Yamaha MCR-B020 El kitabı

Integrated Amplifier

Amplificateur Intégré

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G

Printed in China MCR-B020/G-1

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

Micro Component System

Micro-Chaîne

English Français Deutsch Svenska Italiano Español Nederlands Русский

MCR-B020_G-cv.fm Page 1 Tuesday, November 15, 2016 3:42 PM

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place -

away from direct sunlight, heat sources, vibration, dust,

moisture and cold. For proper ventilation, allow the

following minimum clearances.

Top: 15 cm (6 in)

Rear: 10 cm (4 in)

Sides: 10 cm (4 in)

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot, and do not locate this unit in an

environment with high humidity (i.e. a room with a

humidifier) to prevent condensation inside this unit, which

may cause an electrical shock, fire, damage to this unit,

and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage other

than specified.

13 To prevent damage by lightning, keep the power cable

disconnected from a wall outlet or this unit during a

lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed.

The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the

wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press to set the unit to off,

and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become

warm. Turn off, then leave this unit alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like. When you dispose of

batteries, follow your regional regulations.

– Keep the batteries in a location out of reach of children.

Batteries can be dangerous if a child were to put in his or

her mouth.

– If the batteries grow old, the effective operation range of

the remote control decreases considerably. If this happens,

replace the batteries with new one as soon as possible.

– Exhausted batteries may leak. If the batteries have leaked,

dispose of them immediately. Avoid touching the leaked

material or letting it come into contact with clothing, etc.

Clean the battery compartment thoroughly before

installing new batteries.

– If you plan not to use the unit for a long period of time,

remove the batteries from the unit. Otherwise, the batteries

will wear out, possibly resulting in a leakage of battery

liquid that may damage the unit.

– Do not throw away batteries with general house waste.

Dispose of them correctly in accordance with your local

regulations.

22 Excessive sound pressure from earphones and headphones

can cause hearing loss.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit

itself is turned off by . In this state, this unit is designed

to consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

There is a chance that placing this unit too close to a CRT-

based (Braun tube) TV set might impair picture color.

Should this happen, move this unit away from the TV set.

1 En

English

NAMES OF PARTS AND THEIR FUNCTIONS ........2

Top panel/Front panel....................................................2

Front panel display.........................................................2

Remote control...............................................................3

CONNECTIONS ........................................................4

Connecting the speakers and antenna ..........................4

Connecting the power cable...........................................5

Other connections..........................................................5

About the standby state .................................................5

How to use the remote control .......................................5

ADJUSTING THE CLOCK (OPTION MENU) ...........6

LISTENING TO CD AND USB DEVICES .................7

Listening to a CD............................................................7

Listening to a USB device..............................................8

Using repeat/shuffle playback (remote control only)......8

LISTENING TO MUSIC FROM YOUR Bluetooth

DEVICE......................................................................9

Playing back from your Bluetooth device .......................9

Connecting an already-paired device via Bluetooth.....10

Disconnecting a Bluetooth connection.........................10

LISTENING TO FM STATIONS ..............................11

Selecting an FM station................................................11

Presetting FM stations (remote control only) ...............12

Selecting preset FM stations........................................13

LISTENING TO EXTERNAL SOURCES ................13

USEFUL FUNCTIONS ............................................14

Using the Option menu ................................................14

Using the sleep timer ...................................................15

Using the alarm function ..............................................15

Setting the alarm ..........................................................16

Operations while the alarm sound is playing................17

TROUBLESHOOTING ............................................18

NOTES ON DISCS AND USB DEVICES................21

SPECIFICATIONS...................................................22

CONTENTS

• Play back music from external devices such as your audio/data CDs, USB devices, or external devices via the AUX jack,

and listen to the radio.

•By the Bluetooth technology, you can enjoy clear sound without wire connections.

• Use your favorite music as an alarm. When the set time arrives, the music you select is played at the volume that you

specify, giving you the ideal start to your day.

• You can easily store and recall of your favorite radio stations, up to 30 FM stations.

• Bass, middle, and treble can be adjusted to your taste.

 About this manual

• If an operation can be performed using either the buttons on the unit itself or from the remote control, the explanation will

focus on operation using the remote control.

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

Features

Supplied accessories

FM antenna

(use a CR2025 type

Lithium battery)

Remote control Speaker cable

(1.5 m (4.9') x 2)

Power cable

Keep the USB cap out of

reach of children so as to

ensure that it is not

mistakenly swallowed.

USB cap

2 En

1 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (☞ P. 5).

2 SOURCE

Switch the audio source to be played.

Pressing this repeatedly will change the selection in the

following order.

CD USB

FM BT AUX

3 Audio control buttons

Use these to operate the CD/USB device.

4 (Eject button)

Eject the CD (cannot be operated while the option menu

(☞ P. 14) is displayed).

5 USB port

Connect your USB device (

☞

P. 5, 8).

When the USB device is not in use, put the USB cap in

place to protect the connector.

6 PRESET /

Use these buttons to select a radio station that you’ve

stored (☞ P. 12, 13).

7 (Headphone jack)

Connect headphones.

8 Front panel display

The clock and other information is displayed.

9 VOLUME knob

Adjust the volume.

0 Disc tray

Set a disc. ( ☞ P. 7).

1 Alarm time

Indicates the alarm time (☞ P. 16).

2 Repeat/shuffle indicator

Displays the playback mode (☞ P. 8).

3 Multi-function indicator

Displays various information, including the clock time,

information about the currently-playing track, and the

frequency of the radio station.

4 Remote control signal receiver

Make sure that this sensor is not obstructed (☞ P. 5).

5 Alarm indicator

Turns on if the alarm has been set (☞ P. 16).

6 Sleep indicator

Turns on if the sleep timer has been set (☞ P. 15).

NAMES OF PARTS AND THEIR FUNCTIONS

Top panel/Front panel

: Play/Pause

: Stop

/ : Skip, Search backward/forward (press and hold

down)

Front panel display

3 En

NAMES OF PARTS AND THEIR FUNCTIONS

English

 Replacing the battery in the remote control

While pushing the release tab in direction , slide out the

battery holder in direction .

1 Remote control signal transmitter

2 (Power)

Press to turn the unit on/off (standby).

There are two types of the standby state (☞ P. 5).

3 Source buttons

Switch the audio source to be played. If you press one of

these while the unit is in standby (except ECO standby),

the unit will automatically turn on.

4 OPTION

Display the option menu (☞ P. 14).

5 Operation buttons

FOLDER /: Switch the playback folder and select

items or edit numerical values when

playing music on data CDs or USB

devices.

ENTER: Confirm a selected item or value.

* Use these to operate the CD/USB device.

6 TUNING /

Tune the radio (☞ P. 11, 12).

7 PRESET /

Select a radio station that you stored (☞ P. 12, 13).

8 (Repeat)/ (Shuffle)

Play music on a CD or USB device in repeat/shuffle

mode (☞ P. 8).

9 ALARM

Switch the alarm on/off (☞ P. 17).

0 SNOOZE/SLEEP

Set the sleep timer or switch the alarm to snooze mode

(☞ P. 15, 17).

A DISPLAY

Switch the information shown in the front panel display

(☞ P. 7, 8, 11).

B MUTE

Mute or unmute the sound.

C VOLUME +/ –

Adjust the volume.

D MEMORY

Store a radio station (☞ P. 12).

Remote control

CR2025 type

Lithium battery

: Stop*

: Play/Pause*

/ : Skip, Search backward/forward (press and hold

down)*

4 En

Connect the speakers and antenna.

Do not connect this unit’s power cable until you’ve finished connecting all cables.

If the radio reception is poor, try changing the height or direction or placement of the antenna to find a location that has better

reception.

If you use a commercially available outdoor antenna instead of the supplied antenna, reception may be better.

CONNECTIONS

Connecting the speakers and antenna

Speakers

• You must peel off the insulation (covering) from the tip of the speaker cable to expose the conductor.

• Check the connections; make sure that left and right (L, R) and polarity (red: +, black: –) are connected correctly. If connections are

incorrect, the sound will be unnatural and the low frequencies may be insufficient. There might not be any sound at all if connections are

incorrect.

• Take care that the conductors of the speaker cable do not touch each other, and that the conductors do not touch any other metal part.

Such conditions can damage this unit or the speakers.

• Use only the supplied speakers. Using other speakers may result in unnatural sound.

• If you’re using this unit nearby a CRT display and you notice distorted color or noise in the display, move the speakers farther away from

the display.

FM antenna

Fix the end of the FM antenna to a wall.

Connect the FM

antenna plug to the

rear panel FM

antenna terminal with

the side illustrated on

the left.

Twist the bare wires

tightly so the individual

strands are not splayed.

Reset button

(☞ P. 18)

5 En

CONNECTIONS

English

 USB device

 External devices

This unit has the following two types of standby state. Select the mode in POWER SAVING settings menu (☞ P. 14).

* Default setting

Connecting the power cable

When you’ve completed all connections, connect the

supplied power cable to AC IN, and then connect the plug of

the cable to an AC outlet.

Other connections

Rear panel

To AC outlet

Connect your USB device to the USB port on the top panel.

For details on playable files, refer to “NOTES ON DISCS

AND USB DEVICES” (☞ P. 21).

The USB device is automatically charged when this unit is on or in

standby.

• Stop playback before disconnecting the USB device.

• Charging may not be possible depending on the USB device.

Using a commercially available 3.5 mm stereo mini-plug

cable, connect your external device to the AUX jack on the

rear panel of this unit.

About the standby state

Mode

Setting menu

(POWER

SAVING)

Clock display

Bluetooth

connection

Charging of USB

devices

Alarm setting

ECO standby

*

(power saving mode)

ECO No clock display Disable Disable Disable

Standby NORMAL Show Enable Enable Enable

How to use the remote control

Rear panel

Within 6 m (20')

Battery insulation sheet: Remove before using.

6 En

You’ll use the option menu (☞ P. 14) to set this unit’s date and time.

ADJUSTING THE CLOCK (OPTION MENU)

1 Press to turn the unit on.

2 Press OPTION.

The option menu will appear.

3 Press  / to select “CLOCK SET,” and then

press ENTER.

The display will indicate “CLOCK YEAR,” and the

numerical value to be set will blink.

4 Set the date and time.

Press ▲/▼ to edit each numerical value, and then press

ENTER to confirm the setting.

Set the items in the order of year month day

hour minute.

When clock setting has finished, the display will indicate

“Completed!”

The clock will be set to 0 second the moment you

complete the clock settings.

• While making these settings, you can press DISPLAY to

select the time format (12-hour / 24-hour).

• If you decide to cancel without changing the setting, press

OPTION before confirming the change.

The time settings will be reset if the unit remains unpowered for

about one hour.

26

Apr

Jan Feb Mar Apr May Jun

January February March April May June

Jul Aug Sep Oct Nov Dec

July August September October November December

2

43

15:30

CD

Display (24-hour) when the unit is on

Display (24-hour) when the unit is off (standby)

*

Clock display

1

* In ECO standby, the clock display will disappear.

7 En

English

 Skipping folders (remote control only)

 Display information (remote control only)

LISTENING TO CD AND USB DEVICES

The unit will operate as follows when playing back tracks/files on CD/USB devices.

• If the CD/USB device being played is stopped, the track that you listened will start playback from the beginning of the

track the next time you play.

• If you press while playback is stopped, tracks will play as follows the next time playback begins:

 Audio CD: Play from the first track of the CD.



Data CD*/USB device:

Play from the first track of the folder contains the track you listened to last time.

• This unit automatically turns off (standby) if no operation has been performed for 20 minutes after CD/USB device

playback is stopped.

* “Data CD” is a CD that contains MP3/WMA files.

For details on playable discs and files, refer to “NOTES ON DISCS AND USB DEVICES” (☞ P. 21).

Listening to a CD

1 Press the CD source button to switch the

audio source to CD.

If a CD is already set, playback will start.

2 Press the (eject button) to open the disc tray.

3 Set a CD into the disc tray.

Set the CD with the label side facing upward.

4 Press the (eject button) to close the disc

tray.

5 Press the to start playback.

Playback can be controlled with either the remote

control, or the top panel on this unit (☞ P. 2, 3).

Folders and files on a data CD are played in alphabetical order.

While a data CD is playing, you can use the remote control’s

FOLDER ▲/▼ buttons to select the folder.

The folder number (only for a data CD) or the song/file

number is shown for several seconds when starting playback

or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order.

- Elapsed song playback time

- Remaining song playback time (only for an audio CD)

- Song name*

- Album name*

- Artist name*

- File name (only for a data CD)

- Folder name (only for a data CD)

* Shown only if this data is included in the song.

3

2 4

5

1

LISTENING TO CD AND USB DEVICES

8 En

 Skipping folders (remote control only)

 Display information (remote control only)

The playback status is shown by the repeat/shuffle indicator in the front panel display.

Repeat playback Shuffle playback

Listening to a USB device

1 Press the USB source button to switch the

audio source to USB.

If a USB device is already connected, playback will start.

2 Connect a USB device to the USB port.

Playback starts automatically.

Playback can be controlled with either the remote control,

or the top panel on this unit (

☞

P. 2,

3

).

Folders and files will play in the order in which they were written.

Stop playback before disconnecting the USB device.

While a USB device is playing, you can use the remote

control’s FOLDER ▲/▼ buttons to select the folder.

The folder/file number is shown for several seconds when

starting playback or skipping tracks.

If you press

DISPLAY

on the remote control while a song is

playing or paused, the information shown on the front panel

display will be switched in the following order.

- Elapsed song playback time

- Song name*

- Album name*

- Artist name*

- File name

- Folder name

* Shown only if this data is included in the song.

Using repeat/shuffle playback (remote control only)

1

2

Press (repeat) repeatedly

to select one of the following

playback modes.

No display: Repeat mode off

: 1 track

: All tracks within the folder (data CD/USB device

only)

: All tracks

Press (shuffle) repeatedly

to select one of the following

playback modes.

No display: Shuffle mode off

: All tracks within the folder (data CD/USB device

only)

: All tracks

9 En

English

This unit provides Bluetooth functionality. You can enjoy wireless music playback from your Bluetooth device (mobile

phone, digital audio player, etc.). Please also refer to the owner’s manual of your Bluetooth device.

You’ll need to perform the pairing operation the first time you use your Bluetooth device with this unit, or if the pairing

settings have been deleted. Pairing is an operation that registers the Bluetooth device with this unit. Once pairing has been

completed, subsequent reconnection will be easy even after the Bluetooth connection is disconnected (☞ P. 10). If pairing is

not successful, refer to the item “Bluetooth” in “TROUBLESHOOTING” (☞ P. 20).

Yamaha does not guarantee all connections between this unit and Bluetooth device.

• This unit can be paired with up to 8 Bluetooth devices. When pairing with the 9th device has succeeded, pairing data for the device with the

oldest connection date will be deleted.

• While connecting to the Bluetooth device and perform the pairing with another device, the current Bluetooth connection will be canceled.

LISTENING TO MUSIC FROM YOUR

Bluetooth

DEVICE

Playing back from your Bluetooth device

1 Press the BLUETOOTH source button for

more than 2 seconds to enter pairing mode.

• Pairing mode lasts for 5 minutes.

• In pairing mode, the front panel display of this unit will

indicate “BT Pairing...”.

You can also enter pairing mode by holding down SOURCE on

this unit.

2 Perform Bluetooth pairing on the Bluetooth

device.

For details refer to the owner’s manual of the Bluetooth

device.

3 From the Bluetooth connection list of the

Bluetooth device, choose this unit (MCR-B020

Ya m a h a ) .

When pairing has been completed, the front panel display

of this unit will indicate “BT Pairing OK”.

If you are asked to enter a password, enter the numerals “0000”.

4 Connect this unit and the Bluetooth device via

Bluetooth.

5 Play back music from the Bluetooth device.

Take care that the volume setting of this unit is not too high. We

recommend that you adjust the volume on the Bluetooth device.

• If you connect via Bluetooth from the Bluetooth device while this

unit is in standby (except ECO standby), this unit will

automatically turn on.

• If you disconnect the Bluetooth connection from the Bluetooth

device while the audio source is set to Bluetooth, this unit will

automatically turn off (standby).

• If Bluetooth is selected as the audio source, this unit will

automatically turn off (standby) when 20 minutes have elapsed

without any Bluetooth connection nor any operation performed.

1

15:30



BT

Pairing OK

3

LISTENING TO MUSIC FROM YOUR Bluetooth DEVICE

10 En

Once pairing has been completed, connecting a Bluetooth will be easy the next time.

 Connecting from this unit

 Connecting from the Bluetooth device

If any of the following operations are performed while a Bluetooth connection is being used, the Bluetooth connection will be

disconnected.

• Switch the audio source other than Bluetooth.

• Turn the unit off.

• Turn off the Bluetooth setting of the Bluetooth device.

Connecting an already-paired device via Bluetooth

Press the BLUETOOTH source button to switch

the audio source to Bluetooth.

The Bluetooth indicator will blink in the front panel display;

this unit will search for the Bluetooth device that was most

recently connected via Bluetooth, and will then establish a

connection (You must first turn on the Bluetooth setting of

the Bluetooth device).

When the Bluetooth connection has been established, the

Bluetooth indicator will light, and the name of the Bluetooth

device will be displayed.

1 In the Bluetooth settings of the Bluetooth device, turn Bluetooth on.

2

From the

Bluetooth

connection list of the

Bluetooth

device, choose this unit (MCR-B020 Yamaha).

The Bluetooth connection will be established, and the front panel display of this unit will indicate the name of the

Bluetooth device.

Bluetooth

connections cannot be established from the

Bluetooth

device when this unit is in ECO standby (

☞

P. 5).

Disconnecting a Bluetooth connection

15:30



15:30



BT

_____

11 En

English

To listen to the FM station, connect the antenna as described in “Connecting the speakers and antenna” (☞ P. 4).

 Display information (remote control only)

If you press DISPLAY on the remote control, the information shown on the front panel display will be switched in the

following order.

LISTENING TO FM STATIONS

Selecting an FM station

1 Press the RADIO source button to switch the

audio source to FM.

2 Tune FM stations

Automatic tuning: Press and hold TUNING /.

Manual tuning: Press TUNING / repeatedly.

If you tune to a station manually while receiving FM, the sound

will be monaural.

Preset number and frequency

Reception status*

* Example of reception status indication.

TUNED/STEREO: A strong FM stereo broadcast is

being received.

TUNED/MONO: A monaural FM broadcast is being

received (even if the FM broadcast is

stereo, reception will be monaural if

the signal is weak).

Not TUNED: No broadcast is being received.

Displaying Radio Data System information

If you press DISPLAY on the remote control while Radio

Data System information is being received, the information

shown on the front panel display will be switched in the

following order.

- PS (Program Service)

- PTY (Program Type)

-RT (Radio Text)

-CT (Clock Time)

- Reception status

- Preset number and frequency

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text) information

uses a lot of bandwidth, so it may be less available compared to

other types of information.

1

2

LISTENING TO FM STATIONS

12 En

Use the preset function to store your favorite 30 stations.

First, press the RADIO source button to switch the audio source to FM.

 Auto preset

This method tunes automatically, and automatically presets only the stations that have good reception.

 Manual preset

 Deleting a stored preset (Option menu)

Presetting FM stations (remote control only)

1 Press and hold down MEMORY.

“AUTO PRESET” will appear and “Press MEMORY”

will blink.

2 Press MEMORY.

Auto preset will begin.

When presetting has finished, the display will indicate

“Completed!”.

When you perform auto preset, all stored stations are cleared

and the new stations are stored.

If you want to stop auto preset before it is completed, press .

1 Press TUNING / to tune a station that

you want to preset.

2 Press MEMORY.

The display will indicate “PRESET MEMORY,” and the

preset number will blink.

3 Press PRESET / to select the preset

number that you want to store.

• The lowest preset number that has not been stored will be

selected first.

• If you want to cancel the presetting, press .

• If you select a preset number in which a station has already

been stored, it will be overwritten by the new station.

4 Press MEMORY.

When presetting has finished, the display will indicate

“Completed!”.

1 Press OPTION.

The option menu will appear.

2 Press  / to select PRESET DELETE, and

then press ENTER.

3 Press  / to select the preset number that

you want to delete.

If you want to cancel the deleting, press OPTION.

4 Press ENTER to complete the operation.

When deleting has finished, the display will indicate

“Deleted!”.

5 Press OPTION to exit the option menu.

AUTO PRESET



Press MEMORY

1 2

PRESETMEMORY

FM0187.50MHz

3

1

42

1 5

3

4

2

13 En

LISTENING TO FM STATIONS

English

Selecting preset FM stations

1 Press the RADIO source button to switch the

audio source to FM.

2 Press PRESET / to select the FM station

that you want to hear.

You can only select presets that have been stored.

LISTENING TO EXTERNAL SOURCES

1 Using a commercially available 3.5 mm stereo

mini-plug cable, connect your external device

to the AUX jack on the rear panel of this unit.

• Turn the unit off before connecting the audio cable.

• Turn down the volume of the unit and your external audio

device before connection.

2 Press to turn the unit on.

3 Press the AUX source button to switch the

audio source to AUX.

4 Start playback on the connected external

audio device.

1

2

1

2

Rear panel

3

14 En

When you press

OPTION

, the option menu will appear in the front panel display, allowing you to make the following settings.

(eject button) cannot be operated while the option menu is displayed.

*1

Default setting

 Procedure for settings

USEFUL FUNCTIONS

Using the Option menu

Option menu Setting or range See page

PRESET DELETE Deletes a stored preset (shown only if the audio source is FM).

12

DIMMER

Adjusts the brightness of the front panel display (1

*1

: bright, 2: medium, 3: dim).

–

EQ LOW

Adjusts the tonal character (low frequencies) (–10 - 0

*1

- +10 dB).

–

EQ MID

Adjusts the tonal character (mid frequencies) (–10 - 0

*1

- +10 dB).

–

EQ HIGH

Adjusts the tonal character (high frequencies) (–10 - 0

*1

- +10 dB).

–

BALANCE

Adjusts the volume balance of the left and right speakers (L+10 - CENTER

*1

- R+10).

–

POWER SAVING

Switches the standby state, NORMAL or ECO

*1

(power saving mode)

5

AUTO PWR

STDBY

You can specify the time after which the unit will turn off (standby) automatically.

If no operation occurs for the duration you specify, the unit will turn off (standby) automatically

(

TIME 12H

: 12 hours,

TIME 8H

*1

: 8 hours,

TIME 4H

: 4 hours,

TIME 2H

: 2 hours,

OFF

: the unit

will not turn off (standby)).

–

CLOCK SET Sets the date and time.

6

ALARM SET Sets the alarm.

16

BLUETOOTH

Connects this unit and your device via Bluetooth (ON

*1

: enable, OFF: disable).

9

1 Press OPTION.

The option menu will appear.

2 Press  / to select the menu item that you

want to set, and then press ENTER.

3 Press  / to edit the setting, and then press

ENTER to confirm the setting.

If you want to continue making other settings, repeat the

procedure from step .

4 Press OPTION to exit the option menu.

If you decide to cancel without changing the setting, press

OPTION before confirming the change.

1

3

4

2

15 En

USEFUL FUNCTIONS

English

When the specified time has elapsed, the unit will turn off automatically.

The internal sound (melody) and then the selected audio source are played at the time set for the alarm.

If the selected audio source cannot be played back at the time set for the alarm, the internal sound is played back.

 Various audio sources

You can choose from audio CD, data CD, USB device, or FM. The following playback methods can also be selected

depending on the audio source:

You can not choose Bluetooth and AUX as the audio source.

Snooze

The snooze function can be enabled to replay the alarm after 5 minutes (☞ P. 17).

Using the sleep timer

Press SNOOZE/SLEEP repeatedly to specify the

time after which the unit will turn off.

You can specify 30, 60, 90, 120 or OFF.

When you select a time, the sleep timer is turned on, and the

sleep indicator ( ) is shown in the front panel display.

If you press SNOOZE/SLEEP while the sleep timer is activated,

the sleep timer setting will be canceled.

Using the alarm function

Source

Playback

method

Function

Audio CD

Selected track The selected track is played repeatedly.

Resume The track you listened to last time is played back.

Data CD/USB device

Folder The selected folder is played repeatedly.

Resume The track you listened to last time is played back.

FM

Preset station The selected preset station is played.

Resume The FM station you listened to last time is played back.

USEFUL FUNCTIONS

16 En

 Setting the alarm time and alarm source (Option menu)

The alarm will not function when the unit is in ECO standby. To use the alarm function, set the Option menu item POWER SAVING to

NORMAL (☞ P. 14).

Setting the alarm

1 Press OPTION.

The option menu will appear.

2 Press  / to select “ALARM SET”, and then press ENTER.

The alarm indicator ( ) and numerical value you’re setting will blink.

3 Set the alarm.

Set items 1-3 described below.

Press

 / to select a numerical value, and press ENTER to confirm it.

4 Complete the settings.

When you set the VOLUME for item 3, the display will indicate

“Completed!” and your settings will be confirmed.

The alarm will be turned on and the alarm indicator ( ) will light.

If you press OPTION or turn the unit off while making alarm settings, the settings will

be cancelled.

4

9:12



Completed!

Alarm time

Alarm indicator

3

1

2

*1

If you choose RESUME when specifying the track/folder/preset number, the last-

played track/folder/station will be played (resume playback)

Items Setting or range

1

ALARM TIME

Make settings in the order of hours minutes.

2

ALARM SOURCE

CD: Play back music from a CD.

Specify the track number (data CD: folder

number) (RESUME

*1

, 1-99).

USB: Play back music from a USB device.

Specify the folder number (RESUME

*1

, 1-999).

FM: Play a FM station.

Specify the preset number (RESUME

*1

, 1-30).

3

ALARM VOLUME

Specifies the volume (5-60) of the alarm.

17 En

USEFUL FUNCTIONS

English

 Switching the alarm on/off

When the set time arrives, the set alarm sound will play. During playback, the following operations are available.

 To pause the alarm (Snooze)

 To turn the alarm off

Press ALARM to turn the alarm on/off.

When the alarm is on, the alarm indicator ( ) will light,

and the alarm time will be shown.

If you press ALARM again, the alarm indicator ( )

and the alarm will turn off.

If the Option menu item POWER SAVING is set to ECO,

the alarm will not function

(☞ P. 1 4).

Operations while the alarm sound is playing

Press SNOOZE/SLEEP.

Snooze will stop the alarm and play it again 5 minutes later.

• If you press SNOOZE/SLEEP while the alarm is activated, the

alarm sound will stop for about 5 minutes.

• Buttons on the unit other than the will also function as the

snooze button.

Press ALARM or .

• You can also stop the alarm by holding down SNOOZE/SLEEP.

• If you don’t stop the alarm, it will stop automatically after 60

minutes and the unit will turn off.

• The alarm setting will be saved even if the alarm is turned off.

If the alarm is turned on again by pressing ALARM, the alarm

will sound with the previous alarm settings.

18 En

If there is a problem with the unit, check the following list first. If you cannot resolve the problem with the suggested

solutions or if the problem is not listed below, turn off and unplug the unit, and consult the nearest authorized Yamaha dealer

or service center.

TROUBLESHOOTING

General

Problem Cause Solution

The speakers make no sound. The volume might be set to the minimum level,

or muted.

Adjust the volume level.

The source may be incorrect. Select the correct source.

The speakers may not be connected securely. Check the connections (☞ P. 4 ).

Headphones are connected. Remove the headphones.

The volume of a connected external device is not

loud enough.

Raise the volume of the external device.

Sound suddenly turns off. The sleep timer may be set (☞ P. 15). Turn the unit on and play the source again.

The auto power standby function may have

operated.

When the time specified for AUTO PWR STDBY in the

option menu has elapsed (☞ P. 14) or when 20 minutes

have elapsed without any operation being performed after

stopping USB device or CD playback, the unit will turn off

automatically.

Sound is cracked/distorted or

there is abnormal noise.

Input source volume is excessive, or volume of

this unit is excessive (especially Bass).

Adjust volume with VOLUME, or use the option menu

(☞ P. 14) to adjust the bass range. If an external device is

playing back, lower the volume of the external device.

The unit does not operate

properly.

The unit may have received a strong electrical

shock such as lightning or excessive static

electricity, or power supply may have dropped.

Press the reset button on the rear panel of the unit (☞ P. 4 )

using a fine-tipped stick and restart the unit.

The unit turns on but

immediately shuts off.

A digital or high-frequency

equipment produces noises.

The unit may be placed too close to the digital or

high-frequency equipment.

Place the unit farther away from the equipment.

The clock setting has been

cleared.

The unit remained unpowered for about one hour. Plug the power cable into the wall outlet firmly, and set the

clock again (☞ P. 6 ).

Alarm does not sound. The unit is set to ECO standby. In the option menu, set POWER SAVING to NORMAL

(☞ P. 1 4).

The front panel display indicates

“ALARM not work” and can’t

set the alarm.

The unit turns off unexpectedly. The auto power standby function may have

operated.

When the time specified for AUTO PWR STDBY in the

option menu has elapsed (☞ P. 14) or when 20 minutes

have elapsed without any operation being performed after

stopping USB device or CD playback, the unit will turn off

automatically.

Remote control

Problem Cause Solution

The remote control does not work

properly.

The remote control may be operated outside its

operation range.

For information on the remote control operation range,

refer to “How to use the remote control” (☞ P. 5 ).

The remote control signal receiver on the unit

(☞ P. 2) may be exposed to direct sunlight or

lighting (inverted fluorescent lamps).

Change the lighting or orientation of the unit.

The battery may be worn out. Replace the battery with a new one (☞ P. 3 ).

There are obstacles between the remote control

signal receiver on the unit (☞ P. 2) and the

remote control.

Remove the obstacles.

Sayfa yükleniyor ...

Yamaha MCR-B020 El kitabı

Yamaha MCR-B020 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler