Hilti HDE 500-A12 Cordless Mortar Dispenser Kullanım kılavuzu

HDE 500A12

English 1

Dansk 12

Svenska 23

Norsk 35

Suomi 46

Türkçe 57

ﻋﺮﺑﻲ 69

日本語 82

한국어 93

繁體中文 104

中文 114

1

2

3

4

5

6

7

8

HDE 500A12

en Originaloperatinginstructions....................................... 1

da Originalbrugsanvisning .......................................... 12

sv Originalbruksanvisning........................................... 23

no Originalbruksanvisning .......................................... 35

fi Alkuperäisetohjeet ............................................. 46

tr Orijinalkullanımkılavuzu ......................................... 57

ar ﺩﻟﻴﻞﺍﻻﺳﺘﻌﻤﺎﻝﺍﻷﺻﻠﻲ .......................................... 69

ja オリジナル取扱説明書 ............................................ 82

ko 오리지널사용설명서............................................. 93

zh 原始操作說明.................................................. 104

cn 原版操作说明.................................................. 114

*2330326* 2330326 English 1

Original operating instructions

1 Information about the operating instructions

1.1 About these operating instructions

• Read these operating instructions before the product is used or operated for the first time. This is a

prerequisite for safe, trouble-free handling and use of the product.

• Observe the safety instructions and warnings in these operating instructions and on the product.

• Always keep the operating instructions with the product and make sure that the product is accompanied

by these operating instructions only, when the product is given to other persons.

1.2 Explanation of symbols

1.2.1 Warnings

Warnings alert persons to hazards that occur when handling or using the product. The following signal words

are used:

DANGER

DANGER !

▶Draws attention to imminent danger that will lead to serious personal injury or fatality.

WARNING

WARNING !

▶Draws attention to a potential threat of danger that can lead to serious injury or fatality.

CAUTION

CAUTION !

▶Draws attention to a potentially dangerous situation that could lead to personal injury or damage to the

equipment or other property.

1.2.2 Symbols in the operating instructions

The following symbols are used in these operating instructions:

Comply with the operating instructions

Instructions for use and other useful information

Dealing with recyclable materials

Do not dispose of electric equipment and batteries as household waste

Hilti Liion battery

Hilti charger

1.2.3 Symbols in illustrations

The following symbols are used in illustrations:

These numbers refer to the illustrations at the beginning of these operating instructions.

The numbering reflects the sequence of operations shown in the illustrations and may deviate

from the steps described in the text.

Item reference numbers are used in the overview illustration and refer to the numbers used in

the key in the product overview section.

These characters are intended to specifically draw your attention to certain points when handling

the product.

2 English 2330326 *2330326*

1.3 Product-dependent symbols

1.3.1 Symbols on the product

The following symbols can be used on the product:

National waste-materials management system

“Off” position

Continuous dispensing

Measured dispensing 5...80 ml

Measured dispensing 1...16

Direct current (DC)

The product supports near-field communication (NFC) technology compatible with iOS and

Android platforms.

Li-ion battery

Never use the battery as a striking tool.

Do not drop the battery. Never use a battery that has suffered an impact or is damaged in any

other way.

1.4 Product information

products are designed for professional users and only trained, authorized personnel are

permitted to operate, service and maintain the products. This personnel must be specifically informed about

the possible hazards. The product and its ancillary equipment can present hazards if used incorrectly by

untrained personnel or if used not in accordance with the intended use.

The type designation and serial number are printed on the rating plate.

▶Write down the serial number in the table below. You will be required to state the product details when

contacting Hilti Service or your local Hilti organization to inquire about the product.

Product information

Cordless dispenser: HDE 500-A12

Generation: 01

Serial number:

1.5 Declaration of conformity

The manufacturer declares, on his sole responsibility, that the product described here complies with the

applicable legislation and standards. A copy of the declaration of conformity can be found at the end of this

documentation.

The technical documentation is filed here:

Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | D-86916 Kaufering, Germany

2 Safety

2.1 General power tool safety warnings

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this

power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

*2330326* 2330326 English 3

Work area safety

▶Keep work area clean and well lit. Cluttered or dark areas invite accidents.

▶Do not operate power tools in explosive atmospheres, such as in the presence of flammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

▶Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

Electrical safety

▶Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter

plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of

electric shock.

▶Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

▶Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

▶Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

▶When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

▶If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

▶Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools may result in serious personal injury.

▶Use personal protective equipment. Always wear eye protection. Protective equipment such as a

dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will

reduce personal injuries.

▶Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power

source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on

the switch or energising power tools that have the switch on invites accidents.

▶Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

▶Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

▶Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

▶If devices are provided for the connection of dust extraction and collection facilities, ensure these

are connected and properly used. Use of dust collection can reduce dust-related hazards.

▶Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore

tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

▶Do not force the power tool. Use the correct power tool for your application. The correct power tool

will do the job better and safer at the rate for which it was designed.

▶Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

▶Disconnect the plug from the power source and/or remove the battery pack, if detachable, from

the power tool before making any adjustments, changing accessories, or storing power tools.

Such preventive safety measures reduce the risk of starting the power tool accidentally.

▶Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

▶Maintain power tools and accessories. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained power

tools.

▶Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

4 English 2330326 *2330326*

▶Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

▶Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

▶Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with another battery pack.

▶Use power tools only with specifically designated battery packs. Use of any other battery packs may

create a risk of injury and fire.

▶When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a fire.

▶Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

▶Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may

exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

▶Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature

above 130° C (265 °F) may cause explosion.

▶Follow all charging instructions and do not charge the battery pack or tool outside the temperature

range specified in the instructions. Charging improperly or at temperatures outside the specified range

may damage the battery and increase the risk of fire.

Service

▶Have your power tool serviced by a qualified repair person using only identical replacement parts.

This will ensure that the safety of the power tool is maintained.

▶Never service damaged battery packs. Service of battery packs should only be performed by the

manufacturer or authorized service providers.

2.2 Additional safety instructions

Personal safety

▶Never tamper with or modify the product or accessories in any way.

▶Use the product and accessories only when they are in perfect working order.

▶Risk of injury by falling tools and/or accessories. Before starting work, check that the battery and installed

accessories are secure.

▶Wear eye protection and protective gloves when changing accessories.

▶Prior to use, read and comply with the safety data sheet for the product, the instructions on the packaging

and the instructions for use of the foil pack.

▶Begin injecting the compound until it is in the immediate working area.

▶Never point the product toward yourself or other persons.

▶Never leave the product unattended.

▶Do not use the product if parts are damaged or if operating controls do not function faultlessly. Have the

product repaired by Hilti Service.

Safety at the workplace

▶Keep the workplace tidy. Objects which could cause injury should be removed from the working area.

▶Wear non-skid shoes.

▶Take the influences of the surrounding area into account. Do not use the product where there is a risk of

fire or explosion.

▶Do not use faulty/worn-out foil pack holders.

2.3 Careful handling and use of batteries

▶Comply with the following safety instructions for the safe handling and use of Li-ion batteries.

Failure to comply can lead to skin irritation, severe corrosive injury, chemical burns, fire and/or explosion.

▶Use only batteries that are in perfect working order.

▶Treat batteries with care in order to avoid damage and prevent leakage of fluids that are extremely

harmful to health!

▶Do not under any circumstances modify or tamper with batteries!

*2330326* 2330326 English 5

▶Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C

(176 °F).

▶Never use or charge a battery that has suffered an impact or been damaged in any other way. Check

your batteries regularly for signs of damage.

▶Never use recycled or repaired batteries.

▶Never use the battery or a battery-operated power tool as a striking tool.

▶Never expose batteries to the direct rays of the sun, elevated temperature, sparking, or open flame. This

can lead to explosions.

▶Do not touch the battery poles with your fingers, tools, jewelry, or other electrically conductive objects.

This can damage the battery and also cause material damage and personal injury.

▶Keep batteries away from rain, moisture and liquids. Penetrating moisture can cause short circuits,

electric shock, burns, fire and explosions.

▶Use only chargers and power tools approved for the specific battery type. Read and follow the relevant

operating instructions.

▶Do not use or store the battery in explosive environments.

▶If the battery is too hot to touch, it may be defective. Put the battery in a place where it is clearly visible

and where there is no risk of fire, at an adequate distance from flammable materials. Allow the battery to

cool down. If it is still too hot to touch after an hour, the battery is faulty. Consult Hilti Service or read the

document entitled "Instructions on safety and use for Hilti Li-ion batteries".

Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.

→ page 10

Read the instructions on safety and use of Hilti Li-ion batteries that you can access by scanning

the QR code at the end of these operating instructions.

3 Description

3.1 Overview 1

@Front locating lug for installation of the foil

pack holder / cartridge

;Cradle for the foil pack holder / cartridge

=Rear locating lug for installation of the foil

pack holder / cartridge

%Dispensing mode selector switch

&Parallel piston rods with grip

(Release button

)Grip

+Battery

§Battery release buttons (also used to activate

the charge status indicator)

/Trigger

Accessories

:Foil pack

∙Foil pack holder, black

$Foil pack holder, red

£Cartridge

6 English 2330326 *2330326*

3.2 Intended use

The product is designed to dispense the contents of Hilti foil packs and cartridges in a controlled operation.

The HDE 500A12 cordless dispenser is designed exclusively for use with Hilti 330 ml or 500 ml foil packs

and 580 ml cartridges.

The product can be used with either a foil pack holder or a cartridge:

• Use only Hilti Li-ion batteries of the B12 series with this product. For optimum performance, Hilti

recommends the batteries stated in the table at the end of these operating instructions for this product.

• For these batteries, use only Hilti chargers of the type series stated in the table at the end of these

operating instructions.

3.3 Items supplied

Dispenser and operating instructions

Other system products approved for use with this product can be found at your local Hilti Store or at:

www.hilti.group

3.4 Charge state display

The charge state of the Liion battery is displayed after pressing one of the release buttons lightly (press only

until slight resistance is felt).

Status Meaning

4 LEDs show. Charge state: 75 % to 100 %

3 LEDs show. Charge state: 50 % to 75 %

2 LEDs show. Charge state: 25 % to 50 %

1 LED shows. Charge state: 10 % to 25 %

1 LED flashes. • Charge state: < 10 %

Battery charge state cannot be displayed while the

control switch is pressed and for up to 5 seconds

after releasing the control switch.

4 Technical data

HDE 500-A12

Weight in accordance with EPTA Procedure 01, without battery 1.8 kg

Rated voltage 10.8 V

Storage temperature −40 ℃ … 85 ℃

Ambient temperature for operation −17 ℃ … 60 ℃

4.1 Battery

Battery operating voltage 10.8 V

Weight, battery See the end of these operating

instructions

Ambient temperature for operation −17 ℃ … 60 ℃

Storage temperature −40 ℃ … 85 ℃

Battery charging starting temperature −10 ℃ … 45 ℃

4.2 Noise information and vibration values in accordance with EN 62841

The sound pressure and vibration values given in these instructions were measured in accordance with a

standardized test and can be used to compare one power tool with another. They can also be used for a

preliminary assessment of exposure.

The data given represent the main applications of the power tool. However, if the power tool is used for

different applications, with different accessory tools, or is poorly maintained, the data can vary. This can

significantly increase exposure over the total working period.

*2330326* 2330326 English 7

An accurate estimation of exposure should also take into account the times when the tool is switched off, or

when it is running but not actually being used for a job. This can significantly reduce exposure over the total

working period.

Identify additional safety measures to protect the operator from the effects of noise and/or vibration, for

example: maintaining the power tool and accessory tools, keeping the hands warm, organization of work

patterns.

Noise information

HDE 500-A12

Typical A-weighted sound power level (LWA)75.5 dB

Uncertainty for measured sound power level (KWA)3 dB

Typical A-weighted emission sound pressure level (LpA)64.5 dB

Uncertainty for the sound pressure level (KpA)3 dB

Vibration information

Total vibration (ah) B 12/2.6 Li-Ion 0.2 m/s²

B 1230 0.2 m/s²

Uncertainty (Kah)1.5 m/s²

5 Preparations at the workplace

WARNING

Risk of injury by inadvertent starting!

▶Before inserting the battery, make sure that the product is switched off.

▶Remove the battery before making any adjustments to the power tool or before changing accessories.

Observe the safety instructions and warnings in this documentation and on the product.

5.1 Charging the battery

1. Before charging the battery, read the operating instructions for the charger.

2. Make sure that the contacts on the battery and the contacts on the charger are clean and dry.

3. Use an approved charger to charge the battery. → page 6

5.2 Inserting the battery

WARNING

Risk of injury by short circuit or falling battery!

▶Before inserting the battery, make sure that the contacts on the battery and the contacts on the product

are free of foreign matter.

▶Make sure that the battery always engages correctly.

1. Charge the battery fully before using it for the first time.

2. Push the battery into the product until it engages with an audible click.

3. Check that the battery is seated securely.

5.3 Removing the battery

1. Press the battery release buttons.

2. Remove the battery from the product.

5.4 Fall arrest 2

WARNING

Risk of injury by falling tool and/or accessory!

▶Use only the Hilti tool tether recommended for your product.

▶Prior to each use, always check the attachment point of the tool tether for possible damage.

▶Do not secure a tool tether to the belt hook. Do not use a belt hook to lift the product.

8 English 2330326 *2330326*

Comply with the national regulations for working at heights.

As drop arrester for this product, use the Hilti tool tether #2261970 or #2261971.

▶Secure the carabiner to a load-bearing structure. Check that the carabiner holds securely.

▶Depending on which type of Hilti tool tether is used, secure either the second carabiner or the loop to

the product as shown in the illustration. Check that it holds securely.

Comply with the operating instructions of the Hilti tool tether.

5.5 Inserting the foil pack holder and foil pack 3

CAUTION

Trap hazard Hands can be trapped if care is not exercised when swiveling the foil pack holder closed.

▶Keep your hands clear of the cradle area when swiveling the foil pack holder into position.

CAUTION

Risk of injury Chemicals hazard.

▶Check the foil pack holder for damage and soiling. Both pistons must move smoothly and easily in both

directions over the full length of their travel in the foil pack holder. Replace the foil pack holder if it is

damaged and/or badly soiled.

1. Press the release button.

2. Pull the piston rod back as far as they will go.

3. Fit the front end of the foil pack holder into the front locating lug.

4. Pull the foil pack holder on to the rear locating lug and swivel the foil pack holder up.

5. Screw the static mixer (mixing nozzle) onto the foil pack.

6. Push the foil pack into the foil pack holder.

7. Swivel the foil pack holder into the dispenser.

5.6 Inserting the cartridge 4

1. Press the release button.

2. Pull the piston rod back as far as they will go.

3. Fit the front end of the cartridge into the front locating lug.

4. Pull the cartridge on to the rear locating lug and swivel the cartridge up.

5. Screw the static mixer (mixing nozzle) onto the foil pack.

6. Swivel the cartridge into the dispenser.

5.7 Manually discarding the initial quantity of mortar 5

WARNING

Risk of injury Chemicals hazard.

▶Never point the dispenser toward yourself or other persons. Begin dispensing mortar only after the

mixing nozzle has been screwed on. Incorrect use can lead to injury.

You must discard the initially dispensed volume of mortar every time the static mixer (mixing nozzle)

is changed.

The initially dispensed mortar is not suitable for use.

1. Set the dispensing mode selector switch to .

2. Squeeze the trigger until the mixing nozzle is completely full.

*2330326* 2330326 English 9

3. Set the dispensing mode selector switch to the appropriate volume of mortar for discarding .

Discard the amount of mortar stated in the instructions for the foil pack.

One click of the dispensing wheel corresponds to 1 ml.

4. Discard the initially dispensed volume of mortar.

6 Operation

Observe the safety instructions and warnings in this documentation and on the product.

6.1 Injecting mortar 6

For each new foil pack and each new cartridge and if the mortar has hardened inside the mixing

nozzle, always use a new static mixer (mixing nozzle).

1. Press the trigger.

2. Inject the mortar.

6.2 Removing the foil pack holder and foil pack 7

1. Set the dispensing mode selector switch to .

2. Press the release button.

3. Pull the piston rod back as far as they will go.

4. Swivel the foil pack holder up.

5. Remove the foil pack.

6. Press the tab on the foil pack holder.

7. Press the foil pack holder down at the rear locating lug.

8. Pull the foil pack holder down from the front locating lug.

6.3 Removing the cartridge 8

1. Set the dispensing mode selector switch to .

2. Press the release button.

3. Pull the piston rod back as far as they will go.

4. Swivel the cartridge upwards.

5. Press the cartridge down at the rear locating lug.

6. Pull the cartridge down from the front locating lug.

7 Care and maintenance

WARNING

Risk of injury with battery inserted !

▶Always remove the battery before carrying out care and maintenance tasks!

Care of the product

• Carefully remove stubborn dirt.

• Carefully clean the ventilation slots, if present, with a dry brush.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

• Oil the piston rods when necessary.

Care of the Liion batteries

• Never use a battery with clogged ventilation slots. Clean the ventilation slots carefully using a dry, soft

brush.

• Avoid unnecessary exposure of the battery to dust and dirt. Never expose the battery to high levels of

moisture (e.g. by being dipped in water or left in the rain).

If a battery has been soaked by moisture, treat it as a damaged battery. Isolate it in a non-flammable

container and consult Hilti Service.

10 English 2330326 *2330326*

• Keep the battery free of oil and grease. Do not permit dust or dirt to accumulate unnecessarily on the

battery. Clean the battery with a dry, soft brush or a clean, dry rag.

Do not use cleaning agents containing silicone as these can attack the plastic parts.

• Use only a slightly damp cloth to clean the casing. Do not use cleaning agents containing silicone as

these can attack the plastic parts.

Maintenance

• Check all visible parts and controls for signs of damage at regular intervals and make sure that they all

function correctly.

• Do not operate the product if signs of damage are found or if parts malfunction. Have it repaired

immediately by Hilti Service.

• After cleaning and maintenance, fit all guards or protective devices and check that they function correctly.

To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare

parts, consumables and accessories approved by Hilti for use with the product can be found at your

local Hilti Store or online at: www.hilti.group.

8 Transport and storage of cordless tools and batteries

Transport

CAUTION

Accidental starting during transport !

▶Always transport your products with the batteries removed!

▶Remove the battery/batteries.

▶Never transport batteries loose and unprotected. During transport, batteries should be protected from

excessive shock and vibration and isolated from any conductive materials or other batteries that may

come in contact with the terminals and cause a short circuit. Comply with the locally applicable

regulations for transporting batteries.

▶Do not send batteries through the mail. Consult your shipper for instructions on how to ship undamaged

batteries.

▶Prior to each use and before and after prolonged transport, check the product and the batteries for

damage.

Storage

WARNING

Accidental damage caused by defective or leaking batteries !

▶Always store your products with the batteries removed!

▶Store the product and the batteries in a cool and dry place. Comply with the temperature limits stated in

the technical data.

▶Do not store batteries on the charger. Always remove the battery from the charger when the charging

operation has completed.

▶Never leave batteries in direct sunlight, on sources of heat, or behind glass.

▶Store the product and batteries where they cannot be accessed by children or unauthorized persons.

▶Prior to each use and before and after prolonged storage, check the product and the batteries for

damage.

8.1 Transport and storage of dispensers

▶For transporting and storing the tool, set the dispensing mode selector switch to .

9 Troubleshooting

If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by

yourself, please contact Hilti Service.

9.1 Troubleshooting

If a problem occurs, always observe the charge-status and fault indicator of the battery. See the section

headed Status indicators of the Liion battery.

*2330326* 2330326 English 11

If the trouble you are experiencing is not listed in this table or you are unable to rectify the problem by

yourself, contact Hilti Service.

Trouble or fault Possible cause Action to be taken

Product does not work. The battery is not fully inserted. ▶Push the battery in until it

engages with an audible click.

Battery is discharged. ▶Change the battery.

Dispensing mode selector switch

set to

▶Select the desired dispensing

volume.

The battery does not engage

with an audible click. The retaining lug on the battery is

dirty.

▶Clean the retaining lug and push

the battery in until it engages.

If the problem persists, consult

Hilti Service.

The product or battery gets

very hot. The product is overloaded (appli-

cation limits exceeded).

▶Pay attention to the power

and performance rating of the

product before using it, i.e

check its suitability for the job

on hand. See “Technical data”

section.

Electrical fault ▶Switch the product off immedi-

ately, remove the battery, keep

it under observation, allow it

to cool down and contact Hilti

Service.

The battery runs down more

quickly than usual. Very low ambient temperature. ▶Allow the battery to warm up

slowly to room temperature.

Product prematurely aborts

dispensing operation The overload cut-out is activated;

mortar in the mixing nozzle has

hardened

▶Replace the static mixer (mixing

nozzle).

The overload cut-out is activated;

The dispensing pressure required

is too high for the product.

▶Increase the foil pack tempera-

ture.

Foil pack empty ▶Replace the empty foil pack.

The foil pack holder cannot

be swiveled into the product. The foil pack is not pushed fully

into the holder.

▶Push the foil pack into the foil

pack holder as far as it will go.

Piston rods not pulled back fully ▶Press the release button and

pull the piston rods all the way

back.

The foil pack holder does not

engage with an audible click The retaining lugs are dirty ▶Clean the retaining lugs.

The retaining lugs are defective ▶Insert a different foil pack

holder. Contact Hilti Service if

the problem persists.

No mortar is dispensed from

the mixing nozzle Mortar in the mixing nozzle has

hardened

▶Unscrew the mixing nozzle

containing the hardened mortar

and fit a new mixing nozzle.

10 Disposal

WARNING

Risk of injury due to incorrect disposal! Health hazards due to escaping gases or liquids.

▶DO NOT send batteries through the mail!

▶Cover the terminals with a non-conductive material (such as electrical tape) to prevent short circuiting.

▶Dispose of your battery out of the reach of children.

▶Dispose of the battery at your Hilti Store, or consult your local governmental garbage disposal or public

health and safety resources for disposal instructions.

12 Dansk 2330326 *2330326*

Most of the materials from which Hilti products are manufactured can be recycled. The materials must be

correctly separated before they can be recycled. In many countries, your old tools, machines or appliances

can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales representative for further information.

▶Do not dispose of power tools, electronic equipment or batteries as household waste!

11 Manufacturer’s warranty

▶Please contact your local Hilti representative if you have questions about the warranty conditions.

12 Further information

For more information on operation, technology, environment and recycling, follow this link:

qr.hilti.com/manual/?id=2330324&id=2330326

This link is also to be found at the end of the documentation, in the form of a QR code.

Original brugsanvisning

1 Om brugsanvisningen

1.1 Om denne brugsanvisning

• Læs brugsanvisningen grundigt igennem inden ibrugtagning. Det er en forudsætning for sikkert arbejde

og korrekt håndtering.

• Følg sikkerhedsanvisningerne og advarslerne i denne brugsanvisning og på produktet.

• Opbevar altid brugsanvisningen sammen med produktet, og overdrag kun produktet til andre personer

sammen med denne brugsanvisning.

1.2 Tegnforklaring

1.2.1 Advarsler

Advarsler advarer mod farer ved håndtering af produktet. Følgende signalord anvendes:

FARE

FARE !

▶Betegner en umiddelbart truende fare, der kan medføre alvorlige kvæstelser eller døden.

ADVARSEL

ADVARSEL !

▶Står ved en potentielt truende fare, der kan medføre alvorlige kvæstelser eller døden.

FORSIGTIG

FORSIGTIG !

▶Advarer om en potentielt farlig situation, der kan forårsage personskader eller materielle skader.

1.2.2 Symboler i brugsanvisningen

Der benyttes følgende symboler i denne brugsanvisning:

Se brugsanvisningen

Anvisninger for anvendelse og andre nyttige oplysninger

Håndtering af genvindbare materialer

Elektriske maskiner og batterier må ikke bortskaffes som almindeligt husholdningsaffald

Sayfa yükleniyor ...

Hilti HDE 500-A12 Cordless Mortar Dispenser Kullanım kılavuzu

Hilti HDE 500-A12 Cordless Mortar Dispenser Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Hilti HDE 500­-A12 Cordless Mortar Dispenser Kullanım kılavuzu

Hilti HDE 500­-A12 Cordless Mortar Dispenser Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Hilti HDE 500-A12 Cordless Mortar Dispenser Kullanım kılavuzu

Hilti HDE 500-A12 Cordless Mortar Dispenser Kullanım kılavuzu