Samsung HW-Q70T Kullanım kılavuzu

HW-Q70T

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - 3

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ENG - 4

CONTENTS

01 Checking the Components 6

02 Product Overview 7

Front Panel / Top Panel of the Soundbar ------------------------- 7

Bottom Panel of the Soundbar ------------------------- 8

03 Using the Soundbar Remote Control 9

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 9

How to Use the Remote Control

-------------------------

9

Using the Hidden Buttons (Buttons with more than one function)

-------------------------

12

Output specications for the different sound effect modes

-------------------------

12

Adjusting the Soundbar volume with a TV remote control ------------------------- 13

04 Connecting the Soundbar 14

Connecting the power and units

-------------------------

14

– Manually connecting the Subwoofer

-------------------------

15

– LED Indicator Lights on the Rear of Subwoofer

-------------------------

17

Connecting an SWA-9000S (Sold Separately) to your Soundbar

-------------------------

18

05 Using a wired connection to the TV 20

Method 1. Connecting with HDMI

-------------------------

20

– Connecting the TV that supports HDMI ARC (Audio Return Channel)

-------------------------

20

Method 2. Connecting using an Optical Cable

-------------------------

21

06 Using a wireless connection to the TV 23

Method 1. Connecting via Bluetooth

-------------------------

23

Method 2. Connecting via Wi-Fi

-------------------------

25

ENG - 5

07 Connecting an External Device 26

Method 1. Connecting using an HDMI Cable

(Capable of Dolby Atmos decoding and playback)

-------------------------

26

Method 2. Connecting using an Optical Cable

-------------------------

27

08 Connecting a Mobile Device 28

Method 1. Connecting via Bluetooth

-------------------------

28

Method 2. Connecting via Wi-Fi (Wireless Network)

-------------------------

31

09 Connecting an Amazon product 32

Connect and use with an Amazon product (Amazon Echo) ------------------------- 32

Use voice commands to control the Soundbar

-------------------------

32

Using the Tap Sound

-------------------------

33

10 Installing the Wall Mount 34

Installation Precautions

-------------------------

34

Wallmount Components

-------------------------

34

11 Installing the Soundbar above a TV Stand 36

Component

-------------------------

36

12 Software Update 37

Auto Update

-------------------------

37

USB Update

-------------------------

37

Initialisation

-------------------------

38

13 Troubleshooting 39

14 Licence 41

15 Open Source Licence Notice 41

16 Important Notes About Service 41

17 SpecicationsandGuide 42

Specications

-------------------------

42

ENG - 6

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Soundbar Remote Control /

Batteries

Subwoofer

x 2

Power Cord

(Subwoofer, Soundbar)

AC/DC Adapter

(Soundbar)

HDMI Cable

x 2

(M4 x L10)

x 2

Wall Mount Guide Holder-Screw Screw

x 2

x 4

Bracket-Wall Mount Rubber-Foot

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• For more information about the wallmount or rubber-foot, see pages 34~36.

• Design, specications, and App screen are subject to change without prior notice.

• The appearance of the accessories may differ slightly from the illustrations above.

ENG - 7

02 PRODUCT OVERVIEW

Front Panel / Top Panel of the Soundbar

Top Panel

Position the product so that

the SAMSUNG logo is

located on the top.

󰟳 󰟵

󰟶

󰟴

󰟳

(Power) Button

Turns the power on and off.

󰟴

(Volume) Button

Adjusts the volume.

󰟵

(Source) Button

Selects the source input mode.

Input mode Display

Optical Digital input D.IN

ARC (HDMI OUT) input D.IN  TV ARC (Auto conversion)

HDMI input HDMI

Wi-Fi mode WIFI

BLUETOOTH mode BT

󰟶

Display

Displays the product’s status and current mode.

D.IN  HDMI  Wi-Fi  BT

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and

change the TV speaker to External Speaker.

ENG - 8

Bottom Panel of the Soundbar

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

󰟳

󰟴

󰟵

󰟶 󰟷

󰟸

󰟹

󰟳

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device. (See page 27)

󰟴

SERVICE

Connect a USB storage device to upgrade the product's software.

󰟵

DC 19V (Power Supply In)

Connect the AC/DC power adapter. (See page 14)

󰟶

NETWORK

Press to connect to a wireless network (Wi-Fi) via the SmartThings app.

󰟷

ID SET

Press to connect the Soundbar to surround speakers and a subwoofer wirelessly. (The surround speaker is

sold separately.)

󰟸

HDMI

Inputs digital video and audio signals simultaneously using an HDMI cable.

Connect to the HDMI output of an external device. (See page 26)

󰟹

HDMI TO TV (eARC/ARC)

Connect to the HDMI jack on a TV. (See page 20)

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 9

03 USING THE SOUNDBAR REMOTE

CONTROL

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the back cover back into position.

How to Use the Remote Control

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

󰟳

󰟴

󰟵

󰟶

󰟷

󰟹

󰟸

󰟺

󰟼

󰟻

󰟳

Power

VOL WOOFER

SOUND

MODE

PAIR

Turns the Soundbar on and off.

• Auto Power Down Function

The unit turns off automatically in the

following situations:

– In D.IN / HDMI / Wi-Fi / BT mode if

there is no audio signal for 18 minutes.

󰟴

VOL WOOFER

SOUND

MODE

PAIR

Source

Press to select a source connected to the

Soundbar.

󰟵

Mute

VOL WOOFER

SOUND

MODE

PAIR

Press the (Mute) button to mute the

sound.

Press it again to unmute the sound.

ENG - 10

󰟶

SOUND MODE

VOL WOOFER

SOUND

MODE

PAIR

You can select the desired sound mode by choosing STANDARD, SURROUND, GAME

PRO, or ADAPTIVE SOUND.

• STANDARD

Outputs the original sound.

• SURROUND

Provides a wider sound eld than standard.

• GAME PRO

Provides stereoscopic sound to immerse you in the action while gaming.

• ADAPTIVE SOUND

Analyzes the content in real time and automatically provides the optimal sound eld

based on the characteristics of the content.

󰟷

VOL WOOFER

SOUND

MODE

PAIR

Bluetooth

PAIR

Switch the Soundbar to Bluetooth pairing mode. Press the button and wait for the “BT

PAIRING” screen to connect to a new Bluetooth device.

󰟸

Play / Pause

VOL WOOFER

SOUND

MODE

PAIR

You can also play or pause music by pressing the button.

󰟹

VOL WOOFER

SOUND

MODE

PAIR

Up/Down/

Left/Right

Press the indicated areas to select Up/Down/Left/Right.

Press Up/Down/Left/Right on the button to select or set functions.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select

the previous music le.

• ID SET

Use this option when the Subwoofer or Surround Speakers are not connected or need

reconnection.

While powered off, press and hold the Up button for 5 seconds to perform ID SET.

(See page 16.)

ENG - 11

󰟺

Sound Control

VOL WOOFER

SOUND

MODE

PAIR

When pressed, the setting items such as TREBLE, BASS, SYNC, CENTER LEVEL, FRONT

TOP LEVEL, and VIRTUAL ON/OFF are displayed in sequence. The desired item can be

adjusted using the Up/Down buttons.

– To control the volume of the treble or bass sound, select TREBLE or BASS in Sound

Settings, and then adjust the volume between -6~+6 by using the Up/Down buttons.

– Press and hold the (Sound Control) button for about 5 seconds to adjust the

sound for each frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and

10kHz are selectable using the Left/Right buttons and each can be adjusted to a

setting between -6 to +6 using the Up/Down buttons.

(Make sure the Sound mode is set to “STANDARD”.)

– To control the volume of the each speaker select CENTER LEVEL, or FRONT TOP

LEVEL in Sound Settings, and then adjust the volume between -6~+6 by using the

Up/Down buttons.

– If the video on the TV and audio from the Soundbar are not synchronised, select

SYNC in Sound Control, and then set the audio delay between 0~300 milliseconds by

using the Up/Down buttons.

– SYNC is only supported for some functions.

– If Surround Speakers are connected, select REAR LEVEL and then use the Up/Down

buttons to adjust the volume within a -6 to +6 range.

– The VIRTUAL Speaker function can be turned ON/OFF by using the Up/Down

buttons.

󰟻

VOL WOOFER

SOUND

MODE

PAIR

WOOFER

(BASS) LEVEL

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

Push the button up or down to adjust the level of the woofer (bass) to -12 or between -6

to +6. To set the woofer (bass) volume level to 0 (Default), press the button.

󰟼

VOL WOOFER

SOUND

MODE

PAIR

VOLUME

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

SOUND

MODE

VOL

WOOFER

SOUNDBAR

Push the button up or down to adjust the volume.

• Mute

Press the VOL button to mute the sound. Press it again to unmute the sound.

ENG - 12

Using the Hidden Buttons (Buttons with more than one function)

Hidden Button

Reference page

Remote Control Button Function

WOOFER (Up) TV remote control On/Off (Standby) page 13

Up ID SET page 16

(Sound Control)

7 Band EQ page 11

Outputspecicationsforthedifferentsoundeffectmodes

Effect Input

Output

With Subwoofer Only

With Subwoofer & Wireless

Rear Speaker Kit

STANDARD

2.0 ch 2.1 ch 2.1 ch

5.1 ch 3.1 ch 5.1 ch

SURROUND

2.0 ch 3.1.2 ch 5.1.2 ch

5.1 ch 3.1.2 ch 5.1.2 ch

GAME PRO

2.0 ch 3.1.2 ch 5.1.2 ch

5.1 ch 3.1.2 ch 5.1.2 ch

ADAPTIVE SOUND

2.0 ch 3.1.2 ch 5.1.2 ch

5.1 ch 3.1.2 ch 5.1.2 ch

• For input sources Dolby Atmos and DTS:X, the effect modes that can be selected using the

SOUND MODE button will not be available. (See above for the effect modes.)

• When the input source is Dolby Atmos®, the Subwoofer-only setup provides 3.1.2 channel audio,

while the Subwoofer & Wireless Rear Speaker Kit setup provides 5.1.2 channel audio.

• The Samsung Wireless Rear Speaker Kit can be purchased separately. To purchase a Kit or the

Subwoofer, contact the vendor you purchased the Soundbar from.

• The Surround Speakers will not produce sounds for 2 channel output while STANDARD mode is

in use. To enable sound for the Surround Speakers, change the effect mode to SURROUND.

ENG - 13

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

• This function can be used with IR remote controls only. Bluetooth remote controls (remote

controls that require pairing) are not supported.

• Set the TV speaker to External Speaker to use this function.

• Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

1. Turn Off the Soundbar.

2. Push up and hold the WOOFER button for 5 seconds.

Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the

following order: “SAMSUNG-TV REMOTE” (Default mode), “OFF-TV REMOTE”, “ALL-TV REMOTE”.

Remote Control Button Display Status

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

(Default mode)

SAMSUNG-TV REMOTE

Enable a Samsung TV’s IR remote

control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

OFF-TV REMOTE

Disable the TV remote control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

ALL-TV REMOTE

Enable a third-party TV’s IR remote

control.

ENG - 14

04 CONNECTING THE SOUNDBAR

Connecting the power and units

Use the power components to connect the Subwoofer and Soundbar to an electrical outlet in the following

order:

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

1. Connect the Power cord to the Subwoofer.

POWER

Rear of Subwoofer

Power Cord

2. First connect the power cable to the AC/DC adapter.

Connect the AC/DC adapter (with the power cable) to the Soundbar.

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

NETWORK ID SET

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

NETWORK ID SET

HDMI TO TV

(eARC/ARC)

HDMI IN

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

DIGITAL AUDIO IN

(OPTICAL)

SERVICE

DC 19V

HDMI

HDMI TO TV

(eARC/ARC)

Bottom of the Soundbar

Main Unit

DC 19V

AC/DC Adapter

Power Cord

3. Connect power to the Soundbar and Subwoofer. The Subwoofer is automatically connected when

the Soundbar is turned on.

Blue is On

ENG - 15

NOTES

• Connect the Subwoofer power before connecting to the Soundbar.

The Subwoofer will be automatically connected when turning on the Soundbar.

• If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on

automatically.

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

Manually connecting the Subwoofer

Before performing the manual connection procedure below:

• Check whether the power cables for the Soundbar and subwoofer are connected properly.

• Make sure that the Soundbar is turned off.

1. Turn off the Soundbar main.

2. Press and hold ID SET on the rear of the subwoofer for at least 5 seconds.

• The red indicator on the rear of the subwoofer turns off and the blue indicator blinks.

5 Sec

Rear of Subwoofer Rear of Subwoofer

Blinking blue

fast

ENG - 16

3. Press the Up button on the remote control for 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

ID SET

SOUND

MODE

PAIR

5 Sec

4. Check if the LINK LED is solid blue (connection complete).

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Subwoofer.

ENG - 17

LED Indicator Lights on the Rear of Subwoofer

LED Status Description Resolution

Blue

On

Successfully connected

(normal operation)

-

Blinking

Recovering the

connection

Check if the power cable attached

to the main Soundbar unit is

connected properly or wait about

5 minutes. If blinking persists, try

manually connecting the

subwoofer. See page 15.

Red

On

Standby (with the

Soundbar main unit

turned off)

Check if the power cable attached

to the main Soundbar unit is

connected properly.

Connection failed

Connect again. See the

instructions for manual

connection on page 15.

Red and blue

Blinking Malfunction

See the contact information for

the Samsung Service Centre in

this manual.

NOTES

• If the main unit is powered off, the wireless subwoofer will go into stand-by mode and the

STANDBY LED on the rear of the sub-woofer will turn red after blinking in blue several times.

• If you use a device that uses the same frequency (5.8GHz) as the Soundbar near the Soundbar,

interference may cause some sound interruption.

• The maximum transmission distance of the main unit’s wireless signal is about 10 m, but may vary

depending on your operating environment. If a steel-concrete or metallic wall is between the main

unit and the wireless subwoofer, the system may not operate at all because the wireless signal

cannot penetrate metal.

CAUTION

• Wireless receiving antennas are built into the wireless subwoofer. Keep the unit away from water

and moisture.

• For optimal listening performance, make sure that the area around the wireless subwoofer and the

Wireless Receiver Module (sold separately) is clear of any obstructions.

ENG - 18

Connecting an SWA-9000S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-9000S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– The speaker cables are colour coded.

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

• The LINK LED indicator (blue) on the Wireless Receiver Module should be blinking. If the

indicator does not blink, use a narrow pin to press and hold the ID SET button for 5 seconds or

longer. See the SWA-9000S user guide for more details.

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

STANDBY

LINK

STANDBY

LINK

Blue blinking

5 Sec

ENG - 19

3. Press the Up button on the remote control for 5 seconds.

• The ID SET message appears on the display of the Soundbar for a moment, and then it

disappears.

• The Soundbar will automatically power on when ID SET is complete.

ID SET

SOUND

MODE

PAIR

5 Sec

CAUTION

• If your Soundbar was playing music when it connects to the SWA-9000S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete).

STANDBY

LINK

STANDBY

LINK

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Receiver Module.

5. If the SWA-9000S is not connected, repeat the procedure from Step 2.

ENG - 20

05 USING A WIRED CONNECTION TO THE TV

Method 1. Connecting with HDMI

CAUTION

• When both the HDMI cable and optical cable are connected, the HDMI signal is received rst.

• To connect the HDMI cable between the TV and Soundbar, be sure to connect the terminals

marked ARC. Otherwise, the TV sound may not be output.

• Be sure to use the cable with the premium HDMI certication logo. In addition, make sure that

the cable is a certied Type A, high-speed HDMI Ethernet cable. (HIGH SPEED HDMI CABLE

WITH ETHERNET)

Connecting the TV that supports HDMI ARC (Audio Return Channel)

HDMI IN

(ARC)

HDMI TO TV

(eARC/ARC)

SERVICE

DC 19V

Connect to the HDMI IN

(ARC) port of your TV.

HDMI Cable

Bottom of the Soundbar

Connect to the HDMI TO TV

(eARC/ARC) port of the Soundbar

main unit.

Top of the Soundbar

TV ARC

1. With the Soundbar and TV turned off, connect the HDMI cable as shown in the gure.

2. Turn on the Soundbar and TV.

3. “TV ARC” appears in the display window of the Soundbar main unit and the Soundbar plays TV

sound.

• If TV sound is inaudible, press the (Source) button on the remote control or on the top of

the Soundbar to switch to “D.IN” mode. The screen displays “D.IN” and “TV ARC” in sequence,

and TV sound is played.

• When connecting a TV that supports the eARC function, “eARC” appears on the display and the

sound is heard.

Sayfa yükleniyor ...

Samsung HW-Q70T Kullanım kılavuzu

Samsung HW-Q70T Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler