Husqvarna 253 RB El kitabı

Tip
El kitabı
H1153433-10,253RB,GB.fm Page 1 Friday, February 26, 2010 9:55 AM
KEY
T
O SYMBOLS
2
English
Symbols
W
ARNING! A clearing saw,
brushcutter or trimmer can be
dangerous if used incorrectly or
carelessly, and can cause serious or
fatal injury to the operator or others.
It is extremely important that you
read and understand the contents of
this operator’s manual.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
A protective helmet where there
is a risk of falling objects
Approved hearing protection
Approved eye protection
Max. speed of output shaft, rpm
This product is in accordance with
applicable EC directives.
Watch out for thrown objects and
ricochets.
The operator of the machine must
ensure, while working, that no
persons or animals come closer than
15 metres.
Machines fitted with saw blades or
grass blades can be thrown violently
to the side when the blade comes
into contact with a fixed object. This is
called blade thrust. The blade is
capable of amputating an arm or leg.
Always keep people and animals at least 15 metres from
the machine.
Arrows which show limits for handle
positioning.
Always wear approved protective
gloves.
Wear sturdy, non-slip boots.
Only use non-metallic, flexible
cutting attachments, i.e. trimmer
heads with trimmer cord.
Noise emission to the environment
according to the European
Community’s Directive. The
machine’s emission is specified in
chapter Technical data and on label.
Keep all parts of your body away from
hot surfaces.
Other symbols/decals on the mac
hine refer to
special certification requirements for certain
markets.
Switch off the engine by moving the
stop switch to the STOP position
before carrying out any checks or
maintenance.
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
50FT
15 m
50FT
1
5
m
H1153433-10,253RB,GB.fm Page 2 Friday, February 26, 2010 9:55 AM
CONTENTS
English
3
Contents
Note the f
ollowing before
starting:
Please read the oper
ator’s manual carefully.
KEY
TO SYMBOLS
Symbols
................................................................ 2
CONTENTS
Contents
............................................................... 3
Note the following before starting: ........................ 3
INTR
ODUCTION
Dear Customer
, .................................................... 4
WHA
T IS WHAT?
What is what on the br
ush cutter? ........................ 5
GENERAL SAFETY PRECA
UTIONS
Impor
tant .............................................................. 6
Personal protective equipment ............................. 6
Machine
s safety equipment ................................. 7
Cutting equipment ................................................ 10
ASSEMBL
Y
Fitting the fl
exible drive shaft ................................ 12
Connecting throttle cable and stop switch wires ... 12
Fitting the J-handle .............................................. 13
Fitting blades and trimmer heads ......................... 13
Fitting the transport guard .................................... 15
Adjusting the harness and brush cutter ................ 15
FUEL HANDLING
Fuel saf
ety ............................................................ 17
Fuel ...................................................................... 17
Fuelling ................................................................. 18
ST
ARTING AND STOPPING
Chec
k before starting ........................................... 19
Starting and stopping ........................................... 19
W
ORKING TECHNIQUES
Gener
al working instructions ................................ 21
MAINTENANCE
Carb
urettor ........................................................... 24
Air filter ................................................................. 24
Fuel filter ............................................................... 24
Bevel gear ............................................................ 25
Spark plug ............................................................ 25
Drive shaft ............................................................ 25
Maintenance schedule ......................................... 27
TECHNICAL D
ATA
T
echnical data ...................................................... 28
EC-declaration of conformity ................................ 29
!
W
ARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
!
W
ARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
!
W
ARNING! A clearing saw, brushcutter
or trimmer can be dangerous if used
incorrectly or carelessly, and can cause
serious or fatal injury to the operator or
others. It is extremely important that you
read and understand the contents of this
operator’s manual.
H1153433-10,253RB,GB.fm Page 3 Friday, February 26, 2010 9:55 AM
4
English
INTR
ODUCTION
Dear Customer
,
Cong
ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot of different products,
from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor
driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. The business concept is to develop, manufacture and market motor driven products for forestry and
gardening as well as for building and construction industry. Husqvarna
s aim is also to be in the front edge according to
ergonomics, usability, security and environmental protection. That is the reason why we have developed many different
features to provide our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very
long time to come. The purchase of one of our products gives you access to professional help with repairs and service
whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the
address of your nearest service workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator
s manual as a valuable document. By following its
content (using, service, maintenance etc) the life span and
the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get
the operator
s manual.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
H1153433-10,253RB,GB.fm Page 4 Friday, February 26, 2010 9:55 AM
English
5
WHA
T IS
WHA
T?
What is what on the brush cutter?
11
12
18
26
24
25
28
15
14
16
17
10
7
9
8
6
5
3
2
1
4
19
1
20
21
22
14
13
23
27
1
Blade
2 Grease filler cap, bevel gear
3 Bevel gear
4 Cutting attachment guard
5 Shaft
6 J-handle
7 Throttle control
8 Stop switch
9 Throttle lockout
10 Shaft coupling
11 Starter handle
12 Fuel tank
13 Air filter cover
14 Cylinder cover
15 Spark plug cap and spark plug
16 Air purge
17 Choke control
18 Harness
19 Drive disc
20 Support flange
21 Support cup
22 Locking nut
23 Trimmer head
24 Transport guard
25 Locking pin
26 Socket spanner
27 Screwdriver
28 Operator
s manual
H1153433-10,253RB,GB.fm Page 5 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECA
UTIONS
6
English
Impor
tant Personal protective equipment
HELMET
A protectiv
e helmet where there is a risk of falling objects
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with standard
ANSI Z87.1 in the USA or EN 166 in EU countries.
GLOVES
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
IMPORTANT!
The machine is only designed for trimming grass.
The only accessories you can operate with this engine
unit are the cutting attachments we recommend in the
chapter on Technical data.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions
under the heading ”Personal protective equipment”.
Never use a machine that has been modified in any way
from its original specification.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the heading Maintenance.
All covers, guards and handles must be fitted before
starting. Ensure that the spark plug cap and ignition
lead are undamaged to avoid the risk of electric shock.
The machine operator must ensure that no people or
animals come closer than 15 metres while working.
When several operators are working in the same area
the safety distance should be at least twice the tree
height and no less than 15 metres.
!
W
ARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants. To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
!
W
ARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
IMPOR
TANT!
A clearing saw, brushcutter or trimmer can be
dangerous if used incorrectly or carelessly, and can
cause serious or fatal injury to the operator or others. It
is extremely important that you read and understand the
contents of this operator’s manual.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
!
W
ARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
H1153433-10,253RB,GB.fm Page 6 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECA
UTIONS
English
7
BOO
TS
Wear boots with steel toe-caps and non-slip sole.
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants. Do not wear jewellery, shorts
sandals or go barefoot. Secure hair so it is above shoulder
level.
FIRST AID KIT
Always have a first aid kit nearby.
Mac
hine
s safety equipment
This section descr
ibes the machine
s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?” section to locate where this equipment is
positioned on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest service workshop.
Thr
ottle lockout
The throttle loc
kout is designed to prevent accidental
operation of the throttle control. When you press the lock
(A) (i.e. when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle
control and the throttle lockout both move back to their
original positions. This movement is controlled by two
independent return springs. This arrangement means that
the throttle control is automatically locked at the idle
setting.
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Check that the throttle control and throttle lockout move
freely and that the return springs work properly.
See instructions under the heading Start. Start the
machine and apply full throttle. Release the throttle and
check that the cutting attachment stops and remains at a
standstill. If the cutting attachment rotates with the throttle
in the idle position then the carburettor idle setting must
IMPORTANT! All servicing and repair work on the
machine requires special training. This is especially true
of the machine
s safety equipment. If your machine fails
any of the checks described below you must contact
your service agent. When you buy any of our products
we guarantee the availability of professional repairs and
service. If the retailer who sells your machine is not a
servicing dealer, ask him for the address of your nearest
service agent.
!
W
ARNING! Never use a machine with
faulty safety equipment. The machine’s
safety equipment must be checked and
maintained as described in this section.
If your machine fails any of these checks
contact your service agent to get it
repaired.
H1153433-10,253RB,GB.fm Page 7 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECA
UTIONS
8
English
be chec
ked. See instructions under the heading
Maintenance.
Stop s
witch
Use the stop s
witch to switch off the engine.
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting.
Cutting attac
hment guard
This guard is intended to pre
vent loose objects from being
thrown towards the operator. The guard also protects the
operator from accidental contact with the cutting
attachment.
Check that the guard is undamaged and not cracked.
Replace the guard if it has been exposed to impact or is
cracked.
Always use the recommended guard for the cutting
attachment you are using. See chapter on Technical data.
Vibration damping system
Y
our machine is equipped with a vibration damping
system that is designed to minimize vibration and make
operation easier.
Using incorrectly wound cord or a blunt or incorrect
cutting attachment (wrong type or incorrectly filed, see
instructions under the heading Filing the blade) increases
the level of vibration.
The machine
s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine
s handle unit.
Regularly check the vibration damping units for cracks or
deformation. Check that the vibration damping element is
undamaged and securely attached.
Muffl
er
The m
uffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
!
W
ARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
!
W
ARNING! Overexposure to vibration
can lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition. These
symptoms normally appear in the
fingers, hands or wrists. The risk
increases at low temperatures.
H1153433-10,253RB,GB.fm Page 8 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECA
UTIONS
English
9
Ne
ver use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
If the muffler on your machine is fitted with a spark
arrestor mesh this must be cleaned regularly. A blocked
mesh will cause the engine to overheat and may lead to
serious damage.
Loc
king nut
A loc
king nut is used to secure some types of cutting
attachment.
When fitting, tighten the nut in the opposite direction to the
direction of rotation of the cutting attachment. To remove
it, undo the nut in the same direction as the cutting
attachment rotates. (CAUTION! The nut has a left-hand
thread.) Tighten the nut using the socket spanner.
The nylon lining inside the locking nut must not be so worn
that you can turn it by hand. The lining should offer a
resistance of at least 1.5 Nm. The nut should be replaced
after it has been put on approx. 10 times.
Harness
Chec
k that the harness is not damaged.
In an emergency situation, release yourself from machine
and harness according to the following method.
!
W
ARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!
!
W
ARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
W
ARNING! Bear in mind that: The
exhaust fumes from the engine are hot
and may contain sparks which can start
a fire. Never start the machine indoors or
near combustible material!
H1153433-10,253RB,GB.fm Page 9 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECAUTIONS
10 – English
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
Reduce the risk of blade thrust.
Obtain maximum cutting performance.
Extend the life of cutting equipment.
Cutting equipment
Grass blades and grass cutters are intended for cutting
coarse grass.
A trimmer head is intended for trimming grass.
General rules
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Keep the teeth of the blade correctly sharpened! Follow
our instructions and use the recommended file gauge. An
incorrectly sharpened or damaged blade increases the
risk of accidents.
Check the cutting attachment for damage or cracks. A
damaged cutting attachment should always be replaced.
Sharpening grass cutters and grass
blades
See the cutting attachment packaging for correct
sharpening instructions. Sharpen blades and cutters
using a single-cut flat file.
Sharpen all edges equally to maintain the balance of
the blade.
IMPORTANT!
Only use cutting attachments with the guards we
recommend! See the chapter on Technical data.
Refer to the instructions for the cutting attachment to
check the correct way to load the cord and the correct
cord diameter.
Keep the teeth of the blade correctly sharpened! Follow
our recommendations. Also refer to the instructions on
the blade packaging.
!
WARNING! Always stop the engine
before doing any work on the cutting
attachment. This continues to rotate even
after the throttle has been released.
Ensure that the cutting attachment has
stopped completely and disconnect the
HT lead from the spark plug before you
start to work on it.
!
WARNING! Using an incorrect cutting
attachment or an incorrectly sharpened
blade increases the risk of blade thrust.
!
WARNING! Always discard a blade that is
bent, twisted, cracked, broken or
damaged in any other way. Never attempt
to straighten a twisted blade so that it
can be reused. Only use original blades
of the specified type.
H1153433-10,253RB,GB.fm Page 10 Friday, February 26, 2010 9:55 AM
GENERAL SAFETY PRECAUTIONS
English 11
Trimmer head
Only use the recommended trimmer heads and
trimmer cords. These have been tested by the
manufacturer to suit a particular engine size. This is
especially important when a fully automatic trimmer
head is used. Only use the recommended cutting
attachment. See the chapter on Technical data.
Smaller machines generally require small trimmer
heads and vice versa. This is because when clearing
using a cord the engine must throw out the cord
radially from the trimmer head and overcome the
resistance of the grass being cleared.
The length of the cord is also important. A longer cord
requires greater engine power than a shorter cord of
the same diameter.
Make sure that the cutter on the trimmer guard is
intact. This is used to cut the cord to the correct length.
To increase the life of the cord it can be soaked in
water for a couple of days. This will make the line
tougher so that it lasts longer.
IMPORTANT!
Always ensure the trimmer cord is wound tightly and
evenly around the drum, otherwise the machine will
generate harmful vibration.
H1153433-10,253RB,GB.fm Page 11 Friday, February 26, 2010 9:55 AM
ASSEMBLY
12 – English
Fitting the flexible drive shaft
Loosen two screws at the shaft coupling.
Slide the flexible shaft through the loops at the
cabling, and fit the flexible shaft to the shaft coupling.
Make sure the shaft engages correctly by turning it
and pushing at the same time.
Tighten the two screws.
Install the drive shaft sleeve in the clutch cover so that
the hole is positioned directly underneath the locking
button on the clutch cover.
Make sure the shaft engages correctly by turning it
and pushing at the same time.
Make sure the locking pin returns to its original
position, so that the drive shaft sleeve cannot come off
the clutch case.
Connecting throttle cable and
stop switch wires
Place the throttle wire from the cabling (A) and the
throttle wire from the engine (B) in the plastic sleeve
as shown.
Close the plastic sleeve.
Plug the stop switch wires into the matching
connectors from the engine. Note that wire polarity is
not important.
H1153433-10,253RB,GB.fm Page 12 Friday, February 26, 2010 9:55 AM
ASSEMBLY
English 13
Fitting the J-handle
Position the handle on the shaft. Note that the handle
must be mounted below the arrow on the shaft.
Slide the spacer into the slot in the loop handle.
Fit the nut and screw. Do not overtighten.
Attach the J-handle to the loop handle using the three
screws, as shown.
Now adjust the trimmer to give a comfortable working
position. Tighten the bolt/knob.
Fitting blades and trimmer heads
Fitting the guard extension
CAUTION! The guard extension shall always be fitted
when using the trimmer head/plastic blades and
combination guard. The guard extension shall always be
removed when using the grass blade and combination
guard.
Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt.
Enter the guard extension guide in the slot of the
combination guard. Then click the guard extension into
position on the guard with the four quick-fasteners.
!
WARNING! Only grass blades/grass
cutters or trimmer heads/plastic blades
may be used when the J-handle is fitted.
Saw blades must never be used with the
J-handle.
!
WARNING!
When fitting the cutting attachment it is
extremely important that the raised
section on the drive disc/support flange
engages correctly in the centre hole of
the cutting attachment. If the cutting
attachment is fitted incorrectly it can
result in serious and/or fatal personal
injury.
!
WARNING! Never use a cutting
attachment without an approved guard.
See the chapter on Technical data. If an
incorrect or faulty guard is fitted this can
cause serious personal injury.
IMPORTANT! If a saw blade or grass blade are to be
used the machine must be equipped with the correct
handlebar, blade guard and harness.
H1153433-10,253RB,GB.fm Page 13 Friday, February 26, 2010 9:55 AM
ASSEMBLY
14 – English
The guard extension is removed easily using a
screwdriver, see illustration.
Fitting a blade guard, grass blade and
grass cutter
Hook the blade guard/combination guard (A) onto the
fitting on the shaft and secure with the bolt (L). Use the
recommended blade guard. See the Technical data
section. CAUTION! Ensure that the guard extension is
removed.
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
Insert the locking pin (C) in the hole to lock the shaft.
Place the blade (D), support cup (E) and support
flange (F) on the output shaft.
Fit the nut (G). The nut must be tightened to a torque
of 35-50 Nm (3.5-5 kpm). Use the socket spanner in
the tool kit. Hold the shaft of the spanner as close to
the blade guard as possible. To tighten the nut, turn
the spanner in the opposite direction to the direction
of rotation (Caution! left-hand thread).
Fitting the trimmer guard and trimmer
head
Fit the correct trimmer guard (A) for use with the
trimmer head. CAUTION! Ensure that the guard
extension is fitted.
Hook the trimmer guard/combination guard onto the
fitting on the shaft and secure with the bolt (L).
Fit the drive disc (B) on the output shaft.
Turn the blade shaft until one of the holes in the drive
disc aligns with the corresponding hole in the gear
housing.
Insert the locking pin (C) in the hole to lock the shaft.
Screw on the trimmer head/plastic blades (H) in the
opposite direction to the direction of rotation.
To dismantle, follow the instructions in the reverse
order.
A
L
G
E
D
F
B
C
B
A
M
L
H
A
L
C
M
H
H
H1153433-10,253RB,GB.fm Page 14 Friday, February 26, 2010 9:55 AM
ASSEMBLY
English 15
Fitting the transport guard
Insert the blade in the transport guard (A).
Snap the two fasteners (B) into the slots (C) to secure
the transport guard.
Adjusting the harness and brush
cutter
Adjusting the backplate height
Loosen the two fasteners holding the backplate.
Loosen the backplate from the frame on one side.
Move the backplate to the desired height and fasten it.
Make sure the pin aligns with one of the holes on the
frame, see picture.
Adjusting the harness
Put on the harness.
Tighten the waist strap so that it sits securely.
H1153433-10,253RB,GB.fm Page 15 Friday, February 26, 2010 9:55 AM
ASSEMBLY
16 – English
Tighten the chest strap.
Adjust the chest strap vertically if needed and make
sure it fits well.
Adjust the shoulder straps to distribute the load evenly
across your shoulders.
Loosen or tighten the waist strap so that approx. 70%
of the load is on your waist and 30% on your
shoulders.
H1153433-10,253RB,GB.fm Page 16 Friday, February 26, 2010 9:55 AM
FUEL HANDLING
English 17
Fuel safety
Never start the machine:
1 If you have spilt fuel on it. Wipe off the spillage and
allow remaining fuel to evaporate.
2 If you have spilt fuel on yourself or your clothes,
change your clothes. Wash any part of your body that
has come in contact with fuel. Use soap and water.
3 If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.
Transport and storage
Store and transport the machine and fuel so that there
is no risk of any leakage or fumes coming into contact
with sparks or naked flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
When storing and transporting fuel always use
approved containers intended for this purpose.
When storing the machine for long periods the fuel
tank must be emptied. Contact your local petrol
station to find out where to dispose of excess fuel.
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
Secure the machine during transport.
Fuel
CAUTION! The machine is equipped with a two-stroke
engine and must always been run using a mixture of
petrol and two-stroke oil. It is important to accurately
measure the amount of oil to be mixed to ensure that the
correct mixture is obtained. When mixing small amounts
of fuel, even small inaccuracies can drastically affect the
ratio of the mixture.
Petrol
CAUTION! Always use a quality petrol/oil mixture at least
90 octane (RON). If your machine is equipped with a
catalytic converter (see chapter on Technical data) always
use a good quality unleaded petrol/oil mixture. Leaded
petrol will destroy the catalytic converter.
Use low-emission petrol, also known as alkylate petrol, if
it is available.
The lowest octane recommended is 90 (RON). If you
run the engine on a lower octane grade than 90 so-
called knocking can occur. This gives rise to a high
engine temperature, which can result in serious
engine damage.
When working at continuous high revs a higher octane
rating is recommended.
Two-stroke oil
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two-stroke engines.
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
Never use oil intended for four-stroke engines.
A poor oil quality and/or too high oil/fuel ratio may
jeopardise function and decrease the life time of
catalytic converters.
Mixing ratio
1:50 (2%) with HUSQVARNA two-stroke oil.
1:33 (3%) with oils class JASO FB or ISO EGB
formulated for air-cooled, two-stroke engines.
!
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion
and inhaling fumes.
!
WARNING! Fuel and fuel fumes are
highly inflammable and can cause
serious injury when inhaled or allowed to
come in contact with the skin. For this
reason observe caution when handling
fuel and make sure there is adequate
ventilation.
Petrol, litre
Two-stroke oil, litre
2% (1:50) 3% (1:33)
5 0,10 0,15
10 0,20 0,30
15 0,30 0,45
20 0,40 0,60
H1153433-10,253RB,GB.fm Page 17 Friday, February 26, 2010 9:55 AM
FUEL HANDLING
18 – English
Mixing
Always mix the petrol and oil in a clean container
intended for fuel.
Always start by filling half the amount of the petrol to
be used. Then add the entire amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount of
petrol.
Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
Do not mix more than one month’s supply of fuel at a
time.
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Fuelling
Always use a fuel container with an anti-spill valve.
Clean the area around the fuel cap. Contamination in
the tank can cause operating problems.
Ensure that the fuel is well mixed by shaking the
container before filling the tank.
!
WARNING! The catalytic converter
muffler gets very hot during and after
use. This also applies during idling. Be
aware of the fire hazard, especially when
working near flammable substances and/
or vapours.
!
WARNING! Taking the following
precautions, will lessen the risk of fire:
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refuelling.
Always stop the engine and let it cool for
a few minutes before refuelling.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refuelling.
Always move the machine away from the
refuelling area before starting.
H1153433-10,253RB,GB.fm Page 18 Friday, February 26, 2010 9:55 AM
STARTING AND STOPPING
English 19
Check before starting
Never use the machine without a guard nor with a
defective guard.
All covers must be correctly fitted and undamaged
before you start the machine.
Check the blade to ensure that no cracks have formed
at the bottom of the teeth or by the centre hole. The
most common reason why cracks are formed is that
sharp corners have been formed at the bottom of the
teeth while sharpening or that the blade has been
used with dull teeth. Discard a blade if cracks are
found.
Check that the support flange is not cracked due to
fatigue or due to being tightened too much. Discard
the support flange if it is cracked.
Ensure the locking nut has not lost its captive force.
The nut lock should have a locking force of at least 1.5
Nm. The tightening torque of the locking nut should be
35-50 Nm.
Check that the blade guard is not damaged or
cracked. Replace the blade guard if it is exposed to
impact or is cracked.
Check that the trimmer head and trimmer guard are
not damaged or cracked. Replace the trimmer head or
trimmer guard if they have been exposed to impact or
are cracked.
Starting and stopping
Starting
Ignition: Set the stop switch to the start position.
Primer bulb: Press the air purge repeatedly until fuel
begins to fill the bulb. The bulb need not be completely
filled.
!
WARNING! The complete clutch cover
and shaft must be fitted before the
machine is started, otherwise the clutch
can come loose and cause personal
injury.
Always move the machine away from the
refuelling area before starting. Place the
machine on a flat surface. Ensure the
cutting attachment cannot come into
contact with any object.
Make sure no unauthorised persons are
in the working area, otherwise there is a
risk of serious personal injury. The safety
distance is 15 metres.
H1153433-10,253RB,GB.fm Page 19 Friday, February 26, 2010 9:55 AM
STARTING AND STOPPING
20 – English
Choke: Set the choke control in the choke position.
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord.
Never twist the
starter cord around your hand.
Repeat pulling the cord until the engine starts. When the
engine starts. return choke control to run position and
apply full throttle; the throttle will automatically disengage
from the start setting.
CAUTION! Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
CAUTION! Do not put any part of your body in marked
area. Contact can result in burns to the skin, or electrical
shock if the spark plug cap has been damaged. Always
use gloves. Do not use a machine with damaged spark
plug cap.
Stopping
Stop the engine by switching off the ignition.
!
WARNING! When the engine is started
with the choke in either the choke or
start throttle positions the cutting
attachment will start to rotate
immediately.
H1153433-10,253RB,GB.fm Page 20 Friday, February 26, 2010 9:55 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200

Husqvarna 253 RB El kitabı

Tip
El kitabı