain

tension.

Tool malfunction. Ask the authorized service center in your

region for repair.

The Torque Boost mode is not available

after replacing the battery cartridge with a

fully charged one.

Depending on the usage conditions, the

Torque Boost mode is not available after

replacing the battery cartridge.

Use the tool in the normal mode until the

installed battery cartridge becomes empty,

and then replace the battery cartridge with

a fully charged one, or recharge the battery

cartridge.

The saw chain cannot be installed. The combination of saw chain and

sprocket is not correct.

Use the correct combination of saw chain

and sprocket by referring to the section for

specications.

OPTIONAL ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita/

Dolmar tool specied in this manual. The use of

any other accessories or attachments might present

a risk of injury to persons. Only use accessory or

attachment for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita/Dolmar

Service Center.

• Saw chain

• Guide bar

• Guide bar cover

• Sprocket

• File

• Makita/Dolmar genuine battery and charger

WARNING: If you purchase a guide bar of

different length from the standard guide bar, also

purchase a suitable guide bar cover together. It

must t and fully cover the guide bar on the chain

saw.

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

differ from country to country.

20 FRANÇAIS

FRANÇAIS (Instructions originales)

SPÉCIFICATIONS

Modèle : AS4030 AS4035

Longueur totale (sans guide-chaîne) 270 mm

Tension nominale 36 V CC

Poids net *1 4,2 kg

*2 4,7 - 4,9 kg 4,8 - 5,0 kg

Longueur du guide-chaîne standard 300 mm 350 mm

Longueur de guide-chaîne

recommandée

avec 90PX 250 - 400 mm

avec 91PX 250 - 400 mm

Type de chaîne applicable

(reportez-vous au tableau ci-dessous.)

90PX

91PX

Pignon standard Nombre de dents 6

Pas 3/8″

Vitesse de la chaîne 0 - 20 m/s

(0 - 1 200 m/min)

Capacité du réservoir d’huile pour chaîne 200 cm

• Étant donné l’évolution constante de notre programme de recherche et de développement, les spécications

contenues dans ce manuel sont sujettes à modication sans préavis.

• Les spécications peuvent varier suivant les pays.

*1 : Le poids, avec la batterie la plus grande et le réservoir d’huile vide, sans le guide-chaîne et la chaîne, selon la

norme EN ISO 11681-2.

*2 : Le poids combiné le plus léger et le plus lourd selon la procédure EPTA 01/2014. Le poids peut être différent

selon les accessoires, notamment la batterie.

Batterie applicable

BL1830 / BL1830B / BL1840 / BL1840B / BL1850 / BL1850B / BL1860B

• Certaines batteries répertoriées ci-dessus peuvent ne pas être disponibles selon la région où vous résidez.

AVERTISSEMENT : N’utilisez que les batteries répertoriées ci-dessus. L’utilisation de n’importe quelle

autre batterie peut provoquer des blessures et/ou un incendie.

Combinaison de chaîne, guide-chaîne et pignon

Type de chaîne 90PX

Nombre de maillons d’entraînement 46 52

Guide-chaîne Longueur du guide-chaîne 300 mm 350 mm

Longueur de coupe 294 mm 350 mm

Pas 3/8″

Jauge 1,1 mm

Type Guide-chaîne à pignon de renvoi

Pignon Nombre de dents 6

Pas 3/8″

Type de chaîne 91PX

Nombre de maillons d’entraînement 46 52

Guide-chaîne Longueur du guide-chaîne 300 mm 350 mm

Longueur de coupe 294 mm 350 mm

Pas 3/8″

Jauge 1,3 mm

Type Guide-chaîne à pignon de renvoi

Pignon Nombre de dents 6

Pas 3/8″

Sayfa yükleniyor ...

Dolmar AS4030 El kitabı

Marka: Dolmar

Model: AS4030

Kategori: Motorlu testereler

Tip: El kitabı

PDF İndir

rapor

Diğer dillerde

español: Dolmar AS4030 El manual del propietario
français: Dolmar AS4030 Le manuel du propriétaire
italiano: Dolmar AS4030 Manuale del proprietario
Deutsch: Dolmar AS4030 Bedienungsanleitung
português: Dolmar AS4030 Manual do proprietário
dansk: Dolmar AS4030 Brugervejledning
Nederlands: Dolmar AS4030 de handleiding

Dolmar AS4030 El kitabı

Dolmar AS4030 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler