Simplicity TRACTOR, EURO, RDLT Kullanım kılavuzu

Not for

Reproduction

80026953EST

Revision B

Operator’s Manual



Návod k obsluze

Kasutusjuhend

Használati útmutató

Vartotojo vadovas





Manual de utilizare



Návod na obsluhu





Not for

Reproduction

1

A

C

D

E

G

B

A

1 2

3

4

5 6

7

8

B

C

1730202

D

E

F

9

(

)

20

LB

(

)

34

LB

_

10

2

Not for

Reproduction

2

STOPSTOP

3

Not for

Reproduction

3

4

Not for

Reproduction

6

B

A

B

C

A

5

Size PSI bar

15 x 6,0 14 0,96

20 x 8,0 10 0,68

22 x 9.5 10 0,68

4

5

Not for

Reproduction

9

10

11

A

B

WARNING

DO NOT REMOVE

COVER

WARNING

DO NOT REMOVE

COVER

WARNING

DO NOT REMOVE

COVER

A

B

( )

7

1730202

A

B

8

6

Not for

Reproduction

13

A

15

AB

12

14

A

B

D

C

7

Not for

Reproduction

Products Covered by This Manual

The following products are covered by this manual:

2691485-00, 2691486-00, 2691491-00, 2691492-00,

2691509-00, 2691510-00

Manual Contents

Operator Safety ................................................................. 9

Features and Controls...................................................... 14

Operation ......................................................................... 16

Safety Interlock System Tests .......................................... 16

Maintenance .................................................................... 20

Troubleshooting ............................................................... 24

 .................................................................. 26

The images in this document are representative, and

are meant to complement the instructional copy they

accompany. Your unit may vary from the images displayed.

LEFT and RIGHT are as seen from the operator’s position.

8

Not for

Reproduction

Operator Safety

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during the

initial set-up, the operation, and the maintenance of the

equipment. Save these original instructions for future

reference.

Safety Symbols and Meanings

FIRE MOVING

PARTS

SHOCK

STOP TOXIC FUMES KICKBACK

EXPLOSION ON OFF WEAR EYE

PROTECTION

HAZARDOUS

CHEMICAL

HOT

SURFACE

CHOKE

READ

MANUAL

FAST SLOW OIL

FUEL FUEL

SHUT-OFF

AMPUTATION

HAZARD

ROLL-OVER HAZARD

The safety alert symbol is used to identify safety

information about hazards that can result in personal injury.

A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to indicate the likelihood and the

potential severity of injury. In addition, a hazard symbol may

be used to represent the type of hazard.

DANGER indicates a hazard which, if not

avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate injury.

NOTICE indicates a situation that could result in

damage to the product.

WARNING

Running engine gives off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause headache, fatigue,

dizziness, vomiting, confusion, seizures, nausea, fainting

or death.

• Operate equipment ONLY outdoors.

• Keep exhaust gas from entering a confined area

through windows, doors, ventilation intakes, or other

openings.

9

Not for

Reproduction

GENERAL OPERATION

1. Read, understand, and follow all instructions in the manual

and on the unit before starting.

2. Do not put hands or feet near rotating parts or under the

machine. Keep clear of the discharge opening at all times.

3. Only allow responsible adults, who are familiar with the

instructions, to operate the unit (local regulations can

restrict operator age).

4. Clear the area of objects such as rocks, toys, wire, etc.,

which could be picked up and thrown by the blade(s).

5. Be sure the area is clear of other people before mowing.

Stop the unit if anyone enters the area.

6. Never carry passengers.

7. Do not mow in reverse unless absolutely necessary.

Always look down and behind before and while travelling in

reverse.

8. Never direct discharge material toward anyone. Avoid

discharging material against a wall or obstruction.

Material may ricochet back toward the operator. Stop the

blade(s) when crossing gravel surfaces.

9. Do not operate the machine without the entire grass

catcher, discharge guard (deflector), or other safety

devices in place.

10. Slow down before turning.

11. Never leave a running unit unattended. Always disengage

the PTO, set parking brake, stop engine, and remove

starter insert before dismounting.

12. Disengage blades (PTO) when not mowing. Shut off

engine and wait for all parts to come to a complete stop

before cleaning the machine, removing the grass catcher,

or unclogging the discharge guard.

13. Operate the machine only in daylight or good artificial light.

14. Do not operate the unit while under the influence of alcohol

or drugs.

15. Watch for traffic when operating near or crossing

roadways.

16. Use extra care when loading or unloading the unit into a

trailer or truck.

17. Always wear eye protection when operating this unit.

18. Data indicates that operators, age 60 years and above,

are involved in a large percentage of power equipment-

related injuries. These operators should evaluate their

ability to operate the equipment safely enough to protect

themselves and others from injury.

19. Follow the manufacturer’s recommendations for wheel

weights or counterweights.

20. Keep in mind the operator is responsible for accidents

occurring to other people or property.

21. All drivers should seek and obtain professional and

practical instruction.

22. Always wear substantial footwear and trousers. Never

operate when barefoot or wearing sandals.

23. Before using, always visually check that the blades and

blade hardware are present, intact, and secure. Replace

worn or damaged parts.

24. Disengage attachments before: refueling, removing an

attachment, making adjustments (unless the adjustment

can be made from the operator’s position).

25. When the machine is parked, stored, or left unattended,

lower the cutting means unless a positive mechanical lock

is used.

26. Before leaving the operator’s position for any reason,

engage the parking brake, disengage the PTO, stop the

engine, and remove the starter insert.

27. To reduce fire hazard, keep the unit free of grass, leaves,

& excess oil. Do not stop or park over dry leaves, grass, or

combustible materials.

TRANSPORTING AND STORAGE

1. When transporting the unit on an open trailer, make sure

it is facing forward, in the direction of travel. If the unit is

facing backwards, wind lift could damage the unit.

2. Always observe safe refueling and fuel handling practices

when refueling the unit after transportation or storage.

3. Never store the unit (with fuel) in an enclosed poorly

ventilated structure. Fuel vapors can travel to an ignition

source (such as a furnace, water heater, etc.) and cause

an explosion. Fuel vapor is also toxic to humans and

animals.

4. Always follow the engine manual instructions for storage

preparations before storing the unit for both short and long

term periods.

5. Always follow the engine manual instructions for proper

start-up procedures when returning the unit to service.

6. Never store the unit or fuel container inside where there is

an open flame or pilot light, such as in a water heater. Allow

unit to cool before storing.

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit,

severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck

is capable of amputating hands and feet and throwing objects. The triangle in text signifies important

cautions or warnings which must be followed.

10

Not for

Reproduction

WARNING

Never operate on slopes greater than 17.6 percent (10°)

which is a rise of 3-1/2 feet (106 cm) vertically in 20 feet

(607 cm) horizontally.

When operating on slopes use additional wheel weights

or counterweights. See your dealer/retailer to determine

which weights are available and appropriate for your unit.

Select slow ground speed before driving onto slope.

In addition to front weights, use extra caution when

operating on slopes with rear-mounted grass catchers.

Mow UP and DOWN the slope, never across the face,

use caution when changing directions and DO NOT

START OR STOP ON SLOPE.

CHILDREN

Tragic accidents can occur if the operator is not alert to the

presence of children. Children are often attracted to the unit

and the mowing activity. Never assume that children will

remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of another responsible adult.

2. Be alert and turn unit off if children enter the area.

3. Before and during reverse operation, look behind and

down for small children.

4. Never carry children, even with the blade(s) off. They may

fall off and be seriously injured or interfere with safe unit

operation. Children who have been given rides in the past

may suddenly appear in the mowing area for another ride

and be run over or backed over by the machine.

5. Never allow children to operate the unit.

6. Use extra care when approaching blind corners, shrubs,

trees, or other objects that may obscure vision.

SLOPE OPERATION

Slopes are a major factor related to loss-of-control and tip-

over accidents, which can result in severe injury or death.

Operation on all slopes requires extra caution. If you

cannot back up the slope or if you feel uneasy on it, do not

operate on it.

Control of a ride-on machine sliding on a slope will not be

regained by the application of the brake. The main reasons

for loss of control are: insufficient tire grip on the ground,

speed too fast, inadequate braking, the type of machine

is unsuitable for its task, lack of awareness of the ground

conditions, incorrect hitching and load distribution.

1. Mow up and down slopes, not across.

2. Watch for holes, ruts, or bumps. Uneven terrain could

overturn the unit. Tall grass can hide obstacles.

3. Choose a slow speed so that you will not have to stop or

change speeds while on the slope.

4. Do not mow on wet grass. Tires may lose traction.

5. Always keep unit in gear especially when traveling down

slopes. Do not shift to neutral and coast downhill.

6. Avoid starting, stopping, or turning on a slope. If tires

lose traction, disengage the blade(s) and proceed slowly

straight down the slope.

7. Keep all movement on slopes slow and gradual. Do

not make sudden changes in speed or direction, which

could cause the machine to rollover.

8. Use extra care while operating machines with grass

catchers or other attachments; they can affect the

stability of the unit. Do not use on steep slopes.

9. Do not try to stabilize the machine by putting your foot on

the ground (ride-on units).

10. Do not mow near drop-offs, ditches, or embankments.

The mower could suddenly turn over if a wheel is over

the edge of a cliff or ditch, or if an edge caves in.

11. Do not use grass catchers on steep slopes.

12. Do not mow slopes if you cannot back up them.

13. See your authorized dealer/retailer for recommendations

of wheel weights or counterweights to improve stability.

14. Remove obstacles such as rocks, tree limbs, etc.

15. Use slow speed. Tires may lose traction on slopes even

through the brakes are functioning properly.

16. Do not turn on slopes unless necessary, and then, turn

slowly and gradually downhill, if possible.

TOWED EQUIPMENT (RIDE-ON UNITS)

1. Tow only with a machine that has a hitch designed for

towing. Do not attach towed equipment except at the

hitch point.

2. Follow the manufacturer’s recommendations for weight

limit for towed equipment and towing on slopes.

3. Never allow children or others in or on towed equipment.

4. On slopes, the weight of the towed equipment may

cause loss of traction and loss of control.

5. Travel slowly and allow extra distance to stop.

6. Do not shift to neutral and coast down hill.

11

Not for

Reproduction

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1. Extinguish all cigarettes, cigars, pipes, and other sources

of ignition.

2. Use only approved gasoline containers.

3. Never remove the gas cap or add fuel with the engine

running. Allow the engine to cool before refueling.

4. Never fuel the machine indoors.

5. Never store the machine or fuel container where there is an

open flame, spark, or pilot light such as near a water heater

or other appliance.

6. Never fill containers inside a vehicle or on a truck bed with

a plastic bed liner. Always place containers on the ground

away from your vehicle before filling.

7. Remove gas-powered equipment from the truck or

trailer and refuel it on the ground. If this is not possible,

then refuel such equipment on a trailer with a portable

container, rather than from a gasoline dispenser nozzle.

8. Keep nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock-open device.

9. If fuel is spilled on clothing, change clothing immediately.

10. Never over-fill the fuel tank. Replace gas cap and tighten

securely.

11. Use extra care in handling gasoline and other fuels. They

are flammable and vapors are explosive.

12. If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors have

dissipated.

13. Replace all fuel tank caps and fuel container caps securely.

Service & Maintenance

1. Never run the unit in an enclosed area where carbon

monoxide fumes may collect.

2. Keep nuts and bolts, especially blade attachment bolts,

tight and keep equipment in good condition.

3. Never tamper with safety devices. Check their proper

operation regularly and make necessary repairs if they are

not functioning properly.

4. Keep unit free of grass, leaves, or other debris build-up.

Clean up oil or fuel spillage and remove any fuel-soaked

debris. Allow machine to cool before storage.

5. If you strike an object, stop and inspect the machine.

Repair, if necessary, before restarting.

6. Never make adjustments or repairs with the engine

running.

7. Check grass catcher components and the discharge guard

frequently and replace with manufacturer’s recommended

parts, when necessary.

8. Mower blades are sharp. Wrap the blade or wear gloves,

and use extra caution when servicing them.

9. Check brake operation frequently. Adjust and service as

required.

10. Maintain or replace safety and instructions labels, as

necessary.

11. Do not remove the fuel filter when the engine is hot as

spilled gasoline may ignite. Do not spread fuel line clamps

further than necessary. Ensure clamps grip hoses firmly

over the filter after installation.

12. Do not use gasoline containing METHANOL, gasohol

containing more than 10% ETHANOL, gasoline additives,

or white gas because engine/fuel system damage could

result.

13. If the fuel tank must be drained, it should be drained

outdoors.

14. Replace faulty silencers/mufflers.

15. Use only factory authorized replacement parts when

making repairs.

16. Always comply with factory specifications on all settings

and adjustments.

17. Only authorized service locations should be utilized for

major service and repair requirements.

18. Never attempt to make major repairs on this unit unless

you have been properly trained. Improper service

procedures can result in hazardous operation, equipment

damage and voiding of manufacturer’s warranty.

19. On multiple blade mowers, take care as rotating one blade

can cause other blades to rotate.

20. Do not change engine governor settings or over-speed

the engine. Operating the engine at excessive speed can

increase the hazard of personal injury.

21. Disengage drive attachments, stop the engine, remove the

starter insert, and disconnect the spark plug wire(s) before:

clearing attachment blockages and chutes, performing

service work, striking an object, or if the unit vibrates

abnormally. After striking an object, inspect the machine for

damage and make repairs before restarting and operating

the equipment.

22. Never place hands near the moving parts, such as a hydro

pump cooling fan, when the tractor is running. (Hydro

pump cooling fans are typically located on top of the

transaxle).

23. Units with hydraulic pumps, hoses, or motors:

WARNING: Hydraulic fluid escaping under pressure may

have sufficient force to penetrate skin and cause serious

injury. If foreign fluid is injected into the skin it must be

surgically removed within a few hours by a doctor familiar

with this form of injury or gangrene may result. Keep

body and hands away from pin holes or nozzles that

eject hydraulic fluid under high pressure. Use paper or

cardboard, and not hands, to search for leaks. Make sure

all hydraulic fluid connections are tight and all hydraulic

hoses and lines are in good condition before applying

pressure to the system. If leaks occur, have the unit

serviced immediately by your authorized dealer.

24. WARNING: Improper release of springs can result in

serious personal injury. Springs should be removed by an

authorized technician.

25. Models equipped with an engine radiator:

WARNING: To prevent serious bodily injury from hot

coolant or steam blow-out, never attempt to remove the

radiator cap while the engine is running. Stop the engine

and wait until it is cool. Even then, use extreme care when

removing the cap.

12

Not for

Reproduction

Safety Decals

All safety messages on your rider and mower should be

carefully read and obeyed (see Figure 1 and 2). Personal

bodily injury can result when these instructions are

not followed. The information is for your safety and it is

important! The safety decals below are on your rider and

mower.

If any of these decals are lost or damaged, replace them at

once. See an authorized dealer for replacements.

These labels are easily applied and will act as a constant

visual reminder to you, and others who may use the

equipment, to follow the safety instructions necessary for

safe, effective operation.

Callout Decal Description

A

DANGER, Main Panel

B

Decal: Height of Cut

C

Decal: Roll Release

D DANGER, Thrown Objects

E DANGER, Drawbar Warning

F DANGER, Rotating Blades

Safety Icon

See Figure 1 and 2 (callouts A, D, F) for location of

icons. See below for an explanation of these icons.

1. WARNING: Read and understand the Operator’ Manual

before using this machine. Know the location and

function of all controls. Do not operate this machine

unless you are trained.

2. DANGER - LOSS OF TRACTION, SLIDING,

STEERING AND CONTROL ON SLOPES HAZARD:

If machine stops forward motion or starts sliding on a

slope, stop the blades and drive slowly off the slope.

3. DANGER: FIRE HAZARD: Keep unit free of grass,

leaves and excess oil. Do not add fuel while engine is

hot or running. Stop engine, remove key and allow to

cool for at least 3 minutes prior to adding fuel. Do not

add fuel indoors, in an enclosed trailer, garage or other

enclosed areas. Clean up spilled fuel. Do not smoke

while operating this machine.

4. DANGER - TIPPING AND SLIPPING HAZARD: Mow

up and down slopes not across. Do not operate on

slopes over 10 degrees. Avoid sudden and sharp (fast)

turns while on slopes.

5. DANGER - AMPUTATION AND DISMEMBERMENT

HAZARD: To avoid injury from rotating blades and

moving parts, keep safety devices (guards, shields and

switches) in place and working.

6. Do not mow when children or others are around. Never

carry riders especially children even with the blades

off. Do not mow in reverse unless absolutely necessary.

Look down and behind – before and while backing.

7. Consult technical literature before performing technical

repairs or maintenance. When leaving the machine,

shutoff engine, set the parking brake to the lock position

and remove the ignition key.

8. Keep by-standers and children a safe distance away.

Remove objects that can be thrown by the blade. Do not

mow without discharge chute in place.

9. DANGER - THROWN OBJECTS: Do not operate with-

out first connecting the discharge tube.

10. DANGER - ROTATING BLADES: This mower deck can

amputate limbs. Keep hands and feet away from blades.

13

Not for

Reproduction

Features and Controls

See Figure 2 for location.

Throttle/Choke Control

(Choke-A-Matic)

The throttle/choke controls the engine speed and

choke (see Figure 2). Move the throttle/choke

control to the FAST position to increase engine

speed and SLOW position to decrease engine

speed. Always operate at full throttle. Move the

throttle/choke control to the CHOKE position for

starting a cold engine. A warm engine may not

require choking.

NOTE: Always operate the rider with the throttle/

choke control in the FAST position.

Reverse Mowing Option (RMO)

The Reverse Mowing Option allows for mowing

(or use of other PTO driven attachments) while

traveling in reverse. If you choose to mow or

operate another attachment in reverse, turn the

RMO key after the PTO is engaged. The L.E.D.

light will illuminate, and the operator can then mow

in reverse. Each time the PTO is disengaged the

RMO needs to be reactivated if desired.

Power Take-Off (PTO) Switch

The PTO (Power Take-Off) switch engages and

disengages attachments that use the PTO. To

engage the PTO, pull UP on the switch. Push

DOWN to disengage.

NOTE: that the operator must be seated firmly in

the tractor seat for the PTO to function.

Ignition Switch

The ignition switch starts and stops the engine,

and it controls the headlights. It has four positions:

OFF Stops the engine and shuts off the

electrical system.

RUN Allows the engine to run and

powers the electrical system.

START Cranks the engine for starting.

HEAD-

LIGHTS

The headlight position on the

ignition switch turns the headlight

ON and OFF.

NOTE: Never leave the ignition switch in the RUN

position with the engine stopped–this drains the

battery.

Ground Speed Pedals

The tractor’s forward ground speed is controlled

by the forward ground speed control pedal. The

tractor’s reverse ground speed is controlled by

the reverse ground speed control pedal.

Depressing either pedal will increase ground

speed. Note that the further down the pedal is

depressed, the faster the tractor will travel.

Seat Adjustment Lever

The seat can be adjusted forward and back.

Move the lever, position the seat as desired, and

release the lever to lock the seat into position.

Catcher Full Alarm

The “catcher full” alarm sounds when the grass

catcher has been filled with cut grass. When the

alarm sounds, disengage the PTO, travel to the

area in which you desire to dump the grass, then

empty the catcher.

NOTE: When using the unit for leaf collection, the

alarm may not be activated by dry leaves.

Parking Brake Knob

This is used to lock the parking brake when the

tractor is stopped. Fully depressing the brake

pedal and pulling up on the knob engages the

parking brake.

Cruise Control

The cruise control is used to lock the ground

speed control in forward. The cruise control has

five lock positions.

Hourmeter (if equipped)

The hourmeter displays the total hours, trip hours,

and digital clock. Also provides maintenance

reminder for oil, air filter, blade sharpening (icon

warning) and battery level indicator.

Electronic Dash Panel (if equipped)

The hourmeter displays the total hours, trip hours,

and digital clock. Also provides maintenance

reminder for oil, air filter, blade sharpening (icon

warning) and battery level indicator.

14

Not for

Reproduction

Fuel Tank

Turn cap counterclockwise to remove.

Fuel Level Gauge (if equipped)

Displays the fuel level in the tank.

Mower Lift Lever

This controls the mower cutting height. Pull lever

to lower the height and pull up to raise the height.

The cutting height is adjustable between 3,8 cm

(1,5”) and 8,9 cm (3,5”).

Electronic Dash Panel

Display Total Hours, Trip Hours, and Clock

NOTE: Whenever you start up the unit, the Total Hours are

displayed. The Total Hours will automatically reset to 0 after

999.9.

1. Press MODE for less than 1 second to display the Trip

Hours.

2. Press RESET for greater than 3 seconds to reset the

Trip Hours to 0.

3. Press MODE for less than 1 second to display the Clock

(see Set the Clock section).

4. Press MODE for less than 1 second to return to Total

Hours.

Catcher Open/Close Lever

This opens the catcher so that it may be emptied

and closes it for mowing. To empty the catcher,

extend the grass catcher handle and pull forward

on the handle. To close, push the lever backward

until the catcher closes and locks. Release the

grass catcher handle.

Transmission Release Lever

This deactivates the transmission so that

the tractor can be pushed by hand. See

Pushing the Tractor By Hand.

Set the Clock

1. Press MODE for greater than 3 seconds. The hours will

flash on the display.

2. Press RESET to adjust the hours.

3. Press MODE for less than 1 second to save the setting.

The minutes will flash on the display.

4. Press RESET to adjust the minutes.

5. Press MODE for less than 1 second to save the setting.

Maintenance Display

OIL CHANGE – This message appears after 50 hours of

run time since the previous reset. After changing the oil and

oil filter, press MODE twice to display OIL HRS, then press

and hold the MODE button for 3 seconds to reset the timer

to zero and clear the display.

CHECK AIR FILTER – This message appears after 25

hours of run time since the previous reset. After cleaning or

changing the air filter, press MODE three times to display

AIR FILTER HRS, then press and hold the MODE button for

3 seconds to reset the timer to zero and clear the display.

CHANGE BLADES – This message appears after 100

hours of run time since the previous reset. After changing

the blade, hold the reset button for more than 3 seconds to

reset the timer to zero and clear the display.

LOW BATTERY – This message will appear any time

a battery voltage problem occurs. The display will

automatically clear itself after the battery has been

serviced.

NOTE: When the LOW BATTERY message appears, it has

priority over any other messages. Service the battery first,

then check for other maintenance messages.

15

Not for

Reproduction

Operation

General Operating Safety

Be sure to read all information in the Operator Safety

section before attempting to operate this unit. Become

familiar with all of the controls and how to stop the unit.

WARNING

If the unit does not pass a safety test, do not operate it.

See an authorized dealer.

Safety Interlock System Tests

This unit is equipped with a Safety Interlock System. Do not

attempt to bypass or tamper with the switches/devices.

Test 1 — Engine should NOT crank if:

• PTO switch is ON, OR

• Brake pedal is NOT fully depressed (parking brake

OFF).

Test 2 — Engine SHOULD crank and start if:

• PTO switch is OFF, AND

• Brake pedal is fully depressed (parking brake ON),

Test 3 — Engine should SHUT OFF if:

• Operator rises off the seat with the PTO engaged.

• Operator rises off the seat with the brake pedal NOT

fully depressed (parking brake OFF).

Test 4 — Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a

complete stop within five seconds after electric PTO switch

is turned OFF. If mower drive belt does not stop within five

seconds, see an authorized dealer.

Test 5 — Check Reverse Mow Option (RMO)

• Engine should shut off if reverse travel is attempted if

the PTO has been switched on and RMO has not been

activated.

• RMO light should illuminate when RMO has been

activated.

WARNING

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. Never activate the RMO if children

are present. Children are often attracted to the unit and

the mowing activity.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

4).

NOTE: These pressures may differ slightly from the

“Maximum Inflation” stamped on the side walls of the tires.

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil

consumption. Check oil level more frequently.

16

Not for

Reproduction

Checking/Adding Oil

Before adding or checking the oil

• Place engine level.

• Clean the oil fill area of any debris.

1. Remove the dipstick (A, Figure 5) and wipe with a clean

cloth.

2. Insert and tighten the dipstick.

3. Remove the dipstick and check the oil level. It should

be at the FULL mark (B) on the dipstick.

4. If low, add oil slowly into the engine oil fill (C). Do not

overfill. After adding oil, wait one minute and then

recheck the oil level.

NOTE: Do not add oil at the quick oil drain (if equipped).

5. Replace and tighten the dipstick.

Oil Pressure

If the oil level is below the ADD mark, add oil until it reaches

the FULL mark. Start the engine and check for proper

pressure before continuing to operate.

If the oil level is between the ADD and FULL marks, do not

start the engine. Contact an authorized dealer to have the

oil pressure problem corrected.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane / 87 AKI (91 RON). For high

altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is

acceptable.

CAUTION: Do not use unapproved gasolines, such as E85.

Do not mix oil in gasoline or modify the engine to run on

alternate fuels. This will damage the engine components

and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel

stabilizer into the fuel. See the Storage section. All fuel is

not the same. If starting or performance problems occur,

change fuel providers or change brands. This engine is

certified to operate on gasoline. The emissions control

system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. For

carbureted engines, high altitude adjustment is required

to remain emissions compliant. Operation without this

adjustment will cause decreased performance, increased

fuel consumption, and increased emissions. Contact

a Briggs & Stratton Authorized Service Dealer for high

altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet

(762 meters) with the high altitude adjustment is not

recommended. For Electronic Fuel Injection (EFI) engines,

no high altitude adjustment is necessary.

Adding Fuel

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes

before removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the

fuel, do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting

engine.

1. Remove the fuel cap (A, Figure 6).

2. Clean the fuel cap area of dirt and debris.

3. Fill the fuel tank (B) with fuel. To allow for expansion

of the fuel, do not fill above the bottom of the fuel tank

neck (C).

4. Reinstall the fuel cap.

17

Not for

Reproduction

Starting the Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Starting Engine

• Ensure that spark plug, muffler, fuel cap, and air

cleaner (if equipped) are in place and secured.

• Do not crank engine with spark plug removed.

• If engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position

and crank until engine starts.

WARNING

Engines give off carbon monoxide, an odorless, colorless,

poison gas.

Breathing carbon monoxide can cause nausea, fainting,

or death.

Fire or explosion can cause severe burns or death.

• Start and run engine outdoors.

• Do not start or run engine in enclosed area, even if

doors or windows are open.

1. Check the oil level (see Check and Add Engine Oil).

2. Make sure equipment drive controls are disengaged.

3. Move the throttle/choke control to the CHOKE

position.

NOTE: Choke is usually unnecessary when restarting a

warm engine.

4. Insert the key into the ignition switch and turn it to the

ON/START position.

5. After the engine starts, move the throttle/choke

control to the FAST position. Warm up the engine by

running it for at least a minute before engaging the

blade rotation control or driving the rider.

6. After warming the engine, Always operate the rider

with the throttle/choke control in the FAST position.

In the event of an emergency the engine can be

stopped by simply turning the ignition switch to STOP.

Use this method only in emergency situations. For normal

engine shut down follow the procedure given in Stopping

the Tractor and Engine.

NOTE: If the engine does not start after repeated attempts,

contact an authorized dealer.

Driving the Tractor

1. Sit in the seat and adjust the seat so that you can

comfortably reach all the controls and see the

dashboard display (see Features and Controls).

2. Engage the parking brake. Fully depress the brake

pedal, pull UP on the parking brake control, and release

the brake pedal.

3. Make sure the PTO switch is disengaged.

4. Start the engine (see Starting the Engine).

5. Disengage the parking brake. Fully depress the brake

pedal, press DOWN on the parking brake control, and

release the brake pedal.

6. Depress the forward ground speed control pedal to

travel forward. Release the pedal to stop. Note that

the further down the pedal is depressed the faster the

tractor will travel.

7. Stop the tractor by releasing the ground speed control

pedals, setting the parking brake, and stopping the

engine (see Stopping the Tractor and Engine).

Mowing

1. Set the cutting height to the desired level using

the mower cutting height lever. See Features and

Controls.

2. Engage the parking brake. Make sure the PTO switch is

disengaged.

3. Start the engine. See Starting the Engine.

4. Set the throttle/ choke control to the FAST position.

5. Engage the PTO to activate the mower blades.

6. Begin mowing.

NOTE: When the “catcher full” alarm sounds, turn off

the PTO immediately to prevent the discharge tube from

plugging. Travel to the desired location and empty the

catcher. See Emptying the Catcher.

7. When finished mowing, shut off the PTO.

8. STOP the engine. See Stopping the

Tractor and Engine.

18

Not for

Reproduction

Reverse Mowing Option (RMO)

WARNING

Mowing in reverse can be hazardous to bystanders. Tragic

accidents can occur if the operator is not alert to the

presence of children. Never activate the RMO if children

are present. Children are often attracted to the unit and

the mowing activity.

The Reverse Mowing Option (RMO) allows the operator to

mow in reverse (see Features and Controls). To activate,

turn the RMO key after the PTO is engaged. The L.E.D. light

will illuminate, and the operator can then mow in reverse.

Each time the PTO is engaged the RMO needs to be

reactivated if desired. The key should be removed to restrict

access to the RMO.

Pushing the Tractor by Hand

1. Disengage the PTO and turn the engine off (see

Features and Controls).

2. Pull the lever toward the front of the unit and push down

to lock in place. Refer to Figure 7 for tractors with a

suspension system (A), and tractors with a fixed frame

(B). The tractor can now be pushed by hand.

3. Pull up and push toward the rear of the unit to engage

the transmission. The tractor can now be driven.

WARNING

Towing the unit will cause transmission damage. Do

not use another vehicle to push or pull this unit. Do not

actuate the transmission release lever while the engine is

running.

Parking Brake Function

Applying the Parking Brake - To lock the parking brake,

release the ground speed pedals, fully depress the brake

pedal, pull UP on the parking brake knob, and then release

brake pedal (see Features and Controls).

Releasing the Parking Brake - To release the parking

brake, fully depress the brake pedal and push the parking

brake knob DOWN (see Features and Controls).

Attaching a Trailer

The maximum horizontal drawbar force allowed is 150

Newton. The maximum vertical drawbar force is 90

Newton. This equates to a 113 kg (250 lbs) trailer on a 10

degree hill. Secure the trailer with an appropriately sized

clevis pin (A, Figure 9) and clip (B).

Cruise Control

TO ENGAGE:

1. Pull up on the cruise control knob (see Features and

Controls).

2. Depress the forward ground speed pedal.

3. Lift up the cruise control knob when desired speed is

reached. The Cruise will lock in one of its five locking

positions.

TO DISENGAGE:

1. Depress the brake pedal. See Features and Controls.

or

2. Depress the foward ground speed pedal.

Stopping the Tractor and Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

• Do not choke the carburetor to stop the engine.

1. Return the ground speed control(s) to neutral.

2. Disengage the PTO and wait for all moving parts to stop.

3. Move the throttle control (or throttle/choke control)

to SLOW position and turn the ignition key to OFF.

Remove the key.

Emptying the Catcher

1. Extend the grass catcher handle and rotate forward until

the grass catcher assembly is completely open at the

bottom. See Figure 8.

2. Empty the grass from the catcher.

3. Move the tractor forward a short distance. This will keep

the pile of grass from keeping the catcher from closing.

4. Rotate the grass catcher assembly back to the closed

position before mowing.

Cutting Height Adjustment

The mower lift lever is used to lower and raise the deck to

the desired cutting heigh. See Features and Controls.

The cutting height is adjustable between 3,8 cm (1,5”) and

8,9 cm (3,5”).

To lower the deck, pull back slightly on the mower lift lever,

push it to the left and slide it down. To raise the deck, pull

up on the mower lift lever and lock in notch to the right.

19

Not for

Reproduction

Maintenance

Maintenance Chart

TRACTOR AND MOWER

Every 8 Hours or Daily

Check safety interlock system

Clean debris off tractor and mower deck

Clean debris from engine compartment

Every 25 Hours or Annually *

Check tire pressure

Check mower blade stopping time

Check tractor and mower for loose hardware

Every 50 Hours or Annually *

Clean battery and cables

Check tractor brakes

See Dealer Annually to

Lubricate tractor and mower

Check mower blades **

* Whichever comes first

** Check blades more often in regions with sandy soils or high dust

conditions.

WARNING

Unintentional sparking can result in fire or electric shock.

Unintentional start-up can result in entanglement,

traumatic amputation, or laceration.

Before performing adjustments or repairs:

• Disconnect the spark plug wire and keep it away from

the spark plug.

• Disconnect battery at negative terminal (only engines

with electric start).

• Use only correct tools.

• Do not tamper with governor spring, links, or other

parts to increase engine speed.

• Replacement parts must be of the same design and

installed in the same position as the original parts.

Other parts may not perform as well, may damage the

unit, and may result in injury.

• Do not strike the flywheel with a hammer or hard object

because the flywheel may shatter during operation.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut (see Figure

7).

NOTE: These pressures may differ slightly from the

“Maximum Inflation” stamped on the side walls of the tires.

ENGINE

First 5 Hours

Change engine oil

Every 8 Hours or Daily

Check engine oil level

Every 25 Hours or Annually *

Clean engine air filter and pre-cleaner **

Every 50 Hours or Annually *

Change engine oil

Replace oil filter

Annually

Replace air filter

Replace pre-cleaner

See Dealer Annually to

Inspect muffler and spark arrester

Replace spark plug

Replace fuel filter

Clean engine air cooling system

* Whichever comes first

** Clean more often in dusty conditions or when airborne debris is present.

Check Tire Pressure

Tires should be checked periodically to provide the

optimum traction and to guarantee the best cut. See Figure

4 and the Specifications section.

NOTE: These pressures may differ slightly from the

“Maximum Inflation” stamped on the side walls of the tires.

ride.

Check Mower Blade Stopping Time

Mower blades and mower drive belt should come to a

complete stop within five seconds after the electric PTO

switch is turned off.

1. With tractor in neutral, PTO disengaged and operator in

seat, start the engine.

2. Engage the PTO and wait several seconds. Disengage

the PTO.

3. If mower drive belt does not stop within five seconds,

see an authorized dealer.

20

Sayfa yükleniyor...

Simplicity TRACTOR, EURO, RDLT Kullanım kılavuzu

Bu kılavuz aynı zamanda aşağıdakiler için de uygundur:

Simplicity TRACTOR, EURO, RDLT Kullanım kılavuzu

diğer dillerde

İlgili makaleler

Diğer belgeler