Yamaha TSX-130 El kitabı

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

TSX-130

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

i

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

AVERTISSEMENT

L’utilisation de commandes et l’emploi de réglages ou de

méthodes autres que ceux décrits ci-dessous, peuvent

entraîner une exposition à un rayonnement dangereux.

VORSICHT

Die Verwendung von Bedienelementen oder die Einstellung

bzw. die Ausführung von anderen als in dieser Anleitung

beschriebenen Vorgängen kann zu Gefährdung durch

gefährliche Strahlung führen.

OBSERVERA

Användning av reglage eller justeringar eller utförande av

åtgärder på annat sätt än så som beskrivs häri kan resultera i

farlig strålning.

ATTENZIONE

L’uso di controlli, regolazioni, operazioni o procedure non

specificati in questo manuale possono risultare in esposizione

a radiazioni pericolose.

PRECAUCIÓN

El uso de los controles, los ajustes o los procedimientos que

no se especifican enste manual pueden causar una exposición

peligrosa a la radiación.

LET OP

Gebruik van bedieningsorganen, instellingen of procedures

anders dan beschreven in dit document kan leiden tot

blootstelling aan gevaarlijke stralen.

ПРЕДОСТЕРЕЖЕНИЕ

Использование органов управления или произведение

настроек или выполнение процедур, не указанных в

данной инструкции, может отразиться на выделении

опасной радиации.

CAUTION INVISIBLE LASER RADIATION WHEN OPEN

AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO

BEAM.

VORSICHT!

UNSICHTBARE LASERSTRAHLUNG TRITT

AUS, WENN DECKEL GEÖFFNET UND WENN

SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT IST.

NICHT DEM STRAHL AUSSETSEN!

VARNING

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR

FARLIG.

ADVARSEL

USYNLIG LASERSTRÅLING VED ÅBNING,

NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.

UNDGÅ UDSÆTTELSE FOR STRÅLING.

VAROITUS!

SUOJAKOTEL OA EI SAA AVATA. LAITE

SISÄLTÄÄ LASERDIODIN, JOKA LÄHETTÄÄ

(NÄKYMÄTÖNTÄ) SILMILLE VAARALLISTA LASER

SÄTEILYÄ.

ADVARSEL

USYNLIG LASERBESTRÅLING NÅR DENNE

DELEN ER ÅPEN OG SIKKERHETSSPERREN ER

UTKOBLET. UNNGÅ UTSETTELSE FOR STRÅLING.

● The name plate is located on the bottom of the unit.

ii

VAROITUS

Muiden kuin tässä esitettyjen toimintojen säädön tai asetusten

muutto saattaa altistaa vaaralliselle säteilylle tai muille

vaarallisille toiminnoille.

DK

Advarsel: Usynlig laserstråling ved åbning når

sikkerhedsafbrydere er ude af funktion. Undgå utsættelse for

stråling.

Bemærk: Netafbryderen SYSTEM OFF/Standby er sekundært

indkoblet og ofbryder ikke strømmen fra nettet. Den indbyggede

netdel er derfor tilsluttet til lysnettet så længe netstikket sidder i

stikkontakten.

N

Observer: Nettbryteren SYSTEM OFF/Standby er sekundert

innkoplet. Den innebygdenetdelen er derfor ikke frakoplet nettet

så lenge apparatet er tilsluttet nettkontakten.

S

Klass 1 laseraparat

Varning! Om apparaten används på annat sättþän i denna

bruksanvisning specificerats, kan användaren utsättas för osynlig

laserstrålning, som överskrider gränsen för laserklass 1.

Observera! Strömbrytaren SYSTEM OFF/Standby är sekundärt

kopplad och inte bryter inte strömmen från nätet. Den inbyggda

nätdelen är därför ansluten till elnätet så länge stickproppen sitter

i vägguttaget.

SF

Luokan 1 laserlaite

Varoitus! Laitteen käyttäminen muulla kuin tässä käyttöohjeessa

mainitulla tavalla saattaa altistaa käyttäjän turvallisuusluokan 1

ylittävälle näkymättömälle lasersäteilylle.

Oikeus muutoksiin varataan. Laite ei saa olla alttiina tippu-ja

roiskevedelle.

Huom. Toiminnanvalitsin SYSTEM OFF/Standby on kytketty

toisiopuolelle, eikä se kytke laitetta irti sähköverkosta.

Sisäänrakennettu verkko-osa on kytkettynä sähköverkkoon aina

silloin, kun pistoke on pistorasiassa.

■ For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the instructions

described below.

The plug severed from the mains lead must be destroyed, as a

plug with bared flexible cord is hazardous if engaged in a live

socket outlet.

■ Special Instructions for U.K. Model

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE.

ÄLÄ KATSO SÄ TEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD. BETRAKTA

EJ STRÅLEN.

Note

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the

terminal which is marked with the letter N or coloured

BLACK. The wire which is coloured BROWN must be

connected to the terminal which is marked with the letter L

or coloured RED.

Make sure that neither core is connected to the earth

terminal of the three pin plug.

iii En

1 To assure the finest performance, please read this manual

carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place

with at least 15 cm on the top, 10 cm on the left and right,

and 10 cm at the back of this unit

— away from direct

sunlight, heat sources, vibration, dust, moisture, and/or

cold.

3 Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes

from cold to hot (or vice versa), and do not locate this

unit in an environment with high humidity (i.e., a room

with a humidifier) to prevent condensation inside this

unit, which may cause an electrical shock, fire, damage to

this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall

onto this unit and/or this unit may be exposed to liquid

dripping or splashing. On the top of this unit, do not

place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e., candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may fall and

liquid may cause electrical shock to the user and/or

damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all

connections are complete.

8 Do not operate this unit upside-down. It may overheat,

possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might

damage the finish.

12 Only voltage specified on this unit must be used. Using

this unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. Yamaha will not be held responsible for any

damage resulting from use of this unit with a voltage

other than specified.

13 To prevent damage by lightning, keep the power cable

and outdoor antennas disconnected from a wall outlet or

this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact

qualified Yamaha service personnel when any service is

needed. The cabinet should never be opened for any

reasons.

15 When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug from

the wall outlet.

16 Be sure to read the “TROUBLESHOOTING” section on

common operating errors before concluding that this unit

is faulty.

17 Before moving this unit, press ON/OFF to set the system

to off, and disconnect the AC power plug from the wall

outlet.

18 Condensation will form when the surrounding

temperature changes suddenly. Disconnect the power

cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may

become warm. Turn the system off, then leave this unit

alone for cooling.

20 Install this unit near the wall outlet and where the AC

power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such

as sunshine, fire or the like.

LASER SAFETY

This unit employs a laser. Due to possible eye injury, only a

qualified service person should remove the cover or attempt to

service this device.

DANGER

This unit emits visible laser radiation when open. Avoid direct

eye exposure to beam. When this unit is plugged into the wall

outlet, do not place your eyes close to the opening of the disc tray

and other openings to look into inside.

Caution: Read this before operating your unit.

This unit is not disconnected from the AC power source as

long as it is connected to the wall outlet, even if this unit itself

is turned off by ON/OFF. In this state, this unit is designed to

consume a very small quantity of power.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO

NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

The laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

LASER

Type Semiconductor laser GaAS/GaAlAs

Wave length 780 nm

Output Power 10 mW

Beam divergence 60 degrees

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

Taking care of the unit

When you wipe this unit, use a clean dry cloth.

1 En

English

PREPARATION OPERATION

ADDITIONAL

INFORMATION

PREPARATIONS BEFORE USING THIS UNIT

.............................................................................. 2

Turning on/off the system.......................................... 4

Adjusting the clock.................................................... 4

USING USEFUL FUNCTIONS ............................ 5

Using the alarm functions.......................................... 5

Setting sleeping mode................................................8

Setting Dimmer mode................................................ 8

Switching DSP mode................................................. 8

BASIC OPERATION............................................. 9

LISTENING TO MUSIC..................................... 10

Listening to your iPod™ ......................................... 10

Listening to a CD..................................................... 12

Listening to a USB device....................................... 13

LISTENING TO FM RADIO STATIONS ........ 14

Connecting antennas................................................ 14

Tuning radio stations ............................................... 14

Presetting radio stations........................................... 14

Selecting preset radio stations (Preset tuning)......... 15

Receiving Radio Data System stations.................... 15

TROUBLESHOOTING .......................................17

General..................................................................... 17

iPod™...................................................................... 18

Disc playback .......................................................... 18

USB playback .......................................................... 19

Radio reception........................................................ 19

Remote control ........................................................ 19

NOTES ON DISCS AND USB DEVICES ..........20

Disc information...................................................... 20

Handling a disc ........................................................ 20

About MP3 or WMA files....................................... 20

GLOSSARY...........................................................21

SPECIFICATIONS...............................................21

CONTENTS

PREPARATION

OPERATION

ADDITIONAL INFORMATION

■ About this manual

• In this manual, operations that can be performed with either this unit or its remote control are explained using the unit.

• The symbol “

☞” with page number(s) indicates the corresponding reference page(s).

• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.

• This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

■ Supplied accessories

This product includes the following accessories. Make sure you have all of the following parts.

DESKTOP AUDIO SYSTEM

SYSTEME AUDIO DESKTOP

TSX-130

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

G

Indoor FM antenna

(1.4 m (55-1/8”))

Remote control

Owner’s manual

2 En

PREPARATION

1 Source buttons: USB, CD, FM, iPod (☞ P. 9)

2 ON/OFF: System on/off (☞ P. 4)

3 VOLUME: Volume control buttons (☞ P. 9)

4 Audio control buttons (☞ P. 9)

5 iPod dock (☞ P. 10)

6 USB port (☞ P. 13)

7 OPEN/CLOSE : Disc tray open/close (☞ P. 12)

8 Alarm control buttons (☞ P. 5)

9 SNOOZE/SLEEP (☞ P. 7, 8)

0 Speakers

A Disc tray (☞ P. 12)

B Front panel display (☞ P. 4)

C To the wall outlet

D FM control buttons (☞ P. 14)

E CLOCK SET (☞ P. 4)

F FUNCTION

G DISPLAY (☞ P. 11, 12, 13)

H FOLDER S/T (☞ P. 9)

I DSP: DSP mode switching (☞ P. 8)

J Infrared signal transmitter (☞ P. 3)

K SLEEP: Sleep time setting (☞ P. 8)

L MENU S/T /Center buttons* (☞ P. 10)

M RANDOM/REPEAT: Changing the playback mode for

iPod/CD/USB (☞ P. 10, 12)

* The round shaped button on the center is called Center in this

manual.

PREPARATIONS BEFORE USING THIS UNIT

English

3 En

PREPARATION

■ Before using the remote control

■ Using the remote control

■ Replacing the battery in the remote control

Change the battery when the operation range of the remote control decreases.

• Insert the battery according to the polarity markings (+ and –).

• If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak.

• If a battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing.

• Before inserting new batteries, wipe the compartment clean.

• Dispose of batteries according to your regional regulations.

Notes

1 Remove the battery insulation sheet before using the remote

control.

2 Remove the transparent sheet before using the remote control.

Use the remote control within 6 m (20’) of this unit and point it

toward the remote control sensor.

• Do not spill liquid on the remote control.

• Do not drop the remote control.

• Do not leave the remote control in the following places:

– hot or humid places such as a bathroom or near a heater

– extremely cold places

– dusty places

Notes

Within 6 m

(20’)

Use a straight pin to remove

the cover.

Replace the battery with

a new CR2025 battery.

Close the cover.

PREPARATIONS BEFORE USING THIS UNIT

4 En

1 Connect the power cable to the wall

outlet.

2 Press ON/OFF to turn on the system.

y

• This unit has an auto off function, which will automatically

switch the system to off if the system is left turned on for 1 hour

without playback or any other operation being performed. This

function is not available when the source is set to FM.

• Press and hold ON/OFF on the top of the unit for more than 3

seconds to set the system to standby mode. All the information

on the front panel display is not displayed in standby mode.

This can reduce the power consumption. To cancel standby

mode, press ON/OFF.

• Even in system off/standby mode, the alarm function is

available.

• The memory back-up circuit prevents stored data such as the

time setting from being lost even in system off/standby mode.

The clock is not set at the factory.

1 Press CLOCK SET.

2 Select each setting with MENU S/T

and confirm with Center.

You can set YEAR → MONTH → DAY → TIME.

• This operation can be performed only with the remote control.

• Time appears in 12-hour notation (AM/PM), depending on the

model. For example, “4:00PM”.

• You can switch 12-hour/24-hour notation by pressing

FUNCTION → MENU S/T → Center to select TIME

FORMAT, then pressing MENU S/T → Center to select

12H/24H.

• The time settings are lost after one week when the power cable

is disconnected from the wall outlet.

Turning on/off the system

When the system is on: “Hello” appears, then clock and

other information are displayed.

When the system is off: “Good-bye” appears, then only

date and time are displayed.

Example: iPod playback mode display

Adjusting the clock

Notes

English

5 En

OPERATION

The unit has the dual alarm function. Each alarm time

always appears on the right/left sides of the clock on the

front panel display. When the alarm is set to on, the alarm

indicator and time light up.

You can set the different music to the alarm from what

you listen to during the setting.

This operation can be performed only with the buttons on the top

of the unit.

■ Setting the alarm time and sound

To cancel the alarm function setting during the operations, press

SETUP1/SETUP2. The alarm is not set.

1 Start setting ALARM1/ALARM2.

When you want to set the alarm to ALARM1, set on

SETUP1, and SETUP2 is for ALARM2.

2 Set the alarm time.

1 While setting the alarm function, the alarm

indicator blinks.

2 The item you are setting also blinks.

3 The > mark on the right side means that you have

other menu items on the following screens. You

can go to the next menu item setting by pressing

ENTER.

3 Select and set TYPE → BEEP →

SOURCE → VOLUME.

1 After setting the alarm time, select the alarm type

from BEEP/BEEP+MUSIC/MUSIC.

– BEEP: beep sound only

– BEEP+MUSIC: beep sound and music selected

in an input source, iPod/FM/CD/USB

– MUSIC: music only

If you set TYPE to BEEP+MUSIC, you can play

back the desired music in an input source, iPod/

FM/CD/USB and beep sound together at the time

you set. The music volume gradually increases to

wake you up comfortably, and then the beep

sound plays back at the time you set.

USING USEFUL FUNCTIONS

Using the alarm functions

Note

USING USEFUL FUNCTIONS

6 En

2 Select the beep sound.

5 kinds of beep sounds are stored on the unit.

The BEEP screen is skipped automatically if you

select MUSIC/BEEP+MUSIC in step 1.

y

You can preview the currently displayed beep sound by

pressing SNOOZE/SLEEP when you select the beep

sound. To stop the beep sound, press SNOOZE/SLEEP

again.

3 Select the music source from iPod/FM/CD/USB

or LAST SET.

The SOURCE screen is skipped automatically if

you select BEEP in step 1.

iPod

You can select PLAYLIST or RESUME PLAY.

The music starts from the beginning of the

playlist. Before this operation, make a playlist on

your iPod (☞ P. 7).

Select and set RESUME PLAY when you want to

resume the music, which you listen to last time, as

the alarm sound.

CD

Audio CD: Set a track number.

MP3/WMA CD: Set a folder number. Music starts

from the beginning of the selected folder

(☞ P. 20).

USB (MP3/WMA files)

Set a folder number. Music starts from the

beginning of the selected folder (☞ P. 20).

FM

Set preset number/frequency.

LAST SET

Keep the setting you set last time.

If the SOURCE is not set completely or the music device is

not set, the unit plays back the beep sound instead. For

example, if the unit cannot read your iPod, the beep sound

plays back.

4 Set the alarm volume.

The volume is set with ENTER in step 4, then the

alarm setting is complete. The alarm is set to on

automatically.

■ Switching on/off the alarm

You can switch on/off the alarm with ALARM1/

ALARM2, but the alarm settings are not deleted with this

operation.

Switch on/off the alarm function.

When the alarm is on, the alarm indicator and time light

up.

Select and set PLAYLIST.

Select and set the desired playlist.

Note

USING USEFUL FUNCTIONS

English

7 En

OPERATION

■ Using the snooze function

When the beep sound, music, or both are played back, you

can set the snooze function.

Set the snooze function.

The function differs depending on the alarm type you set

in TYPE (☞ P. 5).

BEEP: The beep sound stops by pressing SNOOZE/

SLEEP, and resumes after 5 minutes.

MUSIC: The music stops by pressing SNOOZE/SLEEP,

and resumes after 5 minutes.

BEEP+MUSIC: With one click of SNOOZE/SLEEP,

you can stop the beep sound and keep playing back the

music. The beep sound resumes after 5 minutes.

y

You can also set the snooze function by pressing SLEEP on the

remote control instead of SNOOZE/SLEEP on the unit.

■ Stopping the alarm sound

You can stop the alarm sound in the 3 ways as follows.

When you stop alarm sound, the system is set to off.

Press ALARM1/ALARM2.

Press ON/OFF.

Press and hold SNOOZE/SLEEP for 2

seconds.

y

• If you do not stop the alarm, the alarm stops after 60 minutes

automatically.

• When you stop the alarm, the alarm indicator disappears. To

activate the alarm function again, press ALARM1/ALARM2 to

set the alarm to on.

• When you stop the alarm, the time setting, etc., is saved for

convenient use next time.

Any operations other than setting the snooze function, stopping

the alarm sound, or adjusting the volume control are not available

while playing back the alarm sound.

■ About Playlist

You can collect your favorite songs in the library on your

iPod and make a list. This is a playlist. If you select a

playlist for playback, the songs in the playlist will be

played back. Even if you delete a song in a playlist, it is

not deleted from the library.

y

For more details on playlists, refer to the instruction manual of

your iPod.

Note

USING USEFUL FUNCTIONS

8 En

You can set the time to turn off the system automatically.

Select the sleep time.

When the sleep function is on, the SLEEP indicator lights

up.

y

You can also operate this function with SLEEP on the remote

control.

You can change the brightness of the front panel.

If you set DIMMER to AUTO, the dimmer level is

adjusted automatically, depending on the brightness of the

room. If your room is dark, the front panel becomes

darker.

y

The default setting is AUTO.

1 Select DIMMER from the FUNCTION

menu.

y

After you select DIMMER with Center, < appears on the

left side of the front panel display. You can go back to the

FUNCTION menu by pressing MENU on the remote

control.

2 Select the desired dimmer level.

You can switch the sound mode according to the

environment or your preference.

Switch DSP mode.

Each time you press DSP the setting switches as follows:

NORMAL: For normal sound

↓

MILD: For natural and mild sound

↓

HEAVY: For more powerful sound

(default setting)

↓

LIVE: For wide realistic sound

↓

Back to NORMAL

Setting sleeping mode

Setting Dimmer mode

Press repeatedly.

Switching DSP mode

Press repeatedly.

English

9 En

OPERATION

*

1

Even when the system is off, you can start playback of the desired source by pressing one of the Source buttons, without pressing

ON/OFF.

*

2

Playback is resumed from it was last stopped.

(Except for CD/USB which are played back from the beginning of the track you listened to last time.)

Only for CD/USB:

If you press while the music is stopped, the resume information is cleared and the music starts from the beginning of the first

track/file next time.

*

3

Only for MP3/WMA of CD and USB

BASIC OPERATION

:Press to turn off the

sound. Press again to

resume the volume.

:Press to choose a

folder.*

3

:Press one of the Source buttons to select the desired source.

*1*2

:Press to play/pause.*

2

:Press to stop playback.*

2

: Press to skip backward/forward.

:Press to control the volume.

10 En

• The unit is compatible with iPod touch, iPod (Click Wheel

including iPod classic), iPod nano and iPod mini.

• You can remove your iPod whenever you want.

• Some features may not be available depending on the model or

the software version of your iPod.

■ Playing back normally

1 Set your iPod into the iPod dock.

• A compatible Dock Adapter (not supplied) is required to

attach to the unit.

• The iPod may not be set in the iPod dock securely if it is in

its protective case.

2 Select iPod.

Playback starts.

y

For operations of your iPod, refer to the instruction manual of

your iPod.

■ Selecting music on iPod with the remote

control

You can also operate with your iPod only when LIST

DISP is set to iPod (☞ P. 11).

MENU: Go back to the previous menu.

Center: Confirm.

S/T: Select menu or items.

■ Using shuffle/repeat mode

After the above steps 1 and 2, you can enjoy shuffle and

repeat mode.

Press RANDOM to switch shuffle mode

for iPod.

You cannot set ALBUM when you use an iPod touch.

Switch repeat mode.

LISTENING TO MUSIC

Listening to your iPod™

Notes

iPod

Dock Adapter

Note

Press repeatedly.

LISTENING TO MUSIC

English

11 En

OPERATION

■ Switching the playback information

display

Switch the display in iPod playback

mode.

You can change the information display as follows.

Song number and elapsed time (default setting)

↓

Song number and remaining time

↓

Song name

↓

Artist name

↓

Album name

↓

Back to the default setting

• This function is available for iPod touch, iPod classic, iPod 5

th

generation or later, and iPod nano. However, even with these

models, this function may not be available depending on the

software version of your iPod.

• If you intend to disconnect the power cable of the unit for a long

time, remove the iPod from the unit.

■ Switching the playback list display

LIST DISP allows you to select iPod or the front panel

display of the unit to display the list.

If you set LIST DISP to iPod, you can also control

playback operations and display the menu list on the iPod.

y

The default setting is iPod.

When LIST DISP is set to F.PANEL, playback operation and

menu list displaying are available only on the unit. These

operations are not available with your iPod.

1 Select LIST DISP from the

FUNCTION menu.

2 Select iPod/F.PANEL.

Notes

Press repeatedly.

Note

Example: When LIST DISP is set to F.PANEL

LISTENING TO MUSIC

12 En

■ Playing back normally

1 Open the disc tray and insert your

disc.

2 Close the disc tray.

3 Select CD.

Playback starts.

■ Playing back in random sequence/

repeatedly

After the above steps 1 to 3, you can enjoy random and

repeat mode.

Switch random mode.

Switch repeat mode.

If the selected music source contains folders, you can also

select FOLDER.

■ Switching the playback information

display

Switch the display in CD playback

mode.

You can change the information display as follows.

Elapsed time of the current track (default setting)

↓

Remaining time of the current track

*1

↓

Total time of the disc

*1

↓

Remaining time of the disc

*1

↓

Track name

*2

↓

Artist name

*2

↓

Album name

*2

↓

File name

*3

↓

Back to the default setting

*

1

Only for Audio CDs

*

2

Only when the selected track has information

*

3

Only for MP3/WMA CDs

Listening to a CD

Press repeatedly.

LISTENING TO MUSIC

English

13 En

OPERATION

You can remove your USB device whenever you want.

■ Playing back normally

1 Set your USB device into the USB

port.

This unit supports USB mass storage class devices

(e.g., flash memories or portable audio players) using

FAT16 or FAT32 format.

• Some devices may not work properly even if they meet the

requirements.

• Do not connect devices other than USB mass storage class

devices (such as USB chargers or USB hubs), PCs, card

readers, an external HDD, etc.

• Yamaha will not be held responsible for any damage to or

data loss on the USB device occurring while the device is

connected to this unit.

• Playability of and power supply to all kind of USB devices

are not guaranteed.

2 Select USB.

Playback starts.

The reading time may exceed 30 seconds, depending on the

number of files/folders.

■ Playing back in random sequence/

repeatedly

After the above steps 1 and 2, you can enjoy random and

repeat mode.

Set in the same way as for CDs (☞ P. 12).

■ Switching the playback information

display

Switch the display in USB playback

mode.

You can change the information display as follows.

Elapsed time of the current track (default setting)

↓

Track name

*

↓

Artist name

*

↓

Album name

*

↓

File name

↓

Back to the default setting

* Only when the selected file has information

y

On MP3/WMA files, refer to “NOTES ON DISCS AND USB

DEVICES” (☞ P. 20).

Listening to a USB device

Note

Notes

Note

Press repeatedly.

14 En

• The antenna should be stretched out.

• If radio reception is poor, change the height, direction, or

placement of the antenna.

• If you use an outdoor antenna instead of the supplied FM

antenna, reception will be better.

1 Turn on FM.

2 Start automatic tuning.

y

If the signal received from the station you want to select is

weak, you can also tune into radio stations manually by

pressing TUNING<</>> repeatedly.

If you tune to a station manually, the sound is monaural.

You can store your favorite FM stations with the preset

function.

■ Auto preset

1 Press and hold MEMORY for more

than 2 seconds in FM mode.

2 Start the auto preset.

■ Manual preset

1 Tune into a favorite radio station.

2 Press MEMORY.

LISTENING TO FM RADIO STATIONS

Connecting antennas

Notes

Tuning radio stations

Note

Indoor FM antenna

(supplied)

Press and hold.

Presetting radio stations

LISTENING TO FM RADIO STATIONS

English

15 En

OPERATION

3 Select the preset number you want

to store to.

To cancel the manual preset, press MEMORY again.

4 Complete the manual preset.

y

• You can preset up to 30 FM stations.

• You can delete a preset station by pressing FUNCTION →

MENU S/T → Center to select PRESET DELETE.

When you perform the auto preset, all stored stations are cleared

and the new stations are stored.

Select the preset radio station in FM

mode.

y

You can also use / on the top of the unit.

■ Selecting stations by program type

1 While receiving FM, select PTY SEEK

from the FUNCTION menu.

2 Select a program type.

3 Initiate scan.

Note

Selecting preset radio stations

(Preset tuning)

Receiving Radio Data System

stations

LISTENING TO FM RADIO STATIONS

16 En

■ Available program types

■ Switching the information display of

Radio Data System

While receiving Radio Data System,

switch the information display.

Station name

↓

Program type

↓

Text information related to the station

↓

Current time

↓

Original display

↓

Status display

If the signal transmission of the Radio Data System station is too

weak, this unit may not be able to receive Radio Data System

information completely. In particular, RT (Radio Text)

information uses a lot of bandwidth, so it may be less available

compared to other types of information.

■ Adjusting the time automatically

This function sets the clock automatically based on RDS

information.

1 While receiving FM, select AUTO

CLOCK from the FUNCTION menu.

2 Select and set the desired setting.

The clock information may differ depending on the received

station.

Program type Descriptions

News

Current Affairs

Information

Sport

Education

Drama

Cultures

Culture

Science

Varied Speech

Varied

Pop Music

Rock Music

Easy Listening

Easy Listening Music

Light Classics M

Light Classical Music

Serious Classics

Serious Classical Music

Other Music

Note

Press repeatedly.

Note

Sayfa yükleniyor...

Yamaha TSX-130 El kitabı

Yamaha TSX-130 El kitabı

diğer dillerde

İlgili makaleler

Diğer belgeler