Yamaha DV-SL100 El kitabı

Kategori
Dvd oynatıcılar
Tip
El kitabı
DVD / VIDEO CD / CD PLAYER
LECTEUR DE DVD
DV-SL100
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
G
3139 246 13251
DV-SL100
DV-SL100(G)
IP
Printed in China
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©2003 YAMAHA CORPORATION All rights reserved.
DK
Advarsel:
Laserrudstråling ved åbning når sikkerhesafbrydere er ude
af funktion. Undgå u tsættelse for stråling.
Bemærk:
Netafbryderen STANDBY/ON er sekundært indkoblet og
afbryder ikke strømmen fra nette. Den indbyggede netdel
er derfor tilsluttet til lysnettet så længe netstikket sidder i
stikkontakten.
N
Observer:
Nettbryteren STANDBY/ON er sekundert innkoplet. Den
innebygdenetdelen er derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
S
Klass 1 laserapparat
Varning!
Om apparaten används på annat sätt än i denna
bruksanvisning specificerats, kann användaren utsättas för
laserstrålning, som översjruder gränsen för läserklass 1.
Observera!
Strömbrytaren STANDBY/ON är sekundärt kopplad och
inte bryter strömmen fråan nätet Den inbyggda nätdelen
är därför ansluten till elnätet så länge stickproppen sitter i
v ägguttaget.
SF
Luokan 1 laserlaite + Klass 1 laserapparat
Varoitus!
Laitteen käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle lasersäleilille.
Huom.
Toiminnanvalitsin STANDBY/ON on kytketty
toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.
Sisäänrakennettu verkko-osa on kytkettynä
sähköverkkoon aina silloin, kun pistoke on pistorasiassa.
Important Note for Users in the UK
markings identifying the terminals in your plug, proceed as
follows:
Connect the blue wire to the terminal marked N or
coloured black.
Connect the brown wire to the terminal marked L or
coloured red.
•Do not connect either wire to the earth terminal in the
plug, marked E (or e) or coloured green (or green and
yellow).
Before replacing the plug cover, make certain that the cord
grip is clamped over the sheath of the lead - not simply
over the two wires.
Copyright in the U.K.
Recording and playback of material may require
consent. See Copyright Act 1956 and The
Performer’s Protection Acts 1958 to 1972.
Mains plug
This apparatus is fitted with an approved 13 Amp plug.To
change a fuse in this type of plug proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp, A.S.T.A.
or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it
should be cut off and an appropriate plug fitted in its place.
If the mains plug contains a fuse, this should have a value of
5 Amp. If a plug without a fuse is used, the fuse at the
distribution board should not be greater than 5 Amp.
Note:The severed plug must be disposed of to avoid a possible
shock hazard should it be inserted into a 13 Amp socket
elsewhere.
How to connect a plug
The wires in the mains lead are coloured with the following
code: blue = neutral (N), brown = live (L).
As these colours may not correspond with the colour
VARO!
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTIINA NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ
KATSO SÄTEESEEN.
VARNING!
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRREN ÄR URKOPPLAD.
BETRAKTA EJ STRÅLEN.
Important Note
i
General information
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
ATTENTION
L’emploi de commandes, de réglages ou un choix de
procédures différents des spécifications de cette
brochure peut entraîner une exposition à d’éventuelles
radiations pouvant être dangereses.
ACHTUNG
Die Verwendung von Bedienungselementen oder
Einstellungen oder die Durchführung von
Bedienungsvorgängen, die nicht in dieser Anleitung
aufgeführt sind, kann zu einem Kontakt mit gefährlichen
Laserstrahlen führen.
OBSERVERA
Användning av kontroller och justeringar eller
genomförande av procedurer andra än de som
specificeras i denna bok kan resultera i att du utsätter
dig för farlig strålning.
ATTENZIONE
Uso di controlli o regolazioni o procedure non
specificamente descritte può causare l’esposizione a
radiazioni di livello pericoloso.
PRECAUCIÓN
El uso de los controles o los procedimientos de ajuste o
utilización diferentes de los especificados en este
manual pueden causar una exposición peligrosa a la
radiación.
VOORZICHTIG
Gebruik van bedieningsorganen of instellingen, of
uitvoeren van handelingen anders dan staan beschreven
in deze handleiding kunnen leiden tot blootstelling aan
gevaarlijke stralen.
The unit is not disconnected from the AC power source as
long as it is connected to the wall outlet,even if this unit itself
is turned off.This state is called the standby mode.In this
state,this unit is designed to consume a very small quantity of
power.
L ’appareil n ’est pas isolé de la source d ’alimentation aussi
longtemps qu ’il reste branché sur une prise murale,même
lorsqu ’il est éteint.Il est alors dit en mode «Veille ».Dans ce
mode, l ’appareil consomme très peu de courant.
Das Gerät ist nicht vom Netz getrennt, solange der
Netzstecker noch mit der Wandsteckdose verbunden ist,
selbst wenn das Gerät ausgeschaltet wurde. Dieser
Betriebszustand wird als Bereitschaftsmodus bezeichnet. In
diesem Zustand nimmt das Gerät eine sehr geringe Menge
Strom auf.
Enheten är inte urkopplad från nätet så länge som den är
ansluten till vägguttaget även om enheten i sig självt är
avstängd. Detta kallas för beredskapsläge och i detta tillstånd
konsumerar apparaten minimalt med ström.
L’unità non è scollegata dall’impianto elettrico di casa sintanto
che rimane collegata ad una presa di corrente anche se è
spenta. Questo modo viene chiamato “modo di attesa”. In
esso, l’unità consuma una quantità molto bassa di energia per
mantenere in memoria le impostazioni da voi fatte.
Aunque el propio aparato se encuentre apagado, éste no se
desconectará de la fuente de CA siempre que se mantenga
enchufado a la toma de corriente. Este estado recibe el
nombre de “modo de espera”. En este estado, este aparato ha
sido diseñado para consumir una cantidad muy pequeña de
energía.
De stroomtoevoer naar het toestel is niet afgesloten zolang
de stekker nog in het stopcontact zit, zelfs niet als het toestel
zelf uitgeschakeld is. Deze toestand wordt “standby” (waak- of
paraatstand) genoemd. Het toestel is ontworpen om in deze
toestand
CAUTION VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED
ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR
DEKSEL ÅPNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING
NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA
NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN
VORSICHT SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET
NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE
EN CAS D’OUVERTURE EXPOSITION DANGEREUSE AU
FAISCEAU
ii
le laser
CAUTION
- Visible and invisib
radiation when open. Avoid exposure to beam.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2
Install this sound system in a well ventilated, cool, dry,
clean place — away from direct sunlight, heat sources,
vibration, dust, moisture, or cold. In a cabinet, allow
about 2.5cm (1 inch) of free space all around this unit
for adequate ventilation.
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause
an electrical shock, fire, damage to this unit, and/or
personal injury.
5 Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of
this unit, do not place:
Other components, as they may cause damage and/
or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may cause fire,
damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical shock to
the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If
the temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage.
9 Do not use excessive force on switches, knobs and/or
cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Use only the voltage specified on this unit. Using this
unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than as specified.
13 To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any service
is needed. The cabinet should never be opened for any
reason.
15 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this
unit is faulty.
17 Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power
plug from the wall outlet.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
NOTE:
Pictures shown maybe different between countries.
Never make or change connections with the power
switched on.
When playing DTS encoded CDs, excessive noise will be
heard from the analog stereo outputs. To avoid possible
damage to the audio system, the consumer should take
proper precautions when the analog stereo outputs of the
player are connected to an amplification system. To enjoy
DTS Digital Surround™ playback, an external 5.1-channel
DTS Digital Surround™ decoder system must be
connected to the digital output of the player.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or
attempt to service this device.
CAUTION
VISIBLE AND INVISIBLE LASER RADIATION WHEN
OPEN. AVOID EXPOSURE TO BEAM (WARNING
LOCATION: INSIDE ON LASER COVERSHIELD OR THE
BACKPLATE OF SET)
LASER
Type Semiconductor laser GaAlAs
Wave length 650 nm (DVD)
780 nm (VCD/CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
DANGER
This unit emits visible laser radiation when open. Avoid
direct eye exposure to beam.
When this unit is plugged into a wall outlet, do not place
your eyes close to the opening of the disc tray and other
openings or look inside.
iii
1
English
Introduction
Environmental Information ....................................................2
Supplied accessories ................................................................2
Notes about discs ....................................................................2
Cleaning discs ........................................................................................... 2
Symbols Used in this Manual .................................................2
Functional Overview
Front and Rear Panels .............................................................3
Remote Control .......................................................................4
Preparation
General Notes on connections.............................................5
Digital Connections .................................................................5
Analog Connections ................................................................5
Video Connections ..................................................................6
S VIDEO terminal <A>...................................................................... 6
VIDEO terminal <B>........................................................................... 6
COMPONENT VIDEO terminal <C>..................................... 6
SCART Connection <D>................................................................. 6
Connecting an AV receiver with a SCART terminal .......6
Inserting batteries into the Remote Control.....................7
Using the Remote Control............................................................... 7
PAL/NTSC Conversion...........................................................7
Turning on the power.............................................................7
Smart Power On/Off...............................................................7
Operation
Basic Playback............................................................................8
General Operation...................................................................8
Video control during playback........................................................ 8
Audio control during playback........................................................ 8
Repeat and Shuffle................................................................................. 9
Repeat A-B ................................................................................................ 9
Disc Resume ............................................................................................. 9
OSD (On-Screen Display)................................................................ 9
Zoom ......................................................................................................... 10
Special DVD Features .......................................................... 10
Playing a Title......................................................................................... 10
Playing a Chapter................................................................................. 10
Camera Angle ....................................................................................... 10
Changing the Audio Language and/or format .................... 10
Subtitles..................................................................................................... 10
Special VCD & SVCD Features.......................................... 10
Playback Control (PBC) .................................................................. 10
Preview Function................................................................................. 11
JPEG & MP3 CD Playback
General Operation................................................................ 12
MP3 & JPEG Navigator .................................................................... 12
Play Mode................................................................................................ 12
Special JPEG Features........................................................... 13
Function Introduction........................................................................ 13
Preview Function ................................................................................. 13
Zoom picture ........................................................................................ 13
Playback with multi-angles.............................................................. 13
Wipe Effect............................................................................................. 13
Special MP3 Features............................................................ 13
Function Introduction........................................................................ 13
JPEG and MP3 simultaneous playback .............................. 13
Setup Menu
Basic Operation ..................................................................... 14
General Setup menu............................................................. 14
DISC LOCK............................................................................................ 14
PROGRAM (not for JPEG / MP3 CD) ................................... 14
OSD LANGUAGE............................................................................. 15
SCREEN SAVER .................................................................................. 15
Audio Setup menu................................................................. 15
SPEAKER SETUP ................................................................................. 15
DIGITAL AUDIO SETUP............................................................... 16
EQUALIZER (Sound Mode)......................................................... 16
3D (REVERB MODE)....................................................................... 16
Video Setup menu................................................................. 17
TV TYPE................................................................................................... 17
TV DISPLAY........................................................................................... 17
CLOSED CAPTION ......................................................................... 18
COMPONENT .................................................................................... 18
PROGRESSIVE...................................................................................... 18
PICTURE SETTING ........................................................................... 18
PASSWORD SETUP............................................................. 19
Preference Setup menu........................................................ 20
AUDIO language................................................................................. 20
SUBTITLE language ............................................................................ 20
DISC MENU language...................................................................... 20
PARENTAL Control.......................................................................... 21
DEFAULT Setup.................................................................................. 21
MP3/JPEG NAV.................................................................................... 21
Troubleshooting....................................22
Specifications.........................................23
Maintenance ..........................................23
Language Code......................................24
Contents
2
Thank you for purchasing this unit. This Owner’s Manual
explains the basic operation of this unit.
The region code for this set is 2.
Since it is usual for DVD movies to be
released at different times in different regions
of the world, all players have region codes and discs can
have an optional region code. This unit can play discs
containing the identical region code, or mentioned as
region “ALL”. If you load a disc of a different region code
to this unit, you will see the region code notice on the
screen. The disc will not play, and should be unloaded.
Environmental Information
This unit consists of materials which can be recycled and
reused if disassembled by a specialised company. Please
observe the local regulations regarding the disposal of
packaging materials, exhausted batteries and old
equipment.
Supplied accessories
Remote control
Batteries (two AA size) for remote control
Audio pin cable
Video pin cable
Owner’s Manual
Notes about discs
– This unit is designed for use with DVD video, Video CD,
Super video CD, Audio CD, CD-R, CD-RW (MP3 Supported),
DVD+RW, DVD+R, DVD-R and DVD-RW.
– CD-R and CD-RW cannot be played unless finalized.
Some discs cannot be played depending on the recording
conditions such as PC environment and application software.
The characteristics and condition of the discs; materials,
scratches, curvature, and etc, may result in failure.
– Be sure to use only CD-R and CD-RW discs made by
reliable manufacturers.
– Do not use any non standard shaped discs (heart, etc.)
– Do not use disc with tape, scals, or paste on it, damage
to the unit may result.
Do not use a disc printed on its surface by a commercially
available label printer.
Cleaning discs
When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the centre out. Do not wipe in a
circular motion.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
Symbols Used in this Manual
The below symbols appear in some headings and notes
with the following meanings:
Some DVD video discs require specific functions
or allow only limited functions during playback.
Ä
” may appears on the TV screen which
means that the function is not available on that
specific DVD video disc.
2
Manufactured under license from Dolby Laboratories. “Dolby”
and the double-D symbol are trademarks of Dolby
Laboratories.
”DTS” and ”DTS Digital Out” are trademarks of Digital
Theater Systems, Inc.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and
other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohibited.
DVD
VCD
CD
– Description refers to playback of DVD-
video discs
– Description refers to playback of Video CDs
– Description refers to playback of Audio CDs
– Description refers to playback of Super
VCDs
SVCD
SVCD
Introduction
3
English
Front and Rear Panels
Caution: Do not touch the inner pins of the jacks on the rear panel.
Electrostatic discharge may cause permanent damage to the unit.
STANDBY/ON
to turn this unit to standby mode or
ON
Disc Tray
/ OPEN/CLOSE
to open/close the disc tray
B PLAY
– to start playback
; PAUSE
– to interrupt playback
9 STOP
– to stop playback
S VIDEO
COAXIAL
connect to S-Video input of your AV
receiver
connect to DIGITAL INPUT of your
AV receiver
connect to DIGITAL INPUT of your
AV receiver
VIDEO
connect to Video inputs of your AV
receiver
OPTICAL
MAINS
COMPONENT VIDEO OUT
– connect to a standard AC outlet
– connect to component video inputs of
your AV receiver
– connect to a TV with SCART
TV OUT
– connect to AUDIO inputs of your
AV receiver or stereo system
AUDIO OUT (Left/Right)
Functional Overview
4
Remote Control
* Press and hold button for about two seconds.
B/
|
turn this unit ON or go to
standby-on mode
0-9 numeric buttons
select numbered items in a menu
ON SCREEN
access or remove player’s On
Screen Display menu
SETUP
access or remove player’s setup
menu
T
search forward* / next chapter or
track
SUBTITLE
subtitle language selector
ANGLE
select DVD camera angle
ZOOM
enlarge video image
AUDIO
audio language and format
selector
TOP MENU/RETURN
– display the top-level disc menu
(DVD) / go back to previous menu
(VCD)
MENU
– access menu of a disc (DVD) /
switch PBC on/off (VCD)
1 2 3 4
– (left/right/up/down) select an item
in the menu
ENTER/OK
– acknowledge menu selection
S
– search backward* / go to a
previous chapter or track
STOP ( 9 )
– stop playback
PLAY ( B )
– start playback
PAUSE ( ; )
– pause playback temporarily /
frame-by-frame playback
REPEAT
– repeat chapter, track, title, disc /
shuffle chapter, track
A-B
– repeat a specific segment
SCAN
– preview the content of a track or
whole disc (VCD) / play the first 6
seconds or less of each track (CD)
MUTE
– disable or enable sound output
Functional Overview
5
English
General Notes on connections
Never make or change connections with the power
switched on.
Depending on the equipment you wish to connect, there
are various ways you could connect this unit. Possible
connections are shown in the following drawings.
Please refer to the manuals of other equipment as
necessary to make the best connections.
Do not connect this unit via your VCR. The video quality
could be distorted by the copy protection system.
Do not connect this unit’s audio out jack to the phono in
jack of your audio system.
Digital Connections
This unit has COAXIAL and OPTICAL digital out jacks.
Connect one or both of them to your AV receiver
equipped with Dolby digital, DTS, or MPEG decoder
using each specific cable (separate purchase).
You will need to set this unit’s digital output to
All (see ‘DIGITAL OUTPUT’).
Note:
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will produce a
strong, distorted sound or no sound at all. Make sure to
select the appropriate audio format at menu screen
included on the disc.
Pressing AUDIO once or more may change not only audio
languages but also audio formats, and the selected format
appears for several seconds on the status window.
Analog Connections
Use audio/video cable supplied with this unit to connect
AUDIO OUT L (left) and R (right) jacks of this unit to
corresponding input jacks of your audio equipment such
as Stereo amplifier.
AV receiver
COAXIAL
IN
OPTICAL
IN
C
O
Stereo
amplifier
(supplied)
1 CD/DVD
RL
R
L
L
R
Preparation
6
Video Connections
If your AV receiver has video output jacks, connect your
receiver (and then to your TV) so that you can use one
TV for several different video sources (LD, VCR etc.) by
simply switching the input source selector of your
receiver.
The player has four types of video output jacks. Use one
of them in accordance with the input jacks of the
equipment to be connected.
S VIDEO terminal <A>
S (separate) video connection achieves a clearer picture
than composite video connection by separating color and
luminance when transmitting signals. Use commercially
available S-video cable. Receiver (and TV) with S-video
input is required.
VIDEO terminal <B>
Use audio/video cable supplied with this unit when
connecting the player to a TV.
COMPONENT VIDEO terminal <C>
Component video connection achieves high fidelity in
reproducing colors (better performance than S-video
connection), separating video signal into luminance (Y,
terminal color-coded as green), and color difference (Pb,
blue/Pr, red). Use commercially available coaxial cables.
Receiver (and TV) with component input is required.
Observe the color of each jack when connecting. If your
receiver does not have component output jacks,
connecting the player’s component output directly to
your TV’s component input can reproduce better video
image.
SCART Connection <D>
If your TV has only terminal for video input, and you want
to connect it directly to this unit, you can use this unit’s
TV OUT jack.
Note:
– Ensure that the “TV” indication on SCART cable is
connected to the TV set and “DVD” indication on SCART
cable is connected to this unit.
Connecting an AV receiver with a
SCART terminal
If your AV receiver has SCART terminals, you can
connect this unit’s TV OUT to your AV receiver’s SCART
terminal.
VIDEO
OUT
VIDEO
IN
COMPONENT
VIDEO OUT
COMPONENT
VIDEO IN
S VIDEO
OUT
S VIDEO
IN
COMPONENT
VIDEO IN
S VIDEO
INPUT
VIDEO
YPBCB PRCR
<C><A>
AV receiver
<B>
<D>
(supplied)
S
V
AV receiver
Preparation
7
English
Inserting batteries into the Remote
Control
1
Open the battery cover by pressing in the tab, then lift off
the cover.
2
Insert batteries with the correct polarity as indicated by
the +
and -
symbols inside the battery compartment.
3
Close the cover.
CAUTION!
Remove batteries if they are exhausted or not to
be used for a long time.
– Do not use old and new or different types of
batteries in combination.
– Batteries contain chemical substances, so they
should be disposed off properly and kept away
from children.
Using the Remote Control
Direct the remote control at the remote sensor of the
DVD player.
Do not drop or give the remote control a shock.
Do not leave the remote control in extremely hot or
humid places.
Do not spill water or put anything wet on the remote
control.
PAL/NTSC Conversion
This player is equipped with a PAL/NTSC conversion
feature to convert the video output of the disc to match
your TV system. The conversions supported are as
below. To activate the conversion, refer to “TV TYPE”:
Notes:
– “MULTI” can only be selected when using a TV that has
both the PAL and NTSC systems.
Slight picture distortions may occur due to this conversion.
This is normal. Thus, the “MULTI” is most suitable for the
best picture quality.
Turning on the power
1
Connect the AC power cord to the power outlet.
2
Turn on the TV and your AV receiver.
3
Select the appropriate input source at the AV receiver
that was used to connect to this unit. Refer to the
equipment owner’s manual for detail.
4
Turn this unit on.
5
Set the TV to the correct Video IN channel. (eg. EXT1,
EXT2, AV1, AV2, AUDIO/VIDEO, etc. (Refer to your TV
owner’s manual for detail)
The front display lights up and the default screen
appears on the TV.
Smart Power On/Off
When in STOP or NO DISC mode, the DVD player will
switch to standby mode after 15 minutes without any
operations for saving energy. It is easily reactivated by
pressing the POWER or PLAY on the remote control or
the STANDBY/ON button on the front panel.
+
-
+
-
DVD
VCD
NTSC
NTSC
NTSC
NTSC
NTSC
NTSC
NTSC NTSC
PAL
PAL
PAL
PAL
Type Format
Disc Output format
Selected mode
NTSC
PAL
PAL
PAL
PAL
PAL MULTI
Preparation
8
Basic Playback
1
Press STANDBY/ON on the front panel to turn on the
DVD player.
2
Press
/
(OPEN/CLOSE) on the front panel to open disc
loading tray.
3
Place the chosen disc in the tray, with the label facing up.
4
Press
/
(OPEN/CLOSE) again to close the tray.
After recognizing this disc, the player begin to
playback automatically.
Notes:
– DVDs may have a region code. Your player will not play
discs that have a region code different from the region code
of your player.
If ‘DISC LOCK’ is set to LOCK and the disc inserted is not
authorized, the 6-digit code must be entered and/or the disc
must be authorized (see ‘DISC LOCK’).
General Operation
Note: All instructions set out below refer to the remote
control, unless otherwise stated.
Video control during playback
STOP
1
You can resume the play from the point at which you
stopped last time, if you just press STOP once. It will start
from the beginning if you press STOP twice to stop
playback.
PAUSE/STEP
1
To get a still picture, press PAUSE during playback.
2
To step forward to the next frame picture, press PAUSE
again.
3
To resume normal playback, press PLAY.
SKIP
1
Press
¡1
or
2™
briefly during playback to go to the next
chapter/track or to return to the beginning of the currect
chapter/track respectively.
2
Press
¡1
twice briefly to step back to the previous
chapter/track.
3
To go directly to any chapter/track, enter the chapter/
track number using the numeric buttons and press
ENTER/OK.
Note: Press and hold
2™
or
¡1
for more than two seconds
to search forward or backward.
SEARCH
1
To search the contents in fast speed, press
2
or
1
for fast
forward/backward searching.
2
Press
2
or
1
again to increase the speed for searching.
3
Press PLAY to return to normal playback.
Slow Motion
1
To get a slow motion effect during playback, press
3
or
4
.
2
Press
3
or
4
again, you can get different playback
forward/backward speeds.
3
Press PLAY to return to normal play back.
1
To get a slow motion effect during playback, press
4
.
2
Press
4
again, you can get different playback forward
speeds.
3
Press PLAY to return to normal play back.
Note: The SLOW BACKWARD function is not available for
VCD/Super VCD discs.
Audio control during playback
MUTE
1
Press MUTE to disable the sound output.
2
Press MUTE again to deactivate the mute.
Audio channel selection
1
Super VCD has two stereo audio channels which are
used for playing karaoke or the audio language selection.
(for instance, you can choose one channel for only the
music background of the song while you play the
karaoke.)
2
Press AUDIO to select the audio channels you want.
3
VCD has only one stereo audio channel, you can select
STEREO, MONO LEFT, MONO RIGHT or MIX-
MONO by pressing AUDIO.
STEREO: Output the left and right audio channels of
the disc through the left and right audio jacks accordingly.
MONO LEFT: Output the left audio channels of the
disc through the left and right audio jacks.
MONO RIGHT: Output the right audio channels of
the disc through the left and right audio jacks.
MIX-MONO: each of the audio jacks can output the
same audio effect as stereo.
DVDDVD
VCDVCD
CDCD
SVCDSVCD
DVDDVD
VCDVCD
CDCD
SVCDSVCD
DVDDVD
VCDVCDVCD
CDCD
SVCDSVCDSVCD
DVDDVD
VCDVCD
SVCDSVCD
DVDDVD
VCDVCDVCD
CDCD
SVCDSVCDSVCD
VCDVCD
CDCD
SVCDSVCD
Operation
9
English
Repeat and Shuffle
Each time you press REPEAT, the Repeat/Shuffle mode
changes as follows;
* This feature may not be available with some discs.
With PBC OFF,
Each time you press REPEAT, the Repeat/Shuffle mode
changes as follows;
Repeat A-B
DVD-Video Discs: repeat a sequence in a title
Video and Audio CDs: repeat a sequence in a track
1
Press A-B at your chosen starting point.
2
Press A-B again at your chosen end point.
The repeat sequence begins.
3
To exit the sequence, press A-B.
Disc Resume
This player can resume playback of the last 5 discs, even
if the disc was ejected or the power switched off.
1
Load one disc, which is one of the last 5 discs.
2
Press PLAY while “LOADING” is displayed on the
screen. If the information of this disc has been stored in
the memory of DVD player, it will be played back from
the stop point last time.
OSD (On-Screen Display)
This function will provide some information about your
playing disc on the screen.
Press ON SCREEN.
The Status window appears on the TV.
Title/Chapter/Track selection
1
Press
34
to select “TITLE” or “CHAPTER” (DVD) or
“TRACK” (VCD).
2
Press ENTER/OK.
3
Select a title, chapter or track number using the numeric
buttons.
Time Search
1
Press
34
to select “TT TIME” or “CH TIME”(DVD) or
“TRACK TIME” or “DISC TIME”(VCD).
“TT TIME” refers to the total time of the current title,
and the “CH TIME” refers to the total time of the current
chapter.
2
Press ENTER/OK.
3
Enter hours, minutes and seconds from left to right using
the numeric buttons. (e.g. 0:34:27)
Audio/Subtitle/Angle
You can change “AUDIO”, “SUBTITLE” or “ANGLE” if
available on the disc you are playing.
1
Press
34
to select “AUDIO”, “SUBTITLE” or “ANGLE”.
2
Press ENTER/OK.
3
For Audio and Subtitle,
Press
34
to highlight your selection and press ENTER/
OK.
or
For Angle,
Select an angle using the numeric buttons.
Repeat/Time Display
1
Press
34
to select “REPEAT” or “TIME DISP.”.
2
Press ENTER/OK.
3
Press
34
to highlight your selection and press ENTER/
OK.
Time display
Each time you press ON SCREEN, the time display
changes as follows;
DVDDVD
Chapter Repeat* Title Repeat
ShuffleShuffle RepeatRepeat/Shuffle Off
VCDVCD
CDCD
Track Repeat Disc Repeat
ShuffleShuffle RepeatRepeat/Shuffle Off
DVDDVD
VCDVCD
CDCD
DVDDVD
VCDVCD
CDCD
SVCDSVCD
DVDDVD
VCDVCD
DVDDVD
VCDVCD
DVDDVD
DVDDVD
VCDVCD
CDCD
Total Elapsed Total Remain
Single ElapsedSingle Remain
Operation
10
Zoom
The Zoom function allows you to change the image size.
1
Press ZOOM to activate the function.
Use
341
2
to view other parts of the zoomed
picture.
Playback will continue.
2
Press ZOOM repeatedly to return to the original size.
Special DVD Features
Playing a Title
A DVD disc may have one or more titles. This depends
on the content (a movie, video clips, a drama series, etc.)
on the disc.
After you load a disc, information about the content
shows on the screen waiting for your selection. You can
also press TOP MENU to turn back to the title menu
during playback.
Press the appropriate numeric buttons or
341
2
to
highlight your selection.
Press ENTER/OK to confirm.
Playing a Chapter
When you have selected a title, it may include one or
more chapters.
Any time you want to watch another chapter during
playback, press MENU to turn back to the chapter menu
(If disc has chapter menu).
Press the appropriate numeric buttons or
341
2
on
the remote control to highlight your selection.
Press ENTER/OK.
After a chapter has been selected, you also can press
¡1
or
2™
to make a change.
Camera Angle
Some discs contain scenes which have been shot
simultaneously from various angles.
This DVD player allows you to select the desired camera
angle.
Press ANGLE on your remote control.
Note: The function is available only for the DVD discs which
have several angles recorded.
Changing the Audio Language and/or
format
Press AUDIO repeatedly to select the different
languages.
Note: The function will be activated only if the DVD is
recorded with multi-language audio tracks.
Subtitles
Press SUBTITLE repeatedly to select the different
subtitles.
Note: The function will be activated, only if the DVD or
Super VCD is recorded with multi-subtitles.
Special VCD & SVCD Features
Playback Control (PBC)
PBC function allows you to enter the index menu which
is used to select a track after loading the VCD & SVCD
disc.
If you want to activate the function during the playback or
after pressing STOP twice,
1
Press MENU to set the PBC On.
Pay attention to the hint on the screen.
2
Use
¡1
or
2™
to select the page you like.
If the items of the index menus are numbered, press
the appropriate numeric buttons.
Press ENTER/OK.
3
Press RETURN to enter the index menu during the
playback.
Notes:
– The content of the index menu depends on the disc.
Please refer to the disc’s instructions for details.
– If the disc doesn’t include the PBC information, this
function will have no effect.
If you want to skip the index menu and playback
directly from the beginning,
1
Press MENU to switch off the function.
DVDDVD
VCDVCD
SVCDSVCD
DVDDVD
DVDDVD
DVDDVD
DVDDVD
DVDDVD
SVCDSVCDSVCD
Operation
11
English
Preview Function
Press SCAN to enter previewing menu.
Press
34
to highlight “TRACK DIGEST”, “DISC
INTERVAL” or “TRACK INTERVAL”.
Press ENTER/OK to open one option.
After you enter the menu of any digest type,
To quit preview function: Press
341
2
to highlight
EXIT and press ENTER/OK.
To return to the previewing menu for selecting the
other digest type: Press
341
2
to highlight MENU and
press ENTER/OK.
1
TRACK DIGEST
This function will minimize the picture of every track in
order to display every six of these tracks on the screen to
help you know the content of every track on the disc.
- To choose the desired track, press
341
2
to highlight
the second line and input your selected track number
next to “SELECT”.
Select the others from the current six by pressing the
¡1
or
2™
to open the previous or next page and press
ENTER/OK.
2
DISC INTERVAL
This function is used to divide a disc into six parts by
regular intervals and display them on one page to help
you preview the whole disc.
- To choose the desired track, press
341
2
to highlight
the second line and input your numerical selection next
to “SELECT” and press ENTER/OK.
3
TRACK INTERVAL
This function is used to divide a single track into six parts
by regular intervals and display them on one page to help
you preview the selected track.
- To choose the desired track, please press
341
2
to
highlight the second line and input your numerical
selection next to “SELECT” and press ENTER/OK.
VCDVCD
SVCDSVCD
TRACK DIGEST
SELECT DIGEST TYPE:
DISC INTERVAL
TRACK INTERVAL
TYPE : TRACK
EXIT
MENU NEXT
SELECT (01–17) : – –
TYPE : DISC INTERVAL
EXIT
MENU
SELECT (01–06) : – –
TYPE : TRACK 01 INTERVAL
EXIT
MENU
SELECT (01–06) : – –
Operation
12
This player can playback JPEG format pictures and MP3
files on a personally recorded CD-R/RW disc or
commercial CD, and is compatible with Kodak Picture
CD.
Playback pictures or songs one by one automatically.
Album and track selection.
Repeat (disc / album / track / picture).
Select any music or pictures from the disc to playback
them together.
Maximum files numbers in one folder is 500.
Maximum files Programmable is 100.
General Operation
If you choose WITH MENU in the Setup Menu (Please
refer to the MP3 & JPEG navigator below), the JPEG CD/
MP3 CD menu will be shown on the screen before
playback.
At any time during JPEG playback, press MENU to return
to the menu.
To open the selected folder, press ENTER/OK.
The menu shows six files or folders at a time. To move
to the next (or previous) page, press
2™
(or
¡1
).
MP3 & JPEG Navigator
To select a different playback method, follow the steps
below.
1
At STOP mode, press SETUP to open the setup menu.
2
Press
1
2
to highlight PREFERENCE icon.
3
Press
4
to open the PREFERENCE menu.
4
Press
34
to highlight the MP3/JPEG NAV menu.
5
Press
2
to enter the menu.
6
Press
34
to highlight the WITHOUT MENU or WITH
MENU item.
WITHOUT MENU: automatically playback all files in
according date sequence.
WITH MENU: playback files in the selected folder.
7
Press ENTER/OK to confirm your selection.
Play Mode
Auto Playback
If you choose WITHOUT MENU, the DVD player will
automatically play JPEG CD/MP3 CD in sequence when
it is loaded.
Repeat / Shuffle
When the JPEG CD/MP3 CD menu is shown on the
screen, Press REPEAT repeatedly, the button beside
PLAY MODE will display different option,
Repeat One: One file will be replayed time after time.
Repeat Folder: All files in this folder will be replayed
time after time.
Shuffle: All files in this folder will be played at random
without any repeat.
Folder: All files in this folder will be played.
If you press REPEAT during playback, the option will be
displayed on the screen accordingly.
During Shuffle mode, you can skip tracks by pressing
¡1
or
2™
.
00:00 00:00
1
001
002
003
004
005
006
JPEG & MP3 CD Playback
13
English
Special JPEG Features
Function Introduction
JPEG CD is a disc with a collection of JPEG format
pictures, and all extension filenames should end with
‘.JPG’. The CD can be recorded on any computer, and
pictures may be from digital camera or scanner. If the
customers prefer, they can make this CD become a
Digital Album.
You can choose any general function introduced in
General Operation, besides, you also can,
Display the thumbnails of 12 pictures.
Zoom the picture.
Rotate the picture.
Flip the picture vertically or horizontally.
Scan pictures by different effects.
Preview Function
This function shows the content of the current folder or
the whole disc.
1
Press STOP during playback of JPEG pictures. You will see
the thumbnails of 12 pictures on the screen.
2
Press
¡1
or
2™
to display the other pictures on the next
or the previous page.
3
Press
341
2
to highlight one of them and press ENTER/
OK to playback, or,
Move the cursor to highlight on the bottom of the
page to start playback from the first picture on the
current page.
4
Press MENU to go to the JPEG CD/MP3 CD menu.
Zoom picture
During playback, press ZOOM to display the picture with
different scales.
Press
341
2
to view the rest of the zoomed picture.
Playback with multi-angles
When displaying one picture on TV screen
Press
341
2
to get different effects.
3
: Flip the picture vertically.
4
: Flip the picture horizontally.
1
: rotate the picture anti-clockwise.
2
: rotate the picture clockwise.
Wipe Effect
Press ANGLE repeatedly to choose different wipe
effects.
Special MP3 Features
Function Introduction
“MP3” stands for “MPEG Audio Layer-3”. and is a part of
the MPEG standard. A CD can store up to 10 hours of
MP3 audio, which is nearly 10 times as much as an Audio
CD. Each song is recorded as a file. You can choose any
general function introduced in General Operation. You
can also choose different playback speeds.
JPEG and MP3 simultaneous playback
1
Firstly playback MP3 music according to the instructions
introduced in playback Selection.
2
Then select a picture to playback. Refer to the
instructions introduced in playback Selection.
Now the pictures will be played back in sequence
together with MP3 music.
3
To quit simultaneous playback, press MENU to return to
the JPEG CD/MP3 CD menu, then pictures will be
stopped. After that, press STOP, then MP3 music will be
stopped as well.
Note: In the function of JPEG and MP3 Simultaneous
Playback,
¡1
and
2™
are invalid for MP3.
JPEG & MP3 CD Playback
14
Basic Operation
1
Press SETUP in the STOP mode to enter the Setup
Menu.
2
Press
1
2
to enter the submenu or return to the previous
menu.
3
Press
34
to highlight the desired menu.
4
Press SETUP to quit the setup menu.
When you quit the setup menu, the settings will be
stored in the player’s memory even if the player is
switched to power off.
General Setup menu
Some settings need to be made in this menu. They are:
“DISC LOCK”, “PROGRAM”, “OSD LANGUAGE” and
“SCREEN SAVER”.
Follow the steps below:
1
Press SETUP to enter the setup menu.
2
Press
1
2
to choose the GENERAL SETUP icon .
DISC LOCK
When the disc is locked, the player will store its specific
code into the memory for future identification. For the
next playback, the DVD player will prompt you to enter
the password. Then, press ENTER/OK to load the disc.
1
Press
34
to highlight “DISC LOCK”.
2
Enter its submenu by pressing
2
.
Lock: Lock the disc being played.
Unlock: unlock the disc.
3
Press
1
to return to the General Setup Page.
PROGRAM (not for JPEG / MP3 CD)
1
Press
34
to choose “PROGRAM”.
2
Press
2
to move the cursor to the field of the submenu
to choose the item Input menu.
Input menu: Enter the Program item.
3
Press ENTER/OK to enter the program page.
Input your favorite track
1
Input valid track number by pressing the numeric buttons.
2
Press
341
2
to move the cursor to the next selected
position.
If the track number is more than ten, press
2™
to
open the next page and go on programing, or press
341
2
to highlight NEXT button, and then press ENTER/OK.
3
Repeat this steps to input another track number until the
whole program is completed.
Remove a track
1
Press
341
2
to move the cursor to the track you want
to remove.
2
Press ENTER/OK or PLAY to remove this track from the
program menu.
Playback tracks
When programing is completed,
1
Press
341
2
to move the cursor to the START button.
2
Press ENTER/OK.
DVD player will playback the selected tracks under
the programed sequence.
Quit the program playback
In the Program menu,
1
Press
341
2 to move the cursor to the EXIT button.
2 Press ENTER/OK to quit this menu.
Stop the program playback
During playback of the programmed tracks, press STOP.
Then after you press PLAY, the DVD player will resume
normal playback.
DISC LOCK
PROGRAM
OSD LANGUAGE
SCREEN SAVER
- - GENERAL SETUP PAGE - -
PROGRAM:TRACK(01-13)
EXIT START NEXT
1
2
3
4
5
7
8
9
10
_ _
02
01
05
_ _
6
03
_ _
_ _
_ _
_ _
Setup Menu
15
English
Repeat the program playback
During playback of the programmed tracks, press
REPEAT. The programed tracks can be played again.
Note: If you select Shuffle mode by pressing REPEAT several
times, the DVD player cancels program playback.
OSD LANGUAGE
This option is to select a language for information
displayed on TV screen.
1
Press
34
to highlight “OSD LANGUAGE” in the
General Setup menu.
2
Enter its submenu by pressing
2
.
3
Move the cursor by pressing
34
to highlight the selected
language.
4
Press ENTER/OK to confirm.
5
Press
1
to return to the General Setup Page.
SCREEN SAVER
This function is used to turn the screen saver on or off.
1
Press
34
to highlight “SCREEN SAVER” in the General
Setup menu.
2
Enter its submenu by pressing
2
.
3
Move the cursor by pressing
34
to highlight the selected
item.
On: In STOP or No DISC mode, if no actions are
performed within 5~6 minutes, the screen saver will be
activated.
Off: Screen saver is disabled.
4
Press ENTER/OK.
5
Press
1
to return to the General Setup Page.
Audio Setup menu
There are items included in Audio Setup Page such as
“SPEAKER SETUP”, “DIGITAL AUDIO SETUP”,
“EQUALIZER” and “3D”.
1
Press SETUP to enter the setup menu.
2
Press
1
2
to choose the AUDIO SETUP icon .
SPEAKER SETUP
This menu contains setup options for your analog audio
output, such as “DOWNMIX”, “DRC” (Dynamic Range
Compression) etc. which makes the setup system
reproduce high quality surround sound.
DOWNMIX
1
Press
34
to highlight the “DOWNMIX”.
2
Enter its submenu by pressing
2
.
3
Move the cursor by pressing
34
to highlight the selected
item.
LT/RT
This option should be used only if your DVD player
is connected to a Dolby Prologic decoder.
STEREO
This option will downmix Dolby Digital signals directly
into analogue stereo from L/R jacks.
VIRTUAL SURROUND
This option will reproduce the surround channels
virtually.
4
Press ENTER/OK.
5
Press
1
to return to the Audio Setup Page.
DRC (Dynamic Range Compression)
The DVD player will compress the dynamic range of its
sound output for late-night listening.
1
Press
34
to highlight “DRC”.
2
Enter its submenu by pressing
2
.
3
Move the cursor by pressing
34
to highlight the selected
item.
ON: Enable DRC.
OFF: Disable DRC.
4 Press ENTER/OK.
5 Press 1 to return to the Audio Setup Page.
- - AUDIO SETUP PAGE - -
SPEAKER SETUP
DIGITAL AUDIO SETUP
EQUALIZER
3D
Setup Menu
16
DIGITAL AUDIO SETUP
In this menu, you can set up the digital audio output signal
from the digital jacks, such as coaxial etc.
DIGITAL OUTPUT
1
Press
34
to highlight DIGITAL OUTPUT.
2
Enter its submenu by pressing
2
.
3
Press
34
to highlight the selected item.
ALL: Original digital signals output. In this mode, all
audio settings except MUTE are invalid.
PCM Only: If your receiver is PCM-compatible, or
your receiver can not decode MPEG-2, Dolby Digital, or
DTS audio, choose this option.
4
Press ENTER/OK.
5
Press
1
and return to the Audio Setup Page.
Note: If DIGITAL OUTPUT is set to “ALL”, all audio settings
except MUTE are invalid.
LPCM OUTPUT
In this menu, you can select PCM digital output between
48kHz and 96kHz.
1
Press
34
to highlight the “LPCM OUTPUT”.
2
Enter its submenu by pressing
2
.
3
Move the cursor by pressing
34
to highlight the selected
item.
48K: 96kHz (if available on disc) PCM data stream will
be converted to 48kHz.
96K: If the 96kHz disc is copy protected, the digital
output will be muted to comply with the standards.
4
Press ENTER/OK.
5
Press
1
to return to the Audio Setup Page.
EQUALIZER (Sound Mode)
The “EQUALIZER” allows you to select from various
preset modes that control the frequency bands of sound
to optimize certain musical styles.
It greatly enhances the excitement and enjoyment of your
favourite music.
1
Press
34
to highlight the “EQUALIZER”.
2
Enter its submenu “SOUND MODE” by pressing
2
.
3
Press
2
.
4
Move the cursor by pressing
34
to highlight the selected
item.
NONE: Play the disc under the original sound effect.
5
Press ENTER/OK.
6
Press
1
to return to the Audio Setup Page.
Note: The sound may be distorted if the selected sound
mode is incompatible with the disc contents.
In that case, select another sound mode or “NONE”.
3D (REVERB MODE)
The “3D” can simulate the echoes and frequency
response of some particular places so as to make you feel
like personally on the place.
1
Press
34
to highlight the “3D”.
2
Enter its submenu “REVERB MODE” by pressing
2
.
3
Press
2
.
4
Move the cursor by pressing
34
to highlight the selected
item.
OFF: Play the disc under the original sound effect.
5
Press ENTER/OK.
6
Press
1
to return to the Audio Setup Page.
Setup Menu
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186

Yamaha DV-SL100 El kitabı

Kategori
Dvd oynatıcılar
Tip
El kitabı