Yamaha AW2400 Kullanım kılavuzu

EN

Owner’s Manual

AW2400 Owner’s Manual

2

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B)

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS

UNIT!

This product, when installed as indicated in the instruc-

tions contained in this manual, meets FCC requirements.

Modiﬁcations not expressly approved by Yamaha may

void your authority, granted by the FCC, to use the prod-

uct.

2. IMPORTANT: When connecting this product to acces-

sories and/or another product use only high quality

shielded cables. Cable/s supplied with this product MUST

be used. Follow all installation instructions. Failure to fol-

low instructions could void your FCC authorization to use

this product in the USA.

3. NOTE: This product has been tested and found to com-

ply with the requirements listed in FCC Regulations, Part

15 for Class “B” digital devices. Compliance with these

requirements provides a reasonable level of assurance

that your use of this product in a residential environment

will not result in harmful interference with other electronic

devices. This equipment generates/uses radio frequen-

cies and, if not installed and used according to the

instructions found in the users manual, may cause inter-

ference harmful to the operation of other electronic

devices. Compliance with FCC regulations does not guar-

antee that interference will not occur in all installations. If

this product is found to be the source of interference,

which can be determined by turning the unit “OFF” and

“ON”, please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line ﬁlter/s.

In the case of radio or TV interference, relocate/reorient

the antenna. If the antenna lead-in is 300 ohm ribbon

lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to dis-

tribute this type of product. If you can not locate the

appropriate retailer, please contact Yamaha Corporation

of America, Electronic Service Division, 6600 Orangetho-

rpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products dis-

tributed by Yamaha Corporation of America or its subsid-

iaries.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011

Type of Equipment : Professional Audio Workstation

Model Name : AW2400

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interfer-

ence that may cause undesired operation.

See user manual instructions if interference to radio reception is sus-

pected.

* This applies only to products distributed by

YAMAHA CORPORATION OF AMERICA.

(FCC DoC)

IMPORTANT NOTICE FOR THE UNITED KINGDOM

Connecting the Plug and Cord

WARNING: THIS APPARATUS MUST BE EARTHED

IMPORTANT. The wires in this mains lead are coloured in accordance

with the following code:

GREEN-AND-YELLOW : EARTH

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead of this apparatus may not

correspond with the coloured markings identifying the terminals in your

plug proceed as follows:

The wire which is coloured GREEN-and-YELLOW must be connected to

the terminal in the plug which is marked by the letter E or by the safety

earth symbol or colored GREEN or GREEN-and-YELLOW.

The wire which is coloured BLUE must be connected to the terminal

which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd. (3 wires)

3

AW2400 Owner’s Manual

The above warning is located on the rear of the unit.

Explanation of Graphical Symbols

The lightning ﬂash with arrowhead symbol

within an equilateral triangle is intended to

alert the user to the presence of

uninsulated “dangerous voltage” within

the product’s enclosure that may be of

sufﬁcient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an

equilateral triangle is intended to alert the

user to the presence of important operating

and maintenance (servicing) instructions

in the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampliﬁers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. If

the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or

pinched particularly at plugs, convenience

receptacles, and the point where they exit from the

apparatus.

11 Only use attachments/accessories speciﬁed by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

speciﬁed by the manufacturer,

or sold with the apparatus.

When a cart is used, use

caution when moving the cart/

apparatus combination to

avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 Refer all servicing to qualiﬁed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has

been exposed to rain or moisture, does not operate

normally, or has been dropped.

(98-6500)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.

This product contains a high intensity lamp that contains a small amount of mercury.

Disposal of this material may be regulated due to environmental considerations.

For disposal information in the United States, refer to the Electronic Industries Alliance web site:

www.eiae.org

(mercury)

AW2400 Owner’s Manual

4

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not

limited to, the following:

• Only use the voltage speciﬁed as correct for the device. The required

voltage is printed on the name plate of the device.

• Use only the included power cord.

• Do not place the power cord near heat sources such as heaters or

radiators, and do not excessively bend or otherwise damage the cord,

place heavy objects on it, or place it in a position where anyone could

walk on, trip over, or roll anything over it.

• Be sure to connect to an appropriate outlet with a protective grounding

connection. Improper grounding can result in electrical shock.

• Do not open the device or attempt to disassemble the internal parts or

modify them in any way. The device contains no user-serviceable parts. If

it should appear to be malfunctioning, discontinue use immediately and

have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet

conditions, or place containers on it containing liquids which might spill

into any openings.

• Never insert or remove an electric plug with wet hands.

• If the power cord or plug becomes frayed or damaged, or if there is a

sudden loss of sound during use of the device, or if any unusual smells

or smoke should appear to be caused by it, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

• If this device should be dropped or damaged, immediately turn off the

power switch, disconnect the electric plug from the outlet, and have the

device inspected by qualiﬁed Yamaha service personnel.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the device or other property. These precautions include, but are not limited to, the following:

• Remove the electric plug from the outlet when the device is not to be

used for extended periods of time, or during electrical storms.

• When removing the electric plug from the device or an outlet, always

hold the plug itself and not the cord. Pulling by the cord can damage it.

• Before moving the device, remove all connected cables.

• When setting up the product, make sure that the AC outlet you are using

is easily accessible. If some trouble or malfunction occurs, immediately

turn off the power switch and disconnect the plug from the outlet. Even

when the power switch is turned off, electricity is still ﬂowing to the

product at the minimum level. When you are not using the product for a

long time, make sure to unplug the power cord from the wall AC outlet.

•Avoid setting all equalizer controls and faders to their maximum.

Depending on the condition of the connected devices, doing so may

cause feedback and may damage the speakers.

• Do not expose the device to excessive dust or vibrations, or extreme cold

or heat (such as in direct sunlight, near a heater, or in a car during the

day) to prevent the possibility of panel disﬁguration or damage to the

internal components.

• Do not place the device in an unstable position where it might

accidentally fall over.

• The plastic side panels do not provide a secure grip, and should not be

used as handles when moving or transporting the unit. Carrying the unit

by the plastic side panels can result in the unit being dropped, which

could damage the unit and/or cause personal injury.

• Do not block the vents. This device has ventilation holes at the top/front/

rear to prevent the internal temperature from becoming too high. In

particular, do not place the device on its side or upside down. Inadequate

ventilation can result in overheating, possibly causing damage to the

device(s), or even ﬁre.

• Do not use the device in the vicinity of a TV, radio, stereo equipment,

mobile phone, or other electric devices. Doing so may result in noise,

both in the device itself and in the TV or radio next to it.

PRECAUTIONS

Power supply/Power cord

Do not open

Water warning

If you notice any abnormality

Power supply/Power cord

Location

(5)-4 1/2

5

AW2400 Owner’s Manual

• Before connecting the device to other devices, turn off the power for all

devices. Before turning the power on or off for all devices, set all volume

levels to minimum.

• Be sure to connect to a properly grounded power source. A ground screw

is provided on the rear panel of this device for maximum safety and

shock prevention. If the mains outlet is not grounded, be sure to connect

the ground screw to a conﬁrmed ground point before plugging the device

into the mains. Improper grounding can result in electrical shock.

• When turning on the AC power in your audio system, always turn on the

power ampliﬁer LAST, to avoid speaker damage. When turning the power

off, the power ampliﬁer should be turned off FIRST for the same reason.

• Do not insert your ﬁngers or hands in any gaps or openings on the

device (vents, disc slots, etc.).

•Avoid inserting or dropping foreign objects (paper, plastic, metal, etc.)

into any gaps or openings on the device (vents, disc slots, etc.) If this

happens, turn off the power immediately and unplug the power cord from

the AC outlet. Then have the device inspected by qualiﬁed Yamaha

service personnel.

• Do not use headphones for a long period of time at a high or

uncomfortable volume level, since this can cause permanent hearing

loss. If you experience any hearing loss or ringing in the ears, consult a

physician.

• Do not rest your weight on the device or place heavy objects on it, and

avoid use excessive force on the buttons, switches or connectors.

Always turn the power off when the device is not in use.

The performance of components with moving contacts, such as switches, volume controls, and connectors, deteriorates over time. Consult qualiﬁed Yamaha

service personnel about replacing defective components.

Connections

Handling caution

XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

Insert TRS phone jacks are wired as follows: sleeve: ground, tip: send, and ring: return.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device, or data that is lost or destroyed.

(5)-4 2/2

AW2400 Owner’s Manual

6

This product utilizes a laser.

Use of control, adjustment or performance of procedures other than those speciﬁed herein may result in haz-

ardous radiation exposure.

Do not open covers and do not repair yourself. Refer servicing to qualiﬁed personnel.

The label shown below is located on the rear of this product.

The label shown below is located on the top of the internal CD-RW drive.

Please observe the following points when handling the disc.

Failure to do so may cause problems such as the recorded data being lost, the drive to malfunction, or the

printed label to become blurred.

• Do not place the disc in locations of direct sunlight, high temperature, or high humidity.

• Do not touch the recording surface of the disc.

Hold the disc at the edges.

• Gently wipe dust or dirt off of the recording surface of the disc.

Use an air duster or cleaner to remove dust. Vigorously rubbing the surface of the disc with a dry cloth may

scratch the disc.

• If the disc surface needs cleaning, wipe gently from the center to the outside of the disc with a soft damp

cloth, then gently wipe off remaining moisture in the same way with a clean dry cloth.

• Do not write on the disc or afﬁx labels to it.

• Do not wipe the disc with chemicals or detergents.

• Do not bend or drop the disc.

Caution for Laser

Laser properties of the Drive

Laser Class : Class 1 (HHS and IEC 825-1)

Wavelength : for CD 784 nm

for DVD 662 nm

Handling the CD-R/RW media

CLASS 1 LASER PRODUCT

CAUTION

CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.

ATTENTION

CLASSE 3B RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D’OUVERTURE.

EXPOSITION DANGEREUSE AU FAISCEAU.

VORSICHT

KLASSE 3B SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GEÖFFNET.

NICHT DEM STRAHL AUSSETZEN.

ADVARSEL

KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING. UNDGÅ UDS/ETTELSE FOR STRÅLING.

ADVARSEL

KLASSE 3B SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES. UNNGÅ EKSPONERING FOR STRÅLEN.

VARNING

KLASS 3B SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO!

KURSSI 3B NÄKYVÄ JA NÄKYMÄTÖN AVATTAESSA OLET ALTTIINA LASERSÄTEILYLLE, ÄLÄ KATSO SÄTEESEN.

CAUTION: CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.

7

AW2400 Owner’s Manual

• During some hard disk operations a small amount of vibration might be felt at the control panel and you

might hear some mechanical noises. This is normal.

• Do not subject the unit to strong physical shock. Excessive physical shock can damage the internal hard

disk.

•Always turn the power off when moving the unit from one location to another. Data on the internal hard disk

can be lost or corrupted if the unit is moved while the power is on.

Copyright and other intellectual property laws in various countries permit reproduction of copyrighted materi-

als under certain requirements. The observance of applicable laws for use of this product, however, is your

responsibility. Yamaha disclaims any liability for violation of such laws in association with the use of this

product.

Although this product is designed for original music production, it can be utilized to make reproduction of

copyrighted music and other sound products. While certain reproduction and use of reproduced materials are

permitted under applicable laws, such reproduction and use without license may constitute copyright infringe-

ment and other violation of laws. Since violation of such laws can have serious consequences, you may wish

to consult a legal expert about your planned use of this product.

This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or

with respect to which it has license to use others’ copyrights. Such copyrighted materials include, without lim-

itation, all computer software, styles ﬁles, MIDI ﬁles, WAVE data and sound recordings. Any unauthorized use

of such programs and contents outside of personal use is not permitted under relevant laws. Any violation of

copyright has legal consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES.

Internal Hard Disk Precautions

Copyright Notice

The illustrations and LCD screens as shown in this owner’s manual are for instructional purposes only, and may

appear somewhat different from those on your instrument.

AW2400 Owner’s Manual

8

Contents

1. Before you start 11

Introduction................................................................. 11

Remember to back up your data ................................ 11

About the built-in CD-RW drive ..................................12

Using the CD-RW drive .............................................. 12

Installing an optional card........................................... 13

2. Introducing the AW2400 15

Features of the AW2400 ............................................15

AW2400 terminology .................................................. 17

Recorder section....................................................17

Mixer section..........................................................18

Overall.................................................................... 19

Parts of the AW2400 and what they do...................... 20

Top panel ...............................................................20

Rear panel ............................................................. 28

Front panel.............................................................29

Basic operation of the AW2400.................................. 30

Viewing the display ................................................30

Accessing a screen/page.......................................31

Switching a button on/off........................................ 31

Editing a value in the display ................................. 31

Using Additional Function Buttons .........................31

Entering text...........................................................32

Switching Mixing Layers ........................................ 33

Using the Selected Channel section ......................33

3. Connection and Setup 37

Connection .................................................................37

Turning the power on/off ............................................38

Adjusting the input level .............................................39

4. Listening to the demo song 41

Loading the demo song.............................................. 41

Playing the demo song............................................... 42

5. Recording to a sound clip 43

Recording a sound clip............................................... 43

Playing a sound clip ...................................................45

6. Track recording 47

Creating a new song ..................................................47

Direct recording and Mixed recording.........................49

Assigning input signals to tracks

(Direct recording)...............................................51

Assigning input signals to tracks

(Mixed recording) ..............................................54

Recording on a track...................................................56

Saving the current song..............................................57

Pairing channels .........................................................58

Applying EQ To an Input Signal..................................60

Applying Compression to an Input Signal...................61

Handy Recording Functions .......................................62

Using the Metronome .............................................62

Switching virtual tracks...........................................63

Using the Undo List ................................................64

7. Overdubbing 65

About overdubbing......................................................65

Assigning the input signal to a track ...........................66

Setting the mix balance and pan ................................67

Overdubbing ...............................................................68

Punch-in/out................................................................69

Manual punch-in/out...............................................69

Auto punch-in/out ...................................................70

8. Mixdown and bounce operations 73

About mixdown and bouncing.....................................73

Mixdown procedure ....................................................75

Playing back the stereo track......................................78

Bounce (ping-pong) recording procedure ...................79

Convenient functions for mixdown/bounce .................82

Fader Group assignments......................................82

Mute Group assignments .......................................83

Using the Solo function ..........................................84

9. Transport/Locate Operation 87

The Transport Section Keys .......................................87

Move To a Specified Location ....................................87

Using the locator.........................................................88

Using markers.............................................................90

Adjusting the position of a locate point or marker.......91

Adjusting the position of a locate point...................91

Adjusting the position of a marker ..........................92

Erasing a locate point or marker.................................93

Repeat playback of a specific region

(the A-B Repeat function) ...........................................93

Finding a location while monitoring the sound

(the Nudge function) ...................................................94

Finding a location while viewing the waveform...........95

10. Meters 97

Level Meter Types ......................................................97

9

AW2400 Owner’s Manual

Contents

11. Patching and signal flow 99

Input signal patching ..................................................99

Patching for Direct Recording ................................99

Patching for Mixed Recording..............................102

Output signal patching.............................................. 104

12. Channel Operation 105

Displaying the mix parameters

for individual channels.............................................. 105

Channel Library Operation .......................................108

Calling the Channel Library screen......................108

Changing Channel Library Names.......................109

Storing Channel Library settings..........................109

Recalling Channel Library settings ...................... 110

Erasing Channel Library settings .........................110

13. AUX 111

About the AUX buses ............................................... 111

AUX Send Level Adjustment .................................... 111

Using external effects with the AUX buses ..............113

14. Effects 115

About the Internal Effects ......................................... 115

Recalling Effect Library settings ............................... 116

Applying Effects via Send and Return...................... 117

Inserting an Effect Into a Channel ............................ 119

Editing Effects ..........................................................121

Effect Library Operations.......................................... 122

Call the Effect Library Screen ..............................122

Changing Effect Library Names ...........................122

Storing Effect Library settings ..............................123

Erasing Effect Library settings .............................123

Correcting a Vocal Track (Pitch Fix)......................... 124

15. Track operations and editing 127

About the AW2400’s tracks ...................................... 127

Audio track operations.............................................. 128

About audio tracks ...............................................128

Viewing all audio tracks ....................................... 128

Muting a specific audio track................................ 129

Switching the virtual track of an audio track......... 129

Editing virtual track names for an audio track ......130

Stereo track operations ............................................130

About the stereo track..........................................130

Recording on the stereo track..............................131

Playing back the stereo track...............................131

Switching the virtual track of the stereo track ...... 132

Editing the name of a virtual track

for the stereo track ..........................................132

The Trigger Track Function ......................................133

About Trigger Track..............................................133

Using the Trigger Track Function .........................134

Editing tracks ............................................................135

Basic procedure for track editing ..............................136

List of editing command............................................138

ERASE .................................................................138

DELETE ...............................................................138

INSERT ................................................................138

COPY ...................................................................139

MOVE...................................................................140

EXCHANGE .........................................................141

TIME COMP (Time Compression/Expansion)......141

PITCH (Pitch Change)..........................................142

IMPORT CD AUDIO.............................................142

IMPORT CD WAV ................................................142

IMPORT USB WAV..............................................142

IMPORT TRACK ..................................................142

EXPORT...............................................................142

MERGE ................................................................142

Importing audio data/WAV files ................................143

Importing from the CD-RW drive ..........................143

Importing audio data from another song ..............145

16. Pan, EQ, and Dynamics Processing 147

Pan Control...............................................................147

4-band EQ ................................................................149

Dynamics Processing ...............................................151

Using the Gates....................................................151

Using the Compressors........................................152

EQ/Dynamics Processor Library Operation..............154

Accessing the EQ/Dynamics Library screens ......154

Changing EQ/Dynamics Library Names...............156

Recalling EQ/Dynamics Library settings ..............156

Storing EQ/Dynamics Library settings..................157

Erasing EQ/Dynamics Library settings.................157

17. Scene Memory 159

About Scene Memory ...............................................159

Scene Memory Operation.........................................159

Renaming a scene ...............................................160

Recalling scene data............................................160

Storing scene data ...............................................161

Deleting scene data..............................................161

Protecting a scene................................................161

Using the Recall Safe function..................................162

Moving scenes..........................................................163

AW2400 Owner’s Manual

10

Contents

18. Song management 165

About songs .............................................................165

Managing Your Songs.............................................. 167

Editing various settings for the song ........................174

Creating a tempo map.............................................. 175

Backing up songs ..................................................... 177

Restoring songs .......................................................178

Exchanging Song Data

With Other AW-series Audio Workstations............... 180

19. Automix 181

About Automix .......................................................... 181

Automix Operation.................................................... 181

Creating a New Automix Recording.....................182

Recording the Automix Data ................................ 183

Automix Playback ................................................ 185

Punch In and Out of Automix ............................... 185

Command Editing Automix data

In a Specified Region ...............................................186

Editing Individual Automix Events ............................188

Automix Library Operation........................................ 190

About the Automix Library Page ..........................190

Changing Automix Names ...................................190

Storing Automix settings ......................................191

Recalling Automix settings...................................191

Erasing Automix settings ..................................... 191

Protecting Automix Data ......................................192

20. MIDI 193

What you can do using MIDI ....................................193

Basic MIDI Settings .................................................. 194

MIDI Synchronization Message Setup .....................198

Connecting to External Equipment........................... 200

Synchronizing the AW2400

With External MIDI Devices.............................200

Switching AW2400 scenes

from an external MIDI device ..........................201

Recording/playing AW2400

mix operations on an external sequencer .......202

Using the MIDI Remote function ..............................204

About the MIDI Remote function..........................204

Using the MIDI Remote function presets .............204

Using User-defined Remote function ................... 206

Remotely controlling a tone generator module ....207

21. Utility functions 209

Using the test tone oscillator ....................................209

AW2400 Preferences ...............................................210

Initializing the internal hard disk ...............................212

22. Creating an audio CD 213

Creating an audio CD ...............................................213

Types of media that you can use

with the CD-RW drive ...............................................213

Writing an audio CD..................................................214

Basic settings for the CD-RW drive ..........................215

Writing audio data.....................................................216

Writing Track At Once ..........................................217

Writing Disc At Once ............................................218

Finalizing CD-R/RW media.......................................220

Erasing CD-RW media .............................................221

Playing an audio CD .................................................222

23. Digital Input/Output &

Optional Card Settings 223

Wordclock and Cascade Settings.............................223

Select the Wordclock Source ...............................223

Fine Adjustment Of Overall

Song Pitch (Vari-pitch).....................................226

Cascade-connecting External Devices.................226

Check the Status Of the Digital Input Signal.............227

Plug-in Card Settings................................................228

24. USB 229

What You Can Do With USB ....................................229

WAV File Transfer (USB Storage Mode) ..................230

Switching to the USB Storage Mode....................230

Exiting the USB Storage Mode.............................232

Copying Exported WAV Files

To the Computer..............................................233

Importing Copied WAV Files

From the Computer..........................................234

Appendix 237

Mastering library list..................................................237

EQ Parameter list .....................................................238

Dynamics Parameters ..............................................240

Gate Parameter list...................................................243

Compressor Parameter list .......................................243

Effects Parameters ...................................................245

Troubleshooting ........................................................258

Display message list .................................................263

About the CD-ROM included with the AW2400 ........266

MIDI data format .......................................................272

MIDI Implementation Chart.......................................276

Specifications............................................................277

Dimensions ...............................................................279

Index .........................................................................280

Block diagram ...........................................................284

11

AW2400 Owner’s Manual

Before you start

1

Chapter 1

Before you start

This chapter explains what you should know before you begin using the

AW2400.

The AW2400 package contains the following items. If any

are missing, please contact your dealer.

• The AW2400

•Power cord

• Owner’s manual (this book)

• CD-ROM

Copying of commercially available music sequence data

and/or digital audio ﬁles for any purpose other than your

own personal use is strictly prohibited.

• Macintosh is a registered trademark of Apple Computer,

Inc. USA in the United States and other countries.

• Windows is a registered trademark of Microsoft Corpora-

tion USA in the United States and other countries.

• Cubase SX and Nuendo are trademarks of Steinberg

Media Technologies AG.

• Logic is a registered trademark of Apple Computer, Inc.

USA in the United States and other countries.

• SONAR is a registered trademark of Twelve Tone Sys-

tems, Inc.

• ProTools is a trademark or registered trademark of Avid

Technology, Inc. and afﬁliated companies.

• Other company names and product names in this docu-

ment are the trademarks or registered trademarks of

their respective owners.

http://www.yamahasynth.com/

http://www.yamaha.co.jp/manual/

Produced data can be lost due to breakdown or mistaken

operation. We recommend that you store all important

data on your computer, CD-R/CD-RW discs, or other

external storage medium.

Yamaha will accept no responsibility for any damages

(including consequential or incidental) incurred by the

customer or any third party as a result of loss or impair-

ment of the data stored on the hard disk or CD-R media,

regardless of whether such loss could have been or actu-

ally was foreseen by Yamaha.

Nor does Yamaha guarantee the media against any defect

that may render it unusable.

Introduction

■ Check the included items

■ Copyright

■ Trademarks

■ Yamaha Website (English only)

■ Yamaha Manual Library

Remember to back up your data

■ Storing produced data

■ Responsibility for loss of data, etc.

AW2400 Owner’s Manual

12

Before you start

1

A built-in CD-RW drive is a device that lets you create or

play audio CDs, backup and restore data from the internal

hard disk, and read data from a CD-ROM.

1 Never touch the objective lens.

B Be careful that the objective lens does not become

dusty or dirty.

C If the objective lens becomes dusty, use a commer-

cially available blower etc. to blow the dust off with

clean air.

D Since the inside of the drive contains powerful mag-

netic circuitry, do not allow any magnetic material to

come near the drive. (In particular, any metallic frag-

ments, screws, or pins that enter the drive mechanism

will cause operation to fail.)

To insert a disc into the CD-RW drive, press the eject

switch. The disc tray will open. Place the disc on the tray,

and gently push the disc tray in.

If you are unable to remove the disc by pressing the eject

switch, insert a wire of less than 2 mm diameter (such as a

straightened paper clip) into the eject hole, and push gen-

tly. However, pressing the eject switch will not eject the

disc when the AW2400 is in the following states, so do not

use this method in such cases.

• When the AW2400’s power is “OFF”

• When the disc is being accessed (data is being read,

written, or erased)

• While in CD PLAY mode

About the built-in CD-RW drive

• Even if a CD-RW drive is operating normally, it may fail a read

or write operation approximately once in ﬁve hundred times.

•Yamaha will take no responsibility for any damages, direct or

consequential, that may result from the use of the above CD-

RW drive.

IMPORTANT

■ Handling

Using the CD-RW drive

• The disc tray is ejected electrically. If the disc tray is not ejected

when you press the eject switch, turn on the power of the AW2400

and press the eject switch once again.

NOTE

Eject switchEject hole

■ Removing a CD in an emergency

• This removal method is for use in emergencies such as when

you cannot remove the disc due to a malfunction of the disc

tray or a power failure. Do not use this method unnecessarily,

since doing so will damage the CD-RW drive.

CAUTION

About the built-in CD-RW drive • Using the CD-RW drive

Installing an optional card

13

AW2400 Owner’s Manual

Before you start

1

By installing a separately sold mini-YGDAI card in a rear-

panel slot, you can add analog input/output jacks to the

AW2400 or allow connection of external digital devices.

The following types of cards can be used.

Refer to the Yamaha Pro Audio global website for the

most recent information on I/O cards.

http://www.yamahaproaudio.com

Before installing a card, you must check the Yamaha web-

site to make sure that this device is compatible.

http://www.yamahaproaudio.com

To install an optional mini-YGDAI card, proceed as

follows.

1

Make sure that the power is turned off.

2

Loosen the screws that hold the slot cover

in place, and remove the slot cover.

Keep the removed slot cover in a safe place.

3

Align the edges of the card with the guard

rails inside the slot, and insert the card into

the slot.

Push the card all the way into the slot so that the con-

nector at the end of the card is correctly mated with the

connector inside the slot.

4

Use the screws included with the card to

fasten the card in place.

Malfunctions or incorrect operation may occur if the

card is not fastened.

Installing an optional card

Card type Model

Number of

channels

Digital

format

Bit

depth

AD card

MY4-AD 4

—

24 bit

MY8-AD

8

20 bit

MY8-AD24

24 bit

MY8-AD96

DA card

MY4-DA 4

—

20 bit

MY8-DA96 8 24 bit

Digital I/O card

MY8-AE

8

AES/EBU

24 bit

MY8-AE96

MY8-AE96S

MY16-AE 16

MY8-AT 8

ADAT

MY16-AT 16

MY8-TD 8

TASCAM

MY16-TD 16

Waves Plug-in

DSP card

Y96K 8 ADAT 24bit

mLAN card MY16-mLAN 16 IEEE1394 24bit

■ Available optional cards

■ Installing an optional card

AW2400 Owner’s Manual

14

Before you start

1

15

AW2400 Owner’s Manual

Introducing the AW2400

2

Chapter 2

Introducing the AW2400

This chapter describes the features of the AW2400, the name of each part

and its function, and introduces terminology you need to know when using

the AW2400.

The AW2400 is an audio workstation that combines a digital mixer, multi-effect processor, hard

disk recorder, and CD-RW drive.

The following diagram shows the signal ﬂow within the AW2400.

Now let’s take a more detailed look at each section of the AW2400.

● Plenty of input channels with professional

features

The AW2400 digital mixer features 24-bit AD/DA conver-

sion with 32-bit internal processing for uncompromised

sound quality. 16 input channels, 24 track channels, and 4

stereo effect return channels provide plenty of input

capacity for most mixing situations.

The 8 AD input ([MIC/LINE INPUT] jacks 1–8), chan-

nels 1–16 on an optional I/O card installed in I/O slot, or

the stereo [DIGITAL STEREO IN] connector can be

selected for input.

The track channel 1–24 inputs are permanently assigned

to tracks 1–24, and the effect return channel 1–4 inputs are

permanently assigned to the outputs of internal effect pro-

cessors 1–4.

Features of the AW2400

Input channels 1–16

Track channels 1–24

Effect return channels 1–4

Bus1 L/R, Bus2 L/R

AUX buses 1–4

Effect buses 1–4

Stereo buses L/R

Stereo output channel

×8

×16

[MIC/LINE

INPUT]

jacks 1–8

×2

[DIGITAL

STEREO IN]

connector

I/O slot

Mixer

×

2

×2

Sound clip

×

24 ×24×2

Recorder input

patching

Recorder CD-R/RW drive

CD Write

Data Backup/Restore

WAV File Import

CD Play

×2

I/O card

[OMNI OUT] jacks 1-4

[DIGITAL STEREO OUT] connector

[STEREO OUT] jacks

[MONITOR OUT] jacks

[PHONES] jack

I/O card

×2

Metronome

Effect 1

×

2

×2

Effect 2

×

2

×2

Effect 3

×

2

×2

Effect 4

×

2

Internal Effects

×2

×16

×4

×2

■ Mixer section

AW2400 Owner’s Manual

Features of the AW2400

Introducing the AW2400

16

2

● Totally redesigned operation

The AW2400 is designed to be operated directly by the

musician (guitarist, vocalist, drummer etc.). Input signal

track assignment, mixdown and bounce recording set-

tings, tracking with effects/EQ/dynamics, compressor set-

tings, and much more can be easily handled with simple,

straightforward operation.

● Four-band EQ and dynamics processors on

each channel

Four-band full-parametric EQ and dynamics processing is

provided on virtually every channel. You can recall the

desired preset from the library, and use the panel knobs

and keys to quickly adjust the settings.

● Four high-quality multi-effect units built-in

The four built-in effect units deliver a wide variety of

effects including ambience effects such as reverb and

delay, modulation type effects such as chorus and ﬂanger,

and guitar-type effects such as distortion and amp simula-

tion. These effects can be used either via send/return, or

inserted into a desired channel.

● Automix capability

Full automix production power is provided with 13 motor

faders for comprehensive fader control, pan control, scene

recall and library recall capability.

● I/O slot for expansion with optional I/O cards

Expanded inputs and outputs can be provided in ADAT,

TASCAM, AES/EBU, and other formats. Optional DSP

cards can also be used to provide extra signal processing

capability via the I/O slot.

● 16-track Simultaneous Recording & 24-track

Simultaneous Playback (16-bit songs)

You can record multiple instrument tracks one by one, or

set up multiple mics to record a drum set or a live perfor-

mance by an entire band. A stereo track for direct mix-

down of all 24 tracks is also provided, letting you manage

the multi-track audio and the two-track mix as a single

data package.

8 virtual tracks are available for the recorder tracks as well

as the stereo track. When recording parts or when doing a

mix, you can switch virtual tracks to record multiple takes

and select the best take later.

The “bit depth” (number of quantization bits) of the audio

data recorded on each track can individually be set to 16

or 24 bits for each song. 16-bit songs allow simultaneous

recording of up to 16 tracks, and simultaneous playback of

up to 24 tracks. 24-bit songs allow simultaneous recording

up to 8 tracks, and simultaneous playback of up to 12

tracks (→ p. 165).

The recording sampling frequency can also be set to either

44.1 kHz or 48 kHz (the selected sampling has no effect

on the number of simultaneous record or playback tracks).

● Trigger track function

The “Trigger Track” function allows the track [ON] keys

and faders to be used to start and stop playback of

recorded tracks. This is ideal for performance situations in

which you want to switch phrases or patterns in real time,

or when you need to start background music on cue, for

example.

● Versatile editing functionality

Audio data recorded on a track can be copied, moved, or

edited using a variety of commands. You can make

detailed edits, or even make radical changes to the struc-

ture of the song by using the same riff repeatedly or

increasing the number of choruses.

“Time Compression” lets you compress or expand the

time axis of the audio data over a range of 50%–200%.

“Pitch Change” lets you modify the pitch over a range of

up or down one octave. You can use the Undo function to

undo the results of as many as the last ﬁfteen editing oper-

ations.

● A variety of Locate methods, and auto

punch-in/out

Eight locate points (start/end, relative zero, A/B, in/out,

quick locator) and 99 markers can be assigned at any

desired point in the song for quick access via Locate oper-

ations. Auto punch-in/out and A-B repeat playback func-

tions are also provided. The AW2400 also has a

metronome that follows the tempo map.

● Sound Clip function

The Sound Clip function lets you record and play back an

input signal without using the recorder tracks. You can use

this function to make quick sketches of song or arrange-

ment ideas. You can transfer recorded sound clip data to

the recorder as required.

● Vocal Editing with Pitch Fix

A Pitch Fix function is provided to allow precise adjust-

ment of the pitch of a vocal track as well as the generation

of chorus parts from a main vocal line. This feature can

also be used to change the character of a vocal sound.

■ Recorder section

17

AW2400 Owner’s Manual

Introducing the AW2400

2

A dedicated CD-RW drive is installed in the AW2400. You

can produce an audio CD containing the stereo mixes of

songs recorded on the hard disk. Markers assigned within

a song can also be used as the CD track numbers. You can

even use advanced techniques such as assigning more than

one track number within a single song. The CD-RW drive

can also be used to backup/restore songs, to play back

audio CDs, and to load WAV data from a CD-ROM.

The AW2400 can be directly connected to a computer via

the built-in USB interface, which enables transferring

audio ﬁles as well as MIDI messages. This allows WAV-

format audio ﬁles to be copied between the AW2400 and

computer for convenient management and processing in

computer-based applications, and “backup” song ﬁles can

be stored on the computer’s memory media.

Here’s a quick overview of terminology used with the AW2400.

A location where data is recorded is called a “track.” The

AW2400’s recorder section uses the following types of

track.

● Audio tracks

The physical tracks used to record and play back audio

data are called “audio tracks,” or simply “tracks.” The

AW2400 has 24 audio tracks. You can record 16 tracks

simultaneously, and play back 24 tracks simultaneously

(16-bit songs).

● Stereo track

The AW2400 has a “stereo track” that is independent from

audio tracks 1–24, and which records and plays a stereo

audio signal. The stereo track is used mainly as a dedi-

cated mixdown track for recording the ﬁnal mix.

● Virtual tracks

Each of the 24 audio tracks and the stereo track consists of

eight “virtual” tracks. For the audio tracks and the stereo

track, only one virtual track can be recorded or played at

any time. However, you can switch virtual tracks to con-

tinue recording other takes while preserving the previ-

ously-recorded content.

The diagram below shows the concept of virtual tracks.

The horizontal rows indicate audio tracks 1–24, and the

vertical columns correspond to virtual tracks 1–8. The

shaded areas indicate the virtual track that is currently

selected for recording or playback.

● Trigger tracks

The “Trigger Track” function allows the track [ON] keys

and faders to be used to start and stop playback of

recorded tracks. When the Trigger Track function is

engaged and you press a track channel [ON] key, the cor-

responding track will playback one time from the begin-

ning of the song to the end of the recorded data.

■ CD-RW drive

■ Connecting to a Computer

AW2400 terminology

Recorder section

■ Tracks

1

2

3

4

5

6

7

8

1

2 3 4 5 6 7 8

1

2

3

4

5

6

7

8

21 22 23 24

Audio tracks

Stereo track

Virtual tracksVirtual tracks

Features of the AW2400 • AW2400 terminology

AW2400 Owner’s Manual

AW2400 terminology

Introducing the AW2400

18

2

Locations within a song that you speciﬁed in order to exe-

cute a function such as auto punch-in/out or A-B repeat

playback are called “locate points.” Locate points include

in/out points and the A/B points. You can use the Locate

section keys to move instantly to these points.

You can assign “markers” at desired locations within a

song independently of the locate points so that you can

ﬁnd these locations quickly. The AW2400 lets you set up

to ninety-nine markers (1–99). By using the keys Locate

section you can move instantly to the previous or next

marker.

A signal path that processes a single signal within the

mixer and sends it to various sections is called a “chan-

nel.”

The mixer section of the AW2400 provides the following

channels.

● Input channels 1–16

Input channels provide level control, EQ, and dynamics

processing for signals that are input via the [MIC/LINE

INPUT] jacks 1–8, the [DIGITAL STEREO IN] connec-

tor, and/or an I/O card installed in the rear-panel slot, and

send them to the recorder tracks or to the [STEREO OUT]

jacks.

● Track channels 1–24

These channels provide level adjustment, EQ, and dynam-

ics processing for the audio playback signals from audio

tracks 1–24 of the recorder, and send the signals to the ste-

reo track and the [STEREO OUT] jacks. You can also per-

form “bounce recording” by sending these channels to

different tracks.

● Effect return channels 1–4

These channels send the signals returned from the internal

effects to the stereo track and the [STEREO OUT] jacks.

● Stereo output channel

This channel provides level adjustment, EQ, and dynamics

processing for the stereo bus signal (which carries the mix

of the other channels), and sends it to the stereo track or to

the [STEREO OUT] jacks. The same signal is also output

from the [MONITOR OUT] jacks and from the

[PHONES] jack.

● Bus master channels 1/2

Provide level adjustment, EQ, and dynamics processing

for the signals from bus 1 and bus 2, and sends the signals

to the audio tracks.

● AUX send master channels 1–4

Provide ﬁnal level adjustment for the AUX buses, as well

as EQ and dynamics processing.

● Effect send master channels 1–4

Provide ﬁnal level adjustment for the effect buses, as well

as dynamics processing.

In order to efﬁciently handle numerous input channels the

AW2400 mixer section channels are organized in “mixing

layers”. The diagram shows an overview of the AW2400’s

6 mixing layers.

The channels available in each of the mixing layers are as

follows.

1 Mixing Layer IN 1-8

Input channels 1–8 and effect return channels 1–4.

B Mixing Layer IN 9-16

Input channels 9–16 and effect return channels 1–4.

C Mixing Layer MASTER

Bus master channels 1/2, AUX send master channels 1–4,

and effect send master channels 1–4.

D Mixing Layer TRACK 1-12

Track channels 1–12.

E Mixing Layer TRACK 13-24

Track channels 13–24.

F REMOTE Layer

A special layer for remote control of external MIDI

devices.

■ Locate points/markers

Mixer section

■ Channels

■ Mixing Layers

A

B

C

D

E

F

AW2400 terminology

19

AW2400 Owner’s Manual

Introducing the AW2400

2

Channel pan, EQ, dynamics processor and other settings

are known as “mix parameters”. All mix parameters can

be saved together as “scenes” that can be recalled when-

ever necessary. Furthermore, specialized libraries are pro-

vided for various parameter groups – EQ, effects, etc. –

that can be saved and recalled individually for each chan-

nel.

For effect return channels 1–4, stereo output channel, and

bus master channel 1–2, the parameters (except for pan)

are always linked for adjacent pairs of channels. These are

called “paired channels.”

For input channels 1–16, track channels 1–24, and AUX

send master channels 1–4, you can also assign adjacent

odd-numbered/even-numbered channels to function as

paired channels. The parameters (except for pan and

phase) of paired channels will be linked, so that adjusting

one parameter will cause the same parameter of the other

channel to be adjusted accordingly.

A signal route that mixes the signals from multiple chan-

nels and sends them to an output jack or recorder track

input is called a “bus.”

Unlike channels, which handle only a single signal, a bus

can combine multiple signals into one or two (stereo) out-

puts and send them to a destination.

The AW2400’s mixer section provides the following

buses.

● Stereo bus

This bus mixes the input signals to stereo, and sends them

via the stereo output channel to the stereo track of the

recorder or to the [STEREO OUT] jacks. Normally the

same signal output via the [STEREO OUT] jacks is also

output via the [MONITOR OUT] and [PHONES] jacks.

● AUX buses 1–4

These buses mix the signals from the track, input, and

effect return channels and send them to the speciﬁed out-

put connector. Use these when you will use an external

effect processor, or to create a mix differing from the ste-

reo channel for musicians to monitor.

● Effect buses 1–4

These buses combine the signals from the track and input

channels, and input them to built-in effects 1–4.

● Bus 1, Bus 2

These buses mix track, input, and effect return channels

and send them to the inputs of free tracks. Bus 1 and bus 2

are used for bounce (ping-pong) recording.

The smallest unit by which the AW2400 manages a com-

position is called a “song.” When you save a song on the

hard disk, all data necessary for reproducing that song will

be saved; i.e., not just the audio data, but also the mixer

settings and the automix settings. You can return to the

original state at any time by loading the saved song.

A “scene” is a stored set of settings for the mixer section

and effects. The area of memory that holds the scenes is

called “scene memory,” and 99 scenes can be stored for

each song. Scene memories are saved on the hard disk as

part of the song.

A “library” is an area of memory that stores individual set-

tings such as for EQ or dynamics. The AW2400 has sepa-

rate libraries for EQ, dynamics, effect, channel, and

mastering settings.

Recalling a scene affects all mixer section settings, while

the libraries allow only speciﬁed settings to be recalled as

required. You can also save the settings from one channel

and copy them to other channels, for example.

Each library is saved on the hard disk as part of the song.

The “tempo map” records changes in tempo and time sig-

nature that occur during the course of a song. The tempo

map is saved on the hard disk as part of the song.

Various global settings that apply to all songs are collec-

tively referred to as “system data.” System data is stored

on the hard disk independently of the individual songs.

■ Mix Parameters

■ Paired channels

■ Buses

Overall

■ Songs

■ Scenes and scene memories

■ Libraries

■ Tempo map

■ System data

AW2400 Owner’s Manual

Parts of the AW2400 and what they do

Introducing the AW2400

20

2

This section explains the names and functions of the various items on the AW2400’s top panel,

rear panel, and front panel.

Parts of the AW2400 and what they do

Top panel

Work Navigate

section (P. 21)

Analog Input section (P. 21)

Quick Navigate section

(P. 21)

Display section (P. 22)

Mixer section (P. 23)

Selected Channel

section (P. 24)

Monitor section (P. 24)

Scene/Automix/USB section (P. 24) Data entry/control

section (P. 25)

Locate/Number section (P. 25)

Layer section (P. 26)

Locate section (P. 27)

Transport section

(P. 27)

Sayfa yükleniyor ...

Yamaha AW2400 Kullanım kılavuzu

Yamaha AW2400 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler