Yamaha BD-S667 El kitabı

Printed in China BD-S667_G

BD-S667

USB

BLU-RAY DISC PLAYER

LECTEUR BLU-RAY DISC

BD-S667

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

00_BD-S667_G_cv.fm Page 1 Friday, April 2, 2010 5:39 PM

Caution-i En

Important notes for users in the

U.K.

Mains plug

This apparatus is fitted with an approved 13 Amp

plug. To change a fuse in this type of plug proceed

as follows:

1 Remove fuse cover and fuse.

2 Fix new fuse which should be a BS1362 5 Amp,

A.S.T.

3 Refit the fuse cover.

If the fitted plug is not suitable for your jack outlets,

it should be cut off and an appropriate plug fitted in

its place.

If the mains plug contains a fuse, this should have a

value of 5 Amp. If a plug without a fuse is used, the

fuse at the distribution board should not be greater

than 5 Amp.

Note: The severed plug must be disposed to avoid a

possible shock hazard should it be inserted into a 13

Amp jack elsewhere.

How to connect a plug

The wires in the mains lead are coloured with the

following code:

blue = neutral (N), brown = live (L).

• As these colours may not correspond with the

colour markings identifying the terminals in your

plug, proceed as follows:

– Connect the blue wire to the terminal marked N

or coloured black

– Connect the brown wire to the terminal marked

L or coloured red.

– Do not connect either wire to the earth terminal

in the plug, marked E (or e) or coloured green (or

green and yellow).

Before replacing the plug cover, make certain that

the cord grip is clamped over the sheath of the lead -

not simply over the two wires.

Copyright in the U.K.

Recording and playback of material may require

consent. See Copyright Act 1956 and The

Performer’s Protection Acts 1958 to 1972.

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai

asetusten muutto saattaa altistaa vaaralliselle säteilylle tai

muille vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse

for stråling.

Bemærk: Netafbryderen p er sekundært indkoblet og

ofbryder ikke strømmen fra nettet. Den indbyggede netdel

er derfor tilsluttet til lysnettet så længe netstikket sidder i

stikkontakten.

N

Observer: Nettbryteren p er sekundert innkoplet. Den

innebygdenetdelen er derfor ikke frakoplet nettet så lenge

apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för

osynlig laserstrålning, som överskrider gränsen för

laserklass 1.

Observera! Strömbrytaren p är sekundärt kopplad och

inte bryter inte strömmen från nätet. Den inbyggda

nätdelen är därför ansluten till elnätet så länge

stickproppen sitter i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä

käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän

turvallisuusluokan 1 ylittävälle näkymättömälle

lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina

tippu-ja roiskevedelle.

Toiminnanvalitsin p on kytketty toisiopuolelle, eikä se

kytke laitetta irti sähköverkosta. Sisäänrakennettu verkko-

osa on kytkettynä sähköverkkoon aina silloin, kun pistoke

on pistorasiassa.

VARO!

AVATTAESSA JA SUOJALUKITUS

OHITETTAESSA OLET ALTTIINA

NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

Caution-ii En

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou

de méthodes autres que ceux décrits ci-dessous,

peuvent entraîner une exposition à un rayonnement

dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die

Einstellung bzw. die Ausführung von anderen als in

dieser Anleitung beschriebenen Vorgängen kann zu

Gefährdung durch gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande

av åtgärder på annat sätt än så som beskrivs häri kan

resultera i farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure

non specificati in questo manuale possono risultare in

esposizione a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos

que no se especifican enste manual pueden causar una

exposición peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of

procedures anders dan beschreven in dit document kan

leiden tot blootstelling aan gevaarlijke stralen.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

CAUTION:

LASER RADIATION WHEN OPEN.

DO NOT STARE INTO BEAM.

LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO THE BEAM.

DANGER:

Caution-iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top: 10 cm (4 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and

may cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a lightning

storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit is

faulty.

17 Before moving this unit, press p to set this unit to the

standby mode, and disconnect the AC power plug from the

wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power cable from the

outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn the power off, then leave this unit alone for

cooling.

20 Install this unit near the AC outlet and where the AC power

plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as

sunshine, fire or the like.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt

to service this device.

DANGER

This unit emits visible laser radiation when open. Avoid

direct eye exposure to beam. When this unit is plugged into

the wall outlet, do not place your eyes close to the opening of

the disc tray and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off by p. This state is called the

standby mode. In this state, this unit is designed to

consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

The laser component in this product is capable of

emitting radiation exceeding the limit for Class 1.

LASER Specification:

Class 1 LASER Product

Wave length: 790 nm (CDs)/655 nm (DVDs)/405 nm (BDs)

Laser output: max. 1 mW

1 En

1

2

3

4

5

English

WHAT YOU CAN DO WITH THIS PLAYER........ 2

SUPPLIED PARTS .............................................. 2

ABOUT DISCS AND FILES................................. 3

Types of discs/files that can be used with this player..... 3

Disc precautions ............................................................. 4

Loading a disc................................................................. 4

CONTROLS AND FUNCTIONS .......................... 5

Front panel...................................................................... 5

Remote control ............................................................... 6

INTRODUCTION TO CONNECTIONS ................ 8

Rear panel....................................................................... 8

HDMI CONNECTION......................................... 10

Connecting to the HDMI terminal................................ 10

VIDEO CONNECTIONS .................................... 11

Connecting to the component/video jack ..................... 11

AUDIO CONNECTIONS.................................... 12

Connecting to the digital audio jack/terminal............... 12

Connecting to the audio jacks....................................... 13

NETWORK AND USB CONNECTION .............. 14

Connecting to the NETWORK terminal and USB/BD

STORAGE terminal................................................. 14

OTHER CONNECTIONS................................... 15

Connecting to the REMOTE CONTROL jacks ........... 15

Connecting the power cable ......................................... 15

INITIAL WIZARD/EASY SETUP........................ 16

Setting with the Initial Wizard/Easy Setup................... 16

HOME MENU..................................................... 17

Playing back photo/music/video................................... 17

Using network content.................................................. 19

ADVANCED PLAYBACK OPERATION............ 20

On Screen menu............................................................ 20

Status menu................................................................... 21

Using Bookmark........................................................... 22

Program play................................................................. 22

Using search ................................................................. 22

Enjoying BONUSVIEW and BD-Live......................... 23

Using Picture in Picture function

(secondary audio/video playback) ........................... 23

Using the feature of BD-Live....................................... 23

SETUP MENU.................................................... 24

Example of SETUP menu operation ............................ 25

General Setting ............................................................. 26

Display Setting ............................................................. 28

Audio Setting................................................................ 29

System Information ...................................................... 29

About the audio output formats.................................... 30

About the video output formats.................................... 30

SOFTWARE UPGRADE.................................... 32

Upgrading the software ................................................ 32

TROUBLESHOOTING....................................... 33

Power ............................................................................ 33

Basic operation.............................................................. 33

Disc playback................................................................ 33

Picture ........................................................................... 33

Sound ............................................................................ 34

Network......................................................................... 34

Messages on the screen................................................. 34

GLOSSARY ....................................................... 35

SPECIFICATIONS ............................................. 36

General.......................................................................... 36

Audio performance ....................................................... 36

Input/output................................................................... 36

Copyright ...................................................................... 37

(at the end of this manual)

■ About this manual

– This manual describes how to operate this Player

using a remote control except when it is not

available. Some of these operations are also

available using the front panel buttons.

– Notes contain important information about safety

and operating instructions. Hint(s) indicates a tip for

your operation.

– This manual is printed prior to production. Design

and specifications are subject to change in part as a

result of improvements, etc. In case of differences

between the manual and the product, the product has

priority.

The icons used in this manual

Icons are used to indicate available buttons/functions for a

particular format.

: BD-Video

: DVD-Video, DVD-VR, DVD+VR

: Audio CD

: MP3, WMA

: AVCHD, WMV, DivX

: JPEG

CONTENTS

1. INTRODUCTION

2. CONNECTION

3. PLAYBACK

4. SETTINGS

5. ADDITIONAL INFORMATION

About fonts................................................................i

BD

DVD

CD

MUSIC

VIDEO

PHOTO

2 En

INTRODUCTION

* For details on playable disc and format, see page 3.

** Network setting is needed to use this function.

Make sure the following accessories are provided with the product.

WHAT YOU CAN DO WITH THIS PLAYER

Easy setting for language, resolution, screen aspect ratio \ p. 16

You can perform language and TV settings.

Play back commercially-released BD/DVD/CD discs

*

\ p. 20

In addition to BD discs, this Player also supports playback of a variety of other discs.

Play back BONUSVIEW, BD-Live, etc.

*

\ p. 23

You can enjoy additional movies on the latest BD discs.

Play back Video, Music, Photo files on a disc

*

\ p. 17

This Player can play back discs you recorded.

Play back Video, Music, Photo files on a disc/USB memory device

*

\ p. 17

Files recorded on discs/USB memory devices can be played back with this Player.

Play back Video, Music, Photo files on a Home Network Server

*

**

\ p. 19

PC contents can be played back with TV or AV receiver by connecting this Player to a network

server.

Operation with the remote control of TV, AV receiver, etc. \ p. 26

Connecting devices with an HDMI cable, you can control devices with a single remote control

using the HDMI Control function.

SUPPLIED PARTS

Batteries (×2)

(AAA, R03, UM-4)

Audio/Video cable Power cableRemote control

MARKER

PROGRAM

PIP

2

ND

AUDIO

DIGEST

REPEAT

TOP

MENU

ON

SCREEN

RETURN

SUBTITLE

ANGLE

STATUS

ZOOM AUDIO

POP

-

UP

MENU

A B

HOME

ENTER

TRANSMIT

SETUP

SEARCH

CLEAR

ABCD

3 En

English

INTRODUCTION

1

■ Types of discs/files that can be

used with this player

– 12 cm (5”) and 8 cm (3”) discs can be played back in

this Player. Do not use an 8 cm (3”) to 12 cm (5”)

adapter.

– Use discs that conform to compatible standards as

indicated by the presence of official logos on the

disc label. Playback of discs not complying with

these standards is not guaranteed. In addition, the

image quality or sound quality is not guaranteed

even if the discs can be played back.

– BD/DVD video players and discs have region codes,

which dictate the regions in which a disc can be

played.

– BD/DVD Video operations and functions may be

different from the explanations in this manual and

some operations may be prohibited due to disc

manufacturer’s settings.

– If a menu screen or operating instructions are

displayed during playback of a disc, follow the

operating procedure displayed.

Notes

– Playback for some of the discs in the left side

column tables may not be possible depending on the

disc.

– Finalize all recording media that is played back in

this player.

– “Finalize” refers to a recorder processing a recorded

disc so that it will play in other players/recorders as

well as this Player. Only finalized discs will play

back in this Player. (This Player does not have a

function to finalize discs.)

– Playback of all files on the disc, USB memory

device and network is not guaranteed.

– A copyright protected file cannot be played back via

USB memory device and network.

MP3/WMA audio file requirement

– Sampling frequency: within 32 - 48 kHz

– Bitrate: within 8 - 320 kbps (MP3), 32 - 192 kbps

(WMA)

WMV file requirement

– WMV9, maximum resolution is 1,920 × 1,080.

ABOUT DISCS AND FILES

Disc Type

Recording

Format

Data Format

BD-ROM/BD-R/

BD-RE

BD-Video --

DVD-ROM DVD-Video --

DVD-R/DVD-R DL/

DVD-RW

DVD-Video/DVD-

VR/AVCHD/Data

Disc

DivX/WMV/MP3/

WMA/JPEG

DVD+R/DVD+R

DL/DVD+RW

DVD-Video/

DVD+VR/AVCHD/

Data Disc

DivX/WMV/MP3/

WMA/JPEG

CD-ROM CDDA/HDCD --

CD-R/CD-RW CDDA/Data Disc DivX/WMV/MP3/

WMA/JPEG

USB -- DivX/WMV/MP3/

WMA/JPEG

Network -- WMV/MP3/WMA/

JPEG

Region management information

Destination BD-Video DVD-Video

U.S.A. and Canada Region code “A” or

“ALL”

Region number “1”

or “ALL”

Asia Region code “A” or

“ALL”

Region number “3”

or “ALL”

Central and South

America

Region code “A” or

“ALL”

Region number “4”

or “ALL”

Europe Region code “B” or

“ALL”

Region number “2”

or “ALL”

1

ALL

3

ALL

4

ALL

2

ALL

Australia Region code “B” or

“ALL”

Region number “4”

or “ALL”

Russia Region code “C” or

“ALL”

Region number “5”

or “ALL”

China Region code “C” or

“ALL”

Region number “6”

or “ALL”

Region management information

Destination BD-Video DVD-Video

4

ALL

5

ALL

4 En

ABOUT DISCS AND FILES

■ Disc precautions

Be careful of scratches and dust

– BD, DVD and CD discs are sensitive to dust,

fingerprints and especially scratches. A scratched

disc may not be able to be played back. Handle discs

with care and store them in a safe place.

Proper disc storage

Handling precautions

Cleaning the pick up lens

– Never use commercially available cleaning discs.

The use of these discs can damage the lens.

– Request the nearest service center approved by

Yamaha to clean the lens.

■ Loading a disc

– Insert the disc with the label face up.

– In case of the disc recorded on both sides, face down

the side to play back.

Notes

– Playback may begin automatically, depending on the

disc and setting of this Player.

– The menu may be displayed first, depending on the

disc.

– The disc load time may vary depending on the disc.

Place the disc in the center of the disc case

and store the case and disc upright.

Avoid storing discs in locations subject to

direct sunlight, close to heating appliances

or in locations of high humidity.

Do not drop discs or subject them to

strong vibrations or impacts.

Avoid storing discs in locations where

there are large amounts of dust or

moisture.

– If the surface is soiled, wipe gently with a

soft, damp (water only) cloth. When

wiping discs, always move the cloth from

the center hole toward the outer edge.

– Do not use record cleaning sprays,

benzene, thinner, static electricity

prevention liquids or any other solvent.

– Do not touch the surface.

– Do not stick paper or adhesive labels to the disc.

– If the playing surface of a disc is soiled or scratched,

the Player may decide that the disc is incompatible

and eject the disc tray, or it may fail to play the disc

correctly. Wipe any dirt off the playing surface with

a soft cloth.

5 En

English

INTRODUCTION

1

■ Front panel

1 p (On/Standby)

2 USB port (p. 14)

3 Indicator: Lights up while this Player is starting up.

4 Front panel display

5 Disc tray (p. 4)

6 (Eject) (p. 4)

7 (Search backward/Skip backward):

Press to skip backward, and press and hold to search

backward.

8 (Search forward/Skip forward):

Press to skip forward, and press and hold to search

forward.

9 (Play)

0 (Pause)

A (Stop)

Loading the batteries in the remote

control

Notes

– Do not subject the remote control unit to shock,

water or excessive humidity.

– The remote control unit may not function if the

Player’s remote sensor is in direct sunlight or any

other strong light.

– Incorrect use of batteries may cause them to leak or

burst. Read the battery warnings and use the

batteries properly.

– Do not mix old and new batteries, or mix different

brands.

– Remove the batteries if you will not use the remote

control unit for an extended period of time.

– Dispose of batteries according to your regional

regulations.

Approximate operating range of

remote control

CONTROLS AND FUNCTIONS

USB

2 5 61 43 7 8 9 0 A

1

3

2

MARKER

PROGRAM

PIP

2

ND

AUDIO

DIGEST

REPEAT

TOP

MENU

ON

SCREEN

RETURN

SUBTITLE

ANGLE

STATUS

ZOOM AUDIO

POP

-

UP

MENU

A B

HOME

ENTER

TRANSMIT

SETUP

SEARCH

CLEAR

ABCD

USB

30˚30˚

Remote control sensor

6 m (20 ft)

6 En

CONTROLS AND FUNCTIONS

■ Remote control

Note

– will appear on the top left corner of the screen

when the pressed button is not available.

1 Infrared signal transmitter: Outputs infrared

signal. Aim this window to the remote control sensor

(p. 5).

2 TRANSMIT: Flashes while the remote control is

sending infrared signal.

3 MARKER : Sets Bookmark (p. 22) at

a specified point of a movie. After Bookmark is set,

you can jump to the point you set using this function.

You can set up to 12 Bookmarks.

4 : Opens/closes the disc tray.

5 Color buttons : Use these buttons according to

on-screen instructions.

6 Number buttons: Enters numbers, or during

playback, jumps to the track/chapter corresponding to

the number you input.

7 CLEAR: Clears entered number/set item.

8 PROGRAM : Sets the order of playback

(p. 22). You can set up to 15 tracks (for Audio CD) or

titles/chapters (DVD-Video).

9 PIP : Turns on/off the Picture in Picture (p. 23).

PIP Mark ( ) is displayed on the screen when this

function is available. You can also select this item from

On Screen menu (p. 20).

Note

– PIP Mark is displayed only when the PIP Mark is set

to on (p. 27).

0 2ND AUDIO : Turns on/off the secondary audio

of the Picture in Picture (p. 23) or audio

commentaries. The Secondary Audio Mark ( ) is

displayed on the screen when this function is

available. You can also select this item from On

Screen menu (p. 20).

Note

– Secondary Audio Mark is displayed only when

Secondary Audio Mark is set to on (p. 27).

A HOME: Displays the HOME menu screen (p. 17).

B TOP MENU : Displays the top menu

screen (p. 36) if the disc contains a menu. Select the

desired item using 5/a /2 /3 and ENTER.

Note

– Specific operations may be different depending on

the disc. Follow the instructions of each menu

screen.

C Cursor buttons (5 /a /2/3): Moves the focus in

the menu screen.

ENTER: Selects the focused menu/item.

D RETURN: Returns to the previous menu or screen,

etc.

E ANGLE : Changes the camera angle if

video is recorded with multiple angles. The Angle

Mark ( ) is displayed on the screen when this

function is available. You can also select this item

from On Screen menu (p. 20).

Note

– Angle Mark is displayed only when the Angle Mark

is set to on (p. 27).

F SUBTITLE : Changes subtitle

languages (p. 36) if available . You can also select this

item from On Screen menu (p. 20).

MARKER

PROGRAM

PIP

2

ND

AUDIO

DIGEST

REPEAT

TOP

MENU

ON

SCREEN

RETURN

SUBTITLE

ANGLE

STATUS

ZOOM AUDIO

POP

-

UP

MENU

A B

HOME

ENTER

TRANSMIT

SETUP

SEARCH

CLEAR

ABCD

F

G

B

D

0

C

M

L

K

I

N

7

6

5

P

4

Q

3 R

O

8

9

2

E

A

1

H

J

DVD

VIDEO

BD

CD DVD

BD

BD DVD

BD DVD VIDEO

7 En

CONTROLS AND FUNCTIONS

English

INTRODUCTION

1

G Control buttons

/: Searches backward/forward. The search

speed will change each time you press the button

(search backward/forward: 5 steps each). Press to

resume normal playback.

( )/ ( ) : Performs slow

backward/forward. Slow playback speed will change

each time you press the button (slow backward/

forward: 4 steps each).

These buttons also perform frame advance/reverse

playback during pause.

Press to resume normal playback.

: Stops playback. To stop playback completely,

press this button twice.

: Pauses playback.

: Plays back contents.

/: Skips backward/forward.

Notes

– Some BD/DVD discs are not compatible with frame

advance/reverse playback.

– The Player resumes playback from the point that

where the Player was previously stopped. To play

back from the beginning, press and then .

H STATUS: Displays the playback information (p. 21).

I AUDIO : Changes the audio language or

format. You can also select this item from On Screen

menu (p. 20).

J ZOOM : Zooms in/out.

The size of the screen will change each time you press

the button (zoom in/out: 3 steps each).

K ON SCREEN: Displays On Screen menu (p. 20).

L POP-UP MENU : Displays pop-up

menu. The menu contents displayed vary depending

on the disc. For details on how to see and operate the

pop-up menu, refer to the manual for the disc.

The top menu screen may be displayed by pressing

POP-UP MENU depending on the DVD.

M A/B :

Plays back a specific part you want to repeat.

1 Press A/B at the scene where you want to set the

start point. “A-” is displayed on the screen.

2 Press A/B again at the scene where you want to set

the end point. “A-B” is displayed on the screen.

Repeat playback starts.

3 To cancel the repeat playback, press A/B. “A-B”

disappears and the repeat playback is finished.

Note

– This function cannot be performed depending on the

specifications of the disc.

N REPEAT :

Changes repeat mode. Repeat mode shown below will

change each time you press the button.

: Repeats the title being played back.

: Repeats the chapter being played back.

: Repeats all tracks/files on the disc/folder.

: Repeats the track/file being played back.

O DIGEST : Shows 12 photo thumbnails.

When thumbnails are displayed, you can proceed to

the next/previous page with / .

P SEARCH :

Jumps to a specified point during playback. For details

on this function, refer to “Using search” (p. 22). You

can also select this item from status menu (p. 21).

Q p: Turns this Player on or sets it to the standby mode.

R SETUP: Displays SETUP menu screen (p. 24).

BD DVD CD VIDEO MUSIC PHOTO

BD DVD

DVD VIDEO PHOTO

BD DVD

BD DVD CD VIDEO MUSIC

PHOTO

BD DVD CD VIDEO MUSIC

8 En

CONNECTION

Find the corresponding connection method on your video/audio equipment. We recommend that you use the HDMI

terminal which provides high quality digital audio and video on a single connection. If you use the other terminals/jacks,

connect the video first. Then connect the audio.

■ Rear panel

INTRODUCTION TO CONNECTIONS

Yes

No

Use AV receiver?

HDMI terminal on

AV receiver?

*

HDMI terminal on TV?

Connect video and audio to TV with HDMI cable.

Connect video to TV.

Connect video to TV with HDMI cable.

Connect video to AV receiver.

Connect video and audio to AV

receiver with HDMI cable.

Refer to owner’s manual

of AV receiver.

START

* When you connect to an AV receiver that cannot output the sound

input via its HDMI terminal, refer to the owner’s manual of your AV

receiver.

REMOTE CONTROL

OUT IN

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

670 9

321 4

8

5

9 En

English

CONNECTION

2

1 COAXIAL (p. 12)

2 L/R (AUDIO OUT) (p. 13)

3 COMPONENT (p. 11)

4 HDMI (p. 10)

5 NETWORK (p. 14)

6 AC inlet (p. 15)

7 REMOTE CONTROL (IN/OUT) (p. 15)

8 USB/BD STORAGE (p. 14)

9 VIDEO (p. 11)

0 OPTICAL (p. 12)

Video connection

Connect audio to AV

receiver.

Video connection to TV

Connect audio to TV.

HDMI (p. 10)

A

Video and audio connection to

AV receiver

Audio connection to AV receiver

Video and audio connection to TV

Audio connection to TV

HDMI (p. 10)

A’

COMPONENT (p. 11)

B

VIDEO (p. 11)

C

to TV

to AV receiver

or

COMPONENT (p. 11)

B’

VIDEO (p. 11)

C’

or

COAXIAL (p. 12)

D

OPTICAL (p. 12)

E

or

L/R (p. 13)

F

or

COAXIAL (p. 12)

D’

OPTICAL (p. 12)

E’

or

L/R (p. 13)

F’

or

HDMI (p. 10)

A’

10 En

■ Connecting to the HDMI terminal

– You can enjoy high quality digital picture and sound through the HDMI terminal.

– Firmly connect an HDMI cable (commercially available) to the HDMI terminals.

– See page 30 for information on the audio/video output formats.

– Use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the back cover).

Caution!

Do not connect the power cable of this Player until all connections are completed.

HDMI CONNECTION

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

HDMI IN

This Player

To HDMI terminal

HDMI cable

(commercially available)

Hints

– When you use the HDMI Control function,

refer to the “HDMI Control” (p. 26).

– For information on the output mode of HDMI

terminal, refer to the “HDMI” (p. 29).

AV receiver

TV

A A’

To HDMI input terminal

11 En

English

CONNECTION

2

■ Connecting to the component/video jack

– You can enjoy accurate color reproduction and high quality images through the component jacks.

– Firmly connect a component video cable (commercially available) or an Audio/Video cable to the COMPONENT

jacks/VIDEO jack.

– See page 30 for information on the video output formats.

Caution!

Do not connect the power cable of this Player until all connections are completed.

Note

– If you play back the image via VCR, the image may deteriorate due to the copy guard function.

VIDEO CONNECTIONS

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

COMPONENT IN

Y

PB

PR

This Player

Component video cable

(commercially available)

AV receiver

TV

(Green)

(Blue)

(Red)

(Green)

(Blue)

(Red)

To COMPONENT

jacks

To component

input jacks

B B’

(Green)

(Blue)

(Red)

(Green)

(Blue)

(Red)

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

VIDEO

AV INPUT

This Player

Audio/Video cable

(supplied)

AV receiver TV

(Yellow)

To VIDEO

jack

To video

input jack

(Yellow)

C C’

12 En

■ Connecting to the digital audio jack/terminal

– You can connect audio equipment or the TV to the COAXIAL jack/OPTICAL terminal.

– Firmly connect a Coaxial digital audio cable (commercially available) or optical cable (commercially available) to

the coaxial digital audio jack or optical digital audio terminal.

– See page 30 for information on the audio output formats.

Caution!

Do not connect the power cable of this Player until all connections are completed.

Hint

– For information on the output mode of COAXIAL jack/OPTICAL terminal, refer to the “COAXIAL/OPTICAL”

(p. 29).

AUDIO CONNECTIONS

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

AV INPUT

COAXIAL

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

DIGITAL AUDIO IN

OPTICAL

This Player

To OPTICAL

terminal

TVAV receiver

Optical cable

(commercially available)

Coaxial digital audio cable

(commercially available)

This Player

AV receiver

D D’

To COAXIAL

jack

To coaxial

input jack

To optical

input terminal

TV

D’ E E’

AUDIO CONNECTIONS

13 En

English

CONNECTION

2

■ Connecting to the audio jacks

– You can connect audio equipment or the TV to the AUDIO OUT L/R jacks.

– Firmly connect an Audio/Video cable (supplied) to the AUDIO OUT L/R jack.

– See page 30 for information on the audio output formats.

Caution!

Do not connect the power cable of this Player until all connections are completed.

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

AUDIO

AUDIO IN

LR

To AUDIO OUT

L/R jack

Audio/Video cable

(supplied)

(White)

(Red)

(White) (Red)

TVAV receiver

This Player

To audio L/R

input jack

F F’

(White)

(Red)

(White)

(Red)

14 En

■ Connecting to the NETWORK terminal and USB/BD STORAGE terminal

– PC contents can be played back by connecting this Player to the network.

– You can enjoy a variety of contents with interactive functions by connecting to the internet when playing BD-Live

compatible discs. Refer to page 23 regarding further information on BD-Live functions.

– You can connect a USB memory device (2 GB or greater and formatted with FAT 32/16) to the USB/BD

STORAGE terminal to save the BD-Live data or to upgrade the software of this Player.

– Firmly connect a network cable (commercially available) and a USB memory device (commercially available) to

the NETWORK terminal and USB/BD STORAGE terminal.

– Use only an STP (shielded twisted pair) network cable.

– When using the internet, a broadband internet connection as shown below is required.

– Connect the other connector of the network cable to the hub/broadband router.

– The USB memory device connected to the USB port on the front panel works same as the one connected to the

USB/BD STORAGE terminal on the rear panel.

Before using the USB memory device

After connecting

– When you set the Network setting manually, refer to “Network” (p. 27).

– To play back the PC contents on your network, refer to “Using network content” (p. 19).

NETWORK AND USB CONNECTION

R

L

COAXIAL

COMPONENT

YPB

PR

OPTICAL VIDEO

DIGITAL OUT AUDIO OUT

VIDEO OUT

NETWORK

USB BD STORAGE

HDMI

LAN

This Player

Notes

– When using a broadband internet

connection, a contract with an internet

service provider is required. For more

details, contact your nearest internet service

provider.

– Refer to the operation manual of the

equipment you have as the connected

equipment and connection method may

differ depending on your internet

environment.

– Use a network cable/router supporting

10BASE-T/100BASE-TX.

CAUTION:

– Do not remove the USB memory device

or unplug the power cable while the

operations for BUDA (p. 35) or software

upgrade are being performed.

– Do not use a USB extension cable when

connecting a USB memory device to the

USB/BD STORAGE terminal of the

Player. Using a USB extension cable

may prevent the Player from performing

correctly.

Note

– Yamaha cannot guarantee that all brands’

USB memory devices will operate with

this Player.

To NETWORK

terminal

Internet

Modem

Network cable

(commercially available)

Hub or

broadband router

PC

To USB/BD

STORAGE

Terminal

USB memory device

(commercially available)

To LAN

terminal

15 En

English

CONNECTION

2

■ Connecting to the REMOTE

CONTROL jacks

– You can transmit and receive the remote control

signals by connecting to the REMOTE CONTROL

(OUT/IN) jacks.

– Firmly connect monaural 3.5 mm mini plug cables

(commercially available) to the REMOTE

CONTROL (OUT/IN) jacks.

– If your AV receiver is a Yamaha product and has the

capability to transmit SCENE control signals, you

can use the SCENE function.

Caution!

Do not connect the power cable of this

Player until all connections are completed.

Hints

– For details about the SCENE function, refer to the

owner’s manual supplied with your Yamaha AV

receiver.

– You can connect a Yamaha component (such as CD

player) corresponds with the SCENE function to the

REMOTE CONTROL (OUT) jack of this Player.

■ Connecting the power cable

– After all connections are completed, plug the

supplied power cable into the AC inlet on the rear of

the Player. Then plug into AC outlet.

Note

– TO PREVENT RISK OF ELECTRIC SHOCK, DO

NOT TOUCH THE UN-INSULATED PARTS OF

ANY CABLES WHILE THE POWER CABLE IS

CONNECTED.

OTHER CONNECTIONS

REMOTE CONTROL

OUT IN

NETWORK

USB BD STORAGE

REMOTE CONTROL IN

REMOTE CONTROL OUT

This Player

To REMOTE

CONTROL (IN)

jack

Monaural 3.5 mm mini

plug cable

(commercially available)

To remote

control out

jack

Yamaha component

To remote

control in

jack

Monaural 3.5 mm

mini plug cable

(commercially

available)

Infrared signal receiver

or Yamaha component

(such as AV receiver)

To REMOTE

CONTROL

(OUT) jack

To AC outlet

To AC inlet

16 En

PLAYBACK

■ Setting with the Initial Wizard/

Easy Setup

Initial Wizard/Easy Setup allows you to set language,

resolution, and screen aspect ratio easily. Initial Wizard

screen is displayed when you turn this Player on for the

first time after purchase or upgrade. Same setting can be

performed from SETUP menu = System = Easy Setup.

1 When Easy Setup screen is displayed, Press ENTER to

start Easy Setup.

2 Press 5 /a to select the language you want to display

on the screen, then press ENTER.

3 Press 5/a to select the resolution, then press ENTER.

For details on setting items, see “Resolution” (p. 28).

4 Press 5 /a to select the screen aspect ratio, then press

ENTER. For details on setting items, see “TV Screen”

(p. 28).

Easy Setup is completed.

Note

– When no picture is displayed after Initial Wizard/

Easy Setup is completed, refer to

“TROUBLESHOOTING” (p. 33).

INITIAL WIZARD/EASY SETUP

Sayfa yükleniyor ...

Yamaha BD-S667 El kitabı

Yamaha BD-S667 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler