Dell PowerEdge C5125 Hızlı başlangıç Kılavuzu

Dell PowerEdge C5125

Getting Started

With Your System

Začínáme se systémem

Guide de mise en route

Erste Schritte mit dem System

Τα πρώτα βήματα με το σύστημά σας

Rozpoczęcie pracy z systemem

Начало работы с системой

Procedimientos iniciales con el sistema

Sisteminizi Kullanmaya Başlarken

תכרעמה םע הדובעה תליחת

Dell PowerEdge C5125

Getting Started

With Your System

Regulatory Model: B04S

Notes, Cautions, and Warnings

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell

™

, the DELL logo, and PowerEdge

™

are trademarks of Dell Inc.

AMD

®

, AMD Phenom

™

, and AMD Athlon

™

are trademarks of Advanced Micro Devices, Inc.

Microsoft

®

and Windows

®

are either trademarks or registered trademarks of Microsoft Corporation

in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise Linux

®

are registered

trademarks of Red Hat, Inc. in the United States and/or other countries. SUSE™ is a trademark of

Novell Inc. in the United States and other countries. Citrix

®

, Xen

®

, and XenServer

®

are either

registered trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries.

VMware

®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model B04S

March 2011 P/N R5VKT Rev. A00

NOTE: A note indicates important information that will help a user make better use

of a computer system.

CAUTION: A caution indicates potential damage to hardware or loss of data is

instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

Installation and Configuration 3

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions

apply:

• Access can only be gained by service persons or by users who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

• Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

CAUTION: Restricted Access Location

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To avoid

personal injury or damage to the system, you must adequately support the system

during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack equipment

must provide sufficient airflow to the system to maintain proper cooling.

CAUTION: When installing rails in a square-hole rack it is important to ensure

that the square peg slides through the square holes.

CAUTION: Square studs must be flush with the rack posts to install properly.

4 Installation and Configuration

1

Pull on the latch release buttons on the end piece midpoints to open the

rail latches.

2

Align the end pieces of the rails on the vertical rack flanges to seat the pegs

in the bottom hole of the first U and the top hole of the second U. Engage

the back end of the rail until the latch locks in place.

NOTE: The rails can be used in both square-hole and round-hole racks.

Front

Back

Installation and Configuration 5

3

Insert the cage nut on the rack.

4

Repeat steps 1 to 4 to position and seat the front end piece on the vertical

flange.

NOTE: To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

6 Installation and Configuration

Installing the System

Empty the System Chassis

1

Unplug the power cable from the power supply unit.

.

2

Pull out the power supply unit handle.

Installation and Configuration 7

3

Press down on the release latch



.

4

Pull the power supply unit out of the system



.

5

Press the release latch down



and pull the sled out of the system



.

8 Installation and Configuration

Install the System Into the Rack

1

Slide the system into the rack.

2

If present, remove the chassis stabilizer shipping bracket (optional) from

the rack.

3

Tighten the captive thumbscrews to secure the ears of the system to the

front of the rack.

4

Install the stopping bracket on the post and secure with M5 screws.

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

NOTE: To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

NOTE: Make sure the latch release mechanism is engaged correctly.

Installation and Configuration 9

Populate the System

1

Push the power supply unit into the system until flush with the case and

the release latch locks.

2

Close the power supply unit handle.

10 Installation and Configuration

3

Plug the chassis power cable into the power supply unit.

NOTE: The correct configuration of the integral chassis AC power cables to the

PSU sockets is as shown in the following illustration.

PSU1 PSU2

Installation and Configuration 11

4

Install the sleds. Push the sled into the system until flush with the case and

the release latch locks.

Connecting the Keyboard, Mouse, and Monitor

The connector on the front of your system has an icon indicating which cable

to plug in. Connect a keyboard, mouse, or monitor (optional).

12 Installation and Configuration

Connecting the Power Cables

1

On the back of the system, connect the mains power cable to the system’s

power socket.

2

Plug the other end of the power cables into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply or a power

distribution unit.

Turning On the System

When connected to a power source the system automatically powers on.

See the Using the Baseboard Management Controller Guide at

support.dell.com/manuals.

NOTE:

AC Port 1 provides power to PSU1, ACP Port 2 provides power to PSU2. See

Populate the System step 3 for further information.

AC Port 2

AC Port 1

Installation and Configuration 13

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the

operating system is installed before installing hardware or software not

purchased with the system.

Supported Operating Systems

• Microsoft Windows Server 2008 Enterprise Edition Release 2 (64-bit)

• Microsoft Windows HPC 2008 Release 2

• Microsoft HyperV

• Red Hat Enterprise Linux 6.0 (64-bit)

• SUSE Linux Enterprise Server 11 SP1 (64-bit)

• Citrix XenServer Enterprise Edition 5.6

Other Information You May Need

See the Hardware Owner’s Manual for information about system features,

troubleshooting, and component replacement. This document is available at

support.dell.com/manuals

.

See the Using the Baseboard Management Controller Guide at

support.dell.com/manuals.

NOTE:

For the latest information on supported operating systems, see

support.dell.com.

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

NOTE: Always check for updates and read the updates first because they often

supersede information in other documents.

14 Technical Specifications

Technical Specifications

Processor (Per System Board)

Processor type AMD Phenom II 910e, 2.6 GHz, 4 core

AMD Athlon II 610E, 2.4 GHz, 4 core

AMD Athlon II 260U, 1.6 GHz, 2 core

Expansion Bus (Per System Board)

Bus type PCI-E x1 connector for sideband signal

Internal PCIe Bus 1, SR5650(GPP3): PCI-E

x2,x1,x1,x1,x1,x4

3, SP5100: PCI 32/33

Memory (Per System Board)

Architecture UDDR3-1333

Memory module sockets 4 Quad Channel Unbuffered DDR3

800/1066/1333

Memory module capacities

Minimum RAM 2 GB

Maximum RAM 16 GB

Drives (Per System Board)

Hard drives SATAII (4 channels) support:

• 3.5" HDD x2 (Max Capacity 2 TB per

drive)

• 2.5" HDD x4 (Max Capacity 500 GB

per drive), SSD

Connectors (Per System Board)

Back

NIC

2

Serial (internal)

1

USB (through Y-cable)

2

Video (through Y-cable)

1

KVM over IP Port

1

Technical Specifications 15

Video

Video type AST2050

Video memory 128 MB DDR2 SDRAM

Power

AC power supply (per power supply)

Wattage

1400 W

Voltage

200-240 VAC, 50/60 Hz, 9.6 A max

Heat dissipation

47.65 BTU/hr max

Maximum inrush current

55 A max

Physical

Sled system dimension (with 3.5" HDD)

Standard sled size:

613.3 mm x 124 mm x 42.45 mm

(8 sled)

VLP sled size:

613.3 mm x 124 mm x 27.7 mm

(12 sled)

Mainboard

1

Hard drives (3.5")

2

Hard drive board (3.5")

1

Sled system dimension (with 2.5" HDD)

Standard sled size:

613.3 mm x 124 mm x 42.45 mm

(8 sled)

VLP sled size:

613.3 mm x 124 mm x 27.7 mm

(12 sled)

Mainboard

1

Hard drives (2.5")

4

Hard drive board (3.5")

1

16 Technical Specifications

Chassis

Height

13 cm (5.1 in.)

Width

44.7 cm (17.6 in.)

Depth

75 cm (29.5 in.)

Weight (loaded: maximum weight)

8 sled configuration:

45 kg (99.21 lbs.)

12 sled configuration:

51.22 kg (112.92 lbs.)

Weight (empty)

8 sled configuration:

18.3 kg (40.34 lbs.)

12 sled configuration:

19.3 kg (42.55 lbs.)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see the dell.com/environmental_datasheets.

Temperature

Operating

10° to 35°C (50°F to 95°F) with a maximum

temperature gradation of 10°C (per hour

Airflow at maximum fan speed

(CFM) at peak temperature

140 CFM (8 sled)

285 CFM (12 sled)

Airflow at nominal fan speed (CFM)

at nominal temperature

40 CFM (8 sled)

60 CFM (12 sled)

Storage

–40° to 65°C (40°F to 149°F) with a

maximum temperature gradation of 20°C

per hour

Relative Humidity

Operating

20% to 80% (noncondensing) with a

maximum humidity gradation of 10%

per hour

Storage

5% to 95% (noncondensing)

Technical Specifications 17

Environmental (continued)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.87 Grms at 10–500 Hz for 15 min

Maximum shock

Operating

One shock pulse in the positive z axis (one

pulse on each side of the system) of 31 G for

2.6 ms in the operational orientation

Storage

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

71 G for up to 2 ms.

Six consecutively executed shock pulses in

the positive and negative x, y, and z axes

(one pulse on each side of the system) of

22 G faired square wave pulse with velocity

change at 200 inches/second

Altitude

Operating

-16 to 3,048 m (-50 to 10,000 ft.)

NOTE: For altitudes above 2,950 feet, the

maximum operating temperature s derated to

1°F/550 ft.

Storage

-16 to 10, 600 m (-50 to 35,000 ft.)

Airborne Contaminant Level

Class

G2 or lower as defined by ISA-S71.04-1985

18 Technical Specifications

Sayfa yükleniyor ...

Dell PowerEdge C5125 Hızlı başlangıç Kılavuzu

Dell PowerEdge C5125 Hızlı başlangıç Kılavuzu

Diğer dillerde

İlgili Makaleler

Dell PowerEdge C5125 Hızlı başlangıç ​​Kılavuzu

Dell PowerEdge C5125 Hızlı başlangıç ​​Kılavuzu

Diğer dillerde

İlgili Makaleler

Dell PowerEdge C5125 Hızlı başlangıç Kılavuzu

Dell PowerEdge C5125 Hızlı başlangıç Kılavuzu