Philips GC8280 El kitabı

8000 series

GC8280

2

3

MAX

E

F

A

CB

D

H

I

J

L

K

M

V

U

T

Q

N O

S

R

P

G

1

2

4

GC8280

ENGLISH 6

DANSK 19

DEUTSCH 32

 46

ESPAÑOL 61

SUOMI

75

FRANÇAIS 88

ITALIANO 102

NEDERLANDS

116

NORSK 130

PORTUGUÊS 143

SVENSKA

157

TÜRKÇE

170

6

Introduction

Thank you for buying the Philips GC8280. Please read these instructions for

use, as they contain information about the surprising features of this ironing

system and some tips to make ironing easier and more enjoyable.

The Philips GC8280 is a powerful pressurised ironing system that produces

non-stop steam to make ironing easier. Thanks to the large water tank

you can iron without interruption. When the water tank is empty you can

detach it and rell it immediately.

The Philips GC8280 is equipped with a sophisticated display that gives you

more control over the ironing process. It gives feedback on the selected

temperature setting and has precise pre-programmed temperature settings

for 12 different fabrics. It also informs you about the steam setting and the

water level and warns you when the iron needs to be rinsed. The iron is

very safe thanks to the automatic iron-off function. Last but not least, it is

the only ironing system on the market with an integrated drip stop.

We hope you will enjoy using the Philips GC8280.

General description (Fig. 1)

A Supply hose

B Handle with soft grip

C Steam activator

D Display

E Temperature buttons (+/-)

F Menu button

G Soleplate

H Safe storage lock

I Iron stand

J Detachable water tank

K Filling cup

L Cord & hose storage hook

M Calc-Clean rinsing cap

N Filling opening

O Water tank release lever

P Steam tank

Q On/off button with power-on light

R Transport handgrip

S Water tank rell light

T Mains cord

U Steam buttons (+/-)

V Steam tank control panel with steam light

p = maximum steam

[ = moderate steam

] = minimum steam

a = no steam

Important

Read this user manual carefully before you use the appliance and save it for

future reference.

Check if the voltage indicated on the type plate corresponds to the

local mains voltage before you connect the appliance.

Only connect the appliance to an earthed wall socket.

-

,

ENGLISH

Do not use the appliance if the plug, the cord, the supply hose or

the appliance itself shows visible damage, or if the appliance has been

dropped or is leaking.

Check the cord and the supply hose regularly for possible damage.

If the mains cord or the supply hose is damaged, it must be replaced

by Philips, a service centre authorised by Philips or similarly qualied

persons in order to avoid a hazard.

Never leave the appliance unattended when it is connected to the

mains.

Never immerse the iron or the steam tank in water.

This appliance is not intended for use by persons (including children)

with reduced physical, sensory or mental capabilities, or lack of

experience and knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that they do not play with

the appliance.

The soleplate of the iron can become extremely hot and may cause

burns if touched.

Do not allow the mains cord and supply hose to come into contact

with the soleplate when it is hot.

When you have nished ironing, when you clean the appliance, when

you ll or empty the water tank and also when you leave the iron

even for a short while: put the iron on the stand, switch the appliance

off and remove the mains plug from the wall socket.

Always place and use the iron and the steam tank on a stable, level

and horizontal surface. Do not put the steam tank on the soft part of

the ironing board.

If steam escapes from under the Calc-Clean rinsing cap when the

appliance is heating up, switch the appliance off and tighten the Calc-

Clean rinsing cap. If steam continues to escape when the appliance

is heating up, switch the appliance off and contact a service centre

authorised by Philips.

Do not use any other cap on the steam tank than the cap that has

been supplied with the appliance, as this cap also functions as a safety

valve.

Rinse the steam tank regularly according to the instructions in the

chapter ‘Cleaning’.

Never remove the Calc-Clean rinsing cap when the steam tank is

hot.

This appliance is intended for household use only.



This Philips appliance complies with all standards regarding electromagnetic

elds (EMF). If handled properly and according to the instructions in this

user manual, the appliance is safe to use based on scientic evidence

available today.



Note: The iron may give off some smoke when you use it for the rst time. This

is normal and will stop after a short while.

,

ENGLISH 7

Note: Some particles may come out of the soleplate when you use the iron for

the rst time. This is normal; the particles are harmless and will stop coming

out of the iron after a short while.

Note: When you switch the appliance on, the steam tank may produce a

pumping sound. This is normal; the sound tells you that water is being pumped

into the steam tank.

1 Remove any sticker or protective foil from the soleplate and clean

the soleplate with a soft cloth.

2 Check the hardness of the tap water with the test strip supplied.

y = soft water

u = moderately hard water

i = hard water

o = very hard water

Preparing for use

1

Place the steam tank on a stable and level surface, i.e. on the hard

part of the ironing board or on a table.

Filling the detachable water tank

The water tank can be relled at any time during use.

Do not put hot water, perfume, vinegar, starch, descaling agents, ironing

aids or other chemicals in the water tank.

Do not overll the water tank, otherwise water may spill out of the

lling opening when you reinsert the water tank.

1 Remove the detachable water tank from the steam tank.

If the tap water in your area is very hard, we advise you to mix it with an

equal amount of distilled water.

2 Fill the water tank up to the MAX indication.

3 Slide the water tank back into the steam tank (‘click’).

If the water tank is not properly placed, the iron does not produce any

steam.



When the water tank is almost empty, the message ‘WATER LOW,

REFILL WATER TANK’ is shown on the display and you will hear two

short beeps.

The water tank rell light starts blinking and steam ironing is no

longer possible.

Rell the water tank. The iron starts steaming again as soon as the

water tank has been properly reinserted into the steam tank.

,

ENGLISH8

Setting the temperature

1 Put the mains plug in an earthed wall socket and press the on/off

button once.

The power-on light goes on.

The display lights up and you will hear a short beep. The following

message moves across the display:

’WELCOME TO PHILIPS - CHECKING SENSORS - CHECKING WATER

- WARMING UP’.

The steam light on the steam tank starts blinking.

After approx. 2 minutes the steam light stays on continuously to indicate

that the steam tank is ready for steam ironing.

When you switch the appliance on, it will automatically heat up to

the last used temperature setting.

2 Check the garment label for the required ironing temperature.

3 Press the temperature button + or - (hotter or colder) to set the

required ironing temperature or fabric type.

The display shows the fabric type for which the selectedtemperature

setting is most suitable (see chapter ‘Iron display guide’).

The display indicates that the iron is heating up or cooling down to

the selected temperature.

A double beep and a message on the display indicate that the soleplate has

reached the selected temperature.

Tips

If the article consists of various kind of bres, always select the

temperature required by the most delicate bre, i.e. the lowest

temperature. If, for example, the fabric consists of 60% polyester and

40% cotton, it should be ironed at the temperature indicated for

polyester (2).

If you do not know what kind or kinds of fabric an article is made of,

determine the right ironing temperature by ironing a part that will not

be visible when you wear or use the article.

Silk, woollen and synthetic materials: iron the reverse side of the fabric

to prevent shiny patches.

Fabrics that tend to acquire shiny patches should be ironed in one

direction only (along with the nap) while applying very little pressure.

Start ironing the articles that require the lowest ironing temperature,

i.e. those made of synthetic materials.

To make the iron cool down faster, simply apply steam or iron a

piece of cloth.

,

-

,

OnOn

MAXMAX

ENGLISH 9

Display menu

The GC8280 offers 5 functions that allow you to adjust the settings of the

appliance to your own preferences.

These functions are listed in a menu. You can use the menu by

pressing the menu button and the + and - buttons on the iron.

The menu structure of these functions is:

Steam lock (on)/off

Iron off: 5/10/20/(30) minutes

Sound: (on)/off

Language: (English)/Dutch/French/German/Italian/Spanish/Portuguese

Water hardness: soft/(medium)/hard

Note: the default settings are shown between brackets.

To select your preferred settings:

1 Press the menu button for 1 second.

2 Use the + and - buttons on the iron to scroll through the available

settings.

3 When you have reached the setting of your choice, press the menu

button again. The message ‘CONFIRMED’ appears on the display.

4 To exit the menu, wait 3 seconds.

Using the appliance

Steam ironing

The supply hose may become hot during a long ironing session.

Note: The system may occasionally produce a pumping sound during steam

ironing. This is normal and tells you that water is being pumped into the steam

tank.

1 Make sure there is enough water in the water tank.

2 Put the mains plug in an earthed wall socket and press the on/off

button once.

3 Select the recommended ironing temperature (see chapter ‘Preparing

for use’).

Steam ironing is only possible at ironing temperatures higher than 2.

The steam function will automatically be disabled at ironing temperatures

lower than 2.

4 Select the required steam setting by means of the + and - buttons on

the steam tank control panel.

p for maximum steam (temperature setting MAX).

[ for moderate steam (temperature settings 3 to MAX).

] for minimum steam (temperature settings 2 to MAX).

a for no steam (temperature settings 1 to MAX).

The steam light blinks to indicate that the steam tank is heating up.

After approx. 2 minutes the steam light stays on continuously to indicate

that the steam tank is ready for steam ironing.

During steam ironing, the steam light starts blinking from time to time to

indicate that the steam tank is heating up to maintain the right temperature

and pressure.

,

-

,

OnOn

ENGLISH10

During ironing you can adjust the steam setting by means of the +

and - steam buttons.

It will take a few moments before the amount of steam is adjusted.

5 Press the steam activator to start steam ironing.

When you put the iron down during ironing, put it on its heel or on the

iron stand.

The opening and closing of the steam valve in the steam tank will

cause a clicking sound. This is perfectly normal.

Steam lock function

The steam lock allows you to steam iron non-stop without having to press

the steam activator continuously.

When the steam lock function has been set to ‘on’ (the default

setting in the display menu), the iron starts steaming continuously

when the steam activator is pressed once. To stop steaming, press

the steam activator once again.

When the steam lock function has been set to ‘off’ (see section

‘Display menu’), the iron will only produce steam when the steam

activator is pressed.

Release the steam lock when you put the iron on its heel or on the iron

stand. This prevents hot steam from escaping from the iron or from wetting

the iron stand.

Ironing without steam

There are two ways to iron without steam:

1 You can simply start ironing without pressing the steam activator.

2 You can also select steam setting a (no steam) and start ironing.

Features

Vertical steaming

Never direct the steam at people.

You can steam iron hanging curtains and clothes (jackets, suits,

coats) by holding the iron in vertical position and pressing the steam

activator.

Iron-off function

The iron-off function automatically switches the soleplate off when the

steam activator has not been pressed for a particular number of minutes,

depending on the iron-off time you have selected.

You can select an iron-off time of 5, 10, 20 or 30 minutes (see section

‘Display menu’).

1 The display will show the text ‘IRON OFF’ and you will hear an

intermittent beep.

,

ENGLISH 11

2 If you want to start ironing again, press any button on the iron. The

soleplate will then start heating up again.

Note: the iron-off function switches the soleplate off but does not switch the

steam tank off. If you intend to stop ironing, you should switch the appliance

off and unplug the steam tank.

Cleaning and maintenance

After ironing

1 Put the iron on the stand and switch it off.

2 Remove the mains plug from the wall socket and let the iron cool

down.

3 Wipe scale and any other deposits off the soleplate with a damp

cloth and a non-abrasive (liquid) cleaner.

4 Clean the upper part of the appliance with a damp cloth.

5 Empty the water tank after cleaning.

Calc-Clean function

Never remove the Calc-Clean rinsing cap when the steam tank is hot.

VERY IMPORTANT: Rinse the steam tank once a month or after every

10 times of use to prevent damage to the appliance and for optimal

steaming performance.

1 Make sure that the appliance has been unplugged and has cooled

down for more than 2 hours.

2 Remove the detachable water tank.

3 Hold the steam tank with both hands and shake well.

4 Turn the steam tank on its side and remove the Calc-Clean rinsing

cap.

OffOff

ENGLISH12

5 Empty the steam tank by pouring out the water into the sink.

6 Fill the steam tank with fresh water by means of the lling cup and

shake again.

7 Empty the steam tank into the sink again.

Repeat steps 6 & 7 twice to obtain the best result.

8 Screw the Calc-Clean rinsing cap tightly back onto the steam tank.

Calc-Clean reminder

1 When the display shows the message ‘SWITCH OFF IRON - DO

CALC CLEAN’, too much scale has built up inside the appliance and

the steam tank needs to be rinsed.

2 Switch the appliance off immediately.

3 Use the Calc-Clean function as described above.

ENGLISH 13

Storage

Always let the iron cool down before storing it.

1 Insert the tip of the iron into the safe storage lock on the stand.

2 Press the back of the iron rmly down (‘click’).

3 Empty the water tank.

4 Pull out the cord & hose storage hook.

5 Secure the supply hose and mains cord.

6 There are handgrips on either side of the steam tank for easy

transport.

ENGLISH14

Environment

Do not throw the appliance away with the normal household waste

at the end of its life, but hand it in at an ofcial collection point for

recycling. By doing this you will help to preserve the environment.

Guarantee & service

If you need information or if you have a problem, please visit the Philips

website at www.philips.com or contact the Philips Customer Care

Centre in your country (you will nd its phone number in the worldwide

guarantee leaet). If there is no Customer Care Centre in your country,

contact your local Philips dealer or contact the Service Department of

Philips Domestic Appliances and Personal Care BV.

Iron display guide (Fig. 2)

Temperature settings suitable for specic fabric types.

Action Option Message in English

Switching the appliance on WELCOME TO PHILIPS - CHECKING

SENSORS - CHECKING WATER -

WARMING UP

Using the menu button (see

section ‘Display menu’)

Switching the steam lock

on or off

STEAM LOCK - ON - OFF -

CONFIRMED

Setting the iron-off time IRON OFF - 5 MIN - 10 MIN - 20 MIN

- 30 MIN - CONFIRMED

Switching the sound on

or off

SOUND - ON - OFF - CONFIRMED

Choosing a language LANGUAGE - ENGLISH - DUTCH

- FRENCH - GERMAN - PORTUGUESE

- SPANISH - ITALIAN - CONFIRMED

Setting the water hardness WATER HARDNESS - SOFT - MEDIUM

- HARD - CONFIRMED

Iron switches off after the

iron-off time has elapsed (see

section ‘Iron-off function’)

IRON OFF - STANDBY - PRESS ANY

KEY TO RESUME

Pressing the + and - buttons

(see section ‘Setting the

temperature’)

Choosing the fabric type ACETATE - ACRYLIC - VELVET - NYLON

- SILK - VISCOSE - POLYESTER - WOOL

- RAYON - COTTON - JEANS - LINEN

,

ENGLISH 15

Action Option Message in English

Iron warming up because

different fabric type has

been selected

WARMING UP

Iron cooling down because

different fabric type has

been selected

COOLING

Correct temperature for

selected fabric type has

been reached

TEMP OK

Water tank is empty or has

not been placed properly or

has not been placed at all

(see section ‘Water tank rell

light’)

WATER LOW - REFILL WATER TANK

Iron needs to be rinsed (see

section ‘Calc-Clean function’)

SWITCH OFF IRON - DO CALCCLEAN

Iron should not be used

(see chapter ‘Guarantee &

service’)

ERROR 01

Troubleshooting

This chapter summarises the most common problems you could encounter

with your iron. Please read the different sections for more details. If you

are unable to solve the problem, please contact the Philips Customer Care

Centre in your country.

Problem Cause Solution

The appliance does

not become hot.

There is a connection problem. Check the mains cord, the plug and

the wall socket.

The appliance has not been switched on. Press the on/off button.

The selected temperature is too low. Select a higher temperature.

Smoke comes out

of my new iron

when I switch it on.

Some parts of the appliance have been

lightly greased in the factory and may

initially give off some smoke when heated.

This phenomenon is perfectly

normal and will cease after a short

while.

The iron does not

produce any steam.

There is not enough water in the water

tank.

Fill the water tank (see ‘Preparing

for use’, section ‘Filling the

detachable water tank’).

The steam tank has not heated up

sufciently.

Wait for approx. 2 minutes until the

steam light stays on continuously).

The selected ironing temperature is too

low for steam ironing.

Select a temperature of 2 or

higher.

ENGLISH16

Problem Cause Solution

Steam setting a (no steam) has been

selected.

Select steam setting ] (minimum

steam), [ (moderate steam) or p

(maximum steam).

The water tank has not been placed

properly in the steam tank.

Place the water tank properly in the

steam tank (‘click’).

When the iron has been set to a very high

temperature, the steam produced is dry

and hardly visible. It will be even less visible

when the ambient temperature is relatively

high and it will be entirely invisible when

the temperature has been set to MAX.

Set the iron to a lower temperature,

e.g. 2, to check if the iron is

actually producing steam.

Water droplets

come out of the

soleplate.

When you start steam ironing and when

you have stopped steam ironing for a

while, the steam that was still present in

the supply hose will have cooled down

and condensed into water, which causes

water droplets to come out of the

soleplate.

This is perfectly normal. Hold the

iron over an old cloth and press

the steam activator when you start

ironing (again). Wait until steam

instead of water comes out of the

soleplate.

Flakes and impurities

come out of the

soleplate or the

soleplate is dirty.

Impurities or chemicals present in the

water have deposited in the steam vents

and/or on the soleplate.

Clean the soleplate with a damp

cloth.

’ERROR’ has

appeared on the

display and the iron

beeps continuously.

A sensor failure has been detected. Contact an authorised Philips

service centre.

The appliance

produces a pumping

sound.

Water is being pumped into the steam

tank.

This is normal.

The pumping sound does not stop. Unplug the iron immediately and

contact an authorised Philips service

centre.

Dirty water comes

out of the soleplate.

Too much scale and minerals have

accumulated inside the steam tank.

Rinse the steam tank. See chapter

‘Cleaning and maintenance’.

The iron produces

steam continuously.

The steam lock has been set to ‘on’. Press the steam activator again to

stop steaming. Set the steam lock

to ‘off ’ if you only want to obtain

steam when pressing the steam

activator (see section ‘Steam lock

function’).

ENGLISH 17

Problem Cause Solution

Steam escapes from

under the Calc-

Clean rinsing cap

when the appliance

is heating up.

The Calc-clean rinsing cap has not been

tightened properly.

Switch the appliance off, tighten the

Calc-Clean rinsing cap and switch

the appliance on again. If steam

continues to escape when the

appliance is heating up, switch the

appliance off and contact a service

centre authorised by Philips.

The iron does not

produce enough

steam/the amount

of steam decreases

and increases during

steam ironing.

When the appliance pumps water into

the boiler, the steam amount sometimes

decreases. This is probably when you think

that the iron does not produce enough

steam. However, this is a completely

normal phenomenon and the steam

output normalises within a few seconds.

To optimise the steam output,

release the steam lock when you do

not need steam and when you put

the iron down.

Wet spots appear

on the garment

during ironing.

The wet spots that appear on your

garment after you have steam ironed for

some time may be caused by steam that

has condensed onto the ironing board.

Iron the wet spots without steam for

some time to dry them. If the underside

of the ironing board is wet, wipe it with a

piece of dry cloth.

To prevent steam from condensing

onto the ironing board, use an

ironing board with a wire mesh top.

ENGLISH18

19

Introduktion

Tak fordi du har købt Philips GC8280. Læs venligst brugsvejledningen, da

den indeholder oplysninger om strygesystemets overraskende funktioner

samt nogle gode råd, der gør strygningen lettere og mere behagelig.

Det kraftfulde Philips GC8280-strygesystem med tryk producerer konstant

damp, hvilket gør strygningen lettere. Takket være den store vandtank kan

du stryge uden afbrydelse. Når vandtanken er tom, tages den blot af og

fyldes igen.

Philips GC8280 er udstyret med et avanceret display, der giver dig kontrol

over strygeprocessen. Displayet viser den valgte temperaturindstilling og

har præcise, forprogrammerede temperaturindstillinger til 12 forskellige

materialer. Det informerer dig tillige om dampindstilling og vandstand og

husker dig på, når strygejernet skal rengøres. Strygejernet er meget sikkert

at anvende takket være autosluk-funktionen. Sidst men ikke mindst, er det

det eneste strygesystem på markedet med integreret drypstopfunktion.

Vi håber, at du vil nyde brugen af Philips GC8280.



A Dampslange

B Håndtag med blødt greb

C Dampaktiveringsknap

D Display

E Temperatur-taster (+/-)

F Menu-tast

G Strygesål

H Lås til sikker opbevaring

I Holder til strygejernet

J Aftagelig vandtank

K Påfyldningsbæger

L Krog til opbevaring af ledning og slange

M Calc-Clean-dæksel

N Påfyldningsåbning

O Udløser til vandtank

P Damptank

Q On/off-kontakt med lys

R Transporthåndtag

S Indikator for påfyldning af vandtank

T Netledning

U Damp-taster (+/-)

V Betjeningspanel på damptanken med lysindikator for damp

p = maksimal dampmængde

[ = moderat dampmængde

] = minimal dampmængde

a = ingen damp

Vigtigt

Læs denne brugsvejledning omhyggeligt igennem, inden apparatet tages i

brug, og gem den til eventuelt senere brug.

Kontrollér, om spændingsangivelsen på typeskiltet svarer til den

lokale netspænding, før du tilslutter apparatet.

Apparatet må kun sluttes til en stikkontakt med jordforbindelse.

-

,

DANSK

Brug ikke apparatet, hvis stik, ledning, dampslange eller selve

apparatet viser tegn på beskadigelse, eller hvis apparatet er blevet

tabt, eller det er utæt.

Kontrollér med jævne mellemrum, at ledningen og dampslangen er

hel og ubeskadiget.

Hvis ledningen eller dampslangen beskadiges, må de kun udskiftes af

Philips, et autoriseret Philips-serviceværksted eller af en kvaliceret

fagmand for at undgå enhver risiko ved efterfølgende brug.

Hold altid apparatet under opsyn, når det er sluttet til lysnettet.

Hverken strygejern eller damptank må kommes ned i vand.

Dette apparat er ikke beregnet til at blive brugt af personer

(herunder børn) med nedsatte fysiske og mentale evner, nedsat

følesans eller manglende erfaring og viden, medmindre de er blevet

vejledt eller instrueret i apparatets anvendelse af en person, der er

ansvarlig for deres sikkerhed.

Apparatet bør holdes uden for børns rækkevidde for at sikre, at de

ikke kan komme til at lege med det.

Strygesålen kan blive utrolig varm og forårsage brandsår ved

berøring.

Netledning og dampslange må ikke komme i kontakt med

strygesålen, når denne er varm.

Når du er færdig med at stryge, når du rengør apparatet, når du

fylder eller tømmer vandtanken, og når du forlader strygejernet

– selv om det kun er i et kort øjeblik – skal du placere strygejernet i

standeren, slukke for apparatet og tage stikket ud af stikkontakten.

Placér og brug altid strygejern og damptank på et stabilt, plant og

vandret underlag. Damptanken må ikke stilles på den bløde del af

strygebrættet.

Hvis der slipper damp ud under Calc-Clean-dækslet, mens apparatet

varmer op, skal du slukke for apparatet og stramme Calc-Clean-

dækslet. Slipper der fortsat damp ud, mens apparatet varmer op, skal

du slukke for apparatet og kontakte din Philips-forhandler.

Brug ikke andre låg til damptanken end det medleverede, da det

samtidig fungerer som sikkerhedsventil.

Skyl damptanken med jævne mellemrum ifølge anvisningerne i

afsnittet “Rengøring”.

Calc-Clean-dækslet må aldrig fjernes, når damptanken er varm.

Dette apparat er kun beregnet til privat brug.

Elektromagnetiske felter (EMF)

Dette Philips-apparat overholder alle standarder for elektromagnetiske

felter (EMF). Ved korrekt anvendelse i overensstemmelse med

instruktionerne i denne brugsvejleding, er apparatet sikkert at anvende,

ifølge den videnskabelige viden, der er tilgængelig i dag.

Før apparatet tages i brug første gang

Bemærk: Der kan komme lidt røg fra strygejernet, når det tændes første gang.

Dette er helt normalt og vil hurtigt forsvinde.

Bemærk: Når strygejernet bruges første gang, kan der drysse lidt partikler ud

fra strygesålen. Dette er helt normalt. Partiklerne er uskadelige og forsvinder

efter et kort øjeblik.

,

DANSK20

Sayfa yükleniyor ...

Philips GC8280 El kitabı

Philips GC8280 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler