LG 32LW341H(EU) Kullanım kılavuzu

Please read this manual carefully before operating your

set and retain it for future reference.

Safety and Reference

OWNER’S MANUAL

www.lg.com

LED TV*

* LG LED TV applies LCD screen with LED backlights.

2

ENGLISH

Safety instructions

Please read these safety precautions carefully

before using the product.

WARNING

Do not place the TV and/or remote control in the following

environments:

• A location exposed to direct sunlight

• An area with high humidity such as a bathroom

• Near any heat source such as stoves and other devices that produce

heat

• Near kitchen counters or humidiers where they can easily be

exposed to steam or oil

• An area exposed to rain or wind

• Near containers of water such as vases

Otherwise, this may result in re, electric shock, malfunction or product

deformation.

Do not place the product where it might be exposed to dust. This may

cause a re hazard.

Mains Plug is the TV connecting/disconnecting device to AC mains

electric supply. This plug must remain readily attached and operable

when TV is in use.

Do not touch the power plug with wet hands. Additionally, if the cord

pin is wet or covered with dust, dry the power plug completely or wipe

dust o. You may be electrocuted due to excess moisture.

Make sure to connect Mains cable to compliant AC mains socket with

Grounded earth pin. (Except for devices which are not grounded on

earth.) Otherwise possibility you may be electrocuted or injured.

Insert power cable plug completely into wall socket otherwise if not

secured completely into socket, re ignition may break out.

Ensure the power cord does not come into contact with hot objects such

as a heater. This may cause a re or an electric shock hazard.

Do not place a heavy object, or the product itself, on power cables.

Otherwise, this may result in re or electric shock.

Bend antenna cable between inside and outside building to prevent

rain from owing in. This may cause water damaged inside the Product

and could give an electric shock.

When mounting TV onto wall make sure to neatly install and isolate

cabling from rear of TV as to not create possibility of electric shock /

re hazard.

Do not plug too many electrical devices into a single multiple electrical

outlet. Otherwise, this may result in re due to over-heating.

ENGLISH

3

Do not drop the product or let it fall over when connecting external

devices. Otherwise, this may result in injury or damage to the product.

Desiccant

Keep the anti-moisture packing material or vinyl packing out of the

reach of children. Anti-moisture material is harmful if swallowed. If

swallowed by mistake, force the patient to vomit and visit the nearest

hospital. Additionally, vinyl packing can cause suocation. Keep it out of

the reach of children.

Do not let your children climb or cling onto the TV.

Otherwise, the TV may fall over, which may cause serious injury.

Dispose of used batteries carefully to ensure that a small child does not

consume them. Please seek Doctor- Medical Attention immediately if

child consumes batteries.

Do not insert any metal objects/conductors (like a metal chopstick/

cutlery/screwdriver) between power cable plug and input Wall Socket

while it is connected to the input terminal on the wall. Additionally,

do not touch the power cable right after plugging into the wall input

terminal. You may be electrocuted. (Depending on model)

Do not put or store inammable substances near the product. There is a

danger of combustion/explosion or re due to careless handling of the

inammable substances.

Do not drop metallic objects such as coins, hair pins, chopsticks or wire

into the product, or inammable objects such as paper and matches.

Children must pay particular attention. Electrical shock, re or injury

can occur. If a foreign object is dropped into the product, unplug the

power cord and contact the service centre.

Do not spray water on the product or scrub with an inammable

substance (thinner or benzene). Fire or electric shock accident can occur.

Do not allow any impact, shock or any objects to fall into the unit,

and do not drop anything onto the screen. You may be injured or the

product can be damaged.

Never touch this product or antenna during a thunder or lighting storm.

You may be electrocuted.

Never touch the wall outlet when there is leakage of gas, open the

windows and ventilate. It may cause a re or a burn by a spark.

Do not disassemble, repair or modify the product at your own

discretion. Fire or electric shock accident can occur.

Contact the service centre for check, calibration or repair.

4

ENGLISH

If any of the following occur, unplug the product immediately and

contact your local service centre.

• The product has been impacted by shock

• The product has been damaged

• Foreign objects have entered the product

• The product produced smoke or a strange smell

This may result in re or electric shock.

Unplug the TV from AC mains wall socket if you do not intend to use the

TV for a long period of time. Accumulated dust can cause re hazard

and insulation deterioration can cause electric leakage/shock/re.

Apparatus shall not be exposed to dripping or splashing and no objects

lled with liquids, such as vases, shall be placed on the apparatus.

Do not install this product on a wall if it could be exposed to oil or oil

mist. This may damage the product and cause it to fall.

If water enters or comes into contact with TV, AC adapter or power

cord please disconnect the power cord and contact service centre

immediately. Otherwise, this may result in electric shock or re.

Only use an authorized AC adapter and power cord approved by

LG Electronics. Otherwise, this may result in re, electric shock,

malfunction or product deformation.

Never Disassemble the AC adapter or power cord. This may result in re

or electric shock.

Be careful in handling the adapter to prevent any external shocks to it.

An external shock may cause damage to the adapter.

Make sure the power cord is connected securely to the power plug on

the TV. (Depending on model)

CAUTION

Install the product where no radio wave occurs.

There should be enough distance between an outside antenna and

power lines to keep the former from touching the latter even when the

antenna falls. This may cause an electric shock.

Do not install the product on places such as unstable shelves or inclined

surfaces. Also avoid places where there is vibration or where the

product cannot be fully supported. Otherwise, the product may fall or

ip over, which may cause injury or damage to the product.

If you install the TV on a stand, you need to take actions to prevent the

product from overturning. Otherwise, the product may fall over, which

may cause injury.

If you intend to mount the product to a wall, attach VESA standard

mounting interface (optional parts) to the back of the product. When

you install the set to use the wall mounting bracket (optional parts), x

it carefully so as not to drop.

ENGLISH

5

Only use the attachments / accessories specied by the manufacturer.

When installing the antenna, consult with a qualied service

technician. If not installed by a qualied technician, this may create a

re hazard or an electric shock hazard.

We recommend that you maintain a distance of at least 2 to 7 times

the diagonal screen size when watching TV. If you watch TV for a long

period of time, this may cause blurred vision.

Only use the specied type of battery. This could cause damage to the

remote control.

Do not mix new batteries with old batteries. This may cause the

batteries to overheat and leak.

Batteries should not be exposed to excessive heat. For example, keep

away from direct Sunlight , open replace and electric heaters.

Do not place non-rechargeable batteries in charging device.

Make sure there are no objects between the remote control and its

sensor.

Signal from Remote Control can be interrupted due to external/internal

lighting eg Sunlight, uorescent lighting. If this occurs turn o lighting

or darken viewing area.

When connecting external devices such as video game consoles, make

sure the connecting cables are long enough. Otherwise, the product

may fall over, which may cause injury or damage the product.

Do not turn the product On/O by plugging-in or unplugging the power

plug to the wall outlet. (Do not use the power plug for switch.) It may

cause mechanical failure or could give an electric shock.

Please follow the installation instructions below to prevent the product

from overheating.

• The distance between the product and the wall should be more

than 10cm.

• Do not install the product in a place with no ventilation (e.g., on a

bookshelf or in a cupboard).

• Do not install the product on a carpet or cushion.

• Make sure the air vent is not blocked by a tablecloth or curtain.

Otherwise, this may result in re.

Take care not to touch the ventilation openings when watching the TV

for long periods as the ventilation openings may become hot. This does

not aect the operation or performance of the product.

Periodically examine the cord of your appliance, and if its appearance

indicates damage or deterioration, unplug it, discontinue use of the

appliance, and have the cord replaced with an exact replacement part

by an authorized servicer.

Prevent dust collecting on the power plug pins or outlet. This may cause

a re hazard.

6

ENGLISH

Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon. Pay

particular attention to plugs, wall outlets, and the point where the cord

exits the appliance.

Do not press strongly upon the panel with a hand or sharp object such

as nail, pencil or pen, or make a scratch on it, as it may causedamage

to screen.

Avoid touching the screen or holding your nger(s) against it for long

periods of time. Doing so may produce some temporary or permanent

distortion/damage to screen.

When cleaning the product and its components, unplug the power

rst and wipe it with a soft cloth. Applying excessive force may cause

scratches or discolouration. Do not spray with water or wipe with a wet

cloth. Never use glass cleaner, car or industrial shiner, abrasives or wax,

benzene, alcohol etc., which can damage the product and its panel.

Otherwise, this may result in re, electric shock or product damage

(deformation, corrosion or breakage).

As long as this unit is connected to the AC wall outlet, it is not

disconnected from the AC power source even if you turn o this unit

by SWITCH.

When unplugging the cable, grab the plug and unplug it, by pulling at

the plug.

Don’t pull at the cord to unplug the power cord from the power board,

as this could be hazardous.

When moving the product, make sure you turn the power o rst. Then,

unplug the power cables, antenna cables and all connecting cables.

The TV set or power cord may be damaged, which may create a re

hazard or cause electric shock.

When moving or unpacking the product, work in pairs because the

product is heavy. Otherwise, this may result in injury.

Refer all servicing to qualied service personnel. Servicing is required

when the apparatus has been damaged in any way, such as power

supply cord or plug is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been exposed to rain or

moisture, does not operate normally, or has been dropped.

If the product feels cold to the touch, there may be a small “icker”

when it is turned on. This is normal, there is nothing wrong with

product.

This panel is an advanced product that contains millions of pixels.

You may see tiny black dots and/or brightly coloured dots (red, blue

or green) at a size of 1ppm on the panel. This does not indicate a

malfunction and does not aect the performance and reliability of the

product.

This phenomenon also occurs in third-party products and is not subject

to exchange or refund.

ENGLISH

7

You may nd dierent brightness and color of the panel depending on

your viewing position(left/right/top/down).

This phenomenon occurs due to the characteristic of the panel. It is not

related with the product performance, and it is not malfunction.

Displaying a still image for a prolonged period of time may cause image

sticking. Avoid displaying a xed image on the TV screen for a long

period of time.

Generated Sound

“Cracking” noise: A cracking noise that occurs when watching or turning

o the TV is generated by plastic thermal contraction due to tempera-

ture and humidity. This noise is common for products where thermal

deformation is required. Electrical circuit humming/panel buzzing:

A low level noise is generated from a high-speed switching circuit,

which supplies a large amount of current to operate a product. It varies

depending on the product.

This generated sound does not aect the performance and reliability

of the product.

Do not use high voltage electrical goods near the TV (e.g. electric

mosquito-swatter). This may result in product malfunction.

Preparing

NOTE

• Image shown may dier from your TV.

• Your TV’s OSD (On Screen Display) may dier slightly from that

shown in this manual.

• The available menus and options may dier from the input source

or product model that you are using.

• New features may be added to this TV in the future.

• The items supplied with your product may vary depending on the

model.

• Product specications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and USB devices should

have bezels less than 10 mm thick and 18 mm width. Use an

extension cable that supports USB 2.0 if the USB cable or USB

memory stick does not t into your TV’s USB port.

A

B

A

B

*A

<

=

10 mm

*B

<

=

18 mm

• Use a certied cable with the HDMI logo attached.

• If you do not use a certied HDMI cable, the screen may not display

or a connection error may occur. (Recommended HDMI Cable Types)

- High-Speed HDMI

®

/

TM

cable (3 m or less)

- High-Speed HDMI

®

/

TM

cable with Ethernet (3 m or less)

• Antenna isolator installation guide (Depending on model)

- Use this to install TV in a place where there is a voltage

dierence between TV Set and GND of antenna signal.

» If there is a voltage dierence between TV Set and GND of

antenna signal, the antenna contact might be heated and

excessive heat might cause an accident.

- You can improve the safety when watching TV by eciently

removing power voltage from TV antenna. It is recommended

to mount the isolator to the wall. If it cannot be mounted to

the wall, mount it on the TV. Avoid disconnecting the antenna

Isolator after installation.

- Before starting, be sure that the TV antenna is connected.

ANTENNA/

CABLE IN

Cable /

Antenna

Wall

Isolator

or

1. Connect to TV.

2. Connect to Set-Top box.

- Connect one end of the isolator to cable/antenna jack and the

other to TV set or set-top box.

“Equipment connected to the protective earthing of the building

installation through the mains connection or through other

equipment with a connection to protective earthing - and to

a cable distribution system using coaxial cable, may in some

circumstances create a re hazard. Connection to a cable

distribution system has therefore to be provided through a

device providing electrical isolation below a certain frequency

range (galvanic isolator, see EN 60728-11)”

- When applying the RF Isolator, a slight loss of signal sensitivity

can occur.

8

ENGLISH

CAUTION

• Do not use any unapproved items to ensure the safety and product

life span.

• Any damage or injuries caused by using unapproved items are not

covered by the warranty.

• Some models have a thin lm attached on to the screen and this

must not be removed.

• When attaching the stand to the TV set, place the screen facing

down on a cushioned table or at surface to protect the screen

from scratches.

• Make sure that the screws are fastened completely. (If they are

not fastened securely enough, the TV may tilt forward after being

installed.) Do not use too much force and over tighten the screws;

otherwise screw may be damaged and not tighten correctly.

Separate purchase

Separate purchase items can be changed or modied for quality

improvement without any notication. Contact your dealer to buy

these items. These devices only work with certain models. The model

name or design may be changed depending on the upgrade of product

functions, manufacturer’s circumstances or policies.

(Depending on model)

LED Clock

LEC-003

AN-WF500

Wi-Fi/Bluetooth Dongle

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched

or damaged and for safe transportation regardless of its type and size.

• It is recommended to move the TV in the box or packing material

that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and

all cables.

• When holding the TV, the screen should face away from you to

avoid damage.

• Hold the top and bottom of the TV frame rmly. Make sure not to

hold the transparent part, speaker, or speaker grill area.

• When transporting a large TV, there should be at least 2 people.

• When transporting the TV by hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV to jolts or

excessive vibration.

• When transporting the TV, keep the TV upright, never turn the TV

on its side or tilt towards the left or right.

• Do not apply excessive pressure to cause exing / bending of frame

chassis as it may damage screen.

• When handling the TV, be careful not to damage the protruding

buttons.

CAUTION

• Avoid touching the screen at all times, as this may result in damage

to the screen.

• Do not move the TV by holding the cable holders, as the cable

holders may break, and injuries and damage to the TV may occur.

ENGLISH

9

Using the button

(Depending on model)

You can simply operate the TV functions, pressing or moving the button.

NOTE

• LW30 series does not have a Joystick functions but has only a

power On/O button.

Dome button

or

Joystick button

Basic functions

Power On (Press)

Power O (Press and hold)

1

Volume Control

Programmes Control

1 If the Menu button is on the screen, pressing and holding the button

will let you exit the Menu.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust

the Menu items pressing or moving the buttons.

Turns the power o.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

Accesses the settings menu.

Mounting on a table

1 Lift and tilt the TV into its upright position on a table.

• Leave a 10 cm (minimum) space from the wall for proper

ventilation.

10 cm

2 Connect the power cord to a wall outlet.

CAUTION

• Do not place the TV near or on sources of heat, as this may result in

re or other damage.

10

ENGLISH

Attaching the TV to a desk

(This feature is not available for all models.)

The TV should be attached to a desk so it cannot be pulled in a forward/

backward direction, potentially causing injury or damaging the product.

4-Screws

(Not supplied with TV)

A type)

Stand

Desk

NOTE

• Screw : M5 x L (*L: Table depth + 8~10 mm)

ex) Table depth: 15 mm, Screw : M5 x L25

2-Screws for Stand Fixing,

2-Washers for Stand Fixing,

2-Nuts for Stand Fixing

(Supplied with TV)

B type)

Stand

Desk

Using the kensington security

system

(This feature is not available for all models.)

• Image shown may dier from your TV.

The Kensington security system connector is located at the rear of the

TV. For more information of installation and using, refer to the manual

provided with the Kensington security system or visit http://www.

kensington.com. Connect the Kensington security system cable between

the TV and a table.

Securing the TV to a wall

(This feature is not available for all models.)

1 Insert and tighten the eye-bolts, or TV brackets and bolts on the back

of the TV.

• If there are bolts inserted at the eye-bolts position, remove the

bolts rst.

2 Mount the wall brackets with the bolts to the wall.

Match the location of the wall bracket and the eye-bolts on the rear

of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope.

Make sure to keep the rope horizontal with the at surface.

CAUTION

• Make sure that children do not climb on or hang on the TV.

NOTE

• Use a platform or cabinet that is strong and large enough to

support the TV securely.

• Brackets, bolts and ropes are not provided. You can obtain

additional accessories from your local dealer.

ENGLISH

11

Adjusting the angle of the TV to suit

view

(This feature is not available for all models.)

Swivel 20 degrees to the left or right and adjust the angle of the TV to

suit your view.

20˚20˚

CAUTION

• When adjusting the angle of the product, watch out for your

ngers.

- Personal injury may occur if hands or ngers are pinched. If the

product is tilted too much, it may fall, causing damage or injury.

Mounting on a wall

Attach an optional wall mount bracket at the rear of the TV carefully

and install the wall mount bracket on a solid wall perpendicular to

the oor. When you attach the TV to other building materials, please

contact qualied personnel. LG recommends that wall mounting be

performed by a qualied professional installer. We recommend the use

of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with

cables connected. When you do not use LG’s wall mount bracket, please

use a wall mount bracket where the device is adequately secured to the

wall with enough space to allow connectivity to external devices. It is

advised to connect all the cables before installing xed wall mounts.

10 cm

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

Separate purchase(Wall Mounting Bracket)

Model

32LW30**

43LW31**

32/43LW34**

32/43LW54**

49LW31**

49/55LW34*

49/55LW54**

VESA (A x B) (mm) 200 x 200 300 x 300

Standard screw M6 M6

Number of screws 4 4

Wall mount

bracket

LSW240B

MSW240

LSW350B

MSW240

Model 24LW34** 28LW34**

VESA (A x B) (mm) 75 x 75 100 x 100

Standard screw M4 X L10 M4 X L10

Number of screws 4 4

Wall mount

bracket

LSW140B LSW140B

A

B

CAUTION

• Remove the stand before installing the TV on a wall mount by

performing the stand attachment in reverse.

NOTE

• When installing the wall mounting bracket, use the adhesive

label provided. The adhesive label will protect the opening from

accumulating dust and dirt. (Only when the item of the following

form is provided)

Provided item

Adhesive label

12

ENGLISH

• When installing the wall mounting bracket, it is recommended to

cover the stand hole using tape, in order to prevent the inux of

dust and insects. (Depending on model)

Stand hole

• Screw length from outer surface of back cover should be under

8 mm. (Only LW341C)

Wall mount Pad

Back Cover

Standard screw

: M4 x L10

Wall mount Pad

Back Cover

Max. 8 mm

How to use Dual Lock™

(Only when the item of the following form is provided)

(Except for 32LW30**)

(This feature is not available for all models.)

Fix the set-top box to the TV and use it when you want to.

1 After removing the protection paper from the Dual Lock

TM

, stick it to

the TV and the set-top box as shown.

Dual Lock™

2 Attach the set-top box to the TV by pressing the Velcro strips

together.

NOTE

• Please make sure no foreign substances exist on the surface of the

product, and then rmly attach the Dual Lock™.

• Before attaching the set-top box to the TV set, let the attached

Dual Lock™ dry for at least three days.

ENGLISH

13

Connections (notications)

Connect various external devices to the TV and switch input modes to

select an external device. For more information of external device’s

connection, refer to the manual provided with each device.

Available external devices are: HD receivers, DVD players, VCRs, audio

systems, USB storage devices, PC, gaming devices, and other external

devices.

NOTE

• The external device connection may dier from the model.

• Connect external devices to the TV regardless of the order of the

TV port.

• If you record a TV program on a DVD recorder or VCR, make sure to

connect the TV signal input cable to the TV through a DVD recorder

or VCR. For more information of recording, refer to the manual

provided with the connected device.

• Refer to the external equipment’s manual for operating

instructions.

• If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

• In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the PICTURE

menu until the picture is clear.

• In PC mode, some resolution settings may not work properly

depending on the graphics card.

Antenna connection

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

• Use a signal splitter to use more than 2 TVs.

• If the image quality is poor, install a signal amplier properly to

improve the image quality.

• If the image quality is poor with an antenna connected, try to

realign the antenna in the correct direction.

• An antenna cable and converter are not supplied.

• Supported DTV Audio: MPEG, Dolby Digital, Dolby Digital Plus,

HE-AAC

Satellite dish connection

(Only satellite models)

Connect the TV to a satellite dish to a satellite socket with a satellite RF

cable (75 Ω).

Adapter connection

(Depending on model)

CAUTION

• Please be sure to connect the TV to the AC-DC power adapter

before connecting the TV’s power plug to a wall power outlet.

CI module connection

(Depending on model)

View the encrypted (pay) services in digital TV mode.

• Check if the CI module is inserted into the PCMCIA card slot in the

right direction. If the module is not inserted properly, this can

cause damage to the TV and the PCMCIA card slot.

• If the TV does not display any video and audio when CI+ CAM is

connected, please contact to the Terrestrial/Cable/Satellite Service

Operator.

Speaker Output Setup

(Depending on model)

EXTERNAL

SPEAKER OUT

VOLUME

CONTROL

+

-

STEREO 8

UP

DOWN

Control port for Speaker out

RIGHT

LEFT

GND

: Depending on model

or

14

ENGLISH

NOTE

• Use only with the 3 Pole 3.5 mm Stereo Jack.

• Do not connect your headphones or earphones to the port for

connecting an external speaker.

Method of Volume control port

(Depending on model)

• Cable Spec.

GND / Up / Down

Each Up / Down pin

is pulled to 3.3 V with

CPU GPIO.

CPU detects transition

from 3.3 V to GND level

for volume control.

Network setup

Wired network connection

(Depending on model)

This TV can be connected to a Pro:Centric server via the LAN port. After

making the physical connection, the TV needs to be set up for network

communication. Connect the LAN port of the Modem or Router from

Pro:Centric server to the LAN port on the TV.

(MHEG / SERVICE)

LAN

Pro:Centric Server

Broadband Modem

Pro:Centric Server

Router

or

CAUTION

• Do not connect a modular phone cable to the LAN port.

• Since there are various connection methods, please follow the

specications of your telecommunication carrier or internet service

provider.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

Some separate cable is not provided.

ENGLISH

15

Remote control

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

To replace batteries, open the battery cover, replace batteries (1.5

V AAA) matching the

and ends to the label inside the

compartment, and close the battery cover. To remove the batteries,

perform the installation actions in reverse.

Make sure to point the remote control toward the remote control sensor

on the TV.

(Depending on model)

A

B

1

1 1

2

A

(POWER) Turns the TV on or o.

Selects Radio, TV and DTV programme.

Recalls your preferred subtitle in digital mode.

1

By pressing the AD button, audio descriptions function will be

enabled. (Depending on model)

1

Selects an AV mode. (Depending on model)

1

, Resizes an image. (Depending on model)

1

(INPUT) , Changes the input source. (Depending

on model)

Number buttons Enters numbers.

Accesses the saved programme list.

Returns to the previously viewed programme.

B

Adjusts the volume level.

Accesses your favourite programme list.

Shows programme guide.

2

(MUTE) , Mutes all sounds. (Depending on model)

Scrolls through the saved programmes.

Moves to the previous or next screen.

C

D

3

4

C

Teletext buttons ( ) These buttons are used for

teletext.

3

(HOME) Accesses the Home menu. (Depending on model)

3

Views the information of the current programme and

screen. (Depending on model)

3

(Settings) , Accesses the Settings menu.

(Depending on model)

Accesses the Quick menus.

Navigation buttons (up/down/left/right) Scrolls through menus

or options.

Selects menus or options and conrms your input.

3

, Returns to the previous level. (Depending on

model)

Clears on-screen displays and returns to TV viewing.

D

4

Views the information of the current programme and

screen. (Depending on model)

4

Accesses the AV devices connected with the HDMI

cable through HDMI-CEC. Opens the SIMPLINK menu. (Depending

on model)

4

Starts to record and displays record menu. (Depending

on model)

4

By pressing the AD button, audio descriptions function will be

enabled. (Depending on model)

Control buttons (

) Controls media contents.

Coloured buttons These access special functions in some menus.

(

: Red, : Green, : Yellow, : Blue)

16

ENGLISH

(Depending on model)

A

B

A

(POWER) Turns the TV on or o.

Adjusts the brightness of the screen to reduce

energy consumption.

Selects an AV mode.

Changes the input source.

Selects Radio, TV and DTV programme.

Number buttons Enters numbers.

Accesses the saved programme list.

Returns to the previously viewed programme.

B

Adjusts the volume level.

Accesses your favourite programme list.

Resizes an image.

Mutes all sounds.

Scrolls through the saved programmes.

PAGE Moves to the previous or next screen.

C

D

C

Shows programme guide.

Displays and removes hotel interactive menu.

Views the information of the current programme and

screen.

Navigation buttons (up/down/left/right) Scrolls through

menus or options.

Selects menus or options and conrms your input.

Accesses the main menus.

(BACK) Returns to the previous level.

Clears on-screen displays and return to TV viewing.

Coloured buttons These access special functions in some menus.

(

: Red, : Green, : Yellow, : Blue)

D

Teletext buttons ( ) These buttons are used for

teletext.

Recalls your preferred subtitle in digital mode.

Control buttons (

) Controls media contents.

Accesses the AV devices connected with the HDMI

cable through HDMI-CEC. Opens the SIMPLINK menu.

Accesses the Quick menus.

By pressing the AD button, audio descriptions function will be

enabled.

Sets the alarm function. (Depending on model)

ENGLISH

17

Licenses

Supported licenses may dier by model. For more information about

licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories.

Dolby and the double-D symbol are trademarks of Dolby

Laboratories.

The terms HDMI and HDMI High-Denition Multimedia interface,

and the HDMI logo are trademarks or registered trademarks of HDMI

Licensing LLC in the United States and other countries.

This DivX Certied® device has passed rigorous testing to ensure it

plays DivX® video.

To play purchased DivX movies, rst register your device at vod.divx.

com. Find your registration code in the DivX VOD section of your

device setup menu.

DivX Certied® to play DivX® video up to HD 1080p, including

premium content.

DivX®, DivX Certied® and associated logos are trademarks of DivX,

LLC and are used under license.

Covered by DivX Patents 7,295,673; 7,515,710; RE45,052; and others

available at [www.divx.com/patents].

Open source software

notice information

To obtain the source code under GPL, LGPL, MPL and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om. This oer is valid for three (3) years from the date

on which you purchased the product.

Troubleshooting

The software version can be updated for improvement in performance.

Customer needs to ensure the compatibility of customer’s equipment

with LGE software. If needed, please consult with LGE and upload

revised software version according to the guidance provided by LGE.

Cannot control the TV with the remote control.

• Check the remote control sensor on the product and try again.

• Check if there is any obstacle between the product and the remote

control.

• Check if the batteries are still working and properly installed (

to , to ).

No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other

products.

The TV turns o suddenly.

• Check the power control settings. The power supply may be

interrupted.

• Check if the Automatic Standby (Depending on model) / Sleep

Timer / Off Time is activated in the TIME settings. (Depending

on model)

• Check if the Auto Power Off (Depending on model) / Sleep

Timer / Timer Power Off is activated in the Timers settings.

(Depending on model)

• If there is no signal while the TV is on, the TV will turn o

automatically after 15 minutes of inactivity.

When connecting to the PC (RGB/HDMI/DVI), ‘No signal’ or ‘Invalid

Format’ is displayed.

• Turn the TV o/on using the remote control.

• Reconnect the RGB/HDMI cable.

• Restart the PC with the TV on.

18

ENGLISH

Software download information

• Use this information for LW540S series.

You can download the SuperSign Software and manual from LG Electronics website.

https://www.lgecommercial.com/digital-signage/support/download/supersign

Software : SuperSign W_Lite_Server_vX.X.X_Setup.zip

SuperSign C_vX.X.X_Setup.zip

SuperSign W_Editor_vX.X.X_Setup.zip

SuperSign W_Player_vX.X.X_Setup.zip

Manual : SuperSign W_Lite_Server_vX.X.X_Manual.zip

SuperSign C_vX.X.X_Manual.zip

SuperSign W_Editor_vX.X.X_Manual.zip

SuperSign W_Player_vX.X.X_Manual.zip

Specications

CI Module (W x H x D) 100.0 mm x 55.0 mm x 5.0 mm

Environment condition

Operating Temperature 0 °C to 40 °C

Operating Humidity Less than 80 %

Storage Temperature -20 °C to 60 °C

Storage Humidity Less than 85 %

AC/DC Adapter

32LW30**

Manufacturer : Lien Chang

Model : LCAP16B-E, LCAP25B

Manufacturer : Honor

Model : ADS-45FSN-19 19040GPG,

ADS-45SN-19-2 19040G

Input : AC 100 - 240 V ~ 50/60 Hz

Output : DC 19 V

2.1 A

ENGLISH

19

(Depending on country)

Digital TV Analogue TV

Satellite Terrestrial Cable Terrestrial / Cable

Television system DVB-S/S2*

DVB-T

DVB-T2*

DVB-C

PAL/SECAM B/G, D/K, I,

SECAM L

Channel coverage

(Band)

950 ~ 2150 Mhz

VHF III : 174 ~ 230 Mhz

UHF IV : 470 ~ 606 Mhz

UHF V : 606 ~ 862 Mhz

S Band II : 230 ~ 300 Mhz

S Band III : 300 ~ 470 Mhz

46 ~ 862 Mhz 46 ~ 862 Mhz

Maximum number of

storable programmes

6,000

1,500 (Only LW341H, LW54**)

2,000 (Only LW30**, LW31**, LW340*, LW341C)

External antenna impedance 75 Ω

* Only DVB-T2/C/S2 support models.

20

ENGLISH

HDMI/DVI-DTV supported mode

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

640 x 480

31.46

31.50

59.94

60.00

720 x 480

31.469

31.50

59.94

60.00

720 x 576 31.250 50.00

1280 x 720

37.50

45

44.96

50.00

60.00

59.94

1920 x 1080

28.125

33.75

33.72

56.250

67.50

67.432

27.00

26.973

33.75

33.716

50.00

60.00

59.94

50.00

60.00

59.94

24.00

23.976

30.00

29.976

RGB-PC supported mode

(Only LW31**, LW340*, LW341C, LW341H, LW540*)

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

640 x 350 31.468 70.09

720 x 400 31.469 70.08

640 x 480 31.469 59.94

800 x 600 37.879 60.31

1024 x 768 48.363 60.00

1152 x 864 54.348 60.053

1360 x 768 47.712 60.015

1280 x 1024

(Only FHD)

63.981 60.020

1920 x 1080

(Only FHD)

66.587

67.50

59.934

60.00

1

: Only LW31**, LW340*, LW341H, LW540*

HDMI/DVI-PC supported mode

(Use HDMI IN 1 for PC mode)

Resolution

Horizontal

Frequency

(kHz)

Vertical

Frequency

(Hz)

640 x 350 31.468 70.09

720 x 400 31.469 70.08

640 x 480 31.469 59.94

800 x 600 37.879 60.31

1024 x 768 48.363 60.00

1152 x 864 54.348 60.053

1360 x 768 47.712 60.015

1280 x 1024

(Only FHD)

63.981 60.020

1920 x 1080

(Only FHD)

67.50 60.00

1

: Only LW31**, LW340*, LW341H, LW54**

Component port connecting

information

Component ports on the TV Y P

B

P

R

Video output ports on

DVD player

Y P

B

P

R

Y B-Y R-Y

Y Cb Cr

Y Pb Pr

Signal Component

480i / 576i O

480p / 576p O

720p / 1080i O

1080p

O

(Only 50 Hz / 60 Hz)

Sayfa yükleniyor ...

LG 32LW341H(EU) Kullanım kılavuzu

LG 32LW341H(EU) Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler