Simplicity 2691354-00 Kullanım kılavuzu

Not for

Reproduction

Part No.: 80012358EST

Revision: -

cs

bg

en

et

hr

lt

hu

lv

pl

ro

sk

ru

sl

tr

Operator’s Manual

Ръководство за оператора

Návod k obsluze

Használati útmutató

Vartotojo vadovas

Korisnički priručnik

Kasutusjuhend

Operatora rokasgrāmata

Instrukcja obsługi

Manual de utilizare

Руководство оператора

Návod na obsluhu

Uporabniški priročnik

Kullanma Kılavuzu

Not for

Reproduction

2

A

B

C

D

E

F

G

H

1

A

B

D

F

G

H

Q

R

I

J

L

N

O

P

C

E

K

M

2

A

B

C

A

3

A

5

A

6

A

C

B

4

Not for

Reproduction

3

en

A

7

A

8

A

9

A

B

10

A

11

A

12

A

B

C

D

E

13

A

B

14

Not for

Reproduction

4

A

15

A

16

A

B

17

A

18

A

B

C

19

A

B

20

Not for

Reproduction

5

en

A

B

C

21

A

24

A

B

22

F

B

E

C

D

G

A

25

A

B

23

Not for

Reproduction

6

D

A

B

C

E

A

26

A

29

A

27

A

30

B

A

28

A

31

Not for

Reproduction

7

en

A

C

D

E

F

B

32

A

B

C

33

Not for

Reproduction

8

Thank you for purchasing this quality-built Rear Engine

Rider. We’re pleased that you’ve placed your confidence in

the brand. When operated and maintained according to the

manuals, your product will provide many years of dependable

service.

The manuals contain safety information to make you aware of

the hazards and risks associated with the unit and how to

avoid them. This Rear Engine Rider was designed to be used

as described in operator’s manual and is not intended for any

other purpose. It is important that you read and understand

the instructions thoroughly before attempting to start or oper-

ate this equipment. Save these original instructions for future

reference.

This product requires final assembly before use. Refer to the

setup guide for instructions on final assembly procedures.

Follow the instructions completely.

Products Covered by This Manual

The following products are covered by this manual:

2691347-00, 2691348-00, 2691354-00

Manual Contents:

Operator Safety .................................................................8

Features and Controls .................................................. 13

Safety Interlock Systems Checks .................................. 14

Operation ......................................................................... 14

Maintenance .................................................................... 18

Troubleshooting .............................................................. 23

Specifications .................................................................. 24

The images in this document are representative, and are

meant to complement the instructional text they accompany.

Your unit may vary from the images displayed. LEFT and

RIGHT are as seen from the operator’s position.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates an action that could result in damage to

the product.

Rear Engine Rider Hazard Symbols

General Operator Safety Warning

Symbol Meaning Symbol Meaning

Safety informa-

tion about haz-

ards that can

result in personal

injury.

Read and under-

stand the opera-

tor’s manual

before operating

or servicing the

unit.

Thrown objects

hazard.

Amputation

hazard - rotating

blade. Keep feet

away.

Amputation haz-

ard - do not touch

moving parts.

Amputation

hazard - rotat-

ing blade. Keep

hands away.

Keep bystand-

ers and children

away.

Toxic fume haz-

ard.

Fire hazard. Explosion hazard.

Battery explosion

hazard.

Shock hazard.

Hot surface haz-

ard.

Explosion hazard.

Shock hazard. Kickback hazard.

Eye protection

recommended.

Ear protection

recommended for

extended use.

Not for

Reproduction

9

en

Symbol Meaning Symbol Meaning

Remove the key

before perform-

ing service.

Remove the

spark plug wire

before performing

service.

WARNING

This powerful cutting machine is capable of amputating

hands and feet and can throw objects that can cause

injury and damage! Failure to comply with the following

SAFETY instructions could result in serious injury or death

to the operator or other persons. The owner of the machine

must understand these instructions and must allow only

persons who understand these instructions to operate

machine. Each person operating the machine must be of

sound mind and body and must not be under the influence

of any substance, which might impair vision, dexterity or

judgment.

Carbon Monoxide Warning

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains

carbon monoxide, a poisonous gas that could kill

you in minutes. You CANNOT see it, smell it, or taste

it. Even if you do not smell exhaust fumes, you could

still be exposed to carbon monoxide gas. If you start

to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

• Operate this product ONLY outside far away from win-

dows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

Protection for Children

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the

machine and the mowing activity. Children who have been

given rides in the past may suddenly appear in the mowing

area for another ride and be run over or backed over by the

machine. Never assume that children will remain where you

last saw them.

1. KEEP children out of the mowing area and under the

watchful care of a responsible adult other than the opera-

tor.

2. DO NOT allow children in yard when machine is oper-

ated (even with the blade OFF).

3. DO NOT allow children or others to ride on machine,

attachments or towed equipment (even with the blades

OFF). They may fall and be seriously injured.

4. DO NOT allow pre-teenage children to operate machine.

5. ALLOW only responsible adults & teenagers with mature

judgment under close adult supervision to operate

machine.

6. DO NOT operate blades in reverse unless absolutely

necessary. STOP BLADES. LOOK and SEE behind and

down for children, pets and hazards before and while

backing.

7. USE EXTRA CARE when approaching blind corners,

shrubs, trees, or other objects that may obscure vision.

Protection Against Tip-Overs/Roll-Overs

Slopes are a major factor related to loss-of-control and

tipover/roll-over accidents, which can result in severe injury or

death. All slopes require extra CAUTION. If you cannot back

up the slope or if you feel uneasy on the slope, DO NOT mow

it. Use extra care with grass catchers or other attachments;

these affect the handling and the stability of the machine.

1. DO NOT operate machine on slopes exceeding 10

degrees (18% grade).

2. Turn blades OFF when traveling uphill. Use a slow speed

and avoid sudden or sharp turns.

3. DO NOT operate machine back and forth across face of

slopes. Operate up and down. Practice on slopes with

blades off.

4. AVOID starting, stopping or turning on slopes. If machine

stops going uphill or tires lose traction, turn blades OFF

and back slowly straight down the slope.

5. STAY ALERT for holes and other hidden hazards. Tall

grass can hide obstacles. Keep away from ditches, wash-

outs, culverts, fences and protruding objects.

6. KEEP A SAFE DISTANCE (at least two mower widths)

away from edge of ditches and other drop offs. The

machine could turn over if an edge caves in.

7. Always begin forward motion slowly and with caution.

8. DO NOT begin forward motion while the machine is roll-

ing backwards. A rearward tip-over may result.

9. Use weights or a weighted load carrier in accordance

with instructions supplied with a grass catcher or other

attachments. DO NOT operate machine on slopes

Not for

Reproduction

10

exceeding 10 degrees (18% grade) when equipped with

grass catcher or other attachments.

10. DO NOT put your foot on the ground to try to stabilize

the machine.

11. DO NOT operate machine on wet grass. Reduced trac-

tion could cause sliding.

12. Choose a low enough speed setting so that you will not

have to stop or shift on a slope. Tires may lose traction

on slopes even though the brakes are functioning prop-

erly.

13. DO NOT operate machine under any condition where

traction, steering or stability is doubtful.

14. Always keep the machine in gear when going down

slopes. DO NOT shift to neutral (or actuate hydro roll

release) and coast downhill.

15. Machine stability is tested in accordance with the appli-

cable ANSI B71 standard using an operator weight of

200 lbs. To minimize the risk of a tip-over or roll-over,

operators weighing more than 200 lbs. should further limit

the ground speed and the degree of slope to be mowed.

Preparation

1. Read, understand, and follow instructions and warnings

in this manual and on the machine, engine and attach-

ments. Know the controls and the proper use of the

machine before starting.

2. Only mature, responsible persons shall operate the

machine and only after proper instruction.

3. Data indicates that operators age 60 and above, are

involved in a large percentage of mower-related injuries.

These operators should evaluate their ability to operate

the mower safely enough to protect themselves and oth-

ers from serious injury.

4. Handle fuel with extra care. Fuels are flammable and

vapors are explosive. Use only an approved fuel con-

tainer. DO NOT remove fuel cap or add fuel with engine

running. Add fuel outdoors only with engine stopped and

cool. Clean spilled fuel from machine. DO NOT smoke.

5. Practice operation of machine with BLADES OFF to learn

controls and develop skills.

6. Check the area to be mowed and remove all objects

such as toys, wire, rocks, limbs and other objects that

could cause injury if thrown by blade or interfere with

mowing.

7. Keep people and pets out of mowing area. Immediately

STOP blades, STOP engine, and STOP machine if any-

one enters the area.

8. Check shields, deflectors, switches, blade controls and

other safety devices frequently for proper operation and

location.

9. Make sure all safety decals are clearly legible. Replace if

damaged.

10. Protect yourself when mowing and wear safety glasses,

a dust mask, hearing protection, long pants and substan-

tial footwear.

11. Know how to STOP blades and engine quickly in prepa-

ration for emergencies.

12. Use extra care when loading or unloading the machine

into a trailer or truck.

13. Check grass catcher components frequently for signs of

wear or deterioration and replace as needed to prevent

injury from thrown objects going through weak or worn

spots.

Safe Handling of Gasoline

To avoid personal injury or property damage, use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive.

1. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

2. Use only an approved fuel container.

3. DO NOT remove fuel cap or add fuel with the engine run-

ning. Allow the engine to cool before refueling.

4. DO NOT refuel the machine indoors.

5. DO NOT store the machine or fuel container inside

where there is an open flame, spark or pilot light such as

on a water heater or other appliances.

6. DO NOT fill fuel containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place the con-

tainers on the ground away from the vehicle before filling.

7. Remove gas-powered equipment from the vehicle or

trailer and refuel it on the ground. If this is not possible,

then refuel equipment using a portable container, rather

than a gasoline dispenser nozzle.

8. DO NOT start gas powered equipment in enclosed vehi-

cles or trailers.

9. Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete.

DO NOT use a nozzle lock-open device.

10. If fuel is spilled on clothing, change clothing immediately.

11. Never overfill a fuel tank. Replace fuel cap and tighten

securely.

Operation

1. Mount and dismount machine from left side. Keep clear

of discharge opening at all times.

2. Start engine from operator’s seat, if possible. Make sure

blades are OFF and parking brake is set.

3. DO NOT leave machine with engine running. STOP

engine, STOP blades, SET brake, and remove key before

leaving operators position of any reason.

4. DO NOT operate machine unless properly seated with

feet on feet rests or pedal(s).

Not for

Reproduction

11

en

5. STOP BLADES and ENGINE and make sure blades

have stopped before removing grass catcher or unclog-

ging mower to prevent loss of fingers or hand.

6. Blades must be OFF except when cutting grass. Set

blades in highest position when mowing over rough

ground.

7. Keep hands and feet away from rotating blades under-

neath deck. DO NOT place foot on ground while

BLADES are ON or machine is in motion.

8. DO NOT operate machine without entire grass catcher or

guards in place and working. DO NOT point discharge at

people, passing cars, windows or doors.

9. Slow down before turning.

10. Watch out for traffic when near or crossing roadways.

11. STOP engine immediately after striking an obstruction.

Inspect machine and repair damage before resuming

operation.

12. Operate machine only in daylight or with good artificial

light.

13. Exercise CAUTION when pulling loads. Limit loads to

those you can safely control and attach loads to hitch

plate as specified with attachment instructions.

14. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control. When towing,

travel slowly and allow extra distance to stop.

15. DO NOT operate engine in enclosed areas. Engine

exhaust gases contain carbon monoxide, a deadly poi-

son.

16. DO NOT discharge material against a wall or obstruc-

tion. Material may ricochet back towards the operator.

17. Only use accessories approved by the manufacturer.

See manufacturer’s instructions for proper operation and

installation of accessories.

18. Duration of machine operation may need to be limited

due to exposure to noise and vibration.

19. DO NOT operate machine when the risk of lightning is

present.

Towing

1. Tow only with a machine that has a hitch designed for

towing. DO NOT attach towed equipment except at the

hitch point.

2. Refer to “Towing Implements” in the Operation section

regarding weight limits for towed equipment and towing

on slopes.

3. DO NOT allow children or others on towed equipment.

4. On slopes, the weight of the towed equipment may cause

loss of traction and loss of control. Use caution while

operating on slopes.

5. Travel slowly and allow extra distance to stop.

Maintenance

1. DO NOT store machine or fuel container inside where

fumes may reach an open flame, spark or pilot light such

as in a water heater, furnace, clothes dryer or other gas

appliance. Allow engine to cool before storing machine

in an enclosure. Store fuel container out of the reach of

children in a well ventilated, unoccupied building.

2. Keep engine and machine free of grass, leaves or excess

grease to reduce fire hazard and engine overheating.

3. When draining fuel tank, drain fuel into an approved con-

tainer outdoors and away from open flame.

4. Check brakes frequently; adjust, repair or replace as

needed.

5. Keep all bolts, nuts and screws properly tight. Check that

all cotter pins are in proper position.

6. Always provide adequate ventilation when running

engine. Exhaust gases contain carbon monoxide, an

odorless and deadly poison.

7. Disconnect negative (black) cable from battery before

performing maintenance or service. Cranking engine

could cause injury.

8. DO NOT work under machine without safety blocks.

9. DO NOT stand unit on end.

10. Service engine and make adjustments only when engine

is stopped. Remove spark plug wire(s) from spark plug(s)

and secure wire(s) away from spark plug(s).

11. DO NOT change engine governor speed settings or

overspeed engine.

12. Lubricate machine at intervals specified in manual to

prevent controls from binding.

13. Mower blades are sharp and can cut. Wrap the blades

or wear heavy leather gloves and use CAUTION when

handling them.

14. DO NOT test for spark by grounding spark plug next

to spark plug hole; spark plug could ignite gas exiting

engine.

15. Have machine serviced by an authorized dealer at least

once a year and have the dealer install any new safety

devices.

16. Maintain or replace safety and instruction labels as nec-

essary.

17. Use only factory authorized replacement parts or equiva-

lent when making repairs.

Ignition System

1. This spark ignition system complies with Canadian

Standard ICES-002.

Safety and Instructional Decals

Before operating your unit, read and understand the safety

and instructional decals (compare Figure 1 with the table

Not for

Reproduction

12

below). The cautions, warnings, and instructions are for your

safety. To avoid personal injury or damage to the unit, under-

stand and follow all the decals.

A Clutch/Brake Operation

Blade Engage Operation

General Warnings

NOTE: Decal configura-

tion and location may

vary according to model.

7106108

3

50mm

B Forward Speed (Manual

Drive Models)

C Reverse Speed (Manual

Drive Models)

D Transmission Release

(Hydro Drive Models)

E Weight Limitation

F Engine Speed Control

Choke Control (Select

Models)

G Discharge Safety (2 - 1

on each side of deck)

7106109

H Cutting Height

WARNING

If any safety or instructional decals become worn or dam-

aged, and cannot be read, order replacement decals from

your dealer.

Safety Decal Icon Definitions

7106108

3

50mm

7106109

H I

A

B

C

D

E

F

G

A WARNING: Read and understand the Operator’s

Manual before using this machine. Know the loca-

tion and function of all controls. Do not operate this

machine unless you are trained.

B DANGER - THROWN OBJECTS AND AMPUTATION

HAZARD: To avoid injury, keep bystanders and chil-

dren away.

C DANGER - AMPUTATION HAZARD: Do not mow

when children or others are around. Do not mow in

reverse unless absolutely necessary. Look down and

behind - before and while backing. Never carry riders,

especially children, even with the blades off.

D DANGER - TIPOVER / ROLLOVER HAZARD: Mow

up and down slopes, not across. Do not operate on

slopes over 10 degrees.

E DANGER - AMPUTATION AND DISMEMBERMENT

HAZARD: To avoid injury from rotating blades and

moving parts, keep safety devices (guards, shields

and switches) in place and working.

Not for

Reproduction

13

en

Features and Controls

Compare the features and controls in Figure 2 with the table

below.

F DANGER: Remove key and consult technical lit-

erature before performing service or maintenance.

Remove objects that can be thrown by the blades.

G DANGER - FIRE HAZARD: Remove key and wait

three (3) minutes before refueling. When filling tank,

allow at least 50mm from top of fuel tank to allow for

expansion.

H DANGER - THROWN OBJECTS HAZARD: Do not

mow without discharge chute or entire grass catcher

in place.

I DANGER - THROWN OBJECTS AND AMPUTATION

HAZARD: To avoid injury from rotating blades, stay

clear of deck edge and keep others away.

Ref. Description Icon(s) Icon Definition

A Operator Seat -- --

B Steering Wheel -

controls direction of

unit

-- --

C Engine Speed

Control (hidden

from view) - controls

engine speed

Choke on (closed)

- if equipped

Engine speed fast

Engine speed low

D Cutting Height Adjust

Lever - adjusts cut-

ting height

Cutting height low

Cutting height

high

E Parking Brake Latch

(hidden from view) -

locks brake

Parking brake on

(engaged)

F Blade Control -

engages mower

blade

Blade on

(engaged)

Blade off (disen-

gaged

G Clutch/Brake Pedal

- engages clutch

(manual drive mod-

els) and brake

Clutch engaged

(manual drive

models)

Brake on

(engaged)

H Headlight (not shown;

select models)

-- --

I Mulching Cover -- --

Ref. Description Icon(s) Icon Definition

J Ignition Switch -

starts engine

Engine off

Engine on (run)

Engine start

K Transmission

Release Lever (hid-

den from view;

hydro drive models)

- releases transmis-

sion so unit can roll

freely

Transmission

engaged (locked)

Transmission

released

(unlocked)

L Reverse Mowing

Switch - temporarily

allows mower blade

to operate with trans-

mission in reverse

-- --

M Recoil Start Handle

(hidden from view)

-- --

N Transmission Shift

Lever (manual drive

models) - selects

transmission speed

and direction

Forward ground

speed

Neutral (no ground

speed)

Reverse ground

speed

O Fuel Tank -- --

P Fuel Gauge - indi-

cates amount of fuel

in fuel tank

-- --

Q Forward Ground

Speed Pedal (hydro

drive models) - con-

trols forward ground

speed

Forward ground

speed

R Reverse Ground

Speed Pedal (hydro

drive models) - con-

trols reverse ground

speed

Reverse ground

speed

Not for

Reproduction

14

Safety Interlock Systems Checks

DANGER

DO NOT operate machine if any safety interlock or safety

device is not in place and functioning properly. Contact

your dealer immediately for assistance. DO NOT attempt

to defeat, modify or remove any safety device.

Engine must not start if:

1. The Clutch/Brake Pedal is not fully depressed OR,

2. The Blade Control is in the ON (engaged) position.

Engine should start if:

1. The Blade Control is in the OFF (disengaged) position

AND,

2. The Clutch/Brake Pedal is fully depressed.

Engine and blade must stop if:

1. The operator rises off of the operator seat while the

Blade Control is in the ON (engaged) position OR,

2. The operator rises off of the operator seat while the

Clutch/Brake Pedal is not fully depressed OR,

3. The operator attempts to drive the unit in reverse with the

mower blade engaged and the reverse mowing option

function (RMO) not activated.

WARNING

Once mower blade is disengaged, it should come to a

complete stop in 5 seconds or less. If the blade continues

to rotate after 5 seconds, DO NOT operate the machine.

Return the machine to an authorized dealer for adjustment.

Operation

Before Starting

Make the following checks and perform the service required

before each start-up:

1. Check the tire pressure; add or release air as need-

ed. Refer to “How To Check Tire Pressure” in the

Maintenance section.

2. Check guards, deflectors and covers to make sure all are

in place and securely tightened.

3. Check engine oil and add oil as needed. Refer to “How

To Check/Add Oil”.

4. Add fuel to the fuel tank as needed. Refer to “How to Add

Fuel”.

5. Adjust the operator seat as needed to the most com-

fortable position. Refer to “How To Adjust The Operator

Seat”.

6. Check all operator controls to ensure they operate freely

without binding.

7. Perform the Safety Interlock System Checks. Refer to

“Safety Interlock System Checks”.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality deter-

gent oils are acceptable if classified for service SF, SG, SH,

SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

SAE 30 *

10W-30

†

Synthetic 5W-30

5W-30

A

B

C

D

A SAE 30 - Below 40°F (4°C) the use of SAE 30 will

result in hard starting.

B 10W-30 - Above 80°F (27°C) the use of 10W-30 may

cause increased oil consumption. Check oil level more

frequently.

C Synthetic 5W-30

D 5W-30

How To Check/Add Oil

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 3) and wipe with a clean

cloth.

NOTE: On some models, the dipstick is accessible through

an opening behind the operator seat.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should be

at the top of the full indicator (B) on the dipstick.

4. If low, add oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then

recheck the oil level.

5. Replace and tighten the dipstick.

Fuel Recommendations

Fuel must meet these requirements:

Not for

Reproduction

15

en

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude

use, see below.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Do not use unapproved gasolines, such as E15

and E85. Do not mix oil in gasoline or modify the engine to

run on alternate fuels. Use of unapproved fuels will damage

the engine components, which will not be covered under war-

ranty.

To protect the fuel system from gum formation, mix a fuel sta-

bilizer into the fuel. See Storage. All fuel is not the same. If

starting or performance problems occur, change fuel provid-

ers or change brands. This engine is certified to operate on

gasoline.

The emissions control system for this engine is EM (Engine

Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane/85 AKI (89 RON) gasoline is acceptable.

For carbureted engines, high altitude adjustment is required

to maintain performance. Operation without this adjustment

will cause decreased performance, increased fuel consump-

tion, and increased emissions. Contact a Briggs & Stratton

Authorized Service Dealer for high altitude adjustment infor-

mation. Operation of the engine at altitudes below 2,500 feet

(762 meters) with the high altitude adjustment is not recom-

mended.

For Electronic Fuel Injection (EFI) engines, no high altitude

adjustment is necessary.

How To Add Fuel

WARNING

Fuel and its vapors are extremely flammable and explo-

sive. Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 5 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Clean the fuel cap area of dirt and debris. Remove the

fuel cap (A, Figure 4).

2. Fill the fuel tank with fuel. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck (B).

NOTE: The fuel gauge (C) helps to determine the amount of

fuel in the tank.

3. Reinstall the fuel cap.

How To Adjust The Operator Seat

With the engine stopped:

1. Raise the operator seat.

2. Loosen the two adjusting knobs (A, Figure 5) and move

the seat to the desired position. After adjustment, tighten

the knobs securely.

3. Lower the operator seat.

How To Start The Engine

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains

carbon monoxide, a poisonous gas that could kill

you in minutes. You CANNOT see it, smell it, or taste

it. Even if you do not smell exhaust fumes, you could

still be exposed to carbon monoxide gas. If you start

to feel sick, dizzy, or weak while using this product,

shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

• Operate this product ONLY outside far away from win-

dows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for

hours, even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

Electric Start:

1. Sit squarely in the operator seat.

2. Manual Drive Models - Move the transmission shift lever

to the Neutral (‘N’) position. Refer to “How To Engage The

Transmission”.

WARNING

DO NOT start the engine with the transmission shift lever

in a drive position. Follow starting instructions carefully.

Not for

Reproduction

16

3. Make sure the Blade Control (A, Figure 6) is in the OFF

position.

4. Fully depress the Clutch/Brake Pedal (A, Figure 7).

5. Move the engine speed control (A, Figure 8) to the FAST

position (or CHOKE position, if equipped).

NOTE: The CHOKE position is not required when starting a

warm engine.

6. Insert the ignition key (A, Figure 9) into the ignition

switch. Turn the key to the START position until the

engine starts.

NOTE: When the ignition key is turned to START, the engine

will turn over, but will not start unless the Clutch/Brake pedal

is fully depressed and the Blade Control is in the OFF posi-

tion.

NOTE: If after 5 seconds of cranking the engine does not

start, release the key, make sure the Clutch/Brake Pedal is

fully depressed, and attempt starting again after waiting for

approximately 20 seconds.

7. After the engine starts, move the engine speed control to

the FAST position (if equipped with choke) and allow a

brief warm-up until engine runs smooth.

NOTE: Always operate with the engine speed control in the

FAST position.

NOTE: The headlight (featured on select models) is opera-

tional any time the ignition switch is in the RUN or START

position.

Recoil Start:

1. Manual Drive Models - Move the transmission shift lever

to the Neutral (‘N’) position. Refer to “How To Engage The

Transmission”.

WARNING

DO NOT start the engine with the transmission shift lever

in a drive position. Follow starting instructions carefully.

2. Make sure the Blade Control (A, Figure 6) is in the OFF

position.

3. Set the parking brake. Refer to “How To Set The Parking

Brake”.

4. Move the engine speed control (A, Figure 8) to the FAST

position (or CHOKE position, if equipped).

NOTE: The CHOKE position is not required when starting a

warm engine.

5. Insert the ignition key (A, Figure 10) into the ignition

switch. Turn the key to the RUN position (B).

6. Grasp the recoil start handle on the engine (A, Figure 11)

and pull briskly until the engine starts.

7. After the engine starts, move the engine speed control to

the FAST position (if equipped with choke) and allow a

brief warm-up period until engine runs smooth.

NOTE: Always operate with the engine speed control in the

FAST position.

NOTE: The headlight (featured on select models) is opera-

tional any time the ignition switch is in the RUN position.

How To Engage The Mower Blade

1. Start the engine.

2. Move the blade control (A, Figure 12) to the ON position.

How To Engage The Transmission

Manual Drive Models:

1. Start the engine.

2. To move forward:

• Depress the clutch/brake pedal (A, Figure 7).

• Move the transmission shift lever (A, Figure 13) from

the Neutral (‘N’) position (B) into the first forward speed

notch (C).

• Release the clutch/brake pedal to begin forward motion.

• During forward motion, the transmission shift lever may

be placed in any desired forward speed (D) without

depressing the clutch/brake pedal.

3. To move backward:

• Depress the clutch/brake pedal (A, Figure 7).

• Move the transmission shift lever (A, Figure 13) from the

Neutral (‘N’) position (B) into the reverse speed slot (E).

• During reverse motion, the transmission shift lever may

be placed in any desired reverse speed without depress-

ing the clutch/brake pedal.

Hydro Drive Models:

1. Start the engine.

2. Make sure the parking brake is released. Refer to “How

To Set The Parking Brake”.

3. To move forward:

• Slowly depress the forward ground speed pedal (A,

Figure 14) to begin forward motion. Increase ground

speed by further depressing the pedal.

4. To move backward:

• Slowly depress the reverse ground speed pedal (B,

Figure 14) to begin reverse motion. Increase ground

speed by further depressing the pedal.

NOTE: For best cutting results, choose a slow forward speed

with the engine speed control in the FAST position. This com-

bination will allow the mower blade to lift the grass while cut-

ting smoothly and evenly.

NOTICE

If the transmission is moved into reverse while the mower

blade is engaged, the engine will shut off. If mowing in

reverse is necessary, refer to “Reverse Mowing Option

(RMO)”.

Not for

Reproduction

17

en

WARNING

LOOK and SEE behind and down for children, pets and

hazards before and while backing.

WARNING

DO NOT leave the machine with the engine running. STOP

Blade. STOP engine. Shift to neutral and engage parking

brake. Remove key.

How To Stop The Engine, Transmission

And Mower Blade

Engine

1. Stop the engine by turning the ignition key (A, Figure 15)

to the OFF position.

2. Remove the key.

Transmission

• Manual Drive Models:

1. Stop motion of the unit by fully depressing the clutch/

brake pedal (A, Figure 7) to disengage the clutch and

apply the brake.

2. Return the transmission shift lever to the Neutral (‘N’)

position. Refer to “How To Engage The Transmission”.

• Hydro Drive Models:

1. Stop motion of the unit by fully releasing the ground

speed pedals (A, Figure 16). Additional braking can be

achieved by depressing the brake pedal (A, Figure 7).

Mower Blade

1. Stop the mower blade by moving the blade control (A,

Figure 6) to the OFF position.

WARNING

Once blade is disengaged, it should come to a complete

stop in 5 seconds or less. If the blade continues to rotate

after 5 seconds, the blade brake must be adjusted. Return

machine to an authorized dealer for adjustment. DO NOT

CONTINUE to operate machine until blade brake is adjust-

ed and functioning properly.

How To Set The Parking Brake

1. Fully depress the clutch/brake pedal (A, Figure 17).

2. Slide the parking brake latch (B) up and hold while

releasing the clutch/brake pedal. The parking brake is

now set.

3. To release the parking brake, fully depress the clutch/

brake pedal. The parking brake will release automatically.

WARNING

DO NOT park the machine on slopes.

How To Adjust The Cutting Height

1. Raise or lower the cutting height adjust lever (A, Figure

18) into the desired height of cut notch.

Reverse Mowing Option (RMO)

WARNING

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the pres-

ence of children. Never activate RMO if children are pres-

ent. Children are often attracted to the unit and the mowing

activity.

1. Engage the mower blade. Refer to “How To Engage The

Mower Blade”.

2. Insert the supplied key (A, Figure 19) into the RMO

switch (B), and turn the key to activate the RMO function.

The LED light (C) indicates that the RMO function is now

activated.

3. Engage the transmission in reverse. Refer to “How To

Engage The Transmission”.

4. The RMO function is deactivated when the mower blade

is disengaged.

How To Install The Discharge Deflector

WARNING

DO NOT attempt any adjustments, maintenance, service

or repairs with the engine running.

• STOP engine.

• STOP blade.

• Engage parking brake.

• Remove key.

• Remove spark plug wire from spark plug and secure

away from plug.

• Engine and components are HOT. Avoid serious burns,

allow all parts to cool before working on machine.

1. Remove the nut and washer (A, Figure 20) securing the

bottom edge of the mulching cover (B) to the mower

deck.

WARNING

The mulching cover must remain on the machine at all

times. Do not remove.

Not for

Reproduction

18

2. Raise the mulching cover. Replace the washer and nut

onto the retaining bolt in the deck, tightening securely.

3. Install the discharge deflector (A, Figure 21) to the

mower deck, making sure that the slots (B) in the deflec-

tor fit over the locking tabs (C) on the mulching cover

hinge bracket.

4. Lower the mulching cover.

5. To remove the discharge deflector:

• Raise the mulching cover.

• Lift and remove the discharge deflector from the mower

deck.

• Remove the nut and washer from the retaining bolt in the

deck.

• Lower the mulching cover, securing with the washer and

nut. Tighten securely.

How To Push The Unit By Hand

Manual Drive Models:

1. Make sure the unit is parked on a flat, even surface.

2. Make sure the transmission shift lever is in the Neutral

(N) position. Refer to “How To Engage the Transmission”.

3. Release the parking brake, if set. Refer to “How To Set

The Parking Brake”.

4. The unit can now be pushed by hand. Be sure to set the

parking brake after the unit is moved to the desired loca-

tion.

Hydro Drive Models:

1. Make sure the unit is parked on a flat, even surface.

2. Release the parking brake, if set. Refer to “How To Set

The Parking Brake”.

3. Move the transmission release lever (located behind

the right rear tire) out and down into the locking slot (A,

Figure 22) to disengage the transmission.

4. The unit can now be pushed by hand.

5. After moving the unit to the desired location, move the

transmission release lever up and in (B) to engage the

transmission.

Towing A Trailer

The maximum horizontal drawbar force allowed is 34 lbs (150

N) *. The maximum vertical drawbar force is 20 lbs (90 N) *.

* Approximate

Maintenance

WARNING

DO NOT attempt any adjustments, maintenance, service

or repairs with the engine running.

• STOP engine.

• STOP blade.

• Engage parking brake.

• Remove key.

• Remove spark plug wire from spark plug and secure

away from plug.

• Engine and components are HOT. Avoid serious burns,

allow all parts to cool before working on machine.

Maintenance Schedule

RIDER

Every 8 Hours or Daily

• Check safety interlock system

• Clean debris off rider

• Clean debris from engine area

Every 25 Hours or Annually *

• Check tire pressure

• Check mower blade stopping time

• Check rider for loose hardware

Every 50 Hours or Annually *

• Clean battery and cables

• Check brakes

See Dealer Annually to

• Lubricate rider

• Check mower drive belts

• Check mower blades **

* Whichever comes first

** Check blades more often in regions with sandy soils or

high dust conditions.

Not for

Reproduction

19

en

ENGINE

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check engine oil level

Every 25 Hours or Annually *

• Clean engine air filter and pre-cleaner **

Every 50 Hours or Annually *

• Change engine oil

• Replace oil filter

Annually

• Replace air filter

• Replace pre-cleaner

See Dealer Annually to

• Inspect muffler

• Replace spark plug

• Replace fuel filter

• Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne

debris is present.

Engine Maintenance

How To Change The Engine Oil

Used oil is a hazardous waste product and must be disposed

of properly. Do not discard with household waste. Check with

your local authorities, service center, or dealer for safe dis-

posal/recycling facilities.

1. Place bricks or wooden blocks under the front wheels to

lower the rear of the engine.

2. Loosen or remove the oil fill cap on the engine.

3. Place a 2 quart minimum capacity container under the

end of the oil drain (Figure 23).

4. Remove or open the oil drain plug (A or B, Figure 23),

depending upon the type of oil drain plug the engine is

equipped with.

NOTE: Location of oil drain may vary according to model.

5. After all the oil has drained, replace or close the drain

plug, and wipe up any oil that may have spilled. Dispose

of used oil properly.

6. Fill the engine with new oil. Refer to “How To Check/Add

Oil” in the Operation Section.

How To Change The Oil Filter (if equipped)

Some models are equipped with oil filter. For replacement

intervals, see the Maintenance chart.

1. Drain the oil from the engine. Refer to “How To Change

The Engine Oil”.

2. Remove the oil filter (A, Figure 24) and dispose of prop-

erly.

NOTE: Location of oil filter may vary according to model.

3. Before you install the new oil filter, lightly lubricate the oil

filter gasket with fresh, clean oil.

4. Install the oil filter by hand until the gasket contacts the

oil filter adapter, then tighten the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to “How to Check/Add Oil” in the Operation

section.

6. Start and run the engine. As the engine warms up, check

for oil leaks.

7. Stop the engine and check the oil level. It should be at

the top of the full indicator on the dipstick.

How To Service The Air Filter

WARNING

Fuel and its vapors are extremely flammable and explo-

sive. Fire or explosion can cause severe burns or death.

• Never start or run the engine with the air cleaner

assembly (if equipped) or the air filter (if equipped)

removed.

NOTICE

Do not use pressurized air or solvents to clean the filter.

Pressurized air can damage the filter and solvents will dis-

solve the filter.

Flat Air Filter

1. Pull up on the cover handle (A, Figure 25). Rotate the

cover handle toward the engine and then remove the

cover (B).

2. Remove the pre-cleaner (C), if equipped, and the filter

(D).

3. To loosen debris, gently tap the filter on a hard surface. If

the filter is excessively dirty, replace with a new filter.

4. Wash the pre-cleaner in liquid detergent and water. Then

allow it to thoroughly air dry. Do not oil the precleaner.

5. Assemble the dry pre-cleaner and the filter into the

engine base (E).

6. Align the tabs (F) on the cover with the slots (G) in the

blower housing. Rotate the cover handle back and push

down to lock in place.

Cylindrical Cartridge Air Filter

1. Remove the fasteners (A, Figure 26) and the air filter

cover (B).

2. To remove the filter (C), lift the end of the filter and then

pull the filter off the intake (D).

Not for

Reproduction

20

3. Remove the pre-cleaner (E), if equipped, from the filter.

4. To loosen debris, gently tap the filter on a hard surface. If

the filter is excessively dirty, replace with a new filter.

5. Wash the pre-cleaner in liquid detergent and water. Then

allow it to thoroughly air dry. Do not oil the precleaner.

6. Assemble the dry pre-cleaner to the filter.

7. Install the filter on the intake. Push the end of the filter

into the base as shown. Make sure filter fits securely in

the base.

8. Install air filter cover and secure with fasteners.

Rider Maintenance (Basic)

How To Check The Safety Interlock System

Refer to “Safety Interlock System Checks” in the Operation

section.

How To Clean The Rider And Mower Deck

WARNING

Wear heavy leather gloves when handling or working

around cutting blades. Blades are extremely sharp and can

cause severe injury.

1. Raise the mower deck to the highest cutting position.

Refer to “How To Adjust The Cutting Height”.

2. Clean the underside of the mower deck, removing all

accumulation of grass clippings and debris.

3. Clean the top of the deck, removing all grass clippings

and debris.

4. Use a brush or compressed air to remove loose debris

from the rider.

How To Clean The Engine

Use a brush or compressed air to remove loose debris on or

around the engine.

How To Check Tire Pressure

Use a tire gauge to check the tire pressure; add or release air

as needed. Refer to “Product Specifications” for correct pres-

sure.

How To Check Mower Blade Stopping Time

WARNING

The following procedure requires the engine and blades to

be operated. Exercise extreme caution. Clear area of loose

parts & tools first. Only operate blades when seated in the

operator’s seat.

1. Start the engine.

2. Engage the mower blade.

3. Disengage the mower blade. The blade should stop rotat-

ing in 5 seconds or less after moving the blade control to

the OFF position.

WARNING

Blade must stop rotating in 5 seconds or less after the

blade has been turned off. DO NOT operate machine.

Contact an authorized dealer for adjustment.

4. If the blade continues to rotate longer than 5 seconds, do

not operate the machine. Contact an authorized dealer

for assistance.

NOTE: Any adjustments and service regarding mower blade

stopping time should be performed by an authorized dealer.

How To Perform Battery Service

Refer to “Battery Service”.

How To Check The Brake / Parking Brake

1. Check the machine brake for proper function:

• Engage the parking brake, and push the machine. The

rear tires should skid.

• Drive the machine forward and apply the brake. The

machine should come to a complete stop in less than 5

feet (1,5 meters).

2. If the brakes are not functioning properly, do not operate

the machine. Contact an authorized dealer for service.

Rider Maintenance (Advanced)

WARNING

DO NOT stand the unit on end. Attempting to do so may

cause an unstable condition, resulting in serious injury or

equipment damage.

How To Check The Mower Blade

DANGER

DO NOT use a cutting blade that shows signs of excessive

wear or damage.

1. Check the torque of the blade mounting bolts (A, Figure

27). As necessary, torque to 30 to 40 ft. lbs (41 - 54 Nm).

2. Check the blade for sharpness, wear and damage. Refer

to “How To Inspect The Mower Blade”.

3. Check the blade for straightness. Refer to “How To Adjust

The Mower Blade”.

How To Check The Mower Drive Belts

The mower drive belts should be checked by an authorized

dealer for wear or damage, as well as for correct tension.

Refer to the Maintenance Schedule.

Sayfa yükleniyor ...

Simplicity 2691354-00 Kullanım kılavuzu

Bu kılavuz için de uygundur

Simplicity 2691354-00 Kullanım kılavuzu

Diğer dillerde

İlgili Makaleler