Yamaha MCR-940 El kitabı

OWNER'S MANUAL

MODE D'EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

GF

RECEIVER/BLU-RAY DISC PLAYER

AMPLI-TUNER/LECTEUR BLU-RAY DISC

MCR

-

940

(R-840

+

BD-940

+

NS-BP300)

i

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou de

méthodes autres que ceux décrits ci-dessous, peuvent

entraîner une exposition à un rayonnement dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die Einstellung

bzw. die Ausführung von anderen als in dieser Anleitung

beschriebenen Vorgängen kann zu Gefährdung durch

gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande av

åtgärder på annat sätt än så som beskrivs häri kan resultera i

farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure non

specificati in questo manuale possono risultare in esposizione

a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos que

no se especifican enste manual pueden causar una exposición

peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of procedures

anders dan beschreven in dit document kan leiden tot

blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или произведение

настроек или выполнение процедур, не указанных в

данной инструкции, может отразиться на выделении

опасной радиации.

BD-940

ᵈᗧߎߎࠍ㐿ߊߣࠢ࡜ࠬ㧞ߩนⷞ෸߮ਇนⷞ࡟࡯ࠩ᡼኿߇಴߹ߔޕ

࡟࡯ࠩ᡼኿ࠍߩߙ߈ㄟ߹ߥ޿ߢߊߛߐ޿ޕ

CAUTION: CLASS 2 VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN. DO NOT STARE INTO THE BEAM.

VARNING: KLASS 2 SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. TITTA INTE IN I STRÅLEN.

HUOMIO: AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE

LUOKAN 2 LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

ADVARSEL: KLASSE 2 SYNLIG OG USYNLIG LASERSTRÅLING HVIS DENNE

DELEN ÅPNES. STIRR IKKE INN I STRÅLEN.

ADVARSEL: KLASSE 2 SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.

KIG IKKE IND I STRÅLEN.

ACHTUNG: BEI GEÖFFNETER ABDECKUNG IST SICHTBARE UND

UNSICHTBARE LASERSTRAHLUNG DER KLASSE 2 IM

GERÄTEINNEREN VORHANDEN. NICHT IN DEN STRAHL SEHEN.

ATTENTION: RADIATIONS LASER VISIBLES ET INVISIBLES

DE CLASSE 2 OUAND OUVERT. NE PAS REGARDER

FIXEMENT LE FAISCEAU.

SA172WJ

BD-940

ii

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten

muutto saattaa altistaa vaaralliselle säteilylle tai muille

vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for

stråling.

Bemærk: Netafbryderen er sekundært indkoblet og ofbryder

ikke strømmen fra nettet. Den indbyggede netdel er derfor

tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

N

Observer: Nettbryteren er sekundert innkoplet. Den

innebygdenetdelen er derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för osynlig

laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Strömbrytaren är sekundärt kopplad och inte bryter

inte strömmen från nätet. Den inbyggda nätdelen är därför

ansluten till elnätet så länge stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1

ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja

roiskevedelle.

Huom. Toiminnanvalitsin on kytketty toisiopuolelle, eikä se

kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on

kytkettynä sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA

EJ STRÅLEN.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean

place and away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the following

minimum clearances.

Top: 30 cm (R-840 Only)

Rear: 10 cm

Sides: 10 cm

3 Locate this unit away from other electrical appliances, motors, or

transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold

to hot, and do not locate this unit in an environment with high

humidity (i.e. a room with a humidifier) to prevent condensation

inside this unit, which may cause an electrical shock, fire,

damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this

unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this

unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.

in order not to obstruct heat radiation. If the temperature inside

this unit rises, it may cause fire, damage to this unit, and/or

personal injury.

7 Do not plug in this unit to a wall outlet until all connections are

complete.

8 Do not operate this unit upside-down. It may overheat, possibly

causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp

the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage

the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit

with a higher voltage than specified is dangerous and may cause

fire, damage to this unit, and/or personal injury. Yamaha will not

be held responsible for any damage resulting from use of this unit

with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and

outdoor antennas disconnected from a wall outlet or this unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e.

vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press to set it to standby mode and

disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the outlet,

then leave this unit alone.

19 When using this unit for a long time, this unit may become warm.

Turn the power off, then leave this unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug

can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

22 Excessive sound pressure from earphones and headphones can

cause hearing loss.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc tray

and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off by . This state is called standby mode. In this

state, this unit is designed to consume a very small quantity of

power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

LASER Specification:

Class 1 LASER Product

Wave length: 788 nm (CDs)/654 nm (DVDs)/405 nm

(BDs)

Laser power: No hazardous radiation is emitted with

the safety protection

1 En

English

PREPARATIONINTRODUCTION

TUNER

OPERATIONS

OTHER

OPERATIONS

ADDITIONAL

INFORMATION

BASIC

OPERATIONS

FEATURES ............................................................. 2

SUPPLIED ACCESSORIES ................................. 2

ABOUT DISCS ....................................................... 3

Types of Discs that Can Be Used with This Player ... 3

Discs that Cannot Be Used with This Player............. 3

CONTROLS AND FUNCTIONS.......................... 4

Receiver (R-840)........................................................ 4

BD player (BD-940) .................................................. 5

Remote control........................................................... 6

PREPARATIONS ................................................... 8

Connecting speakers/external components/

antennas ................................................................. 8

Connecting a recorder (CDR, MDR, etc.),

AV receiver or decoder (CDR, MDR, etc.) ........... 9

Connecting power cables........................................... 9

Connecting an iPod™.............................................. 10

Connecting to the Internet ....................................... 10

Installing the batteries in the remote control ........... 11

Using the remote control ......................................... 11

Adjusting the Clock ................................................. 12

SETTING THE SYSTEM ................................... 13

Turn on the TV and the system................................ 13

Setting the TV display ............................................. 13

On-screen display (OSD) language ......................... 13

Audio, Subtitle and Disc menu languages............... 14

SYSTEM OPERATIONS..................................... 15

Basic system operations........................................... 15

Changing the brightness of the front panel

display ................................................................. 16

To use headphones................................................... 16

DISC OPERATIONS............................................ 17

Using the on-screen display..................................... 17

Playback operations................................................. 17

Pausing playback ..................................................... 17

Rewind and fast forward.......................................... 18

Selecting chapters and tracks................................... 18

BD/DVD menus....................................................... 18

Slow-motion playback ............................................. 18

Frame-by-frame playback........................................ 18

Selecting languages and audio................................. 19

Selecting subtitles .................................................... 19

Selecting camera angles........................................... 19

Repeat playback....................................................... 19

Repeat playback of a specified part (A-B repeat).... 20

Playing JPEG slideshows......................................... 20

Playing back still images in a selected folder.......... 21

Playing back movies recorded on a DVD-R/

DVD-RW............................................................. 21

Using “Function Control Screen” for BD/DVD...... 22

Using “Functions” menu for Audio CD .................. 23

Viewing disc information......................................... 23

Enjoying BONUSVIEW and BD-LIVE.................. 24

FM TUNING..........................................................26

Automatic tuning ..................................................... 26

Manual tuning.......................................................... 26

Automatic preset tuning........................................... 26

Manual preset tuning ............................................... 27

Selecting preset stations........................................... 27

RADIO DATA SYSTEM TUNING

(EUROPE MODEL ONLY) .............................28

Displaying the Radio Data System information ...... 28

Using the TP (traffic program) data service ............ 29

CT (clock time) settings .......................................... 29

SETTING THE TIMER .......................................30

Setting the clock timer............................................. 30

Setting the sleep timer ............................................. 31

CONTROLLING iPod™......................................32

Using iPod™ ........................................................... 32

SETTINGS OF THE BD PLAYER .....................33

Audio Video Settings............................................... 33

Quick Start............................................................... 35

Auto Power Off........................................................ 35

HDMI Control ......................................................... 35

Playback Setting ...................................................... 35

Communication Setup ............................................. 36

Version ..................................................................... 39

USB Memory Management..................................... 39

Software Update ...................................................... 39

System Reset............................................................ 39

CHANGING THE SETTINGS WHEN

CONNECTING AN HDMI OR

COMPONENT CABLE....................................41

TROUBLESHOOTING........................................42

Receiver (R-840)...................................................... 42

Remote control ........................................................ 44

BD player (BD-940) ................................................ 44

Network ................................................................... 46

Messages Relating to BD disc and DVD disc ......... 46

ABOUT THE JPEG FILE FORMAT .................47

NOTES ABOUT HANDLING DISCS ................48

GLOSSARY...........................................................48

SPECIFICATIONS ...............................................49

LANGUAGE, COUNTRY LISTS........................51

Language list............................................................ 51

Country list .............................................................. 51

(at the end of this manual)

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATIONS

TUNER OPERATIONS

OTHER OPERATIONS

ADDITIONAL INFORMATION

Information about software .................................. i

FEATURES

2 En

INTRODUCTION

Receiver (R-840)

• Minimum RMS output power per channel

65W + 65W (6Ω, 1kHz, 10% THD)

• 30-station FM preset tuning

• iPod playability (with rechargeable function)

• Pure Direct mode

• Adjustable Display Brightness

BD player (BD-940)

• Plays Blu-ray Discs, DVDs, Audio CDs

• Supports BD-LIVE. When using a BD-LIVE

compatible disc, you can connect the BD player

to the Internet and download various data

• Supports HDMI control function. You can

operate the receiver and BD player with a TV

remote control connected by an HDMI cable

• Linked operation with the receiver such as

Pure Direct mode, Adjustable Display

Brightness and INPUT mode

■ About this manual

• In this manual, “R-840” is described as “receiver” and “BD-940” is described as “BD player”.

• This manual describes how to operate the system using a remote control except when it is not available. Some of these operations are

also available using the front panel buttons.

• y indicates a tip for your operation.

• Notes contain important information about safety and operating instructions.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

This product includes the following accessories. Before connecting this system, make sure you received all of the following parts.

FEATURES

SUPPLIED ACCESSORIES

1234

56

90

7 8

E

NT

E

RCL

E

AR

MUT

E

NT

E

R

VOLUME

AUX

TUN

E

R

iPod SHUFFLE

R

EPE

AT

MENU

ENTER

E

O

NM

O

N

O

M

E

M

O

R

Y

PRESET TUNING

DISC

DISPLAY TIMER SLEEP DIMMER

OPTION PURE DIRECT

AUDI O SUBTITLE ANGLE

REPEAT

ON SCREEN

RETURN

PinP SETUP

A B C D

EXIT

TOP MENU/TITLE LIST

POP UP MENU

Indoor FM antenna

Batteries (x2)

(AAA, R03, UM-4)

Remote

control

* The Dock cover is supplied with this unit to cover

the iPod dock when not in use.

iPod

INPUT

VOLUME

Dock cover*

Receiver

System control

cable (0.6 m)

RCA stereo

cable (1.0 m)

Composite video

cable (1.5 m)

3 En

English

INTRODUCTION

• The following discs can be played back in this Player.

Do not use an 8 cm (3”) to 12 cm (5”) adapter.

• Use discs that conform to compatible standards as

indicated by the presence of official logos on the disc

label. Playback of discs not complying with these

standards is not guaranteed. In addition, the image

quality or sound quality is not guaranteed even if the

discs can be played back.

*1 This Player has been designed on the premise of playing back

Audio CDs that comply with CD (Compact Disc) standards.

CDs containing a signal for the purpose of protecting

copyrights (copy control signal) may not be able to be played

back with this Player.

*2 See “ABOUT THE JPEG FILE FORMAT” on page 47.

• BD/DVD video players and discs have region codes,

which dictate the regions in which a disc can be played.

• BD/DVD Video operations and functions may be

different from the explanations in this manual and

some operations may be prohibited due to disc

manufacturer’s settings.

• If a menu screen or operating instructions are displayed

during playback of a disc, follow the operating

procedure displayed.

• The audio component of a DVD video recorded at 96

kHz (Linear PCM) will be output as 48 kHz audio

during playback.

Notes

• Playback for some of the discs in the left side column tables

may not be possible depending on the disc.

• “Finalize” refers to a recorder processing a recorded disc so that

it will play in other BD players/recorders as well as this player.

Only finalized DVD discs will play back in this player. (This

player does not have a function to finalize discs.)

The following discs cannot be played back or will not play

back properly on this Player. If such a disc is mistakenly

played back, speaker damage may occur.

Discs with unusual shapes cannot be

played.

Discs with unusual shapes (heart-shaped or hexagonal

discs, etc.) cannot be used. The use of such discs will

cause malfunction.

The following BD/DVD video discs cannot

be played.

• Discs not match the region code/number of this Player.

• Discs produced illegally.

• Discs recorded for commercial use.

ABOUT DISCS

Types of Discs that Can Be Used

with This Player

Disc Type

Recording

Format

Contents Disc Size

BD video -- Audio +

Video

(Movie)

12 cm (5”)

8 cm (3”)

BD-RE DL

BD-R DL

BDMV

format

DVD Video Video format Audio +

Video

(Movie)

12 cm (5”)

8 cm (3”)

DVD+RW/

DVD+R

DVD+R DL

DVD-R DL

DVD-RW/

DVD-R

Video/VR/

AV C H D

format

(finalized disc

only)

Audio +

Video

(Movie)

12 cm (5”)

8 cm (3”)

Audio CD

*1

Audio CD

(CD-DA)

Audio 12 cm (5”)

8 cm (3”)

CD-RW/CD-R Audio CD

(CD-DA)

Audio

JPEG

*2

Still image

(JPEG file)

Region management information

Model BD-Video DVD-Video

Europe Region code “B” or

“ALL”

Region number “2”

or “ALL”

Russia Region code “C” or

“ALL”

Region number “5”

or “ALL”

2

ALL

5

ALL

Discs that Cannot Be Used with

This Player

CDG, Video CD, Photo CD, CD-ROM, SVCD,

SA-CD, PD, CDV, CVD, DVD-RAM, DVD-Audio,

BD-RE with the cartridge, CD-MP3, CD-WMA

CONTROLS AND FUNCTIONS

4 En

■ Front panel

1 INPUT

Selects an input source.

2 On/Standby indicator

Lights up in green when the receiver is turned on. Lights

up in amber when the receiver is in standby mode.

3 TP indicator

Lights up when the receiver is receiving a Radio Data

System station which contains the TP (Traffic Program)

data service (☞p.29).

4 Remote control sensor

Receives signals from the remote control.

5 PRESET indicator

Lights up when you select preset radio stations (☞p.27).

6 TUNED indicator

Lights up when the receiver is tuned into a station.

7 STEREO indicator

Lights up when the receiver is receiving a strong signal

from an FM stereo broadcast.

8 SLEEP indicator

Lights up when the sleep timer is on (☞p.31).

9 Front panel display

Shows the various information such as the tuning

frequency.

0 VOLUME

Adjusts the volume level.

A (On/Standby)

Turns the receiver on or sets it to standby mode.

B PHONES jack

Outputs audio signals for private listening with

headphones.

C TIMER indicator

Lights up when the timer is set (☞p.30).

D BASS

Adjusts the low frequency response (☞p.15).

E TREBLE

Adjusts the high frequency response (☞p.15).

F BALANCE

Adjusts the audio output balance of the left to right

speakers to compensate for imbalances caused by speaker

locations or listening room conditions.

G PRESET d / u

Selects a preset station. The input source is changed to

FM. Operable even when the receiver is in standby mode

(☞p.27).

H PURE DIRECT

Turns on or off Pure Direct mode (☞p.15).

When Pure Direct mode is on, the indicator lights up in

blue.

I h / e

Starts and pauses the playback of iPod. The input source is

changed to iPod. Operable even when the receiver is in

standby mode.

J iPod dock

Connect your iPod (☞p.10).

CONTROLS AND FUNCTIONS

Receiver (R-840)

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

PRESET

TP

TUNED

STEREO SLEEP

kHz MHz

iPod

TIMER

1

@

IJBCD E F G H

234 5 67 98

A

Top viewFront view

5 En

CONTROLS AND FUNCTIONS

English

INTRODUCTION

■ Front panel

1 Disc tray

Holds a disc to be played back.

2 p (play) indicator

Appears during playback.

3 REP OFF S ALL A-B indicator

Lights up when Repeat play mode is selected.

4

Opens and closes the disc tray.

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to DISC.

5

Stops playback (☞p.17).

6 (On/Standby)

Turns on the BD player or sets it to standby mode.

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to DISC.

y

If the BD player does not operate properly for some reason, you

can reboot it by holding down this button for about 10 seconds

and pressing it again.

7 QUICK indicator

Light up in standby mode when Quick Start function is on

(☞p.35).

Flashes after you connect the power cable to the AC wall

outlet until the BD player enters standby mode.

8 e (pause) indicator

Lights up while the BD player is paused.

9 Front panel display

Shows the current status of the BD player.

0

Returns to the beginning of the current chapter or track.

Press and hold to fast reverse. Press twice to skip to the

previous chapter or track (☞p.18).

A

Starts or pauses playback (☞p.17).

When this button is pressed during standby mode, the

receiver automatically turns on and the input source

changes to DISC, whichever was last selected.

B

Skips to the next chapter or track. Press and hold to fast

forward (☞p.18).

BD player (BD-940)

QUICK

12 45

7

98

6

3

AB

@

PROG RANDOMMP3 WMA TRACK TOTAL REMAIN REP OFF S ALL A-B

6 En

CONTROLS AND FUNCTIONS

This remote control can operate the system components

(including tuner functions) and an iPod stationed in the

iPod dock on the top of the receiver.

To operate the BD player, tuner functions, or an iPod

using the remote control, you need to set the receiver to

corresponding input mode (☞8Input selection keys).

To operate your iPod

Press the corresponding iPod operation key on the remote

control.

The iPod operation keys are indicated with in the

section below. See page 32 for more information on the

operation of your iPod.

1 Infrared signal transmitter

Sends signals to the system you want to control.

2 (On/Standby)

Turns the system on or sets it to standby mode.

3 MENU

Returns to the upper level in the iPod menu.

4

Skips to the next song. Press and hold to fast forward.

5

Skips to the beginning of the current track. Press twice to

skip back to the previous track. Press and hold to fast

reverse.

6 ENTER

Press ENTER to enter the selected group. (Pressing

ENTER starts playback when a song is selected.)

7

Starts or Pauses Playback.

8 Input selection keys

Selects the input source on the receiver.

When selecting an input source, press the corresponding

input selection key (or turn INPUT on the front panel).

The name of the corresponding input source appears on

the front panel display of the receiver.

y

When DISC is selected as an input source, the BD player turns on

automatically and when other input source is selected, the BD

player sets to standby mode.

9 MEMORY

Stores a preset station in the memory (☞p.27). Starts

Automatic preset tuning (☞p.26).

0 MONO

Sets FM broadcasting receiving mode to monaural mode.

Remote control

1234

56

90

78

E

NT

E

RCL

E

AR

MUT

E

NT

E

R

VOLUME

AUX

TUN

E

R

iPod SHUFFLE

R

EPE

AT

MENU

ENTER

E

O

NM

O

N

O

M

E

M

O

R

Y

PRESET TUNING

DISC

DISPLAY TIMER SLEEP DIMMER

OPTION PURE DIRECT

AUDIO SUBTITLE ANGLE

REPEAT

ON SCREEN

RETURN

PinP SETUP

A B C D

EXIT

TOP MENU/TITLE LIST

POP UP MENU

J

1

M

N

O

P

Q

R

S

t

U

V

W

X

Y

Z

[

\

]

`

a

b

c

d

f

e

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

7 En

CONTROLS AND FUNCTIONS

English

INTRODUCTION

A TP

Enters TP (Traffic Program) data service receiving mode

(☞p.29).

B TIMER

Shows the current time on the front panel display of the

receiver.

And sets the clock (☞p.12) or the timer (☞p.30).

C DISPLAY

Switches the information shown on the front panel display

of the receiver or the TV screen for the BD player (☞p.23,

p.28).

D OPTION

Enters option menu mode.

See pages 27, 29 and 41 for option menu items.

E A/B/C/D

Used when input source is set to DISC.

F TOP MENU/TITLE LIST

Displays the BD/DVD’s top menu (☞p.18).

G , , , , ENTER

For selecting and confirming an item.

H EXIT

Exits the menu screen.

I

Pauses playback (☞p.17).

J

Stops playback (☞p.17).

K ,

Rewind and fast-forward.

L Numeric keys

Input numbers.

M AUDIO

Selects the audio format and soundtrack (☞p.19).

N SUBTITLE

Selects subtitles (☞p.19).

O P in P

Uses the Picture in Picture function (☞p.24).

P REPEAT

Selects Repeat Play mode (☞p.19).

Q

Opens and closes the disc tray.

R ,

Press or to switch an item in the selected group

(☞p.32).

S SHUFFLE

Selects mode of Shuffle Play (☞p.32).

T REPEAT

Selects mode of Repeat Play (☞p.32).

U TUNING

Press TUNING to Manual tuning and press and

hold TUNING to Automatic tuning (☞p.26).

V PRESET u / d

Select a preset station (☞p.27).

W DIMMER

Changes the brightness of the front panel display (☞p.16).

X PURE DIRECT

Turns on or off Pure Direct mode (☞p.15).

Y SLEEP

Sets the sleep timer on the system (☞p.31).

Z POP UP MENU

Displays the BD’s pop-up menu (☞p.18).

[ VOLUME +/–

Adjusts the overall volume level on the receiver.

\ RETURN

Returns to the previous menu (☞p.17).

]

Starts playback (☞p.17).

` MUTE

Turn off the volume (☞p.16).

a ,

Skips to the beginning of the current or next chapter or

track.

b CLEAR

Clears an entry.

c ENTER

Confirms an entry.

d ON SCREEN

Displays disc information on-screen (☞p.23).

e ANGLE

Selects an camera angle (☞p.19).

f SETUP

Displays the Setup menu (☞p.13).

/

d

/

d

/

d

PREPARATIONS

8 En

PREPARATION

Make sure you read the following procedure and note carefully before connecting the system. The remote control

and linked operation of the system only work when the receiver and the BD player are connected via

the system control cable. For information on the speakers (NS-BP300), refer to the owner’s manual supplied with it.

Connecting the system

1 Connect the AUDIO IN ( PLAYER L/R) jacks of the receiver to the AUDIO OUT ( L/R) jacks of the BD player

using the supplied audio RCA stereo cable.

2 Connect the SYSTEM CONNECTOR ( TO:PLAYER) jack of the receiver to the SYSTEM CONNECTOR

( TO:RECEIVER) jack of the BD player using the supplied system control cable.

3 Connect the speaker terminals (L) of the receiver to the speaker terminals of the left speaker and the speaker terminals

(R) of the receiver to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set

(NS-BP300).

4 Connect the supplied FM antenna to the ANTENNA jack.

• Do not connect this unit or other components to the main power until all connections between components are complete.

• Do not let the bare speaker wires touch each other or any metal part of the receiver. This could damage the receiver and/or the

speakers.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be

heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,

refer to the owner’s manual for each of your components.

Notes

• The system control connection is used to transmit the remote control signals from the receiver to the BD player.

• When connecting speakers other than NS-BP300, use speakers having more than 6Ω impedance.

• If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use

commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.

PREPARATIONS

Connecting speakers/external components/antennas

CAUTION

A A

B

Receiver (R-840)

(Europe model)

BD player (BD-940)

Left speaker

(NS-BP300)

Right speaker

(NS-BP300)

RCA stereo cable

(supplied)

System control cable

(supplied)

TV etc.

Subwoofer

Audio

out

RCA

stereo

cable

PREPARATIONS

9 En

English

PREPARATION

Connecting a TV to the system

1 Connect the system and your TV via the HDMI jack, COMPONENT jacks or VIDEO jack of the BD player and the

corresponding jack(s) of your TV.

2 Set “TV screen” according to your TV (see “Setting the TV display” on page 13).

When connecting the system and your TV via the COMPONENT jacks, set the BD player as described in “Video Out

Select” (☞p.33).

When connecting the system and your TV via the HDMI jacks, set “HDMI Video Out” and “Audio Out” of “Audio

Video Settings” in the “Settings” menu (☞p.33, 34).

When connecting the system and your TV via the HDMI jacks, use HIGH SPEED HDMI cables that have the HDMI

logo (as shown on the cover).

You can output audio from the DIGITAL OUT jack and record it digitally on another device, or transmit audio signal to

an AV receiver or decoder to enjoy multichannel source audio.

After you made all connections, connect the power cables of this system and other components to AC wall outlets.

Connecting a recorder (CDR, MDR, etc.), AV receiver or decoder (CDR,

MDR, etc.)

Connecting power cables

BD player (BD-940)

Composite video cable

(supplied)

To AC wall outlet

Receiver (R-840)

BD player (BD-940)

PREPARATIONS

10 En

The receiver is equipped with the iPod dock on the top

panel where you can station your iPod and control

playback of your iPod using the supplied remote control.

Use this receiver with iPod dock adapter (supplied with

your iPod or commercially available) appropriate for your

iPod. If you use this receiver without using an appropriate

iPod dock adapter, loose connection may result.

y

When the receiver is turned on or in standby mode, connect the

iPod during the playback. The receiver automatically starts

playback of iPod (for the fifth or later generation of iPod, iPod

touch, iPod Classic, or iPod nano).

Notes

• Only iPod (Click and Wheel), iPod nano, iPod Classic, iPod

mini and iPod touch are supported.

• Do not connect any iPod accessories (such as headphones, a

wired remote control, or an FM transmitter) to your iPod when

it is stationed in the iPod dock.

• Unless your iPod is firmly stationed in the iPod dock, audio

signals may not be output properly.

• Once the connection between your iPod and the receiver is

complete and the receiver is set to iPod mode (☞p.6),

“CONNECTED” appears on the front panel display. If the

connection between your iPod and the receiver fails, a status

message appears on the front panel display. For a complete list

of connection status message, see the iPod section in

“TROUBLESHOOTING” (☞p.42).

• When your iPod is stationed in the iPod dock of the receiver,

your iPod can be charged automatically even when the receiver

is in standby mode.

• You can disconnect the iPod during the playback.

You can enjoy a variety of contents with interactive

functions by connecting to the internet when playing BD-

LIVE compatible discs. See pages 24 and 36 regarding

further information on BD-LIVE functions.

Be sure to turn off the BD player and the equipment

before making any connections.

Notes

• You can connect a USB memory device (2GB or greater and

formatted with FAT 32/16) to the USB BD STORAGE/

SERVICE terminal to save the BD-LIVE data or to update the

software of the BD player.

• A broadband internet connection is required.

• When using a broadband internet connection, a contract with an

internet service provider is required. For more details, contact

your nearest internet service provider.

• Refer to the operation manual of the equipment you have as the

connected equipment and connection method may differ

depending on your internet environment.

• Use a network cable/router supporting 10BASE-T/100BASE-

TX/1000BASE-T.

• Use only an STP (shielded twisted pair) network cable.

■ After connecting

• Perform the communication setting (☞p.36).

• Load a BD-LIVE compatible disc and play back the

contents (☞p.24).

Connecting an iPod™

iPod

INPUT

PHONES

BASS

-+ -+ LR

TREBLE BALANCE

PRESET PURE DIRECT

VOLUME

MIN MAX

Receiver

iPod

iPod dock adapter

Connecting to the Internet

CAUTION

LAN

BD player

Internet

Network cable

(commercially available)

2

To LAN

terminal

PC

3

To USB BD

STORAGE/

SERVICE

terminal

USB memory device

(commercially available)

Modem

Hub or

broadband

router

1

To NETWORK

terminal

PREPARATIONS

11 En

English

PREPARATION

■ Notes on batteries

• Change both batteries when the operation range of the

remote control decreases.

• Use AAA, R03, UM-4 batteries.

• Make sure that the polarities are correct. See the

illustration inside the battery compartment.

• Remove the batteries if the remote control is not to be

used for an extended period of time.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline

and manganese batteries) together. Read the packaging

carefully as these different types of batteries may have

the same shape and color.

• If the batteries have leaked, dispose of them

immediately. Avoid touching the leaked material or

letting it come into contact with clothing, etc. Clean the

battery compartment thoroughly before installing new

batteries.

• Do not throw away batteries with general house waste;

dispose of them correctly in accordance with your local

regulations.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of the receiver during

operation.

Notes

• The area between the remote control and the receiver must be

clear of large obstacles.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– high humidity, such as near a bath

– high temperature, such as near a heater or a stove

– extremely low temperatures

– dusty places.

• Do not expose the remote control sensor to strong lighting, in

particular, an inverter type fluorescent lamp; otherwise, the

remote control may not work properly. If necessary, position the

system away from direct lighting.

Installing the batteries in the

remote control

1

3

2

Using the remote control

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

1234

56

90

78

ENTER CLEA R

MUTE

ENTER

VOLUME

AUX

TUNER

iPod SHUFFLE

REPEAT

MENU

ENTER

EON MONO

MEMORY

PRESET TUNING

DISC

DISPLAY TIMER SLEEP DIMMER

OPTION PURE DIRECT

AUDIO SUBTITLE ANGLE

REPEAT

ON SCREEN

RETURN

PinP SETUP

A B C D

EXIT

TOP MENU/TITLE LIST

POP UP MENU

30˚ 30˚

Within 6 m

(20 feet)

Receiver (R-840)

PREPARATIONS

12 En

Before starting playback operation, follow the procedure

below to adjust the clock setting of the receiver.

Notes

• Use the remote control to set the clock. You cannot set the clock

with the buttons on the receiver.

• The receiver supports 24-hour clock display.

• If you do not touch any key for 90 seconds, the receiver returns

to normal mode.

1 Press to turn the receiver on.

The front panel display lights up.

2 Press TIMER to show the current time.

If the clock is not set, “SET TIME” flashes on the

display.

Press ENTER to proceed to step 3.

3 Press / to select “TIME”, and press

ENTER.

The receiver enters clock setting mode. The hour

digits start flashing.

4 Set the hour using / , and press .

The minute digits start flashing.

5 Set the minutes using / , and press

ENTER.

The hour and minute digits start flashing.

To change the hour or minutes again, press or ,

do steps 4 and 5, and proceed to step 6.

6 Press ENTER.

The clock is set.

The hour and minute segments stop flashing and

remain on. The receiver returns to normal mode.

y

You can return to the previous screen by pressing or

RETURN.

Adjusting the Clock

A B C D

EXIT

TOP MENU/TITLE LIST

POP UP MENU

TIMER

ENTER

,

RETURN

Flashes

SETTING THE SYSTEM

13 En

English

PREPARATION

Make sure that you have completed all the necessary

connections (see “Connecting a TV to the system” on

page 9).

1 Turn on the TV to which the BD player is

connected.

Select the TV input to match the input connected to

the BD player.

2 Press to turn on the receiver.

3 Press DISC.

Set the aspect ratio of the BD player according to the TV

you have connected (☞p.33).

1 Press SETUP.

The setup menu appears on the screen.

2 Press /// to select “Settings”, and then

press ENTER.

3 Press / to select “Audio Video Settings”,

and then press ENTER.

4 Press / to select “TV Aspect Ratio”, and

then press ENTER.

5 Press / to select the aspect ratio of the TV

and then press ENTER.

For details on the aspect ratio option, see page 33.

6 Press SETUP or EXIT to exit the setup menu.

y

You can return the previous menu by pressing RETURN.

You can select your preferred language settings so that the

BD player will automatically switch to your preferred

language whenever you load a disc. If the language

selected is not available on the disc, the disc’s default

setting language will be used instead. The OSD (on-screen

display) language for the BD/DVD setup menu will

remain as you set it, regardless of various disc languages.

1 Press SETUP.

2 Press / // to select “On Screen

Language”, and then press ENTER.

3 Press / to select a language, and then

press ENTER.

SETTING THE SYSTEM

Turn on the TV and the system

Setting the TV display

EXIT

TOP MENU/TITLE LIST

POP UP MENU

SETUP

, , , ,

ENTER

Settings

Picture

On Screen Language

Displays The Title List

On-screen display (OSD) language

Audio Video Settings

Quick Start

HDMI Control

Playback Setting

Communication Setup

Version

USB Memory Management

Software Update

System Reset

SETTING THE SYSTEM

14 En

1 Press SETUP.

2 Press /// to select “Settings”, and then

press ENTER.

3 Press / to select “Playback Setting”, and

then press ENTER.

4 Press / to select “Disc Language”, and

then press ENTER.

5 Press / to select the item below.

• Subtitle

• Audio

•Menu

6 Press / to select a language, and then

press ENTER.

Audio, Subtitle and Disc menu

languages

SYSTEM OPERATIONS

15 En

English

BASIC

OPERATIONS

BASIC OPERATIONS

Follow the procedure below to select an input source and adjust the sound settings on the system.

1 Press (On/Standby) to turn on the receiver.

Depending on input mode of the receiver, the BD

player also turns on by the system control connection

(☞p.8). The front panel display lights up.

2 Press one of the input selection keys (or

rotate INPUT on the front panel) to select the

desired input source.

3 Start playback on the selected source

component or select a radio station.

For information on the disc playback, see page 17,

and for information on tuning, see page 26.

4 Press VOLUME +/– (or turn VOLUME on the

front panel) to adjust the volume to the

desired output level.

5 Rotate BASS, TREBLE, or BALANCE on the

front panel of the receiver to adjust the

following settings.

BASS: Adjusts the low frequency response.

TREBLE: Adjusts the high frequency response.

BALANCE: Adjusts the volume level of each left

and right speaker channel.

■ Pure Direct mode

Pure Direct mode bypasses the tone control circuit and

turns off the front panel display, allowing you to enjoy

pure high-fidelity sound.

Press PURE DIRECT (or PURE DIRECT on the

front panel) to turn on Pure Direct mode.

The front panel display automatically turns off. PURE

DIRECT on the front panel is backlit in blue.

Notes

• If you carry out operations while Pure Direct mode is turned on,

the front panel display of the receiver lights up briefly to

acknowledge the command.

• While the Pure Direct mode is turned on, neither BASS,

TREBLE, nor BALANCE is available.

To turn off Pure Direct mode

Press PURE DIRECT again. The PURE DIRECT

backlight turns off and the front panel display turns on.

SYSTEM OPERATIONS

INPUT

BASS

PHONES

VOLUME

MIN MAX

TREBLE BALANCE

PRESET PURE DIRECT

LR

TP

TIMER

QUICK

INPUT

(On/Standby) VOLUME

PURE

DIRECTBASS BALANCE

TREBLE

A B C D

EXIT

TOP MENU/TITLE LIST

POP UP MENU

(On/Standby)

VOLUME +/–

Input selection

keys

PURE DIRECT

MUTE

Basic system operations

SYSTEM OPERATIONS

16 En

■ Muting the sound (MUTE)

Press MUTE to reduce the current volume level

by approximately 20dB.

“MUTE ON” appears on the front panel display.

Press MUTE again to restore the audio output to the

previous volume level.

You can dim the front panel display of the receiver. The

front panel display of the BD player also dims by the

system control connection (☞p.8). (The default setting is

“DIMMER OFF”.)

Press DIMMER.

You can choose your desired brightness of the front panel

display between normal (bright), mid dim, and dim.

You can connect your headphones to the PHONES jack on

the front panel of the receiver.

The sound from the speakers and the subwoofer stops.

Changing the brightness of the

front panel display

To use headphones

DIMMER

INPUT

PHONES

Sayfa yükleniyor ...

Yamaha MCR-940 El kitabı

Yamaha MCR-940 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler