Yamaha n12 Kullanım kılavuzu

Marka: Yamaha

Model: n12

Kategori: Ses amplifikatörleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

N-12

NEXO 45°N 12

Line Monitor

User Manual

45°N-12 User Manual V1.01

Date: 15/12/2010

Page 2/25 INTRODUCTION

PLEASE READ CAREFULLY BEFORE PROCEEDING

BASIC PRECAUTIONS

Do not open the speaker system or attempt to disassemble the internal parts or modify them in any

way. The speaker system contains no user-serviceable parts. If it should appear to be malfunctioning

or damaged, discontinue use immediately and have it inspected by qualified NEXO service personnel.

Water exposure: Do not expose the speaker system to direct rain, do not use it near water or in wet

conditions. Do not place containers with liquid on speaker system as they might spill into openings. If

any liquid such as water seeps into the speaker system, have it inspected by qualified NEXO

personnel.

SYSTEM DEPLOYMENT SAFETY RULES

Read User Manual before deployment. Before use of enclosed speaker system,

please ensure that anyone involved in system deployment understands the rigging –

stacking – pole mounting safety rules as described in the speaker system User Manual.

Failure to do this exposes people to potential injury or death.

Always consult qualified NEXO personnel if the device installation requires construction work and make

sure to observe the following precautions:

Mounting precautions

- choose mounting hardware and an installation location that can support the weight of the speaker

system;

- do not use speaker system handles for suspended installation;

- do not expose speaker system to excessive dust or vibration, or extreme cold or heat to prevent

possibility of component damage;

- do not place the speaker system in an unstable position from which it might fall accidentally;

- if speaker systems uses a stand, ensure that stand specifications are adapted, and that stand

height does not exceed 1.40m/55”; never move the stand while the speaker is in position.

Connection and powering precautions

- remove all connected cables before moving the speaker system;

- turn off AC power of all power amplifier units before connecting the speaker system;

- when turning on the AC power to the audio system, always turn on the power amplifier last; when

turning the AC power off, always turn off the power amplifier first;

- when used in cold conditions, a gradual power ramp up should applied to the system on an 5 mn

period to allow the loudspeaker components to stabilize during the very first minutes of usage.

Inspect the speaker system periodically.

INTRODUCTION Page 3/25

SAFETY INSTRUCTIONS FOR NEXO TD CONTROLLERS

NEXO ANALOGUE PSTDCONTROLLERS, NX242 DIGITAL CONTROLLER,

NXAMP4x1 AND NXAMP4x4 POWERED CONTROLLERS ARE CLASS 1

APPARATUS AND MUST BE EARTHED.

THE GREEN AND YELLOW WIRE OF THE MAINS CORD MUST ALWAYS BE CONNECTED TO AN

INSTALLATION SAFETY EARTH OR GROUND. THE EARTH IS ESSENTIAL FOR PERSONAL

SAFETY AS WELL AS THE CORRECT OPERATION OF THE SYSTEM, AND IS INTERNALLY

CONNECTED TO ALL EXPOSED METAL SURFACES.

- Read these instructions.

- Keep these instructions.

- Heed all warnings.

- Follow all instructions.

- Do not use this apparatus near water.

- Clean only with dry cloth.

- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus

(including amplifiers) that produce heat.

- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two

blades with one wider than the other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your safety. If the provided plug does not

fit into your outlet, consult an electrician for replacement of the obsolete outlet. (US market)

- Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

- Only use attachments/accessories specified by the manufacturer.

- Unplug this apparatus during lightning storms or when unused for long periods of time.

- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has

been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does

not operate normally, or has been dropped.

To avoid electrical shock, do not remove covers.

Dangerous voltages exist inside.

Refer all servicing to qualified personnel only.

WARNING: To reduce the risk of fire or electric shock,

do not expose this apparatus to rain or moisture.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

The lightning flash with arrowhead

symbol, within an equilateral triangle

is intended to alert the user to the

presence of uninsulated “dangerous

voltage” within the product's

enclosure that may be of sufficient

magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and

maintenance (servicing) instructions

in the literature accompanying

the appliance.

Page 4/25 INTRODUCTION

HIGH SOUND PRESSURE LEVELS

Exposure to extremely high noise levels may cause permanent hearing loss.

Individuals vary considerably in susceptibility to noise-induced hearing loss but nearly

everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient

period of time. The U.S. Government’s Occupational and Health Administration (OSHA)

has specified the following permissible noise level exposures: Sound Duration Per

Day In Hours Sound Level dBA, Slow Response

8 90

6 92

4 65

3 97

2 100

1 ½ 102

1 105

½ 110

¼ or less 115

According to OSHA, any exposure in excess of the above permissible limits could result in some

hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating

this amplification system in order to prevent permanent hearing loss, if exposure is in excess of the

limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure

levels, it is recommended that all persons exposed to equipment capable of producing high sound

pressure levels such as this amplification system be protected by hearing protectors while this unit is in

operation.

DISPOSAL OF OLD ELECTRICAL & ELECTRONIC EQUIPMENT

This symbol on the product or on its packaging indicates that it shall not be treated

as household waste. Instead it shall be handed over to the applicable collection

point for the recycling of electrical and electronic equipment. By ensuring this

product is disposed of correctly, you will help prevent potential negative

consequence for the environment and human health, which could otherwise be

caused by inappropriate waste handling of this product. The recycling of materials

will help to conserve natural resources. For more detailed information about

recycling of this product, please contact your local city office, your household waste

disposal service or the shop where you purchased the product.

INTRODUCTION Page 5/25

CONTENTS

1 Introduction............................................................................................................................................... 6

2 45N12 General Set-up Instructions.......................................................................................................... 8

2.1 Speaker connection............................................................................................................................ 8

2.1.1 45°N-12 Connector Panel .......................................................................................................... 8

2.1.2 Configuring 45N12 for Passive or Active Mode.......................................................................... 9

2.1.3 Cabling..................................................................................................................................... 10

3 Amplifier Selection for use with 45°N-12............................................................................................... 11

3.1 45N12 recommended amplification................................................................................................... 11

3.1.1 Current rating........................................................................................................................... 11

3.1.2 Amplifier settings...................................................................................................................... 11

3.2 45°N-12 and NXAMP TDControllers.................................................................................................13

3.2.1 NXAMP connectors.................................................................................................................. 13

3.2.2 45°N-12 and NXAMP recommended configurations................................................................. 13

4 Connection diagrams.............................................................................................................................. 14

4.1 45°N-12 / NXAMP4x1 - Bridge Stereo – Active mode....................................................................... 14

4.2 45°N-12 / NXAMP4x1 - Bridge Stereo – Passive mode.................................................................... 15

4.3 45N12 / NXAMP4x4 - 4 Channels – Active Mode............................................................................. 16

4.4 45°N-12 / NXAMP4x4 - 4 Channels – Passive Mode........................................................................ 17

4.5 45°N-12 / NX242-ES4 – Active Mode...............................................................................................18

4.6 45°N-12 / NX242-ES4 – Passive Mode ............................................................................................ 19

5 Application guidelines............................................................................................................................ 20

5.1 SAFETY FIRST................................................................................................................................ 20

5.2 45°N-12 Coverage............................................................................................................................ 20

5.3 Handling 45 N-12 on stage............................................................................................................... 21

5.4 Stage monitoring applications........................................................................................................... 22

5.5 Testing and Maintenance of the system ...........................................................................................22

6 45°N-12 Technical Specifications .......................................................................................................... 23

6.1 System specifications....................................................................................................................... 23

6.2 Dimensions....................................................................................................................................... 24

6.3 Component List ................................................................................................................................ 24

7 USER NOTES........................................................................................................................................... 25

Page 6/25 INTRODUCTION

1 INTRODUCTION

Thank you for selecting a NEXO 45°N-12 floor monitor.

NEXO’s 45°N-12 monitor loudspeaker is the first product based on a radical new concept in stage

sound – that of line monitoring.

The revolutionary NEXO 45°N-12 wedge monitor brings all the benefits of line-array technology to the

stage.

It draws on NEXO’s patented Hyperbolic Reflective Wavesource which is used throughout the GEO

range of high-performance loudspeakers. The design works by wavesourcing, creating virtual acoustic

sources behind the enclosure itself and below the stage, using reflection rather than coercion to

determine the shape of the wavefront.

Unlike a conventional high frequency waveguide in which the exit is rectangular, the NEXO monitor’s

waveguide enables cabinets to be linked together to form arrays without interference between

wavefronts.

Practical benefits for stage monitoring applications are:

- steady frequency in coverage area;

- higher SPL and feedback threshold;

- sharp side attenuation;

- coverage and SPL scalability.

This manual is intended to provide you with necessary and useful information about your NEXO 45°N-

12 floor monitor system.

INTRODUCTION Page 7/25

As for all NEXO systems, NEXO 45°N-12 is controlled, powered and monitored by dedicated NEXO

TDControllers:

NX242-ES4 Digital TDController provides comprehensive control of N12 line monitors in multiple

configurations. It allows EthersoundTM digital audio networking, as well as remote control for all units in

the network. It has 2 analogue / 4 digital inputs and 4 analogue / 4 digital outputs.

IMPORTANT

NX242 must be equipped with NX-Tension Card (NX-ES4) to access N12 setups

NXAMP4x1 and NXAMP 4x4 are Powered Digital Controllers, providing full control and amplification for

45N12 in multiple configurations. Both devices feature 4 analogue inputs and 4 speaker outputs. When

equipped with optional card, 4 digital inputs in EthersoundTM digital audio network format as well as

remote control for all units in the network become available.

For a complete description of these controllers, please refer to User Manuals. The NX242 and NXAMP

DSP algorithms and parameters are fixed in software and updated regularly: Please consult the NEXO

web site (www.nexo.fr

) for the latest software releases.

GeoD Passive mode

Crossover 80Hz

Page 8/25 45N12 GENERAL SET-UP INSTRUCTIONS

2 45N12 GENERAL SET-UP INSTRUCTIONS

2.1 Speaker connection

NEXO 45°N-12 are connected with Speakon NL4FC plugs (not supplied). A wiring diagram is printed on

the connection panel located on the back of each cabinet. The 4 pins of the 2 Speakon sockets

identified in / out are connected in parallel within the enclosure.

Either connector can be used to connect amplifier or to link to an additional 45N12 cabinet.

2.1.1 45°N-12 Connector Panel

Connectors are wired as follows:

Speakon

Connector

Passive

Mode

Active

Mode

1(-)

Not Connected 45N12 LF (-)

1(+)

Not Connected 45N12 LF (+)

2(-)

45N12 (-) 45N12 HF (-)

2(+)

45N12 (+) 45N12 HF (+)

45N12 GENERAL SET-UP INSTRUCTIONS Page 9/25

LF +

LF -

HF +

HF -

LF +

LF -

HF + HF -

IMPORTANT

45N12 are factory configured in active mode

2.1.2 Configuring 45N12 for Passive or Active Mode

In order to change active or passive configuration:

- remove the TORX screws that hold the rear/bottom metal panel;

- remove the rear/bottom metal panel to access passive network WAGO connectors.

In Passive Mode, WAGO connector should be inserted in “Passive In”, and speakers WAGO

connectors should be inserted in connector “Passive Out”.

In Active Mode, WAGO Connector should be directly connected to speakers via speakers WAGO

connectors (passive filter is then bypassed).

PASSIVE MODE CONFIGURATION

ACTIVE MODE CONFIGURATION

Page 10/25 45N12 GENERAL SET-UP INSTRUCTIONS

2.1.3 Cabling

NEXO recommends the exclusive use of multi-conductor cables to connect the system: the cable kit is

compatible with all the cabinets, and there is no possible confusion between LF and HF sections.

Cable choice consists mainly of selecting cables of the correct sectional dimension (size) in relation to

the load resistance and the cable length. Too small a cable section will increase both its serial

resistance and its capacitance; this reduces the electrical power delivered to the loudspeaker and can

also induce response (damping factor) variations.

For a serial resistance less or equal to 4% of the load impedance (damping factor = 25), the maximum

cable length is given by:

max

= Z x S S in mm

, Z in Ohm, L

max

in meters

The table below indicates these values, for 3 common sizes.

Load Impedance (Ω)

2 3 4 6 8 12 16

Cable section Maximum Length (meters)

1,5 mm² (AWG #14) 3 4.5 6 9 12 18 24

2,5 mm² (AWG #12) 5 7.5 10 15 20 30 40

4 mm² (AWG #10) 8 12 16 24 32 48 64

IMPORTANT

Long speaker cables induce capacitive effects – up to hundreds of pF depending on the

quality of the cable - with a low-pass effect on high frequencies. If long speaker cables

must be used, ensure that they do not remain coiled while in use.

AMPLIFIER SELECTION FOR USE WITH 45 N-12 Page 11/25

3 AMPLIFIER SELECTION FOR USE WITH 45°N-12

NEXO recommends high power amplifiers in all cases. Budget constraints are the only reason to select

lower power amplifiers. A lower power amplifier will not reduce the chances of driver damage due to

over-excursion, and may actually increase the risk of thermal damage due to sustained clipping. If an

incident occurs on an installation without protection, the fact that amplifiers only generating half their

rated output power (-3dB) are used will not change anything in respect of possible damage. This is due

to the fact that the RMS power handling of the weakest component in the system is always 6 to 10 dB

lower than the amplifier rating.

3.1 45N12 recommended amplification

Nexo recommends amplifiers in agreement with table below:

Recommended

Amplifier#

Channel 1

LF in Active Mode or

LF+HF in Passive Mode

Channel 2

HF in Active Mode

45N12 Passive Mode 1200 to 2000 W / 8 Ohms

45N12 Active Mode 1000 to 1500 W / 8 Ohms 250 to 500 W / 16 Ohms

3.1.1 Current rating

It is very important that the amplifier behaves correctly under low load conditions. A speaker system is

reactive by nature: on transient signals like music it will require four to ten times more instantaneous

current than its nominal impedance would indicate. Amplifiers are generally specified by continuous

RMS power into resistive loads, however the only useful information about current capacity is the

specification into a 2 Ohm load. It is possible to perform an amplifier listening test by loading the amps

with twice the number of cabinets considered for the application (2 speakers per channel instead of one,

4 instead of 2) and running the amps up to the onset of clipping. If the signal does not noticeably

deteriorate, the amplifier is well adapted (overheating after approximately ten minutes is normal but

thermal protection must not operate too quickly after starting this test).

3.1.2 Amplifier settings

Gain value

Gain is the key to correct alignment of the system. It is especially important to know the gain of all

amplifiers used in your set-up. The tolerance should be about ±0.5 dB. In practice this can be difficult to

achieve because:

Some amplifier brands have an identical input sensitivity for models of different power rating (this infers

a different voltage gain for each model). For example, a range of amplifiers with different power outputs,

all having a published input sensitivity of 775mV/0dBm or 1.55V/+6dBm, will have a wide range of

actual gains – the higher the power, the greater the gain.

Various other brands may offer constant gain but only within a given product range, for example they

may fit fixed input sensitivity only on their semi-professional amps.

Even if a manufacturer applies the constant gain rule to all models, the value selected will not

necessarily be the same as that chosen by other manufacturers.

Some products can exhibit manufacturing tolerances for the same model of ±1dB or more. Some

amplifiers may have been modified, possibly without any label indicating the new values. Others may

have gain switches fitted internally where it is impossible for the user to verify the actual setting without

opening the amplifier casing.

In cases where you don't know the gain of your amplifier (or want to check it) please follow this

procedure:

- unplug any loudspeakers from the amplifier outputs

- feed a sine wave at 1000Hz at a known voltage (~ 0.5V) to the input of the amplifier under test

Page 12/25 AMPLIFIER SELECTION FOR USE WITH 45 N-12

- measure the voltage at the output of the amplifier

- calculate the gain using the formula Gain = 20 * LOG10(Vout/Vin).

Some examples:

Vin / Gain 20dB 26dB 32dB 37dB (1.4V sensitivity / 1350Wrms)

0.1 V 1 V 2 V 4 V 7.1 V

0.5 V 5 V 10 V 20 V 35.4 V

1 V 10 V 20 V 40 V 70.8 V

Remember that constant sensitivity settings will give a different gain value when the amplifier power is

different.

NEXO recommends 26 dB gain amplifiers, as it is at the same time adequately low and quite common

amongst amplifier manufacturers. This gain setting improves signal to noise ratio and allows all

preceding electronic equipment, including the NX242-ES4 TDcontroller, to operate at optimum level.

Using a high gain amplifier will raise the noise floor proportionally.

Operating Mode

Most two channel amplifiers available on the pro-audio market have the following operating modes:

Stereo:

two fully independent channels deliver identical power into identical loads

NEXO recommends Stereo Mode for all amplifier channels feeding 45°N-12 monitors.

Bridge-Mono:

the second signal channel processes the same input as the first channel, but with

reversed phase. The (single) load is connected between the two positive channel outputs using a

suitable connection. While the total output of the amplifier remains the same, the available output

voltage, the minimum impedance that can be connected and the voltage gain are doubled as compared

with stereo operation. Typically, only channel 1 input is active. Positive and negative output connections

vary depending on amplifier manufacturers.

NEXO does not recommend Bridge Mono Mode unless amplifier power is clearly not sufficient.

IMPORTANT

When in Bridge-Mono mode, check your amplifier user manual for proper connection of

outputs 1(+) and (2+) in relation to input phase.

Parallel-mono:

the output terminals of the two channels are configured in parallel using an internal relay.

The (single) load is connected either to the output of channel 1 or to that of channel 2 (as if in stereo).

While the total output of the amplifier remains the same the output voltage level is also the same as in

stereo mode. The minimum impedance that can be connected is reduced by half due to the fact that

current capability is doubled. Typically, only channel 1 input is active.

NEXO does not recommend Parallel-Mono Mode for any PS Series speaker amplification.

Warning on amplifiers signal processing features

Some high-end amplifiers may include signal processing functions similar to those found in the NX242

TDcontroller ("loudspeaker offset integration", "limiter", "compressor," etc.). Moreover, when this

processing is digital, computation latency time can introduce a few milliseconds delay from input to

output. These functions are not adapted to specific system requirements and may interfere with the

complex protection algorithms used in the NEXO TD Controllers.

NEXO do not advise using other protection systems in conjunction with the NEXO TD Controllers and

they should be disabled.

IMPORTANT

For proper system protection, no latency time or non-linear devices should be

introduced between the output of the NEXO TDcontroller and the input of loudspeakers

through use of DSP modules such as internal amplifier signal processing.

AMPLIFIER SELECTION FOR USE WITH 45 N-12 Page 13/25

3.2 45°N-12 and NXAMP TDControllers

NEXO Powered TDControllers NXAMP 4X1 & 4X4 are integrated solutions for Control and amplification

for all NEXO speaker ranges.

NXAMP4x1 and NXAMP4x4 power capability is listed in the table below:

Mode 4 Channels Bridge Stereo

NXAMP4x1 4 x 650 Watts / 8 Ohms

4 x 900 Watts / 4 Ohms

4 x 1300 Watts / 2 Ohms

2 x 1800 Watts / 8 Ohms

2 x 2600 Watts / 4 Ohms

NXAMP4x4 4 x 1900 Watts / 8 Ohms

4 x 3400 Watts / 4 Ohms

4 x 4000 Watts / 2 Ohms

2 x 6800 Watts / 8 Ohms

2 x 8000 Watts / 4 Ohms

3.2.1 NXAMP connectors

NXAMP4x1 and NXAMP4x4 rear panels feature:

- 4 analog inputs / outputs (links) on XLR3 connectors;

- 4 digital inputs / outputs on RJ45 connectors with optional card;

- 4 speaker level outputs on NL4FC connectors.

Figure below shows connectors implementation on the rear panel.

3.2.2 45°N-12 and NXAMP recommended configurations

Below table lists basic requirements for proper use of NXAMP TD Controllers in conjunction with 45°N-

12:

Passive Mode Active Mode

1 or 2 x 45°N-12 1 channel of NXAMP4x1 in Bridge Stereo Mode

1 channel of NXAMP4x4 in 4 channels Mode

2 channels of NXAMP4x1 in Bridge Stereo Mode

2 channels of NXAMP4x4 in 4 channels Mode

3 x 45°N-12 1 channel of NXAMP4x4 in 4 channels Mode 2 channels of NXAMP4x4 in 4 channels Mode

Please refer to following documents (available at www.nexo-sa.com

) for detailed information on specific

configurations:

- NXAMP4x1 and NXAMP4x4 User Manual

- NXAMP Application Guideline

- NXAMP Load Setup list

Page 14/25 CONNECTION DIAGRAMS

4 CONNECTION DIAGRAMS

4.1 45°N-12 / NXAMP4x1 - Bridge Stereo – Active mode

IN A

OUT A

OUT D

3 x HF

3 x LF

SP4

2+/2-

1+/1-

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

SP4

CONNECTION DIAGRAMS Page 15/25

IN A

IN B

OUT B

BRIDGED MODE

OUT D

BRIDGED MODE

SP4

2+/2- HF+LF

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

4.2 45°N-12 / NXAMP4x1 - Bridge Stereo – Passive mode

Page 16/25 CONNECTION DIAGRAMS

OUT A

OUT C

IN B

IN A

SP4

2+/2- HF

1+/1- LF

2+/2- HF

1+/1- LF

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

4.3 45N12 / NXAMP4x4 - 4 Channels – Active Mode

CONNECTION DIAGRAMS Page 17/25

OUT A

IN B

IN A

OUT D

IN D

IN C

SP4

OUT B

OUT C

2+/2- HF+LF

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out I n

4.4 45°N-12 / NXAMP4x4 - 4 Channels – Passive Mode

Page 18/25 CONNECTION DIAGRAMS

AMPLIFIER 1

AMPLIFIER 2

N12 #2

TO AMPLIFIERS

STEREO

FROM AMPLIFIERS

N12 #2

+ 4 - + 3-

STEREO

+ 2 - + 1 -

N12 #2

N12 #1

3 x HF

3 x LF

SP4

2+/2-

1+/1-

3 x HF

3 x LF

SP4

2+/2-

1+/1-

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

4.5 45°N-12 / NX242-ES4 – Active Mode

CONNECTION DIAGRAMS Page 19/25

AMPLIFIER

TO AMPLIFIERS

STEREO

FROM AMPLIFIERS

N12 #2

+ 4 - + 3-

+ 2 - + 1 -

N12 #2

N12 #1

SP4

2+/2- HF+LF

SP4

2+/2- HF+LF

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

NXtension-ES

In Rx

In Tx

Out Rx

Out Tx

Out In

4.6 45°N-12 / NX242-ES4 – Passive Mode

Page 20/25 APPLICATION GUIDELINES

5 APPLICATION GUIDELINES

5.1 SAFETY FIRST

Before proceeding with installation of 45°N-12, please ensure that the components are present and

undamaged. In the event of any shortage, please contact your supplier.

Statistically, many more injuries occur due to unstable ground set systems than those associated with

flown systems. There are several reasons for this fact, however the message is clear:

Always survey the supporting structure upon which 45°N-12 is to be set. Inspect stage support and if

necessary ask for the stage scrims and dressings be removed to allow access.

If the stage surface slopes, as it does in some theatres, ensure that the system is prevented from sliding

forwards due to vibration. This may require the fitting of timber battens to the stage floor.

For outdoor systems ensure that that the system is protected from wind forces which might cause the

monitor system to become unstable. Wind forces can be huge, especially upon large systems, and

should never be underestimated. Observe meteorological forecasts, calculate the “worst case” effect

upon the system prior to erection and ensure that the system is secured appropriately.

Be aware that safety procedures are as important in the truck and in the warehouse as they are at the

venue.

5.2 45°N-12 Coverage

Below figures illustrate 45°N-12 horizontal and vertical coverage behavior.

Main coverage features are:

- 30° horizontal coverage, scalable by 30° steps by arraying units;

- Asymetrical vertical coverage, defined so that frequency response level within +/-3 dB

from 0 to 2 meters.

HORIZONTAL AND VERTICAL COVERAGE

Sayfa yükleniyor ...

Yamaha n12 Kullanım kılavuzu

Marka: Yamaha

Model: n12

Kategori: Ses amplifikatörleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

N-12

PDF İndir

rapor

Yamaha n12 Kullanım kılavuzu

Bu kılavuz için de uygundur

Yamaha n12 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler