Druck 542F Yükleme Rehberi

Druck.com

ADTS

542F/552F/553F/554F

Air Data Test Set

Safety and Installation Guide

English 1 – 12

Dansk 13 – 24

Deutsch 25 – 38

Español 39 – 50

Français 51 – 64

Italiano 65 – 78

Lietuvių 79 – 90

Norsk 91 – 102

Português 103 – 114

Türkçe 115 – 126

Русский 127 – 140

中文 141 – 154

日本語 155 – 168

English–ADTS Safety and Installation Guide | 1

1. Introduction

This manual is applicable to ADTS542F/552F/553F and 554F, referred to as ADTS, and provides

safety and installation information for the Air Data Test Set, compatible with the requirements of

first line operation.

A touchscreen (ADTS Touch) is used to control all required functions. The ADTS Touch can be

positioned on the ADTS or used as a hand held mobile unit via a cable or Bluetooth® wireless

technology. This allows a person to complete the entire test program remotely while conveniently

seated in the aircraft. An ADTS Touch-ER option can be purchased for robust wireless

communications in a large body aircraft. The ADTS Touch can be powered when positioned on

the ADTS, or using a cable connection to the ADTS or battery powered.

The manufacturer has designed this equipment to be safe when operated using the procedures

detailed in this manual.

For details of calibration requirements for the ADTS, refer to User Manual K0553.

For details of available manufacturer specified parts, refer to the current revision of the product

data sheet.

Service/maintenance and repair will be carried out at Druck authorized service centers.

1.1 Markings and Symbols

For the list of Druck approved service centers, go to:

Druck.com

Symbol Description

This equipment meets the requirements of all relevant European safety directives.

The equipment carries the CE mark.

This symbol, on the equipment, indicates that the user should read the user manual.

This symbol, on the equipment, indicates a warning and that the user should refer to

the user manual.

This symbol warns the user of the danger of electric shock.

Do not dispose of this product as household waste. Use an approved organization

that collects and/or recycles waste electrical and electronic equipment. For more

information, contact our customer service department, or your local government

office.

The Bluetooth® wireless technology word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by Druck is under license.

Other trademarks and trade names are those of their respective owners.

2 | ADTS Safety and Installation Guide–English

1.2 Intended Use

Test and calibration of aircraft aeronautical pressure instruments located indoor in a hanger or

calibration laboratory or outdoor (non-continuously) on a runway, refer to User Manual K0553 for

further information.

If the equipment is used in a manner not specified by this document and K0553 the protection

provided by the equipment may be impaired.

1.3 Safety

Examine all equipment to be used, paying particular attention to electrical leads and connectors

and pneumatic pipes and connectors. DO NOT use any equipment that is known to be or

suspected to be damaged or faulty.

1.4 Power Supply

1.5 Power Supply Connection

Do not apply electrical power outside the values stated.

Make sure that the power supply is off before connecting the power cable.

The ADTS must be connected to the correct electrical power supply as stated, adjacent to the

power connector.

1.6 Fuses

The two High Breaking Capacity fuses (8) (see Figure 6), located in the holders and mounted on

the front panel, protect the unit. The fuses are connected in the live and neutral supply circuit and

are rated at: T5AH 250V.

1.7 Replacing a Fuse

1. Disconnect the electrical power supply.

2. Unscrew the fuse holder cap from the front panel and remove the fuse.

3. Fit a new fuse of the correct size and rating into the fuse holder cap.

4. Secure the fuse holder cap in the front panel.

WARNING This equipment is not rated for use in potentially explosive

atmospheres. Using this equipment in a potentially explosive atmosphere could

lead to serious injury or death.

Single phase 110/230 Vac, 50/60Hz

115 Vac, 400Hz

200 VA Max - ADTS542F/ADTS552F

300 VA Max - ADTS553F/ADTS554F

RISK OF ELECTRIC SHOCK There is a risk of electric shock/electrocution

if there is not a protective earth in place. The ADTS must, at all times, be

connected to the supply protective earth/ground.

The power supply cable and connector must be correctly rated for the power

supply. Only use power cables supplied by Druck specifically for the ADTS.

European Color US Color Function

Brown Black Live

Blue White Neutral

Green/Yellow Green Protective Earth (Ground)

English–ADTS Safety and Installation Guide | 3

2. ADTS Touch

The ADTS Touch is used to control all required functions. The ADTS Touch can be positioned on

the ADTS or used as a hand held mobile unit via a cable or Bluetooth® wireless technology.

The ADTS Touch will have power applied when:

• Positioned (docked) (1) on a powered-on ADTS.

• Using an umbilical cable connected to a powered-on ADTS.

• Powered from its own battery pack.

• Powered from a universal power supply unit

Figure 1: ADTS Touch Docking Connector

The ADTS Touch is equipped with an On/Off switch (2) and USB connectors for connection to a

PC or mass storage device (3).

Figure 2: Touch On/Off Switch and USB Connectors

Connector (4) allows connection between the base unit and the ADTS Touch using a 5 metre or

18 metre umbilical cable.

Note: Only use cables that have been supplied by or purchased from Druck.

1

32

4 | ADTS Safety and Installation Guide–English

Figure 3: ADTS Touch Umbilical Cable Connector

The ADTS Touch can contain one Lithium-ion battery which is housed in the battery compartment

of the ADTS Touch.

2.1 Replacing the Battery

Figure 4: ADTS Touch Battery Compartment

Note: Only use batteries that have been supplied by or purchased from Druck.

Prior to replacing the battery, switch the ADTS Touch off. If the ADTS Touch is connected to the

umbilical cable or Docking connector, disconnect prior to removing the battery cover plate.

1. Unscrew the two thumbscrews (5) of the battery compartment cover plate and remove the

cover plate.

2. Use the tab attached to the battery to slide the battery out of the battery compartment.

3. Fit a new or re-charged battery into the battery compartment, observing the keyed

orientation.

CAUTION When the battery compartment cover plate is removed and the

ADTS touch is tilted with the battery compartment facing downwards, the battery

can fall out of the ADTS touch causing damage to the battery.

4

55

English–ADTS Safety and Installation Guide | 5

Note: The battery does not necessarily need to be new or re-charged. The ADTS Touch will

function safely and correctly with a flat battery when the umbilical cable or dock charging

supply is connected.

4. Refit the battery compartment cover plate and tighten the two thumbscrews (5). The cover

must be fitted correctly to maintain protection afforded.

2.2 Battery Care and Maintenance

The battery unit contains a Lithium-ion battery which requires no user maintenance. If shipping

an ADTS Touch and/or battery unit please contact your local service center beforehand for

shipping requirements. Battery must be removed from the ADTS Touch during transportation.

Prolonged exposure to temperature extremes may significantly reduce battery lifetime. For

maximum lifetime, avoid prolonged periods where the battery is exposed to temperatures outside

the range -30°C to +45°C.

The recommended storage temperature range is 5°C to 21°C (41°F to 98.8°F).

The battery is removable. The manufacturer makes the following safety recommendations. The

user should not:

• Short circuit the battery.

• Immerse the battery in any liquid.

• Disassemble or deform the battery.

• Expose to, or dispose of the battery in a fire.

• Subject the battery to excessive physical shock or vibration outside the specified limits for

the ADTS.

• Use a battery that appears to have suffered abuse.

• Charge with an unspecified charger or specified charger that has been modified. This can

cause breakdown of the battery or swelling and rupturing.

• Use a battery in an appliance or purpose for which it was not intended.

The battery unit is sealed for life, so leakage of electrolyte is not expected. If leakage of electrolyte

from the battery is observed, stop using the battery immediately and avoid contact with the

electrolyte. If skin or clothes come into contact with the electrolyte, wash immediately with soap

and water. If electrolyte comes into contact with the eyes, wash the eyes thoroughly with water

and consult a doctor immediately.

The ADTS5xxF, ADTS Touch and ADTS Touch-ER contain a Lithium-ion coin cell. This coin cell

is not user replaceable. Installation and replacement shall only be performed by trained

personnel.

Always dispose of batteries safely and in accordance with local instructions.

2.3 Battery Charging

The battery in the ADTS Touch can be charged using one of the following methods:

• By placing the ADTS Touch onto a powered ADTS.

• By connecting the ADTS Touch connector (4) (see Figure 3) to the ADTS using the umbilical

cable.

• By using the AATOUCH-5 optional accessory desktop charger. The battery must be

removed from ADTS Touch when it is charged by the AATOUCH-5 desktop charger.

6 | ADTS Safety and Installation Guide–English

• Using a universal power supply unit connected to the ADTS Touch using an adapter:

Figure 5: Universal Power Supply Unit and Adapter

The ADTS Touch universal power supply and the desktop charger are both rated for indoor use

only.

English–ADTS Safety and Installation Guide | 7

3. ADTS5xxF

Figure 6: ADTS542F Front Panel

Note: See Figure 8 for other variants.

3.1 Power-Up Test (see Figure 6)

1. Fit “Pitot” (Pt) (1) and “Static” (Ps) (2) port blanks.

2. Ensure that the test set is connected to an external power supply and the supply is switched

on.

3. Use the On/Standby Switch (3) on the front of the test set to switch the test set on. The test

set performs a self test, resulting in a test set status indication (4a) “Pass” or “Fault”.

1

3

6

2 4

57

8

8 | ADTS Safety and Installation Guide–English

The test set status indications are as follows:

Figure 7: Test Set Status Indications

If the self test fails, or for any other reason the test set is considered to be unserviceable,

contact Druck and return the test set to the Druck or Druck approved service center.

Test Set Status Indications (4):

4a

Power on and self test:

• Off (Power Off)

• Standby (Yellow)

• Self test in Progress (flashing Green)

• Pass/Ready (Green)

• Fault (Red)

4b

Battery pack status (if fitted - ADTS542F only):

• For LED indications, see User Manual K0553 “ADTS542F Battery Pack”

Note: Battery pack is currently not a purchasable option.

4c

Bluetooth® wireless technology connection status:

• Wireless connection present (Blue)

• Wired connection and Bluetooth® option enabled (Flashing blue)

• Fast flash - enabled and visible for pairing (available for 5 minutes after power-up)*

• Slow blink - enabled but not visible for pairing*

• Bluetooth® option disabled (Wireless LED off)

• Initialization fault (Red) *

• * Only applicable to base unit software variant DK0467

Note: The “fast flash” state also occurs when switching the ON/standby switch from

standby to ON. If the Bluetooth® link drops during use then “fast flash” will resume. This

occasionally requires the unit to be returned to standby mode before the link can be re-

established.

4d

Aircraft status:

• When the ADTS is controlling the aircraft and it is “off ground”, the LED will be Yellow.

• When the ADTS is controlling the aircraft to “going to ground”, the LED will flash

Yellow.

• When the ADTS has made the aircraft “safe at ground”, the LED is Green.

• In standby-mode, this LED will be off.

4a 4b 4c 4d

English–ADTS Safety and Installation Guide | 9

4. To disconnect power to the test set, either:

a. Remove the power cable (5) from the front of the test set, or

b. Remove the power cable from the wall socket. The wall socket connection must remain

accessible.

3.2 External Functional Earth/Ground Terminal

An external earth/ground connection stud (6) is available as a functional earth on the front panel

providing a connection/bonding point for other equipment to be connected to the same

earth/ground connection as the test set (This is not a protective earth/ground connection).

3.3 Pneumatic Connections

No external pneumatic pressures or vacuums are required as the ADTS contains internal

pressure and vacuum pumps.

Hoses (available as orderable accessories on the datasheet) are used for connection to the

“Pitot” (Pt) (1) and “Static” (Ps) (2) output ports of the ADTS.

The “Pitot” (Pt) and “Static” (Ps) outputs can then be connected to the corresponding Pitot and

Static connectors on the aircraft or aeronautical instruments.

The maximum Pt and Ps output pressure is 2 bar absolute.

The following table details the possible connector specifications:

Mating female parts are available from Druck.

3.4 Cleaning

The following materials are approved cleaning agents:

Note: Equivalent alternatives may be used for listed items.

WARNING The On/Standby Switch (3) on the front of the test set is not a

disconnecting device.

Name Specification

G1/8 Pipe Thread ISO 228 - G 1/8 B

AN3 3/8 - 24 UNJF - 3A Thread

AN4 7/16 - 20 UNJF - 3A Thread

AN6 9/16 - 18 UNJF - 3A Thread

CAUTION Do not use solvents to clean this equipment.

Material Specification

Lint-free cloth Commercially available

Damp cloth -

Mild detergent Commercially available

Soft brush Commercially available

10 | ADTS Safety and Installation Guide–English

1. Clean the external surfaces of the unit using lint-free cloth and a soft brush. Remove

stubborn dirt using a damp cloth and mild detergent and allow to dry.

2. Clean the electrical connector using a soft brush. Remove stubborn dirt using a damp cloth

and mild detergent and allow to dry.

4. Specification

4.1 Operating Environment

WARNING This equipment is not rated for use in potentially explosive

atmospheres.

Storage temperatures ADTS542F: -20°C to 70°C (-4° to 158°F)

ADTS552F )

ADTS553F ) -20°C to 70°C (-4° to 158°F)

ADTS554F )

Operating

temperatures/environment

ADTS542F: -5°C to 50°C (32° to 122°F)

ADTS552F )

ADTS553F ) -5°C to 50°C (32° to 122°F)

ADTS554F )

Operating humidity: 5% to 95% RH (condensing)

Indoor & Outdoor (non-continuously) use

ADTS Touch universal power

supply

Operating temperature: 10°C to 50°C (50° to 122°F)

Operating humidity: 5% to 95% RH (non-condensing)

Power supply Universal input Mains Power Supply.

Class 1 equipment requiring a protective earth connection.

TXAH 250V HRC Time-delay (T) 250Va.c. rated fuses (X = amp

rating of fuse).

Overvoltage category II, Pollution degree 2

The supplied mains/PSU cable protective earth/ground conductor

must be connected to the power supply protective earth/ground

system.

Electrical safety EN 61010-1, UL 61010-1, CSA 22.2, No. 61010-1 and IEC 61010-1

Operating altitude Maximum 7500ft (2300 metres)

Ingress protection ADTS542/552/553/554 IP33, ADTS Touch IP65 (EN60529)

English–ADTS Safety and Installation Guide | 11

4.2 Dimensions

Figure 8: ADTS 5xxF Variants

WARNING The ADTS can be moved by use of the handle and wheels. if the

ADTS is to be lifted, it must be lifted by at least two people.

ADTS5xxF Weight ADTS542F: 14kg (31lb) (without battery, estimated as

20kg (44lb) with battery)

ADTS552F: 22kg (48.5lb)

ADTS553F: 23.5kg (52lb)

ADTS554F: 24.5kg (54lb)

Height 300mm

Depth ADTS542F: 320mm (front to rear)

ADTS55xF: 425mm (front to rear)

Width ADTS542F: 420mm (left to right)

ADTS55xF: 525mm (left to right)

ADTS Touch Weight 1kg (2.2lb)

1.4kg (3lb) with battery

Height 58mm

Depth 154mm

Width 224mm

ADTS542F

ADTS553F ADTS554F

ADTS552F

12 | ADTS Safety and Installation Guide–English

4.3 Product Labeling

The product label for the base unit can be found in the bottom right hand corner of the front panel.

The product label for the ADTS Touch can be found on the rear of the ADTS Touch.

Labeling information consists of:

1. Company logo and product name.

2. Part number

3. Serial number

4. Date of manufacture (DOM).

5. Name and address of manufacturer.

Figure 9: Product Labels

ADTS542F

PART No: ADTS542F-*****-**-****

SERIAL No: ********

DOM: Mmm-YYYY

DRUCK LIMITED

LE6 0FH, UK

ADTS TOUCH

PART No: ADTSTOUCH

SERIAL No: ********

DOM: Mmm-YYYY

DRUCK LIMITED

LE6 0FH, UK

Dansk–Sikkerheds- og installationsvejledning for ADTS | 13

1. Indledning

Denne vejledning gælder for ADTS542F/552F/553F og 554F, som kaldes ADTS, og indeholder

sikkerheds- og installationsoplysninger om luftdatamåleapparatet i overensstemmelse med

kravene for brug i første linje.

En berøringsskærm (ADTS Touch) bruges til at betjene alle nødvendige funktioner. ADTS Touch

kan placeres på ADTS eller bruges som en håndholdt mobil enhed via et kabel eller trådløs

Bluetooth®-teknologi. Det giver en person mulighed for at gennemføre hele testprogrammet via

fjernadgang, mens personen er bekvemt placeret i flyet. Ekstraudstyret ADTS Touch-ER kan

købes for at få robust trådløs kommunikation i et stort fly. ADTS Touch kan forsynes med strøm,

når enheden er anbragt på ADTS, når enheden er sluttet til ADTS med en kabelforbindelse eller

fra et batteri.

Producenten har udviklet dette udstyr til at være sikkert, når det betjenes ved hjælp af

procedurerne beskrevet i denne manual.

Se Brugermanual K0553 angående kalibreringskrav for ADTS.

Se den aktuelle revision af produktdatabladet angående oplysninger om tilgængelige

producentspecificerede dele.

Service/vedligeholdelse og reparation udføres på Druck-autoriserede servicecentre.

1.1 Mærkninger og symboler

Se listen over Druck-godkendte servicecentre her:

Druck.com

Symbol Beskrivelse

Dette udstyr overholder kravene i alle relevante EU-sikkerhedsdirektiver. Udstyret

bærer CE-mærket.

Dette symbol på udstyret angiver, at brugeren skal læse brugermanualen.

Dette symbol på udstyret indikerer en advarsel, og at brugeren skal se

brugermanualen.

Dette symbol advarer brugeren om fare for elektrisk stød.

Bortskaf ikke dette produkt med husholdningsaffald. Anvend en godkendt

virksomhed, der indsamler og/eller genbruger affald af elektrisk og elektronisk udstyr.

Du kan få yderligere oplysninger ved at kontakte vores kundeserviceafdeling eller

dine lokale myndigheder.

Ordmærket og logoerne til trådløs Bluetooth®-teknologi er registrerede varemærker,

der ejes af Bluetooth SIG, Inc. Alle former for brug fra Druck's side er underlagt licens.

Andre varemærker og varenavne tilhører deres respektive ejere.

14 | Sikkerheds- og installationsvejledning for ADTS–Dansk

1.2 Tilsigtet anvendelse

Test og kalibrering af flytekniske trykinstrumenter, der er placeret indendørs i en hangar eller et

kalibreringslaboratorie eller udendørs (ikke konstant) på en landingsbane. Der er flere

oplysninger i Brugermanual K0553.

Hvis udstyret bruges på en måde, der ikke er angivet i dette dokument eller K0553, kan udstyrets

evne til at give beskyttelse forringes.

1.3 Sikkerhed

Undersøg alt udstyr, der skal bruges, og vær især opmærksom på elektriske ledninger og

konnektorer og pneumatiske rør og konnektorer. BRUG IKKE udstyr, hvis det er konstateret, eller

der er mistanke om, at det er beskadiget eller fejlbehæftet.

1.4 Strømforsyning

1.5 Strømforsyningsforbindelse

Brug ikke en elektrisk strømforsyning uden for de angivne værdier.

Kontroller, at strømforsyningen er slukket, inden strømkablet tilsluttes.

ADTS skal være tilsluttet den korrekte strømforsyning som anført ved siden af strømstikket.

1.6 Sikringer

De to sikringer med høj brydeevne (8) (se Figur 6), der er placeret i holderne og monteret på

frontpanelet, beskytter enheden. Sikringerne er tilsluttet det strømførende og neutrale

forsyningskredsløb og er normeret til: T5AH 250 V.

1.7 Udskiftning af sikring

1. Afbryd den elektriske strømforsyning.

2. Skru sikringsholderdækslet af frontpanelet, og tag sikringen ud.

3. Monter en ny sikring med korrekt størrelse og klassificering i sikringsholderdækslet.

4. Fastgør sikringsholderdækslet på frontpanelet.

ADVARSEL Dette udstyr er ikke normeret til brug i potentielt eksplosive

atmosfærer. Brug af dette udstyr i en potentielt eksplosiv atmosfære kan føre til

alvorlig personskade eller død.

Enfaset 110/230 Vac, 50/60Hz

115 Vac, 400 Hz

200 VA maks. - ADTS542F/ADTS552F

300 VA maks. – ADTS553F/ADTS554F

RISIKO FOR ELEKTRISK STØD Der er risiko for elektrisk stød/dødsfald,

hvis der mangler en beskyttende jordforbindelse. ADTS skal til enhver tid være

tilsluttet den forsyningsbeskyttende jordforbindelse.

Strømforsyningskablet og konnektoren skal være korrekt normeret til

strømforsyningen. Brug kun strømkabler leveret af Druck specielt til ADTS.

Farve i Europa Farve i USA Funktion

Brun Sort Strømførende

Blå Hvid Neutral

Grøn/gul Grøn Beskyttelsesjord

(jordforbindelse)

Dansk–Sikkerheds- og installationsvejledning for ADTS | 15

2. ADTS Touch

ADTS Touch bruges til at betjene alle nødvendige funktioner. ADTS Touch kan placeres på

ADTS eller bruges som en håndholdt mobil enhed via et kabel eller trådløs Bluetooth®-teknologi.

ADTS Touch forsynes med strøm, når:

• Den er placeret (i dock) (1) på en tændt ADTS.

• Der bruges en forbindelsesledning, der er sluttet til en tændt ADTS.

• Den får strøm fra sin egen batteripakke.

• Den får strøm fra en universel strømforsyning

Figur 1: Dockingstik på ADTS Touch

ADTS Touch er udstyret med en tænd/slukknap (2) og USB-stik til tilslutning til en pc eller

lagerenhed (3).

Figur 2: Tænd/sluk-knap og USB-stik på Touch

Et stik (4) giver mulighed for tilslutning mellem basisenheden og ADTS Touch med en

forbindelsesledning på 5 meter eller 18 meter.

Bemærk: Brug kun kabler, der er blevet leveret af eller købt fra Druck.

1

32

16 | Sikkerheds- og installationsvejledning for ADTS–Dansk

Figur 3: Stik til forbindelsesledning til ADTS Touch

ADTS Touch kan indeholde ét litiumionbatteri, som er placeret i batterirummet på ADTS Touch.

2.1 Udskiftning af batteriet

Figur 4: Batterirum i ADTS Touch

Bemærk: Brug kun batterier, der er blevet leveret af eller købt fra Druck.

Sluk ADTS Touch inden udskiftning af batteriet. Hvis ADTS Touch er sluttet til

forbindelsesledningen eller Docking-stikket, skal enheden frakobles, før batteriets dækplade

tages af.

1. Skru de to fingerskruer (5) på batterirummets dækplade af, og fjern dækpladen.

2. Brug den flap, der er fastgjort til batteriet, til at skubbe batteriet ud af batterirummet.

3. Monter et nyt eller genopladet batteri i batterirummet. Sørg for at vende batteriet som vist på

symbolet.

FORSIGTIG Hvis ADTS Touch vippes med batterirummet nedad, efter

dækpladen til batterirummet er fjernet, kan batteriet falde ud af ADTS Touch og

blive beskadiget.

4

55

Dansk–Sikkerheds- og installationsvejledning for ADTS | 17

Bemærk: Batteriet behøver ikke nødvendigvis at være nyt eller genopladet. ADTS Touch vil

fungere sikkert og korrekt med et fladt batteri, når forbindelsesledningen eller dock-

opladningsforsyningen er tilsluttet.

4. Sæt dækpladen på batterirummet igen, og stram de to fingerskruer (5). Pladen skal

monteres korrekt for at opretholde beskyttelsen.

2.2 Pleje og vedligeholdelse af batteri

Batterienheden indeholder et litiumionbatteri, som ikke kræver vedligeholdelse. Hvis ADTS

Touch og/eller batterienheden skal sendes, bedes du kontakte dit lokale servicecenter på forhånd

for at få oplyst kravene til forsendelse. Batteriet skal fjernes fra ADTS Touch under transport.

Udsættelse for ekstreme temperaturer i længere tid kan reducere batteriets levetid væsentligt.

Maksimal levetid opnås ved at undgå længere perioder, hvor batteriet udsættes for temperaturer

uden for området fra -30 °C til +45 °C.

Det anbefalede temperaturområde under opbevaring er 5 °C til 21 °C.

Batteriet kan tages ud. Producenten har følgende sikkerhedsanbefalinger. Brugeren må ikke:

• Kortslutte batteriet.

• Nedsænke batteriet i væske.

• Adskille eller deformere batteriet.

• Udsætte batteriet for eller kaste det på åben ild.

• Udsætte batteriet for kraftige stød eller vibrationer uden for de grænser, der er specificeret

for ADTS.

• Bruge et batteri, der ser ud til at have været misligholdt.

• Oplade batteriet med en ikke-specificeret oplader eller en specificeret oplader, der er blevet

ændret. Det kan nedbryde batteriet eller få det til at svulme op eller revne.

• Bruge et batteri i et apparat eller til et formål, det ikke er beregnet til.

Batterienheden er forseglet permanent. Elektrolytlækage forventes ikke. Hvis der observeres

elektrolytlækage fra batteriet, skal brugen af batteriet straks ophøre, og kontakt med elektrolytten

skal undgås. Hvis huden eller tøjet kommer i kontakt med elektrolytten, vaskes straks med sæbe

og vand. Hvis elektrolytten kommer i kontakt med øjnene, skal øjnene vaskes grundigt med vand,

og der skal straks søges lægehjælp.

ADTS5xxF, ADTS Touch og ADTS Touch-ER indeholder et litiumionmøntcellebatteri. Dette

møntcellebatteri kan ikke udskiftes af brugeren. Installation og udskiftning må kun udføres af

uddannet personale.

Bortskaf altid batterier sikkert og i overensstemmelse med lokale anvisninger.

2.3 Opladning af batteri

Batteriet i ADTS Touch kan oplades på følgende måder:

• Ved at placere ADTS Touch på en ADTS med strømforsyning.

• Ved at slutte stikket på ADTS Touch (4) (se Figur 3) til ADTS ved hjælp af

forbindelsesledningen.

• Ved hjælp af AATOUCH-5-bordladeren (ekstraudstyr). Batteriet skal fjernes fra ADTS

Touch, når det oplades af AATOUCH-5-bordladeren.

18 | Sikkerheds- og installationsvejledning for ADTS–Dansk

• Med en universel strømforsyning, der er sluttet til ADTS Touch via en adapter:

Figur 5: Universal strømforsyning og adapter

Den universelle strømforsyning og bordopladeren til ADTS Touch er kun beregnet til indendørs

brug.

Sayfa yükleniyor ...

Druck 542F Yükleme Rehberi

Druck 542F Yükleme Rehberi

Diğer dillerde

Diğer Belgeler