Yamaha NSNSW100PB SUB 100 BK El kitabı

NS-NSW100

GEFS

PT

RU

NL

ES

IT

SV

DE

FR

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

MANUAL DO PROPRIETÁRIO

GEBRUIKSAANWIJZING

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

Network Subwoofer

Caisson Connecté

Сетевой сабвуфер

EN

OWNER’S MANUAL

2 En

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE USE.

BE SURE TO FOLLOW THESE

INSTRUCTIONS.

The precautions listed below are to prevent risk of harm

to the user and others, as well as to prevent property

damage, and to help the user use this unit properly and

safely. Be sure to follow these instructions.

After reading this manual, be sure to keep it in a safe place where

it can be referenced at any time.

WARNING

This content indicates “risk of serious injury or death.”

Power supply/power cord

• Do not do anything that could damage the power cord.

– Do not place it near a heater.

– Do not bend it excessively or alter it.

– Do not scratch it.

– Do not place it under a heavy object.

Using the power cord with the core of the cord exposed could

cause electric shocks or a fire.

• Do not touch the power plug or cord if there is a chance of

lightning. Failure to observe this may cause electric shocks.

• Use this unit with the power supply voltage printed on it.

Failure to connect to an appropriate AC outlet may cause a fire,

electric shocks, or malfunctions.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it. Failure to observe this may

cause a fire or electric shocks.

• When setting up the unit, make sure that the AC outlet you are

using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power switch and disconnect

the plug from the AC outlet. Even when the power switch is

turned off, as long as the power cord is not unplugged from the

wall AC outlet, the unit will not be disconnected from the

power source.

• If you hear thunder or suspect approaching lightning, quickly

turn off the power switch and pull the power plug from the AC

outlet. Failure to observe this may cause a fire or malfunctions.

• If not using the unit for long periods of time, be sure to pull the

power plug from the AC outlet. Failure to observe this may

cause a fire or malfunctions.

Do not disassemble

• Do not disassemble or modify this unit. Failure to observe this

may cause a fire, electric shocks, injury, or malfunctions. If you

notice any irregularities, be sure to request an inspection or

repair from the dealer where you purchased the unit or from

qualified Yamaha service personnel.

Water warning

• Do not expose the unit to rain, use it near water or in damp or

wet conditions, or place on it any containers (such as vases,

bottles or glasses) containing liquids which might spill into any

openings or places where water may drop. A liquid such as

water getting into the unit may cause a fire, electric shocks, or

malfunctions. If any liquid such as water seeps into the device,

turn off the power immediately and unplug the power cord from

the AC outlet. Then, request an inspection from the dealer

where you purchased the unit or from qualified Yamaha service

personnel.

• Never insert or remove an electric plug with wet hands. Do not

handle this unit with wet hands. Failure to observe this may

cause electric shocks or malfunctions.

Fire warning

• Do not place any burning items or open flames near the unit,

since they may cause a fire.

Installation

• Install in the manner instructed in the manual. Falling or

toppling may result in injury or damage.

• Confirm that the finished installation is safe and secure. Also,

carry out safety inspections periodically. Failure to observe this

may cause devices to fall and result in injury.

Maintenance and care

• Do not use aerosols or spray-type chemicals that contain

combustible gas for cleaning or lubrication. The combustible

gas will remain inside the unit, which may cause explosion or

fire.

Wireless unit

• Do not use this unit near medical devices or inside medical

facilities. Radio waves from this unit may affect electro-

medical devices.

• Do not use this unit within 15 cm (6 in) of persons with a heart

pacemaker implant or a defibrillator implant. Radio waves from

this unit may affect electro-medical devices, such as a heart

pacemaker implant or defibrillator implant.

If you notice any abnormality

• If any of the following abnormalities occur, immediately turn

off the power and disconnect the power plug.

– The power cord/plug is damaged.

– An unusual smell or smoke is emitted from the unit.

– Foreign material gets into the interior of the unit.

– There is a loss of sound during use.

– There is a crack or damage in the unit.

Continued use could cause electric shocks, a fire, or

malfunctions. Immediately request an inspection or repair from

the dealer where you purchased the unit or from qualified

Yamaha service personnel.

• Be careful not to drop or apply strong impact to this unit. If you

suspect the unit may have been damaged due to dropping or

impact, immediately turn off the power and pull the power plug

from the AC outlet. Failure to observe this may cause electric

shocks, a fire, or malfunctions. Immediately request an

inspection from the dealer where you purchased the unit or from

qualified Yamaha service personnel.

• Be sure to request inspections or repairs from the dealer

where you purchased the unit or from qualified Yamaha

service personnel.

• Yamaha cannot be held responsible for injury to you or

damage of the products caused by improper use or

modifications to the unit.

• This product is for ordinary homes. Do not use for

applications requiring high reliability, such as managing

lives, health care or high-value assets.

3 En

English

CAUTION

This content indicates “risk of injury.”

Power supply/power cord

• Do not use an AC outlet where the power plug fits loosely when

inserted. Failure to observe this may cause a fire, electric

shocks, or burns.

• When removing the electric plug from the unit or an AC outlet,

always hold the plug itself and not the cord. Pulling by the cord

can damage it and cause electric shocks or a fire.

• Insert the power plug firmly all the way into the AC outlet.

Using the unit when it is not plugged in sufficiently can cause

dust to accumulate on the plug, causing a fire or burns.

Installation

• Do not place the unit in an unstable position where it might

accidentally drop or fall over and cause injuries.

• Do not block this unit's ventilation holes (cooling slits). This

unit has ventilation holes on the rear to prevent the internal

temperature from becoming too high. Failure to observe this

may trap heat inside the unit, causing a fire or malfunctions.

• When installing this unit:

– Do not cover it with any cloth.

– Make sure the top surface faces up; do not install on its sides

or upside down.

– Do not use the device in a confined, poorly-ventilated

location.

Failure to observe the above may trap heat inside the unit,

causing a fire or malfunctions. Ensure that there is adequate

space around the unit: at least 20 cm (7-7/8 in) on top, 20 cm (7-

7/8 in) on the sides, and 20 cm (7-7/8 in) on the rear.

• Do not install the unit in places where it may come into contact

with corrosive gases or salt air or places that have excessive

smoke or steam. Doing so may result in malfunction.

• Avoid being near the unit during a disaster, such as an

earthquake. Since the unit may turn over or fall and cause

injury, quickly move away from the unit and go to a safe place.

• Before moving this unit, be sure to turn off the power switch

and disconnect all connection cables. Failure to observe this

may damage the cables or cause you or someone else to trip

and fall.

• When transporting or moving the unit always use two or more

people. Attempting to lift the unit by yourself may damage your

back, result in other injury, or cause damage to the unit itself.

Hearing loss

• Do not use the unit/speakers or headphones for a long period of

time at a high or uncomfortable volume level, since this can

cause permanent hearing loss. If you experience any hearing

loss or ringing in the ears, consult a physician.

• Before connecting the unit to other devices, turn off the power

for all devices. Failing to do so may result in hearing loss,

electric shock, or device damage.

Maintenance

• Remove the power plug from the AC outlet before cleaning the

unit. Failure to observe this may cause electric shocks.

Handling

• Do not insert your hand or fingers into panel slits of this unit.

Failure to observe this may cause injury.

• Do not insert foreign materials such as metal or paper into panel

slits of this unit. Failure to observe this may cause a fire,

electric shocks, or malfunctions. If foreign material gets into the

unit, immediately shut off the power and pull the power plug

from the AC outlet and request an inspection from the dealer

where you purchased the unit or from qualified Yamaha service

personnel.

• Do not do the following:

– stand on or sit on the equipment.

– put heavy items on top of the equipment.

– place the equipment in a stack.

– apply unreasonable force to buttons, switches, input/output

terminals, etc.

• Avoid pulling the connected cables to prevent injuries or

damage to the unit by causing it to fall.

• Do not operate the unit if the sound is distorting. Prolonged use

in this condition could cause overheating and result in fire.

Notice

Indicates points that you must observe in order to

prevent product failure, damage or malfunction and

data loss.

Power supply/power cord

• If not using the unit for a long period of time, be sure to pull the

power plug from the outlet. Even if the [(A)] (Standby/On)

switch has been turned off (the power light is off), a minute

current is still flowing.

Installation

• Do not use this unit in the vicinity of other electronic

equipment, such as a TV, radio, or mobile phone. Failure to

observe this may cause this unit or the TV or radio to produce

noise.

• Do not use this unit in a location that is exposed to direct

sunlight that becomes extremely hot, such as near a heater, or

extremely cold, or that is subject to excessive dust or vibration.

Failure to observe this may cause the unit's panel to become

deformed, the internal components to malfunction, or for

operation to become unstable.

• Install this unit as far away from other electronic equipment as

possible.

Digital signals from this unit may interfere with other electronic

equipment.

• If using a wireless function, avoid installing this unit near metal

walls or desks, microwave ovens, or other wireless network

devices. Obstructions could shorten the transmission distance.

Connections

• If connecting external units, be sure to thoroughly read the

manual for each unit and connect them in accordance with the

instructions.

Failure to properly handle a unit in accordance with the

instructions could cause malfunctions.

Handling

• Do not place vinyl, plastic, or rubber products on this unit.

Failure to observe this may cause discoloration or deformation

in the panel of this unit.

• If the ambient temperature changes drastically (such as during

unit transportation or under rapid heating or cooling) and there

is a chance condensation may have formed in the unit, leave the

unit for several hours without turning on the power until it is

completely dry before use. Using the unit while there is

condensation can cause malfunctions.

4 En

Maintenance

• If the temperature or humidity changes drastically, water

droplets (condensation) may form on the unit surface. If water

droplets form, immediately wipe them off with a soft cloth. If

water droplets are left on the unit, they may be absorbed into the

wooden parts, causing deformation.

• When cleaning the unit, use a dry, soft cloth. Using chemicals

such as benzine or thinner, cleaning agents, or chemical

scrubbing cloths can cause discoloration or deformation.

Speakers

• Do not touch the speaker units. Failure to observe this may

damage the speaker units.

Information

About functions and data included in the

unit

• Air may be blown out from the bass reflex port. This is not a

malfunction. This occurs particularly often when outputting

music with heavy bass.

• VOLTAGE SELECTOR (Asia and General models only)

The voltage selector switch on the rear panel of this unit must be

set to your local main voltage BEFORE plugging this unit into

the AC main supply. Voltages are 110-120/220-240 V AC, 50/

60 Hz.

(rear_en_01)

About content in this manual

• The illustrations and screens in this manual are for instructional

purposes only.

• The company names and product names in this manual are the

trademarks or registered trademarks of their respective

companies.

• Software may be revised and updated without prior notice.

Wireless communication functions

[U.K. and Europe models]

Wi-Fi (2.4 GHz)

Radio Frequency: 2402 MHz to 2482 MHz

Maximum Output Power (EIRP): 19.98 dBm

Wi-Fi (5 GHz)

Radio Frequency, Maximum Output Power (EIRP):

5170 to 5250 MHz, 22.30 dBm

5250 to 5330 MHz, 22.27 dBm

5490 to 5710 MHz, 24.56 dBm

5735 to 5835 MHz, 13.96 dBm

• Wireless devices transmitting over a 5 GHz frequency band can

only be used indoors. Use of such devices outdoors is

prohibited by law.

This unit’s speakers use magnets. Do not place items that are

sensitive to magnetism, such as CRT-type TVs, clocks, credit

cards, floppy disks, etc., on or beside this unit.

Wireless devices transmitting over a 5 GHz frequency band can

only be used indoors. Use of such devices outdoors is

prohibited by law.

The model number, serial number, power requirements, etc.,

may be found on or near the name plate, which is at the rear of

the unit. You should note this serial number in the space

provided below and retain this manual as a permanent record of

your purchase to aid identification in the event of theft.

Model No.

Serial No.

Information for users on collection and disposal of

old equipment:

This symbol on the products, packaging, and/or

accompanying documents means that used

electrical and electronic products should not be

mixed with general household waste.

For proper treatment, recovery and recycling of

old products, please take them to applicable

collection points, in accordance with your

national legislation.

By disposing of these products correctly, you will

help to save valuable resources and prevent any

potential negative effects on human health and

the environment which could otherwise arise

from inappropriate waste handling.

For more information about collection and

recycling of old products, please contact your

local municipality, your waste disposal service or

the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic

equipment, please contact your dealer or supplier

for further information.

Information on Disposal in other Countries

outside the European Union:

This symbol is only valid in the European Union.

If you wish to discard these items, please contact

your local authorities or dealer and ask for the

correct method of disposal.

5 En

English

FEATURES................................................................. 5

What you can do using this unit .................................... 5

Advanced Yamaha Active Servo Technology II ............ 7

Twisted Flare Port .......................................................... 7

PARTS AND THEIR FUNCTIONS ............................. 8

Rear panel..................................................................... 8

Top panel ...................................................................... 9

GETTING READY..................................................... 10

Placement ................................................................... 10

CONNECTIONS........................................................ 11

Connecting to a network.............................................. 12

Making analog connections......................................... 15

Adjusting the volume balance ..................................... 15

OPTION SETTINGS.................................................. 16

Updating the firmware ................................................. 16

Initializing all settings (factory reset).............................17

APPENDIX ................................................................ 17

STATUS indicator operation table ............................... 17

TROUBLESHOOTING .............................................. 18

TRADEMARKS......................................................... 20

SPECIFICATIONS..................................................... 21

This unit is a network subwoofer that can be wirelessly connected to MusicCast Surround/Stereo compatible

devices.

When reading this manual, please note the following.

● Specifications and appearance are subject to change without notice in order to improve the product.

● Symbols used in this document

-“ WARNING” indicates information that you must observe to avoid risk of death or serious injury.

-“ CAUTION” indicates information that you must observe to avoid risk of injury.

- “ ” indicates information that you must observe to prevent the product from malfunctioning or being damaged,

or data from being lost.

- “ ” indicates supplementary information that you will find useful.

If you install the dedicated “MusicCast CONTROLLER” app on your smartphone or tablet, you’ll be able to add this unit

to a MusicCast network, allowing easy playback of low-frequency sound of MusicCast Surround/Stereo compatible

devices.

● Wireless connection allows flexible installation

You’ll be free to place the unit where you like, without the annoyance of making cable connections with external

equipment.

● Enjoy optimal ultra-low-frequency sound at all times

The low-frequency range (crossover frequency) and volume balance are automatically adjusted as appropriate for the

MusicCast Surround/Stereo compatible device that you’re using, ensuring that the sound transitions naturally.

● Linked operation for power and volume

The power and volume are linked between this unit and the MusicCast Surround/Stereo compatible units that are paired

with it.

● Twisted Flare Port smoothly reproduces ultra-low-frequency sound

A flared port that twists as it spreads disperses the air turbulence that occurs near the opening of the port, ensuring

smooth airflow. This suppresses noise that is not included in the original input signal, allowing clear low-frequency

sound to be reproduced.

CONTENTS

INTRODUCTION

About this manual

FEATURES

What you can do using this unit

NOTICE

NOTE

FEATURES

6 En

Advanced use with the convenient app (MusicCast CONTROLLER)

“MusicCast CONTROLLER” is a free dedicated app for operating MusicCast compatible devices.

You can use a smartphone or other mobile device as a remote control, and easily select songs or make

settings on a MusicCast compatible device.

For details, search for “MusicCast CONTROLLER” on the App Store or Google Play™.

By using MusicCast, you can share music with other MusicCast compatible devices that are located in multiple rooms.

Music from a mobile device, media server (PC or NAS), internet radio, or streaming service can be enjoyed anywhere in

your home with simple operation.

For details on MusicCast and compatible devices, refer to the following website.

http://www.yamaha.com/musiccast/

In order to connect this unit to a network and use it, you’ll need the “MusicCast CONTROLLER” mobile device

app.

Install MusicCast CONTROLLER on your mobile device.

(→ p. 13 “Downloading the “MusicCast CONTROLLER” mobile device app”)

Internet

Modem

Mobile device

Router

NS-NSW100

PC

NAS

MusicCast Surround/Stereo

compatible devices

FEATURES

7 En

English

In 1988, Yamaha brought to the marketplace speaker systems utilizing YST (Yamaha Active Servo Technology) to give

powerful, high quality bass reproduction. This technique uses a direct connection between the amplifier and speaker,

allowing accurate signal transmission and precise speaker control.

As this technology uses speaker units controlled by

the negative impedance drive of the amplifier and

resonance generated between the speaker cabinet

volume and port, it creates more resonant energy

(the “air woofer” concept) than the standard bass

reflex method. This allows for bass reproduction

from much smaller cabinets than was previously

possible.

Yamaha’s newly developed Advanced YST II adds

many refinements to Yamaha Active Servo

Technology, allowing better control of the forces

driving the amplifier and speaker. From the

amplifier’s point of view, the speaker impedance

changes depending on the sound frequency. Yamaha

developed a new circuit design combining negative-

impedance and constant-current drives, which

provides a more stable performance and clear bass

reproduction, without any murkiness.

Today’s bass reflex speakers use a Helmholtz resonator to improve their

bass reproduction.

However when reproducing bass that is in the frequency region of this

Helmholtz resonator, air moves violently in and out through the port

between the interior and exterior of the speaker, sometimes producing

noise due to the turbulent air flow at the end of the port.

The port and the cabinet resonate at a frequency that is determined by their

dimensions and shape. On the other hand, turbulence in the air flow at the

end of the port contains a broad range of frequency components that are not

present in the input signal. This noise occurs because the broad range of

frequency components includes components that match the resonant

frequencies of the port and cabinet, causing strong resonance.

The Twisted Flare Port developed by Yamaha changes the

way in which the port widens toward its end, and also adds

a “twist” to suppress airflow turbulence at each end of the

port and thus prevent noise from occurring.

This substantially reduces the “muddy sound” and “wind

noise” that until now have been characteristic of bass

reflex speakers, allowing bass to be reproduced clearly.

Advanced Yamaha Active Servo Technology II

Twisted Flare Port

High-amplitude

heavy bass sound

Port

Cabinet

Advanced impedance

Converter

Active Servo

Processing

Amplifier

(Inaudible) signals of ultra-low amplitude

Air woofer

(Helmholtz resonator)

Signals

Bass sound

(audible sound

pressure radiated

from diaphragm)

Conventional Port

Air turbulence on both ends of the port creates noise

Air turbulence is

produced.

Turbulence is

diffused, air flow

becomes smooth.

Twisted Flare Port

FEATURES

8 En

1 A (STANDBY/ON)

This switches the unit’s power between on and

standby.

2 Service port

This is for service, and is not normally used.

3 CONNECT

This is used for the following operations.

4 WIRELESS switch

This turns the wireless communication functionality

(wireless LAN) on/off.

AUTO:

Wireless communication is on.

OFF:

Wireless communication is off. If connecting the unit

to a network, use a wired connection. (→ p. 12 “If

connecting via a cable”)

5 INPUT switch

This switches the unit’s type of connection.

NET:

Choose this if you’re connecting the unit to a network.

ANALOG:

Choose this if you’re connecting the unit directly to an

amp or similar device, without connecting to a

network.

6 INPUT (ANALOG) jack

Use this if the INPUT switch is set to ANALOG.

Connect a cable from the amp’s subwoofer jack or line

output jack (such as PRE OUT) to this jack.

(→ p. 12 “If connecting via a cable”)

7 Service ports

These are for service, and are not normally used.

8 NETWORK port

Use a network cable (commercially available) to

connect to your network via a cabled connection.

PARTS AND THEIR FUNCTIONS

Rear panel

13245 867

● Registering this unit on the

MusicCast network

→ p. 13

● Updating the firmware

→ p. 16

● Initializing the settings

(factory reset)

→ p. 17

PARTS AND THEIR FUNCTIONS

9 En

English

1 GAIN knob

This knob adjusts the volume of this unit. Adjust the

volume appropriately for your playback device.

(→ p. 15 “Adjusting the volume balance”)

NOTE

While you’re changing the volume, the color of the

2 STATUS indicator shows the volume setting.

2 STATUS indicator

The color and lit/flashing status of this indicator shows

the input source that is selected or the status of this unit.

(→ p. 17 “STATUS indicator operation table”)

3 Wireless LAN indicator

The lit or flashing state of this indicator shows the

operating status of the wireless network connection.

Top panel

1

2

3

Volume Color of the STATUS indicator

Minimum value Flashing blue

Low – Medium Blue – Purple

Medium – High Purple – Red

Maximum value Flashing red

Auto power standby

If this unit is not operated and no playback occurs for 20

minutes, it automatically enters standby mode.

NOTE

● Thirty seconds before auto power standby occurs, the

STATUS indicator begins flashing, and goes dark

when standby occurs.

● Auto power standby does not operate if you’re using a

MusicCast connection, or if the rear panel INPUT

switch is set to ANALOG.

Network standby

This unit’s network function is enabled even when the

power is in standby mode.

NOTE

When in network standby, the STATUS indicator is lit

orange.

Eco standby mode

When eight hours have elapsed after the network was

disconnected, the unit enters eco standby mode to save

power.

NOTE

When in eco standby mode, the STATUS indicator is

unlit.

With an advanced energy saving design,

this product achieves a low power

consumption of not more than two watts

when in Network Standby mode.

PARTS AND THEIR

FUNCTIONS

10 En

Since the low-end frequencies of audio signals feature long wavelengths, they are almost non-directional to human ears.

The super-bass range does not create a stereo image. Therefore, a single subwoofer may be enough to produce a high-

quality super-bass sound.

NOTICE

● Placing the subwoofer too close to a CRT-type TV may impair the picture color or cause a buzzing noise. In this case,

place the subwoofer and TV at a separated position where these effects do not occur. This is not an issue with LCD and

plasma TVs.

● If the speaker volume is very loud, furniture or window glass may resonate and the subwoofer itself may vibrate. In

this case, lower the volume level. To limit resonance, use a thick curtain or similar cloth that tends to absorb sound

vibrations effectively. Also, changing the subwoofer position may be helpful.

● This unit’s speaker uses magnets. Devices that are affected by magnetism (CRT televisions, clocks, bank cards, etc.)

must not be placed on or near this unit.

GETTING READY

Placement

A

or

( : Subwoofer : Front speaker)

B

or

Note

The placement shown in the

figure on the right is also

possible. However, if the

subwoofer system is placed

directly facing a wall, the bass

effect may suffer due to phase

cancellation caused by the

interference between the

direct and reflected sounds.

To prevent this from

happening, place the

subwoofer system at an angle.

(Figures and )

NOTICE

There may be a case

that you cannot obtain

enough super-bass

sound from the

subwoofer due to

standing waves.

A

B

11 En

English

If using with a network connection

If using without connecting to a network (analog connection)

CONNECTIONS

Modem

Mobile device

Router

MusicCast Surround/Stereo compatible

sound bar, wireless streaming speaker, etc.

NS-NSW100

PC

Internet

Wireless connection ( p. 12)

AV 7

LAN

WAN

Internet

Modem

Mobile device

Router

Network cable

NAS

NS-NSW100

(rear panel)

PC

MusicCast Surround/Stereo compatible

sound bar, wireless streaming speaker, etc.

STP network cable

(commercially available

CAT-5 or higher straight

cable)

Wired connection ( p. 12)

NS-NSW100

(rear panel)

Sound bar etc. with

ANALOG output jacks

Analog connection ( p. 15)

(Connection example)

3.5 mm

monaural

mini plug

GETTING READY

CONNECTIONS

12 En

Preparations for network connection

This unit can be connected to a network either via a cable or wirelessly. Choose the connection method that’s appropriate

for your situation.

Make settings so that this unit can communicate wirelessly.

1. Set the rear panel INPUT switch to NET.

2. Set the rear panel WIRELESS switch to

AUTO.

NOTICE

Do not connect a network cable to the NETWORK

port. If a network cable is connected, the wired

connection takes priority and wireless connection is

not possible.

Use a commercially available STP network cable (CAT-5

or higher straight cable) to connect this unit to your router.

1. Set the rear panel INPUT switch to NET.

2.

Set the rear panel WIRELESS switch to OFF.

3. Connect a network cable to the

NETWORK port.

NOTICE

If you want to connect this unit via a wired connection

and play back music, all of the MusicCast Surround/

Stereo compatible devices that you want to link (such

as a sound bar or a wireless streaming speaker) must be

connected via a wired LAN.

Powering-on this unit

1. Insert the power cord plug into an AC

outlet.

2. Press the rear panel A (STANDBY/ON)

button to turn on the power of this unit.

NOTE

● If the network is starting up, the STATUS indicator on the top panel flashes green.

● If you’re using a wired connection, the LED on the inside of the NETWORK port flashes when connected to the router.

NOTICE

● When turning on the power in your audio system, always turn on this unit last.

Connecting to a network

If connecting wirelessly

2 1

(rear panel)

If connecting via a cable

3

2

1

(rear panel)

to an AC outlet

(rear panel)

CONNECTIONS

13 En

English

Downloading the “MusicCast CONTROLLER” mobile device app

Install the MusicCast CONTROLLER app on your mobile device, connect this unit to the network, and register this unit

as a MusicCast device.

Search for “MusicCast CONTROLLER” on the Apple Store or Google Play, and install it.

NOTE

● Make sure that the mobile device you’re using is connected to your home’s router before you proceed.

● The screens and menu names etc. of MusicCast CONTROLLER might change without notice.

● If a different MusicCast device is already registered to the MusicCast CONTROLLER app, you can add this unit to

the app by tapping (Settings) in the “Room select” and selecting “Add new device.”

Registering this unit on the MusicCast network

Here’s how to use “MusicCast CONTROLLER” to register this unit on the MusicCast network, and simultaneously make

network connection settings for this unit.

NOTE

To connect wirelessly to the network, you’ll need to have the SSID and security key of the wireless LAN router (access

point) that you’re using.

1. On your mobile device, start “MusicCast

CONTROLLER” and tap “Settings.”

2. From the app’s “Settings,” tap “Add new

device.”

3. As directed by the instructions that

appear in the screen of your mobile

device, operate “MusicCast

CONTROLLER” and on the rear panel of

this unit, hold down CONNECT for 5

seconds or longer.

4. As directed by the instructions that

appear in the screen of your mobile

device, operate “MusicCast

CONTROLLER” to specify the network.

Next, pair this unit with the Pairing Master device of the

MusicCast network. (→ p. 14 “Linking this unit with the

Pairing Master device”)

NOTE

If you use a wireless connection to register this unit on the

MusicCast network, the Wireless LAN indicator of

this unit’s top panel will light, indicated that registration on

the MusicCast network is complete.

(rear panel)

To cancel this unit’s MusicCast network registration

Operate “MusicCast CONTROLLER” to cancel this unit’s registration.

NOTE

If you initialize this unit before canceling the registration, the screen of the “MusicCast CONTROLLER” may show

an error indicated that this device does not exist.

CONNECTIONS

14 En

Linking this unit with the Pairing Master device

By registering this unit as a Pairing Device of the

MusicCastnetwork’s Pairing Master (such as a sound bar or

wireless streaming speaker), you can use it as a network

subwoofer to enjoy richer sound.

1. Register this unit and the MusicCast Surround/Stereo (Pairing Master) compatible unit in

the same location of the MusicCast CONTROLLER app.

→ p.13 “Registering this unit on

the MusicCast network”)

5.

Following the guidance in the app screen, register this unit as a subwoofer (Pairing Device).

When you have finished registering this unit as a Pairing Device, operate the appropriate room (Pairing Master) in the

app screen to play back audio.

■ Linked operation with the Pairing Master

When you register this unit as a network subwoofer, this unit will follow operations of the room (Pairing Master).

Power operation

This unit’s power setting (Standby/ON) will follow operations of the room (Pairing Master).

Volume and other settings

In accordance with the settings of the room (Pairing Master), this unit's settings will also change in order to obtain optimal

low-frequency sound.

Settings that are linked:

• Volume

• High-cut filter (crossover frequency)

NOTE

● If audio is interrupted, check the app to see whether “Link control” located in the room (Pairing Master) settings is

selected as shown below.

– For a wireless connection: other than “Speed Boost”

– For a wired connection: “Speed Boost”

■ To cancel the link with the Pairing Master

On your mobile device, operate “MusicCast CONTROLLER” to cancel the registration.

Pairing Master

(sound bar, etc.)

Pairing Device

(NS-NSW100)

2.

On your mobile device,

start “MusicCast

CONTROLLER” and tap

(settings).

3. Tap “MusicCast

Surround/Stereo.”

4. Select the room (Pairing

Master) with which you

want to link this unit.

CONNECTIONS

15 En

English

Use the ANALOG jack on the rear panel of this unit if you want to connect this unit directly to other devices (such as a

sound bar) without connecting to a network.

1. Connect this unit’s rear panel ANALOG

jack to the subwoofer output jack or line

output jack (e.g., PRE OUT) of the

connected device.

2. Set this unit’s rear panel INPUT switch to

ANALOG.

3. Insert the power cord plug into an AC

outlet.

4. Press the rear panel A (STANDBY/ON)

button to turn on the power of this unit.

NOTICE

● Do not connect the power cord to the AC outlet until all

connections are completed.

● Depending on the device (sound bar, etc.) that you’re

connecting, the connection method and the names of the

jacks might differ from this instructions in this

document, so you should also refer to the owner’s

manual of the respective device.

● When this unit is shipped from the factory, its volume is

set to the minimum setting. When you have finished

making connections, make adjustments so that this unit

produces an appropriate volume.

In order to ensure effective low-frequency playback, you can adjust the volume so that the sound of this unit blends

naturally with the speaker that you’re using.

■ If using a network connection

If this unit is connected to a network, the volume of this

unit is automatically adjusted to match the Pairing Master,

but you can make fine adjustments to your taste by using

the top panel GAIN knob.

Default value: Depends on the setting of the Pairing

Master

■ If using an analog connection

Use the top panel GAIN knob to adjust the volume of this

unit.

High-cut filter frequency: fixed at 160 Hz

Default value: MUTE

Making analog connections

NS-NSW100

(rear panel)

3.5 mm

monaural

mini plug

Sound bar etc. with

ANALOG output jacks

(Connection example)

Adjusting the volume balance

GAIN knob

(top panel)

CONNECTIONS

16 En

If this unit is connected to a network, the firmware can be updated via the network. When new firmware is available, the

STATUS indicator flashes white when the power of this unit turns on. Use the following procedure to update the firmware.

NOTICE

Observe the following points during the update.

- Do not operate this unit

- Do not disconnect the power cord or the network cable

Firmware update procedure

1. On the rear panel, press A (STANDBY/

ON) to put the unit in standby mode.

2. On the rear panel, hold down CONNECT

for 10 seconds or longer.

The STATUS indicator and the Wireless LAN

indicator on the top panel flash, and the firmware

update begins.

When the indicator changes to steadily lit (orange), the

firmware update is complete.

NOTE

● Firmware update takes about 10 or 20 minutes.

● If the internet connection is not fast enough, or

depending on the connection status of the wireless

network, the firmware update might take longer or might

fail.

● If the firmware update fails, the STATUS indicator

flashes red. Wait a while, and then try the operation

again.

■ Checking the firmware version

Here’s how you can check the version of the firmware

that’s installed in this unit.

1. On the rear panel, press A (STANDBY/

ON) to put the unit in standby mode.

2. On the rear panel, press CONNECT.

The STATUS indicator and the Wireless LAN

indicator on the top panel flash a number of times to

indicate the firmware version. For example if the

firmware version is 1.3, the STATUS indicator flashes

once and the Wireless LAN indicator flashes

three times.

NOTE

If the firmware version is 2.0, the STATUS indicator

flashes twice and the Wireless LAN indicator

remains unlit.

3. Press CONNECT once again to return to

standby mode.

OPTION SETTINGS

Updating the firmware

(rear panel)

Major version

(flash yellow)

Minor version

(flash)

(top panel)

APPENDIX

17 En

English

1. On the rear panel, press A (STANDBY/

ON) to put the unit in standby mode.

2. While holding down CONNECT, press

A (STANDBY/ON) once.

3. When the STATUS indicator flashes,

release CONNECT.

The color and lit/flashing state of the indicators shows the status of this unit.

NOTE

● The STATUS indicator and the Wireless LAN indicator can be used to check the firmware version of this unit.

(→ p. 16 “Checking the firmware version”)

● While the firmware is being updated, the STATUS indicator and the Wireless LAN indicator can be used to check

the progress. (→ p. 16 “Firmware update procedure”)

When the power is on

When in standby mode

Initializing all settings (factory reset)

(rear panel)

1

2

(top panel)

APPENDIX

STATUS indicator operation table

Indicator Status

Green Lit The rear panel INPUT switch is set to NET.

White Lit The rear panel INPUT switch is set to ANALOG.

Green Flashing Waiting to connect to the network.

White Flashing New firmware is available.

Green/Orange

Flashing

alternately

The auto power standby function will soon put the unit in standby mode. (Starts

flashing 30 seconds beforehand.)

White/Orange

Orange Lit The unit is in network standby mode.

Blue/Purple/Red

Lit

The unit’s volume is being changed.

Blue: low volume – Purple: medium – Red: high volume

Blue/Red Flashing The volume was set to minimum or maximum.

Indicator Status

Orange Lit The unit is in network standby mode.

– Unlit The unit’s power is off or in eco standby mode.

Orange Flashing

The protection circuit has operated. Turn off the power of the unit, disconnect the

power plug from the AC outlet, and contact a Yamaha service center.

APPENDIX

OPTION

SETTINGS

18 En

Refer to the chart below if this unit does not function properly. If the problem you are experiencing is not listed below or

if the instructions given below do not help, turn off the power to the unit, disconnect the power plug from the AC outlet,

and contact an authorized Yamaha dealer or service center.

General

TROUBLESHOOTING

Problem Cause What to Do

Power does not turn on.

When the power is turned on, it

turns off immediately.

The unit does not operate correctly.

The power cord is not connected correctly. Insert the power plug firmly into the AC outlet.

The unit cannot be operated. Electric shock (such as a lightning strike or

excessive static electricity) or power supply

voltage drop has caused the internal

microcomputer to freeze.

Hold down the unit’s rear panel

A (STANDBY/ON) button for ten seconds or

longer to restart the unit.

(If this does not solve the problem, disconnect

the power cord from the AC outlet, wait

approximately 30 seconds, and then plug it in

once again.)

The power suddenly turns off

during use.

The protection circuit has operated to turn off

the power because the internal temperature of

the unit has risen.

Wait for the temperature to cool

(approximately one hour), make sure that there

is sufficient space around the unit and that the

unit is not covered by a cloth etc., and then turn

on the power again.

The unit does not operate correctly. External electric shock (such as a lightning

strike or excessive static electricity) or power

supply voltage drop has caused the internal

microcomputer to freeze.

Disconnect the power cord from the AC outlet,

wait approximately 30 seconds, and then plug

it in once again.

No sound.

Low-frequency sound is not output

or is not loud enough.

A source with little low-frequency sound is

being played back.

Play back a source that contains low-frequency

sound.

The sound is being affected by a standing

wave.

Try changing the position or the angle of this

unit.

Low-frequency input signal is absent because

of settings on the amp.

Change the amp’s settings.

If using a network connection

The volume of the MusicCast CONTROLLER

app or of the Pairing Master is set to the

minimum (0). Alternatively, headphones are

connected to the Pairing Master.

Raise the volume by operating the MusicCast

CONTROLLER app or the Pairing Master.

You can also use this unit’s GAIN knob to

manually make fine adjustments to the volume.

The network connection is not correct. Check the connection.

The playback device is not selected correctly. Operate the MusicCast CONTROLLER app or

the Pairing Master to re-select the input source

that you want to play back.

If using an analog connection

The volume of this unit is set to the minimum

(0).

Use this unit’s GAIN knob to adjust the

volume.

The connection is not correct. Alternatively,

the connection is faulty.

Check the connection.

The power does not turn on

automatically when the source

begins playing.

Since INPUT is set to ANALOG, the unit is not

operating in linkage with the Pairing Master.

Turn on the power manually.

Low-frequency input signal is absent because

of settings on the amp.

Change the amp’s settings.

Because there was no network connection for

an extended time, the unit entered eco standby

mode.

Turn on the power manually.

Noise is output from this unit or

from an electronic device located

nearby.

A digital device or a high-frequency device is

located near this unit.

Move this unit and the corresponding device

farther apart.

TROUBLESHOOTING

19 En

English

Network

Problem Cause What to Do

Network functionality cannot be

used.

Network information (IP address) has not been

obtained correctly.

Enable the DHCP server function of your

router.

Can’t connect to the wireless LAN

router (access point).

MAC address filtering is enabled on the

wireless LAN router (access point).

Connection is not possible if MAC address

filtering is enabled. Change the settings of the

wireless LAN router (access point) so that

connection can occur.

Can’t connect to the internet via

the wireless LAN router (access

point).

The wireless LAN router (access point) is

powered-off.

Power-on the wireless LAN router (access

point).

The wireless LAN router (access point) and

this unit are too far apart.

Locate the wireless LAN router (access point)

and this unit closer together.

There is an obstacle between the wireless LAN

router (access point) and this unit.

Locate the wireless LAN router (access point)

and this unit where there is no obstacle

between them.

This unit is not detected by the

MusicCast CONTROLLER app.

This unit and the mobile device are not

connected to the same network.

Check the network connections and the router

settings, and connect them to the same

network.

The wireless network cannot be

found.

A device that generates electromagnetic

radiation (such as a microwave oven or radio

equipment) is located nearby.

If using this unit with a wireless connection, do

not use it near a device that generates

electromagnetic radiation.

Access to the network is being restricted by the

firewall settings of the wireless LAN router

(access point).

Check the firewall settings of the wireless LAN

router (access point).

Can’t make connection settings

using the MusicCast

CONTROLLER app.

The mobile device is not connected to the

wireless LAN router (access point).

Connect the mobile device to the wireless LAN

router, and then use the MusicCast

CONTROLLER app to make settings.

You’re using a router that has multi-SSID

support.

The router’s network separation function might

be making it impossible to access this unit.

When connecting a mobile device, use an SSID

that allows access to this unit (try connecting to

the primary SSID).

Failed to update the firmware via

the network.

The state of the network connection is not

good.

Wait a while, and then try updating again.

Can’t connect with the Pairing

Master.

The Pairing Master is not a MusicCast

Surround/Stereo compatible device.

Use a MusicCast Surround/Stereo compatible

device, or a device that allows analog

connections.

The connection is not correct. Alternatively,

the connection is faulty.

After initializing this unit, check that the

Pairing Master is a MusicCast Surround/Stereo

compatible unit, and then connect again.

Pairing with another device has already been

registered.

Cancel the registered pairing with that device,

and make the registration settings again.

TROUBLE-

SHOOTING

20 En

Android™

Google Play™

Android and Google Play are trademarks of Google LLC.

The Wi-Fi CERTIFIED™ Logo is certification mark of Wi-Fi

Alliance

®

.

Wi-Fi, Wi-Fi CERTIFIED and WPA2 are registered trademarks or

trademarks of Wi-Fi Alliance

®

.

MusicCast is a trademark or registered trademark of Yamaha

Corporation.

Yamaha Eco-Label is a mark that certifies products of high

environmental performance.

TRADEMARKS

Licenses

For information on the licenses of the third-party software in

this product, refer to the following.

http://(IP address of this product*)/licenses.html

* IP address of this product is checked with MusicCast

CONTROLLER.

Explanations regarding GPL

This product utilizes GPL/LGPL open-source software in some

sections.

You have the right to obtain, duplicate, modify, and redistribute

this open-source code only.

For information on GPL/ LGPL open source software, how to

obtain it, and the GPL/LGPL license, refer to the Yamaha

Corporation website

(http://download.yamaha.com/sourcecodes/musiccast/).

Sayfa yükleniyor ...

Yamaha NSNSW100PB SUB 100 BK El kitabı

Bu kılavuz için de uygundur

Yamaha NSNSW100PB SUB 100 BK El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler