Simplicity 073034-0 Kullanım kılavuzu

Marka: Simplicity

Model: 073034-0

Kategori: Motorlu taşıt aksesuarları

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

MODEL 073034-0

BRIGGS & STRATTON UK Ltd.,

WINSFORD, CHESHIRE, UK

Commercial Water Pump WP20

Operator’s Manual

Bomba de agua comercial WP20

Manual del operario

Bomba de Água para

Aplicações Comerciais WP20

Manual do Operador





Original Instruction

Appearance will vary slightly

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Not for

Reproduction

ED GF

N M

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

5 6

Not for

Reproduction

Thank you for purchasing this quality-built Briggs & Stratton water pump. We are pleased that you’ve placed your confidence in

the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs & Stratton

water pump will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with water pumps and how

to avoid them. This water pump is designed and intended only for transferring water that may contain sand or silt. It is not

intended for any other purpose. It is important that you read and understand these instructions thoroughly before attempting to

start or operate this equipment. 

This water pump requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.



Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues. These

numbers can be found in locations shown in Figure 1.

Date of Purchase

Water Pump

Model Number

Model Revision

Serial Number

Engine

Model Number

Serial Number

express written permission of Briggs & Stratton Power Products Group, LLC.



Illustrations....................................................... 3

 ....................................... 6

 ........................................................ 8

Operation ........................................................ 9

Maintenance ..................................................... 10

 ................................................. 14

Warranties ...................................................... 15

 ............................................ 18

Español

Português

Türkçe

Not for

Reproduction

6 BRIGGSandSTRATTON.COM



SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during water

pump operation.



The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal njury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure

or operating technique that the manufacturer does not

specifically recommend, you must satisfy yourself that it is

safe for you and others. You must also make sure that the

operating technique that you choose does not render the

water pump unsafe.



 

 

 

D - Toxic Fumes J - Read Manual



WARNING Running engine gives off carbon monoxide,

an odourless, colourless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Operate water pump ONLY outdoors.•

DO NOT start or run engine indoors or in an enclosed •

area, even if windows and doors are open.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING Use of water pump can create puddles and

slippery surfaces.

Operate water pump from a stable surface.•

The area should have adequate slopes and drainage to •

reduce the possibility of a fall due to slippery surfaces.

WARNING Fuel and its vapours are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING OR DRAINING FUEL

Turn water pump OFF and let it cool at least 2 minutes •

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

Fill or drain fuel tank outdoors.•

DO NOT overfill tank. Allow space for fuel expansion.•

If fuel spills, wait until it evaporates before starting engine.•

Keep fuel away from sparks, open flames, pilot lights, •

heat, and other ignition sources.

DO NOT light a cigarette or smoke.•

WHEN STARTING EQUIPMENT

DO NOT start unless spark plug, muffler, fuel cap, and air •

cleaner are in place.

DO NOT crank engine with spark plug removed.•

WHEN OPERATING EQUIPMENT

DO NOT pump flammable liquids, such as fuel or fuel oils. •

This water pump is not for use in mobile equipment or •

marine applications.

DO NOT tip engine or equipment at angle which causes •

fuel to spill.

Secure water pump. Loads from hoses may cause tipover.•

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

Transport/repair with fuel tank EMPTY or with fuel shutoff •

valve OFF.

Disconnect spark plug wire.•

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

Store away from furnaces, stoves, water heaters, clothes •

dryers, or other appliances that have pilot light or other

ignition source because they can ignite fuel vapours.

CA B

Not for

Reproduction

NOTICE This water pump is manufactured to pump ONLY

water that is not intended for human consumption.

NOTICE Any attempt to crank or start the engine before it

has been properly serviced with the recommended oil will

result in equipment failure.

Refer to • Maintenance for oil fill information.

Damage to equipment resulting from failure to follow this •

instruction will void engine and water pump warranty.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

When starting engine, pull cord slowly until resistance is •

felt and then pull rapidly to avoid kickback.

Keep hands and body clear from discharge of pump.•

Secure discharge hose to avoid whipping.•

WARNING Backfire, fire or engine damage

could occur.

DO NOT stop engine by moving choke control to “Choke” •

position ( ).

WARNING Unintentional sparking can result in fire or

electric shock.

When adjusting or making repairs to your water pump•

Disconnect the spark plug wire from the spark plug and •

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.•

Do not check for spark with spark plug removed.•

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

Do not touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

Keep at least 1.5 m (5 ft) of clearance on all sides of water •

pump including overhead.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

NEVER place hands or body parts inside of running pump •

or hoses.

NEVER operate water pump without protective housing •

or covers.

DO NOT wear loose clothing, jewelry or anything that may •

be caught in the starter or other rotating parts.

Tie up long hair and remove jewelry.•

NOTICE Improper treatment of water pump can damage it

and shorten its life.

If you have questions about intended use, ask dealer or •

contact qualified service center.

Be sure pump chamber is filled with water before starting •

the engine. Never run pump without priming.

Use a non-collapsible hose on the suction side of pump.•

Use water pump only for intended uses.•

Pumping sea water, beverages, acids, chemical solutions, •

or any other liquid that promotes corrosion can damage

the pump.

Ensure all connections are air tight.•

DO NOT obstruct suction or discharge hose in any way.•

NEVER operate pump without strainer basket connected •

to end of suction hose.

DO NOT exceed suction head maximum and total head •

(see Specifications). Use shortest suction head possible.

NEVER allow vehicles to drive over hoses. If a hose •

must be positioned across a roadway, use planking on

each side of hose to allow vehicles to pass over without

obstructing or collapsing hose.

Anchor pump to avoid “walking” or equipment movement, •

especially if located near a ditch or edge of open ravine.

The equipment could fall in.

Keep equipment away from edge of river or lake where it •

could cause the bank to collapse.

DO NOT insert any objects through cooling slots.•

NEVER operate units with broken or missing parts, or •

without protective housing or covers.

DO NOT by-pass any safety device on this machine.•

NEVER move machine by pulling on hoses - use frame •

on unit.

Check fuel system for leaks or signs of deterioration, such •

as chafed or spongy hose, loose or missing clamps, or

damaged tank or cap. Correct all defects before operating

water pump.

This equipment is designed to be used with Briggs •

& Stratton Power Products authorized parts only. If

equipment is used with parts that DO NOT comply

with minimum specifications, user assumes all risks

and liabilities.

CAUTION Excessively high operating speeds increase

risk of injury and damage to water pump.

Excessively low speeds impose a heavy load.

DO NOT tamper with governed speed.•

DO NOT modify water pump in any way.•

DO NOT allow unqualified persons or children to operate •

or service water pump.

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

How to Use Manual Figures

Refer to figure numbers

A to N Refer to part/action in figures

Components (see Figure 1)

A -  — Always disconnect spark plug wire when

servicing water pump.

B - Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

C - Engine Controls — Used for starting, stopping, and

setting engine speed.

D - Recoil Starter — Used for starting the engine manually.

E - Oil Drain — Drain engine oil here.

F - Oil Fill — Check and add engine oil here.

G - ID Label — Provides model and serial number of

water pump.

H -  — Fill tank with regular unleaded fuel here.

Always leave room for fuel expansion.

J - Priming Plug — Fill pump with water here to prime

pump before starting.

K -  — Connect discharge hose here.

L -  — Stamped on valve cover.

Provides model, type and code number of engine.

M - Water Drain Plug — Remove to drain water from pump

and to flush internal components with clean water.

N - Suction Inlet — Connect reinforced suction hose here.



Read entire operator’s manual before you attempt to

assemble or operate your new water pump.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter or otherwise improve the product and

this document at any time without prior notice.

The Emissions Control System for this water pump is

warranted for standards set by the Environmental Protection

Agency and the California Air Resources Board.

Your water pump requires some assembly and is ready

for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your water

pump, please contact the store at which you purchased the

unit or any authorized dealer. If calling for assistance, please

have the model, revision, and serial number from the ID label

available. See Figure 1 for ID label location.



1. Remove the parts bag, accessories, and inserts

included with water pump.

2. Open carton completely by cutting each corner from top

to bottom.

3. Ensure you have all included items prior to assembly.



 • Waterpump

 • Partsbag(whichincludesthefollowing):

 • Operator’smanual

 • Strainerbasketandbarb

 • Hosebarb(2)

 • Barbcuff(2)

 • Rubberseal(2)

 • Hoseclamp(3)

 • Anti-vibrationkit(whichincludesthefollowing)

  • Anti-vibrationpad(4)

  • Bolt(4)

  • Washer(4)

  • Locknut(4)

  • Instructionsheet

To prepare your water pump for operation, you will need to

performthesetasks:

1. Attach anti-vibration pads.

2. Add oil to engine crankcase.

3. Add fuel to fuel tank.

 4. Movewaterpumptosafeoperatinglocation.

5. Assemble and connect hoses.

6. Locate strainer basket into water source.

7. Prime the water pump.



Using 10mm wrenches, attach anti-vibration pads to water

pump as shown on instruction sheet included with anti-

vibration kit. You must attach anti-vibration pads prior to

adding engine oil and fuel.

Add Engine Oil

1. Place water pump on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill cap.

3. Using oil funnel (optional), slowly pour recommended

oil into oil fill opening until the point of overflowing (F,

Figure 1). See Oil Recommendations in Maintenance

section. Verify oil is the correct viscosity for current

ambient temperature.

 4. Replaceoilfillcapandfullytighten.

Not for

Reproduction

Add Fuel

1. Make sure water pump is on a level surface.

2. Clean area around fuel fill cap (H, Figure 1) and

remove cap.



 • Clean,fresh,unleadedgasoline.

 • Aminimumof87octane/87AKI(91RON).Highaltitude

use, see High Altitude.

 • Gasolinewithupto10%ethanol(gasohol)orupto15%

MTBE (methyl tertiary butyl ether) is acceptable.

3. Slowly add regular unleaded fuel to fuel tank. Be careful

nottooverfill.Allowabout4cm(1.5in)oftankspace

for fuel expansion.

 4. Installfuelcapandletanyspilledfuelevaporatebefore

starting engine.

To protect the fuel system from gum formation, mix in a

fuel stabilizer when adding fuel. See Storage. All fuel is

not the same. If you experience starting or performance

problems after using fuel, switch to a different fuel provider

or change brands. This engine is certified to operate on

gasoline. The emission control system for this engine is EM

(Engine Modifications).

Operation

If you have any problems operating your water pump, please

contact the store at which you purchased the unit or any

authorized dealer.





Place water pump outdoors in an area that will not

accumulate deadly exhaust gas. DO NOT place water

pump where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

water pump.



Head refers to the height of a column of water that can be

delivered by the discharge of the pump.

Suction Head (C, Figure 2) is the vertical distance between

the center of the pump and the surface of the liquid on the

suction side of the pump. May also be referred to as “suction

lift”.Theatmosphericpressureof1bar(14.5psi)atsealevel

limitssuctionheadlifttolessthanapproximately8m(26ft)

for any pump.

 (A, Figure 2) is the vertical distance

between the pump’s discharge port and the point of

discharge, which is the liquid surface if the hose is

submerged or pumping into the bottom of a tank.

Total Head (B, Figure 2) is the sum of the suction head

value plus the discharge head value.

As water pumping height increases, pump output decreases.

The length, type, and size of the suction and discharge

hoses can also significantly affect pump output.

It is important for the suction operation to be the shorter part

of the total pumping action. This will decrease the priming

time and improve pump performance by increasing the

discharge head.

See Specifications for maximum head values.



Operating Location

For best pump performance, locate the pump on a flat, level

surface as close as possible to the water to be pumped.

Secure water pump to avoid tipover. Use hoses that are no

longer than necessary.



Assemble strainer (G, Figure 2) and fitting (F, Figure 2) to

suction hose using hose clamps. Attach suction hose to

pump inlet (N, Figure 1).

Place strainer basket into water to be pumped. Basket must be

fully immersed in water. To reduce sand or silt suction, place

basket into bucket (E, Figure 2) or on top of coarse rocks.

Optionally, assemble fitting (F, Figure 2) to discharge

hose and secure with hose clamp. Attach to pump outlet

(K, Figure 1). Direct water discharge away from home,

electrical devices or anything not desired to get wet.

WARNING Fuel and its vapours are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING FUEL

Turn water pump OFF and let it cool at least 2 minutes •

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

Fill or drain fuel tank outdoors.•

DO NOT overfill tank. Allow space for fuel expansion.•

If fuel spills, wait until it evaporates before starting engine.•

Keep fuel away from sparks, open flames, pilot lights, •

heat, and other ignition sources.

DO NOT light a cigarette or smoke.•

WARNING Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

Keep at least 1.5 m (5 ft) of clearance on all sides of water •

pump including overhead.

Not for

Reproduction

10 BRIGGSandSTRATTON.COM



1. Remove priming plug from top of pump (D, Figure 2).

2. Fill pump with clean, clear water up to level shown.

3. Replace priming plug.



Usethefollowingstartinstructions:

1. Make sure unit is on a flat, level surface and pump

chamber is primed.

2. Turn fuel shutoff (D, Figure 3) to “On” position.

3. Move engine speed lever (B) to “Fast” ( ) position.

 4. Movechokelever(C) to “Choke” ( ) position.

5. Push on/off switch (A) to “On” position.

6. Grasp recoil handle (E) and pull slowly until slight

resistance is felt. Then pull handle rapidly to overcome

compression, prevent kickback and start engine.

If excessive fuel is present in the air/fuel mixture

causing a “flooded” condition, engine won’t start. Move

choke lever to “Run” ( ) position and pull handle

repeatedly until engine starts.

7. As the engine warms, move choke lever (C) to “Run”

(

) position. Operate with choke in “Run” position.

It may take a few minutes for water pump to begin

pumping water.

Pump output is controlled by adjusting engine speed. Moving

the engine speed lever in the “Fast” ( ) direction will

increase pump output, and moving the engine speed lever in

the “Slow” ( ) direction will decrease pump output.



1. Move engine speed lever (B, Figure 3) to

“Slow” ( ) position.

2. Push on/off switch (A) to “Off” position.

3. Turn fuel shutoff (D) to “Off” position.



1. Disconnect and drain suction and discharge hoses.

2. Remove drain plug (M, Figure 1) at bottom of pump.

3. Remove primer plug (J) from top of pump and flush

internal components of pump with clean water.

 4. Replacebothplugsandfingertighten.

Maintenance



Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

WARNING Running engine gives off carbon monoxide,

an odourless, colourless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Operate water pump ONLY outdoors.•

DO NOT start or run engine indoors or in an enclosed •

area, even if windows and doors are open.

Keep exhaust gas from entering a confined area through •

windows, doors, ventilation intakes, or other openings.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

When starting engine, pull cord slowly until resistance is •

felt and then pull rapidly to avoid kickback.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

Do not touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

Keep at least 5 feet (1.5 m) of clearance on all sides of •

water pump including overhead.

WARNING Backfire, fire or engine damage

could occur.

DO NOT stop engine by moving choke control to “Choke” •

position ( ).

WARNING Fuel and its vapours are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN OPERATING EQUIPMENT

DO NOT pump flammable liquids, such as fuel or fuel oils. •

This water pump is not for use in mobile equipment or •

marine applications.

DO NOT tip engine or equipment at angle which causes •

fuel to spill.

Secure water pump. Loads from hoses may cause tipover.•

NOTICE Improper treatment of water pump can damage it

and shorten its life.

Be sure pump chamber is filled with water before starting •

the engine. Never run pump without priming.

NOTICE Improper treatment of water pump can damage it

and shorten its life.

NEVER operate pump without strainer basket connected •

to end of suction hose.

Keep strainer out of sand or silt - place in bucket or •

on stones.

DO NOT let pump run dry or damage to seals may result. •

Never run pump without priming.

Not for

Reproduction



* Service sooner when operating under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the water pump. See any authorized Briggs

& Stratton dealer for service.

The water pump’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

water pump as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your water pump.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any non-

road engine repair establishment or individual. However,

to obtain ”no charge” emissions control service, the work

must be performed by a factory authorized dealer. See the

Emissions Warranty.

Water Pump Maintenance

Maintenance consists of keeping the water pump clean.

Store the unit in a clean dry environment where it will not be

exposed to excessive dust, dirt, moisture or any corrosive

vapours. Engine cooling air slots must not become clogged

with dirt, leaves or any other foreign material.

Do Not use a garden hose to clean engine. Water can enter

engine fuel system and cause problems.

Cleaning

Daily or before use, look around and underneath water pump

for signs of oil or fuel leaks. Clean accumulated debris from

inside and outside water pump. Keep linkage, spring and

other engine controls clean. Keep area around and behind

muffler free from any combustible debris. Use low pressure

air (not to exceed 1.7 bar (25 psi)) to blow away dirt.

Inspect cooling air slots and opening on water pump. These

openings must be kept clean and unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris.

 • Useadampclothtowipeexteriorsurfacesclean.

 • Useasoftbristlebrushtoloosencakedondirtoroil.

 • Useavacuumcleanertopickuploosedirtanddebris.

Removesiltandsludgebuildupinpumpbody:

 • Openprimingplugandremovedrainplug.

 • Flushinternalcomponentsofpumpwithcleanwater.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SG, SH,

SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

*Below4°C(40°F)theuseofSAE30willresultinhardstarting.

**Above27°C(80°F)theuseof10W30maycauseincreasedoil

consumption. Check oil level more frequently.

First 5 hours

Change oil

Every8hoursordaily

Check oil level

Clean area around muffler

Clean finger guard

Every 50 hours or annually *

Change oil

Clean and inspect spark arrester (if equipped)

Clean air filter pre-cleaner

Annually

Replace air filter

Replace pre-cleaner

Replace spark plug

Clean air cooling system

Clean any sludge buildup inside pump

WARNING Unintentional sparking can result in fire or

electric shock.

When adjusting or making repairs to your water pump•

Disconnect the spark plug wire from the spark plug and •

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.•

Do not check for spark with spark plug removed.•

Not for

Reproduction

12 BRIGGSandSTRATTON.COM



Oil level should be checked prior to each use or at least

every8hoursofoperation.Keepoillevelmaintained.

1. Make sure water pump is on a level surface.

2. Clean area around oil fill (A,Figure4)andremoveoil

fill cap.

3. Verify oil is at the point of overflowing at oil fill

opening (B).

 4. Replaceandtightenoilfillcap.

Adding Engine Oil

1. Make sure water pump is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the point

of overflowing at oil fill (B,Figure4).

 4. Replaceandtightenoilfillcap.



Change the oil after the first 5 hours of operation. Change oil

every 50 hours thereafter. If you are using your water pump

under extremely dirty or dusty conditions, or in extremely hot

weather, change the oil more often.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change the oil while the engine is still warm from running,

asfollows:

1. Make sure water pump is on a level surface.

2. Disconnect the spark plug wire (A, Figure 1) from the

spark plug and place the wire where it cannot contact

spark plug.

3. Clean area around oil drain plug (F). The oil drain plug

is located at base of engine, opposite carburetor.

 4. Removeoildrainpluganddrainoilcompletelyintoa

suitable container.

5. Reinstall oil drain plug and tighten securely. Remove oil

fill cap.

6. Slowly pour oil (about 0.6 l (20 oz)) into oil fill

opening (F) to the point of overflowing at oil fill cap.

DO NOT overfill.

7. Replace and tighten oil fill cap.

 8. Wipeupanyspilledoil.



Clean or replace the air cleaner elements as recommended

in the Maintenance Chart or more often if operating under

dirty or dusty conditions. Your engine will not run properly

and may be damaged if you run it with a dirty air cleaner.

Toservicetheaircleaner,followthesesteps:

1. Remove fastener (A, Figure 5) and cover (B).

2. Remove fastener (C) and filter assembly (D).

3. If equipped, remove pre-cleaner (G) from the filter. To

loosen debris, gently tap filter on a hard surface. If filter

is excessively dirty, replace with new filter.

The air cleaner system uses a pleated filter with an

optional pre-cleaner. The pre-cleaner can be washed

and reused.

 4. Washpre-cleanerinliquiddetergentandwater.Then

allow it to thoroughly air dry. Do not oil the pre-cleaner.

5. Assemble dry pre-cleaner to filter.

6. Install filter and pre-cleaner into base (F) and onto stud

(E). Make sure filter fits securely into base. Secure filter

with fastener (C).

7. Install cover (B) and secure with fastener (A). Make

sure fastener is finger tight.



Change the spark plug as recommended in the Maintenance

Chart. This will help your engine to start easier and

run better.

1. Clean area around spark plug (A, Figure 1).

2. Remove and inspect spark plug.

3. Check electrode gap with wire feeler gauge (Figure 6)

and set spark plug gap to 0.76 mm (0.030 in)

if necessary.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

Used motor oil has been shown to cause skin cancer in •

certain laboratory animals.

Thoroughly wash exposed areas with soap and water.•

WARNING Fuel and its vapours are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

DO NOT start or run the engine unless spark plug, muffler, •

fuel cap, and air cleaner are in place.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

Do not touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

Keep at least 5 feet (1.5 m) of clearance on all sides of •

water pump including overhead.

NOTICE DO NOT use pressurized air or solvents to clean

the foam air cleaner.

Pressurized air can damage the foam air cleaner and •

solvents will dissolve the foam air cleaner.

WARNING Unintentional sparking can result in fire or

electric shock.

Disconnect the spark plug wire from the spark plug and •

place the wire where it cannot contact spark plug.

Never pull recoil starter handle with spark plug removed.•

Not for

Reproduction

 4. Replacesparkplugifelectrodesarepitted,burned

or porcelain is cracked. Use the recommended

replacement plug. See Specifications.

5. Install spark plug and tighten firmly.



The engine exhaust muffler may be equipped a spark

arrester screen. If equipped, inspect and clean as

recommended in the Maintenance Chart.

If you use your water pump on any forest-covered, brush-

covered, or grass-covered unimproved land, it must have

a spark arrester. The spark arrester must be maintained in

good condition by the owner/operator.

If the engine has been running, the muffler will be very hot.

Allow the muffler to cool before servicing the spark arrester.

1. Remove spark arrester screen for cleaning

and inspection.

2. Inspect screen and replace if torn, perforated or

otherwise damaged. Do Not use a defective screen.

If screen is not damaged, clean it with commercial

solvent.

3. Reattach spark arrester screen to muffler.

You can purchase a new spark arrester screen by contacting

your local Briggs & Stratton service center.



This is an air cooled engine. Dirt or debris can restrict air

flow and cause the engine to overheat, resulting in poor

performance and reduced engine life. Debris cannot be

removed without partial engine disassembly. For this reason,

we recommend you have an authorized Briggs & Stratton

service dealer clean the cooling system as recommended

in the Maintenance Chart. Equally important is to keep the

area around and behind the muffler free of any combustible

debris. See Cleaning.

Storage

If the water pump cannot be used at least once every

30 days or you must store the unit for more than 30 days, use

the following information as a guide to prepare it for storage.





Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton FRESH START® fuel stabilizer, available as a

liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine for

2 minutes to circulate the stabilizer throughout the fuel system.

Theengineandfuelcanthenbestoredupto24months.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container.

Then run the engine until it stops from lack of fuel. The use of

a fuel stabilizer in the storage container is recommended to

maintain freshness.



While engine is still warm, change the engine oil.



1. Remove spark plug and pour about 15 ml (1/2 oz) of

clean engine oil into the cylinder.

2. Install spark plug and pull starter handle slowly to

distribute oil.

Clean Water Pump

1. Drain water pump as described in Drain and Flush

Water Pump.

2. Clean water pump as described in Cleaning.

3. Check that openings on water pump are open

and unobstructed.



1. DO NOT store fuel from one season to another unless it

has been treated as described in Protect Fuel System.

2. Replace fuel can if it starts to rust. Contaminated fuel

will cause engine problems.

3. Cover unit with a suitable protective cover that does not

retain moisture.

 4. Storewaterpumpinclean,dryarea.

WARNING Storage covers can be flammable.

DO NOT place a storage cover over a hot water pump.•

Let equipment cool for a sufficient time before placing the •

cover on the equipment.

WARNING Fuel and its vapours are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL

IN TANK

Store away from furnaces, stoves, water heaters, clothes •

dryers, or other appliances that have pilot light or other

ignition source because they can ignite fuel vapours.

WHEN DRAINING FUEL

Turn water pump OFF and let it cool at least 2 minutes •

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

Drain fuel tank outdoors.•

Keep fuel away from sparks, open flames, pilot lights, •

heat, and other ignition sources.

DO NOT light a cigarette or smoke.•

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

Do not touch hot parts and AVOID hot exhaust gases.•

Allow equipment to cool before touching.•

Keep at least 5 feet (1.5 m) of clearance on all sides of •

water pump including overhead.

Not for

Reproduction

14 BRIGGSandSTRATTON.COM



Problem Cause Correction

No pump output or low

pump output when water

pump is running.

1. Pump not primed. 1.

Fill pump chamber with water and prime pump.

2. Suction hose restricted, collapsed,

damaged, too long, or diameter too small.

2. Replace suction hose.

3. Strainer not completely under water. 3. Sink the strainer and the end of suction hose

completely under water.

4.Airleakatsuctionhoseconnector. 4.R

eplace sealing washer if missing or

damaged. Tighten hose connector and clamp.

5. Strainer clogged. 5. Clean debris from strainer.

6. Discharge hose restricted, damaged, too

long, or diameter too small.

6. Replace discharge hose.

7. Excessive or marginal head. 7.

Relocate pump and/or hoses to reduce head.

8.Enginespeedleverisin“Slow”position. 8.Moveenginespeedleverto“Fast”position.

Engine will not start;

lacks power; starts and

runs rough; or “hunts”

or falters.

1. Rocker switch set to “Off”. 1. Set switch to “On”.

2. Fuel shutoff is in “Off” position. 2. Turn fuel shutoff to “On” position.

3. Dirty air cleaner. 3. Clean or replace air cleaner.

4.Outoffuel. 4.Waittwominutesandfillfueltank.

5. Stale or contaminated fuel or water in fuel. 5.

Drain fuel tank and carburetor; fill with fresh fuel.

Spark plug wire not connected to spark plug.

6. Connect wire to spark plug.

7. Bad spark plug. 7. Replace spark plug.

8.Excessivefuelispresentintheair/fuel

mixture causing a “flooded” condition.

8.Wait5minutesandre-crankengine.

9.Carburetorisoutofadjustment. 9.ContactAuthorizedservicefacility.

Engine shuts down

when running.

Out of fuel. Wait two minutes and fill fuel tank.

Not for

Reproduction

Warranties







The California Air Resources Board, U.S. EPA, and Briggs & Stratton (B&S)

are pleased to explain the emissions control system warranty on your Model

Year2008andlaterengine/equipment.InCalifornia,newsmalloff-road

engines must be designed, built, and equipped to meet the State’s stringent

anti-smog standards. B&S must warrant the emissions control system on

your engine/equipment for the periods of time listed below provided there

has been no abuse, neglect, or improper maintenance of your small off-

road engine.

Your emissions control system may include parts such as the carburetor or

fuel injection system, fuel tank, ignition system, and catalytic converter. Also

included may be hoses, belts, connectors, sensors, and other emissions-

related assemblies. Where a warrantable condition exists, B&S will repair

your engine/equipment at no cost to you including diagnosis, parts,

and labor.

Manufacturer’sWarrantyCoverage:

Small off-road engines are warranted for two years. If any emissions-related

part on your engine/equipment is defective, the part will be repaired or

replaced by B&S.

Owner’sWarrantyResponsibilities:

• Asthesmallengine/equipmentowner,youareresponsibleforthe

performance of the required maintenance listed in your owner’s

manual. B&S recommends that you retain all receipts covering

maintenance on your engine/equipment, but B&S cannot deny

warranty solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

• Astheengine/equipmentowner,youshouldhoweverbeawarethat

B&S may deny you warranty coverage if your engine/equipment or

a part has failed due to abuse, neglect, improper maintenance, or

unapproved modifications.

• Youareresponsibleforpresentingyourengine/equipmenttoaB&S

distribution center, servicing dealer, or other equivalent entity, as

applicable, as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30

days. If you have any questions regarding your warranty rights and

responsibilities,youshouldcontactB&Sat414259-5262.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control

Warranty Coverage. It is in addition to the B&S engine warranty for non-

regulated engines found in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below

(the emissions control systems parts) to the extent these parts were

present on the engine purchased.

a. Fuel Metering System

  • Coldstartenrichmentsystem(softchoke)

  • Carburetorandinternalparts

  • Fuelpump

  • Fuelline,fuellinefittings,clamps

  • Fueltank,capandtether

  • Carboncanister

b. Air Induction System

  • Aircleaner

  • Intakemanifold

  • Purgeandventline

c. Ignition System

  • Sparkplug(s)

  • Magnetoignitionsystem

d. Catalyst System

  • Catalyticconverter

  • Exhaustmanifold

  • Airinjectionsystemorpulsevalve

e. Miscellaneous Items Used in Above Systems

  • Vacuum,temperature,position,timesensitivevalves

and switches

  • Connectorsandassemblies

2. 

For a period of two years from date of original purchase, B&S warrants

to the original purchaser and each subsequent purchaser that the

engine is designed, built, and equipped so as to conform with all

applicable regulations adopted by the Air Resources Board; that it

is free from defects in material and workmanship that could cause

the failure of a warranted part; and that it is identical in all material

respects to the engine described in the manufacturer’s application

for certification. The warranty period begins on the date the engine is

originally purchased.

 Thewarrantyonemissions-relatedpartsisasfollows:

• Anywarrantedpartthatisnotscheduledforreplacementasrequired

maintenance in the owner’s manual supplied, is warranted for the

warranty period stated above. If any such part fails during the period

of warranty coverage, the part will be repaired or replaced by B&S at

no charge to the owner. Any such part repaired or replaced under the

warranty will be warranted for the remaining warranty period.

• Anywarrantedpartthatisscheduledonlyforregularinspectioninthe

owner’s manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be

warranted for the remaining warranty period.

• Anywarrantedpartthatisscheduledforreplacementasrequired

maintenance in the owner’s manual supplied, is warranted for the

period of time prior to the first scheduled replacement point for that

part. If the part fails prior to the first scheduled replacement, the part

will be repaired or replaced by B&S at no charge to the owner. Any

such part repaired or replaced under warranty will be warranted for the

remainder of the period prior to the first scheduled replacement point

for the part.

• AddonormodifiedpartsthatarenotexemptedbytheAirResources

Board may not be used. The use of any non exempted add on

or modified parts by the owner will be grounds for disallowing a

warranty claim. The manufacturer will not be liable to warrant failures

of warranted parts caused by the use of a non exempted add on or

modified part.

3. 

Coverage shall extend to the failure of any engine components caused

by the failure of any warranted emissions parts.

4. ClaimsandCoverageExclusions

Warranty claims shall be filed according to the provisions of the B&S

engine warranty policy. Warranty coverage does not apply to failures

of emissions parts that are not original equipment B&S parts or to

parts that fail due to abuse, neglect, or improper maintenance as set

forth in the B&S engine warranty policy. B&S is not liable for warranty

coverage of failures of emissions parts caused by the use of add-on or

modified parts.

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Look For Relevant Emissions Durability Period and Air Index Information

On Your Engine Emissions Label

Engines that are certified to meet the California Air Resources Board

(CARB) Emissions Standard must display information regarding the

Emissions Durability Period and the Air Index. Briggs & Stratton makes this

information available to the consumer on our emissions labels. The engine

emissions label will indicate certification information.

The Emissions Durability Period describes the number of hours of actual

running time for which the engine is certified to be emissions compliant,

assuming proper maintenance in accordance with the Operating &

MaintenanceInstructions.Thefollowingcategoriesareused:

Moderate:

Engine is certified to be emissions compliant for 125 hours of actual

engine running time.



Engine is certified to be emissions compliant for 250 hours of actual

engine running time.

Extended:

Engine is certified to be emissions compliant for 500 hours of actual

engine running time.

For example, a typical walk-behind lawn mower is used 20 to 25 hours

per year. Therefore, the Emissions Durability Period of an engine with

an intermediate rating would equate to 10 to 12 years. Briggs & Stratton

engines are certified to meet the United States Environmental Protection

Agency (USEPA) Phase 2 emissions standards. For Phase 2 certified

engines, the Emissions Compliance Period referred to on the Emissions

Compliance label indicates the number of operating hours for which the

engine has been shown to meet Federal emissions requirements.

For engines less than 225 cc displacement.

Category C = 125 hours

Category B = 250 hours

Category A = 500 hours

For engines of 225 cc or more displacement.

Category C = 250 hours

Category B = 500 hours

Category A = 1000 hours

Not for

Reproduction

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the warranty

is void if the manufacturing date or the serial number on the water pump or engine has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

useandservice.Thiswarrantywillnotcoverthefollowingrepairsandequipment:

• Normal Wear:OutdoorPowerEquipment,likeallmechanicaldevices,needsperiodicpartsandservicetoperformwell.Thiswarrantydoesnotcover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance:Thiswarrantydoesnotapplytoequipmentorpartsthathavebeensubjectedtoimproperorunauthorizedinstallationor

alteration and modification, misuse, negligence, accident, overloading, overspeeding, improper maintenance, repair or storage so as, in our judgment,

to adversely affect its performance and reliability. This warranty also does not cover normal maintenance such as air filters, adjustments, fuel system

cleaning and obstruction (due to chemical, dirt, etc.).

• :Thiswarrantyexcludeswearitemssuchasseals,o-rings,etc.Thiswarrantyalsoexcludespumpsthathavebeenrunwithout

water or subjected to freezing or chemical deterioration. This water pump is warranted for use in clear water applications, as certain components will

experience accelerated wear depending on the percentage and abrasive degree of sediment passing through the pump. Accessory parts, such as hoses

or strainers, are excluded from the product warranty. This warranty excludes failures due to acts of God and other force majeure events beyond the

manufacturers control. 198201E,Rev.B,12/31/2006

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MINWAUKEE, WI, USA

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC WATER PUMP OWNER WARRANTY POLICY

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the water pump that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED

WARRANTIES ARE EXCLUDED. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO THE EXTENT EXCLUSION

IS PERMITTED BY LAW. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives

you specific legal rights and you may also have other rights which vary from state to state or country to country.

Effective February 1, 2006 replaces all undated Warranties and all Warranties dated before February 1, 2006

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated above.

“Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for commercial,

income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for purposes of

this warranty.

NO WARRANTY REGISTRATION IS NECESSARY TO OBTAIN WARRANTY ON BRIGGS & STRATTON PRODUCTS. SAVE YOUR PROOF OF

PURCHASE RECEIPT. IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED,

THE MANUFACTURING DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

2 years

Consumer Use

Commercial Use

WARRANTY PERIOD

Not for

Reproduction

18 BRIGGSandSTRATTON.COM

PowerRatings:ThegrosspowerratingforindividualgasenginemodelsislabeledinaccordancewithSAE(SocietyofAutomotiveEngineers)

codeJ1940(SmallEnginePower&TorqueRatingProcedure),andratingperformancehasbeenobtainedandcorrectedinaccordancewith

SAEJ1995(Revision2002-05).Torquevaluesarederivedat3060RPM;horsepowervaluesarederivedat3600RPM.Actualgrossengine

power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide

array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine

will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due

to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application

limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity

limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine.

Water Pump



Model 073034, 073035



Suction Port Diameter ...................... 5 cm (2 in)

Discharge Port Diameter .................... 5 cm (2 in)

Total Head...............................33m(108ft)

Maximum Head

Suction Lift.................................8m(26ft)

Discharge Lift .............................25m(82ft)

Maximum Discharge Capacity...435l/min(115USgal/min)

Shipping Weight ..........................17kg(38lb)



Displacement ........................127cc(7.74in

)

Bore ................................62mm(2.441in)

Stroke ..............................42mm(1.654in)

Oil Capacity....................0.54-0.59l(18-20oz)



Spark Plug Gap..................... 0.76 mm (0.030 in)

Spark Plug Torque ....................20Nm(180lb-in)

Armature Air Gap ........0.15 - 0.25 mm (0.006 - 0.010 in)

Intake Valve Clearance ...0.13-0.18mm(0.005-0.007in)

Exhaust Valve Clearance..0.13-0.18mm(0.005-0.007in)

*Enginepowerwilldecrease3.5%foreach300meters(1,000

ft)abovesealeveland1%foreach5.6°C10°F)above25°C

(77°F).Theenginewilloperatesatisfactorilyatanangleupto15°.



Oval Air Filter .............................................................797258

Fuel Additive ........................................................5041,5058

Resistor Spark Plug ...................................................797235

Spark Plug Wrench ............................................89838,5023

Spark Tester ................................................................19368

** We recommend that you see any Briggs & Stratton Authorized

Dealer for all maintenance and service of the water pump. Use

only genuine Briggs & Stratton parts.

Not for

Reproduction

Español

Português

Türkçe

Gracias por comprar esta bomba de agua de calidad Briggs & Stratton. Nos complace que haya depositado su confianza en la

marca Briggs & Stratton. Si se utiliza y mantiene de acuerdo con las instrucciones de este manual, su bomba de agua Briggs &

Stratton le proporcionará muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de las bombas de agua

y cómo evitarlos. Esta bomba de agua está diseñada sólo para transferir agua que pueda contener arena o cieno. No tiene

ningún otro fin. Es importante que lea y comprenda perfectamente estas instrucciones antes de intentar arrancar o utilizar este

equipo. .

Es necesario realizar el montaje final de la bomba de agua antes de usarla. Consulte las instrucciones sobre los

procedimientos de montaje final en la sección Montaje del presente manual. Siga las instrucciones detalladamente.



Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan

problemas relacionados con la compra en el futuro. Estos números se encuentran en el lugar mostrado en la Figura 1.

Fecha de compra

Bomba de agua

Número de modelo

Revisión del modelo

Número de serie

Motor

Número de modelo

Número de serie

material, sea cual sea la forma empleada para ello, sin el permiso previo y por escrito de Briggs & Stratton Power Products

Group, LLC.

Índice

Ilustraciones...................................................... 3

Instrucciones importantes de seguridad............................. 20

Montaje . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Funcionamiento .................................................. 24

Mantenimiento ................................................... 26

Resolución de problemas ......................................... 30

Garantías ....................................................... 31

 ..................................... 34

Not for

Reproduction

20 BRIGGSandSTRATTON.COM

Instrucciones importantes

de seguridad

CONSERVE ESTAS INSTRUCCIONES - Este manual

contiene instrucciones importantes que se deben seguir

durante el funcionamiento de la bomba de agua.

Símbolos sobre la seguridad



El símbolo de alerta de seguridad (

)

indica un posible

riesgo para su integridad física. Se utiliza una palabra de

señalización (PELIGRO, ADVERTENCIA o PRECAUCIÓN)

junto con el símbolo de alerta para designar un grado o nivel

de gravedad de riesgo. Se puede utilizar un símbolo de

seguridad para representar el tipo de riesgo. La palabra de

señalización AVISO se utiliza para hacer referencia a una

práctica no relacionada con una lesión física.

PELIGRO indica un riesgo que, de no evitarse, provocará

la muerte o lesiones de gravedad.

ADVERTENCIA indica un riesgo que, de no evitarse,

podría provocar la muerte o lesiones de gravedad.

PRECAUCIÓN indica un riesgo que, de no evitarse,

podría provocar lesiones leves o moderadas.

AVISO hace referencia a una práctica no relacionada con

una lesión física.

El fabricante no puede prever toda circunstancia que

conlleve un riesgo potencial. Por tanto, las advertencias

de este manual, así como las etiquetas y calcomanías

adheridas a la unidad, no incluyen todos los riesgos

posibles. Si utiliza un procedimiento o técnica de uso no

recomendado específicamente por el fabricante, deberá

asegurarse de que es seguro tanto para usted como para

otras personas. También deberá asegurarse de que la

técnica de uso que elija no hace que la bomba de agua

sea insegura.



A - Explosión F - Superficie caliente

B - Fuego G - Superficie resbaladiza

C - Descarga eléctrica H - Partes móviles

D - Vapores tóxicos J - Lea el manual

E - Retroceso

A B C

D E

G H

ADVERTENCIA Los motores en funcionamiento

producen monóxido de carbono, un gas venenoso

inodoro e incoloro.

La inhalación de monóxido de carbono puede

provocar dolor de cabeza, fatiga, mareos, vómitos,

confusión, convulsiones, náuseas, desmayos o

incluso la muerte.

Utilice la bomba de agua SÓLO a la intemperie.•

NO arranque ni deje funcionar el motor en interiores •

ni en zonas cerradas, aunque haya ventanas y

puertas abiertas.

Evite que los gases de escape entren en un espacio •

cerrado a través de las ventanas, puertas, tomas de aire

de ventilación u otras aberturas.

ADVERTENCIA El uso de la bomba de agua puede

producir charcos y superficies resbaladizas.

Utilice la bomba de agua desde una superficie estable.•

La zona debe tener inclinaciones adecuadas y sistema de •

drenaje para reducir la posibilidad de una caída debido a

superficies resbaladizas.

ADVERTENCIA El contacto con la zona del silenciador

puede producir quemaduras graves.

Los gases y el calor de escape pueden

inflamar los materiales combustibles y las

estructuras o dañar el depósito de combustible

y provocar un incendio.

No toque las piezas calientes y EVITE los gases de •

escape a alta temperatura.

Deje que el equipo se enfríe antes de tocarlo.•

Deje un espacio mínimo de 1.5 m (5 pies) alrededor de la •

bomba de agua, incluida la parte superior.

Not for

Reproduction

Sayfa yükleniyor ...

Simplicity 073034-0 Kullanım kılavuzu

Marka: Simplicity

Model: 073034-0

Kategori: Motorlu taşıt aksesuarları

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

MODEL 073034-0

PDF İndir

rapor

Diğer dillerde

español: Simplicity 073034-0 Manual de usuario
português: Simplicity 073034-0 Manual do usuário

Simplicity 073034-0 Kullanım kılavuzu

Bu kılavuz için de uygundur

Simplicity 073034-0 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler