Philips GC8215/01 Kullanım kılavuzu

GC8215

2

3

A B C D E

F

G

H

I

J

MNOP

L

K

1

4

GC8215

ENGLISH 6

DANSK 16

DEUTSCH 26

 36

ESPAÑOL 47

SUOMI

57

FRANÇAIS 67

ITALIANO

77

NEDERLANDS

87

NORSK

97

PORTUGUÊS

107

SVENSKA

117

TÜRKÇE 127

6

Introduction

Congratulations on your purchase and welcome to Philips! To fully benet

from the support that Philips offers, register your product at www.philips.

com/welcome.

This powerful pressurised ironing system produces non-stop steam to

make ironing easier. Thanks to the large water tank, you can iron without

interruption. When the water tank is empty, you can detach it and rell it

immediately.

We hope you enjoy using this ironing system.

General description (Fig. 1)

A Supply hose

B Temperature dial

C Temperature light

D Steam lock

E Steam activator

F Soleplate

G Iron stand

H Detachable water tank

I Cord & hose storage hook

J Calc-Clean rinsing cap

K Filling opening

L Water tank release lever

M Steam generator

N Transport handgrip

O Mains cord

P On/off switch with power-on light

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Danger

Never immerse the iron or the steam generator in water.

Warning

Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

Do not use the appliance if the plug, the mains cord, the supply hose or

the appliance itself shows visible damage, or if the appliance has been

dropped or leaks.

If the mains cord or the supply hose is damaged, you must have it

replaced by Philips, a service centre authorised by Philips or similarly

qualied persons in order to avoid a hazard.

Never leave the appliance unattended when it is connected to the

mains.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for

their safety.

-

ENGLISH

Children should be supervised to ensure that they do not play with the

appliance.

Do not let the mains cord and supply hose come into contact with the

hot soleplate of the iron.

If steam escapes from under the Calc-Clean rinsing cap when the

appliance heats up, switch off the appliance and tighten the Calc-Clean

rinsing cap. If steam continues to escape when the appliance heats up,

switch off the appliance and contact a service centre authorised by

Philips.

Never remove the Calc-Clean rinsing cap when the steam generator

is hot.

Do not use any other cap on the steam generator than the Calc-Clean

rinsing cap that has been supplied with the appliance, as this cap also

functions as a safety valve.

Caution

Only connect the appliance to an earthed wall socket.

Check the mains cord and the supply hose regularly for possible

damage.

Always place and use the iron and the steam generator on a stable,

level and horizontal surface.

The soleplate of the iron can become extremely hot and may cause

burns if touched.

When you have nished ironing, when you clean the appliance, when

you ll or empty the water tank and also when you leave the appliance

even for a short while: put the iron on the iron stand, switch off the

appliance and remove the mains plug from the wall socket.

Rinse the steam generator regularly according to the instructions in the

chapter ‘Cleaning and maintenance’.

This appliance is intended for household use only.



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.



Note: The iron may give off some smoke when you use it for the rst time. This

is normal and stops after a short while.

Note: Some particles may come out of the soleplate when you use the iron for

the rst time. This is normal; the particles are harmless and stop coming out of

the iron after a short while.

Note: When you switch on the appliance, the steam generator may produce a

pumping sound. This is normal; the sound tells you that water is pumped into

the steam generator.

1 Remove any sticker or protective foil from the soleplate and clean

the soleplate with a soft cloth.

-

ENGLISH 7

Preparing for use

1

Place the steam generator on a stable and level surface, e.g. on the

hard part of the ironing board or on a table.

Filling the detachable water tank

You can rell the water tank at any time during ironing.

Do not put hot water, perfume, vinegar, starch, descaling agents, ironing

aids or other chemicals in the water tank.

Do not overll the water tank, otherwise water may spill out of the

lling opening when you reinsert the water tank.

1 Remove the detachable water tank from the steam generator.

2 Fill the water tank with tap water up to the MAX indication.

Note: If the tap water in your area is very hard, we advise you to mix it with an

equal amount of distilled water.

3 Slide the water tank back into the steam generator (‘click’).

Note: If the water tank is not properly placed, the iron does not produce any

steam.

Setting the temperature

1 Check the laundry care label of the article to be ironed to

determine the required ironing temperature

1 for synthetic fabrics ( e.g. acrylic, viscose, polyamide) and silk

2 for wool

3 for cotton

MAX for linen

2 To set the required ironing temperature, turn the temperature dial

to the appropriate position.

3 Put the mains plug in an earthed wall socket and set the on/off

switch to ‘on’.

The power-on light in the on/off switch goes on.

The temperature light on the iron goes on.

When the iron has reached the set temperature, the temperature

light goes out.

Note: During ironing, the temperature light goes on from time to time. This

indicates that the iron is heating up to the set temperature.

-

,

L

I

N

E

N

L

I

N

C

O

T

O

N

C

O

T

O

N

W

O

L

A

I

N

E

S

I

L

K

S

O

I

E

N

Y

L

O

N

Y

L

O

N

M

A

X

M

I

N

L

I

N

E

N

L

I

N

C

O

T

O

N

C

O

T

O

N

W

O

L

A

I

N

E

S

I

L

K

S

O

I

E

N

Y

L

O

N

Y

L

O

N

M

A

X

M

I

N

OnOn

ENGLISH8

Tips

If you do not know what kind or kinds of fabric an article is made of,

determine the right ironing temperature by ironing a part that is not

visible when you wear or use the article.

If the fabric consists of various kinds of bres, always select the

temperature required by the most delicate bre, i.e. the lowest

temperature. For example: if a fabric consists of 60% polyester and 40%

cotton, it must be ironed at the temperature indicated for polyester

(1) and without steam.

Start ironing the articles that require the lowest ironing temperature,

i.e. those made of synthetic materials.

If you set a lower temperature during ironing, wait until the iron has

cooled down to the set temperature before you continue ironing. To

make the iron cool down faster, simply press the steam activator or

iron a piece of cloth.

Using the appliance

Steam ironing

The supply hose may become hot during a long ironing session.

Note: The system may occasionally produce a pumping sound during steam

ironing. This is normal and tells you that water is being pumped into the steam

generator.

1 Make sure there is enough water in the water tank.

2 Make sure the appliance is plugged in and switched on.

3 Set the required ironing temperature (see chapter ‘Preparing for

use’).

Steam ironing is only possible at ironing temperatures higher than 2.

When the iron has reached the set temperature, the temperature

light goes out.

After approx. 2 minutes, the steam generator is ready for steam

ironing.

4 Press the steam activator to start steam ironing.

When you put down the iron during ironing, put it on its heel or on the

iron stand.

The opening and closing of the steam valve in the steam generator

causes a clicking sound. This is normal.

Steam lock function

The steam lock allows you to steam iron non-stop without having to press

the steam activator continuously.

To let the iron produce steam continuously, slide the steam lock

backwards while you press the steam activator.

-

,

-

ENGLISH 9

To make the iron stop producing steam continuously, slide the steam

lock forwards. When the steam lock is in this position, the iron only

produces steam when the steam activator is pressed.

Note: Release the steam lock when you put the iron on its heel or on the iron

stand. This prevents that hot steam escapes from the iron or that the iron

stand gets wet.

Vertical steaming

Never direct the steam at people.

1 Hold the iron in vertical position and press the steam activator to

steam iron hanging curtains and clothes (jackets, suits, coats).

Ironing without steam

1 To iron without steam, simply start ironing without pressing the

steam activator.

Tips

When you steam iron woollen fabrics, shiny patches may occur. To

prevent this, use a dry pressing cloth or turn the article inside out and

iron the reverse side.

Silk, woollen and synthetic materials: iron the reverse side of the fabric

to prevent shiny patches.

Iron velvet and other fabrics that tend to acquire shiny patches in one

direction only (along with the nap) while you apply very little pressure.

Do not use steam when you iron coloured silk. This could cause stains.

Cleaning and maintenance

After ironing

1 Put the iron on the iron stand and switch off the appliance.

2 Remove the mains plug from the wall socket and let the appliance

cool down.

3 Wipe scale and any other deposits off the soleplate with a damp

cloth and a non-abrasive (liquid) cleaner.

4 Clean the upper part of the iron and the outside of the steam

generator with a moist cloth.

5 Empty the water tank after cleaning.

-

OffOff

ENGLISH10

Calc-Clean function

Never remove the Calc-Clean rinsing cap when the steam generator is

hot.

VERY IMPORTANT: Rinse the steam generator once a month or after

every 10 times of use, to prevent damage to the appliance and for

optimal steaming performance.

1 Unplug the appliance and let it cool down for 2 hours.

2 Remove the detachable water tank.

3 Hold the steam generator with both hands and shake well.

4 Turn the steam generator on its side with the Calc-Clean rinsing cap

facing upwards, and remove the Calc-Clean rinsing cap.

5 Empty the steam generator into the sink.

6 Fill the steam generator with fresh water and shake again.

ENGLISH 11

7 Empty the steam generator into the sink again.

8 Repeat steps 6 & 7 twice to obtain the best result.

9 Screw the Calc-Clean rinsing cap tightly back onto the steam

generator.

Storage

Always let the appliance cool down before you store it.

1 Empty the water tank.

2 Pull out the cord & hose storage hook.

3 Secure the supply hose and mains cord.

4 To move the appliance, carry it by the handgrips on either side of the

steam generator.

ENGLISH12

Environment

Do not throw away the appliance with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this, you help to preserve the environment.

Guarantee & service

If you need service or information or if you have a problem, please visit

the Philips website at www.philips.com or contact the Philips Consumer

Care Centre in your country (you nd its phone number in the worldwide

guarantee leaet). If there is no Consumer Care Centre in your country, go

to your local Philips dealer.

Troubleshooting

This chapter summarises the most common problems you could

encounter with the appliance. If you are unable to solve the problem with

the information below, contact the Consumer Care Centre in your country.

Problem Cause Solution

The appliance does

not become hot.

There is a connection problem. Check the mains cord, the plug

and the wall socket.

You have not switched on the appliance. Set the on/off switch to ‘on’.

The set temperature is too low. Set a higher temperature.

Smoke comes out of

my new iron when I

switch it on.

Some parts of the appliance have been

lightly greased in the factory and may

initially give off some smoke when heated.

This phenomenon is normal and

ceases after a short while.

The iron does not

produce any steam.

There is not enough water in the water

tank.

Fill the water tank. See

chapter ‘Preparing for use’, section

‘Filling the detachable water tank’.

The steam generator has not heated up

sufciently.

Wait approx. 2 minutes.

The set ironing temperature is too low for

steam ironing.

Set a temperature of 2 or

higher.

You have not placed the water tank

properly in the steam generator.

Place the water tank properly in

the steam generator (‘click’).

When the iron is set to a very high

temperature, the steam produced is dry

and hardly visible. It is even less visible

when the ambient temperature is relatively

high and it is entirely invisible when the

temperature has been set to MAX.

Set the iron to a lower

temperature, e.g. 2, to check if

the iron actually produces steam.

-

ENGLISH 13

Problem Cause Solution

Water droplets

come out of the

soleplate.

The set temperature is too low for steam

ironing.

Set a temperature of 2 or

higher.

When you start steam ironing and when

you stop steam ironing for a while, the

steam still present in the supply hose

cools down and condenses into water. This

causes water droplets to come out of the

soleplate.

This is normal. When you start

ironing or when you continue

ironing after an interruption, hold

the iron over an old cloth and

press the steam activator. Wait

until steam instead of water

comes out of the soleplate.

Flakes and impurities

come out of the

soleplate or the

soleplate is dirty.

Impurities or chemicals present in the water

have deposited in the steam vents and/or

on the soleplate.

Clean the soleplate with a damp

cloth.

The appliance

produces a pumping

sound.

Water is pumped into the steam generator. This is normal.

The pumping sound does not stop. Unplug the iron immediately and

contact an authorised Philips

service centre.

The iron produces

steam continuously.

You have slid the steam lock backwards

while pressing the steam activator.

Slide the steam lock forwards

to unlock the steam lock (see

section ‘Steam lock function’).

Dirty water comes

out of the soleplate.

Too much scale and minerals have

accumulated inside the steam generator.

Rinse the steam generator.

See chapter ‘Cleaning and

maintenance’.

Steam escapes from

under the Calc-

Clean rinsing cap

when the appliance

heats up.

You have not tightened the Calc-clean

rinsing cap properly.

Switch off the appliance, tighten

the Calc-Clean rinsing cap and

switch on the appliance again. If

steam continues to escape when

the appliance is heating up, switch

off the appliance and contact

a service centre authorised by

Philips.

The iron does not

produce enough

steam/the amount

of steam decreases

and increases during

steam ironing.

When the appliance pumps water into

the steam generator, the steam amount

sometimes decreases. This is probably

when you think that the iron does not

produce enough steam. However this is a

normal phenomenon and the steam output

normalises within a few seconds.

To optimise the steam output,

release the steam lock when you

do not need steam and when you

put down the iron.

ENGLISH14

Problem Cause Solution

Wet spots appear

on the fabric during

ironing.

The wet spots that appear on the fabric

after you have steam ironed for some

time may be caused by steam that has

condensed onto the ironing board. Iron the

wet spots without steam for some time to

dry them. If the underside of the ironing

board is wet, wipe it with a piece of dry

cloth.

To prevent steam from condensing

onto the ironing board, use an

ironing board with a wire mesh

top.

ENGLISH 15

16

Introduktion

Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte af

den støtte, Philips tilbyder, skal du registrere dit produkt på www.philips.

com/welcome.

Dette kraftfulde strygesystem med tryk producerer konstant damp, hvilket

gør strygningen lettere. Takket være den store vandtank kan du stryge uden

afbrydelse. Når vandtanken er tom, tages den blot af og fyldes igen.

Vi håber, at du vil få glæde af dette strygesystem



A Dampslange

B Temperaturvælger

C Temperaturindikator med lys

D Damplås

E Dampaktiveringsknap

F Strygesål

G Holder til strygejernet

H Aftagelig vandtank

I Krog til opbevaring af ledning og slange

J Calc-Clean-dæksel

K Påfyldningsåbning

L Udløser til vandtank

M Damptank

N Transporthåndtag

O Netledning

P On/off-kontakt med lys

Vigtigt

Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i

brug, og gem den til eventuelt senere brug.

Fare

Hverken strygejern eller damptank må kommes ned i vand.

Advarsel

Kontrollér, om spændingsangivelsen på typeskiltet svarer til den lokale

netspænding, før du tilslutter apparatet.

Brug ikke apparatet, hvis stik, netledning, dampslange eller selve

apparatet viser tegn på beskadigelse, eller hvis apparatet er blevet tabt,

eller det er utæt.

Hvis ledningen eller dampslangen beskadiges, må de kun udskiftes af

Philips, et autoriseret Philips-serviceværksted eller af en kvaliceret

fagmand for at undgå enhver risiko ved efterfølgende brug.

Hold altid apparatet under opsyn, når det er sluttet til lysnettet.

Dette apparat er ikke beregnet til at blive brugt af personer (herunder

børn) med nedsatte fysiske og mentale evner, nedsat følesans eller

manglende erfaring og viden, medmindre de er blevet vejledt eller

instrueret i apparatets anvendelse af en person, der er ansvarlig for

deres sikkerhed.

Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke

kan komme til at lege med det.

-

DANSK

Lad ikke netledningen og dampslangen komme i kontakt med den

varme strygesål på strygejernet.

Hvis der slipper damp ud af Calc-Clean-dækslet, mens

apparatet varmer op, skal du slukke for apparatet og stramme Calc-

Clean dækslet. Slipper der fortsat damp ud under opvarmningen,

skal du slukke for apparatet og kontakte et autoriseret Philips-

serviceværksted.

Calc-Clean-dækslet må aldrig fjernes, når dampgeneratoren er varm.

Brug ikke andre låg til dampgeneratoren end det medfølgende Calc-

Clean-dæksel, da dette samtidig fungerer som sikkerhedsventil.

Forsigtig

Apparatet må kun sluttes til en stikkontakt med jordforbindelse.

Kontrollér med jævne mellemrum, at netledningen og dampslangen er

hel og ubeskadiget.

Placér og brug altid strygejern og dampgenerator på et stabilt, plant og

vandret underlag.

Strygesålen kan blive utrolig varm og forårsage brandsår ved berøring.

Når du er færdig med at stryge, når du rengør apparatet, når du fylder

eller tømmer vandtanken, og når du forlader apparatet – selv om det

kun er i et kort øjeblik – skal du placere strygejernet i holderen, slukke

for apparatet og tage stikket ud af stikkontakten.

Rengør damptanken regelmæssigt ifølge anvisningerne i afsnittet

“Rengøring og vedligeholdelse”.

Dette apparat er kun beregnet til almindelig husholdningsbrug.

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle standarder for elektromagnetiske

felter (EMF). Ved korrekt anvendelse i overensstemmelse med

instruktionerne i denne brugsvejleding, er apparatet sikkert at anvende,

ifølge den videnskabelige viden, der er tilgængelig i dag.

Før apparatet tages i brug første gang

Bemærk: Der kan komme lidt røg fra strygejernet, når det tændes første gang.

Dette er helt normalt og forsvinder hurtigt.

Bemærk: Når strygejernet bruges første gang, kan der drysse lidt partikler ud

fra strygesålen. Det er helt normalt. Partiklerne er uskadelige og forsvinder

efter et kort øjeblik.

Bemærk: Når apparatet tændes, høres der måske en pumpelyd fra

dampgeneratoren. Det er helt normalt. Lyden indikerer, at der pumpes vand ind

i dampgeneratoren.

1 Fjern eventuelle mærkater eller beskyttelseslm fra strygesålen, og

rengør den med en blød klud.

-

DANSK 17

Klargøring

1

Placér dampgeneratoren på et stabilt, jævnt underlag, f.eks. på den

hårde del af strygebrættet eller et bord.

Påfyldning af den aftagelige vandtank

Vandtanken kan påfyldes når som helst under strygningen.

Kom aldrig varmt vand, parfume, eddike, stivelse, afkalkningsmiddel,

strygemiddel eller andre kemikalier i vandtanken.

Overfyld ikke vandtanken, da der kan løbe vand ud af

påfyldningsåbningen, når du sætter vandtanken tilbage.

1 Tag den aftagelige vandtank af dampgeneratoren.

2 Fyld vandtanken med vand fra vandhanen op til MAX-markeringen.

Bemærk: Er vandet i dit område meget hårdt, anbefales det at anvende lige

dele postevand og lige dele destilleret vand.

3 Sæt vandtanken tilbage på dampgeneratoren (“klik”).

Bemærk: Hvis vandtanken ikke er isat korrekt, kan strygejernet ikke producere

damp.

Temperaturindstilling

1 Kontrollér vaskemærket på det tøj/stof, der skal stryges, for at nde

den rette strygetemperatur

1 til syntetiske materialer (f.eks. akryl, viskose, polyamid) og silke

2 til uld

3 til bomuld

MAX til linned

2 Indstil den ønskede strygetemperatur ved at dreje

temperaturvælgeren.

3 Sæt stikket i en jordet stikkontakt, og sæt on/off-kontakten på “on”.

Lyset i on/off-kontakten tændes.

Temperaturindikatoren på strygejernet tændes.

Når strygejernet har nået den indstillede temperatur, slukker

temperaturindikatoren.

Bemærk: Under strygning tændes og slukkes temperaturindikatoren fra tid

til anden. Dette indikerer blot, at strygejernet opvarmes til den indstillede

temperatur.

-

,

L

I

N

E

N

L

I

N

C

O

T

O

N

C

O

T

O

N

W

O

L

A

I

N

E

S

I

L

K

S

O

I

E

N

Y

L

O

N

Y

L

O

N

M

A

X

M

I

N

L

I

N

E

N

L

I

N

C

O

T

O

N

C

O

T

O

N

W

O

L

A

I

N

E

S

I

L

K

S

O

I

E

N

Y

L

O

N

Y

L

O

N

M

A

X

M

I

N

OnOn

DANSK18

Gode råd

Er du i tvivl om, hvilket materiale et stykke tøj er fremstillet af, må du

nde den rette strygetemperatur ved at prøve dig frem et sted, som

ikke er synligt, når du har tøjet på.

Hvis stoffet er fremstillet af ere slags bre, skal du altid vælge den

temperatur, som passer til den mest sarte bertype, dvs. den laveste

temperatur. Hvis et stykke tøj f.eks. består af 60 % polyester og 40 %

bomuld, skal det stryges ved den temperatur, som passer til polyester

(1), og uden damp.

Stryg først det tøj, der kræver den laveste temperatur, f.eks. syntetiske

materialer.

Hvis du indstiller en lavere temperatur under strygningen, skal du vente,

indtil strygejernet er kølet ned til den indstillede temperatur, før du

fortsætter med at stryge. For at få strygejernet til at køle hurtigere af

kan du trykke på dampaktiveringsknappen eller stryge på et stykke stof.

Sådan bruges apparatet

Dampstrygning

Dampslangen kan blive varm under en længere strygeperiode.

Bemærk: Under dampstrygning høres en pumpelyd fra tid til anden. Dette er

helt normalt og betyder blot, at der pumpes vand ind i dampgeneratoren.

1 Sørg for, at der er tilstrækkeligt med vand i vandtanken.

2 Sørg for at apparatet er sat i stikkontakten, og at der er tændt.

3 Indstil den ønskede strygetemperatur (se afsnittet “Klargøring”).

Dampstrygning er kun mulig ved strygetemperaturer, der er højere end

2.

Når strygejernet har nået den indstillede temperatur, slukker

temperaturindikatoren.

Efter ca. 2 minutter er dampgeneratoren klar til dampstrygning.

4 Tryk på dampaktiveringsknappen for at begynde dampstrygning.

Når du stiller strygejernet fra dig, skal det enten stilles på højkant eller i

holderen.

Når dampventilen i dampgeneratoren åbnes og lukkes, høres en

klikkende lyd. Det er helt normalt.

Damplåsfunktion

Damplåsen gør det muligt for dig at dampstryge uden hele tiden at skulle

trykke på dampaktiveringsknappen.

Skub damplåsen bagud, mens du holder dampaktiveringsknappen nede

for at få strygejernet til at producere konstant damp.

-

,

-

DANSK 19

For at få strygejernet til at holde op med at producere konstant

damp skal du skubbe damplåsen frem. Når damplåsen står i denne

position, producerer strygejernet kun damp, når der trykkes på

dampaktiveringsknappen.

Bemærk: Slip damplåsen, når du stiller strygejernet på hælen eller i holderen.

Det forhindrer, at der slipper varm damp ud fra strygejernet, eller at holderen

til strygejernet bliver våd.

Lodret damp

Ret aldrig dampstrålen mod personer.

1 Hold strygejernet i lodret stilling, og tryk på dampaktiveringsknappen

for at dampstryge gardiner og tøj (jakker, jakkesæt og frakker), der er

hængt op.

Tørstrygning (uden damp)

1 Du kan stryge uden damp ved at undlade at trykke på

dampaktiveringsknappen.

Gode råd

Når du stryger uldstoffer, kan der opstå blanke skjolder. For at undgå

dette skal du bruge en tør klud til at lægge imellem eller vende vrangen

ud på tøjet og stryge det på bagsiden.

Silke, uld eller kunststof: Stryg tøjet på vrangen for at undgå blanke

skjolder.

Fløjl og andre stoffer, som har tendens til at få blanke skjolder, bør kun

stryges i én retning (med luven) og kun med et let tryk.

Undlad at bruge damp ved strygning af indfarvede silkestoffer, da det

kan give skjolder på tøjet.

Rengøring og vedligeholdelse

Efter brug

1 Placér strygejernet i holderen , og sluk for apparatet.

2 Tag stikket ud af stikkontakten, og lad apparatet køle af.

3 Tør strygesålen af med en fugtig klud med lidt ikke-ridsende

(ydende) rengøringsmiddel.

4 Tør strygejernets overdel og ydersiden af dampgeneratoren af med

en fugtig klud.

5 Tøm vandtanken efter rengøring.

-

OffOff

DANSK20

Sayfa yükleniyor ...

Philips GC8215/01 Kullanım kılavuzu

Philips GC8215/01 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler