Yamaha YHTS401 El kitabı

Printed in Indonesia

WY86610

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Bruksanvisning

Manuale di istruzioni

Manual de Instrucciones

Gebruiksaanwijzing

Инструкция по эксплуатации

Home Theater Package

(Subwoofer Integrated Receiver + Speaker)

Pack Numérique Home Cinéma

(Récepteur à caisson d’extrêmes graves intégré + Enceinte)

YHT-S401

(SR-301 + NS-BR301)

GF

i En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place –

away from direct sunlight, heat sources, vibration, dust,

moisture, and/or cold. For proper ventilation, allow the

following minimum clearances.

Top: 5 cm

Rear: 5 cm

Sides: 5 cm

3 Locate this unit away from other electrical appliances, motors,

or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from

cold to hot, and do not locate this unit in an environment with

high humidity (i.e. a room with a humidifier) to prevent

condensation inside this unit, which may cause an electrical

shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto

this unit and/or this unit may be exposed to liquid dripping or

splashing. On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to

this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain,

etc. in order not to obstruct heat radiation. If the temperature

inside this unit rises, it may cause fire, damage to this unit,

and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections

are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may

cause fire, damage to this unit, and/or personal injury.

Yamaha will not be held responsible for any damage resulting

from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and

outdoor antennas disconnected from a wall outlet or the unit

during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified

Yamaha service personnel when any service is needed. The

cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time

(i.e. vacation), disconnect the AC power plug from the wall

outlet.

16 Be sure to read the “Troubleshooting” section in the owner’s

manual on common operating errors before concluding that

this unit is faulty.

17 Before moving this unit, press to set this unit in standby mode,

and disconnect the power supply cable from the wall outlet.

18 Condensation will form when the surrounding temperature

changes suddenly. Disconnect the power supply cable from

the outlet, then leave the unit alone.

19 Install this unit near the wall outlet and where the AC power

plug can be reached easily.

20 The batteries shall not be exposed to excessive heat such as

sunshine, fire or like.

21 Secure placement or installation is the owner’s responsibility.

Yamaha shall not be liable for any accident caused by

improper placement or installation of speakers.

22 Never put a hand or a foreign object into the port located on

the front side of this unit. When moving this unit, do not hold

the port as it might cause personal injury and/or damage to

this unit.

23 Never place a fragile object near the port of this unit. If the

object falls or drops by the air pressure, it may cause damage

to the unit and/or personal injury.

■ Special Instructions for U.K. Model

■ For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

Caution: Read this before operating your unit.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN

OR MOISTURE.

As long as this unit is connected to the AC wall outlet,

it is not disconnected from the AC power source even

if you turn off this unit by . In this state, this unit is

designed to consume a very small quantity of power.

IMPORTANT

THE WIRES IN THE MAINS LEAD ARE

COLOURED IN ACCORDANCE WITH THE

FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows:

The wire which is coloured BLUE must be connected

to the terminal which is marked with the letter N or

coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

Note

1 En

INTRODUCTION PREPARATION

BASIC

OPERATION

USEFUL

OPERATION

ADDITIONAL

INFORMATION

English

■ About this manual

• In this manual, operations that can be performed using either the front panel buttons or the remote control are

explained using the remote control.

• y indicates a tip for your operation. Notes contain important information about safety and operating instructions.

• This manual is produced prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

What you can do with the unit

• Enjoy high quality surround sound (AIR SURROUND XTREME)..........................................................11

• Enjoy clear dialogue and narration (Clear voice).......................................................................................11

• Operate the unit by TV’s remote control (HDMI control function)...........................................................23

• Play back iPod/iPhone in high quality sound (Digital Connection for iPod/iPhone).................................16

• Expand the unit to 5.1 channel using speakers of your choice...................................................................20

INTRODUCTION

Getting started.........................................................2

Supplied parts ............................................................. 2

Remote control preparation ........................................ 2

Controls and functions ................................................ 3

PREPARATION

Placing......................................................................6

Operation by the TV remote control is difficult (with

the speaker beneath/under TV)............................... 6

Attaching the speaker to a wall................................... 7

Connection ...............................................................8

Connecting speakers ................................................... 8

Connecting a TV and BD player................................. 9

BASIC OPERATION

Basic playback operation......................................10

Listening with headphones ....................................... 10

Enjoying sound modes ..........................................11

Playback in surround sound...................................... 11

Playback in stereo sound........................................... 11

Clear voice ................................................................ 11

Compressed Music Enhancer.................................... 12

UniVolume................................................................ 12

Volume balance adjustment...................................... 12

Listening to FM broadcasts..................................13

Basic tuning operation .............................................. 13

Editing the preset FM station.................................... 13

Playing back iPod/iPhone and USB device.........16

Playing back.............................................................. 16

Repeat/shuffle playback............................................ 17

Displaying music information .................................. 17

Firmware update ....................................................... 17

USEFUL OPERATION

Setup menu.............................................................18

Setup menu list.......................................................... 18

Basic procedure......................................................... 18

Adjusting the volume balance of each channel ........ 19

Adjusting high/low frequency sound (tone control)

.............................................................................. 19

Configuring the HDMI settings................................ 19

Changing the brightness of the front panel display

.............................................................................. 19

Using other speakers................................................. 20

Dynamic range control.............................................. 21

Setting the matrix decode ......................................... 21

Settings for each input source (Option menu) ....22

Adjusting input level of each jack

(VOLUME TRIM) ............................................... 22

Adjusting the audio delay (AUDIO DELAY) .......... 22

Assigning the audio input to optical/coaxial digital

input (AUDIO ASSIGN)...................................... 22

Operating the unit by TV’s remote control ........23

What is the HDMI control function? ........................ 23

Setting the HDMI control function........................... 23

Registering HDMI components to TV ..................... 24

Changing the connection method and connected

components........................................................... 24

ADDITIONAL INFORMATION

Troubleshooting.....................................................25

Glossary..................................................................29

Specifications..........................................................31

Available signal information .................................... 32

Notes on remote controls and batteries..................... 33

Contents

2 En

INTRODUCTION

This product consists of the following items. Before making connections, make sure you have received all of the following

items.

■ Units

■ Accessories

Before installing batteries or using the remote control, make sure that you read precautions on the remote control and

batteries in “Caution: Read this before operating your unit.”, and “Notes on remote controls and batteries” on the page 33.

■ Installing the batteries ■ Operation range

Getting started

Supplied parts

Remote control preparation

Subwoofer Integrated Receiver (SR-301) Speaker (NS-BR301)

Speaker cable × 1 (3 m) Remote control × 1 Indoor FM antenna × 1

(U.S.A., Canada, Taiwan,

China and Asia models)

(U.K., Europe, Russia,

Australia and Korea

models)

TV remote

signal receptor × 1

Battery × 2 (AAA, R03, UM4) Mounting template × 1 Owner’s Manual

× 1

Within 6 m (20 ft)

3 En

Getting started

INTRODUCTION

English

■ Front panel of the subwoofer integrated receiver

1 STATUS indicator

Lights up to show the system condition. (☞ P. 10)

2 (Power)

Turns on the unit, or sets it to standby mode.

(☞ P. 10)

A small amount of electricity is consumed to receive the

infrared signal from the remote control even when the unit is

in standby mode.

3 INPUT

Selects an input source you want to listen to.

(☞ P. 10)

4 USB port

For connecting a USB device. (☞ P. 16)

5 VOLUME –/+

Controls the volume of the unit. (☞ P. 10)

6 PHONES jack

For connecting headphones. (☞ P. 10)

7 Remote control sensor

Receives infrared signals from the remote control.

(☞ P. 2, 5)

8 Front panel display

Shows information about the operational status of the

unit. (☞ P. 4)

■ Rear panel of the subwoofer integrated receiver

1 Power Cable

For connecting an AC wall outlet. (☞ P. 8)

2 HDMI IN 1 - 3/HDMI OUT (ARC) jack

• HDMI IN 1 - 3 for connecting HDMI

compatible external components. (☞ P. 9)

• HDMI OUT for connecting an HDMI compatible

TV. (☞ P. 9)

3 DIGITAL IN (TV) jack

For connecting optical digital cable to the TV.

(☞ P. 9)

4 DIGITAL IN (STB) jack

For connecting digital audio pin cable to the STB.

(☞ P. 9)

5 ANALOG INPUT jack

For connecting analog audio cable to external

components. (☞ P. 9)

6 ANTENNA terminal

For connecting supplied FM antenna. (☞ P. 9)

7 SPEAKERS terminal

For connecting speakers. (☞ P. 8)

Controls and functions

3

4

5

67

8

2

1

Note

1 2

57 6 43

4 En

Getting started

■ Front panel display of the subwoofer integrated receiver

1 HDMI indicator

Lights up during normal communication when HDMI

is selected as an input source.

2 Tuner indicators

TUNED indicator

Lights up when the unit is receiving a station.

(☞ P. 13)

STEREO indicator

Lights up when the unit is receiving a strong signal

from an FM stereo broadcast station in automatic

tuning mode. (☞ P. 13)

AUTO indicator

Flashes when the unit is tuning or presetting station

automatically. (☞ P. 13)

MEMORY indicator

Flashes when the unit is storing a station.

(☞ P. 13, 14)

EMPTY indicator

Lights up when the storing preset number is empty.

(☞ P. 14)

PS/PTY/RT/CT indicator (Europe and Russia

models only)

Lights up according to the available Radio Data

System information. (☞ P. 15)

3 Decoder indicators

The respective indicator lights up when any of the

decoders of the unit is activated.

4 Clear voice indicator

Lights up when Clear voice mode is selected.

(☞ P. 11)

5 VOLUME indicator

• Indicates the current volume level.

• Flashes while the mute function is activated.

(☞ P. 10)

6 Multi information display

Shows the selected input source, current sound mode

and other information.

7 ENHANCER indicator

Lights up when compressed music enhancer function

is activated. (☞ P. 12)

8 UNIVOLUME indicator

Lights up when UniVolume mode is selected.

(☞ P. 12)

1 2 3 4 5

8

7

6

5 En

Getting started

INTRODUCTION

English

■ Remote control

1 SURROUND

Selects the surround mode. (☞ P. 11)

2 STEREO

Turns extended stereo mode on and off alternately.

(☞ P. 11)

3 Input buttons

Select the input source you want to listen to.

(☞ P. 10)

Press the respective input button repeatedly to select

the input source.

TV/STB: TV, STB

HDMI1-3: HDMI1, HDMI2, HDMI3

ANALOG/FM: ANALOG, FM

USB: USB

4 MEMORY, TUNING / , PRESET / ,

INFO

Control an FM tuner. (☞ P. 13)

5 OPTION

Enters option menu for each input. (☞ P. 13, 16, 22)

6 (MENU), ( ), ( ), ( ),

ENTER

• Change setting.

• Control iPod/iPhone and USB device such as USB

flash memory, portable music player. (☞ P. 16)

S / T: Scroll screen of iPod/iPhone, or skip folder of

USB device. (☞ P. 16)

7 RETURN

• Cancels preset registration. (☞ P. 13)

• Returns to previous menu in option menu.

(☞ P. 22)

• Stops playback of USB device such as USB flash

memory or portable music player. (☞ P. 16)

8 SUBWOOFER +/–

Adjust volume balance of subwoofer. (☞ P. 10, 19)

9 ENHANCER

Turns Compressed Music Enhancer mode on and off.

(☞ P. 12)

0 LEVEL

Adjusts output level of speakers. (☞ P. 12)

A UNIVOLUME

Turns UniVolume mode on and off. (☞ P. 11)

B VOLUME +/–, MUTE

Control volume of the unit. (☞ P. 10)

C SETUP

Enters the setup menu. (☞ P. 18)

D CLEAR VOICE

Turns Clear voice mode on and off. (☞ P. 11)

E (Power)

Turns on the unit, or sets it to standby mode.

(☞ P. 10)

1

E

D

C

B

A

0

2

3

4

5

7

6

8

9

Infrared signal

transmitter

6 En

PREPARATION

To enjoy quality sound thoroughly, place this unit in the

appropriate positions, and install the components

properly. The following illustrations are the setting images

of this unit.

• Do not place this unit on/under any other components such as

BD player in a pile. The vibration of this unit may cause system

failure, etc. in other components.

• Keep enough ventilation space on the side, rear, and bottom

side (that attached legs) of this unit. Do not place this unit on a

thick carpet etc.

• Low frequency sound produced by the subwoofer integrated

receiver may be heard differently depending on the listening

position and subwoofer location. To enjoy desired sounds, try

changing the location of the subwoofer integrated receiver.

• Depending on your installation environment, connections to

external components can be done before installing this unit. We

recommend that you temporarily place and arrange all

components in order to decide which procedure is best done

first.

• When you clean this unit, use a clean, dry and soft cloth (such

as a cloth for glasses).

• Do not press the speaker grille when moving it.

When placing the subwoofer integrated

receiver in an upright position

Remove the stands and spacers on the bottom of the

subwoofer integrated receiver and attach them to the side,

as illustrated below.

TV remote control operation may be difficult if the

speaker hides the sensor of your TV when beneath or

under the TV. Try the solutions below and see whether

this solves the problem.

See the manual of your TV about where the sensor of your

TV remote control is.

1 Adjust the height of the speaker by using the

stands.

Remove the screws that secure the stands of the speaker,

and move the stands to adjust the height. Secure the stands

by the same screws, as illustrated below.

2 Use the TV remote signal receptor

The TV remote signal receptor (supplied) receives the

signal of the TV remote control, and transmits to the TV

remote control sensor. Place the TV remote signal

receptor as shown below.

Placing

Notes

Operation by the TV remote control

is difficult (with the speaker

beneath/under TV)

2

1

3

Signal receiver

Remove

the two

transparent

seals

Signal

emitter

TV remote

control

sensor

Position the signal

emitter to face the

center of TV remote

control sensor.

Attach the signal receptor

to the top of speaker

Approx. 10 mm (3/8 in)

7 En

Placing

PREPARATION

English

y

• Aim the TV remote control toward the top of TV remote signal

receptor.

• You can operate the TV remote control by using the TV remote

signal receptor even if the unit is in standby mode.

• Some TV remote controls may not work.

• You can attach the TV remote signal receptor in an area where

there are projections, such as the rear of speaker stand, etc.

• Clean the attachment area on the speaker, using a soft, dry

cloth, such as one for cleaning glasses.

• Clean the signal receiver and signal emitter of the TV remote

signal receptor, using a soft, dry cloth, such as one for cleaning

glasses.

Installing the speaker using the keyholes

You can attach the speaker to a wall using commercially

available screws (#8, Diameter: 4 mm (3/16”)).

1 Attach the supplied mounting template on a

wall and mark the holes of the mounting

template.

2 Remove the mounting template and then

install screws (not supplied) at the marks.

3 Hang the speaker on the screws using the

keyholes on the back of the speaker.

Installing the speaker using the screw holes

You can also use the screw holes on the rear of the speaker

for installing the speaker using a commercially available

rack etc.

• Attach the speaker to a rack or wall. Do not attach the speaker

to a wall that is made of weak materials such as plaster or

veneered woods. Doing so may cause the speaker to fall.

• Use commercially available screws that can support the weight

of the installation.

• Make sure you use specified screws to attach the speaker. Using

clamps other than specified screws, such as short screws, nails,

or two-sided tape, may cause the speaker to fall.

• When connecting the speaker, fix the speaker cables in place

where they will not become loose. If your foot or hand

accidentally gets caught on a loose speaker cable, the speaker

may fall.

• After attaching the speaker, check that the speaker is fixed

securely. Yamaha will bear no responsibility for any accidents

caused by improper installations.

Attaching the speaker to a wall

When installing the speaker on a wall, all

installation work must be performed by a

qualified contractor or dealer. The customer

must never attempt to perform this installation

work. Improper or inadequate installation could

cause the speaker to fall, resulting in personal

injury.

Tapes or thumbtacks

Mark

2 to 4 mm (1/16” to 3/16”)

7 to 9 mm

(1/4” to 3/8”)

Minimum

20 mm (3/4”)

4 mm (#8)

Notes

Screw holes

Hole depth: 14 mm (9/16”)

Diameter: 6 mm (1/4”)

256 mm

(10-1/16”)

38.5 mm (1-9/16”)

Rack etc.

14 mm (9/16”)

Screw

(M6)

Screw

hole

Min 7 mm (1/4”)

NS-BR301

8 En

Follow the procedure below to connect the subwoofer integrated receiver and speakers.

y

• Additional surround speakers (commercially available) are required for 5.1ch playback.

• Refer to “Using other speakers” (☞ P. 20) when using additional speakers.

Connection

• Do not connect the power cable until all connections are completed.

• Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or

terminal.

Connecting speakers

Surround speakers

(sold separately)

y

Twist and pull off the

insulation tube on the lead

wire.

Twist and pull off the

insulation tube on the

lead wire.

Insert into the terminal by matching the wire color

with the color-coded terminal on the rear panel.

5.1ch playback

RL

To AC outlet

Speaker (NS-BR301)

Insert into the terminal by matching

the wire color with the color-coded

terminal on the rear panel.

Brown Black Gray

Red Green White

9 En

Connection

PREPARATION

English

Follow the steps below for cable connection according to the components you use.

*1 y

For HDMI control function, an optical cable is not required if the TV’s “ARC” terminal is used “2”. Audio return channel (ARC) carries

digital audio signal (from the TV) to this unit via an HDMI cable. Activate the HDMI control function of this unit to enable ARC

function. (☞ P. 19)

*2

y

Connect analog pin cables (sold separately) to the analog audio output jacks of an external device, such as a VTR, to play back analog

audio sound.

*3

y

Connect a digital audio pin cable (sold separately) to the coaxial digital output jack of a satellite/cable TV tuner to play back digital

sound.

Connecting a TV and BD player

1 HDMI cable (sold separately) 2 HDMI cable (sold separately)

3 Optical cable (sold separately)*

1

4 Indoor FM antenna (supplied)

y

If the radio wave reception is weak in your area or you want to

improve the radio wave reception, we recommend that you use an

outdoor antenna. For details, consult your nearest authorized

Yamaha dealer or Service Center.

HDMI INPUT

(Example)

1 Remove the cap 2 Check the

direction of the

plug

TV

BD player

Game console

1

Video signals

Audio signals

1

2

3*

1

*

3

*

2

4

10 En

BASIC OPERATION

Once you have finished all cable connections and remote control operation, follow the procedure below to start basic

playback operation.

1 Press (Power).

This unit is turned on and the STATUS indicator

lights green.

The input source and surround mode appear in the

front panel display.

y

This unit has the auto-sleep function, which will

automatically switch the unit to turn off if the unit is left

turned on for 12 hours without any operation being

performed.

2 Press one of the input buttons to select an

input source.

After the input source name has been displayed in the

front panel display for three seconds, the front panel

display returns to its normal display. (Input source

name: surround/stereo mode).

3 Start playback on the selected external

component.

For information on the external component, refer to

the instruction manual for the product.

4 Press VOLUME +/– to adjust the volume

level.

Press SUBWOOFER +/– to adjust the

subwoofer level.

y

• To turn off the volume temporarily, press MUTE. While

the mute function is activated, the VOLUME indicator

flashes. To resume the volume, press MUTE again or

press VOLUME +/–.

• When audio is output from both TV speaker and this unit,

mute the TV sound.

• The subwoofer volume can be adjusted separately from

the volume.

• You can also adjust the subwoofer volume listening to test

tone. (☞ P. 19)

• Lowering the subwoofer volume is recommended at night.

When sound of HDMI is output from the TV, the volume

level does not change if you press VOLUME +/– or MUTE

of the remote control.

5 Select surround mode or stereo mode and

set your sound preferences. (☞ P. 11)

Insert a headphone plug to the PHONES jack (☞ P. 3) of

this unit.

• The headphone volume, tone control can be set

separately with speaker setting.

• You can enjoy surround and stereo sound using a

headphone same as the speaker. (☞ P. 11)

Basic playback operation

You can operate the unit by the TV’s remote control

when the HDMI control function is available. See the

page 23 for details.

1

2

4

Note

Press (Power) again to set the unit to

standby mode.

When the HDMI control function is set to on or the battery of

iPod/iPhone is charged, the STATUS indicator lights red. When

the HDMI control function is set to off, the STATUS indicator

turns off. (☞ P. 3)

Listening with headphones

11 En

BASIC

OPERATION

English

You can enjoy a realistic sound effect.

Press SURROUND to set surround mode.

Press SURROUND repeatedly until desired mode appears

in the front panel display.

Surround mode descriptions in following order

*1

This mode is available only during playback with surround

speakers connected. (☞ P. 20)

y

• The unit automatically memorizes the settings assigned to each

input source.

• The unit creates high quality 7.1 channel surround playback by

employing AIR SURROUND XTREME technology in the

absence of surround speakers.

• Depending on settings you choose, the unit may not decode

DTS-HD Master Audio sound or DTS-HD High Resolution

Audio sound. In such cases, only the DTS is decoded.

An extended sound is achieved for a 2 channel source

such as a CD player.

Press STEREO to enter extended stereo mode.

Each time you press STEREO, the function is turned on

(EXTENDED STEREO) and off (STEREO) alternately.

“STEREO”: Reproduces the sound without any effect.

“EXTENDED STEREO”: Reproduces a wider stereo

image.

y

• The default setting is “EXTENDED STEREO”.

• The unit memorizes the settings assigned to each input source.

This function makes dialogue in movies, TV dramas or

play-by-play broadcasting clear to listen to.

Press CLEAR VOICE to turn the function on/off.

When Clear voice is activated, “●” (Clear voice) indicator

is displayed.

y

The unit memorizes the setting assigned to each input source.

Enjoying sound modes

SURROUND

CLEAR VOICE

STEREO

Playback in surround sound

Display Effect

MOVIE This mode is useful when you enjoy movie

contents on media.

MUSIC This mode is useful when you listen to music

contents on media.

SPORTS This mode is useful when you enjoy sports

programs.

GAME This mode is useful when you enjoy video

games.

TV PROGRAM

(TV PROG)

This mode is useful when you enjoy a general

TV program.

STANDARD

*1

Play back without sound effect.

Playback in stereo sound

Clear voice

Enjoying sound modes

12 En

Play back digitally compressed format such as MP3 and

WMA emphasizing bass and treble extended dynamically.

Press ENHANCER to turn the function on/off.

When Compressed Music Enhancer is activated,

ENHANCER indicator is displayed.

y

The unit memorizes the settings assigned to each input source.

While watching the TV, compensate the excessive volume

differences to make it easier to hear during the following

cases.

• When switching the channel

• When a TV program changed to commercial

• When one program is finished and another program

started

Press UNIVOLUME to turn the function on/off.

When UniVolume is activated, UNIVOLUME indicator is

displayed.

y

The unit memorizes the settings assigned to each input source.

You can adjust the volume balance of the virtual speakers

and subwoofer during playback.

1 Press LEVEL repeatedly to select adjustable

channels from the followings.

Available options

2 Press / to adjust the volume level

while the channel you selected is displayed.

Adjustable range: –6 to +6 (Default setting: 0)

y

The subwoofer volume is adjustable by pressing

SUBWOOFER +/-.

• You cannot adjust the volume balance when using the

headphone.

• This setting of each channel is available for all input

source.

SUBWOOFER +/–

ENHANCER

UNIVOLUME

LEVEL

/

Compressed Music Enhancer

UniVolume

Volume balance adjustment

FRONT L,

FRONT R

Front speaker (left/right)

CENTER Center speaker

SURROUND L,

SURROUND R

Virtual surround speaker, and surround

speakers (left/right)

SUBWOOFER Subwoofer

Notes

13 En

BASIC

OPERATION

English

■ Automatic preset

You can store up to 40 FM stations (01 to 40).

1 Press ANALOG/FM repeatedly to select FM

input.

2 Press OPTION to enter the option menu.

“1.VOLUME TRIM” appears firstly in the front

panel display.

3 Press / to select “2.AUTO PRESET”

and press ENTER.

y

Press PRESET / repeatedly to select a preset number

to which the first station will be stored.

After approximately 5 seconds, automatic presetting

starts from the lowest frequency and proceeds

through higher frequencies. When the frequency is

stored, the TUNED indicator lights up.

When automatic preset tuning is completed, the front

panel display shows message “Preset Complete” for

three seconds firstly and returns to the option menu

secondly.

y

Press RETURN while searching automatically, automatic preset

is stopped.

• Any stored station data existing under a preset number is

cleared when you store a new station under the same preset

number.

• If the number of received stations does not reach 40, automatic

preset tuning automatically stops after searching for all the

available stations.

• Only the station with strong signals can be stored. If the desired

station is not stored, or a station is not stored to the desired

preset number, preset the station manually. (☞ P. 14)

Listening to FM broadcasts

Basic tuning operation

Editing the preset FM station

ANALOG/FM

Press repeatedly to set the input

to FM.

TUNING /

Press to change the frequency by 1

step, or press and hold to search

stations automatically.

PRESET /

Select the preset FM stations.

INFO

Selects the information

displayed in the front panel

display.

OPTION

Enters the option menu when the

input is set to FM.

Cursor in the option menu

MEMORY

Stores preset stations manually.

RETURN

Returns to the previous menu or

cancels the operation.

Notes

Listening to FM broadcasts

14 En

■ Manual station preset

Use this feature to preset your desired station manually.

1 Tune into a radio station you want to preset.

2 Press MEMORY.

“MANUAL PRESET” appears in the front panel

display, followed soon by the preset number to which

the station will be registered.

y

By pressing down MEMORY for more than 2 seconds, the

station is registered to the lowest empty preset number or a

preset number one higher than the last preset number.

3 Press PRESET / to select the preset

number (01 to 40) to which the station will be

registered.

When you select a preset number to which no station

is registered, EMPTY indicator appears on the

display. When you select a registered preset number,

a registered frequency is displayed on the right of the

preset number.

y

To cancel registration, press RETURN on the remote

control or leave the tuner without any operations for about

30 seconds.

4 Press MEMORY again to register.

■ Clearing the preset station

1 Press OPTION to enter the option menu.

2 Display “3.CLEAR PRESET” using /

and press ENTER.

Preset number and the frequency appears in the front

panel display.

y

You can cancel the operation and return to the option menu

by pressing RETURN on the remote control.

3 Select the preset number of the registered

station you want to clear using / and

press ENTER.

The preset station registered to the selected preset

number is cleared. To clear the registration of

multiple preset numbers, repeat the above steps.

To end the operation, press OPTION.

■ Using the monaural reception

mode

When the signal of the desired FM station is too weak, set

the reception mode to “MONO” to increase signal quality.

1 Press OPTION to enter the option menu.

2 Display “4.STEREO/MONO” by using and

press ENTER.

3 Select “MONO” to set the reception mode to

monaural by using / .

Listening to FM broadcasts

15 En

BASIC

OPERATION

English

■ Switching the information display

Each time you press INFO, the information display

changes as follows:

Information type

• SURROUND MODE

Displays the surround mode or stereo mode.

• FREQUENCY

Displays the frequency and preset number.

• PROGRAM SERVICE (PS)

Displays the currently received Radio Data System

program.

• PROGRAM TYPE (PTY)

Displays the type of the currently received Radio Data

System program.

• RADIO TEXT (RT)

Displays the information of the currently received

Radio Data System program.

• CLOCK TIME (CT)

Displays the current time.

■ Using the TP (traffic program)

data service (Europe and Russia

models only)

Use this feature to receive the TP (traffic program) data

service of the Radio Data System station network.

1 Press OPTION to enter the option menu.

2 Press / to select “5.TRAFFIC PROG”

and press ENTER.

The search starts automatically. The AUTO indicator

and “TP” in the multi information display flash

during the search. When a traffic program is received,

“TP” and frequency remain displayed, and the search

finishes.

If the unit fails to receive a traffic program, “TP” and

the frequency turn off, and “TP Not Found” appears

in the front panel display.

y

• Press RETURN to cancel a search.

• If no operation is performed for 30 seconds during search,

the option menu closes and the search is cancelled.

Europe and Russia models only

16 En

Connect a USB device, such as iPod/iPhone, USB flash

memory or portable music player, to play back audio files.

Battery charge feature

The battery of a connected device can be charged when

the unit is on. An iPod/iPhone connected to the unit keeps

on being charged even if the unit is set to standby mode.

Supported iPod/iPhone

iPod classic

iPod nano (3rd Generation to 6th Generation)

iPod touch

iPhone

iPhone 3G

iPhone 3GS

iPhone 4

y

• Some features may not be available depending on the model or

the software version of your iPod/iPhone.

• For a complete list of status messages that appear in the front

panel display, see the “Messages for iPod/iPhone and USB

device” section in “Troubleshooting” (☞ P. 27).

• Be sure to set the volume to minimum before removing your

iPod/iPhone.

Supported USB devices

A USB flash memory and USB portable music player

formatted in FAT format and supporting for USB Mass

Storage Class

Some USB devices may not be supported, even in the above.

1 Press USB to select USB input.

2 Play back the iPod/iPhone or USB device.

*1

Resumes playing the music last played back (resume playback)

*2

The folder name appears in the front panel display for three

seconds when skipped.

y

The unit automatically plays back the iPod/iPhone or USB device

in the following cases.

• When setting the input to USB, while the unit is on and an iPod/

iPhone or USB device is connected.

• When the input setting is USB at the time the unit is turned on

with an iPod/iPhone or USB device.

• When a playing iPod/iPhone is connected to the unit that is

turned on. (The input setting is automatically set to USB.)

Playing back iPod/iPhone and USB device

Note

Playing back

iPod/iPhone USB device

: play/pause

: skip forward (press and

hold: fast-forward)

: skip backward (press and

hold: fast-rewind)

▲/▼: scroll the screen

: play/pause

*1

: skip forward (press and

hold: fast-forward)

: skip backward (press and

hold: fast-rewind)

RETURN: stop

FOLDER ▲/▼: skip the

folder

*2

OPTION

ENTER

INFO

SETUP

FOLDER

▲/▼

/

USB

RETURN

Playing back iPod/iPhone and USB device

17 En

BASIC

OPERATION

English

1 Press OPTION to enter the option menu.

2 Press / to select “2.REPEAT” and

press ENTER.

3 Press / to select the available option

and press ENTER.

Available options (Default setting: OFF)

■ Shuffle playback of iPod/iPhone

1 Press OPTION to enter the option menu.

2 Press / to select “3.SHUFFLE” and

press ENTER.

3 Press / to select the parameter and

press ENTER.

Available options (Default setting: OFF)

OFF: Cancels shuffle playback

SONGS: Plays back music in random order.

ALBUMS: Plays back albums in random order.

You can display information on the music currently

playing back.

Press INFO.

Press INFO repeatedly to switch the information

(displayed for three seconds) in the order below.

iPod/iPhone: SONG (music name) → PLAY TIME

(playback time) → ARTIST (artist name) → ALBUM

(album name) → SONG (music name)

USB device: FILE (file name) → PLAY TIME (playback

time) → SONG (music name) → ARTIST (artist name) →

ALBUM (album name) → FILE (file name)

• If the information cannot be displayed entirely in the front panel

display, it is scrolled once.

• There are some characters that cannot be displayed in the front

panel display of this unit.

You can update the firmware of this unit.

1 Copy the firmware data into USB flash

memory. Then connect the USB flash

memory to the USB port on the front panel of

this unit.

Make sure that you copy the firmware file into the

root directory of the USB flash memory. Refer to the

documentation associated with the firmware file.

2 Press SETUP.

3 Press / to select “6:FIRMWARE” and

press ENTER.

4 Press / to select “6-2:USB UPDATE”

and press ENTER.

The update starts.

y

• Press / to select “6-1:VERSION” and you can see the

version of this unit firmware displayed in the front panel

display.

• See the “Messages for firmware update” section in

“Troubleshooting” (☞ P. 28) about the messages for firmware

update that appear in the front panel display.

Repeat/shuffle playback

iPod/iPhone USB device

OFF

Cancels repeat

playback

Cancels repeat

playback

ONE

Repeats playing back a

music singly

Repeats playing back a

music singly

ALL

Plays back all the music

repeatedly in your iPod/

iPhone

Plays back all the music

repeatedly in your USB

device

FOLDER

Plays back all the music

repeatedly in the folder

saved in your USB

device

RANDOM

Plays back all the music

at random in the folder

saved in your USB

device

Displaying music information

Notes

Firmware update

18 En

USEFUL OPERATION

You can change various settings of this unit using the

setup menu.

1 Press SETUP to enter the setup menu.

“1:SP LEVEL” is displayed in the front panel

display.

2 Press / to select menu and press

ENTER.

Repeat this procedure until desired menu/sub menu is

displayed.

3 Press / to adjust the value of each

menu.

Press and hold / to change the setting value

faster.

4 Press SETUP again to exit the setup menu.

y

• Press RETURN or to return to the previous menu.

• Press to enter the next menu.

If you do not operate within 30 seconds after entering the setup

menu, the unit automatically exits the setup menu.

Setup menu

Setup menu list

Menu Sub menu Features Page

1:SP LEVEL 1-1:FRONT L

Adjusting the volume balance with test tone ☞ P. 19

1-2:FRONT R

1-3:CENTER

1-4:SURROUND L

1-5:SURROUND R

1-6:SUBWOOFER

2:TONE CONTROL 2-1:BASS

Adjusting high/low frequency sound (tone control) ☞ P. 19

2-2:TREBLE

3:HDMI SETUP 3-1:CONTROL

Configuring the HDMI settings ☞ P. 19

3-2:AUDIO

4:DISPLAY MODE Changing the brightness of the front panel display ☞ P. 19

5:SP SETUP 5-1:SP CHANNEL Selecting the number of channel

☞ P. 20

5-2:SP TYPE Changing the setting of the speaker type

5-3:SP DISTANCE Setting the distance between the speakers

5-4:CROSSOVER Cutting the crossover register

6:FIRMWARE 6-1:VERSION Displaying the firmware version of this unit

☞ P. 17

6-2:USB UPDATE Updating the firmware of this unit

7:D.RANGE Adjusting the dynamic range ☞ P. 21

8:MATRIX DECODE 8-1:DECODE MODE Selecting the decoder

☞ P. 21

8-2:C.IMAGE Adjusting the center image

Basic procedure

ENTER

SETUP

/

RETURN

Note

Sayfa yükleniyor...

Yamaha YHTS401 El kitabı

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Yamaha YHTS401 El kitabı

diğer dillerde

İlgili makaleler

Diğer belgeler