Yamaha CDX-396 El kitabı

CD

X-

596

/4

96/396

Compact Disc Player

Lecteur Compact Disque

OWNER’S MANUAL

MODE D’EMPLOI

BEDIENUNGSANLEITUNG

BRUKSANVISNING

MANUALE DI ISTRUZIONI

MANUAL DE INSTRUCCIONES

GEBRUIKSAANWIJZING

G B

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

ATTENTION

L’emploi de commandes, de réglages ou un choix de

procédures différents des spécifications de cette

brochure peut entraîner une exposition à d’éventuelles

radiations pouvant être dangereses.

ACHTUNG

Die Verwendung von Bedienungselementen oder

Einstellungen oder die Durchführung von

Bedienungsvorgängen, die nicht in dieser Anleitung

aufgeführt sind, kann zu einem Kontakt mit

gefährlichen Laserstrahlen führen.

OBSERVERA

Användning av kontroller och justeringar eller

genomförande av procedurer andra än de som

specificeras i denna bok kan resultera i att du utsätter

dig för farlig strålning.

ATTENZIONE

Uso di controlli o regolazioni o procedure non

specificamente descritte può causare l’esposizione a

radiazioni di livello pericoloso.

PRECAUCIÓN

El uso de los controles o los procedimientos de ajuste

o utilización diferentes de los especificados en este

manual pueden causar una exposición peligrosa a la

radiación.

VOORZICHTIG

Gebruik van bedieningsorganen of instellingen, of

uitvoeren van handelingen anders dan staan

beschreven in deze handleiding kunnen leiden tot

blootstelling aan gevaarlijke stralen.

CAUTION

:

INVISIBLE LASER RADIATION

W

HEN OPEN AND INTERLOCKS DEFEATED.

DO NOT STARE INTO BEA

M

OR VIE

W

DIRECTLY

W

ITH OPTICAL INSTRUMENTS.

VARNING

:

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH

SPÄRRAR ÄR URKOPPLADE. STIRRA EJ IN I STRÅLEN OCH BETRAKTA EJ

STRÅLEN MED OPTISKA INSTRUMENT.

VARO!

:

NÄKYMÄTÖNTÄ AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA LASERSÄTEILYLLE. ÄLÄ TUIJOTA SÄTEESEEN ÄLÄKÄ KATSO

SITÄ OPTISEN LAITTEEN LÄPI.

VARO!

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA

OLET ALTTIINA NÄKYMÄTTÖMÄLLE

LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

VARNING!

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR

ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.

BETRAKTA EJ STRÅLEN.

LINE OUT DIGITAL

AUDIO OUT

OPTICAL

1

Varningsanvisning för laserstrålning. Placerad i apparaten.

(CDX-496, CDX-396)

LINE OUT DIGITAL AUDIO OUT

OPTICAL COAXIAL

1

(CDX-596)

English

E-1

CAUTION FOR MOVING THE UNIT

Before moving the unit, first remove the disc from the

unit, press POWER to turn the unit off, and then

disconnect the AC power plug from the wall outlet.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may result

in hazardous radiation exposure.

This compact disc player is

classified as a CLASS 1

LASER product.

The CLASS 1 LASER

PRODUCT label is located

on the rear exterior.

Laser component in this product is capable of emitting

radiation exceeding the limit for Class 1.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

The wires in the mains lead are coloured in accordance

with the following code:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed

as follows: The wire which is coloured BLUE must be

connected to the terminal which is marked with the letter

N or coloured BLACK. The wire which is coloured

BROWN must be connected to the terminal which is

marked with the letter L or coloured RED. Making sure

that neither core is connected to the earth terminal of the

three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the plug

supplied with this appliance, it should be cut off and an

appropriate 3 pin plug fitted. For details, refer to the

instructions described above.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous if

engaged in a live socket outlet.

● To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

● Install your unit in a well ventilated, cool, dry, clean place

— away from windows, heat sources, vibration, dust,

moisture, or cold. To avoid humming sounds, locate the

unit away from other electrical appliances, motors, and

transformers. To prevent fire or electrical shock, do not

expose to rain and water.

● Be sure to allow at least 10 cm of ventilation space at the

top, on left, right, and back sides of this unit.

● Do not operate the unit upside-down. It may overheat,

possibly causing damage.

● Never open the cabinet. If something drops into the set,

contact your dealer.

● Do not use force on switches, knobs or cords.

● When not planning to use this unit for long periods of time

(i.e., vacation, etc.), disconnect the AC power plug from

the wall outlet.

● Grounding or polarization — Precautions should be taken

so that the grounding or polarization of the unit is not

defeated.

● Do not clean the unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

● Be sure to read the “Troubleshooting” section on common

operating errors before concluding that your unit is faulty.

● Do not place another component on top of this unit, as

damage or discoloration on the surface of the unit may

result.

● To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

● When disconnecting the power cord from the wall outlet,

grasp the plug; do not pull the cord.

● Do not plug the AC power plug to the wall outlet before

you finish all connections.

● The voltage to be used must be the same as that

specified on this unit. Using this unit with a higher voltage

than that which is specified is dangerous and may result

in a fire or other type of accident causing damage.

YAMAHA will not be held responsible for any damage

resulting from use of this unit with a voltage other than

that which is specified.

● Sudden temperature changes and storage or operation in

an extremely humid environment may cause

condensation inside the cabinet.

CAUTION: Read this before operating your unit.

E-2

NOTES ABOUT DISCS

Discs playable with this unit

This compact disc player is designed only for playing

compact discs bearing the marks shown below. Never

attempt to load any other type of disc into the unit. The unit

will also play 8-cm (3-inch) compact discs.

.... Compact discs (digital audio)

The most popular discs for commercially

available audio CDs.

.... CD-RW (ReWritable) digital audio

discs

The discs repeatedly recordable by using

CD recorders for audio recording.

Recorded CD-RW discs can be played

only with CD players which have the

ability to play CD-RW discs.

Notes

● Be sure to use a CD-RW disc made by

a reliable manufacture.

● Be sure to use a CD-RW disc which

has at least one of the following

phrases on the disc or disc case.

FOR CONSUMER

FOR CONSUMER USE

FOR MUSIC USE ONLY

.... CD-TEXT discs

The discs recorded with text data such as

album titles, track titles and artist names.

These discs can be played with ordinary

CD players, however, the text data can be

displayed only with CD players which

have the ability to display such data.

CDX-596 can display text data

recorded on CD-TEXT discs.

Note

This compact disc player may not be able to play some

CD-RW discs or discs on which recording was not made

correctly.

To prevent a malfunction of this unit:

● Do not use any nonstandard shaped

disc (heart etc.) available on the

market because it might damage the

unit.

● Do not use a disc with tape, seals, or paste on it. If

you use such a disc, a disc may get stuck in the unit,

or damage to the unit may result.

Notes about handling compact discs

● Always handle the disc with care so that its surface is not

scratched.

● Compact discs are not subjected to wear during play, but

damage to the disc surface when the disc is being

handled can adversely affect the disc’s play.

● Be sure to use a felt-tip pen or similar writing tool when

writing on the label side of the disc. Do not use a ball-

point pen, pencil, or other hard-tipped writing tool, as

these may damage the disc and may adversely affect the

disc’s play.

● Do not warp discs.

● When a disc is not currently being used, remove it from

the unit and store in an appropriate case.

● When removing or storing a disc, be careful not to

scratch the playing surface.

● Compact discs are not affected by small particles of dust

or fingerprints on their playing surface, but even so they

should be kept clean. Wipe by using a clean, dry cloth.

Do not wipe with a circular motion; wipe straight outward

from the center.

● Do not try to clean the disc’s surface by using any type of

disc cleaner, record spray, anti-static spray or liquid, or

any other chemical-based liquid because such

substances might irreparably damage the disc’s surface.

● Do not expose discs to direct sunlight, high temperature

or high humidity for a long period of time because these

might warp or otherwise damage the disc.

No!

To play an 8-cm CD

Place it in the inner recessed area of the disc tray. Do not

put a normal (12-cm) CD on top of an 8-cm CD.

English

E-3

Thank you for selecting this YAMAHA compact disc player.

FEATURES

CAUTION .........................................................1

NOTES ABOUT DISCS ...................................2

FEATURES ......................................................3

UNPACKING ....................................................4

NOTES ABOUT THE REMOTE

CONTROL .......................................................4

CONNECTIONS.............................................. 5

IDENTIFICATION OF COMPONENTS ........... 6

BASIC OPERATION ....................................... 8

To pause play ............................................... 9

To stop play .................................................. 9

To turn off the power .................................... 9

To play directly from the desired track.......... 9

To skip to the beginning of the desired

track (SKIP SEARCH)................................ 10

To advance or reverse play rapidly

(MANUAL SEARCH) .................................. 10

Other useful functions ................................ 11

RANDOM-SEQUENCE PLAY ...................... 13

REPEAT PLAY.............................................. 13

PROGRAM PLAY ......................................... 14

INDEX SEARCH ........................................... 15

TRACK PROGRAMMING FOR

RECORDING TO TAPE ................................. 16

Automatic tape-programming..................... 16

Manual tape-programming ......................... 18

Random sequential tape-programming...... 19

Automatic searching for the peak level

on a disc..................................................... 20

CD SYNCHRONIZED RECORDING ............ 21

TROUBLESHOOTING.................................. 22

SPECIFICATIONS ........................................ 23

v CD-RW (ReWritable) Disc Playability

* Refer to page 2 for details.

v Program Play

v Random-Sequence Play

v Single Track/Entire Disc Repeat Play

v Automatic Spacing Function

v Track Programming Function Useful for

Recording Tracks Fitted onto Any Length

of Tape

v Automatic Peak Level Search Function

v CD Synchronized Recording

v Adjustable Display Brightness

v Remote Control Capability

v Optical Digital Output

CDX-596 only

v Coaxial Digital Output

v CD-TEXT Data Display Capability

CONTENTS

E-4

UNPACKING

Remote control RCA pin cable

Battery (size AA, R6, UM-3) x 2

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

TEXT/

TIME

SPACE

PROGCLEAR

TAPE

RANDOM

REPEAT

32

1

65

4

98

7

INDEX

+

I0

OUTPUT LEVEL

+–

0

Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories.

NOTES ABOUT THE REMOTE CONTROL

Battery installation

1. Turn the remote control over and remove the battery

compartment cover by sliding it in the direction of the

arrow.

2. Insert the batteries (AA, R6, UM-3 type) according to the

polarity markings on the inside of the battery

compartment.

3. Close the battery compartment cover.

Battery replacement

If you notice that the remote control must be used closer to

the main unit, the batteries are weak. Replace both

batteries with new ones.

Notes

● Use only AA, R6, UM-3 batteries for replacement.

● Be sure the polarities are correct. (See the illustration inside

the battery compartment.)

● Remove the batteries if the remote control will not be used for

an extended period of time.

● If batteries leak, dispose of them immediately. Avoid touching

the leaked material or letting it come in contact with clothing,

etc. Clean the battery compartment thoroughly before

installing new batteries.

Remote control operation range

Notes

● There should be no large obstacles between the remote control

and the main unit.

● If the remote control sensor is directly illuminated by strong

lighting (especially an inverter type fluorescent lamp etc.), the

remote control might not work properly. In this case,

reposition the main unit to avoid direct lighting.

CDX-396CDX-596, CDX-496

30°

Remote control

sensor

2

1

3

Within approximately

6 m

CDX-596 CDX-496 CDX-396

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

TIME

SPACE

PROGCLEAR

TAPE

RANDOM

REPEAT

32

1

65

4

98

7

INDEX

+

I0

OUTPUT LEVEL

+–

0

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

TIME

SPACE

PROGCLEAR

TAPE

RANDOM

REPEAT

32

1

65

4

98

7

INDEX

+

I0

0

English

E-5

CONNECTIONS

● Before making any connection, switch OFF the power to

the unit and the amplifier or other component.

● Connections should be made to the correct input

terminals of the amplifier or another component.

● If the placement of this unit causes noise to another

equipment, such as a tuner, separate them from each

other.

When the LINE OUT (analog) terminals of

this unit are used ( 1 )

Connect these terminals to the “CD” (or “AUX”) terminals of

the amplifier. For additional details concerning these

connections, refer to the operation instructions of the

amplifier being used.

* Be sure that the left (“L”) and right (“R”) of these terminals are

connected to the corresponding (left and right) terminals of the

amplifier or another component.

When the DIGITAL AUDIO OUT (OPTICAL)

terminal of this unit is used ( 2 )

● Before using this terminal, pull out the terminal’s cover.

● Make the connection from this terminal to the optical

input terminal of an amplifier by using a commercially

available optical fiber cable.

* Use an optical fiber cable that conforms to EIAJ

standards. Other cables might not function correctly.

● Be sure to attach the terminal’s cover when this terminal

is not being used, in order to protect the terminal from

dust.

● This terminal can also be connected to the optical input

terminal of an MD recorder etc. to record CD onto MD

directly.

When the DIGITAL AUDIO OUT (COAXIAL)

terminal of this unit is used ( 3 )

CDX-596 only

Make the connection from this terminal to the digital input

terminal of an amplifier by using a connection cable.

To connect this unit to your amplifier, choose one of the ways listed below.

CD DIGITAL IN

OPTICAL

COAXIAL

LINE OUT DIGITAL AUDIO OUT

OPTICAL COAXIAL

1

RCA pin cable

(included)

1

Optical fiber cable

(not included)

2

Connection cable

(For CDX-596 only; not included)

3

Amplifier

To AC outlet

The shaded part ( ) is provided for CDX-596 only.

CDX-596 and CDX-496 only

●

The level of signals output from any of these terminals

into an amplifier can be adjusted by using the

–

OUTPUT LEVEL

+

buttons.

●

When using the DIGITAL AUDIO OUT (OPTICAL or

COAXIAL) terminal, set the level of signals output into

an amplifier to max. by using the

–

OUTPUT LEVEL

+

buttons.

E-6

FRONT PANEL

● The control functions on the main unit and on the remote

control are virtually identical, with the exceptions below.

IDENTIFICATION OF COMPONENTS

( ) indicates the page number on which the controls are best described.

NATURAL SOUND COMPACT DISC PLAYER

AUTO

DISPLAY OFF

POWER

10

1 2 3 4 5 6 7 8 9 0

SKIP/SEARCH

OUTPUT LEVEL

PHONES

OPEN/CLOSE

NATURAL SOUND COMPACT DISC PLAYER

OPEN/CLOSE

POWER

10

1 2 3 4 5 6 7 8 9 0 SKIP/SEARCH

CDX-396

● / (play/pause) on the main unit has both the

functions of (play) and (pause) on the remote

control.

● SKIP/SEARCH on the main unit has both the

functions of / (skip) and / (search) on

the remote control.

CDX-596, CDX-496

POWER (p. 8)

AUTO DISPLAY OFF indicator CDX-596 only (p. 12)

Display panel

Disc tray (p. 8)

Remote control sensor (p. 4)

PHONES jack (p. 12)

POWER (p. 8)

Remote control sensor (p. 4)

Display panel

Disc tray (p. 8)

The shaded part ( ) is provided for CDX-596 only.

English

E-7

( ) indicates the page number on which the controls are best described.

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

SPACE

PROGCLEAR

TAPE

RANDOM

REPEAT

32

1

65

4

98

7

INDEX

+

I0

OUTPUT LEVEL

+–

0

TEXT/

TIME

CDX-596

CDX-496, 396

DIMMER (p. 12)

SYNCHRO (p. 21)

SPACE (p. 12)

TAPE (p. 16)

Numeric buttons (p. 9)

REPEAT (p. 13)

RANDOM (p. 13)

CDX-596 and CDX-496 only

OUTPUT LEVEL (p. 12)

INDEX (p. 15)

CLEAR (p. 15)

PROG (p. 14)

PEAK (p. 20)

OPEN/CLOSE (p. 8)

“pause” (p. 9)

/ “skip” (p. 10)

“stop” (p. 9)

/ “search” (p. 10)

“play” (p. 8)

TEXT/TIME (p. 11)

TIME (p. 11)

The shaded parts ( ) vary between models.

REMOTE CONTROL

E-8

BASIC OPERATION

This manual describes how to operate this unit by using the remote control.

To operate this unit from the front panel, use the corresponding buttons on the front panel.

1 Press POWER to turn on the power.

2 Press OPEN/CLOSE to open the disc tray, and load

a disc.

3 Press OPEN/CLOSE to close the disc tray.

4 Press (or ) to begin play.

Play will begin from the first track of the disc.

Display information

CDX-596

CDX-496, CDX-396

NATURAL SOUND COMPACT DISC PLAYER

POWER

1

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

SPACE

PROGCLEAR

TAPE

2

3

RANDOM

REPEAT

2, 3

4

POWER

OPEN/

CLOSE

OPEN/

CLOSE

1 Shows the track number selected or being played.

2 Displays the numbers that correspond to the numbers

of tracks (as high as number 20) on the disc. After each

track is played, its corresponding number disappears so

the number of remaining tracks (and their numbers) can

be seen at a glance.

3 CDX-596 and CDX-496

only

Shows the level of signals output into an amplifier or the

headphone level adjusted by pressing

–

OUTPUT

LEVEL

+.

4 Shows the time displays. (Refer to “Changing displays”

on page 11.)

143

2

123

4

11 12

345678910

Label side up.

Disc tray

English

E-9

Notes

● After closing the disc tray by pressing OPEN/CLOSE, the

display shows the total number of tracks and the total recorded

time of the disc for a few seconds.

CDX-596

CDX-496, CDX-396

Example: To select track 25

Press +10 twice, then immediately press 5 once.

* If a track number higher than the highest track number on the

disc is selected, the last track on the disc will be played.

To pause play

Press .

To resume play, press again (or press ).

* on the front panel can also be used to stop play

temporarily or to resume play.

● Additionally, you can close the disc tray by pressing

( ), a numeric button or RANDOM, or by pressing the

front edge of the disc tray gently. If the tray is closed in one of

these ways, play will begin automatically; however, the display

will not show the total number of tracks nor the total recorded

time of the disc.

● CDX-596 only

If you load a CD-TEXT disc, the display also shows the disc

title after showing the total number of tracks and the total

recorded time of the disc.

+

I0

5

To turn off the power

Press POWER again.

* If you turn on the power again with a disc still on the tray, the

disc starts playing automatically from the first track.

To play directly from the desired track

Select a desired track by using the numeric buttons.

To select track number 10 or higher

Press +10 to select the first digit and then press a numeric

button (1–0) to select the second digit.

1

11

2

12

345678910

TOTAL

Gear wheel

Caution

When the disc tray is open, do not touch the inside gear

wheel. If you touch the gear wheel, your finger may be

caught in the closing tray and injured.

CDX-596

CDX-496, CDX-396

The selected track

number is displayed

To stop play

Press .

+

5

E-10

To advance rapidly

(Press and hold.)

To reverse rapidly

(Press and hold.)

To advance or reverse play rapidly (MANUAL SEARCH)

● The sound can be heard (although slightly garbled)

during manual search in either direction. This is

convenient for locating a precise position within a track, or

for reviewing the contents quickly.

● Manual search can also be performed while disc play is

paused, though no sound will be heard.

● When using SKIP/SEARCH on the front

panel:

Be careful not to release the button just after it is

pressed, otherwise the play is skipped to the beginning

of the next track or returned to the beginning of the

current track.

To play from the beginning of the next track

To play from the beginning of the current track

To play from the beginning of the preceding track

● These operations can also be performed when the unit is

paused or stopped.

● When using or on the remote control:

If (or ) is pressed and held, the track number

is continuously changed to higher numbers (or lower

numbers).

● When using SKIP/SEARCH on the front panel:

Be careful not to press and hold the button, otherwise

the selected track is played forward (or backward)

rapidly.

To skip to the beginning of the desired track (SKIP SEARCH)

(Press once.)

(Press twice.)

English

E-11

Changing displays

CDX-596

You can select any of the four time displays (1 – 4) by pressing TEXT/TIME. When you play a CD-TEXT disc, the disc title,

artist name, and track name (5 – 7) are also displayed.

CDX-496 and CDX-396

You can select any of the four time displays by pressing TIME.

11

2

12

345678910

11

2

12

345678910

11

2

12

345678910

TITLE

CD-TEXT

11

2

12

345678910

ARTIST

CD-TEXT

11

2

12

345678910

TRACK

CD-TEXT

11

2

12

345678910

11

2

12

345678910

1Elapsed time of the current track

2 Remaining time of the current track

3 Total disc play time

4 Total remaining time on the disc 5 Disc title

6 Artist name

7 Track name

TOTAL

REMAIN

TOTAL

1 Elapsed time of the current track

2 Remaining time of the current track 3 Total disc play time

4 Total remaining time on the disc

TIME

TEXT/

TIME

Other useful functions

Notes

● The disc title, artist name, or track name may not be displayed with some CD-TEXT discs. In that case, “(NO ENTRY)” appears on the

display.

● When playing a CD-TEXT disc, “CD-TEXT” also lights up on displays 1 – 4.

E-12

Changing brightness of the display

CDX-596

You can change the brightness of the display (or turn off the illumination) by pressing DIMMER.

During play

Normal illumination

Dim

(off)*

* While the display illumination is off,

the AUTO DISPLAY OFF indicator

on the front panel lights up.

During a stop or a pause

Normal illumination

Dim

Dim*

* The AUTO DISPLAY OFF indicator lights up.

If a disc is played in this state, the display

illumination will be turned off.

CDX-496, CDX-396

If desired, you can change brightness of the display

in three degrees by pressing DIMMER.

Adjusting the level of signals output to the amplifier and the headphone listening level

CDX-596 and CDX-496 only

Normal illumination

Slightly dim

Dim

PHONES

DIMMER

OUTPUT LEVEL

+–

AUTO

DISPLAY OFF

You can adjust the level of signals output to the amplifier by

pressing

–

OUTPUT LEVEL

+.

Automatic spacing

If you record a disc onto tape with an insufficient time space

between tracks, the tape deck will not be able to perform

blank search operations on the tape correctly. To prevent

such a search mistake of the deck, press SPACE and light

up “SPACE” on the display before recording. Spaces of

about 4 seconds are inserted between the tracks.

“SPACE” disappears

from the display.

Note

When the automatic spacing function is in effect, the display

of the total time and of the total remaining time will include

each of the 4 second intervals placed between tracks.

To cancel the automatic spacing function

Press SPACE.

SPACE

PHONES

When you listen with headphones,

connect the headphones to the

PHONES jack and adjust the

volume by pressing

–

OUTPUT

LEVEL

+. At that time, note that

this adjustment will also vary the

signal level output to the amplifier.

English

E-13

The unit can play the tracks on a disc in a random sequence.

RANDOM-SEQUENCE PLAY

To perform random-sequence play

Press RANDOM.

To cancel random-sequence play

Press or RANDOM.

Notes

● This feature will not function while programming, or during

programmed play.

● If (SKIP/SEARCH ) is pressed during random-

sequence play, the next randomly programmed track will be

played. If ( SKIP/SEARCH) is pressed, play will

return to the beginning of the current track.

● This indication appears while the unit is mixing up

tracks.

● Total remaining time on the disc will not be displayed during

random-sequence play.

● CDX-596 and CDX-496 only

If the power is switched off during random-sequence play,

pressing POWER again to turn on the unit will automatically

restore random-sequence play.

You can play any desired track or the entire disc repeatedly by pressing REPEAT. The repeat play mode will change whenever

you press REPEAT.

REPEAT PLAY

CDX-596

(off)

CDX-496, CDX-396

(off)

SINGLE REPEAT (S)

A single track is played repeatedly.

* This also works for programmed play and random-sequence

play. (If repeat play is switched off, programmed play or

random-sequence play will be resumed.)

FULL REPEAT (F)

All tracks (the entire disc) are played repeatedly.

* During programmed play, all programmed tracks are played

repeatedly.

* During random-sequence play, all randomly sequenced tracks

are played repeatedly in the same order.

* CDX-596 and CDX-496 only

If the power is switched off during FULL REPEAT play,

pressing POWER again to turn on the unit will automatically

restore FULL REPEAT play.

RANDOM

or

REPEAT

REPEAT S

REPEAT F

SINGLE

REPEAT

FULL

REPEAT

E-14

You can enjoy listening to your favorite tracks in any desired order by programming tracks. As many as 40 tracks can be

programmed in sequence.

PROGRAM PLAY

1

Press to stop the unit.

2 Press PROG.

3 Program a desired track by

pressing the corresponding

numeric button.

Repeat this operation to program more tracks.

You can select the same track again.

4 When programming is finished,

press PROG.

5 Press to begin play.

Display information during programming

CDX-596

CDX-496, CDX-396

1

Shows the program number for the track to be

programmed next.

2 Shows the selected track number.

3 Shows only the numbers of programmed tracks.

4 Shows the total time of the tracks currently

programmed.

* If the total time becomes 100 minutes or more, the first

digit will not be displayed.

Notes

● If, during programming, TIME is pressed, the program number

display can be changed to display the total time of the

programmed tracks. To return to the previous display, press

TIME once again.

● / ( SKIP/SEARCH ) can be used during

playing, but only within the range of the programmed tracks.

● / ( SKIP/SEARCH ) can be used during

playing to search all tracks, including unprogrammed tracks.

PROG

6

PROGCLEAR

TAPE

32

1

65

4

98

7

INDEX

+

I0

0

3

2, 4

RANDOM

REPEAT

5

1

6

1

PROGRAM

6

2

3

4

TOTAL

PROGRAM

2

3

TOTAL

PROGRAM

1

4

PROGRAM

TOTAL

PROGRAM

Blinks.

CDX-596

CDX-496, CDX-396

PROG

English

E-15

To stop program play

Press . The first programmed track number will be

displayed.

To resume play, press . Play will begin from the

beginning of the program.

To clear program data

There are several methods, as described below.

● Press or CLEAR while the unit is stopped.

● Open the disc tray.

● Switch off the power.

To check program data

1. If during program play, press .

2. Press PROG.

3. Each time (SKIP/SEARCH ) is pressed, the

track numbers and sequential order of the programmed

tracks can be checked one after another. The display of

the track number can be returned (sequentially in

reverse order) by pressing ( SKIP/SEARCH).

To correct program data

1. Follow the procedure described in “To check program

data”.

2. Display the track number to be corrected by pressing

/ ( SKIP/SEARCH ).

3. Press a numeric button to select a desired track to

replace the one displayed. The previously programmed

track will be cleared from the memory, and the new one

will be programmed.

4. Press PROG to complete the correction. To begin play

immediately after making the correction, press

instead of pressing PROG.

If the disc includes index numbers, play can be started from any desired index number.

INDEX SEARCH

1

Press a numeric button to select a track which has

index numbers.

2 Press INDEX.

3 Press a numeric button to select the desired index

number.

To cancel the index search function

Press INDEX.

Notes

● Not all discs have index numbers. In addition, among those

discs which have index numbers, not all discs necessarily have

more than one index number.

● The index system is a method for sub-dividing tracks into

smaller divisions for easier location of those parts. The liner

notes contained in the disc case usually tell that such index

numbers are included with the mark.

● If an index number is selected that is higher than any index

number on that disc, play will start from the last index point on

the disc.

● For some discs, play may begin slightly prior to the actual

designated index point.

● If the disc has no encoded index points, play will begin from

the beginning of the selected track.

● The index number can be designated only while “INDEX” is

illuminated.

INDEX

5

6

INDEX

11 12

5678910

CDX-596

CDX-496, CDX-396

E-16

46

60 90

54

The unit can program tracks on a disc for recording onto tape. By considering the tape’s total possible recording time, the unit

will automatically program tracks or help you program tracks so they will fit onto the tape with the least amount of unrecorded

space at each end of the tape.

TRACK PROGRAMMING FOR RECORDING TO TAPE

m Automatic tape-programming

The unit will automatically program tracks on a disc with their original order.

1 Press to stop the unit.

* The peak level search function of this unit is useful for

adjusting recording level on the tape deck. (Refer to page

20.)

2 If desired, you can automatically insert additional

time space between tracks by pressing SPACE to

light up “SPACE” on the display. (Refer to page 12.)

3 Press TAPE to show the tape’s total possible

recording time on the display.

You can select any of the four tape lengths by

pressing TAPE.

If desired, you can also enter the tape’s total possible

recording time manually.

Example: For a C-64 tape (32 minutes on each side),

press “6” and “4”.

+

4 Press REPEAT.

The unit automatically programs tracks for both side A

and side B considering the tape’s total time.

5 Begin recording on the tape deck, and then press

on this unit.

6 The unit will pause at the end of side A of the tape.

Turn the tape over to side B. Resume recording,

and then press or on this unit.

RANDOM

REPEAT

PEAK

SPACE

PROGCLEAR

TAPE

32

1

65

4

98

7

INDEX

+

I0

0

TEXT/

TIME

2

3

4

6

5, 6

1

SPACE

TAPE

REPEAT

6

4

SPACE

CDX-596

“TAPE 46” turns on.

CDX-496, CDX-396

“C-46” turns on.

(off)

English

E-17

Notes

● In step 4, you can check the program data for side A and side

B.

CDX-596

CDX-496, CDX-396

1

Shows the number of tracks programmed on each side

right after the programming is finished. It is then replaced

by the number of the first programmed track on side A.

2 Shows the programmed track numbers on each side.

3 Shows the total time of programmed tracks on each side.

4 Shows the side of the tape.

● All tracks may not be programmed if the tape’s length is not

enough. To program all tracks, use a tape that is longer than

the actual playing time.

● To check, cancel or correct program data, refer to page 15.

* When checking program data, note that “PAUSE” or “Pu”

appears between track numbers for side A and side B.

● Up to 40 tracks can be programmed. A pause inserted between

side A and B is counted as one track.

● CD synchronized recording function can be used if your tape

deck is compatible with it. If so, in step 5 and 6, press

SYNCHRO and then press on this unit’s remote control.

Recording automatically begins. (For details, refer to page 21.)

1324

PROGRAM

12345

A

TOTAL

PROGRAM

A

13

2

4

E-18

m Manual tape-programming

This is for recording desired tracks in any order onto a tape.

1 Follow steps 1 – 3 on page 16.

2 Press PROG.

3 Use numeric buttons to select desired tracks (to be

recorded on side A) in any order.

* Programmed track numbers light up on the display. You can

select a track which can be programmed for the remaining

time on side A from track numbers flashing on the display.

You cannot, however, select a track number extinguished

from the display.

4 When track selection for side A is finished, press

TAPE.

A pause is inserted.

5 Use numeric buttons to select the track numbers (to

be recorded on side B) in any order.

6 Begin recording on the tape deck, and then press

on this unit.

7 The unit will pause at the end of side A of the tape.

Turn the tape over to side B. Resume recording,

and then press or on this unit.

Notes

● If, in step 3 or 5, “ERROR” or “E rr” appears on the display,

the track number just selected cannot be programmed because

there is not enough time remaining on the tape. However, at

this time, if any other track number is flashing continuously on

the display, you can program it instead of the unprogrammable

one.

● In step 3 or 5, each time a selection is made, the track number

and the tape’s remaining time will be displayed, and then the

display will change to indicate the next program number.

● To check, cancel or correct program data, refer to page 15.

* When checking program data, note that “PAUSE” or “Pu”

appears between track numbers for side A and side B.

● Up to 40 tracks can be programmed. If, however, a pause is

inserted, it is counted as one track.

● CD synchronized recording function can be used if your tape

deck is compatible with it. If so, in step 6 and 7, press

SYNCHRO and then press on this unit’s remote control.

Recording automatically begins. (For details, refer to page 21.)

OPEN/

CLOSE

DIMMERSYNCHRO

PEAK

SPACE

PROGCLEAR

TAPE

32

1

65

4

98

7

INDEX

+

I0

0

TEXT/

TIME

RANDOM

REPEAT

4

3, 5

2

7

6, 7

PROG

32

1

65

4

98

7

+I0

0

TAPE

32

1

65

4

98

7

+

I0

0

PROGRAM

1

11

2

12

345678910

A

TOTAL

REMAIN

PROGRAM

A

CDX-596

CDX-496, CDX-396

Blinks.

Sayfa yükleniyor ...

Yamaha CDX-396 El kitabı

Bu kılavuz için de uygundur

Yamaha CDX-396 El kitabı

Diğer dillerde

İlgili Makaleler

Diğer Belgeler