Husqvarna 122HD60 El kitabı

122HD45

122HD60

GB Operator’s manual 2-20

SE Bruksanvisning 21-39

DK Brugsanvisning 40-58

FI Käyttöohje 59-77

DE Bedienungsanweisung 78-97

FR Manuel d’utilisation 98-117

NL Gebruiksaanwijzing 118-137

ES Manual de instrucciones 138-157

PT Instruções para o uso 158-177

IT Istruzioni per l’uso 178-197

RU óêîâîäñòâî ïî

ýêñïëóàòàöèè 198-218

BG úêîâîäñòâî çà

åêñïëîàòàöèß 219-237

RO Instrucöiuni de utilizare 238-257

GR √‰ËÁ›Â˜ ¯Ú‹ÛÂˆ˜ 258-277

EE Käsitsemisõpetus 278-295

LV Lieto‰anas pamÇc¥ba 296-314

LT Naudojimosi instrukcijos 315-333

CZ Návod k pouÏití 334-353

SK Návod na obsluhu 354-372

PL Instrukcja obs∏ugi 373-392

HU Használati utasítás 393-412

HR Priruãnik 413-431

NO Bruksanvisning 432-451

SI

Navodila za uporabo

452-470

BA

Uputstvo o upotrebi 471- 490

RS

Priruãnik 491- 510

TR

Kullanım kılavuzu 511- 530

H1153993-26,122HD45,60,#6DE7.fm Page 1 Friday, March 2, 2012 10:05 AM

KEY TO SYMBOLS

2 – English

Symbols

WARNING! Incorrect or careless use of a

hedge trimmer can turn it into a

dangerous tool that can cause serious or

even fatal injury. It is extremely important

that you read and understand the

contents of this operator’s manual.

Please read the operator’s manual

carefully and make sure you

understand the instructions before

using the machine.

Always wear:

• Approved hearing protection

• Approved eye protection

This product is in accordance with

applicable EC directives.

Always wear approved protective gloves.

Wear sturdy, non-slip boots or shoes.

Noise emission to the environment

according to the European Community’s

Directive. The machine’s emission is

speciﬁed in chapter Technical data and on

label.

Starting instructions See

the instructions under the

heading Start and stop.

Other symbols/decals on the machine refer to special

certiﬁcation requirements for certain markets.

The engine is switched off by moving the

stop switch to the stop position.

CAUTION! The stop switch

automatically returns to the start

position. In order to prevent

unintentional starting, the spark plug

cap must be removed from the spark

plug when assembling, checking and/or

performing maintenance.

Always wear approved protective

gloves.

Regular cleaning is required.

Visual check.

Protective goggles or a visor must be

worn.

H1153993-26,122HD45,60#4ACBF.fm Page 2 Tuesday, January 4, 2011 8:31 AM

CONTENTS

English – 3

Contents Note the following before starting:

Please read the operator’s manual carefully.

KEY TO SYMBOLS

Symbols ................................................................ 2

CONTENTS

Contents ............................................................... 3

Note the following before starting: ........................ 3

INTRODUCTION

Dear Customer, .................................................... 4

WHAT IS WHAT?

What is what? ....................................................... 5

GENERAL SAFETY PRECAUTIONS

Important .............................................................. 6

Personal protective equipment ............................. 6

Machine′s safety equipment ................................. 7

FUEL HANDLING

Fuel safety ............................................................ 10

Fuel ...................................................................... 10

Fuelling ................................................................. 11

STARTING AND STOPPING

Check before starting ........................................... 12

Starting and stopping ........................................... 12

WORKING TECHNIQUES

General working instructions ................................ 14

MAINTENANCE

Carburettor ........................................................... 16

Mufﬂer .................................................................. 16

Cooling system ..................................................... 16

Spark plug ............................................................ 16

Air ﬁlter ................................................................. 17

Gear ..................................................................... 17

Cutting unit ........................................................... 17

Cleaning and lubrication ....................................... 17

Maintenance schedule ......................................... 18

TECHNICAL DATA

Technical data ...................................................... 19

EC-declaration of conformity ................................ 20

!

WARNING! Long-term exposure to noise

can result in permanent hearing

impairment. So always use approved

hearing protection.

!

WARNING! Under no circumstances may

the design of the machine be modiﬁed

without the permission of the

manufacturer. Always use genuine

accessories. Non-authorized

modiﬁcations and/or accessories can

result in serious personal injury or the

death of the operator or others.

!

WARNING! Incorrect or careless use of a

hedge trimmer can turn it into a

dangerous tool that can cause serious or

even fatal injury. It is extremely important

that you read and understand the

contents of this operator’s manual.

H1153993-26,122HD45,60#4ACBF.fm Page 3 Tuesday, January 4, 2011 8:31 AM

4 – English

INTRODUCTION

Dear Customer,

Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,

when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production

of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-

powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot of different products,

from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the ﬁrst motor

driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.

Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our

highest priority. The business concept is to develop, manufacture and market motor driven products for forestry and

gardening as well as for building and construction industry. Husqvarna

′

s aim is also to be in the front edge according to

ergonomics, usability, security and environmental protection. That is the reason why we have developed many different

features to provide our products within these areas.

We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very

long time to come. The purchase of one of our products gives you access to professional help with repairs and service

whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the

address of your nearest service workshop.

It is our wish that you will be satisﬁed with your product and that it will be your companion for a long time. Think of this

operator

′

s manual as a valuable document. By following its

′

content (using, service, maintenance etc) the life span and

the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get

the operator

′

s manual.

Thank you for using a Husqvarna product.

Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and

appearance of products without prior notice.

H1153993-26,122HD45,60#4ACBF.fm Page 4 Tuesday, January 4, 2011 8:31 AM

English – 5

WHAT IS WHAT?

What is what?

1 Operator′s manual

2 Handle

3 Throttle lock

4 Fuel cap

5 Choke control

6 Front handle

7 Blade and blade guard

8 Transport guard

9 Air ﬁlter cover

10 Air purge

11 Fuel tank

12 Lock for handle 122HD60

13 Throttle control

14 Spark plug cap and spark plug

15 Cylinder cover

16 Starter handle

17 Stop switch

18 Lubricant ﬁller cap, gear

19 Gear

20 Hand guard

21 Combination spanner

22 Tube of grease

H1153993-26,122HD45,60#4ACBF.fm Page 5 Tuesday, January 4, 2011 8:31 AM

GENERAL SAFETY PRECAUTIONS

6 – English

Important Personal protective equipment

HEARING PROTECTION

Wear hearing protection that provides adequate noise

reduction.

EYE PROTECTION

Always wear approved eye protection. If you use a visor

then you must also wear approved protective goggles.

Approved protective goggles must comply with standard

ANSI Z87.1 in the USA or EN 166 in EU countries.

GLOVES

Gloves should be worn when necessary, e.g., when ﬁtting

cutting attachments.

BOOTS

Wear sturdy, non-slip boots or shoes.

IMPORTANT!

The machine is only designed for cutting branches and

twigs.

Never use a machine that has been modiﬁed in any way

from its original speciﬁcation.

Never use the machine if you are tired, if you have drunk

alcohol, or if you are taking medication that could affect

your vision, your judgement or your co-ordination.

Wear personal protective equipment. See instructions

under the heading ”Personal protective equipment”.

Never use the machine in extreme weather conditions

such as severe cold, very hot and/or humid climates.

Never use a machine that is faulty. Carry out the checks,

maintenance and service instructions described in this

manual. Some maintenance and service measures

must be carried out by trained and qualiﬁed specialists.

See instructions under the heading Maintenance.

All covers and guards must be ﬁtted before starting.

Ensure that the spark plug cap and ignition lead are

undamaged to avoid the risk of electric shock.

!

WARNING! This machine produces an

electromagnetic ﬁeld during operation.

This ﬁeld may under some

circumstances interfere with active or

passive medical implants. To reduce the

risk of serious or fatal injury, we

recommend persons with medical

implants to consult their physician and

the medical implant manufacturer before

operating this machine.

!

WARNING! Running an engine in a

conﬁned or badly ventilated area can

result in death due to asphyxiation or

carbon monoxide poisoning.

!

WARNING! Never allow children to use or

be in the vicinity of the machine. As the

machine is equipped with a spring-

loaded stop switch and can be started by

low speed and force on the starter

handle, even small children under some

circumstances can produce the force

necessary to start the machine. This can

mean a risk of serious personal injury.

Therefore remove the spark plug cap

when the machine is not under close

supervision.

!

WARNING! Faulty blades can increase

the risk of accidents.

IMPORTANT!

Incorrect or careless use of a hedge trimmer can turn it

into a dangerous tool that can cause serious or even

fatal injury. It is extremely important that you read and

understand the contents of this operator’s manual.

You must use approved personal protective equipment

whenever you use the machine. Personal protective

equipment cannot eliminate the risk of injury but it will

reduce the degree of injury if an accident does happen.

Ask your dealer for help in choosing the right equipment.

!

WARNING! Listen out for warning signals

or shouts when you are wearing hearing

protection. Always remove your hearing

protection as soon as the engine stops.

H1153993-26,122HD45,60#4ACBF.fm Page 6 Tuesday, January 4, 2011 8:31 AM

GENERAL SAFETY PRECAUTIONS

English – 7

CLOTHING

Wear clothes made of a strong fabric and avoid loose

clothing that can catch on twigs and branches. Always

wear heavy, long pants. Do not wear jewellery, shorts

sandals or go barefoot. Secure hair so it is above shoulder

level.

FIRST AID KIT

Always have a ﬁrst aid kit nearby.

Machine′s safety equipment

This section describes the machine′s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly. See the

”What is what?” section to locate where this equipment is

positioned on your machine.

The life span of the machine can be reduced and the risk

of accidents can increase if machine maintenance is not

carried out correctly and if service and/or repairs are not

carried out professionally. If you need further information

please contact your nearest service workshop.

Throttle lockout

The throttle lockout is designed to prevent accidental

operation of the throttle control. When you press the lock

(A) (i.e. when you grasp the handle) it releases the throttle

control (B). When you release the handle the throttle

control and the throttle lockout both move back to their

original positions. This movement is controlled by two

independent return springs. This arrangement means that

the throttle control is automatically locked at the idle

setting.

Make sure the throttle control is locked at the idle setting

when the throttle lockout is released.

Press the throttle lockout and make sure it returns to its

original position when you release it.

Check that the throttle control and throttle lockout move

freely and that the return springs work properly.

See instructions under the heading Start. Start the hedge

trimmer and apply full throttle. Release the throttle trigger

and check that the blades stop and remain stationary. If

the blades move when the throttle trigger is in the idle

position then the carburettor idle setting must be adjusted.

See instructions under the heading Maintenance.

Stop switch

Use the stop switch to switch off the engine.

Start the engine and make sure the engine stops when

you move the stop switch to the stop setting. The stop

switch automatically returns to the start position. In order

to prevent unintentional starting, the spark plug cap must

be removed from the spark plug when assembling,

checking and/or performing maintenance.

IMPORTANT!

All servicing and repair work on the machine requires

special training. This is especially true of the machine

′

s

safety equipment. If your machine fails any of the checks

described below you must contact your service agent.

When you buy any of our products we guarantee the

availability of professional repairs and service. If the

retailer who sells your machine is not a servicing dealer,

ask him for the address of your nearest service agent.

!

WARNING! Never use a machine with

faulty safety equipment. The machine’s

safety equipment must be checked and

maintained as described in this section. If

your machine fails any of these checks

contact your service agent to get it

repaired.

H1153993-26,122HD45,60#4ACBF.fm Page 7 Tuesday, January 4, 2011 8:31 AM

GENERAL SAFETY PRECAUTIONS

8 – English

Hand guard

The hand guard prevents hands from coming into contact

with the moving blades, for example, if the operator loses

grip on the front handle.

Check that the hand guard is ﬁtted correctly.

Check that the hand guard is undamaged.

Vibration damping system

Your machine is equipped with a vibration damping

system that is designed to minimize vibration and make

operation easier.

The machine′s vibration damping system reduces the

transfer of vibration between the engine unit/cutting

equipment and the machine

′

s handle unit.

The engine body, including the blades, is suspended on

the handlebar using four rubber bushings.

Regularly check the vibration damping units for cracks or

deformation. Check that the vibration damping element is

undamaged and securely attached.

Mufﬂer

The mufﬂer is designed to keep noise levels to a minimum

and to direct exhaust fumes away from the user. A mufﬂer

ﬁtted with a catalytic converter is also designed to reduce

harmful exhaust gases.

In countries that have a warm and dry climate there is a

signiﬁcant risk of ﬁre. We therefore ﬁt certain mufﬂers with

a spark arrestor mesh. Check whether the mufﬂer on your

machine is ﬁtted with this kind of mesh.

For mufﬂers it is very important that you follow the

instructions on checking, maintaining and servicing your

machine.

Never use a machine that has a faulty mufﬂer.

Regularly check that the mufﬂer is securely attached to

the machine.

If the mufﬂer on your machine is ﬁtted with a spark

arrestor mesh this must be cleaned regularly. A blocked

mesh will cause the engine to overheat and may lead to

serious damage.

!

WARNING! Overexposure to vibration

can lead to circulatory damage or nerve

damage in people who have impaired

circulation. Contact your doctor if you

experience symptoms of overexposure

to vibration. Such symptoms include

numbness, loss of feeling, tingling,

pricking, pain, loss of strength, changes

in skin colour or condition. These

symptoms normally appear in the

ﬁngers, hands or wrists. The risk

increases at low temperatures.

!

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

H1153993-26,122HD45,60#4ACBF.fm Page 8 Tuesday, January 4, 2011 8:31 AM

GENERAL SAFETY PRECAUTIONS

English – 9

Blade and blade guard

The outer part of the blades (1) are shaped as blade

guards. The blade guard is intended to protect against

any part of the body coming into contact with the blades.

Check that the blade guard is not damaged or distorted.

Replace the cutting unit if it is bent or damaged.

Gear

The gear housing gets hot when the machine has been in

use. To avoid burning yourself do not touch the gear

housing.

!

WARNING! The inside of the mufﬂer

contain chemicals that may be

carcinogenic. Avoid contact with these

elements in the event of a damaged

mufﬂer.

!

WARNING! Bear in mind that: The

exhaust fumes from the engine are hot

and may contain sparks which can start

a ﬁre. Never start the machine indoors or

near combustible material!

H1153993-26,122HD45,60#4ACBF.fm Page 9 Tuesday, January 4, 2011 8:31 AM

FUEL HANDLING

10 – English

Fuel safety

Never start the machine:

1 If you have spilt fuel on it. Wipe off the spillage and

allow remaining fuel to evaporate.

2 If you have spilt fuel on yourself or your clothes,

change your clothes. Wash any part of your body that

has come in contact with fuel. Use soap and water.

3 If the machine is leaking fuel. Check regularly for

leaks from the fuel cap and fuel lines.

Transport and storage

• Store and transport the machine and fuel so that there

is no risk of any leakage or fumes coming into contact

with sparks or naked ﬂames, for example, from

electrical machinery, electric motors, electrical relays/

switches or boilers.

• When storing and transporting fuel always use

approved containers intended for this purpose.

• When storing the machine for long periods the fuel

tank must be emptied. Contact your local petrol

station to ﬁnd out where to dispose of excess fuel.

• Ensure the machine is cleaned and that a complete

service is carried out before long-term storage.

• The transport guard must always be ﬁtted to the

cutting attachment when the machine is being

transported or in storage.

• Secure the machine during transport.

Fuel

CAUTION! The machine is equipped with a two-stroke

engine and must always been run using a mixture of

petrol and two-stroke oil. It is important to accurately

measure the amount of oil to be mixed to ensure that the

correct mixture is obtained. When mixing small amounts

of fuel, even small inaccuracies can drastically affect the

ratio of the mixture.

Petrol

CAUTION! Always use a quality petrol/oil mixture at least

90 octane (RON). If your machine is equipped with a

catalytic converter (see chapter on Technical data) always

use a good quality unleaded petrol/oil mixture. Leaded

petrol will destroy the catalytic converter.

Use low-emission petrol, also known as alkylate petrol, if

it is available.

• The lowest octane recommended is 90 (RON). If you

run the engine on a lower octane grade than 90 so-

called knocking can occur. This gives rise to a high

engine temperature, which can result in serious

engine damage.

• When working at continuous high revs a higher octane

rating is recommended.

Two-stroke oil

• For best results and performance use HUSQVARNA

two-stroke engine oil, which is specially formulated for

our air-cooled two-stroke engines.

• Never use two-stroke oil intended for water-cooled

engines, sometimes referred to as outboard oil (rated

TCW).

• Never use oil intended for four-stroke engines.

• A poor oil quality and/or too high oil/fuel ratio may

jeopardise function and decrease the life time of

catalytic converters.

• Mixing ratio

1:50 (2%) with HUSQVARNA two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB

formulated for air-cooled, two-stroke engines.

!

WARNING! Take care when handling fuel.

Bear in mind the risk of ﬁre, explosion

and inhaling fumes.

!

WARNING! Fuel and fuel fumes are

highly inﬂammable and can cause

serious injury when inhaled or allowed to

come in contact with the skin. For this

reason observe caution when handling

fuel and make sure there is adequate

ventilation.

Petrol, litre

Two-stroke oil, litre

2% (1:50) 3% (1:33)

5 0,10 0,15

10 0,20 0,30

15 0,30 0,45

20 0,40 0,60

H1153993-26,122HD45,60#4ACBF.fm Page 10 Tuesday, January 4, 2011 8:31 AM

FUEL HANDLING

English – 11

Mixing

• Always mix the petrol and oil in a clean container

intended for fuel.

• Always start by ﬁlling half the amount of the petrol to

be used. Then add the entire amount of oil. Mix

(shake) the fuel mixture. Add the remaining amount of

petrol.

• Mix (shake) the fuel mixture thoroughly before ﬁlling

the machine’s fuel tank.

• Do not mix more than one month’s supply of fuel at a

time.

• If the machine is not used for some time the fuel tank

should be emptied and cleaned.

Fuelling

• Always use a fuel container with an anti-spill valve.

• Clean the area around the fuel cap. Contamination in

the tank can cause operating problems.

• Ensure that the fuel is well mixed by shaking the

container before ﬁlling the tank.

!

WARNING! The catalytic converter

mufﬂer gets very hot during and after

use. This also applies during idling. Be

aware of the ﬁre hazard, especially when

working near ﬂammable substances and/

or vapours.

!

WARNING! Taking the following

precautions, will lessen the risk of ﬁre:

Do not smoke or place hot objects near

fuel.

Always shut off the engine before

refuelling.

Refuel in a well ventilated area. Never

fuel the machine indoors.

Always stop the engine and let it cool for

a few minutes before refuelling.

When refuelling, open the fuel cap slowly

so that any excess pressure is released

gently.

Tighten the fuel cap carefully after

refuelling.

Always move the machine away from the

refuelling area and source before

starting.

H1153993-26,122HD45,60#4ACBF.fm Page 11 Tuesday, January 4, 2011 8:31 AM

STARTING AND STOPPING

12 – English

Check before starting

• Inspect the working area. Remove any objects that

could be thrown out.

• Check the cutting attachment. Never use blades that

are dull, cracked or damaged.

• Check that the machine is in perfect working order.

Check that all nuts and screws are tight.

• Make sure the gear housing is lubricated correctly.

See instructions under the heading Gear housing.

• Check that the cutting attachment always stops when

the engine is idling.

• Only use the machine for the purpose it was intended

for.

• Make sure that the handle and safety features are in

good working order. Never use a machine that lacks a

part or has been modiﬁed outside its speciﬁcations.

• All covers must be correctly ﬁtted and undamaged

before you start the machine.

Starting and stopping

Cold engine

Choke:

Set the choke control in the choke position.

Primer bulb: Press the air purge diaphragm repeatedly

until fuel begins to ﬁll the diaphragm (about 6 times). The

diaphragm need not be completely ﬁlled.

Starting

Hold the body of the machine on the ground using your

left hand (CAUTION! Not with your foot!). Grip the starter

handle, slowly pull out the cord with your right hand until

you feel some resistance (the starter pawls grip), now

quickly and powerfully pull the cord. Never twist the

starter cord around your hand.

Push the choke control back to its original position as

soon as the engine ﬁres, and continue trying to start until

the engine starts.

CAUTION! When the choke control is pushed back to its

original position, the engine runs at a heightened speed,

the so called start throttle position, and the blades then

move. Start throttle position is released by throttling using

the throttle lever.

CAUTION! Do not pull the starter cord all the way out and

do not let go of the starter handle when the cord is fully

extended. This can damage the machine.

!

WARNING! The complete gear housing

must be ﬁtted before the machine is

started, otherwise the clutch may loosen

and cause personal injury.

Always move the machine about 3

metres from the refuelling position

before starting. Place the machine on a

ﬁrm surface. Remember that the blades

may start to move when the engine is

started. Make sure the blades cannot

come into contact with any object. Make

sure that no unauthorised persons are in

the working area, otherwise there is a

risk of serious personal injury. The safety

distance is 15 metres.

H1153993-26,122HD45,60#4ACBF.fm Page 12 Tuesday, January 4, 2011 8:31 AM

STARTING AND STOPPING

English – 13

Warm engine

Hold the body of the machine on the ground using your

left hand (CAUTION! Not with your foot!). Grip the starter

handle, slowly pull out the cord with your right hand until

you feel some resistance (the starter pawls grip), now

quickly and powerfully pull the cord. Never twist the

starter cord around your hand.

Stopping

The engine is switched off by moving the stop switch to

the stop position.

CAUTION!

The stop switch automatically returns to the start position.

In order to prevent unintentional starting, the spark plug

cap must be removed from the spark plug when

assembling, checking and/or performing maintenance.

H1153993-26,122HD45,60#4ACBF.fm Page 13 Tuesday, January 4, 2011 8:31 AM

WORKING TECHNIQUES

14 – English

General working instructions

Safety instructions regarding the

surroundings

• Never allow children to use the machine.

• Observe your surroundings and make sure that there

is no risk of people or animals coming into contact

with the cutting equipment.

• Ensure that no-one comes closer than 15 m while you

are working.

• Never allow anyone else to use the machine without

ﬁrst ensuring that they have understood the contents

of the operator’s manual.

• Never work from a ladder, stool or any other raised

position that is not fully secured.

• Keep in mind that the operator is responsible for

accidents or hazards occuring to other people or their

property.

Safety instructions while working

• Always ensure you have a safe and stable working

position.

• Never leave the machine unsupervised with the motor

running.

• Always use both hands to hold the machine. Hold the

machine in front of your body.

• Make sure that your hands and feet do not come near

the cutting attachment when the engine is running.

• When the engine is switched off, keep your hands and

feet away from the cutting attachment until it has

stopped completely.

• Watch out for stumps of branches that can be thrown

out during cutting.

• Do not cut too close to the ground. Stones and other

objects can be thrown out.

• Check the working area for foreign objects such as

electricity cables, insects and animals, etc, or other

objects that could damage the cutting attachment,

such as metal items.

• If any foreign object is hit or if vibrations occur stop the

machine immediately. Disconnect the HT lead from

the spark plug. Check that the machine is not

damaged. Repair any damage.

• If anything jams in the blades while you are working,

switch off the engine and wait until it has stopped

completely before cleaning the blades. Disconnect the

HT lead from the spark plug.

IMPORTANT!

This section takes up the basic safety precautions for

working with a hedge trimmer.

If you encounter a situation where you are uncertain

how to proceed you should ask an expert. Contact your

dealer or your service workshop.

Avoid all usage which you consider to be beyond your

capability.

!

WARNING! The machine can cause

serious personal injury. Read the safety

instructions carefully. Learn how to use

the machine.

!

WARNING! Cutting tool. Do not touch the

tool without ﬁrst switching off the

engine.

H1153993-26,122HD45,60#4ACBF.fm Page 14 Tuesday, January 4, 2011 8:31 AM

WORKING TECHNIQUES

English – 15

If the blades get stuck, they can be loosened by

sticking the combination spanner into the gear

housing. Remove the lubricant plug and stick the

combination spanner into the gearing and turn it back

and forth.

Safety instructions after completing work

• The transport guard should always be ﬁtted to the

cutting attachment when the machine is not in use.

• Make sure the cutting attachment has stopped before

cleaning, carrying out repairs or an inspection.

Disconnect the HT lead from the spark plug.

• Always wear heavy-duty gloves when repairing the

cutting attachment. This is extremely sharp and can

easily cause cuts.

• Store the machine out of reach of children.

• Use only original spare parts for repairs.

Basic working techniques

• Work with a swinging action from the bottom upwards

when trimming sides.

• Adjust the throttle setting to suit the load.

• When trimming a hedge the engine should always

face away from the hedge.

• Hold the machine as close to your body as possible to

get the best balance.

• Make sure that the tip does not touch the ground.

• Do not rush the work, but work steadily until all the

branches have been cut back cleanly.

122HD60

The hedge trimmer’s rear handle can be set in ﬁve

positions by pulling out the catch. See ﬁgure. When the

handle is adjusted, the hedge trimmer must be idling or

not running.

• While working the handle should always be facing

upwards irrespective of how the hedge trimmer is

directed.

H1153993-26,122HD45,60#4ACBF.fm Page 15 Tuesday, January 4, 2011 8:31 AM

MAINTENANCE

16 – English

Carburettor

Adjustment of the idle speed

Before any adjustments are made, make sure that the air

ﬁlter is clean and the air ﬁlter cover is ﬁtted. Make sure the

start throttle position is disengaged.

Adjust the idle speed using the idle adjustment screw T, if it

is necessary to readjust. First turn the T screw clockwise until

the cutting attachment starts to move. Then turn the screw

anticlockwise until the cutting attachment stops. The idle

speed is correctly adjusted when the engine runs smoothly

in every position. The idle speed should also be well below

the speed at which the cutting attachment starts to move.

Rec. idle speed: See the Technical data section.

Mufﬂer

CAUTION! Some mufﬂers are ﬁtted with a catalytic

converter. See chapter on Technical data to see whether

your machine is ﬁtted with a catalytic converter.

The mufﬂer is designed to reduce the noise level and to

direct the exhaust gases away from the operator. The

exhaust gases are hot and can contain sparks, which may

cause ﬁre if directed against dry and combustible material.

Some mufﬂers are equipped with a special spark arrestor

mesh. If your machine has this type of mufﬂer, the mesh must

be cleaned. This is best done with a wire brush.

On mufﬂers without a catalytic converter, the mesh should be

cleaned or replaced if necessary once a week. If the mesh

is damaged it must be replaced. If the mesh is frequently

blocked, this can be a sign that the carburettor is incorrectly

adjusted or that too much oil has been mixed with the petrol.

On mufﬂers ﬁtted with a catalytic converter, the mesh

must be checked, and if necessary cleaned, monthly. If

the mesh is damaged it must be replaced. If the mesh

is frequently blocked, this can be a sign that the

performance of the catalytic converter is impaired.

Contact your dealer to inspect the mufﬂer. A blocked

mesh will cause the machine to overheat and result in

damage to the cylinder and piston.

CAUTION! Never use a machine with a defective mufﬂer.

Cooling system

To keep the working temperature as low as possible the

machine is equipped with a cooling system.

The cooling system consists of:

1 Cooling ﬁns on the cylinder.

2 Cylinder cover (directs cold air over the cylinder).

3 Air intake through the crankcase (inside the tank).

Clean the cooling system with a brush once a week, more

often in demanding conditions. A dirty or blocked cooling

system results in the machine overheating which causes

damage to the piston and cylinder.

Spark plug

The spark plug condition is inﬂuenced by:

• Incorrect carburettor adjustment.

• An incorrect fuel mixture (too much or incorrect type

of oil).

• A dirty air ﬁlter.

These factors cause deposits on the spark plug

electrodes, which may result in operating problems and

starting difﬁculties.

If the machine is low on power, difﬁcult to start or runs

poorly at idle speed: always check the spark plug ﬁrst

before taking any further action. If the spark plug is dirty,

clean it and check that the electrode gap is 0,5 mm. The

!

WARNING! If the idle speed cannot be

adjusted so that the cutting attachment

stops, contact your dealer/service

workshop. Do not use the machine until

it has been correctly adjusted or

repaired.

!

WARNING! Mufﬂers ﬁtted with catalytic

converters get very hot during use and

remain so for some time after stopping.

This also applies at idle speed. Contact

can result in burns to the skin.

Remember the risk of ﬁre!

H1153993-26,122HD45,60#4ACBF.fm Page 16 Tuesday, January 4, 2011 8:31 AM

MAINTENANCE

English – 17

spark plug should be replaced after about a month in

operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type!

Use of the wrong spark plug can damage the piston/cylinder.

Check that the spark plug is ﬁtted with a suppressor.

Air ﬁlter

The air ﬁlter must be regularly cleaned to remove dust

and dirt in order to avoid:

• Carburettor malfunctions

• Starting problems

• Loss of engine power

• Unnecessary wear to engine parts.

• Excessive fuel consumption.

Clean the ﬁlter every 25 hours, or more regularly if

conditions are exceptionally dusty.

Cleaning the air ﬁlter

Remove the air ﬁlter cover and take out the ﬁlter. Wash it

clean in warm, soapy water. Allow the ﬁlter to dry and then

oil it in according to the instructions.

An air ﬁlter that has been in use for a long time cannot be

cleaned completely. The ﬁlter must therefore be replaced

with a new one at regular intervals. A damaged air ﬁlter

must always be replaced.

Oiling the air ﬁlter

Always use HUSQVARNA ﬁlter oil, art. no. 531 00 92-48.

The ﬁlter oil contains a solvent to make it spread evenly

through the ﬁlter. You should therefore avoid skin contact.

Put the ﬁlter in a plastic bag and pour the ﬁlter oil over it.

Knead the plastic bag to distribute the oil. Squeeze the

excess oil out of the ﬁlter inside the plastic bag and pour

off the excess before ﬁtting the ﬁlter to the machine. Never

use common engine oil. This would drain through the ﬁlter

quite quickly and collect in the bottom.

Gear

There is a plug for ﬁlling lubricant on the gear housing.

Use the grease tube to ﬁll with grease and repeat every

25 hours. Use Husqvarna’s special grease.

CAUTION! The gear housing must not be ﬁlled

completely with grease. The grease expands as the

machine heats up during operation. If the gear housing

was completely ﬁlled with grease it could damage the

seals and lead to leakage of grease.

The grease in the bevel gear does not normally need to

be changed except if repairs are carried out.

Cutting unit

Check that the cutting units' screws are ﬁtted correctly.

Tighten them with a tightening torque of 7-10 Nm.

Cleaning and lubrication

Clean any resin and plant residue from the blades using

cleaning agent 531 00 75-13 (UL22) before and after

using the machine.

Check that the blade edges are not damaged or

deformed. File away any burrs.

Check that the blades move freely. Remove the

lubrication plug in the gear housing and stick in the

combination spanner and turn back and forth.

Lubricate the blade bars with special grease, part no. 531

00 75-12 (UL 21) before long periods of storage.

H1153993-26,122HD45,60#4ACBF.fm Page 17 Tuesday, January 4, 2011 8:31 AM

18 – English

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the

Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s

Manual. More extensive work must be carried out by an authorized service workshop.

Maintenance Before use:

After 40

hours in use

After 100

hours in use

Clean the outside of the machine. After each time the machine is used

Make sure the throttle trigger lock and the throttle function correctly

from a safety point of view.

X

In order to reduce the risk of ﬁre, dirt, leaves and surplus lubricant, etc

must be cleaned from the mufﬂer, exhaust pipe and engine.

X

Check that the stop switch works correctly. X

Check that the blades do not move when the engine is idling. X

Check that the blades are undamaged and show no signs of cracking

or other damage. Replace the blades if necessary.

X

Check that the blade guard is not damaged or distorted. Replace the

blade if the blade guard is bent or damaged.

X

Replace the cutting unit if it is bent or damaged. X

Check that the hand guard is not damaged. Replace the guard if

damaged.

X

Check that nuts and screws are tight. X

Check that there are no fuel leaks from the engine, tank or fuel lines. X

Clean the air ﬁlter and oil it in.

Clean more often if conditions are exceptionally dusty.

(25 tim).

Check the starter and starter cord. X

Check that the vibration damping elements are not damaged. X

Clean the outside of the spark plug. Remove it and check the electrode

gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that

the spark plug is ﬁtted with a suppressor.

X

Clean the machine’s cooling system. X

Clean the outside of the carburettor and the space around it. X

Fill the gear housing with grease. This should be carried out

approximately every 25 working hours.

X

Check that the screws that hold the blades together are correctly

tightened.

X

Check and clean the spark arrestor mesh on the mufﬂer (only applies

to mufﬂers ﬁtted with a catalytic converter).

X

Clean the inside of the fuel tank. X

Check the inside of the fuel ﬁlter for any dirt or if the fuel hose has any

cracks or other defects. Replace if necessary.

X

Check all cables and connections. X

Check the clutch, clutch springs and the clutch drum for wear. Replace

if necessary by an autorized service workshop.

X

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

X

H1153993-26,122HD45,60#4ACBF.fm Page 18 Tuesday, January 4, 2011 8:31 AM

English – 19

TECHNICAL DATA

Technical data

Note 1: Noise emissions in the environment measured as sound power (L

WA

) in conformity with EC directive 2000/14/

EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the

highest level. The difference between guaranteed and measured sound power is that the guaranteed sound power also

includes dispersion in the measurement result and the variations between different machines of the same model

according to Directive 2000/14/EC.

Note 2: Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard

deviation) of 1 dB (A).

Note 3: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s

2

.

Technical data 122HD45 122HD60

Engine

Cylinder displacement, cm

3

21,7 21,7

Cylinder bore, mm 32 32

Stroke, mm 27 27

Idle speed, rpm 2900 2900

Recommended max. speed, rpm 9000 9000

Max. engine output, acc. to ISO 8893, kW/ rpm 0,6/7800 0,6/7800

Catalytic converter mufﬂer Yes Yes

Speed-regulated ignition system Yes Yes

Ignition system

Spark plug NGK CMR6A NGK CMR6A

Electrode gap, mm 0,5 0,5

Fuel and lubrication system

Fuel tank capacity, litre 0,3 0,3

Weight

Weight without fuel, kg 4,7 4,9

Noise emissions

(see note 1)

Sound power level, measured dB(A) 100 100

Sound power level, guaranteed L

WA

dB(A) 101 101

Sound levels

(see note 2)

Equivalent sound pressure level at the operator’s ear, measured

according to EN ISO 10517, dB(A):

93 94

Vibration levels

(see note 3)

Equivalent vibration levels (a

hv,eq

) at handles, measured according to

EN ISO 10517, m/s

2

Front/rear handles: 2,9/4,9 4,1/3,6

Blades

Type Double sided Double sided

Length, mm 450 590

Blade speed, cuts/min 4050 4050

H1153993-26,122HD45,60#4ACBF.fm Page 19 Tuesday, January 4, 2011 8:31 AM

20 – English

TECHNICAL DATA

EC-declaration of conformity (Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge

trimmers Husqvarna 122HD45 and 122HD60 from 2011’s serial numbers and onwards (the year is clearly stated in

plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative

documents following the provisions in the COUNCIL’S DIRECTIVES:

- of May 17, 2006 "relating to machinery" 2006/42/EC

- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according

to Annex V.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100-2:2009, CISPR 12:2007, EN ISO 10517:2009

SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type

examination on behalf of Husqvarna AB. The certiﬁcates are numbered: SEC/10/2280 - 122HD45, SEC/10/2280 -

122HD60

Huskvarna December 1, 2010

Bo Jonsson, Development manager

(Authorized representative for Husqvarna AB and responsible for technical documentation.)

H1153993-26,122HD45,60#4ACBF.fm Page 20 Tuesday, January 4, 2011 8:31 AM

Sayfa yükleniyor ...

Husqvarna 122HD60 El kitabı

Husqvarna 122HD60 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler