Yamaha EMX2 El kitabı

Marka: Yamaha

Model: EMX2

Kategori: Gitar aksesuarları

Tip: El kitabı

Page 1

POWERED MIXER

Introduction

Thank you and congratulations on your purchase of the Yamaha Powered Mixer EMX2.

Please read this manual thoroughly to get the most out of the product and ensure long-

term, trouble-free use. After reading this manual, keep it readily available for future

reference.

* Please read the “Precautions” on the back.

Main Features

• 500-watt power amplier for versatility in a wide variety of performance applications

• 10-channel mixer with four mono mic/line and three stereo line input channels, supporting

a wide range of inputs

• Yamaha’s high-quality SPX reverb, providing optimum processing for instruments or

vocals

• Feedback Suppressor, which automatically cuts and prevents undesirable feedback noise

• Independent three-band equalizer on each channel for tonal adjustment and sound

control

Accessories (Please check that they are included with

your powered mixer.)

• AC power cord (2 m)

• Technical Specications (English only): Includes general specications, input/output

characteristics, a block diagram, dimensions, and a jack and plug list.

• Owner’s Manual (this leaet)

Quick Start Guide

Setup

1 Make sure that all switches, including the mixer’s power switch

[

are not on

(N).

Use the mixer with the operating panel facing up.

Connecting speakers, microphones, instruments,

and audio devices

2 Refer to the connection example in the illustration below.

Connection Example

Set to “8Ω” if speakers

are connected as

shown in the gure

above.

Micro-

phones

Micro-

phones

Electric

acoustic

guitar

Electric

guitar

Keyboard

Audio

device

Portable

audio

player

Footswitch

(Yamaha FC5)

See “Precautions for

Connecting the

Speakers” below.

Passive speakers

(Impedance: 8 Ω)

 Precautions for Connecting the Speakers

6 Ω

Set to “4Ω.”

Parallel connection

8 Ω 8 Ω

Set to “4Ω.”

• You must set the [IMPEDANCE SELECT] switch correctly

according to the connection method and number of

speakers. Be sure that the impedance of your speakers is

no less than the impedance that you set on the mixer.

Setting this switch incorrectly could result in damage to

the mixer/your speakers.

Actual speaker impedance* [IMPEDANCE SELECT] switch

4 Ω to less than 8 Ω Set to “4Ω.”

8 Ω and over Set to “8Ω.”

If you are unsure of the

impedance of the connected

speakers

Set to “4Ω.”

* For parallel connections: synthetic impedance

• Make sure to insert the speaker cables all the way inside

until secure. Failure to do so may result in damage to your

equipment.

• Use speaker cables with an insulated-housing connector.

Getting sound to the speakers

3 Connect the included power cord.

First, connect it to the mixer’s [AC IN] jack, then to

a power outlet.

NOTE Reverse the order when removing the power cord.

Equalizer

4 Turn the mixer’s

[LEVEL] controls (white

knobs) and [MASTER

LEVEL] control (red

knob) to the minimum

(zero). Also, set the

equalizer controls

(green knobs) to the

center “D” or “MUSIC”

position.

5 Set the [N MIC/O LINE] switch

to the “

N MIC” position for

microphone connection, and to

the “

O LINE” position for

connection of an instrument or

audio device.

NOTE If you are using condenser microphones,

turn on the [PHANTOM (CH1/2)] switch.

6 Turn on the power of the

connected sound source (if

applicable), then the mixer.

The [POWER] LED lights.

WARNING

To avoid any loud, unexpected noise from the

speaker, first turn off the power to the mixer, then

the connected sound source (such as an

instrument or audio device).

7 For channels to which a microphone, instrument, or audio device

is connected, set [LEVEL] to the “D” position.

8 While outputting sound from the microphone, instrument, or

audio device, slowly turn the [MASTER LEVEL] to the right until

you reach the optimal volume.

9 Adjust [LEVEL] on each channel as necessary to set the volume

balance between the microphone, instrument, and audio device.

AC IN

Controls and Functions

Applying Reverb

The EMX2 features a built-in reverb processor that is in the same league as our famed

SPX effect processor series. This reverb lets you simulate the acoustics of different

performance environments, such as concert halls and small clubs, and add warm,

natural ambience to your vocals or instrument performance.

1 Press the [REVERB] button to turn it on.

The LED lights when REVERB is on.

2 Turn the REVERB [TYPE/TIME] control to the

desired reverb type and time (length).

Turning the control to the right lengthens the time of the

selected reverb type.

Short

Long

Making optimum volume settings

When the volume is too loud

Turn the [LEVEL] control to the minimum (zero). Set the

[

N MIC/O LINE] switch to the “O LINE” position, then slowly

raise the [LEVEL] control until the desired volume is reached.

When the volume is too soft

Turn the [LEVEL] control to the minimum (zero). Set the

[

N MIC/O LINE] switch to the “ N MIC” position, then slowly

raise the [LEVEL] control until the desired volume is reached.

3 Use the [REVERB] control to adjust the reverb amount of the

corresponding channel.

If necessary, repeat steps 2 and 3 to determine the optimum reverb setting.

1 Mic/Line input jacks (channels 1– 4)

Connect microphones, guitars, electronic musical instruments

or audio devices. Channels 3 and 4 provide combo jacks that

support both XLR and phone plugs.

XLR Phone

2 [N MIC/O LINE] switches (channels 1– 4)

For low-level signals (including microphones), set the switch to

the “

N MIC” position. For high-level signals (including

electronic instruments and audio devices), set the switch to the

“

O LINE” position.

3 [Hi-Z] switch (channel 4)

This switch is used when connecting a device directly to the

mixer without a DI (direct injection box) — for example,

instruments with passive pickups, such as an acoustic-electric

guitar or electric bass without battery. This function is effective

only for the phone jack input.

4 [LINE] input jacks (channels 5/6, 7/8, 9/10)

Connect line-level devices such as electronic instruments,

acoustic-electric guitars, CD players, and portable audio

players. These jacks support phone, RCA-pin, and stereo-mini

plugs.

RCA-pin Stereo-mini

NOTE For the channel 7/8 input, if both phone and RCA-pin jacks are

used at the same time, the phone jack will take priority. For the

channel 9/10 input, if both phone and stereo-mini jacks are

used at the same time, the stereo-mini jack will take priority.

The signal from the device connected to another jack will be

muted.

5 [MONITOR OUT] jacks

These are for connection to a powered speaker for monitoring

purposes, and output a mix of the signals from channels 1 to

9/10. You can adjust the output level using the [MONITOR OUT]

control !. If only the [L (MONO)] jack is used, the signals from

the L and R channels are mixed and output.

6|[SUBWOOFER OUT] jack

This is for connection to a powered subwoofer, and outputs a

mono signal. If this jack is in use, the low frequencies below

120 Hz to the [SPEAKERS L/R] jacks will be cut. The output

level is linked to that of the [MASTER LEVEL] control (C).

7 [REVERB FOOT SW] jack

This is for connection to an unlatched-type footswitch such as

the Yamaha FC5 — useful for solo performers, since you can

toggle the reverb on and off as needed with your foot.

8 [SPEAKERS L/R] jacks

Use commercially available speaker cables to connect the

speakers. These jacks support TS phone plugs.

9 [IMPEDANCE SELECT] switch

Set this switch to match the impedance of the connected

speakers. If you are unsure of the impedance of the connected

speakers, set this switch to “4Ω”. Changing this setting changes

the maximum output from the amp and changes the conditions

for which the [LIMITER] LED comes on.

NOTICE

• Make sure the power switch is off before changing the setting of this

switch.

• Setting this switch incorrectly could result in damage to the mixer/your

speakers.

) [PHANTOM (CH1/2)] switch/LED

When this switch is on, the LED lights indicating that phantom

power is available for channels 1 and 2. Turn this switch on to

supply power to condenser microphones or a DI (direct

injection box).

NOTICE

Follow the important precautions below, in order to prevent noise and

possible damage to external devices and the mixer when you operate

this switch.

• Be sure to leave this switch off if you do not need phantom power, or

when you connect a device that does not support phantom power to

channels 1 and 2.

• Do not connect/disconnect a cable to/from channel 1 or 2 while this

switch is on.

• Turn the [LEVEL] control of channels 1 and 2 to the minimum before

operating this switch.

! [MONITOR OUT] control

Determines the signal level output from the [MONITOR OUT]

jacks (5). The [MASTER LEVEL] control does not affect the

[MONITOR OUT] signal.

@ Equalizer controls [HIGH, MID, LOW]

The equalizer shapes the [HIGH], [MID], and [LOW] audio

frequencies. Turning the control to the right amplies (boosts)

the corresponding frequency band, while turning it to the left

attenuates (cuts) the band. Setting the control to the “D”

position produces a at response in the corresponding band.

# [REVERB] button/LED

When this button is on, the LED lights indicating that you can

apply reverb. This button is off when you turn on the mixer.

(Unlike other switches, this button cannot be locked.)

$ REVERB [TYPE/TIME] control

Determines the reverb type and its length. Turning the control to

the right lengthens the time of the selected reverb type.

“HALL”: Simulated reverb of a large space, such as a

concert hall.

“PLATE”: Simulated metal plate reverb, producing a more

hard-edged and bright sound.

“ROOM”: Simulated acoustic ambience of a small room.

“ECHO”: Echo effect suitable for vocals.

% [REVERB] controls (channels 1– 4)

Determines the amount of reverb for each channel when the

[REVERB] button (#) is on.

^ [N STEREO /O MONO] switches

(channels 5/6, 7/8, 9/10)

Setting the switch to “

STEREO” will assign the signals from

the L and R channels to each left and right speaker and output

each signal. Setting the switch to “

MONO” will mix the output

of different L and R sources to output the same signal to both

the left and right speakers. For keyboards with mono output,

guitars, or other non-stereo sound sources, when the switch is

set to “

MONO”, the stereo jacks can be conveniently used as

multiple mono jacks.

& Level meter

The level meter shows the level of output signal from the

[SPEAKERS L/R] jacks.

NOTICE

If used at a high volume so that the [LIMITER] LED flashes continuously,

the internal power amplifier section is being excessively overloaded and

may malfunction. Reduce the output level with the [MASTER LEVEL]

control so that the indicator flashes only briefly on the highest transient

peaks.

* [POWER] LED

This LED lights when the power is turned on by pressing the

power switch.

( [FEEDBACK SUPPRESSOR] switch/LED

When this switch is on, the LED lights indicating that feedback

is automatically suppressed. (This utilizes a seven-band notch

lter. When this switch or the power switch is off, the notch lter

will be reset.)

A [LEVEL] controls

Use these controls to adjust the volume for each channel. To

reduce noise, set any [LEVEL] controls on unused channels to

the minimum.

B [MASTER EQ] control

Use this control to adjust the overall sound frequency balance.

The center position “MUSIC” is a basic setting and if you turn

the control to the left, this creates an optimum setting for

speech, cutting unneeded low range frequencies. Turning the

control to the right creates an optimum setting for playback of

sound sources, by boosting the low and high ranges. If you turn

the control further to the right, the [BASS BOOST] LED lights

indicating that the bass boost function is active, giving you an

even more powerful bass tone.

C [MASTER LEVEL] control

Determines the volume of the signal output from the

[SPEAKERS L/R] and [SUBWOOFER OUT] jacks. This allows

you to adjust the overall volume without changing the relative

volume balance among the various channels.

D Vents

There are vents located on both sides of the mixer, and a

cooling fan is installed on the exhaust side. Do not block the

vents on either side when using the mixer.

E [AC IN] jack

Connect the included power cord here.

F [ ] (Power) switch

For turning the power of the mixer on (O) and off (N).

NOTICE

Rapidly turning the mixer on and off in succession can cause it to

malfunction. After turning the mixer off, wait for about 10 seconds before

turning it on again.

Owner’s Manual

ZR97470

AC IN

Page 2

Mounting to a Microphone Stand

The mixer can be mounted onto a microphone

stand as illustrated at right, by using the

optionally available Yamaha BMS-10A Mic

Stand Adaptor. For instructions on mounting,

refer to the BMS-10A Owner’s Manual.

Yamaha Pro Audio global website:

http://www.yamahaproaudio.com/

Yamaha Downloads:

http://download.yamaha.com/

Manual Development Group

Published 04/2016 MWHD-B0

Printed in China

Rack Mounting

1 Use a screwdriver to loosen and remove the screws (4) on the

handles installed on the mixer.

2 Use the screws you removed in Step 1 to securely install the RK-

EMX2 Rack-Mount Kit (sold separately) on the mixer.

Orient the RK-EMX2 rack-mount brackets with the engraved lettering facing toward

the rear.

NOTICE

Be sure to use the screws removed in Step 1. Using other screws can cause damage.

NOTE Separate screws for mounting the mixer in a rack are not included with the mixer.

General Specications

Maximum Output Power

(1 kHz)

THD+N<10% 250 W + 250 W (4 Ω), 170 W + 170 W (8 Ω)

THD+N<1% 110 W + 110 W (4 Ω), 110 W + 110 W (8 Ω)

Input Channels

10 channels (Mono (MIC/LINE): 4, Stereo (LINE): 3)

CH4: Hi-Z input supported

Output Channels

SPEAKERS (L, R): 1, MONITOR OUT(L, R): 1, SUBWOOFER OUT: 1

Bus

Stereo: 1, Effect: 1

Input Channel Equalization

HIGH: 8 kHz ±15 dB

MID: 2.5 kHz ±15 dB

LOW: 100 Hz ±15 dB

Level Meter

6 points (-20, -6, 0, +3, +6, LIMITER)

Phantom Power Voltage

+30 V (CH1, 2)

Built-in

Effect

SPX

Algorithm

4 programs

REVERB FOOT SW

Effect Mute on/off

DSP Processing

FEEDBACK SUPPRESSOR, MASTER EQ

Protection

Load Protection: DC-fault

Amplier Protection: Over heat protection, Over current protection

Power Supply Protection: Over heat protection, Over current protection

Power Requirements

AC 100-240 V, 50 Hz/60 Hz

Power Consumption

35 W (Idle) / 90 W (1/8 Power)

Dimensions (W × H × D)

375 mm × 147 mm × 220 mm (14.8" × 5.8" × 8.7")

Net Weight

4.2 kg (9.3 lbs)

Optional Accessory

Foot Switch: FC5, Rack-Mount Kit: RK-EMX2, Mic Stand Adaptor: BMS-10A

Operating Temperature

0 to +40˚C

For other specications, see the included “Technical Specications.”

The contents of this manual apply to the latest specications as of the publishing date. To obtain the latest manual, access the Yamaha

website then download the manual le.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE

PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, re

or other hazards. These precautions include, but are

not limited to, the following:

Power supply/power cord

•Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over,

or roll anything over it.

•Only use the voltage speciﬁed as correct for the device.

The required voltage is printed on the name plate of the

device.

•Use only the supplied power cord/plug.

If you intend to use the device in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

•Check the electric plug and each jack periodically, and

remove any dirt or dust which may have accumulated. Failure

to do so may cause electrical shock, short-circuiting or ﬁre.

•When setting up the device, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is not

unplugged from the wall AC outlet, the device will not be

disconnected from the power source.

•Remove the electric plug from the outlet when the device is

not to be used for extended periods of time, or during

electrical storms.

•Be sure to connect to an appropriate outlet with a

protective grounding connection.

Do not open

•This device contains no user-serviceable parts. Do not

open the device or attempt to disassemble the internal

parts or modify them in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualiﬁed Yamaha service personnel.

Water warning

•Do not expose the device to rain, use it near water or in

damp or wet conditions, or place on it any containers

(such as vases, bottles or glasses) containing liquids

which might spill into any openings. If any liquid such as

water seeps into the device, turn off the power immediately

and unplug the power cord from the AC outlet. Then have

the device inspected by qualiﬁed Yamaha service

personnel.

•Never insert or remove an electric plug with wet hands.

Hearing loss

•Avoid setting all equalizer and level controls to their

maximum. Depending on the condition of the connected

devices, doing so may result in feedback that can cause

hearing loss and damage the speakers.

•Do not use speakers for a long period of time at a high or

uncomfortable volume level, since this can cause

permanent hearing loss. If you experience any hearing loss

or ringing in the ears, consult a physician.

•When turning on the AC power in your audio system,

always turn on the device LAST, to avoid hearing loss and

speaker damage. When turning the power off, the device

should be turned off FIRST for the same reason.

Fire warning

•Do not place any burning items or open ﬂames near the

device, since they may cause a ﬁre.

If you notice any abnormality

•If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet.

- The power cord or plug becomes frayed or damaged.

- Unusual smells or smoke are emitted.

- Some object has been dropped into the device.

- There is a sudden loss of sound during use of the device.

- Cracks or other visible damage appear on the device.

Then have the device inspected or repaired by qualiﬁed

Yamaha service personnel.

•If this device should be dropped or damaged, immediately

turn off the power switch, disconnect the electric plug from

the outlet, and have the device inspected by qualiﬁed

Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or others,

or damage to the device or other property. These precau-

tions include, but are not limited to, the following:

Power supply/power cord

•When removing the electric plug from the device or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

Location

•Do not place the device in an unstable position where it

might accidentally fall over and cause injuries. Use the

device with the operating panel facing up.

•Do not block the vents. This device has ventilation holes at

the sides to prevent the internal temperature from

becoming too high. In particular, do not place the device

on its side or upside down. Inadequate ventilation can

result in overheating, possibly causing damage to the

device(s), or even ﬁre.

•When using the device:

- Do not cover it with any cloth.

- Do not install it on a carpet or rug.

- Do not use the device in a conﬁned, poorly-ventilated

location.

Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), or even ﬁre. If this device

is to be used in a small space other than an EIA-standard

rack, make sure that there is adequate space around the

device: at least 30cm above, 30cm at the sides and 30cm

behind.

•Do not place the device in a location where it may come

into contact with corrosive gases or salt air. Doing so may

result in malfunction.

•Before moving the device, remove all connected cables.

•If the device is mounted in an EIA standard rack, carefully

read the section “Precautions for Rack Mounting” on page

2. Inadequate ventilation can result in overheating, possibly

causing damage to the device(s), malfunction, or even ﬁre.

Connections

•Do not use speaker cables with a metal-housing connector.

Doing so may result in electrical shock due to differences

in voltage. Use speaker cables with a nonmetal-housing

connector, or with a insulated-housing connector.

•Before connecting the device to other devices, turn off the

power for all devices. Also, before turning the power of all

devices on or off, make sure that all volume levels are set

to the minimum. Failing to do so may result in electric

shock or equipment damage.

•Use only speaker cables for connecting speakers to the

speaker jacks. Use of other types of cables may result in

ﬁre.

Maintenance

•Remove the power plug from the AC outlet when cleaning

the device.

Handling caution

•Avoid inserting or dropping foreign objects (paper, plastic,

metal, etc.) into any gaps or openings on the device (vents,

panel, etc.) If this happens, immediately turn off the power,

unplug the power cord from the AC outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

•Do not rest your weight on the device or place heavy

objects on it. Avoid applying excessive force to the buttons,

switches or connectors to prevent injuries.

Yamaha cannot be held responsible for damage caused

by improper use or modiﬁcations to the device.

(PA_en_7)

European Models

Purchaser/User Information speciﬁed in EN55103-2:2009.

Conforms to Environments: E1, E2, E3 and E4

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is

at the bottom of the unit. You should note this serial number in the space provided below and retain this manual

as a permanent record of your purchase to aid identication in the event of theft.

Model No.

Serial No.

(bottom_en_01)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC

requirements. Modications not expressly approved by Yamaha may void your authority, granted by the

FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.

Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC

Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a

reasonable level of assurance that your use of this product in a residential environment will not result in

harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if

not installed and used according to the instructions found in the users manual, may cause interference

harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee

that interference will not occur in all installations. If this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using

one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line lter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm

ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized

to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha

Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its

subsidiaries.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

In Finland: Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.

In Norway: Apparatet må tilkoples jordet stikkontakt.

In Sweden: Apparaten skall anslutas till jordat uttag.

(class I hokuo)

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property, follow

the notices below.

 Handling and maintenance

•Do not use the device in the vicinity of a TV, radio, AV

equipment, mobile phone, or other electric devices.

Otherwise, the device, TV, or radio may generate noise.

•Do not expose the device to excessive dust or vibration, or

extreme cold or heat (such as in direct sunlight, near a

heater, or in a car during the day), in order to prevent the

possibility of panel disﬁguration, unstable operation, or

damage to the internal components.

•Do not place vinyl, plastic or rubber objects on the device,

since this might discolor the panel.

•When cleaning the device, use a dry and soft cloth. Do not

use paint thinners, solvents, cleaning ﬂuids, or chemical-

impregnated wiping cloths.

•Condensation can occur in the device due to rapid, drastic

changes in ambient temperature—when the device is

moved from one location to another, or air conditioning is

turned on or off, for example. Using the device while

condensation is present can cause damage. If there is

reason to believe that condensation might have occurred,

leave the device for several hours without turning on the

power until the condensation has completely dried out.

•Always turn the power off when the device is not in use.

 Connectors

•XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Information

 About this manual

•The illustrations as shown in this manual are for

instructional purposes only.

•The company names and product names in this manual

are the trademarks or registered trademarks of their

respective companies.

Information for users on collection and

disposal of old equipment:

This symbol on the products, packaging,

and/or accompanying documents means that

used electrical and electronic products

should not be mixed with general household

waste.

For proper treatment, recovery and recycling

of old products, please take them to applicable collection

points, in accordance with your national legislation.

By disposing of these products correctly, you will help to

save valuable resources and prevent any potential

negative effects on human health and the environment

which could otherwise arise from inappropriate waste

handling.

For more information about collection and recycling of old

products, please contact your local municipality, your

waste disposal service or the point of sale where you

purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment,

please contact your dealer or supplier for further

information.

Information on Disposal in other Countries outside the

European Union:

This symbol is only valid in the European Union. If you

wish to discard these items, please contact your local

authorities or dealer and ask for the correct method of

disposal.

(weee_eu_en_02)

IMPORTANT NOTICE FOR THE UNITED

KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in

accordance with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug proceed

as follows:

The wire which is coloured GREEN-and-YELLOW must

be connected to the terminal in the plug which is marked

by the letter E or by the safety earth symbol

colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to

the terminal which is marked with the letter N or

coloured BLACK.

The wire which is coloured BROWN must be connected

to the terminal which is marked with the letter L or

coloured RED.

(3 wires)

 Precautions for Rack Mounting

This mixer is rated for operation at ambient temperatures ranging from 0 to 40 degrees

Celsius. If you install this mixer along with other devices in a poorly ventilated EIA

standards rack, the ambient temperature inside the rack may rise, resulting in

inefficient performance. Be sure to rack-mount in the following conditions so the mixer

does not overheat.

• When mounting the mixer in a rack with devices such as power ampliers that generate a

signicant amount of heat, leave more than 1U of space between it and other equipment. Also,

either leave the open spaces uncovered or install appropriate ventilating panels to minimize the

possibility of heat buildup.

• To ensure sufficient airow, leave the rear of the rack open. If you’ve installed a fan kit in the rack,

there may be cases in which closing the rear of the rack will produce a greater cooling effect.

Refer to the rack and/or fan kit manual for details.

Troubleshooting

Check the following items before contacting a Yamaha dealer.

If the symptoms are not improved, contact your nearest Yamaha dealer.

Power does not come on.

 Did you rmly and securely connect

the power cord?

Power shuts down suddenly.

 Are the vents of the mixer blocked?

Since inadequate ventilation can result in

overheating the mixer, the power may be

turned off automatically to prevent

overheating. Ensure proper ventilation for

cooling, and then turn on the power again.

No sound is heard.

 Did you connect the mixer’s

[SPEAKERS L/R] jacks and the

speakers’ input jacks using the proper

speaker cables?

 Did you rmly and securely connect

the speaker cables?

 Is the [POWER] LED ashing at

intervals?

There may be a short in the speaker cable or

the connection may be faulty. Check that the

speaker cable is not scratched and is

connected properly to the mixer, and then

turn the power on again.

 For channels 7/8, are both phone and

RCA-pin jacks connected at the same

time? Or, for channels 9/10, are both

phone and stereo-mini jacks connected

at the same time?

The phone jack has priority for channels 7/8

and the stereo-mini jack has priority for

channels 9/10.

 Is the [POWER] LED ashing

continuously?

If the internal power amplier section is

excessively overloaded, the amplier will be

muted for protection. The mixer will

automatically reset itself after a while.

Sound is distorted or noise is

produced.

 Are the [LEVEL] controls of all relevant

channels and/or the [MASTER LEVEL]

control set too high?

 Is the [

N MIC/O LINE] switch of the

corresponding channel set to

“

N MIC”?

If the input level from the source is high,

setting the [

N MIC/O LINE] switch to

“

N MIC” may result in distorted sound. Set

the switch to the “

O LINE” position.

 Is the volume of the device connected

to the mixer too high?

Lower the volume of the external device.

 Is the speaker cable or power cord

located near the input cables?

Please keep speaker cables and the power

cord away from the input cables.

Sound is not loud enough.

 Are the [LEVEL] controls of all relevant

channels and/or the [MASTER LEVEL]

control set too low?

 Is the [

N MIC/O LINE] switch of the

corresponding channel set to

“

O LINE”?

Turn the [LEVEL] control to the minimum

(zero). Next, set the switch to the “

N MIC”

position, and then slowly raise the [LEVEL]

control.

 Is the volume of the device connected

to the mixer too low?

Raise the volume of the external device.

 Is the [PHANTOM (CH1/2)] switch set to

on when using a microphone that

requires phantom power?

The high sounds and low

sounds are unbalanced.

 Are the equalizer controls raised or

lowered too much?

Set the equalizer controls to the center

position.

Orient the rack-

mount bracket

with the engraved

lettering facing

toward the rear.

Orient the rack-

mount bracket

with the engraved

lettering facing

toward the rear.

The mixer can be rack mounted

without the handles installed.

NOTE The EMX2 requires at least 6 U of

rack space. To take into account the

cable connections, we recommend

to ensure 7 U of rack space.

Yamaha EMX2 El kitabı

Marka: Yamaha

Model: EMX2

Kategori: Gitar aksesuarları

Tip: El kitabı

PDF İndir

rapor

Diğer dillerde

español: Yamaha EMX2 El manual del propietario
français: Yamaha EMX2 Le manuel du propriétaire
italiano: Yamaha EMX2 Manuale del proprietario
svenska: Yamaha EMX2 Bruksanvisning
čeština: Yamaha EMX2 Návod k obsluze
polski: Yamaha EMX2 Instrukcja obsługi
Deutsch: Yamaha EMX2 Bedienungsanleitung
português: Yamaha EMX2 Manual do proprietário
English: Yamaha EMX2 Owner's manual
dansk: Yamaha EMX2 Brugervejledning
русский: Yamaha EMX2 Инструкция по применению
suomi: Yamaha EMX2 Omistajan opas
Nederlands: Yamaha EMX2 de handleiding
română: Yamaha EMX2 Manualul proprietarului

Yamaha EMX2 El kitabı

Yamaha EMX2 El kitabı

Diğer dillerde

İlgili Makaleler