McQuay A5LCY10FR Yükleme Rehberi

INSTALLATION MANUAL

IM-5WMYJ-1110(0)-ACSON

Part No.:R08019035855

INVERTER WALL MOUNTED

SPLIT TYPE AIR CONDITIONER

(L Series)

Acson IM-WMJ-1110(0).indd 1Acson IM-WMJ-1110(0).indd 1 1/12/2011 6:24:46 PM1/12/2011 6:24:46 PM

Acson IM-WMJ-1110(0).indd 2Acson IM-WMJ-1110(0).indd 2 1/12/2011 6:24:48 PM1/12/2011 6:24:48 PM

1-1

h

s

i

l

g

nE

English

Indoor Unit [A5WMYL Series]

OUTLINE AND DIMENSIONS

A

B

C

H

I

B

F

E

J

G

L

D

B

K

M

A

F

A B C D E F G H I J K L M

800 288 206 166 184 42 46 55 56 154 182 263 52

Dimension

A5WMY10/15LR

THE MARK SHOWS PIPING DIRECTION

REAR REAR

LEFT RIGHT

TOP VIEW

BOTTOMBOTTOM

LOUVER FRONT GRILLE FIXED

SCREWS (INSIDE)

FRONT VIEW

SIGNAL RECEIVER

INDOOR UNIT

ON/OFF SWITCH

ROOM TEMPERATURE

THERMIRTOR (INSIDE)

SIDE VIEW

NAME PLATE

TERMINAL

BLOCK

WITH EARTH

TERMINAL

Use tape measure

as shown.

Position the end

of a tape measure

at

X

Recommended mounting

plate retention spots

(5 spots in all)

Liquid pipe end Gas pipe end

INSTALLATION PLATE All dimensions are in mm

Through the wall

hole Ø 65mm

Drain hose

position

Model

Original Instruction

Acson IM-WMJ-1110(0).indd Sec1:1Acson IM-WMJ-1110(0).indd Sec1:1 1/12/2011 6:24:48 PM1/12/2011 6:24:48 PM

1-2

Outdoor Unit [A5LCY10/15FR]

All dimensions are in mm

E

D

BC

IH

G

N

J

LK

F

A

ABCDEFGH I JKLMN

A5LCY10/15FR 550 658 51 11 273 16 14 470 96 299 94 60 14 133

Dimension

Model

Acson IM-WMJ-1110(0).indd Sec1:2Acson IM-WMJ-1110(0).indd Sec1:2 1/12/2011 6:24:48 PM1/12/2011 6:24:48 PM

1-3

h

s

i

l

g

nE

English

INSTALLATION MANUAL

This manual provides the procedures of installation to ensure a safe and good standard of operation for the air

conditioner unit.

Special adjustment may be necessary to suit local requirements.

Before using your air conditioner, please read this instruction manual carefully and keep it for future reference.

This appliance is intended to be used by expert or trained users in shops, in light industry and on farms, or for

commercial use by lay persons.

WARNING

• Installation and maintenance should be performed by

qualiﬁ ed persons who are familiar with local code and

regulation, and experienced with this type of appliance.

• All ﬁ eld wiring must be installed in accordance with the

national wiring regulation.

• Ensure that the rated voltage of the unit corresponds to

that of the name plate before commencing wiring work

according to the wiring diagram.

• The unit must be GROUNDED to prevent possible hazard

due to insulation failure.

• All electrical wiring must not touch the refrigerant piping

or any moving parts of the fan motors.

• Conﬁ rm that the unit has been switched OFF before

installing or servicing the unit.

• Disconnect from the main power supply before servicing

the air conditioner unit.

• DO NOT pull out the power cord when the power is ON.

This may cause serious electrical shocks which may

result in ﬁ re hazards.

• Keep the indoor and outdoor units, power cable and

transmission wiring, at least 1m from TVs and radios, to

prevent distorted pictures and static. {Depending on the

type and source of the electrical waves, static may be

heard even when more than 1m away}.

CAUTION

Please take note of the following important points

when installing.

• Do not install the unit where leakage of ﬂ ammable

gas may occur.

If gas leaks and accumulates around the unit, it

may cause ﬁ re ignition.

• Ensure that drainage piping is connected properly.

If the drainage piping is not connected properly, it

may cause water leakage which will dampen the

furniture.

• Do not overcharge the unit.

This unit is factory pre-charged. Overcharge will

cause over-current or damage to the compressor.

• Ensure that the unit’s panel is closed after service or

installation.

Unsecured panels will cause the unit to operate

noisily.

• Sharp edges and coil surfaces are potential locations

which may cause injury hazards. Avoid from being in

contact with these places.

• Before turning off the power supply, set the remote

controller’s ON/OFF switch to the “OFF” position to

prevent the nuisance tripping of the unit. If this is not

done, the unit’s fans will start turning automatically when

power resumes, posing a hazard to service personnel or

the user.

• Do not install the units at or near doorway.

• Do not operate any heating apparatus too close to the

air conditioner unit or use in room where mineral oil, oil

vapour or oil steam exist, this may cause plastic part to

melt or deform as a result of excessive heat or chemical

reaction.

• When the unit is used in kitchen, keep ﬂ our away from

going into suction of the unit.

• This unit is not suitable for factory used where cutting oil

mist or iron powder exist or voltage ﬂ uctuates greatly.

• Do not install the units at area like hot spring or oil

reﬁ nery plant where sulphide gas exists.

• Ensure the color of wires of the outdoor unit and the

terminal markings are same to the indoors respectively.

• IMPORTANT : DO NOT INSTALL OR USE THE AIR

CONDITIONER UNIT IN A LAUNDRY ROOM.

• Do not use joined and twisted wires for incoming power

supply.

• For any enquiries on spare part, please contact your

authorized dealer.

• The equipment is not intended for use in a potentially

explosive atmosphere.

SAFETY PRECAUTIONS

NOTICE

Disposal requirements

Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not

be mixed with unsorted household waste.

Do not try to dismantle the system yourself: the dismantling of the air conditioning system, treatment of the refrigerant,

of oil and of other parts must be done by a qualiﬁ ed installer in accordance with relevant local and national legislation.

Air conditioners must be treated at a specialized treatment facility for re-use, recycling and recovery. By ensuring this

product is disposed of correctly, you will help to prevent potential negative consequences for the environment and

human health. Please contact the installer or local authority for more information.

Batteries must be removed from the remote controller and disposed of separately in accordance with relevant local

and national legislation.

Acson IM-WMJ-1110(0).indd Sec1:3Acson IM-WMJ-1110(0).indd Sec1:3 1/12/2011 6:24:49 PM1/12/2011 6:24:49 PM

1-4

IMPORTANT

Important information regarding the refrigerant used

This product contains ﬂ uorinated greenhouse gases covered by the Kyoto Protocol.

Do not vent gases into the atmosphere.

Refrigerant type: R410A

GWP

(1)

value: 1975

(1)

GWP = global warming potential

Please ﬁ ll in with indelible ink,

■ A the factory refrigerant charge of the product,

■ B the additional refrigerant amount charged in the ﬁ eld and

■ A + B the total refrigerant charge

on the refrigerant charge label supplied with the product.

The ﬁ lled out label must be adhered in the proximity of the product charging port (e.g. onto the inside of the service

cover).

1 factory refrigerant charge of the product:

see unit name plate

(2)

2 additional refrigerant amount charged in the ﬁ eld

3 total refrigerant charge

4 contains ﬂ uorinated greenhouse gases covered by the Kyoto Protocol

5 outdoor unit

6 refrigerant cylinder and manifold for charging

(2)

In case of multiple indoor systems, only 1 label must be adhered*, mentioning the total factory refrigerant charge of

all indoor units connected in the refrigerant system.

Periodical inspections for refrigerant leaks may be required depending on European or local legislation. Please

contact your local dealer for more information.

* on the outdoor unit

Acson IM-WMJ-1110(0).indd Sec1:4Acson IM-WMJ-1110(0).indd Sec1:4 1/12/2011 6:24:49 PM1/12/2011 6:24:49 PM

1-5

h

s

i

l

g

nE

English

INSTALLATION DIAGRAM

.

INSTALLATION OF THE OUTDOOR UNIT

• Where a wall or other obstacle is in the path of outdoor unit’s intake or exhaust airflow, follow the installation guidelines below.

• For any of the below installation patterns, the wall height on the exhaust side should be 1200mm or less.

n 50ahteroM n 50ahteroM

More than 150

More than

100

More than 50 More than 100

Side view

1200

or less

Wall facing one side Walls facing two sides

Top view

unit: mm

More than 150

More than 300

More than 50

Walls facing three sides

Indoor Unit

30mm or more from ceiling

Front Panel

50mm or more from walls

(on both sides)

Air ﬁ lter

Outdoor Unit

Caulk pipe

hole gap

with putty.

Cut thermal insulation pipe to

an appropriate length and wrap

it with tape, making sure that no

gap is left in the insulation pipe’s

cut line.

Wrap the insulation pipe with the

ﬁ nishing tape from bottom to top.

Service lid

• Opening service lid

Service lid is opening/closing

type.

• Opening method

1) Remove the service lid

screws.

2) Pull out the service lid

diagonally down in the direction

of the arrow.

3) Pull down.

250mm from wall

M4 X 12L

Acson IM-WMJ-1110(0).indd Sec1:5Acson IM-WMJ-1110(0).indd Sec1:5 1/12/2011 6:24:49 PM1/12/2011 6:24:49 PM

1-6

Drain work. (Heat Pump Unit Only)

1) Use drain plug for drainage.

2) If the drain port is covered by a mounting base or ﬂ oor surface, place

additional foot bases of at least 30mm in height under the outdoor unit’s

feet.

3) In cold areas, do not use a drain hose with the outdoor unit.

(Otherwise, drain water may freeze, impairing heating performance.)

INSTALLATION OF THE INDOOR UNIT

The indoor unit must be installed in such a way so as to

prevent short circuit of the cool discharged air with the hot

return air. Please follow the installation clearance shown

in the ﬁ gure. Do not place the indoor unit where there

could be direct sunlight shining on it. Also, this location

must be suitable for piping and drainage, and be away

from doors or windows.

The refrigerant piping can be routed to the unit in a

number of ways (left or right from the back of the unit), by

using the cut-out holes on the casing of the unit.

Bend the pipes carefully to the required position in order

to align it with the holes. For the side and bottom out,

hold the bottom of the piping and then position it to the

required direction. The condensation drain hose can be

taped to the pipes.

All dimensions are in mm

Drain water hole

Bottom frame

Drain plug

Hose (available commercially,

inner dia. 16mm)

Air ﬂ ow

(Indoor)

min. 50 min. 50

(Space for

maintenance)

(Space for

maintenance)

Required space

min. 30

(Space for

performance)

Right-side, right-back or right-bottom piping

Remove pipe port cover

here for right-side piping

Remove pipe port cover

here for right-bottom piping

Bind coolant pipe and

drain hose together

with insulating tape.

Left-side, left-back or left-bottom piping

Right-side

piping

Right-back piping

Left-back piping

Left-side piping

Left-bottom piping

Remove pipe port cover

here for left-side piping

Remove pipe port cover here for left-bottom

piping

Right-bottom

piping

Acson IM-WMJ-1110(0).indd Sec1:6Acson IM-WMJ-1110(0).indd Sec1:6 1/12/2011 6:24:49 PM1/12/2011 6:24:49 PM

1-7

h

s

i

l

g

nE

English

Mounting Installation Plate

Ensure that the wall is strong enough to withstand the

weight of the unit. Otherwise, it is necessary to reinforce

the wall with plates, beams or pillars.

Use the level gauge for horizontal mounting, and ﬁ x it

with 5 suitable screws.

In case the rear piping draws out, drill a hole 65mm in

diameter with a cone drill, slightly lower on the outside

wall (see ﬁ gure).

166

184

181.7

55.554.5

153.8

263

51.9

800

9

.5

4

2

.2

4

882

2.24

9.54

Recommended Mounting Plate Retention Spots And

Dimensions

Mount The Unit Onto The Installation Plate

Hook the indoor unit onto the upper portion of the

installation plate (Engage the two hooks at the rear top

of the indoor unit with the upper edge of the installation

plate). Ensure that the hooks are properly seated on the

installation plate by moving it to the left and right.

How To Attach The Indoor Unit

Hook the claws of the bottom frame to the mounting

plate.

How To Remove The Indoor Unit

Push up the marked area (at the lower part of the front

grille) to release the claws.

Water Drainage Piping

The indoor drain pipe must be in a downward gradient for

smooth drainage. Avoid situations that are likely to cause

water to leak.

• Do not install the unit at altitude over 2000m for both

indoor & outdoor.

CAUTION

Mounting plate

ﬁ xing screw

Mounting plate

Clip

Mark (Rear side)

Bottom frame

Front grille

When stripping the ends

of interconnecting wires in

advance, bind right ends

of wires with insulating

tape.

Mounting plate

Hand indoor unit’s hook here.

Wire guide

Interconnecting

wires

Water Drainage

Correct Wrong Wrong Wrong

Water

Leaking

Water

Leaking

Water

Leaking

Water

Retention

End

dipped

into

water

Drain

Recommended mounting plate

retention spots (5 spots in all)

Use tape measure as shown.

Position the end of a tape

measure at

X

Through

the wall

hole

Ø 65mm

Drain

hose

position

Gas pipe endLiquid pipe end

All dimensions are in mm

Hole with cone drill

Wall embedded pipe

(Field supply)

Caulking

OutsideInside

Ø 65

Wall embedded pipe

(Field supply)

Wall hole cover

(Field supply)

Acson IM-WMJ-1110(0).indd Sec1:7Acson IM-WMJ-1110(0).indd Sec1:7 1/12/2011 6:24:49 PM1/12/2011 6:24:49 PM

1-8

REFRIGERANT PIPING

Allowable Piping Length

If the pipe is too long, both the capacity and reliability of

the unit will drop. As the number of bends increases,

resistance to the ﬂ ow of refrigerant system increases, thus

lowering cooling capacity. As a result, the compressor

may become defective. Always choose the shortest path

and follow the recommendations as tabulated below:

Model

Min. Allowable Length, m

Max. Allowable Length, m

Additional charge of refrigerant

Max. Allowable Elevation, m

Gas Pipe Size, mm/(in)

Liquid Pipe Size

, mm/(in)

10 15

3

15

20

10

9.52 (3/8")

6.35 (1/4")

*Be sure to add the proper amount of additional refrigerant.

Failure to do so may result in reduced performance.

Remark: The refrigerant pre-charged in the outdoor

unit is for piping length up to 7.5m.

Piping Works and Flaring technique

• Do not use contaminated or damaged copper tubing. If

any piping, evaporator or condenser had been exposed

or had been opened for 15 seconds or more, the system

must be vacuumed. Generally do not remove plastic,

rubber plugs and brass nuts from the valves, ﬁ ttings,

tubing and coils until it is ready to connect suction or

liquid line into valves or ﬁ ttings.

• If any brazing work is required, ensure that nitrogen

gas is passed through coil and joints while the brazing

work is being done. This will eliminate soot formation

on the inside wall of copper tubings.

• Cut the pipe stages by stages, advancing the blade of

pipe cutter slowly. Extra force and a deep cut will cause

more distortion of pipe and therefore extra burr. See

Figure A.

• Remove burrs from cut edges of the pipes with remover.

See Figure B. Hold the pipe on top position and burr

removel at lower position to prevent metal chips from

entering the pipe. This will avoid unevenness on the

ﬂ are faces which will cause gas leak.

• Insert the ﬂ are nuts, mounted on the connection parts

of both the indoor unit and outdoor unit, into the copper

pipes.

• The exact length of pipe protruding from the top surface

of the swaging block is determined by the ﬂ aring tool.

See Figure C.

• Fix the pipe ﬁ rmly on the swaging block. Match the

centers of both the swaging block and the ﬂ aring punch,

then tighten the ﬂ aring punch fully.

• The refrigerant pipe connection are insulated by closed

cell polyurethane.

Piping Connection To The Units

• Align the center of the piping and tighten the ﬂ are nut

sufﬁ ciently with ﬁ ngers. See Figure D.

• Finally, tighten the ﬂ are nut with torque wrench until the

wrench clicks.

• When tightening the ﬂ are nut with the torque wrench,

ensure that the tightening direction follows the arrow

indicated on the wrench.

• The refrigerant pipe connection are insulated by closed

cell polyurethane.

Pipe Size, mm (in) Torque, Nm / (ft-Ib)

6.35 (1/4") 18 (13.3)

9.52 (3/8") 42 (31.0)

12.70 (1/2") 55 (40.6)

15.88 (5/8") 65 (48.0)

19.05 (3/4") 78 (57.6)

Ø Tube, D A (mm)

Inch mm Imperial

(Wing-nut Type)

Rigid

(Clutch Type)

1/4" 6.35 1.3 0.7

3/8" 9.52 1.6 1.0

1/2" 12.70 1.9 1.3

5/8" 15.88 2.2 1.7

3/4" 19.05 2.5 2.0

Figure A

Figure B

Figure C

Figure D

Flared Tube

Flare Joint

Flare Nut

Indoor Piping

Torque Wrench

Spanar

Copper Tube

Swaging Block

1/4t

Cutting Copper Tube

Remove Burr

A

D

Acson IM-WMJ-1110(0).indd Sec1:8Acson IM-WMJ-1110(0).indd Sec1:8 1/12/2011 6:24:50 PM1/12/2011 6:24:50 PM

1-9

h

s

i

l

g

nE

English

ELECTRICAL WIRING CONNECTION

IMPORTANT :* The ﬁ gures shown in the table are for information purpose only. They should be checked and

selected to comply with the local/national codes of regulations. This is also subject to the type of

installation and conductors used.

** The appropriate voltage range should be checked with label data on the unit.

• All wires must be ﬁ rmly connected.

• Make sure all the wire do not touch the refrigerant pipings, compressor or any moving parts.

• The connecting wire between the indoor unit and the outdoor unit must be clamped by using provided cord

anchorage.

• The power supply cord must be equivalent to H07RN-F which is the minimum requirement.

• Make sure no external pressure is applied to the terminal connectors and wires.

• Make sure all the covers are properly ﬁ xed to avoid any gap.

• Use round crimp-style terminal for connecting wires to the power supply terminal block. Connect the wires by

matching to the indication on terminal block. (Refer to the wiring diagram attached on the unit.)

* If the length of the cable is more than 2m, use cable

with bigger size.

1

2

SIG

N

L

2

1

SIG

Indoor Unit

Terminal Block

Outdoor Unit

Terminal Block

Power Supply

Cable

There must be an all pole disconnection

in the supply mains with a contact

seperation of at least 3mm.

Model 10

Voltage range**

Power supply cable size* mm²

Number of core

Interconnection cable size* mm²

Number of core

Recommended time delay fuse A

1.5

3

1.5

4

15

1.5

3

1.5

4

15

220V - 240V / 1Ph / 50Hz+

• Used the correct screwdriver for terminal screws tightening. Unsuitable screwdrivers can damage the screw head.

• Over tightening can damage the terminal screws.

• Do not connect wire of different gauge to same terminal.

• Keep wiring in an orderly manner. Prevent the wiring from obstructing other parts and the terminal box cover.

Attach insulation sleeve

Round crimp-style terminal

Electric wire

Connect wires of the

same gauge to both side.

Do not connect wires of the

same gauge to one side.

Do not connect wires

of different gauges.

Acson IM-WMJ-1110(0).indd Sec1:9Acson IM-WMJ-1110(0).indd Sec1:9 1/12/2011 6:24:50 PM1/12/2011 6:24:50 PM

1-10

SPECIAL PRECAUTIONS WHEN DEALING WITH R410A UNIT

R410A is a new HFC refrigerant which does not damage

the ozone layer. The working pressure of this new

refrigerant is 1.6 times higher than conventional refriger-

ant (R22), thus proper installation / servicing is essential.

• Never use refrigerant other than R410A in an air

conditioner which is designed to operate with R410A.

• POE or PVE oil is used as lubricant for R410A

compressor, which is different from the mineral oil used

for R22 compressor. During installation or servicing,

extra precaution must be taken not to expose the

R410A system too long to moist air. Residual POE or

PVE oil in the piping and components can absorb

moisture from the air.

• To prevent mischarging, the diameter of the service

port on the flare valve is different from that of R22.

• Use tools and materials exclusively for refrigerant

R410A. Tools exclusively for R410A are manifold valve,

charging hose, pressure gauge, gas leak detector, flare

tools, torque wrench, vacuum pump and refrigerant

cylinder.

• As an R410A air conditioner incurs higher pressure

than R22 units, it is essential to choose the copper

pipes correctly. Never use copper pipes thinner than

0.8mm even though they are available in the market.

• If the refrigerant gas leakage occurs during installation /

servicing, be sure to ventilate fully. If the refrigerant gas

comes into contact with fire, a poisonous gas may

occur.

• When installing or removing an air conditioner, do not

allow air or moisture to remain in the refrigerant cycle.

Refrigerant Piping

Outdoor Unit 3 ways valve

Allen key

Service Port

Flare nut

HIGH PRESSURE GAUGE

GAUGE MANIFOLD

LOW PRESSURE GAUGE

HANDLE HI (ALWAYS CLOSED)

CHARGE HOSE

-760mmHg

HANDLE LO

CHARGE HOSE

VACUUM PUMP

ADAPTER FOR

COUNTER FLOW

PREVENTION

CHECK VALVE

LIQUID VALVE

HIGH PRESSURE GAUGE

LOW PRESSURE GAUGE

GAUGE MANIFOLD

-760mmHg

HANDLE LO

HANDLE HI (ALWAYS CLOSED)

CHARGE HOSE

CHECK VALVE

LIQUID VALVE

GAS VALVE

(3-WAY)

CONFIGURATION OF AIR

PURGE BY CHARGING

CONFIGURATION OF AIR

PURGE BY CHARGING

GAS VALVE

(3-WAY)

Vacuuming The Piping And The Indoor Unit

Vacuuming is necessary to eliminate all moisture and air from the system.

VACUUMING AND CHARGING

Except for the outdoor unit which is pre-charged with

refrigerant, the indoor unit and the refrigerant connection

pipes must be air-purged because the air containing

moisture that remains in the refrigerant cycle may cause

malfunction of the compressor.

• Remove the caps from the valve and the service port.

• Connect the center of the charging gauge to the

vacuum pump.

• Connect the charging gauge to the service port of the

3-way valve.

• Start the vacuum pump. Evacuate for approximately 30

minutes. The evacuation time varies with different

vacuum pump capacity. Confirm that the charging

gauge needle has moved towards -760mmHg.

Caution

• If the gauge needle does not move to -760mmHg, be

sure to check for gas leaks (using the refrigerant

detector) at flare type connection of the indoor and

outdoor unit and repair the leak before proceeding to

the next step.

• Close the valve of the changing gauge and stop the

vacuum pump.

• On the outdoor unit, open the suction valve (3 way)

and liquid valve (2 way) (in anti-clockwise direction)

with 4mm key for hexagon sacked screw.

Charge Operation

This operation must be done by using a gas cylinder and

a precise weighing machine. The additional charge is

topped-up into the outdoor unit using the suction valve via

the service port.

• Remove the service port cap.

• Connect the low pressure side of the charging gauge to

the suction service port center of the cylinder tank and

close the high pressure side of the gauge. Purge the air

from the service hose.

• Start the air conditioner unit.

• Open the gas cylinder and low pressure charging valve.

• When the required refrigerant quantity is pumped into

the unit, close the low pressure side and the gas

cylinder valve.

• Disconnect the service hose from service port. Put back

the service port cap.

Acson IM-WMJ-1110(0).indd Sec1:10Acson IM-WMJ-1110(0).indd Sec1:10 1/12/2011 6:24:51 PM1/12/2011 6:24:51 PM

1-11

h

s

i

l

g

nE

English

INDICATOR LIGHTS

IR Signal Receiver

When an infrared remote control operating signal has

been transmitted, the signal receiver on the indoor unit

will respond as below to conﬁ rm acceptance of the signal

transmission.

ON to OFF

OFF to ON

Pump down / Cool force on

Others

1 Long Beep

2 Short Beep

1 Short Beep

Cooling Unit / Heat Pump Unit

The table shows the LED indicator lights for the air

conditioner unit under normal operation and fault

conditions. The LED indicator lights are located at the

side of the air conditioner unit.

The heat pump units are equipped with an “auto” mode

sensor whereby it will provide reasonable room

temperature by switching automatically to either “cool”

or “heat” mode according to the temperature set by the

user.

LED Indicator Lights for Cooling Unit / Heat Pump

Unit

LED Indicator Lights : Normal Operation & Fault Condition For Cooling / Heat Pump Unit

COOL/HEAT

(GREEN/RED)

GREEN

RED

Operation

Cool mode

Heat mode

Auto mode in Heating operation

Auto mode in Cooling operation

Timer on

Sleep mode on

Fan mode on

Dry mode on

Defrost operation

ON

Blinking

IR Receiver

Cool / Heat

Timer

Sleep

ON/OFF switch

GREEN

Unit error

IR Receiver

Acson IM-WMJ-1110(0).indd Sec1:11Acson IM-WMJ-1110(0).indd Sec1:11 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

1-12

OPERATING RANGE

COOLING HEATING

INDOOR TEMP. (°CWB) INDOOR TEMP. (°CDB)

DB: Dry bulb WB: Wet bulb

AIR FILTER

1. Open the front panel.

• Hold the panel at the recesses on the main unit (2

recesses on right and left sides) and lift it until it

stops.

2. Pull out the air ﬁ lters.

• Push a little upwards the tab at the center of each

air ﬁ lter, then pull it down.

3. Clean or replace each ﬁ lter.

• When shaking off remaining water, do not wring the

ﬁ lter.

4. Set the air ﬁ lter and close the front panel.

• Insert claws of the ﬁ lters into slots of the front panel.

Close the front panel slowly and push the panel at

the 3 points. (1 on each side and 1 in the middle.)

• The air ﬁ lter have a symmetrical form in the horizontal

direction.

FRONT

Process on

main unit

OUTDOOR TEMP. (°CDB)

OUTDOOR TEMP. (°CWB)

Acson IM-WMJ-1110(0).indd Sec1:12Acson IM-WMJ-1110(0).indd Sec1:12 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

1-13

h

s

i

l

g

nE

English

SERVICE AND MAINTENANCE

Service Parts

Indoor air ﬁ lter

Indoor unit

Maintenance Procedures Period

1. Remove any dust adhering to the ﬁ lter by using a vacuum cleaner or wash in

lukewarm water (below 40°C/104°F) with a neutral cleaning detergent.

2. Rinse the ﬁ lter well and dry before placing it back onto the unit.

3. Do not use gasoline, volatile substances or chemicals to clean the ﬁ lter.

1. Clean any dirt or dust on the grille or panel by wiping it with a soft cloth

soaked in lukewarm water (below 40°C/104°F) and a neutral detergent

solution.

2. Do not use gasoline, volatile substances or chemicals to clean the indoor

unit.

At least once every 2

weeks.

More frequently if

necessary.

At least once every 2

weeks.

More frequently if

necessary.

Recess on

main unit

Rotating

shaft

1. Open the front panel.

• Hold the panel at the recesses on the main unit (2

recesses on right and left sides) and lift it until it

stops.

2. Remove the front panel.

• While lifting the front panel further, slide it to the right

and pull it to the front side. The left rotating shaft is

detached. Slide the right rotating shaft to the left and

pull it to the front side to remove it.

3. Attach the front panel.

• Align the right and left rotating shafts of the front

panel with the grooves and push them all the way

in.

• Gently close the front panel. (Push both ends and

the center on the front panel.)

• Do not touch the metal parts of the indoor unit. It may cause an injury.

• When removing or attaching the front panel, support the panel securely with hand to prevent it from falling.

• For cleansing, do not use hot water above 40°C, benzine, gasoline, thinner, nor other volatile oils, polishing

compound, scrubbing brushes, nor other hand stuff.

• After cleaning, make sure that the front panel is securely ﬁ xed.

CAUTION

When The Unit Is Not To Be Used For An Extended Long Period Of Time

Operate the unit for 2 hours

with the following setting.

Operating mode : cool

Temperature : 30°C/86°F

Remove the power plug.

If you are using an independent

electric circuit for your unit, cut

off the circuit.

Remove the batteries in the

remote control.

• Avoid direct contact of any coil treatment cleaners on plastic part. This may cause plastic part to deform as a

result of chemical reaction.

CAUTION

Acson IM-WMJ-1110(0).indd Sec1:13Acson IM-WMJ-1110(0).indd Sec1:13 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

1-14

MEMO

Acson IM-WMJ-1110(0).indd Sec1:14Acson IM-WMJ-1110(0).indd Sec1:14 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

1-15

h

s

i

l

g

nE

English

MEMO

Acson IM-WMJ-1110(0).indd Sec1:15Acson IM-WMJ-1110(0).indd Sec1:15 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

1-16

MEMO

Acson IM-WMJ-1110(0).indd Sec1:16Acson IM-WMJ-1110(0).indd Sec1:16 1/12/2011 6:24:52 PM1/12/2011 6:24:52 PM

hs

i

l

g

nE

Italiano

2-1

H

I

F

E

J

G

L

D

B

K

M

A

F

A

B

C

B

Unità Interna [Serie A5WMYL]

DISEGNI E DIMENSIONI

IL SEGNO MOSTRA LA DIREZIONE DEI TUBI

Dimensioni

Modello

ABCDEFGHI JKL M

A5WMY10/15LR 800 288 206 166 184 42 46 55 56 154 182 263 52

Istruzioni originali

DIETRO DIETRO

SINISTRA DESTRA

VISTA DALL’ALTO

IN

BASSO

IN

BASSO

FERITOIA DI

AERAZIONE

VITI INSERITE NELLA GRIGLIA

FRONTALE (ALL’INTERNO)

VISTA FRONTALE

RICEVITORE DI

SEGNALE

UNITÀ INTERNA

INTERRUTTORE ON/OFF

TEMPERATURA

AMBIENTE TERMISTORE

(ALL’INTERNO)

VISTA LATERALE

PIASTRA

MORSETTIERA

CON TERMINALE

A TERRA

Usare la misura del nastro

come posizione che indica

la ﬁ ne del nastro a



Punti di ritenzione raccomandati

per la piastra di montaggio

(5 punti in tutto)

Estremità del tubo del liquido Estremità del tubo del gas

LASTRA DI INSTALLAZIONE Tutte le dimensioni sono in mm

Foro nel muro di

Ø 65mm

Posizione del

tubo di scarico

Acson IM-WMJ-0111(0)_IT.indd 1Acson IM-WMJ-0111(0)_IT.indd 1 1/12/2011 12:02:31 PM1/12/2011 12:02:31 PM

2-2

Unità Esterna [Serie A5LCY10/15FR]

Dimensioni

Modello

ABCDEFGH I J KLMN

A5LCY10/15FR 550 658 51 11 273 16 14 470 96 299 94 60 14 133

E

D

B C

IH

G

N

J

LK

F

A

Tutte le dimensioni sono in mm

Acson IM-WMJ-0111(0)_IT.indd 2Acson IM-WMJ-0111(0)_IT.indd 2 1/12/2011 12:02:32 PM1/12/2011 12:02:32 PM

Sayfa yükleniyor ...

McQuay A5LCY10FR Yükleme Rehberi

Bu kılavuz için de uygundur

McQuay A5LCY10FR Yükleme Rehberi

Diğer dillerde

İlgili Makaleler

Diğer Belgeler