Yamaha CRX-550 El kitabı

Printed in Malaysia

WV39750

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

CD RECEIVER

AMPLI-TUNER CD

MCR-550

i

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou de

méthodes autres que ceux décrits ci-dessous, peuvent

entraîner une exposition à un rayonnement dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die Einstellung

bzw. die Ausführung von anderen als in dieser Anleitung

beschriebenen Vorgängen kann zu Gefährdung durch

gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande av

åtgärder på annat sätt än så som beskrivs häri kan resultera i

farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure non

specificati in questo manuale possono risultare in esposizione

a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos que

no se especifican enste manual pueden causar una exposición

peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of procedures

anders dan beschreven in dit document kan leiden tot

blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или произведение

настроек или выполнение процедур, не указанных в

данной инструкции, может отразиться на выделении

опасной радиации.

DANGER:

CAUTION:

AVOID DIRECT EXPOSURE TO THE BEAM

INVISIBLE LASER RADIATION WHEN OPEN

DO NOT STARE INTO BEAM

INVISIBLE LASER RADIATION WHEN OPEN

ii

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten

muutto saattaa altistaa vaaralliselle säteilylle tai muille

vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for

stråling.

Bemærk: Netafbryderen er sekundært indkoblet og ofbryder

ikke strømmen fra nettet. Den indbyggede netdel er derfor

tilsluttet til lysnettet så længe netstikket sidder i stikkontakten.

N

Observer: Nettbryteren er sekundert innkoplet. Den

innebygdenetdelen er derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för osynlig

laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Strömbrytaren är sekundärt kopplad och inte bryter

inte strömmen från nätet. Den inbyggda nätdelen är därför

ansluten till elnätet så länge stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1

ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja

roiskevedelle.

Huom. Toiminnanvalitsin on kytketty toisiopuolelle, eikä se

kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-osa on

kytkettynä sähköverkkoon aina silloin, kun pistoke on

pistorasiassa.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA

EJ STRÅLEN.

OBSERVERA

Apparaten kopplas inte bort från växelströmskällan (nätet) så

länge som den är ansluten till vägguttaget, även om själva

apparaten har stängts av.

ADVARSEL

Netspæendingen til dette apparat er IKKE afbrudt, sålæenge

netledningen siddr i en stikkontakt, som er t endt - også selvom

der or slukket på apparatets afbryder.

VAROITUS

Laitteen toisiopiiriin kytketty käyttökytkin ei irroita koko

laitetta verkosta.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED.

Make sure that neither core is connected to the earth

terminal of the three pin plug.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry,

clean place - away from direct sunlight, heat sources,

vibration, dust, moisture, and/or cold. For proper

ventilation, allow the following minimum clearances

around CRX-550.

Top: 20 cm (8 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit,

which may cause an electrical shock, fire, damage to this

unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e. vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set this unit to the

standby mode, and disconnect the AC power plug from

the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the power off, then leave this unit

alone for cooling.

20 Install this unit near the AC outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

22 Excessive sound pressure from earphones and

headphones can cause hearing loss.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc tray

and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as

it is connected to the wall outlet, even if this unit itself is turned off

by . This state is called the standby mode. In this state, this unit is

designed to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The laser component in this product is capable of emitting radiation

exceeding the limit for Class 1.

LASER

Type Semiconductor laser GaAs/GaAlAs

Wave length 780 nm

Output Power 10 mW

WARNING

DO NOT TOUCH THIS UNIT WHEN IT IS USED

CONTINUOUSLY AT HIGH VOLUME BECAUSE THE

BOTTOM OF THIS UNIT MAY BECOME HOT. IT MAY LEAD

TO INJURIES SUCH AS BURNS, ETC.

1 En

PREPARATION OPERATION

ADDITIONAL

INFORMATION

English

WHAT YOU CAN DO WITH THIS UNIT ......... 2

SUPPLIED ACCESSORIES ................................. 2

PLAYABLE DISCS AND FILE FORMAT......... 3

REMOTE CONTROL ........................................... 4

Installing the batteries in the remote control ............. 5

Using the remote control ........................................... 5

FRONT PANEL DISPLAY ................................... 6

FRONT PANEL AND BASIC OPERATION ..... 7

PREPARATIONS................................................... 8

Connecting speakers/external components/

antennas................................................................. 8

Other connection........................................................ 9

Connecting the power cable....................................... 9

LISTENING TO MUSIC..................................... 10

Playback operation................................................... 10

Operation for iPod ................................................... 11

Operation for CD/USB ............................................ 11

Switching the display............................................... 12

Playback sound........................................................ 12

LISTENING TO FM RADIO STATIONS ........ 13

Tuning to radio stations ........................................... 13

Presetting radio stations........................................... 13

Selecting preset radio stations (Preset tuning)......... 13

Displaying Radio Data System information............ 13

Using the TP (traffic program) data service ............ 14

CLOCK AND TIMER ......................................... 15

Using the clock ........................................................ 15

Using timer and sleep timer..................................... 15

USING USEFUL FUNCTIONS .......................... 16

Using option menu................................................... 16

TROUBLESHOOTING .......................................18

General..................................................................... 18

Radio reception........................................................ 19

iPod.......................................................................... 19

USB ......................................................................... 20

Disc playback .......................................................... 21

Remote control ........................................................ 21

HANDLING COMPACT DISCS ........................22

SPECIFICATIONS...............................................22

CONTENTS

PREPARATION

OPERATION

ADDITIONAL INFORMATION

■ About this manual

• This manual describes how to operate this unit using a remote control except when it is not available. Some of these

operations are also available using the front panel buttons.

• The symbol “☞” with page number(s) indicates the corresponding reference page(s).

• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

2 En

PREPARATION

Make sure you have all of the following items.

WHAT YOU CAN DO WITH THIS UNIT

Play back music on the iPod /Discs/ USB device/external device \ p. 10

This unit can play back music stored in your iPod, CDs and music stored in USB device. Also you can

connect external device and enjoy music from the device that you connected.

*Refer to p. 3 for the playable disc and file format

Receive FM Radio stations and Radio Data System information

(Europe model only)

\ p. 13

You can enjoy listening to FM radio stations with this unit. Also when the Radio Data System

broadcasting station is received, you can display Radio Data system information on the front panel of

this unit (Europe model only).

Enhance sound for Audio CDs by bit data expansion \ p. 12

You can listen to Audio CDs with clear sound.

Improved sound for compressed source by Music Enhancer \ p. 12

You can enjoy compressed music source (MP3 and WMA) with better sound quality.

Set the Clock and Timer \ p. 15

You can set the clock and choose to display it on the front panel display during standby mode. Also

you can set the timer to play back music from the selected input source.

Charging iPod and USB device \ p. 9

This unit can charge iPod and USB device during standby mode.

Boost bass sound by connecting a subwoofer \ p. 8

You can enjoy boost bass sound by connecting a subwoofer.

SUPPLIED ACCESSORIES

Remote control

Batteries (x 2)

(AAA, R03, UM-4)

Indoor FM antenna USB cap* Dock cover*

Keep the USB cap out of the reach of

children, so that it is not mistakenly

swallowed.

CAUTION

* The USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using.

When the USB cap and the Dock cover

are covered.

3 En

PREPARATION

English

■ Playable discs

Use compact discs bearing the marks below.

To play back an 8-cm (3 in) CD

Place it in the inner recessed area of the disc tray. Do not

put a normal (12-cm) CD on top of an 8-cm (3 in) CD.

■ Playable MP3 and WMA files

MP3

*

1

Variable bitrate is supported.

WMA

• Version 8

• Version 9 (Standard and variable bitrates are supported.

Professional and Lossless are not supported.)

*

2

Both constant and variable bitrates are supported.

• Playback for Data Disc starts in alphanumeric order of files.

• Playback for USB starts in order by date and time of creation.

• Copyright-protected WMA (DRM) files cannot be played back

by this unit.

• The disc must be ISO 9660 compatible.

• The maximum file and folder numbers are as follows.

*

3

The root is counted as one of the folders.

PLAYABLE DISCS AND FILE FORMAT

....

Compact discs (digital audio)

....

CD-R,CD-RW digital audio discs

• CD-R or CD-RW discs bearing one of

the following phrases.

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

• Finalized CD-R or CD-RW discs

This compact disc player may not be able to

play some CD-R/CD-RW discs or discs on

which recording was not made correctly.

....

CD-TEXT discs

To prevent a malfunction of this unit:

• Do not use any nonstandard shaped

disc (heart, etc.) available on the

market because it might damage the

unit.

• Do not use a disc with tape, stickers, or paste on it. If

you use such a disc, the disc may get stuck in the

unit, or damage to the unit may result.

Note: Do not use any lens cleaners as they may be a

cause of malfunction.

Note

Format

Bitrate

(kbps)

Sampling

frequency

(kHz)

MPEG 1 Audio Layer-3

32-320

*1

32/44.1/48

MPEG 2 Audio Layer-3, 2

8-160

*1

16/22.05/24

Profile

Bitrate

(kbps)

Sampling

frequency

(kHz)

High Profile

32-320

*2

32/44.1/48

Mid Profile

16-32 22.05

Notes

Data Disc USB

Maximum total number of file

and folder

*3

512 9,999

Maximum folder number

*3

255 255

Maximum file number per

folder

511 255

4 En

REMOTE CONTROL

1 Infrared signal transmitter (☞ P. 5)

2 : Open and close tray

3 TIMER (☞ P. 15)

4 iPod Control buttons (☞ P. 11)

Used to operate your iPod

/ : Scroll buttons

MENU: Returns to the upper level in the iPod menu

ENTER: Select group/start playback

: Skip forward/press and hold to fast forward

: Skip backward/press and hold to fast backward

: Starts or pauses playback

SHUFFLE: Selects the shuffle play mode

REPEAT: Selects the repeat play mode

5 Input select buttons (☞ P. 10, 13)

Select the input source.

6 FM control buttons

TP: Enters TP (Traffic Program) data service receiving mode (☞ P. 14).

MEMORY: Starts preset tuning and stores preset station (☞ P. 13).

MONO: Sets FM Broadcasting receiving mode to monaural mode (☞ P. 13).

PRESET u / d: Selects preset station (☞ P. 13).

TUNING / : Press to start manual tuning. Press and hold to start

automatic tuning (☞ P. 13).

7 DIMMER

Changes brightness of the front panel. Choose brightness from normal (bright),

mid dim, or dim by pressing this button repeatedly.

8 DISPLAY (☞ P. 13)

Switches the information shown on the front panel.

9 Option control buttons (☞ P. 16)

OPTION: Enters option menu mode.

////ENTER: For selecting and confirming an item.

0 CD/USB control buttons (☞ P. 11)

Controls CD/USB playback

: Stops playback

: Pauses playback

: Starts playback

/ : Rewind/fast-forward music

/ : Skips to the beginning of current track or next track

SHUFFLE: Selects the shuffle play mode

REPEAT: Selects the repeat play mode

FOLDER / : Skips to the first file of selected folder for an MP3 or

WMA recorded on disc/USB device.

A N

umeric buttons (☞ P. 11)

Input numbers.

Press ENTER to confirm the entry.

Press CLEAR to clear the entry.

B CLOCK (☞ P. 15)

C (on/standby)

D SLEEP (☞ P. 15)

E Volume control buttons

Controls the volume.

Press MUTE to turn off the sound. Press again to resume the volume.

C

D

E

B

1

2

3

4

5

8

0

A

6

7

9

d

REMOTE CONTROL

5 En

PREPARATION

English

■ Notes on batteries

• Change both batteries when the operation range of the remote

control decreases.

• Use AAA, R03, UM-4 batteries.

• Make sure that the polarities are correct. See the illustration

inside the battery compartment.

• Remove the batteries if the remote control is not to be used for

an extended period of time.

• Do not use old batteries together with new ones.

• Do not use different types of batteries (such as alkaline and

manganese batteries) together. Read the packaging carefully as

these different types of batteries may have the same shape and

color.

• If the batteries have leaked, dispose of them immediately.

Avoid touching the leaked material or letting it come into

contact with clothing, etc. Clean the battery compartment

thoroughly before installing new batteries.

• Do not throw away batteries with general house waste; dispose

of them correctly in accordance with your local regulations.

The remote control transmits a directional infrared beam.

Be sure to aim the remote control directly at the remote

control sensor on the front panel of the unit during

operation.

• The area between the remote control and the unit must be clear

of large obstacles.

• Do not spill water or other liquids on the remote control.

• Do not drop the remote control.

• Do not leave or store the remote control in the following types

of conditions:

– high humidity, such as near a bath

– high temperature, such as near a heater or a stove

– extremely low temperatures

– dusty places.

• Do not expose the remote control sensor to strong lighting, in

particular, an inverter type fluorescent lamp; otherwise, the

remote control may not work properly. If necessary, position

the system away from direct lighting.

Installing the batteries in the

remote control

1

3

2

Using the remote control

Notes

30˚ 30˚

Within 6 m

(20 feet)

6 En

1 SLEEP indicator

Lights up when the sleep timer is on (☞ P. 15).

2 PRESET indicator

Lights up when you preset radio stations (☞ P. 13).

3 STEREO indicator

Lights up when this unit is receiving a strong signal from an

FM stereo broadcast.

4 AUTO indicator

Lights up when this unit is in the Automatic Tuning mode

(☞ P. 13).

5 SHUFFLE indicator

Lights up when you set your iPod/CD/USB to shuffle play

(☞ P. 11).

6 REPEAT indicator

Lights up when you set your iPod/CD/USB to repeat play

(☞ P. 11, 12).

7 Radio Data System indicators

The name of the Radio Data System data offered by the

currently received Radio Data System station lights up

(☞ P. 13).

8 MUTE indicator

Lights up when the sound is muted.

9 Multi information display

Shows the various information such as the tuning frequency.

0 TUNED indicator

Lights up when this unit is tuned into a station (☞ P. 13).

A MEMORY indicator

Flashes when searching for a radio station by automatic

preset tuning. Lights up when you preset radio stations

automatically or manually (☞ P. 13).

B Multi information indicator

Indicates the music information currently displayed on Multi

information display (☞ P. 12).

C Operation indicators

Shows operable option control buttons for a currently

selected OPTION item.

D TP indicator

Lights up when this unit is receiving a Radio Data System

station which contains the TP (traffic program) data service

(☞ P. 14).

E TIMER indicator

Lights up when the timer is on (☞ P. 15).

FRONT PANEL DISPLAY

GENRES

SONGS

ALBUMS

ARTISTSPLAYLISTS

MEMORY

TUNED

SLEEP

STEREO

AUTO

SHUFFLE

REPEAT

PS

PTY RT CT

MUTE

PRESET

7 En

OPERATION

English

OPERATION

y

• This unit has an automatic standby function, which will automatically switch the unit to standby mode if the unit is left turned on for

1 hour without playback or any other operation being performed. This function is not available when the source is set to FM/AUX1/

AUX2.

FRONT PANEL AND BASIC OPERATION

iPod dock

(on/standby):

Unit on/standby

The indicator lights up as

follows:

Brightly lit: Power is on

Dimly lit: Standby mode

When iPod/USB device is

charged or the clock is displayed

on the front panel during the

standby mode, the indicator

lights up brightly.

Note

:

Disc tray open/close

:

Play/pause playback

:

Stop playback

INPUT:

Selects an input source.

VOLUME

USB port:

☞ P. 9, 10

PHONES:

Connecting headphones

No sound is output from the speakers

when headphones are connected.

Disc tray

/

:

Skip backward and forward/press

and hold to rewind and fast-forward

PRESET < >:

Selects preset station

Front panel

display:

☞ P. 6

Down Up

8 En

Make sure you read the following procedure and note carefully before connecting the system. For information on the

speakers (NS-BP200), refer to the owner’s manual supplied with it.

Connecting the system

1 Connect the speaker terminals (L) of the unit to the speaker terminals of the left speaker and the speaker terminals (R)

of the unit to the speaker terminals of the right speaker using the speaker cables supplied with the speaker set (NS-

BP200).

2 Connect the supplied FM antenna to the FM jack.

• Do not connect this unit or other components to the main power until all connections between components are complete.

• Do not let the bare speaker wires touch each other or any metal part of the unit. This could damage the unit and/or the speakers.

• All connections must be correct: L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. If the connections are faulty, no sound will be

heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lack bass. Also,

refer to the owner’s manual for each of your components.

• When connecting speakers other than NS-BP200, use speakers having more than 6Ω impedance.

• If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use

commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.

PREPARATIONS

Connecting speakers/external components/antennas

CAUTION

Notes

DVD player etc.

Subwoofer

Right speaker

(NS-BP200)

Left speaker

(NS-BP200)

CD Receiver (CRX-550)

(Europe model)

Portable

player

RCA stereo

cable

3.5mm stereo

mini plug cable

Be sure to remove insulation from

the end of each speaker cable.

PREPARATIONS

9 En

OPERATION

English

■ Stationing iPod

Station or remove your iPod whenever you want.

y

Your iPod is automatically charged when your iPod is set in the

iPod dock even if the unit is in standby mode.

This unit is compatible with iPod (5th generation), iPod classic,

iPod nano and iPod touch.

• To secure the connection, attach a compatible Dock

Adapter supplied with the iPod or an iPod Universal Dock

Adapter (sold separately), and remove the protective case

covering your iPod.

• If you do not use an adapter or if the adapter is not

compatible, the connection could be loose or poor, which

could cause damage or malfunctions.

■ Connecting USB

Connect or remove your USB device whenever you want.

y

USB device is automatically charged when it is connected to the

unit, even if the unit is in standby mode.

• This unit supports USB mass storage class devices (e.g., flash

memories or portable audio players) using FAT16 or FAT32

format.

• Do not connect devices other than USB mass storage class

devices (such as USB chargers or USB hubs), PCs, card

readers, an external HDD, etc.

After you made all connections, connect the power cables

of this unit.

Other connection

Note

Notes

Dock Adapter

iPod dock

Connecting the power cable

To an AC wall

outlet

10 En

Follow the procedures below to play back music.

*

1

Some features may not be available depending on the model or the software version of your iPod.

*

2

· Some devices may not work properly even if they meet the requirements.

· Playability of and power supply to all kind of USB devices are not guaranteed.

· The reading time may exceed 30 seconds depending on the number of files/folders.

· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.

As a precaution, it is recommended that the files are made backup copies.

LISTENING TO MUSIC

Playback operation

Set the source

Switch the

input

Select music and start playback

iPod

*1

CD

USB

*2

AUX1

AUX2

1

2

3

☞ P. 9

Dock

Adapter

☞ P. 9

To AUX1 To AUX2

For operation, refer to the instruction

manuals supplied with external components

such as DVD player and portable player.

LISTENING TO MUSIC

11 En

OPERATION

English

Some features may not be compatible depending on the model or

the software version of your iPod.

■ Control playback

/ : Scroll buttons

MENU: Returns to the upper level in the iPod menu

ENTER: Select group/start playback

: Skip forward/press and hold to fast-forward

: Skip backward/press and hold to rewind

: Starts or pauses playback

• For iPod (5th generation) and iPod nano (1st generation), you

can only operate the iPod menu using the front panel display.

• There are some characters that cannot be displayed in the front

panel display of this unit.

■ Shuffle play

You can play back in random sequence.

*

1

You cannot set ALBUMS when you use an iPod touch.

■ Repeat play

You can play back repeatedly.

■ Control playback

: Stop

: Pause

: Play

: Rewind

: Fast forward

: Skip backward

: Skip forward

FOLDER / : Skip to the first file in the previous/next

folder for MP3 or WMA.

*

* If you press these buttons, the folder name is displayed on the

front panel display for a certain period.

y

You can also use the Numeric buttons to enter the number of

the song directly. To clear the entry, press CLEAR.

• Playback for Data Disc starts in alphanumeric order of files.

• Playback for USB starts in order by date and time of creation.

■ Shuffle play

You can play back in random sequence.

*

2

If the audio format of the selected music source is MP3/

WMA, you can also select FOLDER.

Operation for iPod

Note

Notes

1 2

During playback

iPod menu

Press repeatedly.

Operation for CD/USB

Notes

Press repeatedly.

1 2

During playback

Press repeatedly.

LISTENING TO MUSIC

12 En

■ Repeat play

You can play back repeatedly.

*

3

If the audio format of the selected music source is MP3/

WMA, you can also select FOLDER.

You can switch the playback information shown on the

front panel display. Some special characters may not be

shown properly.

For iPod

Song number and elapsed time (default setting)

↓

Song number and remaining time

↓

Song name

↓

Artist name

↓

Album name

↓

Back to the default setting

This function is available for iPod (5th generation), iPod classic,

iPod nano, and iPod touch. However, even with these models,

this function may not be available depending on the software

version of your iPod.

For CD/USB

Track/file number and elapsed time of the current

song (default setting)

↓

Track number and remaining time of the current

song

*4

↓

Total time of the disc

*4

↓

Remaining time of the disc

*4

↓

File name

*5

↓

Track name

*6

↓

Artist name

*6

↓

Album name

*6

↓

Back to the default setting

*

4

Only for Audio CDs

*

5

Only for MP3/WMA files

*

6

Only when the selected track has information

This unit has built-in sound program which will

automatically adjusts music source to provide enjoyable

sound quality.

■ Bit data expansion

Bit data expansion increases CD 16-bit data to 24 bits,

achieving a more natural and detailed sound.

This function is only available for Audio CDs.

■ Music Enhancer

Music Enhancer feature enhances the sound for

compressed music by regenerating musical elements that

are lost through compression.

This function is not available for Audio CDs and audio input

from external device connected to AUX1.

Switching the display

Note

Press repeatedly.

1 2

During playback

Playback sound

Note

13 En

OPERATION

English

y

If the signal received from the station you want to select is weak,

you can also tune into radio stations manually by pressing

TUNING / repeatedly.

When receiving a stereo broadcasting station, you can switch

between stereo and monaural by pressing MONO.

You can store your favorite FM stations with the preset

function.

■ Automatic preset tuning

When you perform the automatic preset, all stored stations are

cleared and the new stations are stored.

■ Manual preset tuning

y

• You can preset up to 30 FM stations.

• To cancel the manual preset while choosing a preset number,

press MEMORY again.

• You can delete a preset station by pressing OPTION → S/T

→ ENTER to select PRESET DELETE.

PS (Program Service)

↓

PTY (Program Type)

↓

RT (Radio Text)

↓

CT (Clock Time)

↓

Frequency

↓

Back to the PS

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text)

information uses a lot of bandwidth, so it may be less available

compared to other types of information.

LISTENING TO FM RADIO STATIONS

Tuning to radio stations

Note

Presetting radio stations

Note

Press TUNER. Press and hold.

Automatic tuning starts.

1 2

d

Press and hold

MEMORY for more than

2 seconds in FM mode.

Start the automatic preset.

1 2

Tune into a favorite

radio station.

Press MEMORY.

Select the preset

number you want to

store to.

Complete the manual

preset.

1 2

3 4

Selecting preset radio stations

(Preset tuning)

Displaying Radio Data System

information

Note

Select the preset radio station

in FM mode.

1 2

Press repeatedly.

While listening

LISTENING TO FM RADIO STATIONS

14 En

Use this feature to receive the TP (traffic program) data

service of the Radio Data System station network.

y

• “TP Search” flashes on the front panel display and the search

starts.

The TP indicator on the unit flashes during search.

• When the traffic program is received, the TP indicator stays on

and the search stops.

If you press TP again, the search starts again.

• If the unit fails to receive the traffic program, the TP indicator

turns off and “Not Found” appears on the display. The unit

returns to its previous state.

• To cancel the search, press TP during search.

Using the TP (traffic program) data

service

1 2

Press TP.

While listening

15 En

OPERATION

English

To set the clock, press and hold CLOCK or press

OPTION to enter CLOCK SET of the option menu.

As for the setting, refer to “Using option menu” on

page 16.

Once you set the clock, you can display the clock on the

front panel display.

When you press CLOCK while the power is on, the clock

is displayed on the front panel display for a few seconds.

When you press CLOCK during standby mode, you can

select whether to display the clock on the front panel

display or not.

• This unit supports 24-hour clock display.

• The clock setting will be lost if you disconnect the power cable

from the wall outlet for several minutes.

■ Using the timer

The timer sets the unit to play back music at the time you

set.

To set the timer, press and hold TIMER or press OPTION

to enter TIMER SET of the option menu.

As for the setting, refer to “Using option menu” on

page 16.

To use the timer, set the appropriate input source securely

and set the timer in the option menu in advance (☞ P. 17).

TIMER OFF: To set the timer off.

TIMER ONCE: To set the timer once.

TIMER EVERY: To set the timer everyday at the same

time.

When you switch the timer set to TIMER EVERY or

TIMER ONCE, the TIMER indicator lights up on the

front panel display.

• The clock has to be set in advance.

• When the timer is set, the TIMER indicator lights up on the

front panel display. While the power is on, the TIMER indicator

flashes as the set time of the timer becomes closer.

y

• The settings set in timer settings are retained.

■ Using sleep timer

The sleep timer sets the unit to the standby mode after the

specified time elapses.

The SLEEP indicator lights up on the front panel display.

CLOCK AND TIMER

Using the clock

Notes

Using timer and sleep timer

Press CLOCK.

Press repeatedly.

Notes

Press repeatedly.

16 En

The option menu appears on the front panel display by pressing OPTION. You can set various useful functions with

option menu.

*

1

This function is available only for Europe, U.K. and Australia models.

*

2

When there are some parameters to set, repeat steps 3 and 4. You can go back to a previous parameter by pressing .

*

3

To set additional items, repeat steps 2 to 5.

y

To cancel the setting during the operation, press OPTION.

■ Setting tone/balance

TREBLE

*4

: Adjusts the high frequency response.

BASS

*4

: Adjusts the low frequency response.

BALANCE: Adjusts the volume level of each left and right speaker channel.

*

4

Also effective when you are using headphones.

■ Adjusting the clock

AUTO CLOCK: Automatic adjustment function is available for Europe, U.K. and Australia models only. To apply for

this function, set AUTO CLOCK to ON.

CLOCK SET: To set hour and minute, repeat steps 3 and 4 on page 16.

y

• You can enter CLOCK SET directly by pressing and holding CLOCK when the unit is on.

• When setting the clock, you can also use the Numeric buttons to enter the hour and minute. To confirm the entry, press ENTER.

To clear the entry, press CLEAR.

• The current time appears on the front panel display for a certain period by pressing CLOCK when the unit is on.

The time setting will be lost if you disconnect the power cable from the wall outlet for several minutes.

USING USEFUL FUNCTIONS

Using option menu

Option menu Parameter or control range Reference page

PRESET DELETE (Displays only when the input source is set to FM.) 13

TREBLE –10 dB to +10 dB below

BASS –10 dB to +10 dB below

BALANCE L+5 - CENTER - R+5 below

AUTO CLOCK*

1

ON/OFF below

CLOCK SET Hour, minute below

TIMER SET

Time (hour, minute), sound (source, track or preset number), volume,

timer on (every/once)/off

17

Press OPTION. Select desired

option menu.

Confirm with

ENTER.

Change the settings. Complete the

setting.*

3

1 2 3 4 5

Repeat*

2

Exit option

menu.

6

Note

Sayfa yükleniyor ...

Yamaha CRX-550 El kitabı

Bu kılavuz için de uygundur

Yamaha CRX-550 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler