Samsung DVD-H1080 Kullanım kılavuzu

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive more complete service, please register

your product at

www.samsung.com/global/register

DVD Player

user manual

DVD-H1080

DVD-H1080R

DVD-H1080W

AK68-01755P

precautions

2_ precautions

before you

start

Install Batteries in the Remote con-

trol

If remote control doesn’t operate

properly:

- Check the polarity + - of the batteries.

- Check if the batteries are drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Accessories

1. Open the battery cover on the back of the remote

control.

2. Insert two AAA batteries.

Make sure that the

polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

1. Setting up

- Refer to the identification label located on

the rear of your player for its proper operat-

ing voltage.

- Install your player in a cabinet with ade-

quate ventilation holes. (7~10cm) Do not

block ventilation holes on any of the compo-

nents for air circulation.

- Do not push the disc tray in by hand.

- Do not stack components.

- Be sure to turn all components off before

moving the player.

- Before connecting other components to this

player, be sure to turn them off.

- Be sure to remove the disc and turn off the

player after use, especially if you are not

going to use it for a long time.

- The main plug is used as a disconnect

device and shall stay readily operable at

any time.

2. For your safety

- This product utilizes a laser. Use of controls

or adjustments or performance of proce-

dures other than those specified herein may

result in hazardous radiation exposure.

- Do not open covers and do not repair your-

self. Refer servicing to qualified personal.

3. Caution

- Your player is not intended for industrial use

but for domestic purposes. Use of this prod-

uct is for personal use only.

- Apparatus shall not be exposed to dripping

or splashing and no object filled with liquids,

such as vases, shall be placed on the appa-

ratus.

- Exterior influences such as lightning and

static electricity can affect normal operation

of this player. If this occurs, turn the player

off and on again with the POWER button,

or disconnect and then reconnect the AC

power cord to the AC power outlet. The

player will operate normally.

- When condensation forms inside the player

due to sharp changes in temperature, the

player may not operate correctly. If this

occurs, leave the player at room tempera-

ture until the inside of the player becomes

dry and operational.

4. Disc

- Do not clean disc using record-cleaning

sprays, benzene, thinner, or other volatile

solvents that may cause damage to the disc

surface.

- Do not touch the disc’s signal surface. Hold

by the edges or by one edge and the hole

in the center.

- Wipe the dirt away gently; never wipe a

cloth back and forth over the disc.

5. Environmental info

- The battery used in this product contains

chemicals that are harmful to the environ

ment.

- So, dispose of batteries in the proper man

ner, according to federal, state, and local

regulations.

The product unit accompanying this user manual

is licensed under certain intellectual property rights

of certain third parties. This license is limited to

private non-commercial use by end-user consum-

ers for licensed contents. No rights are granted

for commercial use. The license does not cover

any product unit other than this product unit and the

license does not extend to any unlicensed product

unit or process conforming to ISO/OUR 11172-3 or

ISO/OUR 13818-3 used or sold in combination with

this product unit. The license only covers the use of

this product unit to encode and/or decode audio files

conforming to the ISO/OUR 11172-3 or ISO/OUR

13818-3. No rights are granted under this license for

product features or functions that do not conform to

the ISO/OUR 11172-3 or ISO/OUR 13818-3.

CAUTION: USE OF ANY CONTROLS,

ADJUSTMENTS, OR PROCEDURES OTHER

THAN SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

English _3

before you

start

table of

content

Install Batteries in the Remote con-

trol

If remote control doesn’t operate

properly:

- Check the polarity + - of the batteries.

- Check if the batteries are drained.

- Check if remote control sensor is blocked by

obstacles.

- Check if there is any fluorescent lighting nearby.

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Setup

General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4

Disc Type and Characteristics . . . . . . . . . . . . . . . .5

Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Tour of the Remote Control. . . . . . . . . . . . . . . . . . .7

Connections

Choosing a Connection . . . . . . . . . . . . . . . . . . . . .8

Basic Functions

Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Using the Search and Skip Functions . . . . . . . . .16

Using the Display Function . . . . . . . . . . . . . . . . .16

Using the Disc and Title Menu . . . . . . . . . . . . . . .17

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Advanced Functions

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .18

Selecting the Audio Language . . . . . . . . . . . . . . .18

Selecting the Subtitle Language . . . . . . . . . . . . . .19

Changing the Camera Angle . . . . . . . . . . . . . . . . .19

Using the Bookmark Function . . . . . . . . . . . . . . . .20

Using the Zoom Function . . . . . . . . . . . . . . . . . . .20

Clips Menu for MP3/WMA/JPEG/MPEG4/

CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .21

MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .21

MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .22

Playing media files Using the USB

Host Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .25

Picture CD Playback for HD-JPEG . . . . . . . . . . . .26

Changing Setup Menu

Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . .27

Setting Up the Language Features . . . . . . . . . . . .27

Setting Up the Audio Options . . . . . . . . . . . . . . . .28

Setting Up the Display Options . . . . . . . . . . . . . . .29

Setting Up the Parental Control . . . . . . . . . . . . . .30

Setting Up the HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Reference

Firmware upgrade . . . . . . . . . . . . . . . . . . . . . . . . .35

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .36

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Accessories

Remote Control

Batteries for Remote

Control (AAA Size)

1. Open the battery cover on the back of the remote

control.

2. Insert two AAA batteries.

Make sure that the

polarities (+ and -) are aligned correctly.

3. Replace the battery cover.

User’s Manual

Video/Audio

Cable

HDMI Cable

setup

4_ setup

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduc-

tion.

Screen

Both regular and widescreen(16:9) pictures can be

viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback

on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level

necessary to prohibit children from viewing harmful

movies such as those with violence, adult subject

matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional inter-

laced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match

your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing

the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA

files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping

This features lets you to copy audio files from disc

to USB device into MP3 format. (Only Audio CD

(CD DA)).

HDMI (High Definition Multimedia

Interface)

HDMI reduces picture noise by allowing a pure

digital video/audio signal path from the player to

your TV.

Note

- Discs which cannot be played with this

player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW

and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD

player directly to your TV, not to a VCR. Connecting

to a VCR results in a distorted picture from copy-

protected DVD discs.

This product incorporates copyright protection

technology that is protected by methods claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision Corporation. Reverse engi-

neering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(576p,720p,1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE, IF PROGRESSIVE SCAN PICTURE

PROBLEMS OCCUR, IT IS RECOMMENDED

THAT THE USER SWITCH THE CONNECTION

TO THE ‘STANDARD DEFINITION’ OUTPUT. IF

THERE ARE QUESTIONS REGARDING YOUR TV

SET COMPATIBILITY WITH THIS DVD PLAYER,

PLEASE CONTACT SAMSUNG'S CUSTOMER

SERVICE CENTER.”

General Features

setup

English _5

● SETUP

This DVD player is capable of playing the following types of discs with the corresponding logos:

Disc Markings

Region Number

Both the DVD player and the discs are coded

by region. These regional codes must match

in order for the disc to play. If the codes do not

match, the disc will not play.

The Region Number for this player is

described on the bottom panel of the player.

You must only insert one DVD disc at a time.

Inserting two or more discs will not allow to

play them back and it may cause damage to

the DVD player.

12 Cm

8 Cm

Single-sided 240 min.

Double-sided 480 min.

Single-sided 80 min.

Double-sided 160 min.

Audio

+

Video

- DVD contains excellent sound and

video due to Dolby Digital and MPEG-

2 system.

- Various screen and audio functions

can be easily selected through the on-

screen menu.

Disc Types (Logos)

Recording Types Disc Size Max. Playing Time Characteristics

DVD

12 Cm

8 Cm

74 min.

20 min.

Audio

+

Video

- Video with CD sound, VHS quality &

MPEG-1 compression technology.

VIDEO-CD

12 Cm

8 Cm

74 min.

20 min.

Audio

- CD is recorded as a Digital Signal

with better audio quality, less distor-

tion and less deterioration of audio

quality over time.

AUDIO-CD

STEREO

~

DIGITAL

SOUND

STEREO

PAL

Play Region Number

PAL broadcast system in U.K, France,

Germany, etc.

Dolby Digital disc

Stereo disc

Digital Audio disc

DTS disc

MP3 disc

DivX Certification

DivX, DivX Certified,

and associated logos are trademarks of

DivXNetworks, Inc and are used under

license

Disc Type and Characteristics

Excellent Sound

Dolby Digital, a technology developed by Dolby

Laboratories, provides crystal clear sound reproduc-

tion.

Screen

Both regular and widescreen(16:9) pictures can be

viewed.

Slow Motion

An important scene can be viewed in slow motion.

1080p Playback

This player upconverts regular DVDs for playback

on 1080p TVs.

Parental Control (DVD)

The parental control allows users to set the level

necessary to prohibit children from viewing harmful

movies such as those with violence, adult subject

matter, etc.

Various On-Screen Menu Functions

You can select various languages (Audio/Subtitle)

and screen angles while enjoying movies.

Progressive Scan

Progressive scanning creates an improved picture

with double the scan lines of a conventional inter-

laced picture.

EZ VIEW (DVD)

Easy View enables picture adjustment to match

your TV's screen size (16:9 or 4:3).

Digital Photo Viewer (JPEG)

You can view Digital Photos on your TV.

Repeat

You can repeat a song or movie simply by pressing

the REPEAT button.

MP3/WMA

This unit can play discs created from MP3/WMA

files.

MPEG4

This unit can play MPEG4 formats within an avi file.

CD Ripping

This features lets you to copy audio files from disc

to USB device into MP3 format. (Only Audio CD

(CD DA)).

HDMI (High Definition Multimedia

Interface)

HDMI reduces picture noise by allowing a pure

digital video/audio signal path from the player to

your TV.

Note

- Discs which cannot be played with this

player.

• DVD-ROM • DVD-RAM

• CD-ROM • CDV

• CDI • CVD

• CDGs play audio only, not graphics.

- Ability to play back may depend on recording

conditions.

• DVD-R, +R

• CD-RW

• DVD+RW, -RW (V mode)

- The unit may not play certain CD-R, CD-RW

and DVD-R due to the disc type or recording

conditions.

COPY PROTECTION

Many DVD discs are encoded with copy protection.

Because of this, you should only connect your DVD

player directly to your TV, not to a VCR. Connecting

to a VCR results in a distorted picture from copy-

protected DVD discs.

This product incorporates copyright protection

technology that is protected by methods claims of

certain U.S. patents and other intellectual property

rights owned by Macrovision Corporation and other

rights owners. Use of this copyright protection

technology must be authorized by Macrovision

Corporation, and is intended for home and other

limited viewing uses only unless otherwise autho-

rized by Macrovision Corporation. Reverse engi-

neering or disassembly is prohibited.

PROGRESSIVE SCAN OUTPUTS

(576p,720p,1080p)

“CONSUMERS SHOULD NOTE THAT NOT ALL

HIGH DEFINITION TELEVISION SETS ARE FULLY

COMPATIBLE WITH THIS PRODUCT AND MAY

CAUSE ARTIFACTS TO BE DISPLAYED IN THE

PICTURE, IF PROGRESSIVE SCAN PICTURE

PROBLEMS OCCUR, IT IS RECOMMENDED

THAT THE USER SWITCH THE CONNECTION

TO THE ‘STANDARD DEFINITION’ OUTPUT. IF

THERE ARE QUESTIONS REGARDING YOUR TV

SET COMPATIBILITY WITH THIS DVD PLAYER,

PLEASE CONTACT SAMSUNG'S CUSTOMER

SERVICE CENTER.”

setup

6_ setup

Tour of the Remote Control

Description

Front Panel Controls

1. STANDBY/ON ( )

When STANDBY/ON is pressed on, the indicator goes

out and the player is turned on.

2. STANDBY Indicator

When the unit is first plugged in, the indicator lights.

3. DISC TRAY

Place the disc here.

4. OPEN/CLOSE/Stop ( )

Press to open and close the disc tray, Stops disc play.

5. PLAY/PAUSE ( )

Begin or pause disc play.

Rear Panel

1. DIGITAL AUDIO OUT JACKS

- Use coaxial digital cable to connect to a compatible

Dolby Digital receiver.

- Use coaxial digital cable to connect to an A/V

Amplifier that contains a Dolby Digital, MPEG2 or

DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide P

R

, P

B

and Y

video.

- If P-SCAN Video Output is selected in Setup Menu,

progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu,

interlaced scan mode will work.

3. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or

audio/video receiver.

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack

on your television.

5. USB Host

- Connect digital still camera, MP3 player, memory

stick, Card reader, or another removable storage

devices.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI

jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compat

-

ible TV, HDMI will be output automatically within 10

seconds.

setup

English _7

● SETUP

Note

-

Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).

If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in

the TV’s menu system.

- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conver-

sion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input.

- There may be no image output if the DVD player is connected to a TV or display that is not compatible

with the above format.

- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal.

- See pages 29 ~ 30 to get more information on how to use the setup menu.

Tour of the Remote Control

1. DVD Power Button

Turns the power on or off.

2. REPEAT Button

Allows you to repeat play a title, chapter, track or disc

3. DISC MENU Button

Brings up the Disc menu.

4. Bookmark Button

5. SEARCH (

/

) Buttons

Allow you to search forward/backward through a disc.

6. STOP (

) Button

7. SUBTITLE (

π) Button

8. MENU Button

Brings up the DVD player’s menu.

9. AUDIO (√) Button

Use this button to access various audio functions on a disc.

10. ENTER/π/†,√/® Buttons

This button functions as a toggle switch.

11. INFO Button

Displays the current disc mode.

12. OPEN/CLOSE ( ) Button

To open and close the disc tray.

13. REPEAT A-B Butoon

Allows you to repeat play a chosen section (A-B) on a

disc.

14. USB button

15. PAUSE (

) Button

Pause disc play.

16. PLAY ( ) Button

Begin disc play.

17. SKIP (

/

)Buttons

Use to skip the title, chapter or track.

18. RETURN Button

Returns to a previous menu.

19. TITLE MENU (®) Button

Brings up the Title menu.

20. CANCEL Button

Use to remove menus or status displays from the screen.

1

2

3

4

5

8

7

6

10

9

11

12

13

14

15

16

17

18

20

19

1. DIGITAL AUDIO OUT JACKS

- Use coaxial digital cable to connect to a compatible

Dolby Digital receiver.

- Use coaxial digital cable to connect to an A/V

Amplifier that contains a Dolby Digital, MPEG2 or

DTS decoder.

2. COMPONENT VIDEO OUT JACKS

- Use these jacks if you have a TV with Component

Video in jacks. These jacks provide P

R

, P

B

and Y

video.

- If P-SCAN Video Output is selected in Setup Menu,

progressive scan mode will work.

- If I-SCAN Video Output is selected in Setup Menu,

interlaced scan mode will work.

3. AUDIO OUT JACKS

- Connect to the Audio input jacks of your television or

audio/video receiver.

4. VIDEO OUT JACK

- Use a video cable to connect to the Video input jack

on your television.

5. USB Host

- Connect digital still camera, MP3 player, memory

stick, Card reader, or another removable storage

devices.

6. HDMI OUT JACK

- Use the HDMI cable to connect this jack to the HDMI

jack on your television for the best quality picture.

- If an HDMI cable is connected to an HDMI-compat

-

ible TV, HDMI will be output automatically within 10

seconds.

connections

8_ connections

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until

the Component signal from the DVD player appears on the

TV screen.

4

Set the Video Output to I-SCAN in the Display Setup

menu. (See pages 29-30)

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those

particular components.

Connection to a TV (For Video)

1

Using video/audio cables, connect the VIDEO (yellow)/

AUDIO (red and white) OUT terminals on the rear of the

DVD player to the VIDEO (yellow)/AUDIO (red and white)

IN terminals of TV.

2

Turn on the DVD player and TV.

3

Press the input selector on your TV remote control until

the Video signal from the DVD player appears on the TV

screen.

Note

- Noise may be generated if the audio cable is too close to the power cable.

- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)

- The number and position of terminals can vary depending on your TV set. Please refer to the user's

manual of the TV.

- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the

DVD player.

Choosing a Connection

RED

WHITE

YELLOW

RED

WHITE

YELLOW

Audio

Cable

Video Cable

connections

English _9

● CONNECTIONS

Connection to a TV (Interlace)

- Connecting to your TV using Component video cables.

- You will enjoy high quality and accurate color reproduction images. Component video separates the pic

-

ture element into black and white(Y), blue(P

B

), red(P

R

) signals to present clear and clean images. (Audio

signals are delivered through the audio output.)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until

the Component signal from the DVD player appears on the

TV screen.

4

Set the Video Output to I-SCAN in the Display Setup

menu. (See pages 29-30)

Note

- If you want to connect to an Amplifier, please refer to the Amplifier connection page.(See pages 13 to 14)

- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “P

R

, P

B

, Y”

depending on the manufacturer. The number and position of terminals can vary depending on the TV set.

Please refer to the user's manual of the TV.

RED

WHITE

RED

WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

The following shows examples of connections commonly used to connect the DVD player with a TV and

other components.

Before Connecting the DVD Player

- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.

- Refer to the user’s manual of the additional components you are connecting for more information on those

particular components.

Connection to a TV (For Video)

connections

10_ connections

Connecting to a TV with DVI Jack

Connecting to a TV with HDMI Jack

HDMI VIDEO Specifications

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds.

- If you set the HDMI output resolution 720p, 1080i or 1080p, HDMI output provides better picture quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player

using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).

(See page 32)

- If your TV has an logo, then it will Supports the Anynet+ Function.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

1

Using the HDMI-HDMI cable connect the HDMI OUT termi-

nal on the rear of the DVD player to the HDMI IN terminal

of your TV.

Connection to a TV (Progressive)

1

Using component video cables (not included), connect the

COMPONENT VIDEO OUT terminal on the rear of the

DVD player to the COMPONENT IN terminal of TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of TV. Turn on the

DVD player and TV.

3

Press the input selector on your TV remote control until

the Component signal from the DVD player appears on the

TV screen.

4

Set the Video Output to P-SCAN in the Display Setup

menu. (See pages 29-30)

To see the progressive video output,

- Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive

Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s

menu system.

- Depending on your TV, the connection method may differ from the illustration above.

Note

- What is "Progressive Scan"?

Progressive scan has twice as many scanning lines as the interlace output method has. Progressive

scanning method can provide better and clearer picture quality.

RED

WHITE

RED

WHITE

RED

BLUE

GREEN

RED

BLUE

GREEN

Audio Cable

Component cable

connections

English _11

● CONNECTIONS

Connecting to a TV with DVI Jack

Connecting to a TV with HDMI Jack

HDMI VIDEO Specifications

- Depending on your TV, certain HDMI output resolutions may not work.

- Please refer to the user's manual of your TV.

- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds.

- If you set the HDMI output resolution 720p, 1080i or 1080p, HDMI output provides better picture quality.

- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player

using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).

(See page 32)

- If your TV has an logo, then it will Supports the Anynet+ Function.

1

Using the HDMI-DVI cable (not included), connect the

HDMI OUT terminal on the rear of the DVD player to the

DVI IN terminal of your TV.

2

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of your TV.

Turn on the DVD player and TV.

3

Press the input selector on your TV remote control until

the DVI signal from the DVD player appears on your TV

screen.

1

Using the HDMI-HDMI cable connect the HDMI OUT termi-

nal on the rear of the DVD player to the HDMI IN terminal

of your TV.

2

Press the input selector on your TV remote control until

the HDMI signal from the DVD player appears on your TV

screen.

RED

WHITE

RED

WHITE

Audio Cable

HDMI-DVI cable

HDMI cable

connections

12_ connections

Connection to an Audio System (2 Channel Amplifier)

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier.(See pages

28-29)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

• HDMI (High Definition Multimedia Interface)

HDMI is an interface to enable the digital transmission

of video and audio data with just a single connector.

Using HDMI, the DVD player transmits a digital video

and audio signal and displays a vivid picture on a TV

having an HDMI input jack.

• HDMI connection description

HDMI connector - Both uncompressed video data and

digital audio data (LPCM or Bit Stream data).

- Though the player uses a HDMI cable, the player

outputs only a pure digital signal to the TV.

- If TV does not support HDCP (High-bandwidth

Digital content protection), snow noise appears on

the screen.

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal.

However, when playing a DVD, the data transmitted

to a TV is digital. Therefore either a digital-to-analog

converter (in the DVD player) or an analog-to-digital

converter (in the TV) is required. During this conver-

sion, the picture quality is degraded due to noise and

signal loss. DVI technology is superior because it

requires no D/A conversion and is a pure digital sig-

nal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection)

is a system for protecting DVD content outputted

via DVI from being copied. It provides a secure

digital link between a video source (PC, DVD. etc)

and a display device (TV, projector . etc). Content is

encrypted at the source device to prevent unauthor-

ized

connections

English _13

● CONNECTIONS

Connection to an Audio System (2 Channel Amplifier)

1

Using the audio cables, connect the AUDIO (red and

white) OUT terminals on the rear of the DVD player to the

AUDIO (red and white) IN terminals of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO or

COMPONENT OUT terminals on the rear of the DVD play-

er to the VIDEO or COMPONENT IN terminal of your TV.

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier.(See pages

28-29)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

RED WHITE

RED

WHITE

2-Channel stereo amp

Audio Cable

• Why does Samsung use HDMI?

Analog TVs require an analog video/audio signal.

However, when playing a DVD, the data transmitted

to a TV is digital. Therefore either a digital-to-analog

converter (in the DVD player) or an analog-to-digital

converter (in the TV) is required. During this conver-

sion, the picture quality is degraded due to noise and

signal loss. DVI technology is superior because it

requires no D/A conversion and is a pure digital sig-

nal from the player to your TV.

• What is the HDCP?

HDCP (High-bandwidth Digital Content Protection)

is a system for protecting DVD content outputted

via DVI from being copied. It provides a secure

digital link between a video source (PC, DVD. etc)

and a display device (TV, projector . etc). Content is

encrypted at the source device to prevent unauthor-

ized

connections

14_ connections

basic functions

After plugging in the player, the first time you press the DVD

POWER button, this screen comes up: If you want to select

a language, Press the π/† buttons, and then press the

ENTER button. (This screen will only appear when you plug

in the player for the first time.)

If the language for the startup screen is not set, the set-

tings may change whenever you turn the power on or off.

Therefore, make sure that you select the language you want

to use.

Once you select a menu language, you can change it by

pressing the ( ) button on the front panel of the unit for

more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where

you can reset your preferred language.

1. Press the OPEN/CLOSE ( ) button. The STANDBY indi-

cator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label fac-

ing up.

3. Press the PLAY ( ) button or OPEN/ CLOSE

( ) button to close the disc tray.

When you stop disc

play, the player remembers where you stopped, so

when you press PLAY ( ) button again, it will pick up

where you left off.

Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)

1

If using a coaxial cable (not included), connect the

DIGITAL AUDIO OUT (COAXIAL) terminal on the rear

of the DVD player to the DIGITAL AUDIO IN (COAXIAL)

terminal of the Amplifier.

2

Using the video signal cable(s), connect the VIDEO,

COMPONENT or HDMI OUT terminals on the rear of the

DVD player to the VIDEO, COMPONENT or DVI IN termi-

nals of your TV as described on pages 9 to 12.

3

Turn on the DVD player, TV, and Amplifier.

4

Press the input select button of the Amplifier to select

external input in order to hear sound from the DVD player.

Refer to your Amplifier's user manual to set the Amplifier's

audio input.

Note

- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause

damage to the speakers and your ears.

- Please set the audio in the menu screen according to the Amplifier.(See pages 28-29)

- The position of terminals can vary depending on the Amplifier.

Please refer to the user's manual of the Amplifier.

Coaxial Cable

Dolby digital or

DTS amp

connections

English _15

● BASIC FUNCTIONS

basic functions

Playing a Disc

Before Play

- Turn on your TV and set it to the correct Video

Input by pressing TV/VIDEO button on the TV

remote control.

- If you connected an external Audio System, turn

on your Audio System and set it to the correct

Audio Input.

After plugging in the player, the first time you press the DVD

POWER button, this screen comes up: If you want to select

a language, Press the π/† buttons, and then press the

ENTER button. (This screen will only appear when you plug

in the player for the first time.)

If the language for the startup screen is not set, the set-

tings may change whenever you turn the power on or off.

Therefore, make sure that you select the language you want

to use.

Once you select a menu language, you can change it by

pressing the ( ) button on the front panel of the unit for

more than 5 seconds with no disc in the unit. Then the

SELECT MENU LANGUAGE window appears again where

you can reset your preferred language.

Playback

1. Press the OPEN/CLOSE ( ) button. The STANDBY indi-

cator light goes out and the tray opens.

2. Place a disc gently into the tray with the disc’s label fac-

ing up.

3. Press the PLAY ( ) button or OPEN/ CLOSE

( ) button to close the disc tray.

When you stop disc

play, the player remembers where you stopped, so

when you press PLAY ( ) button again, it will pick up

where you left off.

4. Stopping Play

Press the STOP ( ) button during play.

6. Pausing Play

Press the PAUSE ( ) button on the remote control during

play.

- Screen stops, no sound.

To resume, press the PLAY (

) button once again.

7. Slow Motion Play

Press the SEARCH (

/

) button to choose the

player speed between 1/2, 1/4, 1/8 and 1/16 of normal

during-PAUSE mode.

- No sound is heard during slow mode.

- Press the PLAY(

) button to resume normal play.

5. Removing Disc

Press the OPEN/CLOSE ( ) button.

Note

- If the player is left in the stop mode for more

than one minute without any user interaction, a

screen saver will be activated. Press the PLAY

( ) button to resume normal play.

- If the player is left in the stop mode for more than

about 30 minutes, the power will automatically

shut off.(Automatic Power-Off Function)

- If the player is left for about 5 minutes in pause

mode, it will stop.

- This ( ) icon indicates an invalid button press.

8. Step Motion Play (Except CD)

Press the PAUSE and then SKIP ( ) button on

the remote control during play.

- Each time the button is pressed, a new frame will

appear.

- No sound is heard during STEP mode.

- Press the PLAY (

) button to resume nor-

mal play.

- You can only perform step motion play in the forward

direction.

Select Menu Language

English

Français

Deutsch

Español

Italiano

Nederlands

basic functions

16_ basic functions

Using the Title Menu

1. During the playback of a DVD disc, press the DISC MENU

button on the remote control.

2. Press the π/† buttons for navigation/change selection,

then‑press ENTER button.

3. To make the screen disappear, press the RETURN or DISC

MENU button again.

1. During the playback of a DVD disc, press the ® /TITLE

MENU button on the remote control.

2. Press the π/† buttons to select for navigation/change

selection, then press the ENTER button.

3. To make the screen disappear, press the RETURN button

again.

Press the REPEAT button to change playback

mode.

When playing a DVD/VCD

‑ DVD repeats play by chapter or title

,

VCD repeat play

by disc or track

.

‑ Chapter : repeats the chapter that is playing.

‑ Title : repeats the title that is playing.

‑ Disc : repeats the disc that is playing.

‑ Off

Repeat Play

DVD

VCD

CD

2X, 4X, 64X, 128X

4X, 8X

2X, 4X, 8X

Skipping Tracks

During play, press the SKIP (

or ) button.

‑ When playing a DVD, if you press the SKIP ( ) button,

it moves to the next chapter. If you press the SKIP (

) button, it moves to the beginning of the chapter. One

more press makes it move to the beginning of the previous

chapter.

‑ When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1

or a CD, if you press the SKIP ( ) button, it moves to the

next track. If you press the SKIP ( ) button, it moves to

the beginning of the track. One more press makes it move

to the beginning of the previous track.

‑ If a track exceeds 15 minutes when playing a VCD and

you press the button, it moves forward 5minutes.

‑If you press the

button, it moves backward 5 minutes.

Note

When playing VCD, the Disc menu may not work.

Using the Display Function

When Playing a DVD/VCD/MPEG4

Using the Search and Skip

Functions

During play, you can search quickly through a chapter or

track, and use the skip function to jump to the next selection.

Searching through a Chapter or

Track

During play, press the SEARCH ( or ) button on the

remote control for more than 1 second.

Note

‑ The speed marked in this function may be

different from the actual playback speed.

‑ No sound is hearing during search mode

(Except CD).

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select the desired item.

‑ When playing VCD, the Disc menu may not work.

3. Press the √/® buttons to make the desired setup and then

press the ENTER button.

4. To make the screen disappear, press the INFO button

again.

Note

To access the desired title when there is more

than one in the disc.

For example, if there is more than one movie

on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so

that you can quickly find a specific passage

(similar to tracks on an video CD).

Allows playback of the lm from a desired

time. You must enter the starting time as a

reference.

The time search function does not operate

on some discs

Refers to the lm's soundtrack language.

In the example, the soundtrack is played in

English 5.1CH.A DVD disc can have up to

eight different soundtracks.

Refers to the subtitle languages available

in the disc. You will be able to choose the

subtitle languages or, if you prefer, turn them

off from the screen. A DVD disc can have up

to 32 different subtitles

E

Z

The EZ View funtion is use for changing the

aspect ratio in DVD.

This button has function as shortcut. Press

enter to activate the Zoom function.

To access the desired Angle function.

Some DVD disc are have more than one

recorded angle.

basic functions

English _17

● basic functions

Using the Disc Menu

Note

‑ Depending on a disc, the Disc Menu may not

work.

‑ You can also use the Disc Menu, using the

DISC MENU button on the remote control.

‑ When playing VCD, the Disc menu may not

work.

Using the Title Menu

Note

‑ Depending on a disc, the Title Menu may not

work.

‑ Title Menu will only be displayed if there are at

least two titles in the disc.

Using the Disc and Title

Menu

1. During the playback of a DVD disc, press the DISC MENU

button on the remote control.

2. Press the π/† buttons for navigation/change selection,

then‑press ENTER button.

3. To make the screen disappear, press the RETURN or DISC

MENU button again.

1. During the playback of a DVD disc, press the ® /TITLE

MENU button on the remote control.

2. Press the π/† buttons to select for navigation/change

selection, then press the ENTER button.

3. To make the screen disappear, press the RETURN button

again.

Press the REPEAT button to change playback

mode.

When playing a DVD/VCD

‑ DVD repeats play by chapter or title

,

VCD repeat play

by disc or track

.

‑ Chapter : repeats the chapter that is playing.

‑ Title : repeats the title that is playing.

‑ Disc : repeats the disc that is playing.

‑ Off

Repeat Play

Chapter

Title

Disc

Off

Using the A-B Repeat function

1. Press the REPEAT A‑B button on the remote control at

the point where you want repeat play to start (A).

2. Press the REPEAT A‑B button on the remote control at

the point where you want the repeat play to stop (AB).

DVD

A

AB

Off

Note

‑ A‑B REPEAT allows you to set point (AB) directly

after point (A) has been set.

‑ Depending on a disc, the Repeat function may

not work.

‑ When playing VCD, the Disc menu may not

work.

This feature allows you slowly to repeat scenes con‑

taining sports, dancing, musical instruments being

played etc., so you can study them more closely.

When playing a DVD

1. During play, press the PAUSE ( ) button.

2. Press the SEARCH (

/

) button to choose the play

speed between 1/2, 1/4, 1/8 and 1/16 of normal during

PAUSE mode.

Slow Play

Using the Display Function

When Playing a DVD/VCD/MPEG4

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select the desired item.

‑ When playing VCD, the Disc menu may not work.

3. Press the √/® buttons to make the desired setup and then

press the ENTER button.

Note

To access the desired title when there is more

than one in the disc.

For example, if there is more than one movie

on a DVD, each movie will be identified.

Most DVD discs are recorded in chapters so

that you can quickly find a specific passage

(similar to tracks on an video CD).

Allows playback of the lm from a desired

time. You must enter the starting time as a

reference.

The time search function does not operate

on some discs

Refers to the lm's soundtrack language.

In the example, the soundtrack is played in

English 5.1CH.A DVD disc can have up to

eight different soundtracks.

Refers to the subtitle languages available

in the disc. You will be able to choose the

subtitle languages or, if you prefer, turn them

off from the screen. A DVD disc can have up

to 32 different subtitles

E

Z

The EZ View funtion is use for changing the

aspect ratio in DVD.

This button has function as shortcut. Press

enter to activate the Zoom function.

To access the desired Angle function.

Some DVD disc are have more than one

recorded angle.

advanced functions

18_ advanced functions

Press

√/

AUDIO button

at remote control repeat-

edly to select the desired

Audio on MPEG4 then

press the ENTER .

1. Press the

π/

SUBTITLE button. The subtitle languages are

represented by abbreviations. The subtitle changes when

the button is pressed repeatedly.

Press

π/

SUBTITLE but-

ton at remocon repeat-

edly to select the desired

subtitle language on a

MPEG4 then press the

ENTER .

Adjusting the Aspect Ratio

(EZ View)

To play back using aspect ratio

(DVD)

If you are using a 16:9 TV

For 16:9 aspect ratio discs

- WIDE SCREEN

Displays the content of the DVD title in 16:9 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off.

When playing a 2.35:1 aspect ratio disc, the black bars at

the top and bottom of the screen will disappear. The picture

will look vertically stretched. (Depending on a type of disc,

the black bars may not disappear completely.)

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarge

For 4:3 aspect ratio discs

- Normal Wide

Displays the content of the DVD title in 16:9 aspect ratio.

The picture will look horizontally stretched.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears.

The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are

cut off and the central portion of the screen is enlarged.

- Vertical Fit

When a 4:3 DVD is viewed on a 16:9 TV, black bars will

appear at the left and right of the screen in order to prevent

the picture from looking horizontally stretched.

When playing a VCD you

can select among Stereo,

Right or Left.

VCD

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select

E

Z

icon. Press the √/®

buttons, the screen size change when these button is

pressed.

3. To make the screen disappear, press the INFO button again.

If you are using a 4:3 TV

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio.

The black bars will appear at the top and bottom of the

screen.

- 4:3 Pan Scan

The left and right portions of the screen are cut off and the

central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears. The picture will look vertically

stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut

off and the central portion of the screen is enlarged.

Note

This function may behave differently depending on

the type of disc.

Selecting the Audio

Language

You can select a desired audio language quickly and

easily with the

√/

AUDIO button.

Using the

√/

AUDIO button(DVD/

VCD/MPEG4)

1. Press the

√/

AUDIO button. The Audio changes when the

button is pressed repeatedly. The audio languages are rep-

resented by abbreviations.

DVD

***Dolby 5.1 CH

Stereo

advanced functions

English _19

● ADVANCED FUNCTIONS

Press

√/

AUDIO button

at remote control repeat-

edly to select the desired

Audio on MPEG4 then

press the ENTER .

MPEG4

1/1 MP3 2CH

Note

- This function depends on audio languages are

encoded on the disc and may not work.

-

A DVD disc can contain up to 8 audio languages.

- To have the same audio language come up

whenever you play a DVD;

Refer to “Using the Audio Language” on page 28.

- Possible warning messages that may appear if the

device (TV) that connected to the HDMI can't sup-

port RAW digital audio.

Selecting the Subtitle

Language

You can select a desired subtitle quickly and

easily with the π/SUBTITLE button.

Using the

π/

SUBTITLE button

(DVD/MPEG4)

1. Press the

π/

SUBTITLE button. The subtitle languages are

represented by abbreviations. The subtitle changes when

the button is pressed repeatedly.

DVD

Press

π/

SUBTITLE but-

ton at remocon repeat-

edly to select the desired

subtitle language on a

MPEG4 then press the

ENTER .

MPEG4

English

Subtitle 1/5

Note

- You have to change the desired subtitle in the

Disc Menu, according to discs. Press the DISC

MENU button.

- This function depends on what subtitles are

encoded on the disc and may not work on all DVDs.

- A DVD disc can contain up to 32 subtitle

languages.

- To have the same subtitle language come up

whenever you play a DVD; Refer to “Using the

Subtitle Language” on page 28.

Changing the Camera

Angle

When a DVD contains multiple angles of a particular

scene, you can use the ANGLE function.

Using the ANGLE function (DVD)

If the disc contains multiple angles, the ANGLE

appears on the screen.

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select icon.

3. To make the screen disappear, press the INFO button again.

4. Press the √/® buttons on the remote control to select the

desired angle.

Note

- If the disc has only one angle, this feature won’t

work. Currently, very few discs have this feature.

- Depending on the disc, these functions may not

work.

For 16:9 aspect ratio discs

- 4:3 Letter Box

Displays the content of the DVD title in 16:9 aspect ratio.

The black bars will appear at the top and bottom of the

screen.

- 4:3 Pan Scan

The left and right portions of the screen are cut off and the

central portion of the 16:9 screen is displayed.

- SCREEN FIT

The top and bottom portions of the screen are cut off and a

full screen appears. The picture will look vertically stretched.

- ZOOM FIT

The top, bottom, left and right of the screen are cut off and

the central portion of the screen is enlarged.

For 4:3 aspect ratio discs

- Normal Screen

Displays the content of the DVD title in 4:3 aspect ratio.

- SCREEN FIT

The top and bottom portions of the screen are cut off and

the full screen appears. The picture will look vertically

stretched.

- ZOOM FIT

The top, bottom, left and right portions of the screen are cut

off and the central portion of the screen is enlarged.

Selecting the Audio

Language

You can select a desired audio language quickly and

easily with the

√/

AUDIO button.

Using the

√/

AUDIO button(DVD/

VCD/MPEG4)

1. Press the

√/

AUDIO button. The Audio changes when the

button is pressed repeatedly. The audio languages are rep-

resented by abbreviations.

advanced functions

20_ advanced functions

Folder Selection

-

To select the Parent Folder

Press the RETURN button to go to parent folder, or press

the π/† buttons to select “..” and press ENTER to go to

the parent folder.

- : STOP icon

- : PLAY le icon

- : MP3 le icon

- : WMA le icon

- : JPEG le icon

- : AVI le icon

- : CD Audio le icon

- : Folder icon

- : Current Folder

icon

MP3/WMA/CD Audio Play-

back

1.

Open the disc tray. Place the disc on the tray.

Close the tray.

-

Only one kind of file is played back when a disc or a

folder contains both MP3 and WMA files.

2.

Press the π/† buttons to select a song file.

Press ENTER to begin playback of the song file.

Repeat/Random playback

Press the REPEAT button to change the playback mode. There

are four modes:

- Off, Track, Folder and Random.

- Off: Normal Playback

- Track: Repeats the current song file.

- Folder: Repeats the song files which have the same

extension in the current folder.

- Random: Song files which have the same extension will be

played in random order.

To resume normal play, press the CANCEL button.

Using the Bookmark

Function

This feature lets you bookmark sections of a DVD so

you can quickly find them at a later time.

Using the Bookmark Function

(DVD/VCD)

1. During play, press the Bookmark button on the remote con

trol.

2. When You reach the scene you want to mark, press the

ENTER button. Up to 12 scenes may be marked at a time.

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Note

- When VCD 2.0 is in Menu Off mode only, this

function works. Select Menu Off by pressing the

DISC MENU button.

- These functions may not Work on certain disc

types.

Recalling a Marked Scene

1. During play,press the Bookmark button on the remote

control.

2. Press the √/®/π/† buttons to select a marked

scene.

3. Press the PLAY ( ) button to skip to the

marked scene.

CANCEL

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Clearing a Bookmark

1. During play,press the Bookmark button on the remote

control.

2. Press the √/®/π/† buttons to select a marked

scene.

3. Press the CANCEL button to delete a bookmark

number.

CANCEL

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

Bookmark

Play

Clear

1

2

1

2

3

TT:01 CH:05 Time 0:39:23

Using the Zoom Function

Using the Zoom Function (DVD/

VCD)

1. During play, press the INFO button on the remote control.

2. Press the π/† buttons to select icon, then press the

ENTER button to zoom in 2x, 3x, 4x.

3. To make the screen disappear, press the INFO button again.

2x

Clips Menu for MP3/WMA/

JPEG/MPEG4/CD Audio

CD Audio or discs with MP3/WMA/JPEG/MPEG4

contain individual songs and/or pictures that will be

organized into folders on this unit as shown below.They

are similar to how you use your computer to put files

into different folders.

Open the disc tray.

Place the disc on the tray.

Close the tray.

The tray closes and this

screen displays.

- : Current Playback Mode : There are four

modes.

They can be selected in order by pressing the

REPEAT button.

- Off : Normal Playback.

- Track : Repeats the current track.

- Folder : Repeats the current folder.

- Random : Files in the disc will be played in

random order.

Off

Sayfa yükleniyor...

Samsung DVD-H1080 Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Samsung DVD-H1080 Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler