HOTPOINT/ARISTON ADS93D 69 EU/B Kullanici rehberi

Marka: HOTPOINT/ARISTON

Model: ADS93D 69 EU/B

Kategori: Çamaşır makineleri

Tip: Kullanici rehberi

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

Care and maintenance, 4

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 5

General safety

Load balancing system

Disposal

Opening the porthole door manually

Description of the machine, 6-7

Touch control panel

Auto Dose System, 8-9

Running a wash cycle, 10

Wash cycles and options, 11

Table of wash cycles

Wash options

Detergents and laundry, 12

Detergent

Preparing the laundry

Washing recommendations

Trouble shooting, 13-14

Assistance, 15

AQUALTIS

ADS93D 69

Instructions for

installation and use

English,1

Türkçe,33

TRGR

ΕΛΛΗΝΙΚΑ, 17

Українська,49

WASHING MACHINE

Installation

! This instruction manual should be kept in a

safe place for future reference. If the washing

machine is sold, given away or moved, please

ensure the manual is kept with the machine,

so that the new owner may benefit from the

advice contained within it.

! Read these instructions carefully: they

contain vital information relating to the safe

installation and operation of the appliance.

! Inside the pack containing this manual, you

will also find the guarantee and all the details

necessary for installation.

Unpacking and levelling

Unpacking

1. Once you have removed all the packaging

from the washing machine, make sure it has not

been damaged during transportation. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

2. Remove the 4

protective screws

(used during

transportation) and

the corresponding

spacer, located on

the rear part of the

appliance (see figure).

3. Close off the holes using the plastic plugs

supplied in the pack.

4. Keep all the parts in a safe place; they will

be needed again if the washing machine is

moved to another location, to prevent the

inside of the appliance being damaged.

! Packaging materials should not be used as

toys for children.

Levelling

1. Place the washing machine on a flat sturdy

floor, without resting it up against walls or

cabinets.

2. If the floor is

uneven, the front feet

of the machine may

be adjusted until it

reaches a horizontal

position (the angle of

inclination must not

exceed 2 degrees).

! If the appliance is levelled correctly, it will

be more stable and much less likely to cause

vibrations and noise while it is operating,

particularly during the spin cycle.

! If it is placed on carpet or a rug, adjust the

feet in such a way as to allow a sufficient

ventilation space underneath the washing

machine.

Connecting the electricity and

water supplies

Connecting the water inlet hose

! Before connecting the inlet hose to the water

supply, run the water until it is perfectly clear.

1. Connect the inlet

hose to the machine

by screwing it onto

the cold water inlet of

the appliance, which

is situated on the top

right-hand side of

the rear part of the

appliance (see figure).

2. Connect the inlet

hose by screwing it to

a cold water tap using

a 3/4 gas threaded

connection (see

figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical data table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand or old inlet hoses;

use the products supplied with the machine.

Technical data

Model

ADS93D 69

Dimensions

width 59.5 cm

height 85 cm

depth 64,5 cm

Capacity

from 1 to 9 kg

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water con-

nections

maximum pressure

1 MPa (10 bar)

minimum pressure

0.05 MPa (0.5 bar)

drum capacity 62 litres

Spin speed

up to 1600 rotations per

minute

Test wash

cycles in

accordan-

ce with

directives

1061/2010

and

1015/2010

programme

;

Cotton standard 60°C.

programme ;

Cotton standard 40°C.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electroma-

gnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU

Connecting the drain hose

Connect the drain

hose to drain duct

piping or a wall drain

located between 65

and 100 cm above

the floor, making sure

it is not bent at all.

Alternatively, rest the

drain hose on the

side of a washbasin

or bathtub, fastening

the duct supplied to

the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose

and must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the

electricity socket, make sure that:

• the socket is earthed and complies with all

applicable laws;

• the socket is able to withstand the maximum

power load of the appliance as indicated in

the Technical data table (see opposite);

• the power supply voltage falls within the

values indicated in the Technical data table

(see opposite);

• the socket is compatible with the plug of the

appliance. If this is not the case, have the

socket or the plug replaced.

! The machine must not be installed outdoors,

even in covered areas. It is extremely

dangerous to leave the appliance exposed to

rain, storms and other weather conditions.

! The mains socket must remain within easy reach

after the washing machine has been installed.

! Do not use extension cords or multiple

sockets.

! The cable should not be bent or compressed.

! The power supply cable and plug must only

be replaced by authorised technicians.

Warning! The company shall not be held

responsible in the event that these regulations

are not respected.

65 - 100 cm

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. take off the cover panel on the front of the

machine by first pressing it in the centre and

then pushing downwards on both sides until

you can remove it (see figures);

2. position a container

so that it will collect the

water which flows out

(approximately 1.5 l)

(see figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

6. reposition the panel, making sure the hooks

are securely in place before you push it onto

the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

Cutting off the water and

electricity supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system in

the machine and help to prevent leaks.

• Unplug the appliance when cleaning it and

during all maintenance work.

Cleaning the machine

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

To pull out the dispenser drawer, open until

the first stop point then press lever A to open

completely; finally, press one of the levers D and

pull the drawer outwards (see picture).

Wash it under running water; this procedure

should be effected regularly. Be careful to remove

any detergent residues from the dispenser

drawer socket on the machine.

Keep the drawer to the left hand side when

replacing it to ensure that it centres the guides

and to prevent it from jamming.

Caring for your appliance drum

• Always leave the door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-

cleaning pump which does not require any

maintenance. Sometimes, small items (such

as coins or buttons) may fall into the protective

pre-chamber at the base of the pump.

Care and maintenance

Precautions and tips

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

•

This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use of

the appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washing machine, make

sure the drum is empty.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the load is

excessively unbalanced, the washing machine performs

the distribution process instead of spinning. To encourage

improved load distribution and balance, we recommend

small and large garments are mixed in the load.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2012/19/EU relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the materials

inside the machine, while preventing potential damage

to the atmosphere and to public health.

The crossed-out dustbin is marked on all products

to remind the owner of their obligations regarding

separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole door

due to a powercut, and if you wish to remove the laundry,

proceed as follows:

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if

it is not, remove excess

water using the drain hose,

collecting it in a bucket as

indicated in the figure.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is freed

from its stop position; pull

downwards until you hear a

“click”, which indicates that

the door is now unlocked.

5. open the door; if this is

still not possible repeat the

procedure.

6. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

PORTHOLE DOOR

Always use the handle to

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

The detergent dispenser

drawer is located inside

the machine and can be

accessed by opening the

door.

Refer to the chapter “Auto

Dose System” for information

on operation.

TOUCH CONTROL PANEL

To adjust the settings, gently

press the icon inside the

sensitive (touch control) area

as illustrated in the figure.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF

button briefly and

wait for the machine to start up again.

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

WASH CYCLE

SELECTOR knob

Button with

ON/OFF

indicator light

Touch control panel

TEMPERATURE

button

OPTION

buttons

DISPLAY

ECO

indicator light

START/PAUSE button

with indicator light

LOCK

indicator light

WASH CYCLE

PHASE icons

SPIN SPEED

button

DELAY

TIMER button

CHILD LOCK button

with indicator light

Button with ON/OFF indicator light: press this briefly to switch

the machine on or off. The green indicator light indicates that the

machine is switched on. To switch off the washing machine during

the wash cycle, press and hold the button for approximately

3 seconds; if the button is pressed briefly or accidentally the

machine will not switch off. If the machine is switched off during

a wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR knob: may be turned in either

direction. To select the most suitable wash cycle, please refer

to the “Table of wash cycles”.

The knob will not move during the wash cycle.

TEMPERATURE

button: press to modify or exclude the

temperature setting; the value selected will appear on the display

above (see “Running a wash cycle”).

SPIN SPEED CYCLE

button: press to modify or exclude the

spin cycle; the value selected will appear on the display above

(see “Running a wash cycle”).

DELAY TIMER

button: press to set a delayed start for the

selected wash cycle; the set delay time will appear on the display

above (see “Running a wash cycle”).

OPTION buttons with indicator lights: press to select the available

options. The indicator light corresponding to the selected option

will remain lit (see “Running a wash cycle”).

DETERGENT and SOFTENER buttons : refer to

“Modifying pre-set parameters” in the chapter “Auto Dose System”.

DETERGENT DILUTION button: refer to “Filling the tanks”

in the chapter “Auto Dose System”.

WASH CYCLE PHASE icons: these illuminate to indicate the

progress of the wash cycle (Wash

– Rinse – Spin –

Drain

). The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a wash

cycle. Once the cycle has begun the indicator light will remain

lit in a fixed manner. To pause the wash cycle, press the button

again; the indicator light will flash in an orange colour.

If the “LOCK”

indicator light is switched off, the door may be

opened. To start the wash cycle from the point at which it was

interrupted, press the button again.

LOCK

indicator light: indicates that the porthole door is

locked. To open the door, pause the wash cycle (see “Running

a wash cycle”).

CHILD LOCK

button with indicator light: to activate or

deactivate the control panel lock, press and hold the button for

approximately 2 seconds. when the indicator light is illuminated,

the control panel is locked

(apart from the ON/OFF button). This

means it is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the home.

ECO indicator light: the

icon lights up when, after altering the

washing parameters, an energy saving of at least 10% is made.

Furthermore, before the machine enters “Standby” mode, the

icon will light up for a few seconds; when the machine is switched

off the estimated energy saving will be around the 80% mark.

CHANGE LANGUAGE

The first time the machine is switched on, the first language

will flash on the display. The

“

“, “OK” and “V” symbols will appear on the display, in line

with the 3 buttons on the right-hand side. The languages

change automatically every 3”; alternatively, they can be

changed by pressing the buttons next to the “

“ and “V”

symbols. Use the “OK” button to confirm the language, which

will be set after 2”. If no buttons are pressed, the automatic

language change will begin again after 30”.

To change the language, switch the machine on and off

again; in the 30” time period after it has been switched

off, press and hold the temperature

+spin

+delayed

start buttons simultaneously for 5’’. A short

sound alert will be emitted and the set language will flash

on the display.

Press the buttons next to the “ “ and “V”

symbols to change the language. Use the button next to the

“OK” symbol to confirm the language, which will be set after

2”. If no buttons are pressed, the language set previously will

be displayed after 30”. Switch on the machine.

DETERGENT

button

SOFTENER

button

DETERGENT

DILUTION

button

Auto Dose System

Introduction

This washing machine is

equipped with two tanks: one

for liquid detergent (either

concentrated or diluted) with

a capacity of approx. 5.5 l

and another for liquid fabric

softener (either concentrated

or diluted) with a capacity of

approx. 3.5 l (see picture).

! Check the detergent/fabric

softener box to verify whether

it is diluted or concentrated

detergent. The automatic

dosing system intakes the

correct amount of detergent and fabric softener from the

tanks for each type of load and at the right time, guaranteeing

optimal washing results without wastage. The amount of

detergent/fabric softener can be modified manually by

pressing the DETERGENT and FABRIC SOFTENER buttons

(refer to “Modifying pre-set parameters”). If you prefer, the

washing machine can also be used in the “traditional” mode,

i.e. by adding the detergent in the dispenser; the machine will

automatically detect the detergent and will not use the tanks.

Detergent dispenser

“Traditional” mode.

Pull out the detergent dispenser drawer up to the first stop

point to add the detergent (either liquid or powder detergent),

bleach or other additives (e.g. whiteners) and the pre-wash

detergent for washing in the “traditional” mode (refer to

“Traditional” mode).

“Auto Dose System” mode.

In order to fill the detergent

and fabric softener tanks, the

detergent dispenser drawer

must be fully extracted:

open the dispenser drawer

up to the first stop point then

press the lever (A) and open

up to the second stop point,

making sure that it is fully

extracted. Avoid moving

the dispenser drawer during

filling operations. Once the tanks have been filled (refer to

“Filling the tanks”), the machine can run up to 40 cycles before

the detergent finishes (*).

First-time use

Turn the washing machine on by pressing the ON/OFF button.

The first wash cycle must be carried out without laundry

and by adding detergent in the detergent dispenser (refer

to “Traditional” mode); set the programme “

“ (Cotton 90°)

without pre-wash and without filling the tanks.

Filling the tanks:

Open the detergent dispenser drawer in the “Auto Dose

System” mode (refer to “Detergent dispenser”).

Slowly pour the detergent (B) and fabric softener (C)

until the tanks are completely filled (see picture).

To avoid exceeding the maximum capacity, a buzzer (beep)

will sound with growing intensity to signal the level and 3 long

beeps will sound once the tank is completely full.

Start the wash cycle immediately after filling the tanks to

ensure that the dispenser is properly cleaned.The respective

icons

(for the detergent) and (for the fabric softener) will

light up gradually to signal the level.

The filling time depends on the density of the product. Very

dense products will take longer to fill.

Close the detergent dispenser drawer only once the

compartments are completely empty.

Select the density of the detergent added (either concentrated

or liquid) by pressing the appropriate button

Concentrated

Diluted

The machine will store the selection.

If no option is selected, the detergent intake option will be

pre-set to “diluted”.

Use button

to set the amount of fabric softener that will

be automatically extracted by the machine:

1) If concentrated softener is used, we recommend selecting

the first level (

with one bar) and, if necessary, stepping up

by a single position (

with 2 bars) to increase detergent

intake.

2) If diluted softener is used, we recommend setting level

3 (

with 3 bars) and to then either increase/decrease the

amount of fabric softener to be extracted.

3) To exclude the use of fabric softener, press

until the

bars disappear (also refer to “Modifying pre-set parameters”).

(*) with an average load of 4 kg, 40°C Cotton programme, “medium” water hardness

level and dirt level set to 3.

Signals for successive refilling:

Once, at the end of a cycle, the level of detergent/fabric

softener falls below the level required for a successive

wash cycle, the display will visualise the relative messages

“At end of cycle refill detergent” or “At end of cycle refill

softener” or “At end of cycle refill tanks”. If the tanks are

not filled, the successive wash cycles in Auto Dose System

will be carried out without any intake of detergent.

! We suggest adding detergent and fabric softener ONLY

after the machine’s signal.

! NEVER mix two different detergents; always clean out

the tank before adding a new type of detergent (refer to

“Cleaning cycle set by the user”).

Using the “Auto Dose System”

If the compartments have been filled with detergent and

fabric softener, you may start using the machine (refer to

“Running a wash cycle”).

Powder detergents for pre-washing and powder

additives may only be used in the traditional mode or

using the “Auto Dose System”, by placing the additives

directly inside the drum, preferably in conjunction with the

“laundry ball”.

Whenever bleaching is required, pour the bleach in the

relative compartment (refer to the option “Super Wash”).

Modifying pre-set parameters:

The machine automatically intakes detergent on the

basis of the selected programme, wash load and water

hardness. However, the amount of detergent/fabric

softener used may be modified.

button: press to increase, decrease and to exclude

detergent intake.

button: press to increase, decrease and to exclude

fabric softener intake.

The level of detergent/fabric softener suggested by the

machine is indicated by 3 bars.

Less than 3 bars indicates a lower level of detergent/

fabric softener compared to that suggested by the

machine, while more than 3 bars indicates a higher level of

detergent/fabric softener.

Cleaning the tanks:

Tank cleaning cycles can either be automatic or pre-set by

the user.

Automatic cleaning:

The washing machine carries out an automatic cleaning

cycle during the rinse cycle if the level of detergent that

remains is insufficient for carrying out a

successive wash cycle.

Cleaning cycle set by the user:

Run the cleaning cycle (with empty drum) if you require

adding a different product to the previous one or if the tanks

have been incorrectly filled (e.g. fabric softener has been

erroneously poured into the detergent tank or vice-versa).

Press button

and hold for 5 sec. to activate cleaning of

the detergent tank, button

for cleaning the fabric softener

tank or button

for cleaning both tanks. Keep pressing for

a further 3 sec. (the countdown “4-3-2-1” will appear in the

top right corner) until “CLEAN-GO” pops up.

The cleaning cycle lasts about 65’ if the tanks are initially

empty; if not, the cycle will last longer. The icons indicating

that the tanks are empty will appear on the display.

“Traditional” mode

Pull out the detergent dispenser drawer up to the first stop

point (see picture) then pour the amount of detergent and

other additives (e.g. bleach) required for a single wash cycle

directly into the dispenser.

1. pre-wash compartment: use

powder detergent only.

2. main wash compartment:

use powder or liquid detergent.

If the latter is used, we

recommend pouring it into the

dispenser immediately before

starting the washing machine

and without running a pre-

wash cycle.

3. bleach compartment: to be used whenever bleaching is

required (refer to “Super Wash” option).

Tablet detergent or the relative “laundry ball” must be added

directly inside the drum. In this event, deactivate the “Auto

Dose System” (by pressing the

button until the relative

vertical bars disappear from the display).

Do not pour any fabric softener as the appropriate quantity

required for each wash cycle will be automatically extracted.

To deactivate fabric softener intake, press the

button until

the vertical bars disappear from the display.

For wool and silk garments, we recommend using a special

detergent which must be poured directly into the detergent

dispenser (compartment 2).

Running the wash cycle:

Select the programme and the compatible options on the

basis of the required need and type of load.

Running a wash cycle

WARNING: before you use the washing machine for the first

time, run a wash cycle with detergent and no laundry, using

the 90° cottons cycle without pre-wash.

1. SWITCH THE MACHINE ON. Press the

button. All

the indicator lights will illuminate for 1 second and the text

AQUALTIS will appear on the display; the indicator light

corresponding to the

button will then remain lit in a constant

manner and the START/PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has been

selected; the name of the programme will appear on the

display. A temperature and spin speed is set for each

programme; these may be adjusted. The cycle duration

will also appear on the display.

3. LOAD THE LAUNDRY. Open the porthole door. Load the

laundry, making sure you do not exceed the maximum load

value indicated in the table of wash cycles on the following

page.

4. MEASURE OUT THE DETERGENT. There is no need

to add detergent when the “Auto Dose System” mode is

used, as the machine automatically intakes detergent on the

basis of the selected programme, type of load and water

hardness. Refer to the paragraph “Traditional” mode for

implementing the traditional operation mode.

5. CLOSE THE PORTHOLE DOOR.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum

temperature and spin speed values set for the selected

cycle, or the most recently-used settings if they are

compatible with the selected cycle. The temperature

can be decreased by pressing the

button, until the

cold wash “OFF” setting is reached. The spin speed may

be progressively reduced by pressing the

button,

until it is completely excluded “OFF”. If these buttons

are pressed again, the maximum values are restored.

! Exception: if the

programme is selected, the

temperature can be increased up to a value of 90°C.

Set a DELAY TIMER

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. During the setting procedure, the

delay period and the text “Starts in:” will be displayed, along

with the flashing

symbol. After the delayed start has been

set, the

symbol will remain fixed on the display, which will

also indicate the duration of the selected cycle with the text

“Ends in:” and the cycle duration. Press the DELAY TIMER

button just once to display the delay time set previously. After

the countdown has begun, the display will show the text

“Starts in:” and the delay period.

Once the set delay time has elapsed, the machine will begin

its cycle and the display will show “Ends in:” and the time

remaining until the end of the cycle. To remove the delayed

start option, press the button until the display shows the text

OFF; the

symbol will disappear.

Modify the cycle settings.

• Press the button to activate the option; the name of the

option will then appear on the display and the corresponding

indicator light will illuminate.

• Press the button again to deactivate the option; the name

of the option will then appear on the display followed by

the text OFF, and the corresponding indicator light will

switch off.

! If the selected option is not compatible with the selected

wash cycle, this incompatibility will be signalled by the

flashing of the indicator light and a sound alert (3 beeps);

the option will not be activated.

! If the selected option is not compatible with another option

that has been selected previously, the indicator light

corresponding to the first option selected will flash and

only the second option will be activated; the indicator light

corresponding to the button will remain lit in a constant

manner.

! The options may affect the recommended load value and/or

the duration of the cycle.

7. START THE PROGRAMME. Press the START/PAUSE

button. The corresponding indicator light remains lit in a

fixed manner and the porthole door locks (the

LOCK

indicator light illuminates). The icons corresponding to

the wash cycle phases will light up during the cycle to

indicate which phase is currently in progress. To change a

wash cycle once it has already started, pause the washing

machine by pressing the START/PAUSE button; then select

the desired cycle and press the START/PAUSE button

again. To open the door during a wash cycle, press the

START/PAUSE button; if the LOCK

indicator light is

switched off you may open the door. Press the START/

PAUSE button again to restart the wash cycle from the

point at which it was interrupted.

8. THE END OF THE WASH CYCLE. This is indicated by

the illuminated text END. The porthole door may be opened

immediately. If the START/PAUSE indicator light is flashing,

press the button to end the cycle. Open the door, unload

the laundry and switch off the machine.

! If you wish to cancel a cycle which has already begun, press

and hold the

button until the cycle stops and the machine

switches off.

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to wash

even the most valuable and delicate garments in complete

confidence thanks to the special bag which protects the

laundry (this is supplied with the machine). We recommend

that the bag is used every time you wash quilts and

padded items with an outer layer made using synthetic

material.

Wash cycles and options

Wash options

Super Wash

This option offers a high-

performance wash due to

the greater quantity of water

used in the initial phase of

the cycle, and due to the

increased wash cycle duration,

is particularly useful for the

removal of stubborn stains. It

can be used with or without

bleach. If you desire bleaching,

use the compartment 3.

When dosing the bleach,

be careful not to exceed the “max” level (see figure).

To bleach laundry without carrying out a full wash cycle,

pour the bleach into the compartment 3, select the “Rinse”

cycle

and activate the “Super Wash” option .

! It cannot be used in conjunction with

, , , , ,

, , .

Extra rinse

By selecting this option, the efficiency of the rinse is increased

and optimal residual detergent removal is guaranteed. It is

particularly useful for skin which is sensitive to detergents. We

recommend this option is used with a full load of washing, or

when a large amount of detergent is required.

! It cannot be used in conjunction with

, , , , .

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum will

rotate slowly; the “Easy Iron” and START/PAUSE indicator

lights will flash. To end the cycle press the START/PAUSE

button or the “Easy Iron” button.

! It cannot be used in conjunction with

, , , , , .

Prewash

If this function is selected, the pre-wash cycle will run; this is

useful for removing stubborn stains.

N.B.: put the detergent in the relevant compartment.

! It cannot be used in conjunction with

, , , , ,

, , , , (60°), , .

Table of wash cycles

Icon

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Detergent and additives

Max. load (kg)

Residual

dampness %

Energy con-

sumption kWh

Total water lt

Cycle dura-

tion

Prewash

Wash

Bleach

Fabric

softener

Synthetics Resistant 60° 800

   

5 46 1,03 60 115’

Synthetics Resistant (4) 40° 800

   

5 46 0,56 60 100’

Whites

60° 1600

 



5 - - - 180’

Coloureds

40° 1600

   

5 44 0,83 63 100’

Darks

30° 800 -



5 - - - 80’

Shirts

40° 600 -

  

2 - - - 70’

Duvets: for down-stuffed garments. 30° 1200 -



3,5 - - - 120’

Bed&Bath for bedlinen and towels. 60° 1600

   

9 - - - 140’

Rinse

- 1600 - -

 

9 - - - 36’

Spin and Pump out - 1600 - - - - 9 - - - 16’

Anti Allergy

60° 1600 -



5 - - - 195’

Ultradelicates

30° 0 -



1 - - - 80’

Wool: for wool, cashmere, etc. 40° 800 -



2 - - - 90’

Mix 30': to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

30° 800 -



3,5 71 0,20 38 30’

Cotton Standard 60°C (1): heavily soiled whites and resistant colours.

60°

(Max. 90°)

1600

(3)

  

9 44 1,19 57,5 205’

Cotton Standard 40°C (2): lightly soiled whites and delicate colours. 40° 1600 -

  

9 44 1,09 92 180’

Cotton Standard 20°C: lightly soiled whites and delicate colours. 20° 1600 -

  

9 - - - 175’

Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value

will then be shown on the display.

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

1) Test wash cycle in compliance with directive 1061/2010: set wash cycle with a temperature of 60°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.

2) Test wash cycle in compliance with directive 1061/2010: set wash cycle

with a temperature of 40°C.

This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for

garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.

3) At 60 °C the “Prewash” function cannot be selected.

For all Test Institutes:

2) Long wash cycle for cottons: set wash cycle

with a temperature of 40°C.

4) Long wash cycle for synthetics: set wash cycle

with a temperature of 40°C.

Shirts: use the special wash cycle to wash shirts in

different fabrics and colours to guarantee they receive the

best possible care.

Duvets: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

special

wash cycle. We recommend that duvets are

placed in the drum with their edges folded inwards (see

figure) and that no more than ¾ of the total volume of the

drum is used. To achieve the best results, we recommend

that a liquid detergent is used and placed inside the

detergent dispenser drawer.

Quilts: to wash quilts with a synthetic outer layer, use the

bag provided and set the wash cycle to

Bedlinen and towels: Use programme

to wash bed

linen and towels in one single cycle: it optimises softener

performance and helps you save time and energy. We

recommend the use of powder detergent

Anti Allergy: use programme

to remove major allergens

such as pollen, mites, cat’s and dog’s hair.

Ultradelicates: use programme

to wash very delicate

garments having strasses or sequins.

We recommend turning the garments inside out before

washing and placing small items into the special bag

for washing delicates. Use liquid detergent on delicate

garments for best results.

To wash Silk garments and Curtains (these should be folded

and placed inside the bag provided), select cycle

and then

option

(in this case it will also be possible to enable the

“Extra Rinse” option); the machine will end the cycle while

the laundry is soaking and the

indicator light will flash.

To drain the water so that the laundry may be removed,

press the START/PAUSE button or the

button.

Wool: the wool wash cycle on this Hotpoint-Ariston

machine has been tested and approved by The

Woolmark Company for washing wool garments labelled

as hand washable provided that the garments are

washed according to the instructions on the garment

label and those issued by the manufacturer of this

washing machine. Hotpoint-Ariston is the first washing

machine brand to be approved by The Woolmark

Company for Apparel Care- Platinum for its washing

performance and consumption of energy and water.

(M1127)

In UK, Eire, Hong Kong and India the Woolmark trade mark

is a Certification trade mark.

Cotton Standard 20°C: ideal for lightly soiled cotton

loads. The effective performance levels achieved at cold

temperatures, which are comparable to washing at 40°,

are guaranteed by a mechanical action which operates at

varying speed, with repeated and frequent peaks.

Detergents and laundry

Detergent

The type and quantity of detergent required depend on the

type of fabric you are washing (cotton, wool, silk, etc.), as

well as its colour, the washing temperature, the level of soiling

and the hardness of the water in the area.

Whenever the detergent and fabric softener “Auto Dose

System” is activated, this washing machine helps to

prevent wastage and to protect the environment, besides

guaranteeing optimal washing performance.

We recommend the following:

• Use powder detergent for carrying out a pre-wash and

pour in the “traditional” mode.

• Use liquid detergents for delicate cotton garments and for

all low-temperature wash cycles.

• When activating the “Auto Dose System” mode, use liquid

detergent and fabric softeners only. Never add ultra-

concentrated detergents (e.g. “Gel” type detergents

or similar).

• Use gentle liquid detergents for wool and silk garments

and pour in the “traditional” mode.

! Never mix two different detergents; always clean out the

tank before adding a new type of detergent.

The detergent should be poured into the relevant compartment

- or the dispenser placed directly inside the drum - before the

wash cycle begins. In the latter case, it will not be possible

to select the Cottons with pre-wash cycle.

! Use powder detergent for white cotton garments, for

pre-washing, and for washing at temperatures over 60°C

! Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the

machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillowcase 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

1 pair of jeans 400-500 g

1 shirt 150-200 g

Washing recommendations

Whites: use this cycle to wash white clothes. The

programme is designed to maintain the brightness of

white clothes over time.

Coloureds: use this cycle

to wash bright coloured

clothes. The programme is designed to maintain bright

colours over time.

Darks: Use cycle

to wash dark-coloured garments.

This programme is designed to maintain dark colours

over time. We recommend using a liquid detergent for the

best results when washing dark-coloured garments.

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be solved easily using the following list.

Problem:

The washing machine does not

switch on.

The wash cycle does not start.

The washing machine does not fill

with water.

The washing machine door

remains locked.

The machine continuously fills

with water and drains.

The washing machine does not

drain or spin.

The machine vibrates a lot during

the spin cycle.

The washing machine leaks.

The icons corresponding to the

“Phase in progress” flash rapidly

at the same time as the ON/OFF

indicator light.

There is too much foam.

The washing machine door

remains locked.

“AutoDose disabled, use the

dispenser drawer” appears on the

display.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make

contact.

• There is no power in the house.

• The door is not closed properly.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set.

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• If you have selected the

function, at the end of the cycle the washing

machine drum will rotate slowly; to end the cycle press the START/PAUSE

button or the

button.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to fill with

water and drain continuously. Special anti-draining valves are available in shops

and help to prevent this inconvenience.

• The wall drainage system is not fitted with a breather pipe.

• The wash cycle does not include draining: Some wash cycles require the drain

phase to be started manually (see “Wash cycles and options”).

• The “Easy iron” option is enabled: to complete the wash cycle, press the

START/PAUSE button (“Wash cycles and options”).

• The drain hose is bent (see Installation).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The machine is not level (see “Installation” ).

• The machine is trapped between cabinets and walls (see “Installation”).

• The load is unbalanced (see “Detergents and laundry”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser is blocked (to clean it, see “Care and maintenance”).

• The drain hose is not fixed in place properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

• Perform the manual unlocking procedure (see “Precautions and tips”).

• Indicates malfunctioning of the AutoDose system. Use the machine traditionally,

by pouring the detergent and fabric softener required for a wash cycle into

the drawer, and contact the Assistance service to establish the cause(s) of the

malfunction.

Troubleshooting:

The machine’s washing performance

is unsatisfactory.

What happens if the tanks are loaded

even if they are already full?

What happens if the dispenser is used

in the traditional mode while the tanks

are still full?

Can the tanks also be used for

powder detergent?

Can powder detergent fall into the

tanks?

What happens if the dispenser is

not opened properly when filling the

tanks?

What happens if detergent and fabric

softener are erroneously inverted?

What happens if different detergents

are mixed before the tanks are

empty?

Possible causes / Solutions:

• The tanks have not been loaded correctly (e.g. fabric softener has been

added instead of detergent or vice-versa)

• Two different types of detergent/fabric softener have mixed.

 ! NEVER mix two different detergents; always clean out the tanks before adding

a new type of detergent.

• The “Auto Dose System” is blocked due to prolonged lack of use: carry out

a tank cleaning cycle (refer to “Cleaning cycle set by the user”).

• Buzzers (Beep) and visual signals (icons appearing on the display) indicate

that the tank is full. If further detergent/fabric softener is added, the excess

quantity will fall into the drum and will be washed away with the next cycle.

• The machine will automatically track whether powder or liquid detergent

has been loaded in the traditional mode and will not intake any amount of

detergent from the tank. Fabric softener can only be used in the “Auto Dose

System” mode.

• No, powder detergent can only be used in the traditional mode.

• No, there is a barrier to prevent powder detergent from falling into one of

the tanks even if the dispenser is open in the “Auto Dose System” position

(i.e. completely open).

• If the dispenser is not completely open, the detergent or fabric softener that

has been added will fall into the drum and will be washed away with the

next cycle.

• The washing machine will wash with unsatisfactory results, the tanks will

have to be emptied and subjected to a manual cleaning cycle.

• The machine will wash normally although we recommend only refilling

the tanks after the signal emitted by the machine; do not mix different

detergents/fabric softeners.

Note: to exit “Demo mode”, switch machine off, press and hold the two “START/PAUSE” and “ON/OFF” buttons

simultaneously for 3 seconds.

Assistance

Before calling for Assistance:

• Check whether you can solve the problem by yourself (see “Trouble shooting”);

• Restart the wash cycle to check whether the problem has been solved;

• If it has not, contact the Authorised Technical Assistance Service.

! If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.

! Always request the assistance of authorised technicians.

Please have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

The above information can be found on the data plate located on the appliance itself.

Ελληνικά

Περιεχόμενα

Εγκατάσταση, 18-19

Αποσυσκευασία και οριζοντίωση

Υδραυλικές και ηλεκτρικές συνδέσεις

Τεχνικά στοιχεία

Συντήρηση και φροντίδα, 20

Αποκλεισμός νερού και ηλεκτρικού ρεύματος

Καθαρισμός της μηχανής

Καθαρισμός του συρταριού απορρυπαντικών

Φροντίδα του κάδου

Καθαρισμός της αντλίας

Έλεγχος του σωλήνα τροφοδοσίας του νερού

Προφυλάξεις και συμβουλές, 21

Γενική ασφάλεια

Σύστημα ισοστάθμισης του φορτίου

Διάθεση

Χειρονακτικό άνοιγμα της πόρτας

Περιγραφή της μηχανής, 22-23

Πίνακας χειριστηρίων touch control

Auto Dose System, 24-25

Πως διενεργείται ένας κύκλος πλυσίματος, 26

Προγράμματα και δυνατότητες, 27

Πίνακας Προγραμμάτων

Οι δυνατότητες πλυσίματος

Απορρυπαντικά και μπουγάδα, 28

Απορρυπαντικό

Προετοιμασία της μπουγάδας

Συμβουλές πλυσίματος

Ανωμαλίες και λύσεις, 29-30

Υποστήριξη, 31

AQUALTIS

ADS93D 69

Οδηγίες για την

εγκατάσταση και τη χρήση

ΠΛΥΝΤΗΡΙΟ

Εγκατάσταση

! Είναι σημαντικό να διατηρήσετε το

εγχειρίδιο αυτό για να μπορείτε να το

συμβουλεύεστε οποιαδήποτε στιγμή. Σε

περίπτωση πώλησης, παραχώρησης ή

μετακόμισης, βεβαιωθείτε ότι παραμένει μαζί

με το πλυντήριο.

! Διαβάστε προσεκτικά τις οδηγίες:

υπάρχουν σημαντικές πληροφορίες για την

εγκατάσταση, τη χρήση και την ασφάλεια.

! Στη σακουλίτσα που περιέχει το εγχειρίδιο

αυτό θα βρείτε, εκτός της εγγύησης, υλικά

που χρησιμεύουν για την εγκατάσταση.

Αποσυσκευασία και οριζοντίωση

Αποσυσκευασία

1. Αφού αποσυσκευαστεί το πλυντήριο,

ελέγξτε αν έχει υποστεί ζημιές κατά τη

μεταφορά.

Αν έχει υποστεί ζημιές μην το συνδέετε και

επικοινωνήστε με τον μεταπωλητή.

2. Αφαιρέστε τις 4

προστατευτικές βίδες

για τη μεταφορά και

τον σχετικό αποστάτη

που βρίσκονται στο

πίσω μέρος (βλέπε

εικόνα).

3. Κλείστε τις οπές με τα πλαστικά πώματα

που περιέχονται στη σακουλίτσα.

4. Φυλάξτε όλα τα κομμάτια. Αν το

πλυντήριο χρειαστεί να μεταφερθεί, θα

πρέπει να ξαναμονταριστούν για την

αποφυγή εσωτερικών βλαβών.

! Οι συσκευασίες δεν είναι παιχνίδια για μικρά

παιδιά!

Αλφάδιασμα

1. Τοποθετήστε το

πλυντήριο σε ένα

δάπεδο επίπεδο και

ανθεκτικό, χωρίς να

το ακουμπήσετε σε

τοίχους ή έπιπλα.

2. Αντισταθμίστε

τις ανωμαλίες

ξεβιδώνοντας ή

βιδώνοντας τα

ποδαράκια έως ότου η μηχανή αλφαδιαστεί

(δεν πρέπει να κλίνει περισσότερο από 2

μοίρες).

! Ένα επιμελές αλφάδιασμα δίνει

σταθερότητα και αποσοβεί δονήσεις και

θορυβότητα κυρίως στη φάση στυψίματος.

! Σε περίπτωση μοκέτας ή τάπητα, ρυθμίστε

τα ποδαράκια έτσι ώστε να υφίσταται κάτω

από το πλυντήριο αρκετός χώρος για τον

αερισμό.

Υδραυλικές και ηλεκτρικές

συνδέσεις

Σύνδεση του σωλήνα τροφοδοσίας του

νερού

! Πριν συνδέσετε το σωλήνα τροφοδοσίας στο

δίκτυο ύδρευσης, αφήστε να τρέξει το νερό

μέχρι να βγει διαυγές.

1. Συνδέστε το

σωλήνα τροφοδοσίας

στο πλυντήριο

βιδώνοντάς τον στην

αντίστοιχη είσοδο

νερού, στο πίσω

μέρος επάνω δεξιά

(βλέπε εικόνα).

2. Συνδέστε το

σωλήνα τροφοδοσίας

βιδώνοντάς τον σε

ένα κρουνό κρύου

νερού με στόμιο

σπειρώματος 3/4 gas

(βλέπε εικόνα).

3. Προσέξτε ώστε στο σωλήνα να μην

υπάρχουν ούτε πτυχώσεις, ούτε στενώσεις.

! Η πίεση νερού του κρουνού πρέπει να

κυμαίνεται μεταξύ των τιμών του πίνακα

Τεχνικά στοιχεία (βλέπε σελίδα δίπλα).

! Αν το μήκος του σωλήνα τροφοδοσίας δεν

επαρκεί, απευθυνθείτε σε ένα ειδικευμένο

κατάστημα ή σε εξουσιοδοτημένο τεχνικό.

! Μη χρησιμοποιείτε ποτέ χρησιμοποιημένους

ή παλιούς σωλήνες τροφοδοσίας, αλλά

εκείνους που παρέχονται με τη μηχανή.

Ôå÷íéêÜ óôïé÷åßá

ÌïíôÝëï ADS93D 69

ÄéáóôÜóåéò

ðëÜôïò cm 59,5

ýøïò cm 85

âÜèïò cm 64,5

×ùñçôéêüôçôá áðü 1 Ýùò 9 kg

ÇëåêôñéêÝò

óõíäÝóåéò

ÂëÝðå ôçí ðéíáêßäá

÷áñáêôçñéóôéêþí åðß ôçò

ìç÷áíÞò

ÓõíäÝóåéò

íåñïý

ìÝãéóôç ðßåóç

1 MPa (10 bar)

ÅëÜ÷éóôç ðßåóç

0,05 MPa (0,5 bar)

÷ùñçôéêüôçôá ôïõ êÜäïõ 62 ëßôñá

Ôá÷ýôçôá

óôõøßìáôïò

ìÝ÷ñé 1600 óôñïöÝò ôï

ëåðôü

Προγράμματα

ελέγχου

σύμφωνα με

τις οδηγίες

1061/2010

και

1015/2010

ðñüãñáììá

;

ΒΑΜΒΑΚΕΡΑ ΚΑΝΟΝΙΚΌ

60°C.

ðñüãñáììá

;

ΒΑΜΒΑΚΕΡΑ ΚΑΝΟΝΙΚΌ

40°C.

Ç óõóêåõÞ áõôÞ

åßíáé óýìöùíç ìå ôéò

áêüëïõèåò ÊïéíïôéêÝò

Ïäçãßåò:

- 2004/108/CE

(ÇëåêôñïìáãíçôéêÞ

Óõìâáôüôçôá)

- 2012/19/EU

- 2006/95/CE (×áìçëÞ ÔÜóç)

Σύνδεση του σωλήνα αποστράγγισης

Συνδέστε το σωλήνα

αδειάσματος σε

μια σωλήνωση

αδειάσματος ή

σε μια επιτοίχια

παροχέτευση σε

ύψος από το έδαφος

μεταξύ 65 και 100 cm

και αποφεύγοντας

ρητά να τον

διπλώσετε.

Εναλλακτικά,

στηρίξτε το σωλήνα

αδειάσματος στο

χείλος ενός νιπτήρα

ή μιας λεκάνης,

δένοντας τον οδηγό

που σας παρέχεται

στον κρουνό (βλέπε

εικόνα). Το ελεύθερο

άκρο του σωλήνα

αδειάσματος δεν

πρέπει να παραμένει βυθισμένο στο νερό.

! Δεν συνιστάται η χρήση προεκτάσεων

σωλήνων. Αν απαιτείται, η προέκταση πρέπει

να έχει την ίδια διάμετρο του αρχικού σωλήνα

και να μην ξεπερνάει τα 150 cm.

Ηλεκτρική σύνδεση

Πριν εισάγετε το βύσμα στην ηλεκτρική πρίζα,

βεβαιωθείτε ότι:

• η πρίζα διαθέτει γείωση και τηρεί τις εκ του

νόμου προδιαγραφές.

• Η πρίζα να είναι σε θέση να υποφέρει

το μέγιστο φορτίο ισχύος της μηχανής,

που αναφέρεται στον πίνακα Τεχνικών

στοιχείων (βλέπε δίπλα).

• Η τάση τροφοδοσίας να κυμαίνεται μεταξύ

των τιμών που αναφέρονται στον πίνακα

Τεχνικών στοιχείων (βλέπε δίπλα).

• Η πρίζα να είναι συμβατή με το βύσμα

της μηχανής. Σε αντίθετη περίπτωση,

αντικαταστήστε την πρίζα ή το βύσμα.

! Το πλυντήριο δεν εγκαθίσταται σε

ανοιχτό χώρο, ακόμη και αν ο χώρος είναι

καλυμμένος, διότι είναι πολύ επικίνδυνο να το

αφήνετε εκτεθειμένο σε βροχή και κακοκαιρία.

! Με την εγκατάσταση του πλυντηρίου, η πρίζα

ρεύματος πρέπει να είναι εύκολα προσβάσιμη.

! Μη χρησιμοποιείτε προεκτάσεις και

πολύπριζα.

! Το καλώδιο δεν πρέπει να φέρει πτυχές ή

να είναι συμπιεσμένο.

! Το καλώδιο τροφοδοσίας και το βύσμα

πρέπει να αντικαθίστανται μόνο από

εξουσιοδοτημένους τεχνικούς.

Προσοχή! Η επιχείρηση αποποιείται κάθε

ευθύνης σε περίπτωση που δεν τηρούνται

αυτοί οι κανόνες.

65 - 100 cm

αντικείμενα (κέρματα, κουμπιά) στον

προθάλαμο που προστατεύει την αντλία, που

βρίσκεται στο κάτω μέρος αυτής.

! Βεβαιωθείτε ότι ο κύκλος πλυσίματος έχει

τελειώσει και βγάλτε το βύσμα.

Για να έχετε πρόσβαση στον προθάλαμο:

1. αφαιρέστε το πάνελ κάλυψης στο πρόσθιο

πλευρό της μηχανής προς το κέντρο, κατόπιν

ωθήστε προς τα κάτω αμφότερα τα πλευρά

και βγάλτε το (βλέπε εικόνες).

2. τοποθετήστε ένα

δοχείο για τη συλλογή

του νερού που θα βγει

(περίπου 1,5 lt) (βλέπε

εικόνα).

3. Ξεβιδώστε το

καπάκι στρέφοντάς

το αριστερόστροφα

(βλέπε εικόνα).

4. καθαρίστε επιμελώς το εσωτερικό;

5. ξαναβιδώστε το καπάκι

6. ξαναμοντάρετε το πάνελ όντας σίγουροι,

πριν το σπρώξετε προς τη μηχανή, ότι έχετε

εισάγει τα γαντζάκια στις αντίστοιχες εσοχές.

Έλεγχος του σωλήνα τροφοδοσίας

του νερού

Ελέγχετε το σωλήνα τροφοδοσίας

τουλάχιστον μια φορά ετησίως. Αν

παρουσιάζει σκασίματα και σχισμές

αντικαθίσταται: κατά τα πλυσίματα οι ισχυρές

πιέσεις θα μπορούσαν να προκαλέσουν

αναπάντεχα σπασίματα.

Αποκλεισμός νερού και ηλεκτρικού

ρεύματος

• Κλείστε τον κρουνό του νερού μετά από

κάθε

πλύσιμο. Έτσι περιορίζεται η φθορά της

υδραυλικής εγκατάστασης της μηχανής και

αποσοβείται ο κίνδυνος απωλειών.

• Να βγάζετε το βύσμα από το ρεύμα όταν

καθαρίζετε το μηχάνημα και κατά τις

εργασίες συντήρησης.

Καθαρισμός της μηχανής

Το εξωτερικό μέρος και τα λαστιχένια μέρη

μπορούν να καθαρίζονται με ένα πανί

βρεγμένο με χλιαρό νερό και σαπούνι. Μη

χρησιμοποιείτε διαλύτες ή αποξυστικά.

Καθαρισμός του συρταριού

απορρυπαντικών

Για να βγάλετε το συρτάρι, ανοίξτε το μέχρι

το πρώτο στοπ, μετά πατήστε το μοχλό A

ανοίγοντάς τον τελείως, τέλος πατήστε έναν

από τους μοχλούς D και τραβήξτε τον προς

τα έξω (βλέπε εικόνες).

Πλένετέ το κάτω από τρεχούμενο νερό.

Ο καθαρισμός αυτός διενεργείται συχνά.

Μεριμνήστε να απομακρύνετε και ενδεχόμενα

υπολείμματα απορρυπαντικών από την έδρα

του συρταριού στη μηχανή.

Για να το ξαναμοντάρετε πρέπει να το

κρατάτε πλευρισμένο τελείως αριστερά,

προσέχοντας να κεντράρετε τον οδηγό

ολίσθησης και να αποτρέψετε την εμπλοκή.

Φροντίδα του κάδου

• Να αφήνετε πάντα μισόκλειστη την πόρτα

για να μην παράγονται δυσοσμίες.

Καθαρισμός της αντλίας

Το πλυντήριο διαθέτει μια αυτοκαθαριζόμενη

αντλία που δεν χρειάζεται συντήρηση.

Μπορεί, όμως, να τύχει να πέσουν μικρά

Συντήρηση και φροντίδα

Sayfa yükleniyor ...

HOTPOINT/ARISTON ADS93D 69 EU/B Kullanici rehberi

Marka: HOTPOINT/ARISTON

Model: ADS93D 69 EU/B

Kategori: Çamaşır makineleri

Tip: Kullanici rehberi

PDF İndir

rapor

HOTPOINT/ARISTON ADS93D 69 EU/B Kullanici rehberi

HOTPOINT/ARISTON ADS93D 69 EU/B Kullanici rehberi

İlgili Makaleler

Diğer Belgeler