Yamaha CRW3200IX Kullanım kılavuzu

Marka: Yamaha

Model: CRW3200IX

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

CRW3200IX Series

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation, USA.

Address: 6660 Orangethorpe Avenue

Buena Park, CA 90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: CD Recordable/Rewritable Drive

Model Name: CRW3200IX

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that

may cause undesired operation.

See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void

your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class

“B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product

in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses

radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause

interference harmful to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that

interference will not occur in all installations. If this product is found to be the source of interference, which can be determined

by turning the product “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change

the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this

type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corporation, USA.

6660 Orangethorpe Avenue, Buena Park, CA 90620 U.S.A.

CAUTION - VISIBLE AND / OR INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA

DEL ÄR ÖPPNAD. STRÅLEN ÄR FARLIG.

VARO ! AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA / TAI

NÄKYMÄTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING - SYNLIG OCH / ELLER OSYNLIG LASERSTRÅLNING NÄR DENNA DEL

ÄR ÖPPNAD. BETRAKTA EJ STRÅLEN.

VORSICHT ! SICHTBARE UND / ODER UNSICHTBARE LASERSTRAHLUNG

WENN ABDECKUNG GEÖFFNET. NICHT DEM STRAHL AUSSETZEN.

ATTENTION - RADIATION VISIBLE ET / OU INVISIBLE LORSQUE L’APPAREIL

EST OUVERT. EVITEZ TOUTE EXPOSITION AU FAISCEAU.

COMPLIES WITH 21 CFR CHAPTER 1, SUBCHAPTER J.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

KLASS 1 LASER APPARAT

PRODUIT LASER DE CLASSE 1

DANGER - VISIBLE AND / OR INVISIBLE LASER

RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE

TO BEAM.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

Laser Product Class: Class 1

Laser Diode Properties

Wavelength: 780 – 787 nm

Pulse Durations and Max. Output

at the lens of the Laser Pickup Unit

Read Mode: 0.85 mW (Continuous)

Write Mode: Max. 48 mW

(for 212 ns, Min. Cycle 57.9 ns)

ACHTUNG

Halten Sie sich beim Bedienen und Einstellen der

Bedienungselemente sowie bei der Bedienungsabfolge

an die Anleitung, da sonst gefährliche Strahlen austreten

können.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereuses.

PRECAUCION

El usar los controles o ajustar o realizar procedimientos

diferentes a los especificados aquí resultará en

peligrosas exposiciones a la radiación.

VARO! AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING! OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN. STRÅLEN ÄR FARLIG.

Laserprodukt-Klasse: Klasse 1

Eigenschaften der Laserdiode

Wellenlänge: 780 – 787 nm

Impulsdauer und max. Ausgang an der Linse der

Laser-Abtasteinheit

Lesemodus: 0,85 mW (kontinuierlich)

Schreibmodus: Max. 48 mW

(für 212 ns, Zyklusmin. 57,9 ns)

Classe du produit laser: Classe 1

Caractéristiques de la diode laser

Longueur d’onde: 780 – 787 nm

Durée des impulsions et sortie maximum depuis

la lentille du bloc capteur optique

Mode de lecture: 0,85 mW (continue)

Mode de gravure: max. 48 mW

(pour 212 ns, cycle min. 57,9 ns)

Clase de producto láser: Clase 1

Propiedades del diodo láser

Longitud de onda: 780 – 787 nm

Duración del pulso y potencia de salida máxima

en el objetivo de la unidad captora láser

Modo de lectura: 0,85 mW (continua)

Modo de escritura: máx. 48 mW

(para 212 ns, ciclo mínimo 57,9 ns)

OWNER’S MANUAL

English

SAFETY PRECAUTIONS

PLEASE READ THE FOLLOWING WARNINGS AND CAUTIONS CAREFULLY TO

PREVENT PERSONAL INJURY AND DAMAGE TO THE DEVICE.

These precautions explain how to use the device properly and safely, thereby preventing

injury to yourself and others. This section has been sub-divided into a WARNING section

and a CAUTION section, according to the likelihood and nature of any potential injuries or

damage inflicted. They relate to your personal safety, and also help you prevent the risk

of damage to the device. Please read these sections carefully prior to proceeding.

WARNING

Always follow these basic precautions to avoid short-circuit, damage, fire, or other

hazards, and to avoid serious injury or fatal accident from electrical shock.

●

Do not attempt to open or disassemble the device to avoid the risk of electrical shock,

fire, or malfunction.

●

Do not look directly at the laser source to avoid the risk of eye damage or blindness.

●

Do not insert fingers or foreign objects into the device to avoid the risk of electrical

shock, fire, malfunction, or personal injury.

●

Do not expose the device to high humidity or place liquid containers such as a flower

vase on the device to avoid the risk of electrical shock, fire, or malfunction.

●

Do not expose the device to temperature outside the range 5 – 35 °C (41 – 95 °F) to

avoid the risk of fire, deformation of the device panel, or malfunction.

●

Do not expose the device to dusty place to avoid the risk of fire or malfunction.

●

Always follow the owner’s manual to set up or connect the devices properly to avoid

the risk of electrical shock, fire, malfunction, or personal injury.

●

If unusual smells, sounds or smoke come from the device, or if foreign objects such

as liquid get into the device, turn off and unplug the computer immediately to avoid

the risk of electrical shock, fire, or malfunction. Contact the store of purchase or your

nearest Yamaha dealer (listed at the back of this manual).

●

Be sure that the computer is electrically grounded to avoid the risk of electrical shock.

●

Prior to cleaning the drive, always unplug the computer or do not handle the plug with

wet hands to avoid the risk of electrical shock.

●

Use the included AC adapter to avoid the risk of fire or malfunction.

iii

●

Clean the AC power plug regularly to avoid the risk of fire due to insulation failure

such as humidity.

●

Do not unplug the AC adapter by pulling the cable, and do not place objects on the

cable to avoid the risk of electrical shock, fire, or malfunction.

●

Plug in the AC adapter fully to avoid the risk of electrical shock or fire.

●

Do not connect many devices to an electrical outlet. Maintain the rated power of the

outlet to avoid the risk of fire due to overheating.

CAUTION

Always follow these basic precautions to avoid physical injury to yourself or others,

and damage to the device or other property.

●

Always unplug the computer if it will not be used for a prolonged period or if there is a

possibility of lightning, to avoid the risk of electrical shock, fire, or short-circuit.

●

Do not use the device near other electrical appliances such as televisions, radios, or

speakers to avoid the risk of interferences between each other.

●

Do not place the device unstably to avoid the risk of malfunction or personal injury by

its falling down.

●

Do not place the device with a possibility of excessive vibration to avoid the risk of

damage to written data or malfunction.

●

Place the device horizontally to avoid the risk of damage to written data.

●

Prior to transporting the device, remove the disc from the disc tray to avoid the risk of

damage to written data.

●

Use soft, dry cloths to wipe the device. Do not use benzene, paint thinner, detergents,

or chemically treated wiped cloths, and do not place vinyl, plastic, or rubber objects

on the device to avoid the risk of malfunction or damage to the surface of the device.

●

Do not rest your weight on or place heavy objects on the device, and do not apply

excessive force to the buttons, switches, or connectors to avoid the risk of damage to

the device or personal injury.

●

Be careful not to short-circuit the AC power plug with metal objects to avoid the risk of

malfunction.

●

Do not wrap the power cable around the AC adapter to avoid the risk of breaking the

wire or malfunction.

●

Do not listen to audio with headphones at high volume for prolonged period to avoid

auditory disorder.

●

Prior to turning on the computer, always minimize the volume to avoid auditory

disorder by a sudden burst of sound at high volume.

●

Do not place the device near magnets or anything magnetized such as a display to

avoid the risk of interferences between each other.

●

Have the device serviced regularly to avoid internal dust buildup that can cause

malfunction, damage or fire. For service information and service charges, contact the

store of purchase or your nearest Yamaha dealer (listed at the back of this manual).

WARRANTY

YAMAHA AND ITS SUPPLIERS ACCEPT NO LIABILITY FOR ANY PROBLEMS THAT OCCUR AS A

RESULT OF ANY OPERATIONS CARRIED OUT OTHER THAN THOSE STATED IN THE MANUAL

THAT COMES WITH THIS PRODUCT, OR THE LOSS OR THE DAMAGE OF ANY DATA CAUSED AS

A RESULT OF USING THIS PRODUCT.

Precautions for Transportation

Transporting the device unfixed may damage its internal mechanism or circuits.

• Remove the disc from the disc tray of the device.

• Put the device in the original box.

Prior to use, check that the complete accessories are included. (Refer to the original box.)

• This document may not, in whole or in part, be copied, photocopied, reproduced, translated,

transmitted, or reduced to any electronic medium of machine readable form without prior consent

in writing from Yamaha.

• Windows is a registered trademark of Microsoft Corporation.

• Apple, Macintosh, Mac OS, and FireWire are registered trademarks of Apple Computer, Inc.

• i.LINK is a trademark of Sony Corporation.

• SafeBurn™ is a trademark of Yamaha Corporation.

• All other trademarks are the property of their respective companies.

™ and ® marks are not specified in this manual.

Table of Contents

Features of the CRW3200IX Drive ................................................1

Names and Functions of Parts.....................................................3

Front Panel...............................................................................................3

Rear Panel................................................................................................4

Precautions on Use.................................................................. 5

Handling Discs ........................................................................................5

Disclaimer of Indemnity..........................................................................5

Compatible Discs.....................................................................................6

System Requirements ..............................................................................7

Preparing the CRW3200IX Drive .................................................10

Serial Number........................................................................................10

Set Up the CRW3200IX Drive on Windows.........................................11

Set Up the CRW3200IX Drive on Macintosh.......................................18

Connecting/Disconnecting the CRW3200IX Drive to/from the Computer...21

Loading/Ejecting a Disc ...........................................................22

Troubleshooting.....................................................................24

Firmware.............................................................................30

CRW3200IX Drive Specifications ................................................31

Technical Notes.....................................................................35

IEEE1394...............................................................................................35

Buffer Underrun Protection Function....................................................35

Connecting Multiple IEEE1394 Devices ..............................................36

Writing Methods....................................................................................37

For details about how to install and use the CD writing software, refer to the

documentation that comes with it.

• The information contained in this manual is subject to change without prior notice.

• Reproduction of this manual, either in part or in full, is expressly forbidden.

Features of the CRW3200IX Drive

High speed writing/reading

The CRW3200IX drive supports up to 24X-speed writing for CD-R discs, and up to

10X-speed writing/rewriting for CD-RW discs. In addition, the drive supports data

reading and digital audio data extraction at up to 40X speed.

Tip

• The Partial CAV method permits 24X-speed writing for CD-R discs.

• The CLV method and the 4X – 10X Full CAV method permit 10X-speed writing/

rewriting for CD-RW discs.

IEEE1394 interface

The CRW3200IX drive uses an IEEE1394 interface that enables you to use the drive

as soon as it is connected to the computer.

The CRW3200IX drive supports a hot plug function that enables you to connect/

disconnect the drive while the computer is turned on.

SafeBurn™ (Enhanced stability writing technology)

The generous 8 MB buffer memory provides sufficient data storage to enable stable

disc writing at high speeds. Even if data transfer from the computer is interrupted,

the Buffer Underrun Protection function is activated to save CD-R discs from a

writing error. (P. 35)

“Optimum Write Speed Control” adjusts the writing speed to the optimum rate for

every CD-R disc automatically. You can set the maximum writing speed with your

CD writing software.

• Optimum Write Speed Control can be activated when the maximum writing speed is

set at 12X or more.

• The minimum writing speed to be automatically selected is 8X. Manually set the

optimum writing speed if a writing speed supported by a disc is less than 8X.

High fidelity digital audio

The CRW3200IX drive supports extraction of digital audio data at up to 40X speed

using CD writing software, as well as recording digital audio with high fidelity even

at 24X-speed writing.

Note

Audio Master Quality Recording (High quality audio writing mode)

Audio Master Quality Recording enables you to create high quality audio CDs. This

mode is available for CD-R discs with a capacity of 650 MB and 700 MB. (P. 38)

Audio CDs that are created with Audio Master Quality Recording may not be played

back on certain audio recorders and CD-R/RW drives.

CD-MRW (CD Mount Rainier ReWriting)

CD-MRW is a new standard of packet writing. Compared to the ordinary packet

writing, CD-MRW provides many useful functions such as background formatting.

(P. 39)

Note

Names and Functions of Parts

➀

Disc tray

Holds the disc. It is opened or closed by

pressing the eject button. (P. 22)

➁

Manual eject hole

Forcibly opens the disc tray when the tray

cannot be opened by pressing the eject

button. (P. 23)

➂

Eject button

Press to open or close the disc tray. (P. 22)

➃

Headphone jack

Connects headphones or external speakers

to the drive; has stereo mini-jack

specifications.

➄

Headphone volume dial

Controls the volume of the headphones.

The volume increases as the dial is turned

to the right.

➅

LED

Indicates the operational status of the

CRW3200IX drive by its colors and

blinking patterns.

Lights or blinks blue

• Lights: Standby (with disc)

• Blinks: Opening/Closing disc tray, or

reading disc information (TOC)

• Blinks rapidly: Playback audio

• Blinks irregularly: Reading data

Lights or blinks purple

• Lights: Standby (no disc) or the disc tray

is open

• Blinks: Accessing for writing or test

writing

• Blinks rapidly: Writing

Blinks orange

• Malfunction

Front Panel

➅

➁

➃➄

➀➂

➀

LINE OUT jacks (L/R)

Connect audio devices such as external

speakers.

➁

POWER switch (STANDBY/ON)

Turns the power on/off. (P. 11, 13)

➂

DC-IN connector

Connects the included AC adapter. (P. 11)

➃

IEEE1394 ports

Connect the included IEEE1394 cable.

(P. 13 for Windows, P. 18 for Macintosh)

Rear Panel

➁➀

➂

➃

Precautions on Use

To avoid trouble, such as writing errors, loss of recorded data, and malfunction of

the drive, take the following precautions when handling discs.

• Do not place discs in a hot or damp place or where they will be exposed to direct

sunlight.

• Do not touch the disc surface. Hold the disc by the edge when handling it.

• Remove dust and dirt from the disc surface. Use an air spray to remove dust. The

disc surface may be scratched if strongly wiped with a dry cloth.

• Do not stick labels to the disc surface or write anything on it except where

designated.

• Do not clean discs with chemicals or detergents.

• Do not bend or drop discs.

It is prohibited by law to duplicate copyright material for non-personal use without

the prior consent of the copyright holder. When copying material with your CD-R/

RW drive, take due care not to infringe the copyright.

• Yamaha assumes no liability for the loss of any profits incurred as a result of the

loss or corruption of data written on a CD-R or CD-RW, for any loss or damage

caused by or arising out of extraordinary circumstances (including circumstances

that Yamaha has foreseen or could foresee), nor for any damages incurred or

claimed by a third party.

• After handling important data, make a comparison between the original and the

copied data (to confirm that the data has been copied properly).

• In no event shall Yamaha be liable for any damage to discs due to a buffer

underrun error (P. 35) or for any other reason, or the inability to use distributed

discs with your drive.

• Yamaha assumes no liability for the inability to write/playback discs because of

their format.

Handling Discs

Disclaimer of Indemnity

Discs that can be written on

The CRW3200IX drive can write on the following discs.

For the latest information about discs previously checked for compatibility with the

drive, refer to the following website.

YAMAHA CD-R/RW Drive website

URL: http://www.yamaha.co.jp/english/product/computer/

Compatible Discs

CD-R discs

• The CRW3200IX drive can write at 1X, 2X, 4X, 8X, 12X, 16X or 24X speed.

• CD-R discs can be played back on a CD-ROM drive or a CD player.

• 24X-speed writing is enabled with Partial CAV method. (P. 7)

• Check the writing speeds your disc supports prior to writing.

CD-RW discs

• The CRW3200IX drive can write/rewrite at 2X or 4X speed.

• CD-RW discs can be read/played back on a device (e.g. CD-ROM drive) that

supports “CD-RW” discs.

Some discs support only 2X speed.

High Speed CD-RW discs

• The CRW3200IX drive can write/rewrite at 4X, 8X or 10X speed.

• High Speed CD-RW discs can be read/played back on a CD-RW drive that

bears the High Speed CD-RW logo or a device (e.g. CD-ROM drive) that

supports “CD-RW” discs.

• When using the packet writing method (P. 38) for writing/rewriting onto High

Speed CD-RW discs, you can select the 4X – 10X Full CAV method. For more

information refer to the documentation that comes with your CD writing software.

(Your CD writing software must support the Full CAV method, as does the CD

Writing software that comes with the CRW3200IX drive.)

• The Full CAV method is recommended when opening and editing a file on a CD-

RW disc with an application software.

• In order to write, erase, read or play back High Speed CD-RW discs, use a CD-R/

RW drive that bears the High Speed CD-RW logo. When using a CD-ROM drive

to read/play back High Speed CD-RW discs, use a drive that supports CD-RW

discs.

If these discs are used with a CD-R/RW drive not bearing the High Speed CD-RW

logo, the discs may not be recognized, resulting in a computer not operating

properly or other malfunctions occurring.

Refer to the YAMAHA website below prior to attempting to read/play back these

discs on a YAMAHA CD-R/RW drive not bearing the High Speed CD-RW logo.

URL: http://www.yamaha.co.jp/english/product/computer/

Note

Precautions on Use

Partial CAV (Constant Angular Velocity)

The CLV (Constant Linear Velocity) method is generally used to write data on a CD-R

disc. In writing using the CLV method, the disc rotation speed is adjusted to keep the data

writing speed (data transfer rate) constant on all parts of the disc.

In contrast, the CAV (Constant Angular Velocity) method exercises control so as to keep

the disc rotation speed constant. Since the CAV method makes it possible to substantially

increase the maximum data transfer rate without straining of the drive, it is adopted today

for most CD-ROM drives.

CD formats define the constant linear density of written data so that the amount of written

data per disc rotation will increase as the writing point moves from the inner track to the

outer track.

With the CAV method, therefore, data is transferred at a higher rate when it is written on

the outer tracks of the disc. To achieve 24X-speed writing, the CRW3200IX drive

employs the Partial CAV method, which is a combination of the CAV method for inner

tracks and the CLV method for outer tracks.

The Partial CAV method controls the disc rotation speed so that the CRW3200IX drive

starts writing at 18X speed on inner tracks, increasing the speed to 24X as the read/write

head moves outward and holds the speed at 24X on outer tracks.

Tip

The CRW3200IX drive supports 8 cm discs.

Use only circular discs. Do not use any irregular shaped discs such as heart-shaped or

star-shaped discs to avoid the risk of malfunction.

The CRW3200IX drive is designed to operate in the following computer

environment. If your computer does not meet these requirements, the CRW3200IX

drive may not operate or write at the maximum speed.

For Windows

Computer (PC/AT compatible)

• CPU: Pentium II-class or higher, 300 MHz or faster

• RAM: 64 MB or more

64 MB or more is required (128 MB is recommended) for Windows 2000

Professional, while 128 MB or more is required (256 MB is recommended) for

Windows XP.

Note

System Requirements

•CD-ROM drive

The CRW3200IX drive cannot be used to boot the computer or to set up an operating

system.

• Hard drive space

Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating an image file, there must be enough free space on the hard drive to store

the image file in addition to the working area (a total of up to 900 MB).

However, hard drive space for image files is not required when directly writing

onto a CD-R/RW disc from a hard drive or CD-ROM using the CRW3200IX

drive (on-the-fly writing).

Image file

You can collect the data files to be written on a CD-R/RW disc into a single image file.

The image file is useful for writing the same data onto multiple discs. For details, refer

to the documentation that comes with the CD writing software.

• A spare PCI expansion slot or a CardBas slot for an IEEE1394 interface card

(if one hasn’t been installed or built-in)

• IEEE1394 port

An optional IEEE1394 interface card (OHCI compatible) is required to connect

the CRW3200IX drive for the computer without an IEEE1394 port.

The IEEE1394 interface cards that have been already recognized to support the

CRW3200IX drive are as follows.

For the latest information about IEEE1394 interface cards supporting the

CRW3200IX drive, refer to the following websites.

YAMAHA CD-R/RW Drive website

URL: http://www.yamaha.co.jp/english/product/computer/

Some IEEE1394 interface cards may not support the CRW3200IX drive. Even if the

interface card operates properly in the computer, the interface card may not support

IEEE1394 interface CD-R/RW drives. For details, refer to the documentation that

comes with the IEEE1394 interface card.

Yamaha recommends that you use an IEEE1394 interface card listed above that has

been recognized to support the CRW3200IX drive.

Note

Manufacturer Product Card Type

Advansys ASB30400 PCI

SIIG NN2603 PCI

Note

Continued on next page

04GB-PrecautionsOnUse.fm Page 8 Friday, November 16, 2001 4:02 PM

Precautions on Use

Operating system

Windows 98 Second Edition, Windows Me, Windows 2000 Professional, or

Windows XP.

CD writing software

The CRW3200IX drive requires CD writing software to write onto a CD-R/RW

disc. Use the CD writing software that supports the CRW3200IX drive.

For details about installing and using the CD writing software, refer to the

documentation that comes with the CD writing software.

For Macintosh

Computer (Macintosh with a FireWire port)

• CPU: PowerPC G3, 300 MHz or faster

• RAM: 64 MB or more

• CD-ROM drive

The CRW3200IX drive cannot be used to boot the computer or to set up an operating

system.

• Hard drive space

Writing data on a CD-R/RW disc requires 50 MB to 100 MB of free space as a

working area on the hard drive. When writing data on a CD-R/RW disc after

creating image file, there must be enough free space on the hard drive to store the

image file in addition to the working area (a total of up to 900 MB).

However, hard drive space for image file is not required when directly writing

onto a CD-R/RW disc from hard drive or CD-ROM using the CRW3200IX drive

(on-the-fly writing).

Image file

You can collect the data files to be written on a CD-R/RW disc into a single image file.

The image file is useful for writing the same data onto multiple discs. For details, refer

to the documentation that comes with the CD writing software.

Operating system

Mac OS 8.6 and 9 to 9.2 (Classic API with Mac OS X is not supported.)

CD writing software

The CRW3200IX drive requires CD writing software to write onto a CD-R/RW

disc. Use the CD writing software that supports the CRW3200IX drive.

For details about installing and using the CD writing software, refer to the

documentation that comes with the CD writing software.

Note

Preparing the CRW3200IX Drive

The serial number is printed on the label on the bottom of your CRW3200IX drive.

When you have a question about the drive or need user support services, the serial

number is required.

Please write the serial number down in the space below. It may be difficult to check

the serial number after setting up the drive or for any other reason.

Serial Number

Serial number

(10 characters: 3 letters +

7 numbers)

Preparing the CRW3200IX Drive (Windows)

Place the CRW3200IX drive horizontally.

Remove all IEEE1394 devices connected to the computer, and

turn on the computer.

Be sure that the power switch on the rear panel of the

CRW3200IX drive is turned off (STANDBY), and connect the

included AC adapter to the DC-IN connector of the drive.

The arrow on the adapter plug faces to the screw (the left side of the

connector).

Set Up the CRW3200IX Drive on Windows

Note

DC-IN connector

Screw Arrow

Connect the included power cable to the AC adapter (

➀

Connect the other end of the power cable to the wall socket

(

➁

• Use the included AC adapter only. Do not use other adapters.

• The AC adapter may become warm during use under normal conditions.

• The AC adapter consumes power, shown in the table below, while connected to

the wall socket even if the power switch of the CRW3200IX drive is turned off.

Remove the power cable from the wall socket when not using the CRW3200IX

drive for a prolonged period.

Note

Power source Power consumption

100 V, 120 V 0.8 W

220 V 0.9 W

230 V, 240 V 1.0 W

Power cable (included)

➀

➁

Sayfa yükleniyor ...

Yamaha CRW3200IX Kullanım kılavuzu

Marka: Yamaha

Model: CRW3200IX

Kategori: Optik disk sürücüleri

Tip: Kullanım kılavuzu

Bu kılavuz için de uygundur

CRW3200IX Series

PDF İndir

rapor

Diğer dillerde

français: Yamaha CRW3200IX Manuel utilisateur
italiano: Yamaha CRW3200IX Manuale utente
svenska: Yamaha CRW3200IX Användarmanual
Deutsch: Yamaha CRW3200IX Benutzerhandbuch
English: Yamaha CRW3200IX User manual
dansk: Yamaha CRW3200IX Brugermanual
suomi: Yamaha CRW3200IX Ohjekirja
Nederlands: Yamaha CRW3200IX Handleiding
română: Yamaha CRW3200IX Manual de utilizare

Yamaha CRW3200IX Kullanım kılavuzu

Bu kılavuz için de uygundur

Yamaha CRW3200IX Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler