DeWalt DW03050 Kullanım kılavuzu

Please read these instructions before operating the product.

DW03050, DW03101

User Manual

GB

NL

GR

I

FIN

D

DK

ES

NO

F

SE

PT

TR

www.2helpU.com

2

1

2

0.000 m

50.0°

B

D

AAA

A

4

DW0165SI

4.5V DC

2

5

6

1

3

7

8

C

3

1

2

4

5

6

0.0000 m

50.0°

0.0000 m

50.0°

=

ft/m

4

H

J

K

0.0000 m

0.7000m

50.0°

I

71.77 in

45.86 in

50.0°

max

min

+

0.3000 m

0.7000 m

1.0000m

50.0°

+

-

/

0.8500m

-

50.0°

0.1500 m

1.0000 m

+

-

/

5

L

0.6000 m

0.4000 m

0.2400 m

50.0°

2

M

N

O

0.7000 m

0.6000 m

0.5000 m

0.2100 m

50.0°

3

2

0.240 m

2

+

0.210 m

0.450 m

2

50.0°

+

-

/

+/-

6

1.0100m

2.7390 m

50.0°

2.1000 m

?

P

Q

?

R

7

4.8270m

24.3°

0.0320 m

24.3°

?

S

T

8

12”

0.000 in

0.00 in

12.0 in

50.0°

a

12”

0.000 in

12.0 in

50.0°

a

12” 12”

0.000 in

12.0 in

50.0°

a

12”

U

9

180°

90°

180°

X

15.0°

50.0°

V

?

W

10

GB

Contents

• User Safety

• Battery Safety

• Setup (Load Batteries)

• Operation

• Warranty

• Error Codes

• Specications

Retain all sections of this manual for future

reference.

User Safety

WARNING:

Carefully read the Safety Instructions and

Product Manual before using this product.

The person responsible for the product must

ensure that all users understand and adhere to

these instructions.

WARNING:

The following label information is placed on

your laser tool to inform you of the laser class

for your convenience and safety.

DW03101

4.5V DC

DW03050

4.5V DC

The DW03050 and DW03101 tools emit a visible laser

beam, as shown in Figure

A

1

). The laser beam

emitted is Laser Class 2 per IEC 60825-1 and complies

with 21 CFR 1040.10 and 1040.11 except for deviations

pursuant to Laser Notice No. 50, dated June 24, 2007.

WARNING:

While the laser tool is in operation, be careful

not to expose your eyes to the emitting laser

beam (red light source). Exposure to a laser

beam for an extended time period may be

hazardous to your eyes. Do not look into the

beam with optical aids.

WARNING: To reduce the risk of injury, user

must read the Product User manual, Laser

Safety manual, and Battery Safety information.

EC-Declaration of Conformity

Radio Equipment Directive

DEWALT Laser Distance Measurer

DW03050 and DW03101

DEWALT hereby declares that the DEWALT Laser

Distance Measurer DW03050/DW03101 is in

compliance with the Directive 2014/53/EU and to all

applicable EU directive requirements.

The full text of the EU Declaration of Conformity can

be requested at D

EWALT Industrial Tool Co., DEWALT

Europe, DEWALT D-655-10 Idstein, Germany 65509

or is available at the following internet address:

www.2helpU.com.

Search by the Product and Type Number indicated on

the nameplate.

Battery Safety

WARNING: Batteries can explode or leak and

cause serious injury or re. To reduce the risk:

ALWAYS follow all instructions and warnings

on the battery label and package.

DO NOT short any battery terminals.

DO NOT charge alkaline batteries.

DO NOT mix old and new batteries. Replace

all of them at the same time with new batteries

of the same brand and type.

DO NOT mix battery chemistries.

DO NOT dispose of batteries in re.

ALWAYS keep batteries out of reach of

children.

ALWAYS remove batteries if the device will not

be used for several months.

NOTE: Ensure that the recommended

batteries are used.

NOTE: Ensure the batteries are inserted in the

correct manner, with the correct polarity.

11

GB

Loading Batteries

1.

Pull up the endpiece on the back of the tool (Figure

D

1

).

2.

Pull up the battery compartment latch on the back of

the tool (Figure

D

2

and

D

3

).

3.

Insert three AAA batteries, making sure to position

the - and + ends of each battery as noted inside the

battery compartment (Figure

D

4

).

4.

Push the battery door down until it snaps in place

(Figure

D

5

).

When the tool is ON, the battery level appears on the

screen (Figure

C

1

).

Turning the Tool On

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

Choosing the Settings

Setting Automatic Turn Off

By default, the tool will automatically turn off 90 seconds

after no buttons or options have been selected. To

change when the tool automatically turns off, follow

these steps.

1.

On the first screen (Figure

E

1

), press to

display the Main Menu.

2.

On the Main Menu (Figure

E

2

), select and

press

.

3.

On the Settings Menu (Figure

G

), select and

press

.

4.

Select the time.

• Choose to turn off the tool after 30 sec, 60 secs,

90 secs, or 300 secs.

• To keep the tool turned on until you manually

turn it off (by pressing and holding

for

10 seconds), select

∞

.

5.

Press to save your setting.

Setting Screen Brightness

By default, the tool's screen will be set at 25%

brightness. To change the brightness level, follow

these steps.

1.

On the first screen (Figure

E

1

), press to

display the Main Menu.

2.

On the Main Menu (Figure

E

2

), select and

press

.

3.

On the Settings Menu (Figure

G

), select and

press

.

4.

Select the desired brightness level: 25%, 50%, 75%,

or 100%.

5.

Press to save your new setting.

Turning Off the Sound

By default, the tool will beep each time you take a

measurement. You can turn off the beeps.

1.

On the first screen (Figure

E

1

), press to

display the Main Menu.

2.

On the Main Menu (Figure

E

2

), select and

press

.

3.

On the Settings Menu (Figure

G

), select and

press

to display .

4.

Press to save your setting.

Changing the Unit of Measure

ft/m

By default, the tool will display measurements in meters

(1.8940 m). You can change the unit of measure to

fractional ft (6'02"

9/16), inches (74 9/16 in), decimal ft

(6.21 ft), or decimal inches (3.21 in).

1.

On the first screen (Figure

E

1

), press to

display the Main Menu.

2.

On the Main Menu (Figure

E

2

), select and

press

.

3.

On the Settings Menu (Figure

G

), select ft/m and

press

.

12

GB

4.

Select the unit of measure.

• 0'00" 0/00

• 0" 0/00

• 0'00" ft

• 0.00 in

• 0.0000 m

5.

Press to save your setting.

Choosing the Tool Position

By default, distances are measured from the bottom of

the tool to a wall or object (Figure

F

3

). To measure

distances from a different tool location, follow these steps.

1.

On the first screen (Figure

E

1

), press to

display the Main Menu.

2.

On the Main Menu (Figure

E

2

), select and

press

.

3.

Select the tool position.

• To measure from the top of the tool (Figure

F

1

), select .

• To measure from the tripod connection on the

tool (Figure

F

2

), select .

• To measure from a corner or another hard-to-reach

location with the endpiece flipped open (Figure

D

1

), select (Figure

F

4

) to measure from the

end of the endpiece.

4.

Press to save your new setting.

Taking Measurements

Measuring Distance

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Point the tool's laser (Figure

A

1

) toward the

wall or object whose distance you need to measure

(Figure

H

1

).

5.

Press to measure the distance from the tool to

the wall or object.

6.

At the bottom of the screen, view the current

measurement (Figure

H

2

).

To take a new measurement, press

to move

the current measurement up to the previous line on the

screen. Then repeat steps 4-6.

Adding 2 Measurements

You can add two measurements to get a total

measurement of the two distances (Figure

I

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

)

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Press to indicate that you want to add two

measurements.

6.

Point the tool's laser toward the wall or object whose

distance you need to measure (Figure

I

1

).

7.

Press to measure the distance from the tool to

the first wall or object.

8.

Point the tool's laser toward the next wall or object

(Figure

I

2

).

9.

Press to measure the distance and add it to

the previous measurement.

10.

View the total of the two measurements at the bottom

of the screen (Figure

I

3

).

13

GB

Subtracting 2 Measurements

You can subtract one measurement from another

(Figure

J

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Press to indicate that you want to subtract one

measurement from another.

6.

Point the tool's laser toward the wall or object whose

distance you need to measure (Figure

J

1

).

7.

Press to measure the distance from the tool to

the wall or object.

8.

Point the tool's laser toward the wall or object

whose distance is to be subtracted from the first

measurement (Figure

J

2

).

9.

Press to measure the distance and subtract it

from the previous measurement.

10.

View the difference between the two measurements

at the bottom of the screen (Figure

J

3

).

Measuring Continuously

To take a series of measurements as you move around,

change to Continuous Measure mode (Figure

K

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Point the tool's laser (Figure

A

1

) toward the

wall or object whose distance you need to measure

(Figure

K

1

).

6.

At the bottom of the screen, view the current

measurement (Figure

K

2

), which will keep

changing as you move the tool.

7.

To take the current measurement (from the tool to the

wall or object) and exit Continuous Measure mode,

press

.

To take a new measurement, press

to move

the current measurement up to the previous line on the

screen. Then repeat steps 4-7.

Measuring Area

You can measure the area of a wall, floor, or object

(Figure

L

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

14

GB

5.

Measure the width (Figure

L

1

).

• Point the top of the tool at one side of the wall,

floor, or object.

• Position the tool at one end of the wall, floor, or

object and point the laser dot across the width.

(Figure

L

1

shows where to position the tool if

you are measuring from the bottom of the tool.)

• Press

to display the width measurement at

the top of the screen.

6.

Measure the length (Figure

L

2

).

• Position the tool at one end of the wall, floor, or

object and point the laser dot across the length.

(Figure

L

2

shows where to position the tool if

you are measuring from the bottom of the tool.)

• Press

to display the length measurement on

the second line of the screen.

7.

View the Area measurement at the bottom of the

screen (Figure

L

3

).

Adding/Subtracting 2 Areas

You can measure the area of a wall, floor, or object

and then add it to, or subtract it from, the area of

another wall, floor, or object (Figure

M

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu

(Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Press to add, or to subtract, the areas of two

walls, floors, or objects.

6.

Measure the width of the first wall, floor, or object

(Figure

M

1

).

• Position the tool at one end of the wall, floor, or

object and point the laser dot across the width.

(Figure

M

1

shows where to position the tool if

you are measuring from the bottom of the tool.)

• Press

to display the width measurement at

the top of the screen.

7.

Measure the length of the first wall, floor, or object

(Figure

M

2

).

• Position the tool at one end of the wall, floor, or

object and point the laser dot across the length.

(Figure

M

2

shows where to position the tool if

you are measuring from the bottom of the tool.)

• Press

to display the length measurement on

the second line of the screen.

8.

Follow the same steps to measure the width and

length of the second wall, floor, or object.

9.

View the Area measurement at the bottom of the

screen (Figure

M

3

).

Measuring Volume

You can measure the volume of a room or object

(Figure

N

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

15

GB

5.

Measure the width (Figure

N

1

).

• Point the top of the tool at one side of the room

or object.

• Position the tool at one end of the room or object

and point the laser dot across the width. (Figure

N

1

shows where to position the tool if you are

measuring from the bottom of the tool.)

• Press

to display the width measurement at

the top of the screen.

6.

Measure the length (Figure

N

2

).

• Position the tool at one end of the room or object

and point the laser dot across the length. (Figure

N

2

shows where to position the tool if you are

measuring from the bottom of the tool.)

• Press

to display the length measurement on

the second line of the screen.

7

Measure the height (Figure

N

3

).

• Position the tool at one end of the room or object

and point the laser dot across the height. (Figure

N

3

shows where to position the tool if you are

measuring from the bottom of the tool).

• Press

to display the height measurement on

the third line of the screen.

8.

View the Volume measurement at the bottom of the

screen (Figure

N

4

).

Adding/Subtracting 2 Volumes

You can measure the volume of room or object

and then add it to, or subtract it from, the volume of

another room or object (Figure

O

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Press to add, or to subtract, the volumes of

two rooms or objects.

6.

Measure the width (Figure

O

1

).

• Position the tool at one end of the room or object

and point the laser dot across the width. (Figure

O

1

shows where to position the tool if you are

measuring from the bottom of the tool.)

• Press

to display the width measurement at

the top of the screen.

7.

Measure the length (Figure

O

2

).

• Position the tool at one end of the room or object

and point the laser dot across the length. (Figure

O

2

shows where to position the tool if you are

measuring from the bottom of the tool.)

• Press

to display the length measurement on

the second line of the screen.

8.

Measure the height (Figure

O

3

).

• Position the tool at one end of the room or object

and point the laser dot across the height. (Figure

O

3

shows where to position the tool if you are

measuring from the bottom of the tool).

• Press

to display the height measurement on

the third line of the screen.

9.

Follow the same steps to measure the width, length,

and height of the second room or object.

10.

View the Volume measurement at the bottom of the

screen (Figure

O

4

).

16

GB

Measuring the Height of a Tall Object

If you need to measure the height of a tall object (e.g.,

a tall building), you can calculate the height based

on the distance to 1 point or the distances from the

same point to 2 points on the object. The tool will

use the Pythagorean Theorem (C

2

=A

2

+B

2

) to calculate

the height.

Distance to 1 Point

You can use the distance to one point on a wall

or object (Indirect Height) to determine its height

(Figure

P

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Position the tool opposite the bottom of the vertical

height to be measured (Figure

P

1

).

6.

Point the laser toward the highest point of the

building or object whose height you need to

measure (Figure

P

1

).

7.

Press to measure the distance.

8

View the height measurement at the bottom of the

screen (Figure

P

2

).

Distances to 2 Points

You can use the distance to two points on a wall or

object (Double Indirect Height) to determine its height

(Figure

Q

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Position the tool opposite the approximate center of

the vertical height to be measured (Figure

Q

1

).

6.

Point the laser toward the lowest point of the

building or object whose height you need to

measure (Figure

Q

2

).

7.

Press to measure the distance.

8.

From the same point, aim the laser at the highest

point of the building or object (Figure

Q

3

).

9.

Press to measure the distance.

10.

On the bottom line of the screen, view the height of

the building or object (Figure

Q

4

).

Measuring Partial Height

If you need to determine the height of a section of a

wall or object (e.g., the distance from the ceiling to the

top of TV or window on the wall) (Figure

R

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

17

GB

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Point the laser at the highest point of the wall or

object (Figure

R

1

).

6.

Press to measure the distance to the top of

the tall object.

7.

From the same point, aim the laser at the top of

the obstruction on the wall or object (Figure

R

2

).

8.

Press to measure the distance from the top

of the wall to the obstruction (TV, window, etc.).

9.

From the same point, aim the laser on a horizontal

line straight ahead toward the bottom of the wall

(Figure

R

3

).

10.

Press to measure the distance.

11.

On the bottom line of the screen, view the distance

between the top of the wall and the top of the

obstruction on the wall (Figure

R

4

).

Measuring Height of Obstructed Object

Follow these steps to determine the height of a tall

building or object that is blocked by other buildings or

objects (Figure

S

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

(Figure

E

4

).

• Press

.

5.

Point the laser at the highest point of the building,

wall, or object (Figure

S

1

).

6.

Press to take the measurement.

7.

On the bottom line of the screen, view the height of

the building or object (Figure

S

2

).

Measuring from a Tripod

If you are placing the tool on a tripod to measure the

height of a tall building, follow these steps (Figure

T

).

1.

Screw the 1/4-20" hole on the back of the tool onto

the 1/4-20" connection on the top of your tripod

(Figure

T

1

).

2.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

3.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

4.

Make sure the tool position setting (Figure

C

4

) is

to measure from the tripod connection.

5.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

(Figure

E

4

).

• Press

.

6.

Point the laser at the lowest point of the wall or object

whose height you need to measure (Figure

T

2

).

7.

Press to take the measurement.

18

GB

8.

Point the laser at other points on the wall or object

(Figure

T

3

).

9.

When ready, press to take the measurement.

10.

On the bottom line of the screen, view the height of

the wall or object (Figure

T

4

).

Positioning Studs

a

When you are framing a wall, use the Stakeout feature

to easily mark the position of each stud (Figure

U

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

set to to measure from the back of the tool.

4.

Select

a

as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

a

(Figure

E

4

).

• Press

.

5.

Determine the distance between each stud, for

example, 12".

6.

Press and until the top number on the screen

is set to the distance from the right edge of one stud

to the left edge of the next (e.g., 12") (Figure

U

1

).

7.

Line up the back of the tool with the right edge of the

last stud that is nailed in (Figure

U

2

).

8.

Press to start measuring the distance as you

slowly move the tool to the right.

9.

Continue moving the tool to the right until the bottom

number on the screen is 0.00 in (Figure

U

3

).

10.

Press to stop measuring.

11.

Using a pencil, mark the location where the left edge

of the stud should be nailed into the wall frame.

12.

Nail the left edge of the stud at the marked location.

13.

For each remaining stud in the wall frame, repeat

steps 7-12 (Figure

U

4

).

Measuring an Angle

If you need to determine the angle at which something

is positioned, use the tool to measure that angle

(Figure

W

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Make sure the tool position setting (Figure

C

4

) is

correct for taking the measurement.

4.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

5.

Position the tool at the angle to be measured (Figure

W

1

).

6.

Press to take the measurement.

7.

View the angle measurement on the screen (Figure

W

2

).

Using the Tool as a Level

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

19

GB

3.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

.

• Press

.

4.

Place the tool in the vertical or horizontal position on

the surface that you want to check is level (Figure

V

1

).

5.

On the tool's screen, view the position of the white

bubble on the vial (Figure

V

2

).

Using the Tool With

You can use the tool's Bluetooth

®

capability to pair it with

the DEWALT

®

Tool Connect™ application on your cell

phone or tablet, and then mark up room photos with the

measurements you have taken.

1.

From either or , download the

DEWALT

®

Tool Connect™ application to your cell

phone or tablet.

2.

Using the DEWALT

®

Tool Connect™ application,

capture the room or space for which you want to

record the measurements, by taking room photos.

3.

On the DW03050 or DW03101 keypad, press

to turn on the tool.

4.

If appears on the screen (Figure

C

2

), turn on

the Bluetooth

®

connection.

• On the keypad, press

to display the main

menu.

• Select

.

• Press

to turn on the Bluetooth

®

connection.

5.

Use the DEWALT

®

Tool Connect™ application

to pair your cell phone or tablet to the DW03050

or DW03101, and then mark up photos with the

measurements you have taken.

THE BLUETOOTH® WORD MARK AND LOGOS ARE

REGISTERED TRADEMARKS OWNED BY BLUETOOTH SIG,

INC. AND ANY USE OF SUCH MARKS BY DEWALT IS UNDER

LICENSE. APPLE AND THE APPLE LOGO ARE TRADEMARKS

OF APPLE INC., REGISTERED IN THE U.S. AND OTHER

COUNTRIES. APP STORE IS A SERVICE MARK OF APPLE

INC., REGISTERED IN THE U.S. AND OTHER COUNTRIES.

GOOGLE PLAY AND THE GOOGLE PLAY LOGO ARE TRADE-

MARKS OF GOOGLE INC.

Viewing the Tool's Memory

Up to the last 20 measurements are stored in the tool's

memory.

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

(Figure

E

4

).

• Press

.

4.

View the last measurement that was taken. Press

to scroll through all the measurements that have

been stored in the tool's memory (up to 20). Press

to scroll back.

Clearing the Tool's Memory

You can clear one or more measurements that are

currently in the tool's memory.

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

20

GB

3.

Select as the measurement type.

• Press

to display the Main Menu (Figure

E

2

).

• Press

to select .

• Press

to display the Measurement Type

Menu (Figure

E

3

).

• Press the arrow buttons to select

(Figure

E

4

).

• Press

.

4.

Specify which measurement you want to delete:

• To delete a specific measurement, continue with

step 5.

• To delete ALL measurements, skip to step 6.

5.

To delete a specific measurement:

• Press

or to scroll through the

measurements that have been stored in the

tool's memory (up to 20) until you display the

measurement to be deleted.

• Press

.

• Select

and press to delete the

measurement.

6.

To delete ALL measurements:

• Press

.

• Select

and press to delete all

measurements from the tool's memory.

Turning Off the Tool

The tool can be turned off in either of these ways:

• Press and hold

for 10 seconds. When you

release

after 10 seconds, the tool will turn off.

• If you do not use the tool for 90 seconds, it will

automatically turn off.

Calibrating the tool

Please note that if you do not position the tool correctly for

each step of the calibration process,

will appear in red

on the screen (Figure

X

).

1.

Point the tool's laser (Figure

A

1

) toward a wall or

object, and not toward anyone's eyes.

2.

Press (Figure

A

3

) to turn the tool on and

display the red laser dot.

3.

Press to display the Main Menu (Figure

E

2

).

4.

On the Main Menu, select and press .

5.

On the Settings Menu (Figure

G

), select and

press

.

6.

Place the tool with the screen facing upward on a flat,

level surface (Figure

X

1

).

7.

Press .

8.

While the tool is still laying on the level surface, turn

the tool 180° (Figure

X

2

).

9.

Press .

10.

Flip the long side of the tool 90° so it is laying on its

side (Figure

X

3

).

11.

Press .

12.

While the tool is still laying on its side, turn the tool

180° (Figure

X

4

).

13.

Press .

14.

Make sure appears on the tool's screen (Figure

X

5

).

Sayfa yükleniyor ...

DeWalt DW03050 Kullanım kılavuzu

DeWalt DW03050 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler

Diğer Belgeler