NEC PlasmaSync® 60XC10 El kitabı

English

Important Safety Instructions ..............................................................................................................English-1

Important Information ...........................................................................................................................English-2

Safety Precautions and Maintenance ...................................................................................................English-3

Recommended Use ....................................................................................................................................English-4

Installation

Optional Stands/Mounts ..........................................................................................................English-6

Mounting Location ....................................................................................................................English-6

Mounting on Ceiling ..................................................................................................................English-7

Maintenance, Orientation, Cable Management ..................................................................English-7

Using the Remote ......................................................................................................................English-8

Part Names and Functions

Control Panel ..............................................................................................................................English-9

Terminal Panel ............................................................................................................................English-10

Remote Control ..........................................................................................................................English-11

Power, Display, Digital Zoom, Pointer, Main Power Switch Cover .....................................English-12

Remote Control ID .....................................................................................................................English-13

On-Screen Display (OSD)

Using the OSD .............................................................................................................................English-14

OSD ................................................................................................................................................English-15

Troubleshooting.........................................................................................................................................English-18

Speciﬁ cations

42XC10..........................................................................................................................................English-19

50XC10 .........................................................................................................................................English-20

60XC10 .........................................................................................................................................English-21

Supported Resolutions

42XC10..........................................................................................................................................English-22

50XC10 .........................................................................................................................................English-24

60XC10 .........................................................................................................................................English-26

Pin Assignment ..........................................................................................................................................English-28

Package Contents

Table of Contents

Plasma Monitor

Remote control and AA Batteries

Power cord

Users Manual (CD-ROM)

Start Up Guide (Paper / CD-ROM)

Main Power Switch cover and screw

Cable clamps

•

English-1

Read Before Operating Equipment.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in

accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and third grounding prong  e wide

blade or third prong are provided for your safety. If the

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories speci ed by the

manufacturer

12. Use only with the cart, stand, tripod, bracket, or

table speci ed by the manufacturer, or sold with the

apparatus. When a cart is used, use caution when

moving the cart or apparatus combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as when the power-supply

cord or plug is damaged, liquid has been spilled or

objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate

normally, or has been dropped

Additional Safety Information

15.  is product may contain lead. Disposal of these

materials may be regulated due to environmental

considerations.

For disposal or recycling information, please contact

your local authorities or the Electronic Industries

Alliance: www.eiae org.

16. Damage Requiring Service - e appliance should be

serviced by quali ed service personnel when:

A.  e power supply cord or the plug has been damaged;

or

B. Objects have fallen, or liquid has been spilled into

the appliance;

or

C.  e appliance has been exposed to rain;

or

D.  e appliance does not appear to operate normally or

exhibits a marked change in performance;

or

E.  e appliance has been dropped, or the enclosure

damaged.

17. Tilt/Stability - All monitors must comply with

recommended international global safety standards for

tilt and stability properties of its cabinet design.

Do not compromise these design standards by applying

excessive pull force to the front, or top, of the cabinet

which could ultimately overturn the product.

Also, do not endanger yourself, or children, by placing

electronic equipment/toys on the top of the cabinet.

Such items could unsuspectingly fall from the top of the

set and cause product damage and/or personal injury.

18. Wall/Ceiling Mounting -  e appliance should be

mounted to a wall/ceiling only as recommended by the

manufacturer.

19. Power Lines - An outdoor antenna should be located

away from power lines.

20. Outdoor Antenna Grounding - If an outside antenna is

connected to the receiver, be sure the antenna system

is grounded so as to provide some protection against

voltage surges and built up static charges.

Section 810 of the National Electric code. ANSI/NFPA

No.70-1984, provides information with respect to

proper grounding of the mats and supporting structure,

grounding of the lead-in wire to an antenna-discharge

unit, size of grounding connectors, location of antenna

discharge unit, connection to grounding electrodes and

requirements for the grounding electrode.

21. Objects and Liquid Entry - Care should be taken so that

objects do not fall and liquids are not spilled into the

enclosure through openings.

Apparatus shall not be exposed to dripping or splashing

and no objects  lled with liquids, such as vases, shall be

placed on apparatus

WA R N I N G

To reduce the risk of  re or electric shock, do not expose

this apparatus to rain or moisture.

Important Safety Instructions

English-2

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THIS

UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS

CAN BE FULLY INSERTED.

REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALL

SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORD

FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

 is symbol warns user that uninsulated voltage within the unit may have su cient magnitude to cause electric shock.

 erefore, it is dangerous to make any kind of contact with any part inside this unit.

 is symbol alerts the user that important literature concerning the operation and maintenance of this unit has been

included.  erefore, it should be read carefully in order to avoid any problems.

Important Information

Canadian Department of

Communications Compliance Statement

DOC:  is Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

FCC Information

1. Use the attached speci ed cables with the P426Y3(P42XC10),

P506Y4(P50XC10) or P606Y5(P60XC10) color monitor so as not to

interfere with radio and television reception.

(1) Please use the supplied power cord or equivalent to

ensure FCC compliance.

(2) Please use shielded video signal cable,

15-pin mini D-SUB to 15-pin mini D-SUB

with ferrite cores on both ends (not included).

2.  is equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.  ese

limits are designed to provide reasonable protection against harmful

interference in a residential installation.  is equipment generates, uses,

and can radiate radio frequency energy, and, if not installed and used

in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged

to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the distance between the equipment and

receiver.

Connect the equipment into an outlet on a circuit

di erent from that to which the receiver is connected.

Consult your dealer or an experienced radio/TV technician for help.

If necessary, the user should contact the dealer or an experienced radio/

television technician for additional suggestions.  e user may  nd the

following booklet, prepared by the Federal Communications Commission,

helpful: “How to Identify and Resolve Radio-TV Interference Problems.”  is

booklet is available from the U.S. Government Printing O ce, Washington,

D.C., 20402, Stock No. 004-000-00345-4.

WARNING

 is product equipped with a three-wire grounding (earthed) plug - a plug

that has a third (grounding) pin.  is plug only  ts a grounding-type power

outlet. If you are unable to insert the plug into an outlet, contact a licensed

electrician to replace the outlet with a properly grounded one. Do not defeat

the safety purpose of the grounding plug.

•

CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not

supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the AC

voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.

Plug Type North America

European

Continental

U.K. Chinese Japanese

Plug Shape

Country

Voltage

U.S.A./Canada U.K. China JapanEU (except U.K.)

120* 230 220 100230

*When operating the PlasmaSync monitor with its AC 125-240V power supply, use a power supply cord that matches the power

supply voltage of the AC power outlet being used.

English-3

Safety Precautions

and Maintenance

FOR OPTIMUM PERFORMANCE, PLEASE NOTE

THE FOLLOWING WHEN SETTING UP AND

USING THE MONITOR:

 e plasma display's panel is made up of  ne picture

elements (cells), of which more than 99.99 percent are active

cells. Some cells may not produce light or remain constantly

lit. For safe operation and to avoid damaging the unit, read

carefully and observe the following instructions.

DO NOT OPEN THE MONITOR.  ere are no user-

serviceable parts inside and opening or removing covers

may expose you to dangerous shock hazards or other

risks.  e manufacturer is not liable for any bodily harm

or damage caused if unquali ed persons attempt service

or open the back cover. Refer all servicing to quali ed

service personnel.

Do not spill any liquids into the cabinet or use your

monitor near water.

Do not insert objects of any kind into the cabinet slots,

as they may touch dangerous voltage points, which can

be harmful or fatal or may cause electric shock,  re or

equipment failure.

Do not bend, crimp or otherwise damage the power cord.

Do not place any heavy objects on the power cord.

Damage to the cord may cause shock or  re.

Do not place this product on a sloping or unstable cart,

stand or table, as the monitor may fall, causing serious

damage to the monitor.

Do not use in a moving vehicle, as the unit could drop or

topple over and cause injuries.

 e power cable connector is the primary means of

detaching the system from the power supply.  e

monitor should be installed close to a power outlet that

is easily accessible.

 is equipment shall be connected to a MAIN outlet

with a protective earth-ground connection. Do not place

any objects onto the monitor and do not use the monitor

outdoors.

Do not use this unit’s polarized plug with an extension

cord or with outlets unless the prongs can be inserted

fully.

 e power supply cord you use must have been approved

by and comply with the safety standards of your

country. (Type H05VV-F 3G 1mm

2

should be used in

Europe)

In UK, use a BS-approved power cord with molded plug

having a black (13A) fuse installed for use with this

monitor.

Use only with 100 V to 240 V 50 Hz/60 Hz AC power

supply. Continued operation at line voltages greater than

100 V to 240 V AC will shorten the life of the unit, and

might even cause a  re hazard.

•

Unplug the power cord during electrical storms or when

the unit will not be in use for a long period.

Do not use monitor in high temperature, humid, dusty,

or oily areas.

Do not cover vent on monitor.

Clean plasma ventilation areas using a vacuum cleaner

with a so brush nozzle attachment.

To ensure proper ventilation, cleaning the ventilation

areas must be carried out monthly. More frequent

cleaning may be necessary depending on the

environment in which the plasma monitor is installed.

Allow adequate ventilation around the monitor so that

heat can properly dissipate. Do not block ventilated

openings or place the monitor near a radiator or other

heat sources. Do not put anything on top of monitor.

Handle with care when transporting. Save packaging for

transporting.

As is the case with any phosphor-based display (like a

CRT monitor, for example) light output will gradually

decrease over the life of a Plasma Display Panel.

To avoid sulfurization it is strongly recommended not to

place the unit in a dressing room in a public bath or hot

spring bath.

CAUTION

Immediately unplug your monitor from the wall outlet and

refer servicing to quali ed service personnel under the

following conditions:

When the power supply cord or plug is damaged.

If liquid has been spilled on, or objects have fallen into

the monitor.

If the monitor has been exposed to rain or water.

If the monitor has been dropped or the cabinet

damaged.

If the monitor does not operate normally by following

operating instructions.

•

Safety Precautions and Maintenance

English-4

Recommended Use

CAUTION

CORRECT PLACEMENT AND ADJUSTMENT OF

THE MONITOR CAN REDUCE EYE, SHOULDER AND

NECK FATIGUE. CHECK THE FOLLOWING WHEN

POSITIONING THE MONITOR:

For optimum performance, allow 20 minutes for warm-

up.

Rest your eyes periodically by focusing on an object at

least 5 feet away. Blink o en.

Position the monitor at a 90 degree angle to windows

and other light sources to minimize glare and

re ections.

Clean the monitor surface with a lint-free, nonabrasive

cloth. Avoid using any cleaning solution or glass

cleaner.

Adjust the monitor’s brightness and contrast controls to

enhance readability.

Get regular eye checkups.

Ergonomics

To realize the maximum ergonomic bene ts, we recommend

the following:

Use the preset Size and Position controls with standard

signals.

Use the preset Color Setting.

Do not use primary color blue on a dark background, as

it is di cult to see and may produce eye fatigue due to

insu cient contrast.

 is equipment is not for use at video display work

station according to Bildscharb V.

For more detailed information on setting up a healthy work

environment, refer to the following document:

American National Standard for Human Factors

Engineering of Visual Display Terminal Workstations

ANSI-HFS Standard No. 100-1988

Published by:

 e Human Factors and Ergonomics Society

P.O. Box 1369, Santa Monica, California 90406.

•

Cleaning the Panel

When the panel becomes dusty or dirty, wipe gently

with so cloth.

Do not rub the panel with coarse material.

Do not apply pressure to the surface.

Do not use OA cleaner. OA cleaner will cause

deterioration or discolor the surface.

Cleaning the Cabinet

Unplug the power supply.

Gently wipe the cabinet with a so cloth.

To clean the cabinet, dampen the cloth with a neutral

detergent and water, wipe the cabinet and follow with a

dry cloth.

NOTE:  e surface of the cabinet is composed of many

types of plastic.

DO NOT clean with benzene thinner, alkaline

detergent, alcoholic system detergent, glass cleaner,

wax, polish cleaner, soap powder, or insecticide.

Rubber or vinyl should not be in contact with

the cabinet for an extended period of time.  ese

types of  uids and materials can cause the paint to

deteriorate, crack or peel.

CLEANING THE VENT HOLES

Clean plasma ventilation areas using a vacuum cleaner

with a so brush nozzle attachment.

To ensure proper ventilation, cleaning the ventilation

areas must be carried out monthly. More frequent

cleaning may be necessary depending on the

environment in which the plasma monitor is installed.

•

English-5

Recommended Use - continued

To avoid or minimize image

retention:

Like all phosphor-based display devices and all other gas

plasma displays, plasma monitors can be susceptible to image

retention under certain circumstances. Certain operating

conditions, such as the continuous display of a static

image over a prolonged period of time, can result in image

retention if proper precautions are not taken. To protect

your investment in this plasma monitor, please adhere to the

following guidelines and recommendations for minimizing

the occurrence of image retention:

Always enable and use your computer’s screen saver

function during use with a computer input source.

Display a moving image whenever possible.

Change the position of the menu display from time to

time.

Always power down the monitor when you are  nished

using it.

To reduce the likelihood of

image retention from long-term

use:

Lower the Brightness and Contrast levels as much as

possible without impairing image readability.

Display an image with many colors and color gradations

(i.e. photographic or photo-realistic images).

Create image content with minimal contrast between

light and dark areas. Use complementary or pastel colors

whenever possible.

Avoid displaying images with few colors and distinct,

sharply de ned borders between colors.

Plasma monitor driving sound

 e panel of the Plasma monitor is composed of

extremely  ne pixels and these pixels emit light

according to received video signals.  is principle may

cause you to hear a buzz or electrical hum coming from

the Plasma monitor. Also note that the rotation speed

of the cooling fan motor increases when the ambient

temperature of the Plasma monitor becomes high. You

may hear the sound of the motor at that time.

NOTE:  e following items are not covered by the

warranty.

• Image retention

• Panel generated sound. Examples: Fan motor

and electrical noises circuit humming /glass panel

buzzing.

•

OPERATING ENVIRONMENT

Operating environment temperature and humidity: 0 °C to

+40 °C (+32 °F to +104 °F); less than 80%RH (cooling vents

not blocked) Do not install this unit in a poorly ventilated

area, or in locations exposed to high humidity or direct

sunlight (or strong arti cial light)

WARNING

Not for use in a computer room as de ned in the Standard

for the Protection of Electronic Computer/Data Processing

Equipment ANSI/NFPA 75.

NOTE: Please use shielded video signal cable, 15-pin mini

D-SUB to 15-pin mini D-SUB with ferrite cores on

both ends (not included).

English-6

Using Optional Stand/Mounts

An optional stand or mounting apparatus can be installed

either while the unit is in the upright position or while the

unit is face-down.

To install the stand while in the upright position, lower the

monitor onto to the feet as shown (Figure 1). Use the handles

to support the display while lowering the support holes

underneath the display onto the feet.

If stand or mounting apparatus is to be installed while the

unit is face-down (Figure 2), be sure to lay the protective

sheet (the foam sheet that the unit was wrapped in)

underneath the unit on order to prevent damage to the

screen.

 is unit must be used with a stand or some type of

mounting apparatus.  is unit is not designed for use

without additional support.

For correct Installation and Mounting it is

recommended to use a trained, authorized dealer.

Failure to follow correct mounting procedures could

result in dame to the unit or to the installer.

Product warranty does not cover damage caused by

improper installation.

CAUTION:

To install, follow those instructions included with the

stand or mounting apparatus. Use only those devices

recommended by the manufacturer.

Make sure to install stand or mounting apparatus to the

unit while on a surface that is strong and stable enough

to support the weight of the unit, such as a  oor or

sturdy table.

Use the speci ed clasps for installation.

Take necessary steps to prevent the unit from tipping or

falling.

Mounting Location

 e ceiling and wall must be strong enough to support the

monitor and mounting accessories.

DO NOT install in locations where a door or gate can hit

the unit.

DO NOT install in areas where the unit will be subjected

to strong vibrations and dust.

DO NOT install near where the main power supply

enters the building.

DO NOT install in where people can easily grab and

hang onto the unit or the mounting apparatus.

When mounting in an enclosure or in a recessed area, as

in a wall, leave at least 2 inches (50mm) of space between

the monitor and the wall for proper ventilation (Figure 3).

•

Allow adequate ventilation or provide air conditioning

around the monitor, so that heat can properly dissipate

away from the unit and mounting apparatus.

•

50mm (2")

Installation

Figure 3

Figure 1

Figure 2

Tab le

Protective Sheet

English-7

Mounting on Ceiling

Ensure that the ceiling is sturdy enough to support the

weight of the unit and the mounting apparatus over

time, against earthquakes, unexpected vibrations, and

other external forces.

Be sure the unit is mounted to a solid structure within

the ceiling, such as a support beam. Secure the monitor

using bolts, spring lock washers, washer and nut.

DO NOT mount to areas that have no supporting

internal structure. DO NOT use wood screws or anchor

screws for mounting. DO NOT mount the unit to trim

or to hanging  xtures.

Maintenance

Periodically check for loose screws, gaps, distortions,

or other problems that may occur with the mounting

apparatus. If a problem is detected, please refer to

quali ed personnel for service.

Regularly check the mounting location for signs of

damage or weakness that may occur over time.

Please note the following when

mounting on wall or ceiling.

When using mounting accessories other than those that

are NEC approved, they must comply with the VESA-

compatible (FDMlv1) mounting method.

NEC strongly recommends

using size M8 screws

(16mm + thickness of

bracket in length). If using

screws longer than 16mm,

check the depth of the

hole.(Recommended Fasten

Force: 1125 - 1375N•cm)

NEC recommends mounting

interfaces that comply with

UL1678 standard in North

America.

Orientation

DO NOT use this monitor in the

portrait position. Doing so may cause

failure and void the warranty.

•

Cable Management

To conveniently manage cables, use the cable clamps

provided to bundle the power cord together with the signal

and audio cables at the back of the display.

To attach cable clamps:

1. Attach the cable clamps to the display. Insert the anchor

of the clamp into the hole on the back of the display.

 ere are 4 cable clamps and 4 clamp holes on the unit.

2. A er the cable clamp is positioned on the display, wrap

the end around the cables. Place the end of the clamp

into the slot near the anchor. Pull until cables are snug.

Clamps are designed to stay in place. Once in position,

they will be di cult to remove.

3. Cables can be routed to the right or le of the clamp.

Use the beaded bands to secure the cables together along

their length. Make sure the cables are fully supported.

To detach clamps:

Using pliers, twist the clamp 90 degrees and pull

outward. It is possible that the clamp can weaken over

time and removing it may cause damage to the clamp.

Installation - continued

Holes for Clamp

anchors

Anchor

Slot

Closed Clamp

16mm

Screw length should equal

depth of hole (16mm) + the

thickness of mounting bracket.

Unit

Mounting

Bracket

Screw

Thickness

of Bracket

English-8

Using the Remote:

Install the remote control batteries.

 e remote control is powered by AA batteries. To install or

replace batteries:

A. Press and slide to open the cover.

B. Align the batteries according to the (+)

and (–) indications inside the case.

C. Replace the cover.

CAUTION: Incorrect usage of batteries can result in leaks or

bursting. NEC recommends the following battery use:

Place “AA” size batteries matching the (+) and (-) signs

on each battery to the (+) and (-) signs of the battery

compartment.

Do not mix battery brands.

Do not combine new and old batteries, or mix brands.

 is can shorten battery life or cause liquid leakage of

batteries.

Remove dead batteries immediately to prevent battery

acid from leaking into the battery compartment.

Do not touch exposed battery acid, it may injure skin.

Do not drop or mishandle the remote.

Do not get the remote control wet. If the remote does get

wet, wipe dry immediately.

Avoid excessive heat and humidity.

Do not dispose of batteries in  re.

Please follow government regulations or public

environmental rules that apply in your country/area

when disposing of used batteries.

When replacing, use only conventional non-

rechargeable alkaline or manganese batteries.

 ere is a risk of explosion if batteries are replaced

incorrectly.

•

Operating Range for the Remote Control

Point the top of the remote control toward the monitor’s

remote sensor while pressing buttons.  e remote control

can be used from the front of the monitor at a maximum

distance of 7 m/23  . from the front of the Plasma monitor’s

remote control sensor.  e maximum horizontal and vertical

angle for use of the remote is 30 degree within a distance of

3.5 m/11.5  .

CAUTION

 e remote control may not function when direct sunlight

or strong illumination strikes the remote control sensor of

the Plasma monitor, or when there is an object in the path of

the sensor.

Handling the Remote Control

Do not open the remote control other than to install

batteries. Do not allow water or other liquid to splash onto

the remote control. If the remote control gets wet, wipe it dry

immediately.

Avoid exposure to heat and steam.

NOTE: If you do not intend to use the Remote Control for a

long period of time, remove the batteries.

Installation - continued

30

English-9

Part Names and Functions

Control Panel

1) POWER

Switches the power on/standby.

2) MUTE

Switches the audio mute ON/OFF.

3) INPUT

Switches between input sources.

Acts as SET button within the OSD menu.

4) PLUS (+)

Increases the setting adjustment within OSD menu.

5) MINUS (-)

Decreases the setting adjustment within OSD menu.

6) UP ( )

Increases the volume level when the OSD is o .

Moves area up to select which setting to is to be adjusted

within OSD menu.

7) DOWN ( )

Decreases the volume level when the OSD is o .

Moves down to select which setting is to be adjusted within

OSD menu.

8) EXIT

Activates the OSD menu when the OSD menu is o .

Exits from the current menu being displayed to the

previous menu within the OSD.

9) Remote control sensor and Power indicator

Receives the signal when using the wireless remote control.

Glows green when the monitor is active. Glows red when

the monitor is in Standby mode. Glows Amber when the

monitor is in POWER SAVE mode.

A red blinking Power indicator means that the monitor has

detected a failure. Contact quali ed personnel in case of

failure.

10) Main Power Switch

Seesaw switch to turn the main power on/o .

Mode Status indicator light

Power On Green

Standby Red

Power save Amber

Diagnosis

(Detecting failure)

Red blinking

1

2

3

45

6

7

8

OFFON

10

9

NOTE:

The POWER button does not completely turn off the

display. Use the Main Power Switch to completely turn off

the display.

English-10

EXTERNAL CONTROL

OUT

2

IN

S-VIDEO IN

DVI AUDIO3

R

L

(MONO)

R

L

(MONO)

R

L

(MONO)

AUDIO2 AUDIO1VGA

Y Cr/Pr Cb/Pb

DVD/HD1

DVD/HD2

IN

VIDEO AC IN

RL

SPEAKER (S)

1

3 4 5 6 7 8 10

9

12

11

13 14

DVD/HD3

Part Names and Functions

1) EXTERNAL CONTROL OUT (D-Sub 9 pin)

Connect RS-232C output to a second monitor.

2) EXTERNAL CONTROL (D-Sub 9 pin)

Connect RS-232C input to external equipment such as a

PC in order to control RS-232C functions.

3) DVD/HD3 (HDMI)

Input digital HDMI signals.

4) DVI

Input digital RGB signals from a computer or HDTV

device having a digital RGB output.

5) AUDIO3

Input the audio signal from external equipment such as a

computer, VCR or DVD player.

6) VGA (Mini D-Sub 15 pin)

Analog computer input.

7) AUDIO2

Input the audio signal from external equipment such as a

computer, VCR or DVD player.

8) DVD/HD1

Connect equipment such as a DVD player, HDTV device,

or set-top box.

9) DVD/HD2

Connect equipment such as a DVD player, HDTV device

or set-top.

10) AUDIO1

Input the audio signal from external equipment such as a

computer, VCR or DVD player.

11) S-VIDEO in

Input S-video.

12) VIDEO1

Composite video input.

13) EXTERNAL SPEAKER (L and R) connector

Connects to optional speakers. Output the audio signal

from AUDIO 1, 2, and 3 to external speakers.

NOTE: Speaker Terminal is for 8W + 8W (8 ohm).

14) AC IN

Connects with the supplied power cord.

Information:

For SCART connections there are 2 ways to connect:

SCART1: Connect R/G/B to the DVD/HD1 terminals and

composite sync. to the VIDEO1 terminal.

SCART2: Connect R/G/B + composite sync. to the VGA

terminal.

Terminal Panel

English-11

Part Names and Functions - continued

1) POWER ON/STANDBY

Switches the power on/standby.

*If the Power Indicator on the display is not glowing,

then no controls will work.

2) VIDEO

Switches the input signal to the VIDEO source.

3) RGB

Switches the input signal to the RGB source.

4) DVD/HD

Switches the input signal to the DVD/HD source.

5) PICTURE MODE

Selects Picture Mode: [STANDARD], [BRIGHT],

[CINEMA1], [CINEMA2], [DEFAULT].

STANDARD: for viewing in a bright room

BRIGHT: brighter picture than STANDARD

CINEMA1, 2: for viewing in a dark room, good for

movies

DEFAULT: factory default settings

6) SIZE

Set the aspect ratio of the image.

7) KEYPAD

Set REMOTE ID.

8) DISPLAY

Turn on/o the Information OSD.

9)

Move selection up or down

10) AUTO SETUP

Adjusts the CLOCK PHASE, CLOCK, and POSITION

settings automatically. (Analog RGB signal input only)

11) POINTER

Turn on/o the pointer.

12) VOLUME

Increases/Decreases sound level.

13) SPLIT SCREEN

PIP: Picture-in-Picture mode.

S BY S: Side-by-side mode.

SINGLE: Returns to normal mode.

SWAP: Swaps the Split Screen images.

SELECT/FREEZE: Selects which input is active when

in split screen mode.

When the PICTURE FREEZE function (see OSD

FUNCTION) is operating, SELECT/FREEZE can be

used to display still pictures on the sub screen.

CAPTURE : Captures still picture.

14) REMOTE ID

Activates REMOTE ID function.

15) MENU

Turns ON/OFF menu mode.

16) SET

Makes selection.

17) - , +

Increases or decreases amount of adjustment.

18) EXIT

Goes to the previous menu.

19) ZOOM

Enlarges or reduces the picture.

20) MUTE

Mutes audio output.

21) SLEEP

Sleep timer.

22) PICTURE MEMORY

Switches memory settings from 1 to 6.

PICTURE

MEMORY

POWER ON

RGB DVD/HD VIDEO

PICTURE

MODE

DISPLAY

AUTO

SET UP

VOL

SPLIT SCREEN

REMOTE ID

SWAP

SET RESET

REMOTE CONTROLLER RU-M113

SLEEP

SELECT/FREEZE

CAPTURE

PIP

S BY S SINGLE

MUTE

ZOOM

POINTER

EXIT

MENU

SIZE

STANDBY

123

456

78

0

9

SET

+

1

2

3

4

5

6

8

9

7

10

13

11

14

15

16

18

20

19

21

22

17

12

Remote Control Functions

English-12

POWER

To turn the unit ON and OFF:

1. Plug the power cord into an AC outlet.

2. Press the Power button (on the unit).

 e monitor's ON/STANDBY indicator turns red and

the unit will be in STANDBY mode.

3. Press the POWER ON button on the remote control.  e

ON/STANDBY indicator will turn green when the unit

is active.

4. Press the STANDBY button (on the remote) or the

Power button (on the unit) to turn o the monitor.

DISPLAY

To check display settings press the DISPLAY button on the

remote.  e screen changes each time the DISPLAY button is

pressed. Display information will disappear a er 3 seconds.

DIGITAL ZOOM

Digital zoom can change the picture position or enlarge the

image on the screen.

1. Be sure ZOOM NAV function is o . Press the ZOOM

button (+ or -) to display the magnifying glass.

Press the ZOOM + button to enlarge the image.

Press the ZOOM - button to reduce the image.

Press the UP and DOWN or PLUS and MINUS buttons

to reposition the picture.

2. Press the POINTER button to hide the pointer.

POINTER

Use the Pointer to point to a speci c area on the screen.

Press the UP and DOWN or PLUS and MINUS buttons to

reposition the Pointer.

Main Power Switch Cover

Included with the display is a cover for the Main Power

Switch. Use this cover to prevent the unit from being

inadvertently powered o .

Place the tab on the cable cover into the rectangular slot on

the display.

 en using the screw provided, secure the cover to the

display.

Part Names and Functions - continued

TAB

SLOT

OFFON

Main Power

Switch

Cover

English-13

REMOTE CONTROL ID

 e remote control included with the display can be used

to control up to 26 individual monitors using what is

called the REMOTE CONTROL ID mode.  e REMOTE

CONTROL ID mode works in conjunction with the Monitor

ID, allowing control of up to 26 individual monitors. For

example: if there are many monitors being used in the same

area, a remote control in normal mode would send signals to

every monitor at the same time Figure 1. Using the remote

in REMOTE CONTROL ID mode will only operate one

speci c monitor within the group Figure 2.

TO SET REMOTE CONTROL ID:

While holding down the REMOTE ID SET button on the

remote control, use the KEYPAD to input the Monitor ID

(1-26) of the display to be controlled via remote.  e remote

can then be used to operate the monitor having that speci c

Monitor ID number.

When 0 is selected or when the remote control is in normal

mode, all monitors will be operated.

TO USE REMOTE CONTROL ID MODE

ID Mode - To enter ID Mode press the REMOTE ID SET

button and hold down for 2 seconds.

Normal Mode - To return to Normal Mode press the

REMOTE ID RESET button and hold down for 2 seconds.

In order for this feature to work properly, the display must be

assigned a Monitor ID number.  e Monitor ID number can

be assigned under the SETUP menu in the OSD (See page

17).

If Monitor ID is set to “ALL” , monitor is controled by remote

control not depend on remote ID.

Monitor ID:1 Monitor ID:2

Remote does

not work

Remote does

not work

Figure 2

Remote set up to

use Remote ID:3

Monitor ID:1 Monitor ID:2

Remote works Remote works

Figure 1

Remote in Normal

mode or the REMOTE

ID is set to 0

Remote Control ID Function

Part Names and Functions - continued

Monitor ID:3

Remote works

Monitor ID:3

Remote works

English-14

On-Screen Display (OSD)

Using the OSD

Use the Remote Control or the control panel on the front

of the unit to enter the on-screen display menu to adjust

settings.

1. Press the MENU button on the remote or the EXIT

button on the Control Panel.

2. Use the up and down buttons to select the desired menu.

3. Press the SET button to select a sub-menu or item for

adjustment.

4. Change the setting or adjustment by pressing the + and

- buttons on the Control Panel or the Remote Control.

5. Press the EXIT button on the Remote Control, on the

Control Panel to return to the previous menu.

NOTE: Not all menu functions may be available. To access

all functions the Advanced OSD option must be

turned on in the ADVANCED OSD menu.

Press UP or DOWN

button to select

sub-menu.

Press SET. Press UP, DOWN, PLUS,

or MINUS to select the

function or setting to be

adjusted.

Press MENU or EXIT.

Press UP or DOWN

button to select.

Press INPUT

button to decide.

Press UP, DOWN, PLUS,

or MINUS to select.

Press EXIT.

Remote

Control

Panel

OSD Screen

ADVANCED OSD is OFF. Not all OSD functions will be

available when the ADVANCED OSD is off.

Advanced OSD is ON. All OSD functions are shown, but

some OSD functions may not be available.

PICTURE MEMORY

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

NR

COLOR TEMP.

FILM MODE

PICTURE MODE

OFF

HIGH

ON

STANDARD

VGA

PICTURE

4&- .&/64&- $-04&

FUNCTIONSCREEN

FUNC.

INFOSET UP

PICTURE MEMORY

CONTRAST

BRIGHTNESS

SHARPNESS

COLOR

TINT

NR

COLOR TEMP.

FILM MODE

PICTURE MODE

GAMMA

SET UP LEVEL

COLOR CONTROL

OFF

HIGH

ON

STANDARD

2.2

0%

VGA

PICTURE

FUNCTION

FUNC.

INFOSET UP

SCREEN

4&- .&/64&- $-04&

English-15

On-Screen Display (OSD)

Main Menu Sub Menu Sub Menu2 Explanation Default Reset

PICTURE PICTURE MEMORY Store picture menu settings and input terminal information. The

memory number is 1-6.

The "PICTURE MEMORY" screen appears when the SET button is

pressed on the "PICTURE MEMORY" MENU.

OFF YES

CONTRAST Adjusts the image brightness in relationship to the white level.

Press + or - to adjust.

50 YES

BRIGHTNESS Adjusts the image brightness in relationship to the background.

Press + or - to adjust.

50 YES

SHARPNESS Adjusts the crispness of the image. Press + or - to adjust. 50 YES

COLOR Adjusts the color depth of the screen. Press + or - to adjust. 50 YES

TINT Adjusts the tint of the screen. Press + or - to adjust. 50 YES

NR Adjusts the amount of noise reduction. Press + or - to adjust. OFF YES

COLOR TEMP. Adjusts the color temperature of the entire screen. A low

color temperature will make the screen reddish. A high color

temperature will make the screen bluish.

MIDDLE YES

WHITE BALANCE.

GAIN RED The "WHITE BALANCE" appears when the SET button is pressed

on the "COLOR TEMP." OSD menu.

GAIN RED/GREEN/BLUE: Adjusts the white level of the white

balance.

50 YES

GAIN GREEN 50 YES

GAIN BLUE 50 YES

RESET Resets the factory default settings. Select "ON", then press the

SET button to reset.

OFF YES

FILM MODE Selects Film mode. ON YES

PICTURE MODE Selects picture mode, [BRIGHT], [STANDARD], [CINEMA1],

[CINEMA2], [DEFAULT].

STANDARD: For watching in a bright room.

CINEMA1, 2: For watching in a dark room, especially good for

movies.

BRIGHT: Brighter picture than STANDARD.

DEFAULT: Restores factory default settings.

STANDARD YES

GAMMA

Available only when

the Advanced OSD

function in the

FUNCTION menu is

enabled.

Select a display gamma for best picture quality.

2.1, 2.2, 2.3, 2.4: The picture becomes darker as the number

increases.

S: Special gamma for certain types of movies. Raises the dark

parts and lowers the light parts of the image. (S-Curve)

These values are approximate.

2.2 YES

SET UP LEVEL

Available only when

the Advanced OSD

function in the

FUNCTION menu is

enabled.

Adjusts the video black level.

VIDEO signal input only.

0% YES

COLOR CONTROL

Available only when

the Advanced OSD

function in the

FUNCTION menu is

enabled.

RED Adjusts the levels of the Red, Green, Blue, Yellow, Magenta and

Cyan.

VIDEO and DVD/HD 1/2 input only.

50 YES

GREEN 50 YES

BLUE 50 YES

YELLOW 50 YES

MAGENTA 50 YES

CYAN 50 YES

RESET Resets the factory default settings. Select "ON", then press the

SET button to reset.

OFF YES

English-16

On-Screen Display (OSD)

Main Menu Sub Menu Sub Menu2 Explanation Default Reset

AUDIO BASS Adjusts the low frequency sound. Press + or - to adjust. 0 YES

TREBLE Adjusts the high frequency sound. Press + or - to adjust. 0 YES

BALANCE Adjusts the balance of L/R volume. Press + or - to adjust. 0 YES

AUDIO INPUT1 Select which audio input to use with the video source. VIDEO1 YES

AUDIO INPUT2 DVD/HD1 YES

AUDIO INPUT3 VGA YES

DVD/HD3 INPUT HDMI YES

SCREEN ASPECT MODE Selects aspect ratio of the displayed image. Press + or - to select. - -

V-POSITION Controls the vertical position of the image within the Display area

of the PDP.

Press + to move up. Press - to move down.

0YES

H-POSITION Controls the horizontal position of the image within the Display

area of the PDP.

Press + to move right. Press - to move left.

0YES

V-HEIGHT Adjusts the vertical size of the image. 0 YES

H-WIDTH Adjusts the horizontal size of the image. 0 YES

AUTO PICTURE ON: H-Position, V-Position, Clock and Clock Phase are adjusted

automatically.

OFF: H-Position, V-Position, Clock and Clock Phase are adjusted

manually.

VGA input only.

OFF NO

CLOCK PHASE Adjusts the visual “noise” on the image.

VGA input only.

0YES

CLOCK Press + to expand the width of the image on the right of the

screen.

Press - to narrow the width of the image on the left.

VGA input only.

0YES

UNDER SCAN

Available only when

the Advanced OSD

function in the

FUNCTION menu is

enabled.

ON: UNDERSCAN is selectable in the ASPECT MODE menu.

OFF: UNDERSCAN item is not selectable in the ASPECT MODE

menu.

Video signal input only.

OFF YES

SET UP

Some functions

available only

when the

Advanced OSD

function in the

FUNCTION

menu is

enabled.

The

LANGUAGE

and ALL

RESET

functions

are always

available.

LANGUAGE Select the language used by the OSD. ENGLISH NO

DVD/HD1 INPUT Selects whether to set the input of the DVD/HD1 connector.

COMPONENT : for Component input. (3BNC connectors)

SCART1 : for SCART input (3RCA connectors and VIDEO1 input)

(SCART1 available for Europe and World-Wide models only)

COMPONENT YES

D-SUB INPUT Selects whether to set the input of the mini D-SUB connector.

RGB : for RGB input

SCART2 : for SCART input

(SCART2 available for Europe and World-Wide models only)

RGB YES

HD SELECT Selects signal detection for similar 1080I signal manually.

1080I : Standard digital broadcasts

540P : Special digital broadcasts ( ex. DTC100 )

1080I NO

RGB SELECT If there is a problem with signal detection, this function forces the

monitor to display the signal at the desired resolution.

If no problem is detected, the only available option will be “AUTO”.

VGA input only.

AUTO YES

HDMI MODE Choose the HDMI mode based on the input device connected via

HDMI connector.

When a DVD player or similar equipment is connected, sets to

"HIGH".

When a PC or similar equipment is connected, sets to "LOW".

HIGH NO

DVI MODE PLUG/PLAY Choose the DVI mode based on the input device connected via

DVI connector and set the black level.

When a PC or similar equipment is connected, PLUG/PLAY is

"DVI-PC" and BLACK LEVEL is "LOW".

When a DVD player or similar equipment is connected, PLUG/

PLAY is "DVI-HD" and BLACK LEVEL is "HIGH".

DVI-PC NO

BLACK LEVEL LOW NO

COLOR SYSTEM The selected Color System depends on the video format of the

input signal.

VIDEO input only.

AUTO NO

English-17

On-Screen Display (OSD)

Main Menu Sub Menu Sub Menu2 Explanation Default Reset

SET UP

(continued)

BACK GROUND Chooses the brightness of background when there is no input

signal present.

GRAY YES

SIDE MASK Adjusts the color of the side mask when a 4:3 image is displayed.

Press + button, the bar will become lighter.

Press - button, the bar will become darker.

3YES

OSD DISPLAY OSD ON: Information about inputs, screen size, etc. is shown.

OFF: No information is shown.

ON YES

OSD

POSITION

Change the position of the menu between TOP LEFT and BTM

RIGHT. Press + or - to adjust.

TOP LEFT YES

OSD ORBITER ON: The menu position intermittently shifts eight dots while the

OSD is being displayed.

OFF: The menu position does not shift.

ON YES

OSD TRANSP. Adjusts the transparency level of the OSD.

Press + or - to adjust.

70% YES

MONITOR ID Sets the monitor ID number from 1-26 or to "ALL". ALL YES

ALL RESET Resets settings back to factory default values. OFF -

FUNCTION

Some functions

available only

when the

Advanced OSD

function in the

FUNCTION

menu is

enabled.

The

ADVANCED

OSD function

is always

available.

ADVANCED OSD ON: All menu items are shown for advanced users.

OFF: Some of the advanced menu items are not shown.

OFF YES

POWER SAVE Sets how long the monitor waits to go into power save mode after

a signal is lost.

VGA and DVI input and Separate HV sync. only.

OFF YES

INPUT SKIP Skips to next input if present input is no signal.

This function is valid only for INPUT key on the display.

OFF YES

SUB PICTURE SUB

P.D E T E C T

This function automatically detects no input signal of sub screen.

This feature is available only picture-in-picture mode.

SUB P. DETECT: Sets availability of automatic detecting of sub

screen.

DISPLAY: Sets the appearance method of the sub screen.

SUB P. RATE: Sets the transparency of the sub screen.

AUTO YES

DISPLAY NORMAL YES

SUB P.RATE 100% YES

ZOOM NAV Sets the position of the zoom navigation image. BTM LFT YES

PICTURE FREEZE Sets the position of the captured still picture. S BY S1 YES

SCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image

Persistence.

PEAK BRIGHT : The brightness is decreased depending on

setting.

ORBITER : The screen image moves slightly with squeezing or

expanding.

INVERSE : The screen image is displayed alternately between

positive image and negative image, or the screen image is

displayed full white.

MANUAL YES

PEAK BRIGHT 100% YES

ORBITER AUTO1 YES

INVERSE/

WHITE

OFF YES

CLOSED CAPTION

(U.S. models only)

Chooses the closed caption setting. OFF YES

CAPTION CONT

(U.S. models only)

Chooses the brightness of the closed caption. NORMAL YES

INPUT DETECT INPUT Sets the input mode and the sound volume when the power turn

on.

LAST : last mode (the input that was last selected when the power

turn off.)

MULTI to DVI : ﬁ xed input mode.

AUTO : Searches the input with the signal automatically

PRIORITY : Sets the priority input for AUTO setting.

LAST YES

VOLUME LAST YES

PROTOCOL SET Sets protocol setting of RS-232C.

OFF : When NEC protocol is used (normal).

ON : When special protocol is used.

* Consult your dealer for details of protocol.

OFF YES

RS232C CONTROL Selects the mode of the monitor when using the RS-232C daisy

chain.

NORMAL YES

SIGNAL INFORMATION Display signal information such as frequencies, polarities, etc. - -

English-18

Troubleshooting

No picture

 e signal cable should be properly connected to the display

card/computer.

 e display card should be properly seated in its slot.

Front Power Switch and computer power switch should be in

the ON position.

Check to make sure that a supported mode has been selected

on the display card or system being used. (Please consult

display card or system manual to change graphics mode.)

Check the monitor and your display card with respect to

compatibility and recommended settings.

Check the signal cable connector for bent or pushed-in pins.

Power Button does not respond

Unplug the power cord of the monitor from the AC outlet to

turn o and reset the monitor.

Image persistence

Please be aware that Plasma Technology may experience a

phenomena known as Image Persistence. Image Persistence

occurs when a residual or “ghost” image of a previous image

remains visible on the screen. Unlike CRT monitors, Plasma

monitors’ image persistence is not permanent, but constant

images being displayed for a long period of time should be

avoided. To alleviate image persistence, turn o the monitor

for as long as the previous image was displayed. For example,

if an image was on the monitor for one hour and a residual

image remains, the monitor should be turned o for one hour

to erase the image.

NOTE: As with all personal display devices, NEC DISPLAY

SOLUTIONS recommends displaying moving images and

using a moving screen saver at regular intervals whenever the

screen is idle or turning o the monitor when not in use.

Image is unstable, unfocused or

swimming is apparent

Signal cable should be properly attached to the Plasma

monitor, computer, or other input device.

Use the OSD screen controls to focus and adjust display by

increasing or decreasing the clock phase total. When the

display mode is changed, the OSD Image Adjust settings may

need to be readjusted.

Check the monitor and your display card with respect to

compatibility and recommended signal timings.

Image of component signal is greenish

Check to see if the DVD/HD input connector is selected.

LED on monitor is not lit

(no green or red color can be seen)

Main Power Switch should be in the ON position and power

cord should be connected.

Red LED on monitor is blinking

A certain failure might have occurred, please contact your

nearest authorized NEC DISPLAY SOLUTIONS service

facility.

•

Display image is not sized properly

Use the OSD screen controls to increase or decrease the clock

total.

Check to make sure that a supported mode has been selected

on the display card or system being used. (Please consult

display card or system manual to change graphics mode.)

Selected resolution is not displayed properly

Use OSD information to enter Information menu and con rm

that the appropriate resolution has been selected. If not, select

appropriate resolution.

No Sound

Check to see if speaker cable is properly connected.

Check to see if mute is activated.

Check to see if volume is set at minimum.

NOTE: It is possible to play audio from a source that is di erent

from the video source.

RS-232C does not work

Check the PROTOCOL SET in the FUNCTION menu.

Remote Control does not work

Make sure the batteries are inserted properly.

Test the batteries for strength/life.

Make sure to point the remote directly at the sensor on the

monitor.

Check if the remote is in Remote ID mode.

 e remote control may not function when in direct sunlight

or when there is strong illumination on the remote sensor of

the monitor.

•

Sayfa yükleniyor ...

NEC PlasmaSync® 60XC10 El kitabı

Bu kılavuz için de uygundur

NEC PlasmaSync® 60XC10 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler