Electrolux EW1220N Kullanım kılavuzu

Marka: Electrolux

Model: EW1220N

Kategori: Çamaşır makineleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

EW1620N

INSTRUCTION BOOKLET

KULLANIM KILAVUZU

WASHING MACHINE

ÇAMAÇIR MAKINESI

132 993 580

EW 1220N

EW 1620N

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 1

Dear customer,

Please read these operating instructions carefully

and pay particular attention to the safety notes

indicated in the first pages. We recommend that you

keep this instruction booklet for future reference and

pass it on to any future owners.

Transport damages

When unpacking the appliance, check that it is not

damaged. If in doubt, do not use it and contact the

Service Centre.

The symbols you will see on some paragraphs of this booklet have the following meaning:

The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly

important for your safety or correct functioning of the appliance.

The information marked with this symbol provides additional instructions and practical tips on the use of

the appliance.

Tips and information about economical and ecological use of the machine are marked with this symbol.

Our contribution to the protection of the

environment: we use environmentally

friendly paper.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 2

ENGLISH

Contents

Use 10

Control panel 10

Controls 10-13

Washing hints 14

Sorting the laundry 14

Temperatures 14

Before loading the laundry 14

Maximum loads 14

Laundry weights 14

Removing stains 14

Detergents and additives 15

“Jet System” wash 15

Operating sequence 16-18

Washing programmes 19

International wash code symbols 20

Cleaning and maintenance 21-22

Bodywork 21

After each wash 21

Detergent dispenser drawer 21

Drain filter 21

Water inlet filter 22

Emergency emptying out 22

The dangers of freezing 22

Something not working? 23-24

Warnings 4

Disposal 5

Tips for environmental protection 5

Technical specifications 6

Installation 7

Unpacking 7

Positioning 7

Water inlet 7

Water drainage 8

Electrical connection 8

Your new washing machine 9

Description of the appliance 9

Door locked pilot light 9

Detergent dispenser drawer 9

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 3

General safety

• Repairs to the machine must be carried out only by

qualified personnel. Repairs carried out by

inexperienced persons could cause serious

danger. Contact your local Service Centre.

• Never start the machine if the electrical supply

cable is damaged or the control panel or worktop

are so damaged that inner components can be

reached.

• Unplug the appliance before carrying out any

cleaning or maintenance operations.

• Never pull the power supply cable to remove the

plug from the socket; always take hold of the plug

itself.

• Never spray the machine with a jet of water.

Danger of electric shock!

• During high temperature wash programmes the

door glass may get hot. Do not touch it!

• Let the water cool down before carrying out

emergency emptying or before opening the door in

an emergency.

• Small animals can gnaw electric wires and water

hoses causing electrocution hazard and damage

due to water leaks.

Positioning, connection, starting up

• Follow the instructions for positioning and

connection.

• Carry out a first wash without laundry (COTTONS

60, with half the amount of detergent) in order to

remove any manufacturing residue from the tub

and the drum.

• Should the machine be purchased in winter, when

temperatures can be below 0°, leave the appliance

for 24 hours at ambient temperature before starting it.

Proper use

• This appliance is designed for domestic use only. If

the machine is used for any other purposes or is

not used correctly, the manufacturer accepts no

responsibility for any damage that might occur.

• For safety reasons, the appliance must not be

modified.

• Use only detergents suitable for washing machines

and follow the manufacturer’s instructions.

• Garments which have been in contact with

flammable solvents should not be machine washed.

Warnings

• Do not use your machine for dry cleaning.

• Dyes and bleaching agents may only be used if

specifically permitted by the manufacturer of these

products. We cannot be held responsible for any

damage.

• Always unplug the appliance and turn off the water

tap after use.

Child safety

• Children are often not aware of how dangerous

electrical appliances can be. When the machine is

working, children should be carefully supervised

and not be allowed to play with the appliance -

there is a risk that they could become trapped

inside.

• The packaging components (e.g. plastic film,

polystyrene) can be dangerous to children - danger

of suffocation! Keep them out of children’s reach.

• Keep all detergents in a safe place out of children’s

reach.

• When the appliance is to be scrapped, cut off the

electrical supply cable and destroy the plug with

the remaining cable. Disable the door catch in

order to prevent children from becoming trapped

inside while playing.

Child safety feature

• This machine incorporates a special child safety

feature to prevent small children from being

trapped inside the machine.

To activate this device, rotate the button (without

pressing it) inside the door clockwise until the

groove is horizontal. If necessary use a coin. To

disable this device and restore the possibility of

closing the door, rotate the button anti-clockwise

until the groove is vertical.

P1076

The following warnings are provided in the interests of overall safety. You must read them carefully before

installing or using the appliance.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 4

ENGLISH

Disposal

Tips for environmental protection

Packaging materials

The materials marked with the symbol are

recyclable.

>PE<=polyethylene

>PS<=polystyrene

>PP<=polypropylene

This means that they can be recycled by disposing of

them properly in appropriate collection containers.

Machine

Use authorised disposal sites for your old appliance.

Help to keep your country tidy!

To save water, energy and to help protect the

environment, we recommend that you follow these

tips:

• Normally soiled laundry may be washed without

prewashing in order to save detergent, water and

time (the environment is protected too!).

• The machine works more economically if it is fully

loaded.

• With adequate pre-treatment, stains and limited

soiling can be removed; the laundry can then be

washed at a lower temperature.

• Measure out detergent according to the water

hardness, the degree of soiling and the quantity of

laundry being washed.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 5

DIMENSIONS Height 85 cm

Width 60 cm

Depth 62 cm

MAXIMUM LOAD Cotton 5.0 kg

Synthetics 2,5 kg

Delicates 2,5 kg

Woollens / Hand wash 2 kg

SPIN SPEED 1200 rpm max. (EW 1200N)

1600 rpm max. (EW 1600N)

POWER SUPPLY VOLTAGE/FREQUENCY 220-230 V/50 Hz

TOTAL POWER ABSORBED 2200 W

MINIMUM FUSE PROTECTION 10 A

WATER PRESSURE Minimum 500 kPa

Maximum 800 kPa

This appliance complies with the following EEC Directives:

73/23/EEC of 19/02/73 relating to low voltage

89/336/EEC of 03/05/89 relating to electromagnetic compatibility.

Technical specifications

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 6

ENGLISH

Installation

Unpacking

All transit bolts and packing must be removed

before using the appliance.

You are advised to keep all transit devices so that

they can be refitted if the machine ever has to be

transported again.

1. Using a spanner, unscrew and remove the two

rear bottom screws. Slide out the two plastic pins.

2. Lay the machine on its back, taking care not to

squash the hoses. This can be avoided by

placing one of the corner packing pieces between

the machine and the floor.

3. Remove the polystyrene block from the bottom of

the machine and release the two plastic bags.

4. Very carefully slide out the left polythene bag,

removing it towards the right and then downwards.

5. Very carefully slide out the right polythene bag,

removing it towards the left and then upwards.

6. Set the machine upright and remove the

remaining rear screw from the back. Slide out

the relevant pin.

P0001

7. Plug the open holes with the plugs which are

supplied with the instruction booklet.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is

not impeded by carpets, rugs etc. Check that the

machine does not touch the wall or other kitchen

units.

Carefully level by screwing the adjustable feet in or

out. Never place cardboard, wood or similar

materials under the machine to compensate for any

unevenness in the floor.

Water inlet

Connect the water inlet hose to a tap with a 3/4" thread.

The other end of the inlet hose which connects to the

machine can be turned in any direction. Simply

loosen the fitting, rotate the hose and retighten the

fitting, making sure there are no water leaks.

The inlet hose must not be lengthened. If it is too

short and you do not wish to move the tap, you will

have to purchase a new, longer hose specially

designed for this type of use.

P0021

P1088

P1051

P0002

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 7

Water drainage

The end of the drain hose can be positioned in three

ways:

Hooked over the edge of a sink using the plastic

hose guide supplied with the machine. In this

case, make sure the end cannot come unhooked

when the machine is emptying.

This could be done by tying it to the tap with a piece

of string or attaching it to the wall.

In a sink drain pipe branch. This branch must be

above the trap so that the bend is at least 60 cm

above the ground.

Directly into a drain pipe at a height of not less

than 60 cm and not more than 90 cm.

The end of the drain hose must always be

ventilated, i.e. the inside diameter of the drain pipe

must be larger than the outside diameter of the drain

hose.

The drain hose must not be kinked. Run it along the

floor; only the part near the drainage point must be

raised.

P0023

P0022

Electrical connection

This machine is designed to operate on a 220-230 V,

single-phase, 50 Hz supply.

Check that your domestic electrical installation can

take the maximum load required (2.2 kW), also

taking into account any other appliances in use.

Connect the machine to an earthed socket.

The manufacturer declines any responsibility

for damage or injury through failure to comply

with the above safety precaution.

Should the appliance power supply cable

need to be replaced, this should be carried

out by our Service Centre.

The power supply cable must be easily

accessible after installing the machine.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 8

ENGLISH

Your new washing machine

This new machine, which is fitted with the Direct Spray system, patented Electrolux, meets all modern needs

for effective treatment of laundry with low water, energy and detergent consumption.

Further savings are achieved by washing small loads of laundry, since water and electricity consumption is

proportional to the quantity and type of laundry being washed.

• Selection of the programme and temperature by means of the relevant buttons.

• The programme phase indicator shows the wash cycle progress.

• The programme progress display shows the programme steps selected and the programme phase which

is running.

• The Delay Start option allows you to delay starting of the wash programme to the desired time of day.

• The Anticrease function (stop with water in drum) can be selected for all fabrics: the laundry is left

immersed in the final rinse water to avoid the formation of creases.

• The special wool programme with its new delicate wash system treats your woollens with extreme care.

• 3-compartment drawer for detergent and fabric softener.

• The balance control device ensures the machine is stable during the spin.

1 Detergent dispenser drawer

2 Control panel

3 Door locked light

4 Door opening handle

5 Drain filter

6 Adjustable feet

Door locked light

It stays on during the whole programme indicating

that the door is locked.

When the light goes out, the door can be opened

(see page 13).

Detergent dispenser drawer

Prewash

Main wash

Fabric softener, starch

Description of the appliance

C0063

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 9

Use

Control panel

1 ON/OFF button (Açma/Kapama)

Press this button to switch the washing machine on.

The display (8) will show three blinking dashes or a

blinking zero. You will find more detailed

explanations on pages 11-12 (see “DISPLAY”).

Press the ON/OFF button again to switch the

machine off.

2 Mains-on light

This light is connected to the ON/OFF button. It lights

up when you press the button, and goes out when

you press it again.

3 FABRIC button (Çamaçır)

Press this button repeatedly to select the programme

on the basis of the type of laundry to be washed. The

light relevant to the selected programme will light up.

The washing machine will propose a temperature

and automatically select the maximum spin value

provided for the programme you have chosen.

You can change these values by operating buttons

4 and 5.

Hand wash (Elde Yıkananlar)

When you select this programme, you obtain a

particularly delicate washing, suitable for articles of

clothing whose label indicates that they must be

hand-washed .

4 TEMPERATURE button (Sıcaklık)

Press this button repeatedly to increase or decrease

the temperature, if you want your laundry to be

washed at a temperature different from the one

proposed by the washing machine. The relevant light

will light up.

Maximum temperatures are 95°C for cotton, 60°C for

synthetic fabrics, 40°C for delicate fabrics, wool and

fabrics to be hand-washed (HAND WASH

programme).

Position SOGUK corresponds to a COLD WASH.

This option can be used for very delicate laundry,

such as curtains.

Important!

By depressing TEMPERATURE and SPIN SPEED

buttons simultaneously, the acoustic signal at the

end of the cycle is suppressed.

5 SPIN SPEED button (DEVIR)

Press this button repeatedly to change the spin

speed, if you want your laundry to be spun at a

speed different from the one proposed by the

washing machine. The relevant light will light up.

Maximum speeds are:

• for cotton: 1,600 rpm (EW 1620N)

1,200 rpm (EW 1220N);

• for synthetic fabrics, wool, and fabrics to be hand-

washed: 900 rpm;

• for delicate fabrics: 700 rpm.

RINSE HOLD position (SUDA BEKLETME): when

you choose this option, the machine will not drain the

water of the last rinse, so as not to wrinkle the

laundry.

At the end of the cycle, the light of the

START/PAUSE button (BAÇLAT/BEKLET) will flash,

to indicate that the water must be drained.

To complete the cycle, choose one of the following

options:

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 10

ENGLISH

• Draining and spin:

- Press the START/PAUSE button. The machine will

drain the water, then spin the laundry at the maximum

speed provided for the performed programme.

- Select spin speed by means of button 5, and

press the START/PAUSE button.

• Drain only

- Press the SKIP/RESET button (ILERLETME/IPTAL)

once, so as to cause the DRAIN light (BOÇALTMA)

to light up, then press the START/PAUSE button.

Important!

If you accidentally press the SKIP/RESET button

more than once, the display will show three blinking

dashes. To cause the washing machine to drain the

water, select any washing programme by means of

the FABRIC button, then press SKIP/RESET three

times in order to select the DRAIN position (only the

DRAIN light will remain lit).

6 OPTIONS button (SEÇENEKLER)

Press this button to select the following options:

• PREWASH (ÖN YIKAMA): select this option if you

wish your laundry to be prewashed before the main

wash (not available for wool and hand-wash cycle).

The prewash ends with a short spin at 650 rpm in

programmes for cotton and synthetic fabrics,

whereas in the programme for delicate fabrics the

water is only drained.

• SUPER RINSE (EKSTRA DURULAMA): this

option can be selected with all programmes except

the wool programme and hand wash. The

machine performs 4 rinses instead of 3. This option

is recommended for people who are allergic to

detergents, and in areas where the water is very soft.

7 QUICK WASH (HIZLI YIKAMA)

This button allows you to select the QUICK WASH

function, for laundry that is only slightly soiled (not

for wool and HAND WASH programme).

The washing time will be reduced according to the

type of fabric and the selected temperature.

8 Display

The following pieces of information are shown on the

display:

• Three blinking dashes, when a programme is

cancelled by means of the SKIP/RESET

(BAÇLAT/BEKLET) button.

The three blinking dashes will also appear when you

press the ON/OFF (AÇMA KAPAMA) button to

switch the machine on, if the previously selected

cycle has been erased.

•

Duration of washing programme in hours and

minutes, after you have selected a programme.

While the programme is running (after you have

pressed the START/PAUSE button

BAÇLAT/BEKLET), the displayed time value

decreases by one unit every minute.

• The washing machine has stopped with water in

the tub, at the end of a programme with the RINSE

HOLD (SUDA BEKLETME) option: this is indicated

by a static zero.

• The washing machine has completed the

programme: this is indicated by a blinking zero. At

the same time, the door locked light goes out. The

zero will reappear when you switch the washing

machine on, unless the previous programme has

been erased by means of the SKIP RESET

(ILERLETME/IPTAL) button.

Important!

The first time you use the washing machine,

when you switch it on, it may display a blinking zero

and give an audible warning signal. This is due to the

fact that the washing machine has performed a

washing cycle during the manufacturer’s inspection

2.05

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 11

tests, and this cycle has not been erased after its

completion.

• Delay start, a time value indicated in hours and

selected by means of the relevant button

(GECIKTIRME).

The delay time is displayed for 5 seconds, then the

duration of the selected programme reappears.

After you have pressed the START/PAUSE button,

the countdown begins, and the delay time value

decreases by one unit every hour.

You can delay the start of the selected programme

by up to 24 hours in one hour intervals.

• An incorrect option selection has been made:

this is indicated by the message Err when a function

incompatible with the current programme is selected.

The incorrect selection is also indicated by an

audible warning signal.

• An alarm code indicates a fault in the machine

operation (see the relevant chapter on page 23).

9 START/PAUSE button

(Baçlat/Beklet)

This button has three functions:

• Start: after you have selected the desired

programme and options, press this button to start the

washing machine. The light above the button will

stop flashing and remain lit.

If you have selected a delay time by means of

button L, the countdown will begin and will be shown

on the display.

• Pause: when you press this button again, the

programme in progress is interrupted. The light

above the button will start flashing. To restart the

programme, press the button again.

When you PAUSE the cycle, the DOOR LOCKED

light goes out, and it becomes possible to open the

door, provided

• the washing machine is not in the heating phase;

• the level of the water is not high;

• the drum is not turning.

Important!

You must set the washing machine to PAUSE before

you make any change in the programme in progress.

• Draining of water and spinning after the

execution of programmes with the RINSE HOLD

(SUDA BEKETME) option.

10 SKIP/RESET button

(ILERLETME/IPTAL)

At the end of a programme, you must press this

button once or repeatedly, in order to clear the

contents of the memory (the display will show three

blinking dashes); otherwise, the next time you switch

the washing machine on, the blinking zero will

reappear and the audible warning signals relevant to

the end of the previous cycle will be given.

You can also press the SKIP/RESET button to

exclude one or several phases of the programme

which is running, as indicated below.

- set the washing machine to PAUSE by pressing the

START/PAUSE button (the relevant light will flash);

- press the SKIP/RESET button once or several

times, until the required phase(s) is(are) cancelled

(the light next to the name of the phase(s) will go

out).

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 12

ENGLISH

Example:

In this case, both the

drain and the spin (at

the speed provided for

the selected type of

fabric) will be

performed.

This button allows you also to select special

programmes, such as RINSES, SPIN and DRAIN.

• If the machine is already switched on because it

has just performed a washing programme, proceed

as follows:

- depress SKIP/RESET once or repeatidly to cancel

the previously performed programme;

- select the type of fabric by means of button

“ÇAMASIR”;

- select the special programme:

• RINSES (DURULAMA)

Depress SKIP/RESET once, the pilot light YIKAMA

(WASH) goes out.

• SPIN (SIKMA)

Depress SKIP/RESET twice, the pilot lights

YIKAMA (WASH) and DURULAMA (RINSES) go

out.

• DRAIN (BOÇALTMA)

Depress SKIP/RESET three times, the pilot lights

YIKAMA (WASH), DURULAMA (RINSES) and

SIKMA (SPIN) go out.

Example:

In this case the machine

will perform the rinses

followed by the spin.

• If the machine is switched off:

- depress ON/OFF (AÇMA/KAPAMA) button to

switch it on;

- select the type of fabric by means of button

“ÇAMAÇIR”;

- select the special programme as previously described.

PREWASH

ÖN YIKAMA

WASH

YIKAMA

RINSES

DURULAMA

SPIN

SIKMA

DRAIN

BOSALTMA

PREWASH

ÖN YIKAMA

WASH

YIKAMA

RINSES

DURULAMA

SPIN

SIKMA

DRAIN

BOSALTMA

11 DELAY START button

(GECIKTIRME)

This button makes it possible to delay the starting of

the programme by up to 24 hours. The delay you

have selected is shown on the display for about 5

seconds; afterwards, the duration of the programme

reappears.

You must select this option after you have set the

programme and before you press the

START/PAUSE button.

The time value shown on the display will decrease

by one unit every hour.

You can change the delay time at any moment,

before you press the START/PAUSE button.

If you have already pressed the START/PAUSE

button, and you wish to change or cancel the delay

time, proceed as follows:

• set the washing machine to PAUSE by pressing the

START/PAUSE button;

• press the DELAY button until the display shows the

desired delay time or

• press the DELAY button once, to erase the delay

time. The display will indicate “0h”.

• press the START/PAUSE button again.

Important!

The door will be locked throughout the delay time

(DOOR LOCKED light lit).

If you need to open the door, you must first set the

washing machine to PAUSE by pressing the

START/PAUSE button. After you have closed the

door, press the START/PAUSE button again.

12 Programme phase indicator lights

When you select a programme, the lights relevant to

the phases that form the programme light up.

After you have started

the programme, only

the light relevant to

the phase that is

currently being carried

out will remain lit.

PREWASH

ÖN YIKAMA

WASH

YIKAMA

RINSES

DURULAMA

SPIN

SIKMA

DRAIN

BOSALTMA

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 13

Washing hints

Sorting the laundry

Follow the wash code symbols on each garment

label and the manufacturer’s washing instructions.

Sort the laundry as follows:

whites, coloureds, synthetics, delicates, woollens.

Temperatures

95° for normally soiled white cottons and linen

(e.g. tea cloths, towels, tablecloths,

sheets...)

60° for normally soiled, colour fast garments

(e.g. shirts, night dresses, pyjamas....) in

linen, cotton or synthetic fibres and for

lightly soiled white cotton (e.g. underwear).

(cold)for delicate items (e.g. net curtains), mixed

30°-40° laundry including synthetic fibres and

woollens.

Before loading the laundry

Never wash whites and coloureds together. Whites

may lose their “whiteness” in the wash.

New coloured items may run in the first wash; they

should therefore be washed separately the first time.

Make sure that no metal objects are left in the

laundry (e.g. hair clips, safety pins, pins).

Button up pillowcases, close zip fasteners, hooks

and poppers. Tie any belts or long tapes.

Remove persistent stains before washing. Rub

particularly soiled areas with a special detergent or

detergent paste.

Treat curtains with special care. Remove hooks or tie

them up in a bag or net.

Maximum loads

Recommended loads are indicated in the

programme charts.

General rules:

Cotton, linen: drum full but not too tightly packed;

Synthetics: drum no more than half full;

Delicate fabrics and woollens: drum no more than

one third full.

Washing a maximum load makes the most efficient

use of water and energy.

For heavily soiled laundry, reduce the load size.

Laundry weights

The following weights are indicative:

bathrobe 1200 g

napkin 100 g

quilt cover 700 g

sheet 500 g

pillow case 200 g

tablecloth 250 g

towelling towel 200 g

tea cloth 100 g

night dress 200 g

ladies’ briefs 100 g

man’s work shirt 600 g

man’s shirt 200 g

man’s pyjamas 500 g

blouse 100 g

men’s underpants 100 g

Removing stains

Stubborn stains may not be removed by just water

and detergent. It is therefore advisable to treat them

prior to washing.

Blood: treat fresh stains with cold water. For dried

stains, soak overnight in water with a special

detergent then rub in the soap and water.

Oil based paint: moisten with benzine stain

remover, lay the garment on a soft cloth and dab the

stain; treat several times.

Dried grease stains: moisten with turpentine, lay

the garment on a soft surface and dab the stain with

the fingertips and a cotton cloth.

Rust: oxalic acid dissolved in hot water or a rust

removing product used cold. Be careful with rust

stains which are not recent since the cellulose

structure will already have been damaged and the

fabric tends to hole.

Mould stains: treat with bleach, rinse well (whites

and fast coloureds only).

Grass: soap lightly and treat with bleach (whites and

fast coloureds only).

Ball point pen and glue: moisten with acetone (*),

lay the garment on a soft cloth and dab the stain.

Lipstick: moisten with acetone as above, then treat

stains with methylated spirits. Remove any residual

marks from white fabrics with bleach.

Red wine: soak in water and detergent, rinse and

treat with acetic or citric acid, then rinse. Treat any

residual marks with bleach.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 14

ENGLISH

Quantity of detergent to be used

The type and quantity of detergent will depend on

the type of fabric, load size, degree of soiling and

hardness of the water used.

Water hardness is classified in so-called “degrees” of

hardness. Information on hardness of the water in

your area can be obtained from the relevant water

supply company, or from your local authority.

Follow the product manufacturers’ instructions on

quantities to use.

Use less detergent if:

– you are washing a small load,

– the laundry is lightly soiled,

– large amounts of foam form during washing.

Degrees of water hardness

«JETSYSTEM» wash

As the Jetsystem is flexible and adjusts water intake

according to wash load size it is not possible to give

you exact recommendations as to the amount of

detergent that should be used for any one wash.

Therefore we recommend that you use

approximately 1/3 less than the detergent

manufacturer recommends on the packet or bottle,

making the appropriate allowances for soft or hard

water, and light or heavy soilage of clothes. If you

have judged the amount correctly you should expect

to see a soft sudsy liquid during the wash. It is not

necessary to have a head of lather on the water.

Ink: depending on the type of ink, moisten the fabric

first with acetone (*), then with acetic acid; treat any

residual marks on white fabrics with bleach and then

rinse thoroughly.

Tar stains: first treat with stain remover, methylated

spirits or benzine, then rub with detergent paste.

(*) do not use acetone on artificial silk.

Detergents and additives

Good washing results also depend on the choice of

detergent and use of the correct quantities to avoid

waste and protect the environment. Although

biodegradable, detergents contain substances

which, in large quantities, can upset the delicate

balance of nature.

The choice of detergent will depend on the type of

fabric (delicates, woollens, cottons, etc.), the colour,

washing temperature and degree of soiling.

All commonly available washing machine detergents

may be used in this appliance:

– powder detergents for all types of fabric,

– powder detergents for delicate fabrics (60°C max)

and woollens,

– liquid detergents, preferably for low temperature

wash programmes (60°C max) for all types of

fabric, or special for woollens only.

The detergent and any additives must be placed in

the appropriate compartments of the dispenser

drawer before starting the wash programme.

If using concentrated powder or liquid detergents, a

programme without prewash must be selected.

The washing machine incorporates a recirculation

system which allows an optimal use of the

concentrated detergent.

Pour liquid detergent into the dispenser drawer

compartment marked just before starting the

programme.

Any fabric softener or starching additives must be

poured into the compartment marked before

starting the wash programme.

Follow the product manufacturer’s recommendations

on quantities to use and do not exceed the «MAX»

mark in the detergent dispenser drawer.

Level Characteristic

Degrees

German

°dH

French

°T.H.

soft

medium

hard

very hard

0- 7

8-14

15-21

more than

0-15

16-25

26-37

more than

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 15

4. Switch the machine on

Press the ON/OFF button (AÇMA KAPAMA) to

switch the machine on. The display will show three

blinking dashes or a blinking zero. The light above

the button will light up.

5 Select the desired

programme/fabric

Press the FABRIC button (ÇAMAÇIR) repeatedly, in

order to select the desired programme/fabric. The

relevant light will light up.

The lights relevant to the phases that form the

programme will light up.

The display will show the duration of the selected

programme, calculated on the basis of the maximum

load for each type of fabric. The light of

START/PAUSE button will start flashing.

If the load of laundry to be washed is small, at the

beginning of the cycle the display will still indicate the

duration relevant to the maximum load. The duration

value will be gradually adjusted during the execution

of the cycle.

PREWASH

ÖN YIKAMA

WASH

YIKAMA

RINSES

DURULAMA

SPIN

SIKMA

DRAIN

BOSALTMA

Operating sequence

Before washing your first load of laundry, we

recommend that you run a cotton cycle at 60°C, with

the machine empty, in order to remove any

manufacturing residue from the drum and tub.

Pour half a measure of detergent into the main wash

compartment and start up the machine.

1. Place the laundry in the drum

Open the door.

Place the laundry in the drum, one item at a time,

shaking them out as much as possible.

Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops. Measure

out the amount of detergent recommended by the

manufacturer in a graduated cup and pour it into the

main wash compartment .

If you wish to carry out the prewash, pour detergent

into the appropriate compartment marked .

3. Measure out the additive

If required, pour fabric softener into the compartment

marked , without exceeding the «MAX» mark.

C0065

C0064

P1084

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 16

ENGLISH

9 Select the QUICK WASH option

(HIZLI YIKAMA)

Depress button HIZLI YIKAMA to select the QUICK

WASH option, if your laundry is only slightly soiled.

The relevant light illuminates.

10 Select the DELAY TIME

Before you start the programme, if you wish the

starting to be delayed, press the DELAY button

GECIKTIRME repeatedly, or keep it pressed, to

select the desired delay. The selected delay time

value (up to 24 hours) will appear on the display for 5

seconds, then the duration of the programme will

appear again.

11 Start the programme

Press the START/PAUSE button . The relevant

light will stop flashing, the DOOR LOCKED light will

light up, and only the light relevant to the phase that

is in progress will remain lit.

If you have chosen a delayed start, the washing

machine will begin the countdown.

The display will show the duration of the programme

or the selected delay.

6 Select the temperature

Press the TEMPERATURE button SICAKLIK if you

wish to select a temperature value different from the

one proposed by the washing machine or the COLD

WASH “SOGUK”.

The relevant light will light up.

7 Select the SPIN SPEED or the RINSE

HOLD option (SUDA BEKLETME)

Press the SPIN SPEED button “DEVIR” repeatedly, in

order to select the desired spin speed or the RINSE

HOLD (SUDA BEKLETME) option. The relevant light

will light up.

If you select the RINSE HOLD option, the machine

will stop at the end of the programme with the water

still in the tub.

8 Select the desired options

If your laundry is very dirty, it may be advisable to

select the PREWASH option “ÖN YIKAMA”.

If you wish the laundry to undergo an extra rinse,

select the super rinse option “EKSTRA

DURULAMA”.

Press the OPTIONS button “SEÇENEKLER” so as to

cause one or both of the lights to light up.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 17

12 How to change a programme

during its cycle

Before you make any change, you must pause the

washing machine by pressing the START/PAUSE

button.

It is possible to change any phase before the

programme carries it out.

Changing the type of fabric or temperature is

possible, obviously, only during the washing phase.

When you make a change in these two parameters,

the washing machine will resume the cycle from the

beginning.

If it is necessary to drain the water in order to change

the programme in progress, proceed as follows:

• PAUSE the machine by pressing the

START/PAUSE button;

• press the SKIP/RESET button

(ILERLETME/IPTAL) repeatedly, until only the

DRAIN light (BOÇALTMA) remains lit;

• press the START/PAUSE button again.

When the water has been drained, the display shows

a blinking zero. You may now select a new

programme and press the START/PAUSE button to

start it.

13 How to cancel a programme

during its cycle

To cancel a programme that is being carried out, first

pause the washing machine by pressing the

START/PAUSE button , then press the

SKIP/RESET button (ILERLETME/IPTAL) repeatedly,

until the display shows three blinking dashes.

14 How to open the door during

the cycle of a programme

You can open the door, after having set the washing

machine to PAUSE, provided the following

conditions exist:

• the washing machine is not in the heating phase

beyond 40°C;

• the level of the water is not high;

• the drum is not turning.

If these requirements are met, when you pause the

washing machine, the DOOR LOCKED light goes

out and the door can be opened.

Should it not be possible to open the door, and

should it be absolutely necessary to do so, switch

the machine off by pressing the ON/OFF button

“AÇMA/KAPAMA”.

After approximately 2 minutes, you can open the

door.

Pay attention to the level and temperature of the

water in the washing machine!

When you close the door and press the ON/OFF

button again, the washing machine will resume the

programme from the point where it had been

interrupted.

15 End of programme

At the end of the programme, the washing machine

stops automatically, gives an audible signal, and

displays a blinking zero.

If you had selected the RINSE HOLD option,

the START/PAUSE button light flashes to indicate

that the water must be drained. The display shows a

steadily lit zero.

When the programme has been completed, a

blinking zero appears on the display and the audible

signal is given.

The DOOR LOCKED light goes out at once.

Press the SKIP/RESET button repeatedly to erase

the programme that has just been carried out. If

you omit to do this, the next time you switch the

washing machine on, the blinking zero will

appear on the display and you will hear the

audible signal.

Note: when you switch the machine on, if you must

erase the previously performed programme, it is also

sufficient to press the FABRIC button “ÇAMAÇIR”

and select a new programme.

Press the ON/OFF button to switch the machine

off. The relevant light will go out.

Remove the laundry from the washing machine.

Check whether the drum is completely empty, by

rotating it with your hand. The purpose of this is to

prevent any items of laundry from remaining

accidentally in the drum, where they might get

damaged in a subsequent wash (e.g. by shrinking) or

bleed colour into another load of laundry.

We advise you to close the water supply tap and

disconnect the plug from the socket.

Leave the door ajar in order to air the washing

machine.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 18

ENGLISH

Programme chart

Washing programmes

Wash programme Temp.

Additional

functions

Max.

load

Consumption**

Energy

kWh

Water

lt.

Time

min.

1.9 52 149

Fabrics

Cottons (Whites)

Beyazlar

60°-95°

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

5 kg

Cotton fabrics

e.g. sheets,

tablecloths,

household, linen

0.93 49 130

Cottons *

(Coloureds)

Beyazlar

60°-40°-30°

COLD

SOGUK

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

5 kg

Coloured cotton or

linen items, e.g.

shirts, blouses,

underwear, towels,

household, linen

0.90 56 87

Synthetic fabrics

Sintetikler

60°-40°-30°

COLD

SOGUK

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

2.5 kg

Synthetic or

mixed fabrics

e.g. shirts,

blouses,

underwear

0.60 53 104

Delicate fabrics

Narın çamaçirlar

40°-30°

COLD

SOGUK

SPIN SPEED

RINSE HOLD

PREWASH

SUPER RINSE

QUICK

2.5 kg

Acrylic fabrics,

viscose,

polyester,

synthetic blends

0.30 48 57

Wool

Yünlüler

40°-30°

COLD

SOGUK

SPIN SPEED

RINSE HOLD

2 kg

Wool marked

pure new wool,

washable,

preshrunk

0.25 46 55

Hand wash

Elde Yikananlar

40°-30°

COLD

SOGUK

SPIN SPEED

RINSE HOLD

2 kg

Wool mixtures,

silk

* This programme at 60°C with a load of 5 kg is the reference programme for the data entered in the energy

label, in compliance with EEC 92/75 standards.

** This data is given purely as an indication: the consumption values may vary in relation to the quantity and

type of laundry, the temper-ature of the water supply and the ambient temperature. The data refers to the

highest temperature provided for each programme and to a load of 5 kg of cotton items.

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 19

International wash code symbols

These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.

Energetic wash

Delicate wash

Max. wash

temperature

95°C

Max. wash

temperature

60°C

Max. wash

temperature

40°C

Max. wash

temperature

30°C

Hand wash Do not

wash

at all

Bleaching Bleach in cold water Do not bleach

Ironing Hot iron

max 200°C

Warm iron

max 150°C

Lukewarm iron

max 110°C

Do not iron

Dry cleaning Dry cleaning

in all solvents

Dry cleaning in

perchlorethylene,

petrol, pure alcohol,

R 111 & R 113

Dry cleaning

in petrol,

pure alcohol

and R 113

Do not

dry clean

Drying Flat On the line On clothes

hanger

Tumble dry

high

temperature

low

temperature

Do not

tumb

le dr

132993580•EW1220/1620N•gb 07/07/03 11:22 Pagina 20

Sayfa yükleniyor ...

Electrolux EW1220N Kullanım kılavuzu

Marka: Electrolux

Model: EW1220N

Kategori: Çamaşır makineleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

EW1620N

PDF İndir

rapor

Diğer dillerde

English: Electrolux EW1220N User manual

Electrolux EW1220N Kullanım kılavuzu

Bu kılavuz için de uygundur

Electrolux EW1220N Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler