Whirlpool AKR 468 IX El kitabı
- Kategori
- Ocak davlumbazları
- Tip
- El kitabı
Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
5019 318 33304
MONTAJ BİLGİ SAYFASI
Ocak üzerindeki kap destek yüzeyleri ve ocak davlumbazının en alt kısmı arasındaki mesafe
elektrikli ocaklar için 50 cm ve gazlı veya ikisi bir arada ocaklar için 65 cm altında
OLMAMALIDIR.
Gazlı ocakların montaj talimatlarında daha fazla mesafe bırakılması isteniyorsa, bu mesafeye
uyulmalıdır. Montaj için yetkili bir teknisyene başvurun. Cihazı monte ederken
numaralandırılmış adımları takip edin (1Ö2Ö3Ö.....).
Montaj işlemi tamamlanmadan, fişi prize takmayın.
UYARI: Boşaltım borusu ve kelepçelerin donanımla birlikte temin edilip edilmediğini kontrol
ediniz. Eğer temin edilmemişse, ayrıca satın alınmalıdırlar.
Not: Özel olarak “(*)” sembolü ile işaretli olan parçalar sadece bazı modellerde bulunan veya
bulunmayan modellerde ayrıca satın alınabilen opsiyonel aksesuarlard
ır.
Ürün çok ağırdır; davlumbazın taşınma ve montajı en az iki kişi tarafından yapılmalıdır.
INSTALLATION DATA SHEET
The minimum distance between the support surface of the recipients on the cooking device and the
lowest part of the hood MUST NOT BE less than 50 cm in the case of electric cookers and 65 cm for
gas or combination cookers.
If the installation instructions for a gas cooker specify a greater distance, then this distance must be
observed. It is advisable to contact a qualified technician for installation. To install, follow steps
(1Ö2Ö3Ö.....). Do not connect the hood to the electrical power supply until installation is completed.
WARNING: Check whether the exhaust pipe and clamps are provided. If not, they must be
purchased separately.
Note: Parts marked with the symbol “(*)” are optional accessories supplied only with some models
or parts not supplied, to be purchased separately.
Very heavy product; hood handling and installation must be carried out by at least two persons.
TR
GB
5019 318 33304
?
5019 318 33304
5019 318 33304
SAFEGUARDING THE ENVIRONMENT
1. Packing
Packing materials are 100% recyclable and are marked with the
recycling symbol .Comply with the local regulations for
disposal. The packing materials (plastic bags, polystyrene, etc.)
are a potential source of danger and must be kept out of the
reach of children.
2. Product
This appliance is marked in compliance with European Directive
2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is correctly scrapped, the user can
help prevent potentially harmful consequences for the
environment and the health of people.
The symbol on the product or the accompanying
documentation indicates that this product should not be treated
as domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic equipment.
Disposal must be carried out in compliance with local regulations
on waste disposal.
For further information on the treatment, recovery and recycling
of this product, contact the competent local office, the
household waste collection service or the shop where you
purchased the appliance.
IMPORTANT INSTRUCTIONS FOR
SAFETY
WARNING: To reduce the risk of accidents, electric shock,
injury or damage, when using the hood comply with the basic
precautions, including the following.
1. Always disconnect the hood from the power supply before
carrying out any installation or maintenance operation on the
appliance.
2. Installation must be carried out by a specialised technician, in
compliance with the manufacturer’s instructions and local
safety regulations.
3. Earthing of the appliance is compulsory. (Not possible for
Class II hoods).
4. Never use multisockets and extension leads.
5. The electrical components must no longer be accessible to
the user after installation.
6. Do not touch the hood with wet parts of the body or use it
when barefoot.
7. Do not pull the appliance power cable to unplug it.
8. After-sales service – do not repair or replace any part of the
hood unless specifically indicated in the manual. All other
maintenance services must be carried out by a specialised
technician.
9. When drilling the wall, make sure not to damage the
electrical connections and/or pipes.
10. The ventilation ducts must always discharge to the outside.
11. The Manufacturer declines any liability for improper use or
incorrect setting of the controls.
12. The appliance is not intended for use by children or persons
with limited physical, sensory or mental abilities or without
experience and knowledge of it, unless they are under the
supervision of or instructed in its use by a person responsible
for their safety.
13. Keep children away.
14. To reduce the risk of fire, only use a metal inlet duct.
15. Children must be supervised so that they do not play with
the appliance.
16. The product must be disposed of in compliance with local
regulations on waste disposal.
17. For further information on the treatment, recovery and
recycling of this product, contact the competent local office,
the household waste collection service or the shop where
you purchased the appliance.
18. Regular cleaning and maintenance is essential for correct
hood operation and good performance. Frequently clean all
encrustations from dirty surfaces to prevent the
accumulation of grease. Regularly clean or replace filters.
19. Do not “flambé” food under the hood. Naked flames could
cause a fire.
20. The room must have adequate ventilation when the hood is
used at the same time as appliances operating on gas or
other fuels.
21. The discharge air must not be eliminated in a duct used to
remove fumes produced by appliances operating on gas or
other fuels, but must have a separate outlet. All the national
regulations on air discharge envisaged by art. 7.12.1 of CEI
EN 60335-2-31 must be observed.
22. If the hood is used together with other appliances operating
on gas or other fuels, the negative pressure in the room
must not exceed 4 Pa (4 x 10
-5
bar). Therefore, make sure
the room is adequately ventilated.
23. Do not leave pans unattended when frying, since the cooking
oil could catch fire.
24. Make sure the lamps are cold before touching them.
25. The hood is not a shelf, therefore do not overload or place
objects on it.
26. Do not use or leave the hood without its lamps correctly
installed - risk of electric shock.
27. Wear work gloves for all installation and maintenance
operations.
28. The product is not suitable for outdoor use.
29. The air sucked by the hood must not be eliminated through
the same flue of the heating system or other appliances using
gas or other fuels.
TR
GB
5019 318 33304
Electrical connection
The mains voltage must match that given on the rating plate
located inside the hood. If provided with a plug, connect the
hood to a socket complying with the current regulations and
located in an accessible area. If it does not have a plug (direct
connection to the power supply) or if the plug is not in an
accessible place, fit a suitable double-pole switch that ensures
complete disconnection from the power supply in category III
overvoltage conditions, complying with the installation rules.
WARNING: Before reconnecting the hood circuit to the
power supply and checking correct operation, always make sure
the power cable is correctly fitted and that it was NOT crushed
in its housing during installation. Make sure to have this operation
carried out by a specialised technician.
Cleaning the hood
WARNING! Failure to remove oil/grease (at least once a
month) could result in fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Before using the hood
Please read these instructions carefully and keep them for future
reference, in order to ensure best use of your hood.
The packing materials (plastic bags, polystyrene, etc.) are a
potential source of danger and must be kept out of the reach of
children.
Make sure the hood has not been damaged during transport.
Declaration of conformity
This product has been designed, manufactured and put on the
market in conformity with:
- safety objectives of the “Low Voltage” Directive 2006/95/EC
(which replaces 73/23/EEC as amended)
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
If the hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
If the hood is not extracting enough:
• Is the right speed selected?
• Do the filters need cleaning or replacing?
• Are the air outlets blocked?
If the lamp does not work:
• Does the lamp need replacing?
• Is the lamp correctly fitted?
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself (see
“Troubleshooting Guide”).
2. Switch the appliance off and then on again to check if the
problem has been eliminated.
3. If the problem persists, contact the After-Sales Service.
Specify:
• the type of fault,
• the product model given on the dataplate inside the hood,
visible on removing the grease filters,
• your full address,
• your telephone number and area code,
• the Service code (the number under the word SERVICE on
the dataplate inside the hood, behind the grease filter).
If any repairs are necessary, contact an authorised Service Centre
(to ensure the use of original spare parts and correct repair).
Failure to comply with these instructions can compromise the
safety and quality of the product.
TR
GB
5019 318 33304
EXTRACTOR OR FILTERING HOOD INSTALLATION
Remove the perimeter extraction panel (if relevant) and the grease filter/s.
Pre-assemble the steam deflector on the motor assembly (if relevant): (a.) fit the steam deflector to the rails of the motor
assembly, (b.) connect up the control panel and the lamps, (c.) secure with 6 screws 3.5 x 6.5.
1. Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood.
2. Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-line drawn on
the wall. The template’s bottom edge represents the bottom edge of the hood.
3. Place the mounting bracket over the drilling template so that it matches the outlined rectangle. Mark and drill the two
outside holes. Remove the drilling template. Insert two wall plugs in the holes and fix the hood mounting bracket in place
with two 5 x 45 mm screws.
4. Hook the hood to the bracket.
5. Adjust the distance between the hood and the wall.
6. Adjust the hood horizontally.
7. From inside the hood, mark a hole for the final fixing of the hood.
8. Remove the hood from the bracket.
9. Drill (Ø 8 mm).
10. Insert a wall plug.
11. Fit the flue support bracket G to the wall and against the ceiling the small slot on the support must match the line drawn on
the wall (step1). Drill 2 holes (Ø 8 mm) and insert 2 wall plugs.
12. Secure with 2 screws 5 x 45 mm.
13. Hang the hood on the bottom mounting bracket.
14. Fix the hood to the wall with a 5 x 45 mm screw (ABSOLUTELY NECESSARY!).
15. Connect an exhaust pipe to the to the collar B, the fumes must be ducted to the outside (extractor version) or towards the
deflector (filter version).
Fit the deflector F to the flue support bracket G with 2 screws 3.5 x 6.5.
16. Make all necessary electrical connections.
17. Apply the flues and fix them with two 2 screws 2.9 x 6.5 (17a) to the flue support G (17b).
18. Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the hood.
TR
GB
5019 318 33304
1. Control panel.
a. Light switch.
b. Extraction and minimum extraction speed ON/OFF
switch.
c. Medium extraction speed switch.
d. Maximum extraction speed switch.
2. Grease filters.
3. Halogen lamps.
4. Telescopic flue.
Grease filters:
Metal grease filters have an unlimited
life and should be washed once a month
either by hand or in a dishwasher at a
low temperature and with a short cycle.
Washing in a dishwasher can cause
grease filters to turn white, but this in
no way affects efficiency.
a. press the handle to remove the filter
b. remove it.
Wash the filter and leave it to dry, proceeding in reverse
order to refit it.
Replacing the halogen bulbs:
1. Disconnect the hood from the mains power supply.
WARNING: Wear gloves.
2. Use a small screwdriver to gently prise the lamp cover off
(at the points indicated in Figure).
3. Remove the burnt-out lamp and fit a new one.
WARNING: Replace using 20W max G4 halogen bulbs
only.
Close the lighting unit (snap-on).
Active carbon filter
(filter hoods only):
The carbon filter must be cleaned once a month in a
dishwasher at the highest temperature, using a normal
dishwasher detergent. Wash the filters on their own.
After washing, reactivate the carbon filter by drying it in the
oven at 100°C for 10 minutes.
Change the carbon filter every 3 years
Fitting the carbon filter:
1. Remove the grease filter.
2. Remove the filter holder by turning the knobs 90°.
3. Fit the carbon filter “i” in the filter holder “h”.
Reverse the above procedure to re-fit the filter holder and
grease filter.
abcd
1
2
3
3
4
a
b
TR
GB
-
1
-
2
-
3
-
4
-
5
-
6
-
7
Whirlpool AKR 468 IX El kitabı
- Kategori
- Ocak davlumbazları
- Tip
- El kitabı
- Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:
diğer dillerde
- English: Whirlpool AKR 468 IX Owner's manual