OWNER'S MANUAL
MODE D'EMPLOI
MANUAL DE INSTRUCCIONES
UATLK
RECEIVER/CD PLAYER
AMPLI-TUNER/LECTEUR CD
i En
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with dry cloth.
7 Do not block any ventilation openings. Install in accordance with
the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9 Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
13 Unplug this apparatus during lightning storms or
when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has
been dropped.
IMPORTANT SAFETY INSTRUCTIONS
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, Yamaha and the Electronic Industries Association’s Consumer Electronics Group
recommend you to avoid prolonged exposure from excessive volume levels.
ii En
FCC INFORMATION (for US customers)
1 IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC,
to use the product.
2
IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
3 NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations does not guarantee
that interference will not occur in all installations. If
this product is found to be the source of interference,
which can be determined by turning the unit “OFF”
and “ON”, please try to eliminate the problem by using
one of the following measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch
(circuit breaker or fuse) circuits or install AC line
filter/s.
In the case of radio or TV interference, relocate/
reorient the antenna. If the antenna lead-in is 300 ohm
ribbon lead, change the lead-in to coaxial type cable.
If these corrective measures do not produce
satisfactory results, please contact the local retailer
authorized to distribute this type of product. If you can
not locate the appropriate retailer, please contact
Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe
Ave, Buena Park, CA 90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
R-1330 CD-1330
● The label is located on the bottom of the unit. (U.S.A and Canada models only)
iii En
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this unit (R-1330 and CD-1330) in a well ventilated, cool,
dry, clean place with at least 10 cm on the top (except for CD-
1330), 10 cm on the left and right, and 10 cm at the back of this
unit — away from direct sunlight, heat sources, vibration, dust,
moisture, and/or cold.
3 Locate this unit away from other electrical appliances, motors, or
transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from cold
to hot, and do not locate this unit in an environment with high
humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire,
damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this
unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage
to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to this
unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc.
in order not to obstruct heat radiation. If the temperature inside
this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
7 Do not plug in this unit to a wall outlet until all connections are
complete.
8 Do not operate this unit upside-down. It may overheat, possibly
causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp
the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage
the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit
with a higher voltage than specified is dangerous and may cause
fire, damage to this unit, and/or personal injury. Yamaha will not
be held responsible for any damage resulting from use of this unit
with a voltage other than specified.
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or this unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed.
The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time (i.e.
vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit is
faulty.
17 Before moving this unit, press ON/STANDBY, OFF to turn off
the system, and disconnect the AC power plug from the wall
outlet.
18 Condensation will form when the surrounding temperature
changes suddenly. Disconnect the power cable from the outlet,
then leave this unit alone.
19 When using this unit for a long time, this unit may become warm.
Turn the power off, then leave this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug
can be reached easily.
21 The batteries shall not be exposed to excessive heat such as
sunshine, fire or the like.
22 Excessive sound pressure from earphones and headphones can
cause hearing loss.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt to
service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into the wall outlet, do not place your
eyes close to the opening of the disc tray and other openings to
look into inside.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit itself
is turned off by . This state is called the standby mode. In
this state, this unit is designed to consume a very small
quantity of power.
The laser component in this product is capable of emitting
radiation exceeding the limit for Class 1.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
1 En
English
PREPARATIONINTRODUCTION
TUNER
OPERATIONS
OTHER
OPERATIONS
ADDITIONAL
INFORMATION
BASIC
OPERATIONS
FEATURES............................................................. 2
SUPPLIED ACCESSORIES ................................. 2
CONTROLS AND FUNCTIONS ......................... 3
Receiver (R-1330) ..................................................... 3
CD player (CD-1330) ................................................ 4
Remote control........................................................... 5
CONNECTING THE EXTERNAL
COMPONENTS WITH THE SYSTEM .......... 9
CONNECTING ANTENNAS.............................. 10
CONNECTING THE POWER CABLES .......... 10
CONNECTING THE iPod™ AND THE USB
DEVICE............................................................. 11
Connecting an iPod™.............................................. 11
Connecting USB devices......................................... 11
SYSTEM OPERATIONS .................................... 12
Basic system operations........................................... 12
Changing the brightness of the front panel display ..... 13
Setting the sleep timer ............................................. 13
To use headphones................................................... 13
DISC AND USB DEVICE OPERATIONS ........ 14
Playback operations................................................. 14
Switching the playback information display ........... 15
Repeating playback (Repeat Play)........................... 16
Playing back randomly (Random Play)................... 16
FM/AM TUNING ................................................. 17
Automatic tuning ..................................................... 17
Manual tuning.......................................................... 17
Automatic preset tuning (FM only)......................... 17
Manual preset tuning ............................................... 18
Selecting preset stations........................................... 18
CONTROLLING iPod™......................................19
Using iPod™ ........................................................... 19
TROUBLESHOOTING .......................................20
Receiver (R-1330) ................................................... 20
CD player (CD-1330) .............................................. 21
Remote control ........................................................ 22
NOTES ABOUT DISCS/MP3, WMA FILES.....23
GLOSSARY...........................................................25
Audio information ................................................... 25
Copyright and logo marks ....................................... 25
SPECIFICATIONS...............................................25
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATIONS
TUNER OPERATIONS
OTHER OPERATIONS
ADDITIONAL INFORMATION
■ Ab
ou
t
thi
s manua
l
• In this manual, “R-1330” is described as “receiver” and “CD-1330” is described as “CD player”.
• This manual describes how to operate the system using a remote control except when it is not available. Some of these operations are
also available using the front panel buttons.
• y indicates a tip for your operation.
• Notes contain important information about safety and operating instructions.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and the product, the product has priority.
FEATURES
2 En
Receiver (R-1330)
• Minimum RMS output power per channel
60 W + 60 W (6 Ω, 1 kHz, 0.5% THD)
• 30-station FM/AM preset tuning
• iPod playability (with rechargeable function)
• Pure Direct mode
• Adjustable Display Brightness
CD player (CD-1330)
• Plays Audio CDs, MP3/WMA discs
• CD-R, CD-RW Disc Playability
• MP3/WMA file playability stored on USB
device
• Linked operation with the receiver such as
Pure Direct mode, Adjustable Display
Brightness and INPUT mode
This product includes the following accessories. Before connecting this system, make sure you received all of the following parts.
FEATURES
SUPPLIED ACCESSORIES
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
Indoor FM antenna
System control
cable (0.6 m)
Batteries (x2)
(AA, R6, UM-3)
Remote
control
RCA stereo
cable (1.0 m)
Dock cover
ON
/
STANDBY
OFF
PHONES
VOLUME
INPUT
PURE
DIRECT
TUNER PRESET
MIN
MAX
iPod
When the Dock cover is covered.
AM loop antenna
(Australia and
Korea models)
(Other models)
Clamp filter (x2)
Latch
Coil the speaker cable around
the clamp filter and close it
until the latch is locked.
(U.S.A and Canada
models only)
3 En
English
INTRODUCTION
■ Front panel
1 ON/STANDBY, OFF
Turns the receiver to ON/STANDBY or OFF.
2 ON/STANDBY indicator
Lights up in green when the receiver is turned on. Lights
up in amber when the receiver is in standby mode.
The indicator goes off when the receiver is turned off.
3 Front panel display
Shows the various information such as the tuning
frequency.
4 PRESET indicator
Lights up when you select preset radio stations (see
page 18).
5 TUNED indicator
Lights up when the receiver is tuned into a station.
6 STEREO indicator
Lights up when the receiver is receiving a strong signal
from an FM stereo broadcast.
7 SLEEP indicator
Lights up when the sleep timer is on (see page 13).
8 PHONES
Outputs audio signals for private listening with headphones.
9 Remote control sensor
Receives signals from the remote control.
0 INPUT
Selects an input source.
A PURE DIRECT
Turns on or off the Pure Direct mode (see page 12).
When PURE DIRECT mode is on, the indicator above
lights up.
B TUNER PRESET /
The input source is changed to FM/AM. Selects a preset
station. Operable even when the receiver is in standby mode.
C VOLUME
Adjusts the volume level.
D h / e
The input source is changed to iPod. Starts and pauses the
playback of iPod. Operable even when the receiver is in
standby mode.
E iPod terminal
Connect your iPod (see page 11).
CONTROLS AND FUNCTIONS
Receiver (R-1330)
iPod
D
E
ON
/
STANDBY
OFF
PHONES
VOLUME
INPUT PURE
DIRECT
TUNER PRESET
MIN MAX
PRESET
TUNED
STEREO SLEEP
kHz MHz
8 9
0
A
1
B
C
2
3
4
56
7
Top view
Front view
4 En
CONTROLS AND FUNCTIONS
■ Front panel
1 ON/STANDBY, OFF
Turns the CD player to ON/STANDBY or OFF.
2 ON/STANDBY indicator
Lights up in green when the CD player is turned on. Lights
up in amber when the CD player is in standby mode.
The indicator goes off when the CD player is turned off.
3 USB indicator
Lights on when the CD player is in USB mode and goes
off when the CD player is in CD mode. Blinks when the
CD player is reading the USB device.
4 Disc tray
Holds a disc to be played back.
5
Opens and closes the disc tray.
When this button is pressed during standby mode, the
receiver automatically turns on and the input changes to
CD.
6 USB Port
Connect your USB device.
7 Remote control sensor
Receives signals from the remote control.
8 Front panel display
Shows the current status of the CD player.
9 RANDOM indicator
Lights up the icon for the selected Random Play mode.
0 REP OFF S ALL indicator
Lights up the icon for the selected Repeat Play mode.
A
Starts or pauses playback (see page 14).
When this button is pressed during standby mode, the
receiver automatically turns on and the input changes to
either CD or USB whichever was the last selected.
B
Stops playback (see page 14).
C
Skips to the beginning of the current track. Press and hold
to fast reverse. Press twice to skip to the previous track
(see page 14).
D
Skips to the next track. Press and hold to fast forward (see
page 14).
CD player (CD-1330)
USB
ON
/
STANDBY
OFF
6 7
14
5
AB
C D
0
2 3
8
9
5 En
CONTROLS AND FUNCTIONS
English
INTRODUCTION
■ Common functions
This remote control can operate the system components
(including tuner functions) and an iPod stationed in a
terminal on the top of the receiver.
To operate the CD player, tuner functions, or an iPod
using the remote control, you need to set the receiver to
the corresponding input mode.
To switch the input mode of the receiver
Press the corresponding input selection key on the remote
control (or rotate INPUT on the front panel).
The name of the corresponding input source appears in the
front panel display of the receiver.
y
When CD or USB is selected as an input source, the CD
player turns on automatically and when other input source
is selected, the CD player sets to standby mode.
Operations common to all modes
The following operations are available for the receiver
when it is set to any input mode.
1 Infrared signal transmitter
Sends signals to the system you want to control.
2 (standby/on)
Turns the system on or sets it to the standby mode.
Even when the system is in standby mode, it consumes a small
amount of power in order to receive infrared-signals from the
remote control.
3 Input selection keys
Select the input source on the receiver.
4 PURE DIRECT
Turns on or off the Pure Direct mode (see page 12).
5 VOL +/–
Adjusts the overall volume level on the receiver.
6 TONE/BALANCE /
Adjusts the audio quality (see page 12).
7 SLEEP
Sets the sleep timer on the system (see page 13).
8 MUTE
Turn off the volume (see page 12).
9 DIMMER
Changes the brightness of the front panel display (see
page 13).
Remote control
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
TUNING
MEMORY
Input
selection
keys
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
5
3
1
2
7
9
4
8
6
Note
6 En
CONTROLS AND FUNCTIONS
■ CD/USB mode
Operations available in CD/USB mode
The following operations are available for the CD player
if the CD player is connected to the receiver with the
system control connection (see page 9).
y
Press CD or USB to set the receiver to the CD or USB
mode before carrying out the following operations.
1 REPEAT
Selects the Repeat Play mode (see page 16).
2 ,
Skips to the beginning of the current track or next track.
Press and hold to fast reverse or fast forward (see
page 14). Press twice to skip back to the previous
track.
3 DISPLAY
Switches the information shown in the front panel display
of the CD player (see page 15).
4 RANDOM
Turns on/off the Random Play feature (see page 16).
5
Stops playback (see page 14).
6
Starts or pauses playback (see page 14).
■ FM/AM mode
Operations available in FM/AM mode
The following operations are available for the receiver.
y
Press FM/AM to set the receiver to the FM or AM mode before
carrying out the following operations.
1 PRESET /
Select a preset station (see page 18).
2 MEMORY
Stores a preset station in the memory (see page 18). Starts
Automatic preset tuning (see page 17).
3 TUNING /
Press TUNING / to Manual tuning and press
and hold TUNING / to Automatic tuning.
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
6
2
1
5
4
3
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
3
1
2
7 En
CONTROLS AND FUNCTIONS
English
INTRODUCTION
■ iPod mode
Operations available in iPod mode
The following operations are available for the iPod. For
details on iPod operations, see “Using iPod™” on
page 19.
y
Press iPod to set the receiver to the iPod mode before carrying out
the following operations.
1 REPEAT
Selects the Repeat Play mode (see page 19).
2 iPod MENU SEL
Press or to switch an item in the selected group.
3 ENTER
Press ENTER to enter the selected group. (Pressing
ENTER starts playback when a song is selected.)
4
Skips to the beginning of the current track. Press twice to
skip back to the previous track. Press and hold to fast
reverse.
5
Stops playback.
* The playback resumes from the first song in the iPod.
6 RANDOM
Turns on/off the Random Play feature (see page 19).
7 MENU
Returns to the upper level in the iPod menu.
8
Skips to the next song. Press and hold to fast forward.
9
Starts or pauses playback.
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
8
4
2
3
7
9
6
1
5
8 En
CONTROLS AND FUNCTIONS
■ Installing the batteries in the remote
control
1 Press the part and slide the battery
compartment cover off.
2 Insert two supplied batteries (AA, R6, UM-3)
according to the polarity markings (+ and –)
on the inside of the battery compartment.
3 Slide the cover back until it snaps into place.
■ Notes on batteries
• Change both batteries when the operation range of the
remote control decreases.
• Use AA, R6, UM-3 batteries.
• Make sure that the polarities are correct. See the
illustration inside the battery compartment.
• Remove the batteries if the remote control is not to be
used for an extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline
and manganese batteries) together. Read the packaging
carefully as these different types of batteries may have
the same shape and color.
• If the batteries have leaked, dispose of them
immediately. Avoid touching the leaked material or
letting it come into contact with clothing, etc. Clean the
battery compartment thoroughly before installing new
batteries.
• Do not throw away batteries with general house waste;
dispose of them correctly in accordance with your local
regulations.
■ Using the remote control
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the front panel of the system during
operation.
■ Handling the remote control
• The area between the remote control and the system
must be clear of large obstacles.
• Do not spill water or other liquids on the remote
control.
• Do not drop the remote control.
• Do not leave or store the remote control in the
following types of conditions:
– high humidity, such as near a bath
– high temperature, such as near a heater or a stove
– extremely low temperatures
– dusty places.
• Do not expose the remote control sensor to strong
lighting, in particular, an inverter type fluorescent
lamp; otherwise, the remote control may not work
properly. If necessary, position the system away from
direct lighting.
Press
ON
/
STANDBY
OFF
PHONES
VOLUME
INPUT PURE
DIRECT
TUNER PRESET
MIN MAX
USB
ON
/
STANDBY
OFF
30˚ 30˚
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
VOL
ENTER
TONE BALANCE
DISPLAY DIMMER SLEEP
RANDOM
REPEAT
MUTE
PURE DIRECT
TUNING
MEMORY
iPod MENU SEL
Within 6 m
(20 feet)
CONNECTING THE EXTERNAL COMPONENTS WITH THE SYSTEM
9 En
English
PREPARATION
Make sure you read the following procedure and notes carefully before connecting the system. For information on the
speakers (NS-BP400), refer to the owner’s manual supplied with it.
• Do not connect this unit or other components to the main power until all connections between components are complete.
• Do not let the bare speaker wires touch each other or do not them touch any metal part of the receiver. This could damage the receiver
and/or the speakers.
• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be
heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,
refer to the owner’s manual for each of your components.
Connecting the system
Connect the CD (L/R) jacks of the receiver to the OUTPUT (L/R) jacks of the CD player using the supplied audio
RCA stereo cable.
Connect the SYSTEM CONNECTOR (TO:CD PLAYER) jack of the receiver to the SYSTEM CONNECTOR
(TO:RECEIVER) jack of the CD player using the supplied system control cable.
Connect the speaker terminals (L) of the receiver to the speaker terminals of the left speaker and the speaker terminals (R)
of the receiver to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set (NS-
BP400). Also, attach the clamp filter to the speaker cables within 10 cm of the left and right speaker terminals (see page 2).
• The NS-BP400 speakers are not magnetically shielded, so place the speakers away from the monitor. When connecting speakers other
than NS-BP400, use the speakers having more than 6 Ω impedance.
• The PHONO jacks are only compatible with a turntable with MM cartridge.
• Connect your turntable to the GND terminal to reduce noise in the signal. However, you may hear less noise without the connection to
the GND terminal for some turntable(s).
When using banana plugs (commercially available), tighten the speaker terminals strongly then connect the banana plugs (for U.S.A,
Canada, Australia and China models).
CONNECTING THE EXTERNAL COMPONENTS WITH THE SYSTEM
CAUTION
R L
OUTPUT
SYSTEM
CONNECTOR
TO:RECEIVER
SPEAKERS:6 MIN.
R L
R
L
PHONO CD
GND
INPUT
SUB
WOOFER
OUTPUT
SYSTEM
CONNECTOR
TO:CD PLAYER
AUX
GND AM
75
UNBAL. FM
ANTENNA
RL RL
INPUT
INPUT
L
1
2
5
4
3
Receiver (R-1330)
CD player (CD-1330)
Left speaker
(NS-BP400)
Right speaker
(NS-BP400)
RCA stereo cable
(supplied)
System control
cable (supplied)
GND
Turntable DVD player etc. Subwoofer
Audio out
RCA
stereo
cable
Audio out
RCA
stereo
cable
Notes
CONNECTING ANTENNAS
10 En
To enjoy radio on this system, you need to connect FM/AM antennas to this unit. This product includes an indoor FM
antenna and AM loop antenna. If the radio wave reception is weak in your area or you want to improve the radio wave
reception, we recommend that you use outdoor antennas. For details, consult the nearest authorized Yamaha dealer or
service center.
Connect the supplied indoor FM antenna to the FM jack and AM loop antenna's GND terminal of the receiver. Place
the antenna away from the receiver and speaker cables. Find the best reception position, expand the antenna, then fix it.
Attach the antenna stand to the antenna. When attaching the antenna on the wall, you do not need to use the antenna
stand.
Connect the AM loop antenna lead wires to the AM and GND terminals of the receiver. There is no distinction
between the two lead wires for connecting. Twist the lead wires of the AM loop antenna and the indoor FM antenna
together before connecting to the GND terminal.
Place the AM loop antenna away from the system and speaker cables. While listening to the radio, rotate the antenna
head to find the best angle for reception.
■ Switching the voltage (Asia and Central/
South America models only)
The VOLTAGE SELECTOR on the rear panel of this system
must be set for your local voltage BEFORE plugging the power
cable into the AC wall outlet. Improper setting of the VOLTAGE
SELECTOR may cause damage to this system and create a
potential fire hazard.
Select the switch position (left or right)
according to your local voltage using a straight
slot screwdriver. Voltages are 220/230-240 V AC,
50/60 Hz.
■ Connecting the system to the wall outlet
After you made all connections, connect the power cables
of the system and other components.
CONNECTING ANTENNAS
R
L
PHONO CD
GND
INPUT
SUB
WOOFER
OUTPUT
SYSTEM
CONNECTOR
TO:CD PLAYER
AUX
GND AM
75
UNBAL. FM
ANTENNA
3
2
4
1
Indoor FM antenna
(supplied)
Ground
(GND terminal*)
AM loop antenna
(supplied)
* For the maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground.
A good earth ground is a metal stake driven into the moist earth.
Indoor FM antenna
AM loop antenna
CONNECTING THE POWER CABLES
SYSTEM
CONNECTOR
TO:RECEIVER
MAINS
H
ONO CD
SUB
WOOFER
OUTPUT
SYSTEM
CONNECTOR
TO:CD PLAYER
MAINS
AUX
GND AM
75
UNBAL. FM
ANTENNA
To AC wall outlet
To AC wall outlet
Asia and Central/
South America
models only
CAUTION
CONNECTING THE iPod™ AND THE USB DEVICE
11 En
English
PREPARATION
You can connect various audio components, USB device or iPod to the receiver. For information on your external
component, refer to the owner’s manual supplied with each component.
The receiver is equipped with a terminal on the top panel
where you can station your iPod and control playback of
your iPod using the supplied remote control.
Use this receiver with iPod dock adapter (supplied with
your iPod or commercially available) appropriate for your
iPod. If you use this receiver without using an appropriate
iPod dock adapter, loose connection may result.
y
When the receiver is turned on or in standby mode, connect the
iPod during the playback, the receiver automatically starts
playback of iPod .
• Only iPod (Click and Wheel), iPod nano, and iPod mini, and
iPod touch are supported.
• Do not connect any iPod accessories (such as headphones, a
wired remote control, or an FM transmitter) to your iPod when
it is stationed in a terminal.
• Unless your iPod is firmly stationed in a terminal, audio signals
may not be output properly.
• Once the connection between your iPod and the receiver is
complete and the receiver is set to iPod mode (see page 5),
“CONNECTED” appears in the front panel display. If the
connection between your iPod and the receiver fails, a status
message appears in the front panel display. For a complete list
of connection status message, see the iPod section in
“TROUBLESHOOTING” on page 20.
• When your iPod is stationed in a terminal of the receiver, your
iPod can be charged automatically even when the receiver is in
standby mode.
• You can disconnect the iPod during the playback.
This CD player has a USB port and can access MP3 or
WMA files saved on your USB device. Connect your USB
device to the USB port on the front panel of the CD
player.
Do not disconnect your USB device while the USB indicator is
blinking.
■ Supported USB devices
This CD player supports USB mass storage class devices
(e.g., flash memories, card readers or portable audio
players) using FAT16 or FAT32 format.
• Some devices may not work properly even if they meet the
requirements.
• Do not connect devices other than the USB mass storage class
devices.
• When you insert two or more memory cards at the same time
using card readers, etc., only one of the memory cards is
recognized.
• Yamaha and suppliers accepts no liability for the loss of data
saved on the USB devices connected to the receiver. As a
precaution, it is recommended that the files are made backup
copies.
• Playability of and power supply to all kind of USB devices are
not guaranteed.
• When your USB device is connected to the USB port, your
USB device can be charged automatically even when the CD
player is in standby mode and ECO mode is OFF
(see page 13).
• You can disconnect the USB device during the playback.
CONNECTING THE iPod™ AND THE USB DEVICE
Connecting an iPod™
Notes
ON
/
STANDBY
OFF
PHONES
VOLUME
INPUT
PURE
DIRECT
TUNER PRESET
MIN
MAX
iPod
Receiver
iPod
Connecting USB devices
CAUTION
Notes
USB
ON
/
STANDBY
OFF
CD player
USB device
SYSTEM OPERATIONS
12 En
Follow the procedure below to select an input source and adjust the sound settings on the system.
1 Press ON/STANDBY, OFF on the front panel
of the receiver and the CD player.
2 Press (standby/on) to turn on the
receiver.
Depending on the input mode of the receiver, the CD
player also turns on by the system control connection
(see page 9). The front panel display lights up.
3 Press one of the input selection keys (or
rotate INPUT on the front panel) to select the
desired input source.
4 Start playback on the selected source
component or select a radio station.
For information on the disc/USB device playback,
see page 14, and for information on tuning, see
page 17.
5 Press VOL +/– (or rotate VOLUME on the
front panel) to adjust the volume to the
desired output level.
■ To adjust the audio quality
1 Press TONE/BALANCE to select BASS,
TREBLE, or BALANCE.
2 To adjust the setting, press or .
BASS: Adjusts the low frequency response.
TREBLE: Adjusts the high frequency response.
BALANCE: Adjusts the volume level of each left
and right speaker channel.
■ Pure Direct mode
The Pure Direct mode shuts down the tone control
circuitry and front panel display, allowing you to enjoy
pure high-fidelity sounds.
Press PURE DIRECT (or PURE DIRECT on the
front panel) to turn on the Pure Direct mode.
The PURE DIRECT indicator lights up, and the front
panel display goes off.
• If you carry out operations while the Pure Direct mode is turned
on, the front panel display lights up briefly to acknowledge the
command.
• While the Pure Direct mode is turned on, neither BASS,
TREBLE, nor BALANCE is available.
To turn off the Pure Direct mode
Press PURE DIRECT again so that PURE DIRECT
indicator turns off and the front panel display lights up.
■ Muting the sound (MUTE)
Press MUTE to turn off the sound.
MUTE ON appears on the front panel display.
To restore the sound, press MUTE again or press VOL +/–.
SYSTEM OPERATIONS
Basic system operations
ON
/
STANDBY
OFF
PHONES
VOLUME
INPUT PURE
DIRECT
TUNER PRESET
MIN MAX
USB
ON
/
STANDBY
OFF
VOL
VOL
TONE BALANCE
DISPLAY DIMMER SLEEP
MUTE
PURE DIRECT
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
TUNING
(standby/on)
VOL +/–
INPUT
Input selection
keys
ON/STANDBY, OFF
VOLUME
PURE DIRECT
TONE/BALANCE
/
PURE DIRECT
MUTE
Notes
SYSTEM OPERATIONS
13 En
English
BASIC
OPERATIONS
■ To use the ECO mode of the CD player
This mode reduces the power consumption during the
standby mode. Even if the USB device is connected to the
USB port of the CD player, the USB device cannot be
charged when the CD player is in standby mode and ECO
mode is ON.
Press ON/STANDBY, OFF while pressing and
holding of the CD player to turn on the CD
player.
Each time you turn on the CD player by press
ON/STANDBY, OFF while pressing and holding of
the CD player, ECO ON or ECO OFF appears on the front
panel display alternately.
Follow the procedure below to change the brightness of
the receiver’s and CD player’s front panel display.
Press DIMMER.
You can choose your desired brightness of the front panel
display between normal (bright), mid dim, and dim.
The sleep timer sets the system to the standby mode after
the specified time elapses.
Press SLEEP repeatedly to select the desired
duration.
Each time you press the key, the duration changes as
follows.
The SLEEP indicator lights up in the front panel display.
y
• The sleep timer is canceled if you set the receiver to the standby
mode.
• If you press SLEEP while the sleep timer is set, the remaining
time appears in the front panel display.
To cancel the sleep timer
Press SLEEP repeatedly to select “OFF”.
You can connect your headphones to the PHONES jack
on the front panel of the receiver.
The sound from the speakers and the subwoofer stops.
Changing the brightness of the
front panel display
Setting the sleep timer
VOL
TONE BALANCE
DISPLAY DIMMER SLEEP
MUTE
PURE DIRECT
DIMMER
VOL
TONE BALANCE
DISPLAY DIMMER SLEEP
MUTE
PURE DIRECT
SLEEP
To use headphones
120min.
90min.
60min.
30min.
OFF
ON
/
STANDBY
OFF
PHONES
DISC AND USB DEVICE OPERATIONS
14 En
You can enjoy playing back your audio CDs, USB devices, and MP3 or WMA files recorded on a disc/USB device.
Some operations may be different or restricted depending on the disc/USB device. Before playing back, check the
compatibility of your disc/USB device with this system (see page 23).
Depending on the disc, some operations may be different or
restricted.
■ To start disc playback
1 Select CD as an input source (see page 12).
2 Press to open the disc tray and load a
CD.
3 Press .
Playback starts automatically.
For an audio CD, playback starts from the first track,
and for MP3 or WMA files, playback starts in
alphanumeric order by the filename.
y
You can also close the disc tray by pressing on the front
panel of the CD player.
■ To start USB device playback
1 Select USB as an input source (see page 12).
2 Connect your USB device to the USB port on
the CD player.
The total number of files is displayed.
The reading time may exceed 30 seconds depending
on the number of files/folders.
3 Press to start playback.
For a USB device, playback in order by the date and
time of creation if playable files are in the USB
device.
• Total time does not appear for USB device playback.
• If the USB device is partitioned, only the first partition is
displayed.
• Some files may not work properly depending on the USB
device specification.
• Copyright-protected files cannot be played back.
• This system can play back files of 4 GB in size or less.
To stop playback
Press .
For audio CD, the total track number and total time of the
disc are displayed and for MP3/WMA disc or USB device,
the total file number is displayed on the front panel.
To pause playback
Press .
To return to normal playback, press .
To skip tracks
• To skip to the start of the current track, press .
• To skip to the next track, press .
• To skip to the previous track, quickly press twice.
To fast reverse or fast forward
• To fast reverse, press and hold .
• To fast forward, press and hold .
y
The sound can be heard (although slightly garbled) during these
operation in either direction. This is convenient for locating a
precise position within a track, or for reviewing the contents
quickly. Sound may not be heard depending on the MP3/WMA
file.
DISC AND USB DEVICE OPERATIONS
Note
Playback operations
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
MENU
VOL
ENTER
RANDOM
REPEAT
TUNING
MEMORY
iPod MENU SEL
/
USB
CD
Notes
DISC AND USB DEVICE OPERATIONS
15 En
English
BASIC
OPERATIONS
You can switch the disc playback information shown in the CD player’s front panel display. Available information
differs depending on the type of the disc/USB device.
Press DISPLAY repeatedly while playing back a
disc/USB device.
Each time you press the key, the information display
changes as described in “Playback information for audio
CDs” and “Playback information for MP3 or WMA files
recorded on discs/USB devices”.
Some special characters may not be shown properly.
■ Playback information for audio CDs
The following information is available during playback of an audio CD.
■ Playback information for MP3 or WMA files recorded on discs/USB devices
Switching the playback information display
VOL
TONE BALANCE
DISPLAY DIMMER SLEEP
MUTE
PURE DIRECT
DISPLAY
Note
1 Elapsed time of the current track
2 Remaining time of the disc
2 File name
1 Elapsed time of the current file
Returns to the normal display after displaying a file name.
DISC AND USB DEVICE OPERATIONS
16 En
You can repeat the playback of the selected item in a disc/
USB.
1 Play back the disc/USB you want to repeat.
2 During the playback of the disc/USB, press
REPEAT to select the desired Repeat Play
mode.
Each time you press the key, the Repeat Play mode
indicator in the CD player’s front panel display
changes as follows.
To cancel Repeat Play
Press REPEAT repeatedly so that the Repeat Play mode
indicator disappears from the front panel display.
The Repeat Play mode is canceled when the disc/USB device is
removed.
y
REP OFF appears when the system is set to the Pure Direct
mode.
You can play back tracks in the disc/USB in random
order.
When playing back with Random Play, the remaining time of the
disc cannot be displayed.
Press RANDOM while playback is stopped.
The RANDOM indicator lights up in the CD player’s
front panel display and Random Play starts.
To cancel Random Play
Press .
Repeating playback
(Repeat Play)
Note
REPEAT
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
RANDOM
REPEAT
TUNING
MEMORY
iPod MENU SEL
Off (Normal playback)
REP S (Repeat Play by the current track)
REP ALL (Repeat Play by disc/USB)
Playing back randomly
(Random Play)
Note
CDiPod
FM/AM
PHONO
AUX
USB
PRESET
RANDOM
REPEAT
TUNING
MEMORY
iPod MENU SEL
RANDOM
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
Sayfa yükleniyor ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
