Yamaha RX-SL100 El kitabı

Kategori
AV alıcıları
Tip
El kitabı
YAMAHA ELECTRONICS CORPORATION, USA
6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD.
135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H.
SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A.
RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD.
YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B.
J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD.
17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
©
2003 All rights reserved.
RX-SL100RDS
AV Receiver
Ampli-tuner audio-vidéo
RX-SL100RDS
OWNER'S MANUAL
MODE D'EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
GB
INPUT
VOLUME/SELECT
DSPTUNER
AUTO/MAN'L
PUSH-ENTER
STANDBY
/ON
PHONES VIDEO AUDIO
VIDEO 2
SILENT
OPTICALL R
Printed in Malaysia WC19140-1
00_RXSL100_RDS_cv.fm Page 1 Wednesday, November 26, 2003 1:29 PM
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
2 Install this sound system in a well ventilated, cool,
dry, clean place — away from direct sunlight, heat
sources, vibration, dust, moisture, and/or cold.
Allow ventilation space of at least 5 cm on the top,
5 cm on the left and right, and 10 cm on the back of
this unit.
3 Locate this unit away from other electrical
appliances, motors, or transformers to avoid
humming sounds.
4 Do not expose this unit to sudden temperature
changes from cold to hot, and do not locate this
unit in a environment with high humidity (i.e. a
room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal
injury.
5 Avoid installing this unit where foreign object may
fall onto this unit and/or this unit may be exposed
to liquid dripping or splashing. On the top of this
unit, do not place:
Other components, as they may cause damage
and/or discoloration on the surface of this unit.
Burning objects (i.e. candles), as they may
cause fire, damage to this unit, and/or personal
injury.
Containers with liquid in them, as they may fall
and liquid may cause electrical shock to the user
and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation.
If the temperature inside this unit rises, it may
cause fire, damage to this unit, and/or personal
injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may
overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used.
Using this unit with a higher voltage than specified
is dangerous and may cause fire, damage to this
unit, and/or personal injury. YAMAHA will not be
held responsible for any damage resulting from use
of this unit with a voltage other than specified.
13 To prevent damage by lightning, disconnect the
power cord from the wall outlet during an electrical
storm.
14 Do not attempt to modify or fix this unit. Contact
qualified YAMAHA service personnel when any
service is needed. The cabinet should never be
opened for any reasons.
15 When not planning to use this unit for long periods
of time (i.e. vacation), disconnect the AC power
plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section
on common operating errors before concluding
that this unit is faulty.
17 Before moving this unit, press STANDBY/ON to set
this unit in the standby mode, and disconnect the
AC power plug from the wall outlet.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
The plug severed from the mains lead must be destroyed, as a
plug with bared flexible cord is hazardous if engaged in a live
socket outlet.
Special Instructions for U.K. Model
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
if this unit itself is turned off. This state is called the
standby mode. In this state, this unit is designed to
consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
Note
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows:
The wire which is coloured BLUE must be connected
to the terminal which is marked with the letter N or
coloured BLACK. The wire which is coloured
BROWN must be connected to the terminal which is
marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
01EN.00_RX-SL100RDS.book Page i Thursday, November 27, 2003 12:42 PM
1
English
PREPARATIONINTRODUCTION
BASIC
OPERATION
SOUND FIELD
PROGRAMS
ADVANCED
OPERATION
ADDITIONAL
INFORMATION
FEATURES............................................................. 2
GETTING STARTED............................................ 3
Supplied accessories .................................................. 3
Installing batteries in the remote control ................... 3
CONTROLS AND FUNCTIONS ......................... 4
Front panel ................................................................. 4
Remote control (AMP mode) .................................... 5
Using the remote control ........................................... 6
Front panel display .................................................... 7
SPEAKER SETUP ................................................. 8
Speaker placement ..................................................... 8
Speaker connections .................................................. 9
CONNECTIONS .................................................. 12
Before connecting components................................ 12
Connecting other components ................................. 12
Connecting the antennas.......................................... 14
Connecting the power.............................................. 15
Turning on the power............................................... 15
BASIC SETUP...................................................... 16
Using BASIC setup.................................................. 16
PLAYBACK.......................................................... 19
Basic operations....................................................... 19
Selecting sound field programs ............................... 20
TUNING ................................................................ 22
Automatic and manual tuning.................................. 22
Presetting stations .................................................... 24
Selecting preset stations........................................... 25
Receiving RDS stations ........................................... 26
Changing the RDS mode ......................................... 27
PTY SEEK function ................................................ 27
EON function........................................................... 28
RECORDING ....................................................... 29
Recording in standby mode
(Standby SCART setting).................................... 29
SOUND FIELD PROGRAM
DESCRIPTIONS...............................................30
For Hi-Fi DSP programs.......................................... 30
For CINEMA-DSP programs .................................. 31
ADVANCED OPERATIONS ..............................32
Using the sleep timer ............................................... 32
Enjoying multi-channel software............................. 32
Enjoying 2-channel software ................................... 33
Virtual CINEMA DSP............................................. 34
Selecting input modes.............................................. 34
Manually adjusting speaker levels........................... 36
Using the test tone ................................................... 37
SET MENU ............................................................38
Changing parameter settings ................................... 39
SOUND menu.......................................................... 40
INPUT menu............................................................ 43
OPTION menu......................................................... 44
REMOTE CONTROL FEATURES ...................46
Control area ............................................................. 46
Setting manufacturer codes...................................... 47
Controlling other components ................................. 48
EDITING SOUND FIELD PARAMETERS ......49
What is a sound field ............................................... 49
Sound field parameter descriptions ......................... 49
TROUBLESHOOTING .......................................51
GLOSSARY...........................................................56
SPECIFICATIONS...............................................58
CONTENTS
INTRODUCTION
PREPARATION
BASIC OPERATION
SOUND FIELD PROGRAMS
ADVANCED OPERATION
ADDITIONAL INFORMATION
01EN.00_RX-SL100RDS.book Page 1 Thursday, November 27, 2003 12:42 PM
FEATURES
2
Built-in 6-channel original Yamaha digital
power amplifier
Minimum RMS output power
(0.9% THD, 1 kHz, 6)
Front: 70 W + 70 W
Center: 70 W
Surround: 70 W + 70 W
Surround Back: 70 W
(10% THD, 1 kHz, 4)
Front: 75 W + 75 W
Center: 75 W
Surround: 75 W + 75 W
Surround Back: 75 W
Sound field features
Proprietary YAMAHA technology for the creation of
sound fields
Dolby Digital/Dolby Digital EX, DTS/DTS-ES Matrix
6.1, Discrete 6.1, DTS Neo:6, Dolby Pro Logic/Dolby
Pro Logic II/Pro Logic IIx decoder
Virtual CINEMA DSP
SILENT CINEMA
Sophisticated AM/FM tuner
40-station random access preset tuning
Automatic preset tuning
Graphical User Interface (GUI)
Large on-screen display output to your TV monitor
“SET MENU” which provides you with items for
optimizing this unit for your audio/video system
Easy to use
Other features
96-kHz/24-bit D/A converter
Slim-line design
Optical and coaxial digital audio signal jacks
Sleep timer
Night listening mode
Remote control with preset manufacturer codes
y indicates a tip for your operation.
Some operations can be performed by using either the buttons on the main unit or on the remote control. In cases when the button
names differ between the main unit and the remote control, the button name on the remote control is given in parentheses.
This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In
case of differences between the manual and product, the product has priority.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
“DTS” and “DTS-ES Digital Surround” and “Neo:6” are
trademarks of Digital Theater Systems, Inc.
SILENT CINEMA is a trademark of YAMAHA
CORPORATION.
The following name plate is located on the bottom of this unit.
FEATURES
01EN.00_RX-SL100RDS.book Page 2 Thursday, November 27, 2003 12:42 PM
GETTING STARTED
3
English
INTRODUCTION
Please check that you received all of the following parts.
Insert the batteries in the correct direction by aligning the
+ and – marks on the batteries with the polarity markings
(+ and –) inside the battery component.
1 Remove the back cover.
2 Insert the two supplied batteries (AA, R6,
UM-3) into the battery compartment.
3 Close the back cover.
Notes on batteries
Change all of the batteries if you notice that the operation range
of the remote control has decreased.
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
GETTING STARTED
Supplied accessories
1
HALL
2
JAZZ
3
ROCK
4
ENTERTAIN
SLEEP
STANDBY/ON
5
MUSIC
6
TV THTR
7
MOVIE 1
8
MOVIE 2
9
TV AV
CODE SET
REC
s
FREQ/RDS
AUDIO
EON
w
DISC SKIP
e
MODE
PTY SEEK
f
START
b
A/B/C/D/E
TITLE
LEVEL
ENTER
CH
CH
+
p
d
MUTE
TV VOL VOLUME
AMP
VCRDVD/CD VIDEO 1
TUNERDTV/CBL VIDEO 2
PRESET
a
u
q/DTS
0
NIGHT
+10
EX/ES
ENT
STEREO
EFFECT
MUTE INPUT
CH
TV MODE
+
RX-SL100RDS
MENU
SET MENU
RETURN
TEST
DISPLAY
Remote control
Indoor FM antenna
(U.S.A., Canada, Asia and
General models)
(U.K., Europe and
Australia models)
Batteries (2)
(AA, R6, UM-3)
AM loop antenna
Remote control
Cable tags (6 pairs)
Installing batteries in the remote control
Check +/–
polarity
Press
If the remote control is without batteries for more than
3 minutes, or if exhausted batteries remain in the
remote control, the contents of the memory may be
cleared. When the memory is cleared, insert new
batteries, set up the manufacturer code and program
any acquired functions that may have been cleared.
01EN.00_RX-SL100RDS.book Page 3 Thursday, November 27, 2003 12:42 PM
CONTROLS AND FUNCTIONS
4
1 STANDBY/ON
Turns on this unit or sets it to the standby mode. When you
turn on this unit, you will hear a click and there will be a 4
to 5-second delay before this unit can reproduce sound.
In standby mode, this unit consumes a small amount of power in
order to receive infrared-signals from the remote control.
2 SILENT (PHONES jack)
Outputs audio signals for private listening with
headphones. When you connect headphones, no signals
are output to the OUTPUT jacks or to the speakers.
All Dolby Digital and DTS audio signals are mixed down
to the left and right headphone channels.
3 VIDEO 2 jacks
Input audio and video signals from a portable external
source such as a game console. To reproduce source
signals from these jacks, select VIDEO 2 as the input
source.
4 Remote control sensor
Receives signals from the remote control.
5 Front panel display
Shows information about the operational status of this
unit.
6 VOLUME/SELECT
Adjusts the volume. Also selects stations, sound field
programs or input sources (etc.) when used together with
TUNER, DSP or INPUT. If no operation is performed
within 5 seconds of pressing TUNER, DSP or INPUT, the
VOLUME/SELECT function automatically returns to
volume.
7 INPUT
Activates the input select mode.
Activates the AM, FM or preset tuning mode when
TUNER is selected as the input source.
8 DSP
Activates the DSP sound field select mode or STEREO
mode.
9 TUNER (AUTO/MAN’L)
Activates the tuning mode when TUNER is selected as the
input source. Press before turning VOLUME/SELECT to
tune in frequencies or preset radio stations.
Switches the AM/FM tuning mode between automatic
(“AUTO” indicator on) and manual (“AUTO” indicator
off) tuning.
CONTROLS AND FUNCTIONS
Front panel
INPUT
VOLUME/SELECT
DSPTUNER
AUTO/ MAN' L
PUSH-ENTER
STANDBY
/ON
PHONES VIDEO AUDIO
VIDEO 2
SILENT
OPTICALL R
12 3 5 6
789
4
Note
01EN.00_RX-SL100RDS.book Page 4 Thursday, November 27, 2003 12:42 PM
CONTROLS AND FUNCTIONS
5
English
INTRODUCTION
Make sure that the AMP mode is selected before starting
operation.
1 Infrared window
Outputs infrared control signals. Aim this window at the
component you want to operate.
2 STANDBY/ON
Switches the unit on and sets it in the STANDBY mode.
3 DSP program / Numeric buttons
Use to select sound field programs or input numbers
according to the current control area.
4 Operation buttons
Provide functions such as play, stop, skip, etc. for use
when operating other components.
5 LEVEL
Selects the speaker channel to be adjusted and sets the
level.
6 TEST
Outputs the test tone to adjust the speaker levels.
7 MUTE
Mutes the sound. Press again to restore the audio output to
the previous volume level.
8 AMP
Sets the remote control to the AMP mode for controlling
this unit (instead of the component selected using the
input selector buttons).
9 SLEEP
Sets the sleep timer.
0 NIGHT
Turns night listening mode on or off.
A EX/ES
Turns the Dolby Digital EX or DTS-ES decoder on or off.
B STEREO/EFFECT
Switches between normal stereo and DSP effect
reproduction. Select STEREO if you want this unit to
output pure sound from the front left and right speakers.
C CODE SET
Used to set up manufacturer codes.
Remote control (AMP mode)
1
HALL
2
JAZZ
3
ROCK
4
ENTERTAIN
SLEEP
STANDBY/ON
5
MUSIC
6
TV THTR
7
MOVIE 1
8
MOVIE 2
9
TV AV
CODE SET
REC
s
FREQ/RDS
AUDIO
EON
w
DISC SKIP
e
MODE
PTY SEEK
f
START
b
A/B/C/D/E
TITLE
LEVEL
ENTER
CH
CH
+
p
d
MUTE
TV VOL VOLUME
AMP
VCRDVD/CD VIDEO 1
TUNERDTV/CBL VIDEO 2
PRESET
a
u
q/DTS
0
NIGHT
+10
EX/ES
ENT
STEREO
EFFECT
MUTE INPUT
CH
TV MODE
+
RX-SL100RDS
MENU
SET MENU
RETURN
TEST
DISPLAY
1
2
3
5
6
7
8
9
F
0,A,B
C
D
E
G
4
01EN.00_RX-SL100RDS.book Page 5 Thursday, November 27, 2003 12:42 PM
CONTROLS AND FUNCTIONS
6
D SET MENU
Turns the SET MENU on or off.
E Multi control section
Use to select and adjust DSP program parameters or SET
MENU items.
F VOLUME +/
Increases or decreases the volume level.
G Input selector buttons
Use to select the input source and change the control area.
The remote control transmits a directional infrared beam.
Be sure to aim the remote control directly at the remote
control sensor on the main unit during operation.
Handling the remote control
Do not spill water or other liquids on the remote
control.
Do not drop the remote control.
Do not leave or store the remote control in the
following types of conditions:
high humidity such as near a bath
high temperature such as near a heater or stove
extremely low temperature
dusty places
Using the remote control
30 30
1
HALL
2
JAZZ
3
ROCK
4
ENTERTAIN
SLEEP
STANDBY/ON
5
MUSIC
6
TV THTR
7
MOVIE 1
8
MOVIE 2
9
TV AV
CODE SET
REC
s
FREQ/RDS
AUDIO
EON
w
DISC SKIP
e
MODE
PTY SEEK
f
START
b
A/B/C/D/E
TITLE
LEVEL
ENTER
CH
CH
+
p
d
MUTE
TV VOL VOLUME
AMP
VCRDVD/CD VIDEO 1
TUNERDTV/CBL VIDEO 2
PRESET
a
u
q/DTS
0
NIGHT
+10
EX/ES
ENT
STEREO
EFFECT
MUTE INPUT
CH
TV MODE
+
RX-SL100RDS
MENU
SET MENU
RETURN
TEST
DISPLAY
INPUT
VOLUME/SELECT
DSPTUNER
AUTO/MAN'L
PUSH-ENTER
STANDBY
/ON
PHONES VIDEO AUDIO
VIDEO 2
SILENT
OPTICALL R
Approximately 6 m (20 ft)
01EN.00_RX-SL100RDS.book Page 6 Thursday, November 27, 2003 12:42 PM
CONTROLS AND FUNCTIONS
7
English
INTRODUCTION
1 Processor indicators
When any of this unit’s decoders function, the respective
indicator lights up.
2 NIGHT indicator
Lights up when you select NIGHT LISTENING mode.
3 Headphones indicator
Lights up when headphones are connected.
4 CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound field
program.
5 Input source indicators
A cursor lights to show the current input source.
6 VOLUME level indicators
Indicate the volume level.
7 MUTE indicator
Flashes while the MUTE function is on.
8 SLEEP indicator
Lights up while the sleep timer is on.
9 MEMORY indicator
Flashes to show a station can be stored in memory.
0 Input channel indicators
Indicates the channel components of the input digital
signal.
A LFE indicator
Lights up when the input signal contains the LFE signal.
B AUTO indicator
Shows that this unit is in the automatic tuning mode.
C TUNED indicator
Lights up when this unit is tuned into a station.
D STEREO indicator
Lights up when this unit is receiving a strong signal for an
FM stereo broadcast while the “AUTO” indicator is lit.
E RDS indicators
(U.K. and Europe models only)
The name(s) of the RDS data offered by the currently
received RDS station light(s) up.
EON lights up when an RDS station that offers the EON
data service is being received.
PTY HOLD lights up while searching for stations in the
PTY SEEK mode.
F HiFi DSP indicator
Lights up when you select a HiFi DSP sound field
program.
G Multi-information display
Shows the current sound field program name and other
information when adjusting or changing settings.
H SILENT indicator
Lights up when headphones are connected and a sound
field program is selected (see page 20).
I VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 34).
J PCM indicator
Lights up when this unit is reproducing PCM (pulse code
modulation) digital audio signals.
Front panel display
VCR
PS PTY RT CT PTY HOLD EON STEREO TUNED
AUTO MEMORY
MUTE
VOLUME
SLEEP
DIGITAL
PL
PL
MATRIX DISCRETE
PCM
VIRTUAL
ES
EX
NIGHT
SILENT
LFE
ft
mS
dB
L
L C R
SL SB SR
HiFi DSP
VIDEO 1 VIDEO 2
DTV/CBL
TUNER
DVD/CD
1234 5 678
JI H G E A09BCDF
01EN.00_RX-SL100RDS.book Page 7 Thursday, November 27, 2003 12:42 PM
SPEAKER SETUP
8
y
The speaker layout above shows the standard ITU-R speaker
setting.
Front speakers (FR and FL)
The front speakers are used for the main source sound plus
effect sounds. Place these speakers an equal distance from
the ideal listening position. The distance of each speaker
from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds
(dialog, vocals, etc.). If for some reason it is not practical
to use a center speaker, you can do without it. Best results,
however, are obtained with the full system. Align the front
face of the center speaker with the front face of your video
monitor. Place the speaker centrally between the front
speakers and as close to the monitor as possible, such as
directly over or under it.
Surround speakers (SR and SL)
The surround speakers are used for effect and surround
sounds. Place these speakers behind your listening
position, facing slightly inwards, about 1.8 m (6 ft) above
the floor.
Surround back speaker (SB)
The surround back speaker supplements the surround
speakers and provide for more realistic front-to-back
transitions. Place this speaker directly behind the listening
position and at the same height as the surround speakers.
Subwoofer
The use of a subwoofer, such as the YAMAHA Active
Servo Processing Subwoofer System, is effective not only
for reinforcing bass frequencies from any or all channels,
but also for high fidelity reproduction of the LFE (low-
frequency effect) channel included in Dolby Digital and
DTS software. The position of the subwoofer is not so
critical, because low bass sounds are not highly
directional. But it is better to place the subwoofer near the
front speakers. Turn it slightly toward the center of the
room to reduce wall reflections.
SPEAKER SETUP
Speaker placement
60˚
30˚
SB
FL
FR
C
SL
SR
SR
80˚
SL
1.8 m
01EN.00_RX-SL100RDS.book Page 8 Thursday, November 27, 2003 12:42 PM
9
English
SPEAKER SETUP
PREPARATION
Be sure to connect the left channel (L), right channel (R),
“+” (colored) and “–” (black) properly. If the connections
are faulty, no sound will be heard from the speakers, and if
the polarity of the speaker connections is incorrect, the
sound will be unnatural and lack bass.
If you will use 6 ohm speakers, be sure to set this unit’s
speaker impedance setting to 6 ohms before using (see
“IMPEDANCE SELECTOR switch” on page 10).
Before connecting the speakers, make sure that the
power of this unit is off.
Do not let the bare speaker wires touch each other or do
not let them touch any metal part of this unit. This
could damage this unit and/or speakers.
Use magnetically shielded speakers. If this type of
speakers still creates the interference with the monitor,
place the speakers away from the monitor.
A speaker cord is actually a pair of insulated cables
running side by side. One cable is colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+”
(colored) terminals on this unit and your speaker. Connect
the plain cable to the “–” (black) terminals.
1 Remove approximately 10 mm (3/8") of
insulation from each of the speaker cables.
2 Twist the exposed wires of the cable together
to prevent short circuits.
3 Press and hold the tab to insert the speaker
wire.
4 Return the tab to secure the wire.
Cable tags
6 pairs of different colored cable tags are provided with
this product. The colors of the cable tags and their
respective speaker cables are as follows:
Red: Front right speaker cable
White: Front left speaker cable
Green: Center speaker cable
Gray: Surround right speaker cable
Blue: Surround left speaker cable
Brown: Surround back speaker cable
To make it easier to distinguish the various speaker cables,
attach the colored tags to the appropriate speaker cables as
shown below.
Speaker connections
CAUTION
10 mm (3/8")
1
2
R
R
L
Colored: positive (+)
Black: negative (–)
01EN.00_RX-SL100RDS.book Page 9 Thursday, November 27, 2003 12:42 PM
10
SPEAKER SETUP
IMPEDANCE SELECTOR switch
Do not change the setting of the IMPEDANCE
SELECTOR switch when the unit power is switched on,
as doing so may damage the unit.
If this unit fails to turn on when STANDBY/ON is pressed
on either the front panel or remote control, the
IMPEDANCE SELECTOR switch may not be fully slid to
either position. If this is the case, slide the switch all the
way to either position when this unit is in standby mode.
Be sure to move this switch only when this unit is in
standby mode.
Select the switch position (top or bottom) according to the
impedance of the speakers in your system.
Switch
position
Speaker Impedance level
Top
Front
The impedance of each speaker
must be 4 or higher.
Center, Surround
back, Surround
Bottom
Front
The impedance of each speaker
must be 6 or higher.
Center, Surround
back, Surround
CAUTION
MAINS
IMPEDANCE SELECTOR switch
01EN.00_RX-SL100RDS.book Page 10 Thursday, November 27, 2003 12:42 PM
11
English
SPEAKER SETUP
PREPARATION
Speaker connections
FRONT terminals
Connect your speaker system to these terminals.
SURROUND terminals
Connect surround speakers to these terminals.
SURROUND BACK terminals
Connect a surround back speaker to these terminals.
CENTER terminals
Connect a center speaker to these terminals.
SUBWOOFER OUTPUT jack
Connect a subwoofer with built-in amplifier, such as the
YAMAHA Active Servo Processing Subwoofer System,
to this jack.
y
You can easily distinguish between the cable pairs by attaching a
supplied cable tag to each end of the respective speaker cable (see
page 9).
The cut-off frequency for the SUBWOOFER jack is 90 Hz.
If you are not using a subwoofer, allocate the signals to the front
left and right speakers by changing the setting item “LFE/Bass
Out” to FRONT on the SOUND menu.
Use the control on the subwoofer to adjust its volume level. You
can also adjust the volume level using this unit’s remote control
(see page 36).
AM ANT FM ANT
75
UNBAL
OPTICAL
DVD
/CD
DTV
/CBL
VIDEO 1
SUBWOOFER
FRONT
R
SURR BACKCENTER SURROUND
123
COAXIAL
GND
TUNER
EXT. IN/OUT
OUTPUT
TV IN/OUT
SPEAKERS
MAINS
DIGITAL
INPUT
L R L
+
+
71 2 4365
The surround back speaker outputs the surround back channel included in Dolby Digital EX and DTS-ES software and only
operates when the Dolby Digital EX or DTS-ES decoder is turned on.
Center
speaker
Front
speakers
Surround
speakers
Surround back
speaker
Subwoofer
system
Right LeftRight Left
Notes
7
1
2
6
5
4
3
Speaker layout
01EN.00_RX-SL100RDS.book Page 11 Thursday, November 27, 2003 12:42 PM
CONNECTIONS
12
Do not connect this unit or other components to the mains power until all connections between components are complete.
Make sure that all connections are made correctly - that is to say, L (left) to L, R (right) to R, “+” to “+” and “–”
to “–”. Some components require different connection methods and have different jack names. Refer to the operating
instructions for each component you wish to connect to this unit.
After you have completed all connections, check them again to make sure they are correct.
The jack names correspond to the names on the input selector.
Connecting a TV
Connect one end of the SCART cable to the TV/IN OUT connector on this unit and the other end to the SCART
connector on your TV.
Connecting AV components
Connect one end of the SCART cable to the EXT. IN/OUT connector on this unit and the other end to the SCART
connector on your AV component. You can also daisy chain several SCART components together as shown in “Digital
audio connections” (page 13).
Use a SCART cable to make the above connections. The SCART cable, or “Euro AV cable”, supports IN/OUT signal transmission,
providing you with the best possible picture and sound.
CONNECTIONS
Before connecting components
Connecting other components
Note
CAUTION
AM ANT FM ANT
75
UNBAL
OPTICAL
DVD
/CD
DTV
/CBL
VIDEO 1
SUBWOOFER
FRONT
R
SURR BACKCENTER SURROUND
123
COAXIAL
GND
TUNER
EXT. IN/OUT
OUTPUT
TV IN/OUT
SPEAKERS
MAINS
DIGITAL
INPUT
L R L
+
+
AV component
(DVD player, cable tuner, etc.)
TV
01EN.00_RX-SL100RDS.book Page 12 Thursday, November 27, 2003 12:42 PM
13
English
CONNECTIONS
PREPARATION
Digital audio connections
Connect the optical or coaxial digital output on your components to the corresponding DIGITAL INPUT jacks.
Use OPTICAL 1 (DVD/CD) to connect a DVD or CD player.
Use OPTICAL 2 (DTV/CBL) to connect a DTV or cable tuners.
y
You can assign components to this unit’s DIGITAL INPUT jacks using the INPUT and VOLUME/SELECT controls on the front panel
(or the input selector buttons on the remote control) (page 43).
The OPTICAL jacks on this unit conform to the EIA standard. If you use a fiber optic cable that does not conform to this standard, this
unit may not function properly.
You may experience some image distortion if your VCR is connected to this unit through your DVD player rather than being directly
connected to this unit.
VIDEO 2 jacks (on the front panel)
Use these jacks to connect any video source, such as a game console or video camera, to this unit.
Notes
Optical out
Optical out
SCART
SCART
SCART
RX-SL100RDS
DTV or
Cable tuner
DVD player
VIDEO AUDIO
VIDEO 2
OPTICALL R
O
V
L
R
Game console
or video
camera
Video out
Audio out L
Audio out R
Optical out
01EN.00_RX-SL100RDS.book Page 13 Thursday, November 27, 2003 12:42 PM
14
CONNECTIONS
Both AM and FM indoor antennas are included with this
unit. In general, these antennas should provide sufficient
signal strength. Connect each antenna correctly to the
designated terminals.
Connecting the AM loop antenna
1 Set up the AM loop antenna, then connect it
to the terminals on this unit.
2 Press and hold the tab to insert the white
cord into the AM ANT terminal and the black
cord into the GND terminal.
3 Orient the AM loop antenna for the best
reception.
The AM loop antenna should be placed away from this unit and
all speaker cords.
The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality, an
outdoor antenna may improve the quality. Consult the nearest
authorized YAMAHA dealer or service center about outdoor
antennas.
Frequency Step (Asia and General
models only)
Because the interstation frequency spacing differs in
different areas, set the FREQUENCY STEP (using the on-
screen display operations) according to the frequency
spacing in your area (see page 45).
North, Central and South America: 100 kHz/10 kHz
Other areas: 50 kHz/9 kHz
Connecting the antennas
AM ANT FM ANT
75 UNBAL
GND
TUNER
AM loop antenna
(included)
Ground (GND terminal)
For minimum interference, connect the
antenna
GND terminal to a good earth
ground. A good earth ground is a metal
stake driven into moist earth.
Indoor FM antenna
(included)
Black
W h i t e
Notes
01EN.00_RX-SL100RDS.book Page 14 Thursday, November 27, 2003 12:42 PM
15
English
CONNECTIONS
PREPARATION
Connecting the AC power
After all other connections are complete, plug the power
cord to an AC wall outlet.
Memory back-up
The memory back-up circuit prevents the stored data from
being lost even if this unit is in the standby mode.
However if the power cord is disconnected from the AC
wall outlet, or the power supply is cut for more than one
week, the stored data will be lost.
When all connections are complete, turn on the power of
this unit.
1 Press STANDBY/ON on the front panel or
remote control to turn on the power of this
unit.
The level of the main volume, and then the current
sound field program name appear on the front panel
display.
2 Turn on the video monitor connected to this
unit.
Connecting the power Turning on the power
INPUT
VOLUME/SELECT
DSPTUNER
AUTO/MA N'L
PUSH-ENTER
STANDBY
/ON
PHONES VIDEO AUDIO
VIDEO 2
SILENT
OPTICALL R
1
1
HALL
2
JAZZ
3
ROCK
4
ENTERTAIN
SLEEP
STANDBY/ON
5
MUSIC
6
TV THTR
7
MOVIE 1
8
MOVIE 2
9
TV AV
CODE SET
REC
s
FREQ/RDS
AUDIO
EON
DISC SKIP
MODE
PTY SEEK
START
q/DTS
0
NIGHT
+10
EX/ES
ENT
STEREO
EFFECT
1
or
STANDBY
/ON
STANDBY/ON
or
Front panel
Remote control
01EN.00_RX-SL100RDS.book Page 15 Thursday, November 27, 2003 12:42 PM
BASIC SETUP
16
The BASIC setup feature is a useful way to setup your
system quickly and with minimal effort. The BASIC setup
items are displayed on both the front panel of this unit and
your video monitor. By using the GUI (on your video
monitor), you can easily make any necessary settings.
y
In addition to using the BASIC menu, you can use the detailed
parameters in the SOUND menu (page 40) to manually
configure this unit using more precise adjustments.
Altering any parameters in the BASIC menu will reset
parameters in the SOUND menu.
The explanations in this document are based on the GUI. The
characters shown in the front panel display may differ from
those on the GUI.
Speaker Set Up
1 Switch on the receiver and video monitor.
Make sure the OSD is displayed on your video
monitor.
2 Press AMP.
3 Press SET MENU.
The top display appears on your video monitor.
4 Press k/n repeatedly to select BASIC menu,
then press h.
5 Press k/n repeatedly to select Speaker Set
Up, then press h.
BASIC SETUP
Using BASIC setup
b
TITLE
LEVEL
ENTER
CH
CH
+
p
MUTE
TV VOL VOLUME
AMP
VCRDVD/CD VIDEO 1
TUNERDTV/CBL VIDEO 2
a
MUTE INPUT
CH
TV MODE
+
RX-SL100RDS
MENU
SET MENU
RETURN
TEST
DISPLAY
3
4-10
2
AMP
MENU
SET MENU
OPTION menu
BASIC menu Speaker Set Up
SOUND menu Speaker Level
INPUT menu
ENTER
ENTER
Speaker Set Up Room Size
Speaker Level Subwoofer Set
Speaker Num
01EN.00_RX-SL100RDS.book Page 16 Thursday, November 27, 2003 12:42 PM
17
English
BASIC SETUP
PREPARATION
6 Press k/n repeatedly to select Room Size,
then press ENTER.
Use k/n to select the size of the room you have
installed your speakers in, then press ENTER.
Roughly speaking, the room sizes are defined as
follows:
[U.S.A. and Canada models]
S (small) 16 x 13 ft, 200 sq. ft
(4.8 x 4.0 m, 20 m
2
)
M (medium) 20 x 16 ft, 300 sq. ft
(6.3 x 5.0 m, 30 m
2
)
L (large) 26 x 19 ft, 450 sq. ft
(7.9 x 5.8 m, 45 m
2
)
[Other models]
S (small) 3.6 x 2.8 m, 10 m
2
M (medium) 4.8 x 4.0 m, 20 m
2
L (large) 6.3 x 5.0 m, 30 m
2
7 Press k/n repeatedly to select Subwoofer
Set, then press ENTER.
Use k/n to select Yes or None, then press ENTER.
Yes If you have a subwoofer in your system.
None If you do not have a subwoofer in your system.
8 Press k/n repeatedly to select Speaker Num,
then press ENTER.
Use k/n to select the number of speakers connected
to the unit, then press ENTER. The choices vary as
follows:
9 After you have finished the settings, press n
repeatedly to select Setting OK?, then press
ENTER.
Use k/n to select Set or Cancel, then press ENTER.
Set To apply the changes and start the test
tone.
Cancel To cancel the changes and return to
Speaker Set Up.
Use the test tone to check the speaker levels.
If you selected Set, the display changes to “CHECK:
Test Tone”, and the unit outputs a test tone from each
speaker in turn. When the test tone begins, the display
changes to “CHECK OK: YES”.
The unit cycles the test tone around each of the speakers in turn
twice.
The indicator of the speaker currently outputting the test tone
flashes on the front panel display.
10 Press k/n repeatedly to select Yes or No,
then press ENTER.
Yes To return to Speaker Set Up.
No To enter Speaker Level.
Speaker Level
Use this menu to compare and adjust the test tone output
from each speaker to the output from the left front (or left
surround) speaker so that the volume level for all speakers
is identical.
Press ENTER to enter the Speaker Level
adjustment menu, then press k/n to select a
speaker and adjust the balance using l / h.
The unit outputs the test tone from the selected speaker
and the left front (or left surround) speaker in turn. The
indicator of the speaker currently outputting the test tone
flashes on the front panel display.
Choices Display Speakers
2 spk
Front L/R
3 spk
Front L/R, Center
4 spk
Front L/R, Surround L/R
5 spk
Front L/R, Center, Surround L/R
6 spk
Front L/R, Center, Surround L/R,
Surround back
LL C R
SL SB SR
LL CR
SL SB SR
LL C R
SL SB SR
LL C R
SL SB
SB
SR
LL C R
SL SB SR
Notes
Front
Speaker Set Up Center
Speaker Level Sur L
Sur R
Sur Back
01EN.00_RX-SL100RDS.book Page 17 Thursday, November 27, 2003 12:42 PM
18
BASIC SETUP
Front Adjusts the balance between the front left and right
speakers.
Center Adjusts the balance between the front left and
center speakers.
Sur L Adjusts the balance between the front left and
surround left speakers.
Sur R Adjusts the balance between the surround left and
surround right speakers.
Sur Back Adjusts the balance between the surround left
and surround back speakers.
Subwoofer Adjusts the balance between the front left
speaker and the subwoofer.
y
You can also make test tone setting adjustments by pressing
TEST on the remote control.
Memory back-up
The memory back-up circuit prevents the stored data
from being lost even if this unit is in the standby mode.
However, if the power cord is disconnected from the
AC outlet, or the power supply is cut for more than one
week, the stored data will be lost. If so, adjust the
items again.
01EN.00_RX-SL100RDS.book Page 18 Thursday, November 27, 2003 12:42 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374
  • Page 375 375
  • Page 376 376
  • Page 377 377
  • Page 378 378
  • Page 379 379
  • Page 380 380
  • Page 381 381
  • Page 382 382
  • Page 383 383
  • Page 384 384
  • Page 385 385
  • Page 386 386
  • Page 387 387
  • Page 388 388
  • Page 389 389
  • Page 390 390
  • Page 391 391
  • Page 392 392
  • Page 393 393
  • Page 394 394
  • Page 395 395
  • Page 396 396
  • Page 397 397
  • Page 398 398
  • Page 399 399
  • Page 400 400
  • Page 401 401
  • Page 402 402
  • Page 403 403
  • Page 404 404
  • Page 405 405
  • Page 406 406
  • Page 407 407
  • Page 408 408
  • Page 409 409
  • Page 410 410
  • Page 411 411
  • Page 412 412
  • Page 413 413
  • Page 414 414
  • Page 415 415
  • Page 416 416

Yamaha RX-SL100 El kitabı

Kategori
AV alıcıları
Tip
El kitabı