Yamaha MX-A5000 El kitabı

English

Français

Deutsch

Español

Русский

中文

한국어

Power Amplifier/Ampli de Puissance

Owner’s Manual

Mode d’emploi

Bedienungsanleitung

Manual de Instrucciones

Инструкция по эксплуатации

使用说明书

사용 설명서

MX-A5000_om_UCTKABGLVF.book Page 1 Thursday, April 4, 2013 5:28 PM

i En

Precaution for use

Read the supplied booklet “Safety Brochure” before using the unit.

Install the unit in a well ventilated, cool, dry, clean place – away from direct sunlight,

heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at

least 30 cm (11-3/4”) on the top, 20 cm (7-7/8”) on the left and right, and 20 cm

(7-7/8”) on the back of the unit.

30 cm (11-3/4”) or more

20 cm (7-7/8”) or more

Since the unit adopts bare metallic speaker terminals, make sure keeping enough

space on the back of the unit. If the speaker terminals come into contact with metal

parts of the AV rack, etc., the unit will be shortened and damaged.

Also, never touch the speaker terminals when the unit is powered on since it may

cause an electrical shock.

The unit does not have volume controls. Make sure you connect a device with

volume control (such as a pre-amplifier) to the unit. If you connect a device without

volume control (such as a CD player) directly to the unit, the volume may become

excessively loud and result in damage to the unit or speakers.

Be careful with short circuits.

DO NOT TOUCH!

(when the unit is powered on)

MX-A5000_om_UCTKABGLVF.book Page i Thursday, April 4, 2013 5:28 PM

En 1

CONTENTS

Precaution for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .i

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Part names and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Connecting speakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Connecting the power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turning on/off the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Other functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turning off the unit automatically (auto-standby function) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Dimming the power indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Turning on the unit in conjunction with operating other devices (trigger function) . . . . . . . . . . . . . . . . . . . 9

Advanced speaker configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using a speaker that supports bi-amp connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using two pairs of front speakers (SPEAKERS A/B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Using three speakers for one channel (multi-speaker) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Input-output signal path diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Accessories

Check that the following accessories are supplied with the product.

 Power cable

*The supplied power cable varies depending on the region of purchase.

 System control cable

 Owner’s Manual

• Due to product improvements, specifications and appearance are subject to change without notice.

• indicates precautions for use of the unit and its feature limitations.

• indicates supplementary explanations for better use.

MX-A5000_om_UCTKABGLVF.book Page 1 Thursday, April 4, 2013 5:28 PM

2 En Features

Features

High-quality power amplifier

■ High output/high audio-quality

amplifier (150 W x 11 channels)

The unit provides an 11-channel power amplifier

featuring a three-stage Darlington current feedback

circuit, with a power supply that uses the same type of

toroidal transformer used in top-level hi-fi audio devices.

The gold-plated speaker connectors are also of the

highest quality, delivering high-grade sound.

■ Balance and unbalanced

connections are supported

Balanced (XLR) and unbalanced (RCA) input jacks are

provided on all channels, and can be selected

independently for each channel.

Balanced connections minimize the extraneous noise

that can arise in the cable connection between the unit

and the pre-amplifier, ensuring high-fidelity transmission

of the audio signal.

Unbalanced connections utilize ground-sensing to

achieve fidelity that is close to balanced transmission.

■ Chassis structure that maximizes

the potential of the unit's

performance

The chassis features a special structure that allows the

full potential of the high-quality power amplifier’s

potential to be revealed.

• Symmetrical power amplifier design

• Aluminum front panel and side panels

• Extremely stable feet utilizing the A.R.T.

(Anti-Resonance Technology)

Expandable to meet diverse needs

■ Freedom for speaker placement

Since power amplifiers of the identical specification are

provided for all 11 channels, you use the unit not only

for constructing a home theater setup of up to

11 channels but also for multi-room systems or any

other speaker configuration to meet your needs.

■ Support for bi-amp connections

and multi-speaker playback

The unit provides a channel selector function that lets

you utilize bi-amp connections or multi-speaker

connections without having to connect additional

cables from your pre-amplifier. For example, the CH.2

audio input could be output from both the CH.2 and

CH.3 speaker outputs to drive a bi-amp configuration

for high-quality sound, or the CH.1 (monaural) input

could be output from three speakers connected to CH.1

and CH.4 (L/R).

■ Switch the unit's power from your

pre-amplifier (trigger function)

The unit can switch its own power status in

synchronization with power switching operations on

another device that supports the trigger function, such

as an AV pre-amplifier (TRIGGER IN). The input signal

from the TRIGGER IN jack can also be output without

change in a cascade connection to switch the power of

another device such as a Yamaha subwoofer

(THROUGH OUT). In addition, another device can be

switched in synchronization when the power of the unit

is switched (TRIGGER OUT), allowing you to set up a

variety of systems with synchronized power switching.

Pre-amplifier

MX-A5000_om_UCTKABGLVF.book Page 2 Thursday, April 4, 2013 5:28 PM

Part names and functions En 3

Front panel

1 z (power) key

Turns on/off (standby) the unit (p.8).

2 Power indicator

Lights up when the unit is turned on.

If the indicator blinks, the protection circuitry has been

activated. For details, see “Troubleshooting” (p.12).

• You can dim the power indicator (p.8).

3 SPEAKERS A/B keys

Turns on /off the speakers connected to the CH.2 A/B

terminals (p.10).

• Both the speakers (A and B) are turned off by default. Press the

key to turn on the speakers you want to use.

• When using two pairs of the speakers connected to the CH.2

A/B terminals at the same time, be sure to use 8-ohm speakers

and set IMPEDANCE SELECTOR to the upper position (p.7).

Part names and functions

SPEAKERS

ON OFF

AB

21

3

MX-A5000_om_UCTKABGLVF.book Page 3 Thursday, April 4, 2013 5:28 PM

4 En Part names and functions

Rear panel

1 SPEAKERS terminals

For connecting to speakers (p.7).

2 TRIGGER jacks

For connecting to devices that support the trigger function (p.9).

3 AUTO POWER STANDBY switch

Enables/disables the auto-standby function (p.8).

4 IMPEDANCE SELECTOR

Changes the unit’s speaker impedance setting depending

on the speakers connected (p.7).

5 AC IN jack

For connecting the supplied power cable (p.8).

6 CH. SELECTOR

(CH.3, CH.4 and CH.6 only)

Selects the audio source input to the CH.3, CH.4 or CH.6

amplifier when applying a bi-amp connection (p.10) or a

multi-speaker connection (p.10).

AC IN

R

SPEAKERS

TRIGGER

INPUT

+12V

IN

THROUGH

OUT

BAL. UNBAL.

AUTO POWER

STANDBY

IMPEDANCE

SELECTOR

SELECTEUR

D’IMPEDANCE

OUT

OFF

ON

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

CH.1

L

SPEAKERS

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

12V 0.1A

R

BAL. UNBAL.

CH.2

BAL. UNBAL.

CH.1

L

BAL. UNBAL.

CH.2

L

BAL. UNBAL.

CH.5

R

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

R

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

R

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

L

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

BAL. UNBAL.

CH. SELECTOR

3

4 5

6

7

8

9

11 2

Caution

• Remove the unit’s power cable from an AC wall outlet before

making any connections or operating the switches and/or

selectors.

MX-A5000_om_UCTKABGLVF.book Page 4 Thursday, April 4, 2013 5:28 PM

Part names and functions En 5

7 INPUT (XLR) jack

For connecting to a pre-amplifier with XLR output jacks (p.6).

To use the XLR jack, set the corresponding BAL/UNBAL

switch to “BAL”.

When connecting an XLR balanced cable, match the pins

and insert the “male” connector of the cable until you hear a

click.

• When disconnecting the cable from the unit, hold down the PUSH

button on the unit and then pull the connector out.

8 INPUT (RCA) jack

For connecting to a pre-amplifier with RCA output jacks

(p.6).

To use the RCA jack, set the corresponding BAL/UNBAL

switch to “UNBAL”.

• Remove the RCA short pins attached to the INPUT (RCA) jacks

before making connections. Be sure to keep them in a place

inaccessible to small children who may accidentally swallow

small parts.

• To protect against noise contamination, we recommend

attaching the RCA short pins when the INPUT (RCA) jacks are

not in use.

9 BAL/UNBAL switch

Switches between XLR input and RCA input for each channel

(p.6).

About the XLR jacks

• The pin assignments for the XLR jacks of the unit are shown

below. Before connecting an XLR balanced cable, refer to the

instruction manual of your pre-amplifier and verify that its XLR

output jacks are compatible with the pin assignments.

BAL. UNBAL.

XLR balanced cable (male)

3. COLD

2. HOT

1. GND

BAL. UNBAL.

RCA cable

RCA short pin

MX-A5000_om_UCTKABGLVF.book Page 5 Thursday, April 4, 2013 5:28 PM

6 En Connections

Connect a pre-amplifier and speakers to the unit.

To connect a pre-amplifier, use an XLR balanced cable (for balanced connection) or an RCA unbalanced cable (for unbalanced connection) for each channel depending on the

output jacks available on your pre-amplifier.

Connections

Caution

• Remove the unit’s power cable from an AC wall outlet before making any connections or operating the switches and/or selectors.

AC IN

R

SPEAKERS

TRIGGER

INPUT

+12V

IN

THROUGH

OUT

BAL. UNBAL.

AUTO POWER

STANDBY

IMPEDANCE

SELECTOR

SELECTEUR

D’IMPEDANCE

OUT

OFF

ON

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

CH.1

L

SPEAKERS

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

12V 0.1A

R

BAL. UNBAL.

CH.2

BAL. UNBAL.

CH.1

L

BAL. UNBAL.

CH.2

L

BAL. UNBAL.

CH.5

R

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

R

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

R

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

L

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

BAL. UNBAL.

XLR

The unit (rear)

SPEAKERS (R) terminals SPEAKERS (L) terminals

INPUT (XLR or RCA) jacks

* Set the BAL/UNBAL switch for each channel

to “BAL” (XLR) or “UNBAL” (RCA)

depending on the connection type.

Pre-amplifier

Preout (XLR or RCA)

jacks

Subwoofer connections

* For details, refer to the instruction manuals

for your pre-amplifier and subwoofers.

Speaker connections (p.7)

MX-A5000_om_UCTKABGLVF.book Page 6 Thursday, April 4, 2013 5:28 PM

Connections En 7

Connecting speakers

■ Note on the speaker impedance

The unit supports the following speaker impedance.

• CH.2 A/B: 4  or more (8  or more when using CH.2 A and CH.2 B at the same time)

• Other channels: 6  or more

Set the IMPEDANCE SELECTOR to the upper/lower position depending on the

speakers connected to the unit.

■ Connecting speaker cables

Speaker cables have two wires. One is for connecting the negative (-) terminal of the unit and

the speaker, and the other is for the positive (+) terminal. If the wires are colored to prevent

confusion, connect the black wire to the negative and the other wire to the positive terminal.

a Remove approximately 10 mm (0.40 in) of insulation from the ends of the speaker cable,

and twist the bare wires of the cable firmly together.

b Loosen the speaker terminal.

c Insert the bare wires of the cable into the gap on the side (upper left or bottom right) of the

terminal.

d Tighten the terminal.

Using a banana plug

(U.S.A., Canada, China, Taiwan and Australia models only)

a Tighten the speaker terminal.

b Insert a banana plug into the end of the terminal.

Using a Y-shaped lug connector

a Loosen the speaker terminal.

b Insert the Y-shaped lug connector into the groove between the knob and base part of the

terminal.

c Tighten the terminal.

Upper position

Select this option when your speaker system meets one of the followings.

• When connecting speakers with impedance of less than 8  (4  or more) to the

CH.2 A or CH.2 B terminal

• When using two pairs of speakers connected to the CH.2 A/B terminals at the

same time (be sure to use 8-ohm speakers for both CH.2 A and CH.2 B)

• When connecting speakers with impedance of less than 8  (6  or more) to

speaker terminals other than CH.2 A or CH.2 B

Lower position

(default)

Select this option when using speakers with impedance of 8

 or more only.

aa

b

d

c

aa

b

Banana plug

aa

b

c

Use a Y-shaped lug

with the following size.

6.5 mm

(0.26 in)

or more

MX-A5000_om_UCTKABGLVF.book Page 7 Thursday, April 4, 2013 5:28 PM

8 En Other functions

Connecting the power cable

After all the connections and switch operations are complete, connect the supplied

power cable to the unit and then to an AC wall outlet.

Turning on/off the unit

Press z (power) to turn on/off the unit.

When the unit is turned on, the power indicator lights up.

• When an external device is connected to the TRIGGER IN jack, the unit is set to standby mode after

z (power) is pressed. If you turn on the external device, the unit automatically turns on by the trigger

function (p.9).

Turning off the unit automatically

(auto-standby function)

The unit will automatically go into standby mode 8 hours after the unit is turned on.

To disable the auto-standby function, set the AUTO POWER STANDBY switch to “OFF”.

• The auto-standby function works even if playback is ongoing.

• When the system control cable is connected to the TRIGGER IN jack, the auto-standby function does not

work even if it is enabled.

Dimming the power indicator

You can dim the power indicator on the front panel of the unit.

• When an external device is connected to the TRIGGER IN jack, turn on it before performing the following

procedure.

a If the unit is turned on, press z (power) to turn off it.

b Press z (power) three times within 3 seconds.

The power indicator dims.

• To cancel the dimmer, perform the procedure again.

• If the power cable is unplugged, the dimmer will be canceled.

AC IN

CH.4

CH.3

CH.2

B

CH.2

A

L

BAL. UNBAL.

CTOR

H.4

L

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

L

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

To an AC wall outlet

The unit (rear)

z (power)

The unit (front)

Other functions

MX-A5000_om_UCTKABGLVF.book Page 8 Thursday, April 4, 2013 5:28 PM

Other functions En 9

Turning on the unit in conjunction with operating other devices (trigger function)

The trigger function can control power of the unit in conjunction with operating other

devices or control power of other devices in conjunction with turning on/off the unit. If

you have a power amplifier or a Yamaha subwoofer that supports the trigger function,

you can use the trigger function by connecting your devices to the TRIGGER jacks with

the supplied system control cable.

Depending on the intended use, connect your device to one of the following TRIGGER

jacks.

IN jack:

For connecting a device that supports the trigger output function (such as a

pre-amplifier).

If you turn on/off your device, the unit will automatically turns on/off (standby).

• This function is available only when z (power) of the unit is on (pressed down).

THROUGH OUT jack:

This jack outputs signals input from the IN jack.

If you connect a device that supports the trigger input function (such as another power

amplifier), your device will automatically turn on/off in conjunction with turning on/off the

device connected to the IN jack.

OUT jack:

For connecting a device that supports the trigger input function (such as a subwoofer).

If you turn on/off (standby) the unit, your device will automatically turns on/off.

• To connect multiple devices to the TRIGGER jacks, you need to prepare commercially-available monaural

mini-plug cables.

R

TRIGGER

+12V

IN

THROUGH

OUT

BAL. UNBAL.

AUTO POWER

STANDBY

IMPEDANCE

SELECTOR

SELECTEUR

D’IMPEDANCE

OUT

OFF

ON

CH.5

12V 0.1A

R

CH.2

R

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

R

CH.3

CH. SELECTOR

CH.2 CH.3

TRIGGER

+12V

IN

THROUGH

OUT

12V 0.1A

The unit

(rear)

Another

power

amplifier

Trigger Out

(+12 V)

TRIGGER

(IN/THROUGH OUT/OUT) jacks

System connection

input

Pre-amplifier

(such as

CX-A5000)

Subwoofer

Trigger In

(+12 V)

MX-A5000_om_UCTKABGLVF.book Page 9 Thursday, April 4, 2013 5:28 PM

10 En Advanced speaker configuration

Using a speaker that supports bi-amp connection

If you want to use a speaker that supports bi-amp connection to have more high-quality

sounds, change the CH. SELECTOR setting and connect the speaker to the

corresponding pair of the SPEAKERS terminals.

(Example)

Using a speaker that supports bi-amp connection for CH.2 (R)

By setting the CH. SELECTOR for CH.3 (R) to “CH.2”, CH.2 (R) input signals are output

from both the CH.2 (R) and CH.3 (R) speaker terminals. In this case, CH.3 (R) input is

not used.

Using two pairs of front speakers (SPEAKERS A/B)

If you connect two pairs of front speakers to the CH.2 A/B terminals, you can switch the

front speakers to be used by pressing SPEAKERS A/B on the front panel of the unit.

• When using two pairs of the speakers connected to the CH.2 A/B terminals at the same time, be sure to

use 8-ohm speakers and set IMPEDANCE SELECTOR to the upper position (p.7).

Using three speakers for one channel (multi-speaker)

If you want to use three speakers for reproducing CH.1 audio signals (such as center

channel signals), change the CH. SELECTOR setting and connect the speakers to the

CH.1 and CH.4 (L/R) terminals.

Advanced speaker configuration

Caution

• Remove the unit’s power cable from an AC wall outlet before making any connections or operating the

switches.

Caution

• Before making bi-amp connections, remove any brackets or cables that connect a woofer with a

tweeter. Refer to the instruction manual of the speakers for details. If you are not making bi-amp

connections, make sure that the brackets or cables are connected before connecting the speaker

cables.

R

SPEAKERS

TRIGGER

+12V

IN

THROUGH

OUT

BAL. UNBAL.

AUTO POWER

STANDBY

IMPEDANCE

SELECTOR

SELECTEUR

D’IMPEDANCE

OUT

OFF

ON

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

CH.1

12V 0.1A

R

BAL. UNBAL.

CH.2

R

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

R

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

CH

CH. S

E

CH.1

R

CH.3

CH. SELECTOR

CH.2 CH.3

The unit (rear)

Input from pre-amplifier

CH.2 A (R) and

CH.3 (R) terminals

Set CH. SELECTOR

for CH.3 (R) to “CH.2”

CH.2

B

CH.2

A

CH.2

B

CH.2

A

The unit (rear)

CH.2 A/B (L)

terminals

CH.2 A/B (R)

terminals

CH.4

CH.2

CH.4

BAL. UNBAL.

CH.1

R

CH.4

CH. SELECTOR

CH.1 CH.4

L

CH.4

CH. SELECTOR

CH.1 CH.4

The unit (rear)

Set CH. SELECTOR

for CH.4 (R) and

CH.4 (L) to “CH.1”

Input from pre-amplifier

CH.4 (R)

terminal

CH.4 (L)

terminal

CH.1

terminal

MX-A5000_om_UCTKABGLVF.book Page 10 Thursday, April 4, 2013 5:28 PM

Appendix En 11

Input-output signal path diagram

Appendix

BAL

UNBAL

SPEAKER A/B

B

A

CH.3

CH.2

CH.4

CH.1

CH.6

CH.5

CH.6

CH.5

CH.4

CH.3

CH.2

CH.1

UNBAL

BAL

UNBAL

BAL

UNBAL

BAL

UNBAL

BAL

UNBAL

BAL

UNBAL

BAL

CH.6

CH.5

CH.4

CH.1

CH.3

CH.2

CH.6

CH.5

CH.4

CH.3

SPEAKER A/B

B

A

CH.1

BAL

UNBAL

BAL

UNBAL

BAL

UNBAL

BAL

UNBAL

CH.2

B

CH.2

A

CH.2

B

CH.2

A

CH.6

CH.5

CH.4

CH.3

R

L

R

L

INPUT (RCA/XLR) jacks

BAL/UNBAL switch CH SELECTORCH SELECTOR BAL/UNBAL switch

SPEAKERS (L) terminals

SPEAKERS (R) terminals

MX-A5000_om_UCTKABGLVF.book Page 11 Thursday, April 4, 2013 5:28 PM

12 En Appendix

Troubleshooting

Refer to the table below when the unit does not function properly.

If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the unit, disconnect the power cable, and contact the nearest authorized

Yamaha dealer or service center.

First, check the followings:

a The power cables of the unit and other devices (such as a pre-amplifier) are connected to AC wall outlets securely.

b The unit and other devices (such as a pre-amplifier) are turned on.

c The connectors of each cable are securely inserted in to jacks on each device.

Problem Cause Remedy

The power does not turn on.

The protection circuitry has been activated three times

consecutively. When the unit is in this condition, the power

indicator on the unit blinks.

As a safety precaution, capability to turn on the power is disabled. Contact your

nearest Yamaha dealer or service center to request repair.

The internal microcomputer has frozen, due to an external electric

shock (such as lightning or excessive static electricity) or to a drop

in the power supply voltage.

Disconnect the power cable from the AC wall outlet and plug it again.

An external device is connected to the TRIGGER (IN) jack. Press down z (power) on the unit and then turn on the external device.

The power turns off (standby mode) immediately.

The unit was turned on while a speaker cable was shorted.

Twist the bare wires of each speaker cable firmly and reconnect to the unit and

speakers (p.7).

The unit was shorted because the speaker terminals come into

contact with metal parts of the AV rack, etc.

Keep enough space on the back of the unit (p.i).

The unit enters standby mode automatically.

The auto-standby function worked.

To disable the auto-standby function, set the AUTO POWER STANDBY switch to

“OFF” (p.8).

The protection circuitry has been activated because the volume of

the external device connected to the unit is too high.

Turn down the volume of the external device.

The protection circuitry has been activated because the

temperature inside of the unit is too high.

Install the unit in a well ventilated, place and allow enough ventilation space

around the unit (p.i).

No sound. The BAL/UNBAL switch setting is not correct. Change the BAL/UNBAL switch setting so that it matches the connections (p.6).

No sound is coming from a specific speaker.

The speakers connected to the CH.2 A/B terminals are turned off. Press SPEAKERS A/B to turn on the speakers (p.10).

The XLR balanced cable (or RCA unbalanced cable) connecting

the unit and pre-amplifier is defective, or the speaker cable

connecting the unit and speaker is defective.

If there is no problem with the connection, replace with another cable.

Another channel sound is coming from a specific

speaker.

The CH SELECTOR setting is not correct. Change the CH SELECTOR setting so that it matches your speaker system (p.10).

MX-A5000_om_UCTKABGLVF.book Page 12 Thursday, April 4, 2013 5:28 PM

Appendix En 13

Specifications

Input jacks

•Audio

Analog RCA (Unbalance) x 11

Analog XLR (Balance) x 11 (1:GND, 2:HOT, 3:COLD)

Output jacks

•Audio

Speaker Out x 11 ch

(13 Terminals: CH.1, CH.2-A [L/R], CH.2-B [L/R], CH.3 [L/R] to

CH.6 [L/R])

Other jacks

• TRIGGER OUT x 1 (+12 V/0.1 A max.)

• TRIGGER IN x 1 (+12 V In)

• TRIGGER THROUGH OUT x 1

Audio Section

• Rated Output Power (2-channel driven)

(20 Hz to 20 kHz, 0.06% THD, 6 )

CH.1................................................................................ 170 W

CH.2 (L/R)....................................................................... 170 W

CH.3 (L/R)....................................................................... 170 W

CH.4 (L/R)....................................................................... 170 W

CH.5 (L/R)....................................................................... 170 W

CH.6 (L/R)....................................................................... 170 W

(20 Hz to 20 kHz, 0.06% THD, 8 )

CH.1................................................................................ 150 W

CH.2 (L/R)....................................................................... 150 W

CH.3 (L/R)....................................................................... 150 W

CH.4 (L/R)....................................................................... 150 W

CH.5 (L/R)....................................................................... 150 W

CH.6 (L/R)....................................................................... 150 W

(1 kHz, 0.9% THD, 8 )

CH.1................................................................................ 170 W

CH.2 (L/R)....................................................................... 170 W

CH.3 (L/R)....................................................................... 170 W

CH.4 (L/R)....................................................................... 170 W

CH.5 (L/R)....................................................................... 170 W

CH.6 (L/R)....................................................................... 170 W

• Rated Output Power (1-channel driven)

(1 kHz, 0.9% THD, 6 )

CH.1 ...........................................................................230 W/ch

CH.2 (L/R) ..................................................................230 W/ch

CH.3 (L/R) ..................................................................230 W/ch

CH.4 (L/R) ..................................................................230 W/ch

CH.5 (L/R) ..................................................................230 W/ch

CH.6 (L/R) ..................................................................230 W/ch

(1 kHz, 0.9% THD, 8 )

CH.1 ...........................................................................190 W/ch

CH.2 (L/R) ..................................................................190 W/ch

CH.3 (L/R) ..................................................................190 W/ch

CH.4 (L/R) ..................................................................190 W/ch

CH.5 (L/R) ..................................................................190 W/ch

CH.6 (L/R) ..................................................................190 W/ch

(1 kHz, 0.9% THD, 4 )

CH.2 (L/R) [U.K. and Europe models]........................290 W/ch

• Maximum Effective Output Power (1-channel driven, JEITA)

[China, Taiwan, Korea and Asia models]

(1 kHz, 10% THD, 6 )

CH.1 ...........................................................................280 W/ch

CH.2 (L/R) ..................................................................280 W/ch

CH.3 (L/R) ..................................................................280 W/ch

CH.4 (L/R) ..................................................................280 W/ch

CH.5 (L/R) ..................................................................280 W/ch

CH.6 (L/R) ..................................................................280 W/ch

(1 kHz, 10% THD, 8 )

CH.1 ...........................................................................230 W/ch

CH.2 (L/R) ..................................................................230 W/ch

CH.3 (L/R) ..................................................................230 W/ch

CH.4 (L/R) ..................................................................230 W/ch

CH.5 (L/R) ..................................................................230 W/ch

CH.6 (L/R) ..................................................................230 W/ch

• Dynamic Power (IHF)

1-channel driven (8/6/4/2 ) ......................190/250/350/500 W

• Damping Factor

All Channels, 1 kHz, 8  ....................................... 180 or more

• Input Sensitivity / Input Impedance

Unbalance (1 kHz, 100 W/8 ).............................. 1.0 V/47 k

Balance (1 kHz, 100 W/8 ) .................................. 2.0 V/47 k

• Maximum Input Signal

Unbalance (1 kHz, 0.5% THD, 8 ).....................1.3 V or more

Balance (1 kHz, 0.5% THD, 8 ) .........................2.6 V or more

• Frequency Response (10 Hz to 100 kHz)................... +0/-3 dB

• Total Harmonic Distortion (70 W/8 ) ............... 0.015% or less

• Signal to Noise Ratio (IHF-A Network)

(Input Shorted 1 k, Reference Level 150 W/8 )

......................................................................... 116 dB or more

• Residual Noise (IHF-A Network)

Speaker Out (Input Shorted)................................ 60 µV or less

• Channel Separation (Input 5.1 k Shorted , 1 kHz/10 kHz)

...................................................................... 90/75 dB or more

• Gain...............................................................................29.1 dB

General

• Power Supply

[U.S.A. and Canada models]..........................AC 120 V, 60 Hz

[Taiwan model]................................ AC 110 to 120 V, 50/60 Hz

[China model] .................................................AC 220 V, 50 Hz

[Korea model] .................................................AC 220 V, 60 Hz

[Australia model].............................................AC 240 V, 50 Hz

[U.K. and Europe models] .............................. AC 230 V, 50 Hz

[Asia model]....................................AC 220 to 240 V, 50/60 Hz

• Power Consumption

[U.S.A. and Canada models]..............................650 W/850 VA

[Korea model] .................................................................550 W

[Other models]................................................................650 W

• Standby Power Consumption ........................... 0.1 W (Typical)

• Maximum Power Consumption (All Channel driven, 10% THD)

[Taiwan and Asia models].............................................1500 W

• Power Consumption (No Signals) ...................... 75 W (Typical)

• Dimensions (W x H x D)

...................435 x 210 x 463.5 mm (17-1/8” x 8-1/4” x 18-1/8”)

* Including legs and protrusions

• Weight ...........................................................25.4 kg (56.0 lbs)

* Specifications are subject to change without notice.

MX-A5000_om_UCTKABGLVF.fm Page 13 Wednesday, May 1, 2013 4:08 PM

i Fr

Précautions à prendre

Lisez le livret fourni « Brochure sur la sécurité » avant d’utiliser l’unité.

Installez l’unité dans un endroit propre, sec, frais et bien ventilé, où il ne risque pas

d’être exposé directement à la lumière du soleil, à la poussière, à l’humidité, au froid

et/ou soumis à des vibrations. Veillez à disposer de suffisamment d’espace pour

assurer une ventilation adéquate : au moins 30 cm au-dessus de l’unité, 20 cm sur

les côtés et 20 cm à l’arrière.

30 cm minimum

20 cm minimum

Étant donné que l’unité est dotée de bornes d’enceinte à surfaces métalliques nues,

veillez à laisser un espace suffisant à l’arrière de l’unité. Si les bornes d’enceinte

entrent en contact avec les parties métalliques du bâti AV, un court-circuit se produit

au niveau de l’unité, risquant d’endommager cette dernière.

Par ailleurs, ne touchez jamais les bornes d’enceinte lorsque l’unité est sous tension,

car cela pourrait provoquer un choc électrique.

L’unité n’est pas dotée de commandes de volume. Assurez-vous de raccorder à

l’unité un appareil doté d’une commande de volume (par exemple, un préamplificateur).

Si vous raccordez un appareil sans commande de volume (par exemple, un lecteur

CD) directement à l’unité, le volume risque d’être assourdissant et des dommages

peuvent survenir au niveau de l’unité ou des enceintes.

Faites attention aux

courts-circuits.

NE PAS TOUCHER !

(lorsque l’unité est sous tension)

MX-A5000_om_UCTKABGLVF.book Page i Friday, May 10, 2013 11:43 AM

Fr 1

TABLE DES MATIÈRES

Précautions à prendre . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i

Accessoires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Fonctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Noms de pièces et fonctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Panneau avant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Panneau arrière . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Raccordements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Raccordements des enceintes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Raccordement du câble d’alimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mise sous/hors tension de l’unité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Autres fonctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mise hors tension automatique de l’unité (fonction de mise en veille automatique) . . . . . . . . . . . . . . . . . . 8

Réglage de la luminosité du témoin d’alimentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Mise sous tension simultanée de l’unité et d’appareils externes (fonction de déclencheur) . . . . . . . . . . . . 9

Configuration d’enceinte avancée . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Utilisation d’enceintes prenant en charge les connexions bi-amplificatrices . . . . . . . . . . . . . . . . . . . . . . . . . 10

Utilisation de deux paires d’enceintes avant (SPEAKERS A/B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Utilisation de trois enceintes par voie (environnement multi-enceintes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Appendice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Diagramme de la trajectoire du signal d’entrée/sortie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Guide de dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Caractéristiques techniques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Accessoires

Vérifiez que les accessoires suivants sont fournis avec le produit.

 Câble d’alimentation

*Le câble d’alimentation fourni varie en fonction de la région d’achat.

 Câble de commande système

 Mode d’emploi

• En fonction des améliorations du produit, les caractéristiques techniques et illustrations peuvent être

modifiées sans préavis.

• signale les précautions à prendre concernant l’utilisation de l’unité et les limites de ses fonctions.

• signale des explications supplémentaires permettant une meilleure utilisation.

MX-A5000_om_UCTKABGLVF.book Page 1 Friday, May 10, 2013 11:43 AM

2 Fr Fonctions

Fonctions

Amplificateur de puissance haute

qualité

■ Amplificateur haute

puissance/haute qualité audio

(150 W x 11 voies)

L’unité est dotée d’un amplificateur de puissance 11 voies

muni d’une boucle de retour de courant Darlington à

trois niveaux, alimenté par un transformateur toroïdal

similaire à ceux utilisés dans les appareils audio Hi-Fi

haut de gamme. Les connecteurs d’enceinte plaqués or

sont également d’excellente qualité et produisent un

son d’une précision remarquable.

■ Prise en charge des connexions

symétriques et asymétriques

Des prises d’entrée symétriques (XLR) et asymétriques

(RCA) sont fournies sur toutes les voies et peuvent être

sélectionnées de manière indépendante pour chaque

voie.

Les connexions symétriques réduisent les bruits parasites

susceptibles d’être captés au niveau du raccordement

du câble entre l’unité et le préamplificateur, garantissant

ainsi une transmission haute fidélité du signal audio.

Les connexions asymétriques utilisent un détecteur au

sol pour obtenir une fidélité proche de la transmission

symétrique.

■ Structure de châssis exploitant

tout le potentiel de performances

de l’unité

Le châssis présente une structure spéciale permettant de

libérer tout le potentiel de l’amplificateur de puissance

haute qualité.

• Conception d’amplificateur de puissance symétrique

• Panneaux avant et latéraux en aluminium

• Pieds extrêmement stables utilisant la technologie A.R.T.

(Anti-Resonance Technology, technologie antirésonance)

Évolutivité pour répondre à divers besoins

■ Liberté de positionnement des

enceintes

Étant donné que les 11 voies sont dotées d’amplificateurs

de puissance partageant les mêmes caractéristiques

techniques, l’unité permet non seulement de configurer

un Home Cinéma 11 voies maximum mais aussi des

systèmes multipièces ou d’autres combinaisons

d’enceintes selon vos besoins.

■ Prise en charge de connexions

bi-amplificatrices et de la lecture

multi-enceintes

Grâce à la fonction de sélecteur de voies dont est dotée

l’unité, vous pouvez utiliser des connexions

bi-amplificatrices ou multi-enceintes sans avoir à

raccorder des câbles supplémentaires au niveau de

votre préamplificateur. Par exemple, l’entrée audio CH.2

peut être émise par les sorties des enceintes CH.2 et

CH.3 pour former une configuration bi-amplificatrice et

transmettre un son haute qualité, ou bien l’entrée CH.1

(mono) peut être émise par trois enceintes raccordées à

CH.1 et CH.4 (L/R).

■ Mise sous/hors tension de l’unité

depuis votre préamplificateur

(fonction de déclencheur)

La mise sous/hors tension de l’unité peut se faire de

manière synchronisée avec le dispositif de mise

sous/hors tension d’un autre appareil prenant en charge

la fonction de déclencheur, par exemple, un préampli

audio-vidéo (TRIGGER IN). Le signal d’entrée de la

prise TRIGGER IN peut également être restitué sans

dégradation dans un raccordement en cascade pour

mettre sous/hors tension un autre appareil, par exemple

un subwoofer Yamaha (THROUGH OUT). De plus, la

mise sous/hors tension d’un appareil externe peut se

faire de manière synchronisée avec la mise sous/hors

tension de l’unité (TRIGGER OUT), ce qui vous permet

de configurer plusieurs systèmes avec commutation

d’alimentation synchronisée.

Préamplificateur

MX-A5000_om_UCTKABGLVF.book Page 2 Friday, May 10, 2013 11:43 AM

Noms de pièces et fonctions Fr 3

Panneau avant

1 Bouton z (alimentation)

Met l’unité sous ou hors tension (veille) (p.8).

2 Témoin d’alimentation

S’allume lorsque l’unité est mise sous tension.

Si le témoin clignote, cela indique que le circuit de protection

a été activé. Pour plus d’informations, reportez-vous à la

section « Guide de dépannage » (p.12).

• Vous pouvez varier la luminosité du témoin d’alimentation (p.8).

3 Boutons SPEAKERS A/B

Activent/désactivent les enceintes raccordées aux bornes

CH.2 A/B (p.10).

• Les deux enceintes (A et B) sont désactivées par défaut.

Appuyez sur le bouton pour activer les enceintes que vous

souhaitez utiliser.

• Lorsque vous utilisez simultanément deux paires d’enceintes

raccordées aux bornes CH.2 A/B, veillez à utiliser des enceintes

8 ohms et à placer le IMPEDANCE SELECTOR en position

haute (p.7).

Noms de pièces et fonctions

SPEAKERS

ON OFF

AB

21

3

MX-A5000_om_UCTKABGLVF.book Page 3 Friday, May 10, 2013 11:43 AM

4 Fr Noms de pièces et fonctions

Panneau arrière

1 Bornes SPEAKERS

Pour le raccordement à des enceintes (p.7).

2 Prises TRIGGER

Pour le raccordement à des appareils prenant en charge la

fonction de déclencheur (p.9).

3 Commutateur AUTO POWER STANDBY

Active/désactive la fonction de mise en veille automatique

(p.8).

4 IMPEDANCE SELECTOR

Change le réglage de l’impédance d’enceinte de l’unité en

fonction des enceintes raccordées (p.7).

5 Prise AC IN

Pour raccorder le câble d’alimentation fourni (p.8).

6 CH. SELECTOR

(CH.3, CH.4 et CH.6 uniquement)

Sélectionne la source d’entrée audio de l’amplificateur CH.3,

CH.4 ou CH.6 lors de l’utilisation d’une connexion

bi-amplificatrice (p.10) ou multi-enceintes (p.10).

AC IN

R

SPEAKERS

TRIGGER

INPUT

+12V

IN

THROUGH

OUT

BAL. UNBAL.

AUTO POWER

STANDBY

IMPEDANCE

SELECTOR

SELECTEUR

D’IMPEDANCE

OUT

OFF

ON

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

CH.1

L

SPEAKERS

CH.6

CH.5

CH.4

CH.3

CH.2

B

CH.2

A

12V 0.1A

R

BAL. UNBAL.

CH.2

BAL. UNBAL.

CH.1

L

BAL. UNBAL.

CH.2

L

BAL. UNBAL.

CH.5

R

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

R

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

R

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.4

CH. SELECTOR

CH.1 CH.4

L

BAL. UNBAL.

CH.3

CH. SELECTOR

CH.2 CH.3

L

BAL. UNBAL.

CH.6

CH. SELECTOR

CH.5 CH.6

BAL. UNBAL.

CH. SELECTOR

3

4 5

6

7

8

9

11 2

Attention

• Débranchez le câble d’alimentation de l’unité de la prise

secteur avant d’effectuer un raccordement ou d’utiliser les

commutateurs et/ou sélecteurs.

MX-A5000_om_UCTKABGLVF.book Page 4 Friday, May 10, 2013 11:43 AM

Sayfa yükleniyor ...

Yamaha MX-A5000 El kitabı

Yamaha MX-A5000 El kitabı

Diğer dillerde

İlgili Makaleler