Electrolux EW1289W Kullanım kılavuzu

Marka: Electrolux

Modeli: EW1289W

Kategori: Çamaşır makineleri

Tip: Kullanım kılavuzu

EW 1289 W

INSTRUCTION BOOKLET

KULLANIM KILAVUZU

WASHER-DRYER

KURUTMALI ÇAMAÇIR MAKINESI

132 991 030

132999190•EW1288W•cop 08/07/03 11:21 Pagina 1

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use environmentally

friendly paper.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 2 (Nero/Process Black pellicola)

ENGLISH

Contents

Operating sequence 19-21

Washing programmes 22

Drying programmes 23

International wash code symbols 24

Maintenance 25

Bodywork 25

Detergent dispenser drawer 25

Drain pump 25

Water inlet filter 26

Emergency emptying out 26

Frost precautions 26

Something not working? 27-28

Warnings 4-5

Disposal 5

Tips for environmental protection 5

Technical specifications 6

Installation 7

Unpacking 7

Positioning 7

Water inlet 7

Water drainage 8

Electrical connection 8

Your new washer-dryer 9

Description of the appliance 9

Door locked pilot light 9

Detergent dispenser drawer 9

Use 10

Control panel 10

Controls 10-14

Washing hints 15-16

Sorting the laundry 15

Temperatures 15

Before loading the laundry 15

Maximum loads 15

Laundry weights 15

Removing stains 15

Detergents and additives 16

Drying hints 17

Load 17

Garments not suitable for drying 17

Drying symbols on garment labels 17

Duration of the drying cycle 17

Fibre residue 17

Additional drying 17

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 3 (Nero/Process Black pellicola)

Installation

• All internal packing must be removed before using

the appliance. Serious damage may be caused to

the machine or adjacent furniture if the protective

transit devices are not removed or are not

completely removed. Refer to the relevant

paragraph in the instruction book.

• Any electrical work required to install this appliance

must be carried out by a qualified electrician.

• Any plumbing work required to install this

appliance must be carried out by a qualified

plumber.

• After having installed the machine, check that it is

not standing on its electrical supply cable.

• If the appliance is placed on a carpeted floor,

ensure that air can circulate freely between the

feet and the floor.

Use

• This appliance is designed for domestic use. It

must not be used for purposes other than those for

which it was designed.

• Only wash and dry fabrics which are designed to

be machine washed and dried. Follow the

instructions on each garment label.

• Do not overload the appliance. Follow the

instructions in the instruction book.

• Make sure that all pockets are empty. Objects such

as coins, safety pins, pins and screws can cause

extensive damage.

• Do not machine wash garments saturated with

petroleum, methylated spirits, trichlorethylene, etc.

If such fluids have been used to remove stains

prior to washing, wait until they have completely

evaporated from the fabric before placing

garments in the appliance.

• Place small items such as socks, belts, etc. in a

cloth bag or pillowcase to prevent them getting

trapped between the drum and the tub.

• If you use a liquid detergent with a dispenser which

has to be placed directly in the drum, remember to

remove this dispenser before drying.

Warnings

• Use only the recommended quantities of fabric

softener. An excessive amount could damage the

laundry.

• Leave the porthole door slightly ajar when the

appliance is not in use. This preserves the door

seal and prevents the formation of musty smells.

• Always check that water has emptied out before

opening the door. If not, drain the water following

the instructions in the instruction book.

• Always unplug the appliance and shut the water

tap after use.

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• During high temperature wash programmes and

during the drying cycle the door glass may get hot.

Do not touch it!

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 4 (Nero/Process Black pellicola)

ENGLISH

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded (for both washing and drying cycles).

• The machine will consume less energy if the

laundry is adequately spun before being dried.

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

• This machine incorporates a special child safety

feature to prevent small children from being

trapped inside the machine.

To activate this device, rotate the button (without

pressing it) inside the door clockwise until the

groove is horizontal. If necessary use a coin.

To disable this device and restore the possibility of

closing the door, rotate the button anti-clockwise

until the groove is vertical.

P1131

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 5 (Nero/Process Black pellicola)

DIMENSIONS Height 85 cm

Width 60 cm

Depth 60 cm

WASHING DRYING

MAXIMUM LOAD Cotton 5.5 kg 2.7 kg

Synthetics 3 kg 2 kg

Delicates 3 kg -

Woollens 2 kg -

SPIN SPEED 1200 rpm max.

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 50 kPa

Maximum 800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 6 (Nero/Process Black pellicola)

ENGLISH

Installation

Unpacking

All transit bolts and packing must be removed

before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

1. Using a spanner, unscrew and remove the two

rear bottom screws.Slide out the two plastic pins.

2. Lay the machine on its back, taking care not to

squash the hoses. This can be avoided by

placing one of the corner packing pieces between

the machine and the floor.

3. Remove the polystyrene block from the boottom

of the machine and release the two plastic bags.

4. Very carefully slide out the left polythene bag,

removing it towards the right and then

downwards.

5. Very carefully slide out the right polythene bag,

removing it towards the left and then upwards.

P1127

P1126

P1124

P0001

P1129

6. Set the machine upright and remove the

remaining rear screw. Slide out the relevant pin.

7. Plug the open holes with the plugs which you will

find in the plastic envelope containing the

instruction booklet.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with a 3/4"

thread.

Do not use already employed employed hoses.

The other end of the inlet hose which connects to the

machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks

P0021

P1088

P1051

P0002

P1128

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 7 (Nero/Process Black pellicola)

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked. Run it along the

floor; only the part near the drainage point must be

raised.

P0023

P0022

Electrical connection

This machine is designed to operate on a 220-230 V,

single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to comply

with the above safety precaution.

Shuold the appliance power supply cable need

to be replaced, this should be carried out by

our Service Centre.

The power supply cable must be easily

accessible after installing the machine.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 8 (Nero/Process Black pellicola)

ENGLISH

Your new washer-dryer

This new machine, which is fitted with the Direct Spray system, patented Electrolux, meets all modern needs

for effective treatment of laundry with low water, energy and detergent consumption.

Further savings are achieved by washing small loads of laundry, since water and electricity consumption is

proportional to the quantity and type of laundry being washed.

• The programme progress display shows the programme steps selected and the programme phase which

is running.

• The DELAY START option allows you to delay starting of the wash programme to the desired time of day.

• The RINSE HOLD function (stop with water in drum) can be selected for all fabrics: the laundry is left

immersed in the final rinse water to avoid the formation of creases.

• The special wool programme with its new delicate wash system treats your woollens with extreme care.

• The drying programmes will give your wash that soft, relaxed feel whatever the weather.

• 3-compartment drawer for detergent and fabric softner.

• The balance control device ensures the machine is stable during the spin.

1 Detergent dispenser drawer

2 Programme chart

3 Control panel

4 Door locked pilot light

5 Drain pump

6 Adjustable feet

Door locked pilot light

It stays on during the whole programme indicating

that the door is locked.

When the light goes out, the door can be opened

(see page 14).

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Description of the appliance

C0063

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 9 (Nero/Process Black pellicola)

Use

123456789101112

Control panel

1 ON/OFF button

Press this button to switch the machine on. The

display (8) will show three blinking dashes or a

blinking zero.You will find more detailed explanations

on page 12 (see DISPLAY).

Press it again to switch the machine off.

2 Mains-on light

This light comes on when the ON/OFF button is

pressed, and goes out when it is pressed again.

3 FABRIC button

Press this button repeatedly to select the programme

on the basis of the type of laundry to be washed. The

light relevant to the selected programme will light up.

The machine will propose a temperature and

automatically select the maximum spin value

provided for the programme you have chosen. You

can change these values by operating buttons 4 and

Hand wash

When you select this programme, you obtain a

particularly delicate washing, suitable for articles of

clothing whose label indicates that they must be

hand-washed

4 TEMPERATURE button

Press this button repeatedly to increase or decrease

the temperature, if you want your laundry to be

washed at a temperature different from the one

proposed by the washing machine. The relevant light

will light up.

Maximum temperatures are 95°C for cotton, 60°C for

synthetic fabrics,40°C for delicate fabrics, wool and

fabrics to be hand-washed(HAND WASH

programme).

Position SOGUK corresponds to a COLD WASH.

This option can be used for very delicate laundry,

such as curtains.

Important!

By depressing TEMPERATURE and SPIN SPEED

buttons simultaneously, the acoustic signal at the

end of the cycle is suppressed.

5 Spin speed button (DEVIR)

Press this button repeatedly to change the spin

speed, if you want your laundry to be spun at a

speed different from the one proposed by the

washing machine. The relevant light will light up.

Maximum speeds are:

• for cotton: 1,200 rpm;

• for synthetic fabrics, wool, and fabrics to be hand-

washed: 900 rpm;

• for delicate fabrics: 700 rpm.

RINSE HOLD position (SUDA BEKLETME): when

you choose this option, the machine will not drain the

water of the last rinse, so as not to wrinkle the

laundry.

At the end of the cycle, the light of the

START/PAUSE button(BAÇLAT/BEKLET) will flash,

to indicate that the water must be drained.

To complete the cycle, choose one of the following

options:

• Draining and spin:

- Press the START/PAUSE button. The machine

will drain the water, then spin the laundry at the

maximum speed provided for the performed

programme.

- Select spin speed by means of button 5, and

press the START/PAUSE button.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 10 (Nero/Process Black pellicola)

ENGLISH

• Drain only

- Press the SKIP/RESET button

(ILERLETME/IPTAL) once, so as tocause the

DRAIN light (BOSALTMA) to light up, then press

the START/PAUSE button.

Important!

If you accidentally press the SKIP/RESET button

more than once, the display will show three blinking

dashes. To cause the washing machine to drain the

water, select any washing programme by means of

the FABRIC button, then press SKIP/RESET three

times in order to select the DRAIN position (only the

DRAIN light will remain lit).START/PAUSE button.

6 OPTIONS button (SEÇENEKLER)

Press this button to select the following options:

• PREWASH (ÖN YIKAMA): select this option if you

wish your laundry to be prewashed before the

main wash (not available for wool and hand-

wash cycle).

The prewash ends with a short spin at 650 rpm in

programmes for cotton and synthetic fabrics,

whereas in the programme for delicate fabrics the

water is only drained.

• AA 40°: this option can be selected for cottons and

synthetics lightly or normally soiled with a

temperature of 40°C and higher.

If you select a temperature of 40°C, the machine

will prolong the time at 40°C in the washing

phase; this will allow an A class in energy

efficiency and washing performance to be

achieved.

If you select 90°C and press the AA 40° button,

the washing temperature will be reduced from

90°C to 60°C.

If you select 60°C and press the AA 40° button,

the washing temperature will be reduced from

60°C to 40°C. In both cases the washing time will

be prolonged.

• QUICK WASH (HIZLI YIKAMA) This button allows

you to select the QUICK WASH function, for

laundry that is only slightly soiled (not for wool and

HAND WASH programme).

The washing time will be reduced according to the

type of fabric and the selected temperature.

The PREWASH, AA 40° and QUICK options cannot

be selected together.

7 Electronic Drying button

(ELEKTRONIK KURUTMA)

By means of this button you can choose the required

degree of drying for cottons and synthetics:

Extra dry (cottons): Ekstra kurutma

Store dry (cottons and synthetics): Dolaplik kurutma

Iron dry (cottons): Ütü için kurutma

The corresponding pilot light illuminates.

The drying time is automatically adjusted by the

machine: the laundry will be dried to the selected

degree of dryness.

rying

Time button (KURUTMA

SÜRESI)

By depressing this button you can select a timed

programme for cotton or synthetics, the relevant light

illuminates. To select “cottons” you have to push the

button for about 2 seconds. To select the drying time

push the button until the time you want appears in

the display according to the fabrics (cotton or

synthetics) you have to dry.

- For COTTON you can select a drying time from 10

minutes to 2 hours and 10 minutes (2.10).

- For SYNTHETICS you can select a drying time

from 10 minutes to 1 hours and 40 minutes (1.40).

Every time you press the button the time increases,

by 5 mins.

9 DISPLAY

The following pieces of information are shown on the

display:

• Three blinking dashes, when a programme is

cancelled by means of the SKIP/RESET

(BASLAT/BEKLET) button.

The three blinking dashes will also appear when you

press the ON/OFF (AÇMA KAPAMA) button to

switch the machine on, if the previously selected

cycle has been erased.

---

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 11 (Nero/Process Black pellicola)

• Duration of washing programme in hours and

minutes, after you have selected a programme.

While the programme is running (after you have

pressed the START/PAUSE button

BASLAT/BEKLET), the displayed time value

decreases by one unit every minute.

• The selected drying time is displayed in minutes

or hours and minutes.

• The washing machine has stopped with water in

the tub, at the end of a programme with the RINSE

HOLD (SUDA BEKLETME) option: this is indicated

by a static zero.

• The washing machine has completed the

programme: this is indicated by a blinking zero. At

the same time, the door locked light goes out. The

zero will reappear when you switch the washing

machine on, unless the previous programme has

been erased by means of the SKIP RESET

(ILERLETME/IPTAL) button.

Important!

The first time you use the washing machine, when

you switch it on, it may display a blinking zero and

give an audible warning signal. This is due to the fact

that the washing machine has performed a washing

cycle during the manufacturer’s inspection tests, and

this cycle has not been erased after its completion.

1.25

2.05.

• Delay start, a time value indicated in hours and

selected by means of the relevant button

(GECIKTIRME).

The delay time is displayed for 5 seconds, then the

duration of the selected programme reappears.

After you have pressed the START/PAUSE button,

the countdown begins, and the delay time value

decreases by one unit every hour.

You can delay the start of the selected programme

by up to 24 hours in one hour intervals.

• An incorrect option selection has been made:

this is indicated by the message Err when a function

incompatible with the current programme is selected.

The incorrect selection is also indicated by an

audible warning signal.

• An alarm code indicates a fault in the machine

operation (see the relevant chapteron page 81).

E20

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 12 (Nero/Process Black pellicola)

ENGLISH

10 START/PAUSE button

(Baslat/Beklet)

This button has three functions:

• Start: after you have selected the desired

programme and options, press this button to start

the washing machine. The light above the button

will stop flashing and remain lit.

If you have selected a delay time by means of

button 11, the countdown will begin and will be

shown on the display.

• Pause: when you press this button again, the

programme in progressis interrupted. The light

above the button will start flashing. To restart the

programme, press the button again.

When you PAUSE the cycle, the DOOR LOCKED

light goes out, and it becomes possible to open the

door, provided

• the washing machine is not in the heating phase;

• the level of the water is not high;

• the drum is not turning.

Important!

You must set the washing machine to PAUSE before

you make any change in the programme in progress.

• Draining of water and spinning after the

execution of programmes with the RINSE HOLD

(SUDA BEKETME) option.

11 SKIP/RESET button

(ILERLETME/IPTAL)

At the end of a programme, you must press this

button once or repeatedly, in order to clear the

contents of the memory (the display will show three

blinking dashes); otherwise, the next time you switch

the washing machine on, the blinking zero will

reappear and the audible warning signals relevant to

the end of the previous cycle will be given.

You can also press the SKIP/RESET button to

exclude one or several phases of the programme

which is running, as indicated below.

- set the washing machine to PAUSE by pressing the

START/PAUSE button (the relevant light will flash);

- press the SKIP/RESET button once or several

times, until the required phase(s) is(are) cancelled

(the light next to the name of the phase(s) will go

out).

Example:

In this case, both the

drain and the spin (at the

speed provided for the

selected type of fabric)

will be performed.

This button allows you also to select special

programmes, such as RINSES, SPIN and DRAIN.

• If the machine is already switched on because it

has just performed a washing programme, proceed

as follows:

- depress SKIP/RESET once or repeatidly to cancel

the previously performed programme;

- select the type of fabric by means of button

“ÇAMASIR”;

- select the special programme:

• RINSES (DURULAMA)

Depress SKIP/RESET once, the pilot light

YIKAMA (WASH) goes out.

• SPIN (SIKMA)

Depress SKIP/RESET twice, the pilot lights

YIKAMA (WASH) and DURULAMA (RINSES) go

out.

• DRAIN (BOSALTMA)

Depress SKIP/RESET three times, the pilot lights

YIKAMA (WASH), DURULAMA (RINSES) and

SIKMA (SPIN) go out.

Example:

In this case the machine

will perform the rinses

followed by the spin.

display illuminates.

flash.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 13 (Nero/Process Black pellicola)

• If the machine is switched off:

- depress ON/OFF (AÇMA/KAPAMA) button to

switch it on;

- select the type of fabric by means of button

“ÇAMASIR”;

- select the special programme as previously

described.

12 DELAY START button

(GECIKTIRME)

This button makes it possible to delay the starting of

the programme by up to 24 hours. The delay you

have selected is shown on the display for about 5

seconds; afterwards, the duration of the programme

reappears.

You must select this option after you have set the

programme and before you press the

START/PAUSE button.

The time value shown on the display will decrease

by one unit every hour.

You can change the delay time at any moment,

before you press the START/PAUSE button.

If you have already pressed the START/PAUSE

button, and you wish to change or cancel the delay

time, proceed as follows:

• set the washing machine to PAUSE by pressing the

START/PAUSE button;

• press the DELAY button until the display shows the

desired delay time or

• press the DELAY button once, to erase the delay

time. The display will indicate “0h”.

• press the START/PAUSE button again.

Important!

The door will be locked throughout the delay time

(DOOR LOCKED

light lit).

If you need to open the door, you must first set the

washing machine

to PAUSE by pressing the START/PAUSE button.

After you have closed

the door, press the START/PAUSE button again.

13 Programme phase indicator

lights

When you select a programme, the lights relevant to

the phases that form the programme light up.

After you have started

the programme, only the

light relevant to the

phase that is currently

being carried out will

remain lit.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 14 (Nero/Process Black pellicola)

ENGLISH

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95° for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

60° for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g. underwear).

(cold)for delicate items (e.g. net curtains), mixed

30°-40° laundry including synthetic fibres

and woollens.

Before loading the laundry

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towelling towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 15 (Nero/Process Black pellicola)

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

residual marks with bleach.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 16 (Nero/Process Black pellicola)

ENGLISH

Drying hints

As a dryer, the machine works on the condensation

principle.

Therefore, the water tap must be open and the

drain hose must drain water into a sink or into

the drain pipe, even during the drying cycle.

Load

Warning:

Loads of washed laundry exceeding these values

must be divided before being dried, otherwise

poor results will be obtained.

Garments not suitable for drying

• Particularly delicate items such as synthetic

curtains, woollen and silk, garments with metal

inserts, nylon stockings, bulky garments such as

anoraks, bedcovers, quilts, sleeping bags and

duvets must not be machine dried.

• Garments padded with foam-rubber or materials

similar to foam-rubber must not be machine dried;

they represent a fire hazard.

• Also, fabrics containing residues of setting lotions

or hair sprays, nail solvents or similar solutions

must not be machine dried in order to avoid the

formation of harmful vapours.

Drying symbols on garment labels

Always look at the garment label to check whether

garments can be machine dried.

The following symbols refer to drying:

Machine drying is usually possible

Normal drying (normal temperature)

Gentle drying (reduced temperature)

Do not machine dry

Duration of the drying cycle

The drying time can vary according to

• the final spin speed;

• the required degree of drying (extra dry, store dry

or iron dry);

• the type of laundry;

• the size of load.

The usual drying times for the timed programmes are

indicated in the programme chart. As you become

more familiar with the appliance, you will discover

the drying times that best suit your needs according

to the various type of fabric. It is a good idea to make

a note of these times.

Fibre residue

After drying fluffy fabrics, such as new towels, it is

advisable to perform the rinse programme B to be

sure that any residue that may remain in the tub is

completely removed and does not stick to garments

dried afterwards.

After each drying cycle the filter should be

checked and cleaned.

Additional drying

Should the laundry still be too wet at the end of the

programme, set another short drying cycle.

Warning! To prevent the formation of creases or

shrinking of fabrics, avoid excessive drying.

max. load

(dry weight)

2,7 kg

2kg

Linen and cottons

Synthetics

Sort of laundry

132991030 EW1289W.qxd 08/07/2003 13:33 Pagina 17 (Nero/Process Black pellicola)

4.Switch the machine on

Press the ON/OFF button (AÇMA KAPAMA) to

switch the machine on.

The display will show three blinking dashes or a

blinking zero. The light above the button will light up.

5.Select the desired programme

Press the FABRIC button (ÇAMASIR) repeatedly, in

order to select the desired programme/ fabric.

The relevant light will light up.

The lights relevant to the phases that form the

programme will light up.

The display will show the duration of the selected

programme, calculated on the basis of the maximum

load for each type of fabric. The light of

START/PAUSE button will start flashing.

If the load of laundry to be washed is small, at the

beginning of the cycle the display will still indicate the

duration relevant to the maximum load. The duration

value will be gradually adjusted during the execution

of the cycle.

------

Operating sequence

Washing only

Before washing your first load of laundry, we

recommend that you run a cotton cycle at 60°C, with

the machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main wash

compartment and start up the machine.

1.Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2.Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you wish to carry out the prewash , pour detergent

into the appropriate compartment marked .

3.Measure out the additive

If required, pour fabric softener into the compartment

marked , without exceeding the «MAX» mark.

C0065

C0064

P0004

132991030 EW1289W.qxd 08/07/2003 13:34 Pagina 18 (Nero/Process Black pellicola)

ENGLISH

9. Select the DELAY TIME

Before you start the programme, if you wish the

starting to be delayed, press the DELAY button

GECIKTIRME repeatedly, or keep it pressed, to

select the desired delay.

The selected delay time value (up to 24 hours) will

appear on the display for 3 seconds, then the

duration of the programme will appear again.

10. Start the programme

Press the START/PAUSE button. The relevant light

will stop flashing, the DOOR LOCKED light will light

up, and only the light relevant to the phase that is in

progress will remain lit.

If you have chosen a delayed start, the washing

machine will begin the countdown.

The display will show the duration of the programme

or the selected delay.

11. How to change a programme

during its cycle

Before you make any change, you must pause the

washing machine by pressing the START/PAUSE

button.

It is possible to change any phase before the

programme carries it out.

Changing the type of fabric or temperature is

possible, obviously, only during the washing phase.

When you make a change in these twoparameters,

the washing machine will resume the cycle from the

beginning.

GECIKTIRME

6.Select the temperature

Press the TEMPERATURE button SICAKLIK if you

wish to select a temperature value different from the

one proposed by the washing machine or the COLD

WASH “SOGUK”. The relevant light will light up.

7. Select the spin speed RINSE

HOLD option (SUDA BEKLETME)

Press the SPIN SPEED button “DEVIR” repeatedly,

in order to select the desired spin speed or the

RINSE HOLD (SUDA BEKLETME) option. The

relevant light will light up.

If you select the RINSE HOLD option, the machine

will stop at the end of the programme with the water

still in the tub.

8.Select the desired options

If your laundry is very dirty, it may be advisable to

select the PREWASH option.

If your laundry is lightly or normally soiled and it is

necessary to prolonge the washing time, select the

AA40° option.

If your laundry is only slightly soiled, select the

QUICK option.

The relevant light illuminates.

132991030 EW1289W.qxd 08/07/2003 13:34 Pagina 19 (Nero/Process Black pellicola)

If it is necessary to drain the water in order to change

the programme in progress, proceed as follows:

• PAUSE the machine by pressing the

START/PAUSE button;

• press the SKIP/RESET button (ILERLETME/IPTAL)

repeatedly, until only the DRAIN light (BOSALTMA)

remains lit;

• press the START/PAUSE button again.

When the water has been drained, the display shows

a blinking zero.

You may now select a new programme and press

the START/PAUSE

button to start it.

12. How to cancel a programme

during its cycle

To cancel a programme that is being carried out, first

pause the washing machine by pressing the

START/PAUSE button , then press the SKIP/RESET

button (ILERLETME/IPTAL) repeatedly, until the

display shows three blinking dashes.

13. How to cancel a programme

during its cycle

You can open the door, after having set the washing

machine to PAUSE, provided the following

conditions exist:

• the washing machine is not in the heating phase

beyond 55°C;

• the level of the water is not high;

• the drum is not turning.

If these requirements are met, when you pause the

washing machine, the DOOR LOCKED light goes

out and the door can be opened.

Should it not be possible to open the door, and

should it be absolutely necessary to do so, switch

the machine off by pressing the ON/OFF button

“AÇMA/KAPAMA”.

After approximately 3 minutes, you can open the

door.

Pay attention to the level and temperature of the

water in the washing machine!

When you close the door and press the ON/OFF

button again, the washing machine will resume the

programme from the point where it had been

interrupted.

14. At the end of the programme

At the end of the programme, the washing machine

stops automatically, gives an audible signal, and

displays a blinking zero.

If you had selected the RINSE HOLD option, the

START/PAUSE button light flashes to indicate that

the water must be drained. The display shows a

steadily lit zero.

When the programme has been completed, a

blinking zero appears on the display and the audible

signal is given.

The DOOR LOCKED light goes out at once.

Press the SKIP/RESET button repeatedly to erase

the programme that has just been carried out. If

you omit to do this, the next time you switch the

washing machine on, the blinking zero will

appear on the display and you will hear the

audible signal.

Note: when you switch the machine on, if you must

erase the previously performed programme, it is also

sufficient to press the FABRIC button “ÇAMASIR”

and select a new programme.

Press the ON/OFF button to switch the machine off.

The relevant light will go out.

Remove the laundry from the washing machine.

Check whether the drum is completely empty, by

rotating it with your hand. The purpose of this is to

prevent any items of laundry from remaining

accidentally in the drum, where they might get

damaged in

a subsequent wash (e.g. by shrinking) or bleed

colour into another load of laundry.

We advise you to close the water supply tap and

disconnect the plug from the socket.

Leave the door ajar in order to air the washing

machine.

132991030 EW1289W.qxd 08/07/2003 13:34 Pagina 20 (Nero/Process Black pellicola)

Sayfa yükleniyor...

Electrolux EW1289W Kullanım kılavuzu

Marka: Electrolux

Modeli: EW1289W

Kategori: Çamaşır makineleri

Tip: Kullanım kılavuzu

PDF''yi indir

rapor

diğer dillerde

English: Electrolux EW1289W User manual

Electrolux EW1289W Kullanım kılavuzu

Electrolux EW1289W Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler