Regal RTV 19916 Operating Instructions Manual

Marka: Regal

Model: RTV 19916

Kategori: LCD TV'ler

Tip: Operating Instructions Manual

RTV 19" 19916 LED TV

OPERATING INSTRUCTIONS

KULLANIM KILAVUZU

OPERATING INSTRUCTIONS

KULLANIM KILAVUZU

50191891

RRR

www.regal-tr.com 444 4 789

Cihazın Sanayi Bakanlığı tarafından tespit ve ilan edilen kullanım ömrü (cihazın

fonksiyonlarını yerine getirebilmesi için gerekli yedek parça bulundurma süresi) 10 yıldır.

English - 1 -

Contents

Features ................................................................. 2

Introduction ............................................................. 2

Preparation ............................................................. 2

Safety Precautions ................................................. 3

Connection to a Television Distribution

System (Cable TV etc.) from Tuner .................... 4

Package Contents .................................................. 4

Environmental Information ..................................... 5

Repair Information .............................................. 5

Remote Control Buttons ......................................... 6

LED TV and Operating Buttons .............................. 7

Viewing the Back side Connections ....................... 7

Viewing the Connections - Side Connectors .......... 8

Power Connection .................................................. 8

Aerial Connection ............................................... 8

Using Digital Multimedia Connectors...................... 9

USB Memory Connection ................................... 9

Connecting the LED TV to a PC ............................. 9

Using Side AV Connectors ..................................... 9

Connecting to a DVD Player via HDMI ................... 9

Connecting to a DVD Player via Component

Sockets (YPbPr) or Scart Cable ........................... 10

Remote Control Handset ...................................... 10

Inserting Batteries ............................................. 10

Switching On/Off ................................................... 10

To Switch the TV On ......................................... 10

To Switch the TV Off ......................................... 10

Input Selection .......................................................11

Basic Operations ...................................................11

Operation with the Buttons of the TV .................11

Volume Setting ...............................................11

Programme Selection ....................................11

AV Mode ........................................................11

Operation with the Remote Control ...................11

Volume Setting ...............................................11

Programme Selection

(Previous or Next Programme) ......................11

Programme Selection (Direct Access) ...........11

Viewing Electronic Programme Guide (EPG) ........11

First Time Installation............................................ 12

Installation ............................................................ 13

Automatic Channel Scan

(Retune) Menu Operation ................................. 13

Manual Tuning ..................................................... 14

Digital Manual Search....................................... 14

Analogue Manual Search ................................. 14

Analogue Fine Tune.......................................... 14

Clear Service List (*) ......................................... 14

Managing Stations: Channel List .......................... 14

Operating the Channel List ............................... 15

Moving a Channel ............................................. 15

Deleting a Channel ........................................... 15

Renaming a Channel ........................................ 15

Locking a Channel ............................................ 15

Managing Stations: Favourites ............................. 15

Button Functions ............................................... 15

Managing Stations: Sorting Channel List ............. 16

On-Screen Information ......................................... 16

Media Playback Using Media Browser ................. 16

Viewing Photos via USB ................................... 17

Media Browser Settings .................................... 18

Changing Image Size: Picture Formats ................ 18

Conﬁ guring Picture Settings ................................. 19

Operating Picture Settings Menu Items ............ 19

Picture Settings Menu Items ............................. 19

PC Picture Settings........................................... 20

Conﬁ guring Sound Settings .................................. 20

Operating Sound Settings Menu Items ............. 20

Sound Settings Menu Items.............................. 20

Conﬁ guring Your TV’s Settings ............................. 21

Operating Settings Menu Items ........................ 21

Settings Menu Items ......................................... 21

Using a Conditional Access Module ..................... 21

Viewing Conditional Access Menu (*) ............... 21

Conﬁ guring Language Preferences ...................... 22

Language Settings ............................................ 22

Parental Control.................................................... 23

Parental Settings Menu Operation ................... 23

Timers ................................................................... 23

Setting Sleep Timer .......................................... 23

Setting Programme Timers ............................... 23

Adding a Timer .............................................. 23

Editing a Timer .............................................. 23

Deleting a Timer ............................................ 24

Conﬁ guring Date/Time Settings ............................ 24

Conﬁ guring Source Settings ................................. 24

Conﬁ guring Other Settings ................................... 25

Operation .......................................................... 25

Other Features ..................................................... 25

Teletext ................................................................. 26

Tips ....................................................................... 26

Appendix A: PC Input Typical Display Modes ....... 27

Appendix B: AV and HDMI Signal

Compatibility (Input Signal Types) ........................ 27

Appendix C: Supported DVI Resolutions.............. 28

Appendix D: Supported File Formats

for USB Mode ....................................................... 28

Appendix E: Software Upgrade ............................ 29

Speciﬁ cations ....................................................... 30

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 101_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1 13.05.2011 13:04:1413.05.2011 13:04:14

English - 2 -

Features

Remote controlled colour LED TV.•

Fully integrated Terrestrial digital TV (DVB-T - MPEG2) •

HDMI connectors for digital video and audio. This •

connection is also designed to accept high deﬁ nition

signals.

USB input.•

1000 programmes (analogue+digital).•

OSD menu system.•

Integrated tuner MPEG2 compatible.•

Scart socket for external devices (such as video, •

video games, audio set, etc.).

Stereo sound system. (German+Nicam)•

Teletext, fastext, TOP text.•

Headphone connection.•

Automatic programming system.•

Forward or backward manual tuning.•

Sleep timer / Child lock.•

Automatic sound mute when no transmission.•

NTSC playback. •

AVL (Automatic Volume Limiting).•

Auto power down.•

PLL (Frequency Search).•

PC input. •

Plug&Play for Windows 98, ME, 2000, XP, Vista, •

Windows 7.

Game Mode •

Introduction

Please read the corresponding instructions of this

handbook prior to the ﬁ rst usage of the device, even

when the usage of electronic devices is familiar

to you. Notice especially the chapter SAFETY

PRECAUTIONS. Carefully keep the handbook as

future reference. When selling the device or giving it

away, absolutely give these direction for use.

Thank you for choosing this product. This manual will

guide you for the proper operation of your TV.

Before operating the TV, please read this

manual thoroughly. Please do keep this

manual in a safe place for future references.

This device is intended to receive and display TV

programs. The different connection options make

an additional expansion of the reception and display

sources possible (receiver, DVD player, DVD

recorder,

VCR, PC etc.). This device is only suitable for the

operation in dry interiors. This appliance is intended

solely for private domestic use and may not be used

for industrial and commercial purposes. We exclude

liability in principle, if the device is not used as

intended, or unauthorized modiﬁ cations have been

made. To operate your LED TV in extreme ambient

conditions may cause the damage of the device.

Preparation

For ventilation, leave a free space of at least 10 cm

all around the set. To prevent any fault and unsafe

situations, please do not place any objects on top of

the set. Use this device in moderate climates.

10 cm

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 201_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 2 13.05.2011 13:04:1413.05.2011 13:04:14

English - 3 -

Safety Precautions

Read the following recommended safety

precautions carefully for your safety.

Power Source

The TV set should be operated only from a 220-240V

AC, 50 Hz outlet. Ensure that you select the correct

voltage setting for your convenience.

Power Cord

Do not place the set, a piece of furniture, etc. on the

power cord (mains lead) or pinch the cord. Handle the

power cord by the plug. Do not unplug the appliance

by pulling from the power cord and never touch the

power cord with wet hands as this could cause a short

circuit or electric shock. Never make a knot in the cord

or tie it with other cords. The power cords should be

placed in such a way that they are not likely to be

stepped on. A damaged power cord can cause ﬁ re or

give you an electric shock. When it is damaged and

needs to be replaced, it should be done by qualiﬁ ed

personnel.

Moisture and Water

Do not use this device in a humid and

damp place (avoid the bathroom, the

sink in the kitchen, and near the washing

machine). Do not expose this device to

rain or water, as this may be dangerous

and do not place objects filled with

liquids, such as ﬂ ower vases, on top.

Avoid from dripping or splashing.

If any solid object or liquid falls into the cabinet, unplug

the TV and have it checked by qualiﬁ ed personnel

before operating it any further.

Cleaning

Before cleaning, unplug the TV set

from the wall outlet. Do not use liquid

or aerosol cleaners. Use soft and dry

cloth.

Ventilation

The slots and openings on the TV set are intended for

ventilation and to ensure reliable operation. To prevent

overheating, these openings must not be blocked or

covered in anyway.

Heat and Flames

The set should not be placed near to

open ﬂ ames and sources of intense heat

such as an electric heater. Ensure that

no open ﬂ ame sources, such as lighted

candles, are placed on top of the TV. Batteries should

not be exposed to excessive heat such as sunshine,

ﬁ re or the like.

Lightning

In case of storm and lightning or when

going on holiday, disconnect the power

cord from the wall outlet.

Replacement Parts

When replacement parts are required, make sure that

the service technician has used replacement parts,

which are speciﬁ ed by the manufacturer or have the

same speciﬁ cations as the original one. Unauthorized

substitutions may result in ﬁ re, electrical shock or

other hazards.

Servicing

Please refer all servicing to qualiﬁ ed

personnel. Do not remove the cover

yourself as this may result in an electric

shock.

Waste Disposal

Instructions for waste disposal:•

Packaging and packaging aids are recyclable and

should principally be recycled. Packaging materials,

such as foil bag, must be kept away from children.

Batteries, including those which are heavy metal-free,

should not be disposed of with household waste.

Please dispose of used battery in an environment

friendly manner. Find out about the legal regulations

which apply in your area.

Don’t try to recharge batteries. Danger of explosion. •

Replace batteries only with the same or equivalent

type.

Disconnecting the Device

The mains plug is used to disconnect TV set from

the mains and therefore it must remain readily

operable.

Headphone Volume

Excessive sound pressure from earphones

and headphones can cause hearing loss.

Installation

To prevent injury, this device must be securely

attached to the wall in accordance with the installation

instructions when mounted to the wall (if the option

is available).

LED Screen

The LED panel is a very high technology product with

about a million thin ﬁ lm transistors, giving you ﬁ ne

picture details. Occasionally, a few non-active pixels

may appear on the screen as a ﬁ xed blue, green or

red point. Please note that this does not affect the

performance of your product.

Warning! Do not leave your TV in standby or operating

mode when you leave your house.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 301_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 3 13.05.2011 13:04:1513.05.2011 13:04:15

English - 4 -

The Standby Off/On button doesn´t separate this

device completely from mains. Moreover the device

consumes power in the standby operation. In order to

separate the device completely from mains, the mains

plug has to be pulled from the mains socket. Because

of that the device should be set up in a way, that an

unobstructed access to mains socket is guaranteed,

so that in case of emergency the mains plug can be

pulled immediately. To exclude the danger of ﬁ re, the

power cord should principally be separated from the

mains socket prior to a longer period of non-usage,

i.e. during vacations.

Electrical device not in the hands of children

Never let children use electrical device unsupervised.

Children can´t always recognize properly the

possible dangers. Batteries / accumulators can be

life threatening when swallowed. Store batteries

unreachable for small children. In case of swallowing

a battery medical aid has to be sought immediately.

Also keep the packaging foils away from children.

There is danger of suffocation.

Licence Notiﬁ cation (optional)

Manufactured under license from Dolby

Laboratories.

TRADEMARK ACKNOWLEDGMENT

“Dolby” and the double-D symbol are trademarks of

Dolby Laboratories.

Connection to a Television Distribution

System (Cable TV etc.) from Tuner

Device connected to the protective earthing of the

building installation through the mains connection or

through other apparatus with a connection to protective

earthing-and to a television distribution system using

coaxial cable, may in some circumstances create a

ﬁ re hazard.

Connection to a cable distribution system has

therefore to be provided through a device providing

electrical isolation below a certain frequency range

(galvanic isolator, see EN 60728-11).

Package Contents

SLEEP

SCREEN LANG. SUBTITLE

ABC

DEF

GHI

JKL

MNO PQR

STU

VWX YZ

RETURN

INFO

FAV

SOURCE PRESETS

EPG

Remote Control

LED TV

Batteries: 2 X AAA

Instruction Book

1 X Video & Audio Connection Cable

Note: You should check the accessories after

purchasing. Make sure that each accessory is

included.

Note: The HDMI connection between PC and TV

may cause radio interference in which case it is

recommended to use VGA(DSUB-15) connection.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 401_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 4 13.05.2011 13:04:1513.05.2011 13:04:15

English - 5 -

Environmental Information

This television is designed to consume less energy to save environment. •

You not only help to save the environment but also you can save money by reducing electricity bills thanks to the

energy efﬁ ciency feauture of this TV. To reduce energy consumption, you should take the following steps:

You can use Power Save Mode setting, located in the Feature menu. If you set Power Save Mode as On, •

the TV will switch to energy-saving mode and luminance level of TV set will be decreased to optimum level.

Note that some picture settings will be unavailable to be changed when the TV is in Power Save Mode.

When the TV is not in use, please switch off or disconnect the TV from the mains plug. This will also reduce •

energy consumption.

Disconnect power when going away for longer time.•

Note that annually, using the TV set in Power Save Mode has more power efﬁ ciency than disconnecting •

the TV from the mains plug instead of keeping stand-by mode. Therefore disconnect the TV from the mains

plug to save energy when you do not use. However it is highly recommended to activate Power Save Mode

setting to reduce your annual power consumption.

Please helps us to save environment by following these steps.•

Repair Information

Please refer all servicing to qualiﬁ ed personnel. Only qualiﬁ ed personnel must repair the TV. Please contact

your local dealer, where you have purchased this TV for further information.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 501_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 5 13.05.2011 13:04:1713.05.2011 13:04:17

English - 6 -

Remote Control Buttons

SLEEP

SCREEN LANG. SUBTITLE

ABC

DEF

GHI

JKL

MNO PQR

STU

VWX YZ

RETURN

INFO

FAV

SOURCE PRESETS

EPG

Standby1.

Yellow button2.

Blue button3.

Return / Exit menu / Index Page (in TXT mode)4.

Navigation buttons5.

OK / Channel list6.

Picture mode selection7.

EPG (Programme Guide)8.

Programme Up / Down9.

Numeric buttons10.

Previous programme11.

Subtitle on/off12.

Sleep timer13.

Teletext / Mix14.

No function 15.

Green button16.

Red button17.

Menu On/Off18.

AV / Source19.

Info20.

Volume Up/Down21.

Mute22.

Favourite mode23.

Mono-Stereo / Dual I-II24.

Image Size25.

Media Browser26.

No function27.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 601_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 6 13.05.2011 13:04:1713.05.2011 13:04:17

English - 7 -

LED TV and Operating Buttons

FRONT and REAR VIEW Control buttons VIEW Control Buttons

P\V-AV

1. Standby Off/On button

2. TV/AV button

3. Programme Up/Down buttons-

Volume Up/Down buttons

Note:You can use +/- buttons

to change volume. If you want

to change channels, press P/V/

AV button once and then use

+/- buttons. If you hold the P/V/

AV button about a few seconds,

source OSD will be displayed.

Main menu OSD cannot be

displayed via control buttons.

Viewing the Back side Connections

I 1

SPDIF

Coax.OUT

HDMI 1: HDMI Input1.

HDMI Inputs are for connecting a device that has an HDMI socket. Your LED TV is capable of

displaying High Deﬁ nition pictures from devices such as a High Deﬁ nition Satellite Receiver or DVD

Player. These devices must be connected via the HDMI sockets or Component Socket. These sockets

can accept either 720p or 1080p signals. No sound connection is needed for an HDMI to HDMI

connection.

RF Input2. connects to an aerial antenna system.

Note that if you use a decoder or a media recorder, you should connect the aerial cable through the device

to the television with an appropriate antenna cable, as shown in the illustration in the following pages.

SCART3. input or output for external devices. Connect the SCART cable between SCART socket on TV and

SCART socket on your external device (such as a decoder, a VCR or a DVD player).

Note: If an external device is connected via the SCART socket, the TV will automatically switch to AV mode.

PC Input4. is for connecting a personal computer to the TV set.

Connect the PC cable between the PC INPUT on the TV and the PC output on your PC.

Note: You can use YPbPr to VGA cable(not supplied) to enable YPbPr signal via PC input.

S/PDIF Coaxial Out5. outputs digital audio signals of the currently watched source.

Use an SPDIF coaxial cable to trasfer audio signals to a device that has S/PDIF input.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 701_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 7 13.05.2011 13:04:1713.05.2011 13:04:17

English - 8 -

Viewing the Connections - Side Connectors

CI Slot is used for inserting a CI card. A CI card allows you to view all the channels that 1.

you subscribe to. For more information, see “Conditional Access” section.

Side USB input.2.

TV control buttons.3.

Side audio-video connection4. input is used for connecting video and audio signals

of external devices. To make a video connection, you must use the supplied AV

connection cable for enabling connection. First, plug singular jack of the cable to the

TV’s Side AV socket. Afterwards, insert your video cable’s (not supplied) connector into

the YELLOW input (located on the plural side) of the supplied AV connection cable.

Colours of the connected jacks should match.

To enable audio connection, you must use RED and WHITE inputs of the side AV

connection cable. Afterwards, insert your device’s audio cable’s connectors into

the RED and WHITE jack of the supplied side AV connection cable. Colours of the

connected jacks should match.

Note: You should use audio inputs of side AV connection cable (RED & WHITE)

to enable sound connection when connecting a device to your TV by using PC or

COMPONENT VIDEO input.

Headphone jack is used for connecting an external headphone to the system. Connect 5.

to the HEADPHONE jack to listen to the TV from headphones (optional).

Power Connection

IMPORTANT: The TV set is designed to operate on 220-240V AC, 50 Hz.

After unpacking, allow the TV set to reach the ambient room temperature before you connect the set to the •

mains. Plug the power cable to the mains socket outlet.

Aerial Connection

Connect the aerial ,cable TV plug to the AERIAL INPUT socket located at the rear of the TV.•

DMI

SPDIF

Coax.OUT

USB

5Vdc

Max:500mA

P\V-AV

SIDE AV

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 801_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 8 13.05.2011 13:04:1913.05.2011 13:04:19

English - 9 -

Using Digital Multimedia

Connectors

You can connect USB devices to your TV by using •

the USB input of the TV. This feature allows you to

display/play JPG, MP3 and video ﬁ les stored in a

USB stick.

It is possible that certain types of USB devices (e.g. •

MP3 Players) may not be compatible with this TV.

You may back up your ﬁ les before making any •

connections to the TV set in order to avoid any

possible data loss. Note that manufacturer will not

be responsible for any ﬁ le damage or data loss.

Do not pull out USB module while playing a ﬁ le.•

CAUTION: Quickly plugging and unplugging USB

devices, is a very hazardous operation. Especially,

do not repeatedly quickly plug and unplug the

drive. This may cause physical damage to the USB

player and especially the USB device itself.

SIDE VIEW USB MEMORY

5Vdc

Max:500mA

USB

USB Memory Connection

IMPORTANT: The TV should be switched off while

plugging or unplugging a USB device. Plug your

USB devices to the USB input of the TV. You can

connect a usb device to your TV by using the USB

input of the TV.

Note: It is possible certain types of hard disk drives

are not supported.

Connecting the LED TV to a PC

For displaying your computer’s screen image on your

LED TV, you can connect your computer to the TV set.

Power off both computer and display before making

any connections. Use 15-pin D-sub display cable to

connect a PC to the LED TV. When the connection

is made, switch to PC source. See “Input selection”

section. Set the resolution that suits your viewing

requirements. Resolution information can be found

in the appendix parts.

PC Input

(back)

Side AV Input

PC VGA Cable

(Not supplied)

PC Audio Cable

(Not supplied)

Side Audio/Video

Connection Cable

(Supplied)

SIDE AV

Using Side AV Connectors

You can connect a range of optional equipment to your

LED TV using side connectors of the TV.

For connecting a camcorder or camera , you should •

use AV socket (side). To do this, you must use the

supplied video/audio connection cable. First, plug

single jack of the cable to the TV’s AV IN socket

(side). Afterwards, insert your camera cable’s (not

supplied) connectors into the plural part of the video/

audio connection cable. Colours of the connected

jacks should match. See illustration below.

Afterwards, you should switch to • Side AV source. See

the section Input selection in the following sections

for more information.

Camera

AV Connection

Cable (supplied)

AV Cable

(not supplied)

Headphone

SIDE AV

To listen the TV sound from headphones, you •

should connect headphones to your TV by using the

HEADPHONE jack as illustrated above.

Connecting to a DVD Player via HDMI

Please refer to your DVD player’s instruction book

for additional information. Power off both the TV and

the device before making any connections.

Note: Not all cables shown in the illustration are

supplied.

If your DVD player has an • HDMI socket, you can

connect via HDMI for better video and audio quality.

HDMI

SPDIF

Coax.OUT

External device

(not supplied)

HDMI Cable

When you connect to DVD player as illustrated above, •

switch to the connected HDMI source. See, Input

Selection section for more information on changing

sources.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 901_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 9 13.05.2011 13:04:1913.05.2011 13:04:19

English - 10 -

Remote Control Handset

Inserting Batteries

Remove the battery cover located on the back of •

the handset by gently pulling backwards from the

indicated part.

Insert two • AAA/R3 or equivalent type batteries

inside. Observe the correct polarity (+/-) when

inserting batteries and replace the battery cover.

Note: Remove the battery from remote control

handset when it is not to be used for a long period.

Otherwise it can be damaged due to any leakage of

batteries. Remote range is approximately 7m/23ft.

Switching On/Off

To Switch the TV On

Connect the power cord to the 220-240V AC, 50 Hz. •

Then the standby LED lights up.(The led will blink

during the standby On/Off)

To switch on the TV from standby mode either:•

Press the “•

” button, P+ / P- or a numeric button

on the remote control.

Press the “•

” button, - or + button on the TV. The

TV will then switch on.

Note: If you switch on your TV via PROGRAMME

UP/DOWN buttons on the remote control or on the

TV set, the programme that you were watching last

will be reselected.

By either method the TV will switch on.

To Switch the TV Off

Press the “• ” button on the remote control or press

the “ ” switch on the TV, so the TV will switch to

standby mode.

To power down the TV completely, unplug the •

power cord from the mains socket.

Note: When the TV is switched to standby mode,

standby LED can blink to indicate that features such

as Standby Search, Over Air Download or Timer is

active.

Connecting to a DVD Player via

Component Sockets (YPbPr) or

Scart Cable

Some DVD players are connected through •

COMPONENT SOCKETS (YPbPr). YPbPr can be

used only when you connect a device that has a

YPbPr output through the PC input with YPbPr to

PC cable (YPbPr cable is not supplied).

When the connection is made, switch to YPbPr •

source. See, “Input selection” section.

To enable audio connection, use the • VGA/

Component Audio cable. First, plug single jack

of the cable to the TV. Afterwards, insert your DVD

player’s audio cable’s connectors into the plural part

of the VGA/Component audio connection cable

(see illustration below). Colours of the connected

jacks should match ( RED & WHITE).

AV Connection

Cable (supplied)

Audio Cable

(not supplied)

To DVD Player's

Audio Outputs.

SIDE AV

When the connection is made, switch to • YPbPr source.

See, Input selection section.

You may also connect through the • SCART input.

HDMI

SPDIF

Coax.OUT

Scart Cable

(not supplied)

External device

Note: These three methods of connection perform the

same function but in different levels of quality. It is not

necessary to connect by all three methods.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1001_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 10 13.05.2011 13:04:2013.05.2011 13:04:20

English - 11 -

Input Selection

Once you have connected external systems to

your TV, you can switch to different input sources.

Press “SOURCE” button on your remote control

consecutively for directly changing sources.

Note: YPbPr mode can be used only when you

connect a device that has a YPbPr output through the

PC input with YPbPr to PC cable (not supplied).

Basic Operations

You can operate your TV using both the remote

control and onset buttons.

Operation with the Buttons of the TV

Main menu OSD cannot be displayed via control

buttons. “+/-” buttons will function as volume up/down

as default. Even if you set other functions for these

buttons, “+/-” buttons will perform as default after a

short while.

Volume Setting

• Press “• +/-” buttons to increase or decrease volume,

so a volume level scale (slider) will be displayed on

the screen.

Programme Selection

• Press • P/V/AV button once and then use “+/-”

buttons to select the next or previous programme.

AV Mode

• Hold the “• P/V/AV” button, source OSD will be

displayed.

• Use “• +/-” buttons to select the desired source.

Operation with the Remote Control

The remote control of your TV is designed to control •

all the functions of the model you selected. The

functions will be described in accordance with the

menu system of your TV.

Volume Setting

Press “• V+” button to increase the volume. Press “V-”

button to decrease the volume. A volume level scale

(slider) will be displayed on the screen.

Programme Selection (Previous or Next

Programme)

Press “• P -” button to select the previous

programme.

Press “• P +” button to select the next programme.

Programme Selection (Direct Access)

Press numeric buttons on the remote control to select •

programmes between 0 and 9. The TV will switch

to the selected programme. To select programmes

between, press the numeric buttons consecutively.

When the pressing time is due for the second

numeric button, only the ﬁ rst digit programme will

be displayed. Press directly the programme number

to reselect single digit programmes.

Viewing Electronic Programme

Guide (EPG)

You can view the electronic programme guide (EPG)

to view information about available programmes.To

view the EPG menu please press EPG button on the

remote control.

Press “•

”/“ ” buttons to navigate through channels.

Press “•

”/“ ” buttons to navigate through the

programme list.

EPG menu displays available information on all •

channels.

Please note that event information is updated •

automatically. If there are no event information

data available for channels, EPG will be displayed

with blanks.

OK (Options): Displays programme options including

“Select Channel” option.

INFO (Event Details): Displays the programmes in

detail.

Green button: Programme schedule will be listed

Yellow button: Display EPG data in accordane with

timeline schedule

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1101_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 11 13.05.2011 13:04:2113.05.2011 13:04:21

English - 12 -

Blue button (Filter): Views ﬁ ltering options.

Red button (Prev Time Slice): Displays the

programmes of previous time slice.

Green button (Next Time Slice): Displays the

programmes of the next time slice.

Yellow button (Prev Day): Displays the programmes

of previous day.

Blue button (Next day): Displays the programmes

of the next day.

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK (Options): Displays programme options including

“Select Channel” option.

Text button (Filter): Views ﬁ ltering options.

INFO (Details): Displays the programmes in detail.

Red button (Prev Day): Displays the programmes

of previous day.

Green button (Next day): Displays the programmes

of the next day.

Yellow button (Zoom): Expands programme

information.

Blue button (Filter): Views ﬁ ltering options.

INFO (Details): Displays the programmes in detail.

Numeric buttons (Jump): Jumps to the preferred

channel directly via numeric buttons.

OK (Options): Displays programme options including

“Select Channel” option.

Text (Search): Displays “Guide Search” menu.

SUBTTL: Press SUBTITLE button to view Select

Genre menu. Using this feature, you can search the

programme guide database in accordance with the

genre. Info available in the programme guide will

be searched and results matching your criteria will

be listed.

(Now) : Shows the current programme.

First Time Installation

IMPORTANT: Ensure that the aerial is connected

before switching on the TV for the first time

installation.

When the TV is operated for the ﬁ rst time, installation •

wizard will guide you through the process. First,

language selection screen will be displayed:

Use “• ” or “ ” buttons to select your language

and press OK button to set selected language and

continue.

After selecting the language, “• Welcome!” screen will

be displayed, requiring you to set Country,Teletext

Language and Scan Encrypted options.

By pressing “• ” or “ ” button, select the country

you want to set and press “ ” button to highlight

Teletext Language option. Use “ ” or “ ” button

to select desired Teletext Language.

Press “•

” button after setting Teletext Language

option. Scan Encrypted will be then highlighted.

You can set Scan Encrypted as Yes if you want to

scan coded stations.Afterwards select the desired

Teletext Language.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1201_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 12 13.05.2011 13:04:2213.05.2011 13:04:22

English - 13 -

Press • OK button on the remote control to continue

and the following message will be displayed on the

screen:

To select the “Yes” or “No” option, highlight the item by

using “

” or “ ” buttons and press OK button.

Afterwards, the following OSD will be displayed on the

screen and the digital television will search for digital

terrestrial TV broadcasts

Note: You can press “M” button to cancel.

After all the available stations are stored, Channel •

List will be displayed on the screen. If you like the

sort channels, according to the LCN,please select

“Yes” and than press “OK”.

Press • OK button to quit channel list and watch TV.

Installation

Press “M” button on the remote control and select

Installation by using “

” or “ ” button. Press

OK button and the following menu screen will be

displayed.

Select Automatic Channel Scan (Retune) by using

“

”/“ ” button and press OK button. Automatic

Channel Scan (Retune) options will be displayed. You

can select Digital Aerial, Analogue or Digital Aerial-

Analogue tuning using “ ”/“ ” and OK buttons.

Automatic Channel Scan (Retune) Menu

Operation

Digital: Searches and stores aerial DVB stations.

Analogue: Searches and stores analogue stations.

Full: Searches and stores both analogue and aerial

DVB stations.

Whenever you select an automatic search type and •

press OK button, a conﬁ rmation screen will appear

on the screen. To start installation process, select

Yes, to cancel select No by using .“ ” or “ ” and

OK button.

After auto channel scan type is set and selected •

and conﬁ rmed, installation process will start and

progress bar will move along. Press “M” button to

cancel process. In such a case, located channels

are not stored.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1301_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 13 13.05.2011 13:04:2313.05.2011 13:04:23

English - 14 -

Manual Tuning

HINT: This feature can be used for direct broadcast

entry.

Select • Manual Channel Scan from the Installation

menu by using “

”/“ ” and OK buttons. Manual

Scan options screen will be displayed.

Select the desired • Search Type using “

” or “

” button. Manual search options will change

accordingly. Use “

”/“ ” button to highlight an item

and then press “

” or “ ” button to set an option.

You can press “M” button to cancel.

Digital Manual Search

In manual channel scan, the number of the multiplex

or frequency are entered manually and only that

multiplex or frequency are searched for the channels.

After selecting search type as Digital, you can enter

the multiplex or frequency number using the numeric

buttons and press OK button to search.

Analogue Manual Search

After selecting search type as analogue, you can use

“ ”/“ ” button to highlight an item and then press “

” or “ ” button to set an option.

Enter the channel number or frequency using the

numeric buttons. You can then press OK button

to search. When the channel is located, any new

channels that are not on the list will be stored.

Analogue Fine Tune

Select • Analogue Fine Tune from the Installation

menu by using “ ” or “ ” and OK buttons. Analogue

ﬁ ne tune screen will be displayed. Analogue Fine

Tune feature will not be available if there are no

analogue channels, digital channels and external

sources stored.

Press • OK button to proceed. Use “

” or “ ” button

to set Fine Tune. When ﬁ nished, press OK button

again.

Clear Service List (*)

(*) This setting is visible only when the Country option

is set to Denmark, Sweden, Norway or Finland.

Use this setting to clear channels stored. Press “

” or

“

” button to select Clear Service List and then press

OK. The following OSD message will be displayed

on the screen:

Press OK to cancel. Select Yes by pressing “ ” or “ ”

button and press OK to delete all of the channels.

Managing Stations: Channel List

The TV sorts all stored stations in the Channel List.

You can edit this channel list, set favourites or set

active stations to be listed by using the Channel List

options.

Press • “M” button to view main menu. Select

Channel List item by using “

” or “ ” button. Press

OK to view menu contents.

Select Edit Channel List to manage all stored

channels. Use “ ” or “ ” and OK buttons to select

Edit Channel List.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1401_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 14 13.05.2011 13:04:2413.05.2011 13:04:24

English - 15 -

Operating the Channel List

Press “• ” or “ ” button to select the channel that

will be processed. Press “

” or “ ” button to select

a function on Channel List menu.

Use • P+/P- buttons to move page up or down.

Press • BLUE button to view ﬁ ltering options.

Press • “M” button to exit.

Moving a Channel

First select the desired channel. Select Move option •

in the channel list and press OK button.

Edit Number screen will be displayed. Enter the •

desired channel number by using the numeric

buttons on the remote control. If there is a previously

stored channel on that number, a warning screen

will be displayed. Select Yes if you want to move the

channel and press OK.

Press • OK button to process. Selected channel is

now moved.

Deleting a Channel

You can press GREEN button to tag/untag all

channels; YELLOW button to tag/untag channel.

Select the channel that you want to delete and select •

Delete option. Press OK button to continue.

A warning screen will appear. Select • YES to delete,

select No to cancel. Press OK button to continue.

Renaming a Channel

Select the channel that you want to rename and •

select Edit Name option. Press OK button to

continue.

Pressing “•

” or “ ” button moves to the previous/

next character. Pressing “ ” or “ ” button toggles

the current character, i.e., ‘b’ character becomes ‘a’

by “ ” and ‘c’ by “ ”. Pressing the numeric buttons

‘0...9’ replaces the highlighted character with the

characters printed above the button one by one as

the button is pressed.

When ﬁ nished, press • OK button to save. Press

“M” to cancel.

Locking a Channel

You can press GREEN button to tag/untag all

channels; YELLOW button to tag/untag a single

channel.

Select the channel that you want to lock and select •

Lock option. Press OK button to continue.

You will be asked to enter parental control PIN. •

Default PIN is set as 0000. Enter the PIN number.

Press • OK button when the desired channel is

highlighted to lock/unlock the channel. Lock symbol

will be displayed next to the selected channel.

Managing Stations: Favourites

You can create a list of favourite programmes.

Press • “M” button to view main menu. Select

Channel List item by using “

” or “ ” button. Press

OK to view menu contents.

Select • Favourites to manage favourite list. Use “

”/“ ” and OK buttons to select Favourites.

You can set various channels as favourites so that •

only the favourite channels are navigated.

Select a channel by using “• ” or “ ” button. Press

OK button to add selected channel to favourites list.

Press OK button again to remove.

Button Functions

OK• : Add/remove a station.

YELLOW• : Tag/untag a channel.

GREEN• : Tag/untag all channels.

BLUE• : Displays ﬁ ltering options.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1501_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 15 13.05.2011 13:04:2513.05.2011 13:04:25

English - 16 -

Managing Stations: Sorting

Channel List

You can select broadcasts to be listed in the channel

list. To display speciﬁ c types of broadcast, you should

use Active channel list setting.

Select Active channel list from the Channel list

menu by using “

” or “ ” button. Press OK button

to continue.

You can select a broadcast type option from the list

by using “

” /“ ” and OK buttons.

On-Screen Information

You can press “INFO” button to display on-screen

information. Details of the station and current

programme will be displayed on the information

banner.

The information banner gives information on the

channel selected and the programmes on it. The

name of the channel is displayed, along with its

channel list number. Hint: Not all channels broadcast

the programme data. If the name and time of the

programme are not available, then information banner

will be displayed with blanks.

If the selected channel is locked, you must enter the

correct four-digit numeric code to view the channel

(default code is 0000). “Enter PIN” will be displayed

on the screen in such a case:

Media Playback Using Media

Browser

If the USB stick is not recognized after power off/on

or First Time Installation, ﬁ rst, plug the USB device

out and power off/on the TV set. Plug the USB device

in again.

To display Media Browser window, press either “M”

button on the remote control and then select Media

Browser by pressing “

” or “ ” button. Press OK

button to continue. Media Browser menu options will

be displayed.

Also, when you plug USB devices, media browser

screen will be displayed automatically:

You can play music, picture and video ﬁ les from the

connected USB memory stick. Use “ ” or “ ” button

to select Videos, Photos, Music or Settings.

Viewing Videos via USB

When you select Videos from the main options,

available video ﬁ les will be ﬁ ltered and listed on this

screen. You can use “ ” or “ ” button to select a video

ﬁ le and press OK button to play a video. If you select

a subtitle ﬁ le and press OK button, you can select or

deselect that subtitle ﬁ le. The following menu will be

displayed while playing a video ﬁ le:

Jump (Numeric buttons): The TV will jump to the

ﬁ le starting with the letter you input via the numeric

buttons on your remote control.

Play This (OK button): Plays the selected ﬁ le.

Play (GREEN button): Plays all media ﬁ les starting

with the selected one.

Lang (Play Preview): Displays selected ﬁ le in a small

preview screen.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1601_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 16 13.05.2011 13:04:2613.05.2011 13:04:26

English - 17 -

INFO: Changes ﬁ lter options.

FAV: Sorts ﬁ les by name.

Play (RED button): Starts the video playback.

Stop (BLUE button): Stops the video playback.

Pause (OK button): Pause the video playback.

Rewind (

button): Goes backward.

Forward (

button): Goes forward.

Subtitle/Audio (LANG. button): Sets subtitle/Audio.

Yellow: Opens subtitle time correction menu

Press RETURN button to switch back to previous

menu.

Viewing Photos via USB

When you select Photos from the main options,

available image ﬁ les will be ﬁ ltered and listed on this

screen.

Jump (Numeric buttons): Jump to selected ﬁ le using

the numeric buttons.

OK: Views the selected picture in full screen.

Slideshow (GREEN button): Starts the slideshow

using all images.

Loop/Shufﬂ e (BLUE button): Press once to enable

Loop. Press again to enable both Loop and Shufﬂ e.

Press once more to enable only Shufﬂ e. Press again

to disable all. You can follow the disabled functions

with the change of the icons.

FAV: Sorts ﬁ les by date.

TEXT: Views images in thumbnails.

INFO: Changes ﬁ lter options.

Slideshow Options

Pause (YELLOW button): Pauses the slideshow.

Continue (GREEN button): Continues the slideshow.

Zoom (RED button) : Zooms picture.

Note: If a picture is zoomed out/displayed in full

screen, you cannot navigate the picture by using Up/

Down/Left/Right buttons.

Previous/Next (Left/Right buttons): Jumps to

previous or next ﬁ le on slideshow.

Rotate (Up/Down buttons): Rotates the image using

up/down buttons.

Loop/Shufﬂ e (BLUE button): Press once to disable

Loop. Press again to disable both Loop and Shufﬂ e.

Press once more to enable only Shufﬂ e. Press again

to enable all. You can follow the disabled functions

with the change of the icons.

RETURN: Back to ﬁ le list.

INFO: Displays help screen.

Viewing Music via USB

When you select Music from the main options,

available audio ﬁ les will be ﬁ ltered and listed on this

screen.

0..9 (Numeric buttons): The TV will jump to the

ﬁ le starting with the letter you input via the numeric

buttons on your remote control.

Play This (OK button): Plays the selected ﬁ le.

Play (GREEN button): Plays all media ﬁ les starting

with the selected one.

Stop (RED button): Stops playback.

Pause (YELLOW button): Pauses the selected

playback.

Previous/Next (Left/Right buttons): Jumps to

previous or next ﬁ le to play.

FAV: Sorts ﬁ les by Title,Artist or Album.

Note: If the Viewing Style is set to Folder in Media

Browser Settings, Music folder will be displayed as

sorted and there is no need to sort ﬁ les again by

pressing FAV button.

INFO: Changes ﬁ lter options.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1701_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 17 13.05.2011 13:04:2613.05.2011 13:04:26

English - 18 -

Loop/Shufﬂ e (Blue button): Press once to disable

Loop. Press again to disable both Loop and Shufﬂ e.

Press once more to enable only Shufﬂ e. Press again

to enable all. You can follow the disabled functions

with the change of the icons.

Media Browser Settings

You can set your Media Browser preferences by

using the Settings dialog. Press “

” or “ ” button to

highlight an item and use “

” or “ ” button to set.

View Style: Sets default browsing mode.

Slide Show Interval: Sets slide show interval time.

Show Subtitle: Sets subtitle enabling preference.

Subtitle Language: Sets supported subtitle

language.

Subtitle Position: Sets subtitle position as up or

down.

Subtitle Font Size: Sets subtitle font size (max.

54pt).

Changing Image Size: Picture

Formats

You can change the aspect ratio (image size) of •

the TV for viewing the picture in different zoom

modes.

Press • “SCREEN” button repeatedly to change

the image size. Available zoom modes are listed

below.

Auto

When AUTO is selected, the aspect ratio of the screen

is adjusted by the information provided by the selected

source(if available).

The format being displayed in AUTO mode is

completely independent of WSS information which

could be included in the broadcast signal or the signal

from an external device.

Note: Auto mode only will be available in HDMI, YPbPr

and DTV sources.

16:9

This uniformly stretches the left and right sides of a

normal picture (4:3 aspect ratio) to ﬁ ll the wide TV

screen.

For 16:9 aspect ratio pictures that have been •

squeezed into a normal picture (4:3 aspect ratio),

use the 16:9 mode to restore the picture to its

original shape.

Subtitle

This zooms up the wide picture (16:9 aspect ratio)

with subtitles to the full screen.

Note: You can shift to screen up or down by pressing

“ ” / “ ” buttons while picture zoom is selected as

panaromic, 14:9 Zoom, Cinema or Subtitle.

14:9

This zooms up the wide picture (14:9 aspect ratio) to

the upper and lower limits of the screen.

14:9 Zoom

This option zooms to the 14:9 picture.

4:3

Use to view a normal picture (4:3 aspect ratio) as this

is its original size.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1801_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 18 13.05.2011 13:04:2613.05.2011 13:04:26

English - 19 -

Panoramic

This stretches the left and right sides of a normal

picture (4:3 aspect ratio) to ﬁ ll the screen, without

making the picture appear unnatural.

The top and bottom of the picture are slightly cut off.

Cinema

This zooms up the wide picture (16:9 aspect ratio) to

the full screen.

Conﬁ guring Picture Settings

You can use different picture settings in detail.

Press “M” button and select the Picture icon by using

“

” or “ ” button. Press OK button to view Picture

Settings menu.

Operating Picture Settings Menu Items

Press “• ” or “ ” button to highlight a menu item.

Use “•

” or “ ” button to set an item.

Press • “M” button to exit.

Picture Settings Menu Items

Mode: For your viewing requirements, you can set

the related mode option. Picture mode can be set

to one of these options: Cinema,Game,Dynamic

and Natural.

Contrast: Sets the lightness and darkness values

of the screen.

Brightness: Sets the brightness value for the

screen.

Sharpness: Sets the sharpness value for the objects

displayed on the screen.

Colour: Sets the colour value, adjusting the colors.

Colour Shift: Adjust the desired colour tone.

Colour Temp: Sets the desired colour tone.

Setting Cool option gives white colours a slight blue

stress.

For normal colours, select Normal option.

Setting Warm option gives white colours a slight red

stress.

Noise Reduction: If the broadcast signal is weak and

the picture is noisy, use Noise Reduction setting to

reduce the noise amount. Noise Reduction can be set

to one of these options: Low, Medium, High or Off.

01_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 1901_woypbpr_MB60_[GB]_1825UK_IDTV_BRONZE17_19916WLED_10073683_50191891.indd 19 13.05.2011 13:04:2713.05.2011 13:04:27

Sayfa yükleniyor ...